MRV-SideKick IV

MRV-SideKick IV
to rubber O-rings. Note: Do not use petroleum-based lubrication on O-rings. After
prolonged exposure to moisture, the bezel and batteries should be removed, inspected,
and dried if necessary.
WARNING: Lumapower reflectors are made with a highly precise process. Do not
touch or clean the reflecting surface using any cloth which may cause damage to the
MRV-SideKick IV
surface material affecting the illuminating performance.
Reflecting surface
Lumapower Innovative Flashlight
Inactive Periods.
If MRV-SIDEKICK IV is left unused for long period, the installed batteries should be
removed from the unit.
Output & Runtime
Accurately specifying light output (lumens) and runtime is complicated for LED flashlights.
Installed batteries and operating temperature are the main factors affecting the light
output and runtime. Lumapower cannot guarantee its products can reach the specification
under the using condition of users.
Reflector : SMO type
Output : 20 Lumens to 850+ Lumens (emitter Lumens)
Output Level :
Mode A : Ultra-100%, High-50%, Med-25%, Low-10%, Lowest-3%
Mode B : 12~14Hz Strobe, SOS, Light-house (0.2 Hz)
Runtime : 80 minutes Ultrra-out to 50% with 2x18650 2800mAh
200 minutes High-out to 50% with 2x18650 2800mAh
Input Voltage : 3.6V to 12V
Batteries : primary 123A, rechargeable Li-ion (18650, 17670…)
Length :178mm (without M-65), 246mm (with M-65)
Bezel Diameter : 45mm
Body Diameter : 25.4mm
Tail cap Diameter : 29mm
Reflector Diameter : 38mm
Weight : 197g / 232 g (Full size without battery installed)
Material : T6 aircraft aluminum with Type III HA
Body color : Black
Accessories : spare o-rings (for battery tube)
User Manual
Welcome to Lumapower
at (download the product registration form in the “download
page”) It enables us to keep you posted on our latest advancements, and helps us to
better understand our customers and build products that meet their needs and
Specifications: All product specifications/features are subject to change without notification.
This product has been designed and manufactured to the highest quality standards.
Convertible Design
However, if something does go wrong with this product, Lumapower and its national
The MRV-SIDEKICK IV can be operate with 2x18650 , (with M-65 battery tube installed).
distributors warrant free of charge labour and replacement parts in any country served by
Reflectors/LED engine module can be easily upgrade.
an official distributor.
Read Instructions. All the safety and operating instructions should be read before the
SideKick output control and Memory
SideKick-4 Digital output control
Mode A and Mode B :
product is operated.
Press and hold the SideKick switch for 2 seconds to switch from Mode A and Mode B.
Follow Instructions. All operating and use instructions should be followed.
High, Medium, Low and Lowest.
Unpacking: Check the product carefully. If it has been damaged in transit, report the
damage immediately by calling your dealer and/or the shipping company that delivered it.
Mode A : Quick press and release the SideKick switch to cycle the output from Ultra,
Replacement Parts. When replacement parts are required, be sure the replacement parts
have the same characteristics as the original part. Unauthorized substitutions may cause
Mode B: Quick press and release the SideKick switch to cycle the output from Tactical
Strobe, SOS and Light-house
Memory: The output level and status will be stored when you power off the light and
damage to the unit.
restore at next power on.
The Lumapower MRV-SIDEKICK IV supports input voltage from 3.6V to 12V.
The MRV-
SIDEKICK IV is fitted with pure white LED module driven by a constant current regulation
Battery Installation
circuitry to achieve a consistent level of light output for the useable life of the batteries.
Unscrew the tail or battery tube and insert new batteries with positive (+) ends towards
Li-ion rechargeable : LumaPower only recommends the use of PCB protected batteries.
LED assembly. Restore hand tighten. Depress tail cap pushbutton switch to test.
Battery Type
Rechargeable 18650 (3.7V)
Rechargeable 18650 (3.7V)
Primary 123A (3.0V)
Primary 123A (3.0V)
Due to battery chemistry’s limitations, 2 x CR123A only for emergency backup and
won’t offer max. output at all levels.
Note: Flashlight will not light if batteries are inserted in the wrong direction.
Damage may occur with reversed battery polarity.
CAUTION: MRV-SIDEKICK IV flashlights are high-output lighting devices. Due to
possible eye injury, DO NOT look directly into the reflector when the light is
switched on. Do not shine the MRV-SIDEKICK Ultra-III into the eyes of others.
Safety is your responsibility. External surface temperature will rise during prolonged
operation; this is a normal operating phenomenon.
Battery Replacement
If there is significant decrease in brightness of light output you should replace the batteries
with freshly charged batteries.
Unscrew the LED-engine and remove the old battery.
Insert a new battery as mentioned in Battery Installation Guide
WARNING: Lithium batteries can explode or cause burns if disassembled, shorted,
recharged, exposed to water, fire, or high temperatures. Do not place loose batteries in a
pocket, purse or other container containing metal objects or store with hazardous or
combustible materials. Store in cool, dry, ventilated area. Follow applicable laws and
regulations for disposal.
Convertible Design
The MRV-SIDEKICK IV can be operate with 2x18650 , (with M-65 battery tube installed).
Reflectors/LED engine module can be easily upgrade.
The MRV-SIDEKICK IV features a forward clicky switch and multi-level SideKick control
circuit with memory functions.
Half-press the tail switch to power ON MRV-SIDEKICK
momentary, full press to lock it for constant ON. Cycle press the SideKick to select output
Never use mixed-battery types or brands. Do not mix charged and uncharged
batteries. Input voltage limited to 12V, never use 4 x 16340 which may cause
circuit damage (with optional M-65 attached). Only use 2 x 18650 or 2 x 17650
or 4 x CR123A with M65. Power ON MRV-SIDEKICK IV at Ultra-out position
unattended over 15 minutes may cause overheating and damage.
Clean and lubricate threads with a clean cloth and apply thin coat of silicon-based lubricant
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF