Brentwood - Specific..
Brentwood™ SP
EPA Wood Burning Fireplaces
Specifications
Back Wall of Chase/Enclosure
Including Finising Materials if any
PRODUCT REFERENCE INFORMATION
Model: Brentwood SP, Cat. No. H4826
Weight
385 lbs
Height
36”
D
24-1/2”
Firebox W x H x D
measured in front
22” x 113/4” x 12”
Chimney weight ASHT* (6” dia)
6.25 lb/ft.
Chimney weight AC* (6” dia)
3.25 lb/ft.
Chimney weight S2100+*(6” dia)
10.8 lb/ft.
*Available from Security Chimneys™
FRAMING DIMENSIONS
Fireplace Opening Width
A
36-3/8”
924 mm
B
37”
940 mm
C
30-1/8”
D
13-1/2”
343 mm
Framing Dimensions
36”
Depth
E
77”
1956 mm
F
38-1/2”
978 mm
G
*24-1/2”
603 mm
54-7/16”
Listing Information
A
20-1/2”
Rough Framing Face (Unfinished Shown)
* Zero Clearance From Back Spacer to Wall
Combustible materials can NOT be
used in the space directly above
the fireplace. Do not fill the space
above the fireplace with any material (Except the wood framing)
E
2” x 3’
Min.
Header
Plywood 1/2”
B
1383 mm
7’
Min.
A
Fireplace Framing
28-3/32"
10-1/4"
These fireplaces have
been tested and listed
by ITS - Listing mark,
Warnock Hersey to ULCS610 & UL-127.
22-19/32"
Notes
Diagrams, illustrations and photographs are not to scale
– consult installation instructions. Product designs, materials,
dimensions, specifications, colors and prices are subject to
change or discontinuance without notice.
All framing dimensions calculated for 1/2" dry wall at the
fireplace face. If sheathing the chase or finishing with other
thickness materials, calculations will need to be made.
1"
* The fireplace must not be in contact with any insulation or
loose filling material. Cover the insulation with drywall panels
around the fireplace.
9-1/4"
12-1/2"
24"
Report No. 3011202
EPA Cert. No. 537
Parts Required
1-1/2"
36-13/16"
9-7/8"
14-5/32"
36-1/16"
12-1/4"
14-3/8"
2-13/16"
3-9/16"
22-1/2"
35-15/16"
• 6” diameter chimney * Model ASHT, S-2100+, HT6000+, HT6103+
or AC manufactured by Security Chimneys
International only, including:
- Chimney lengths
- Elbows (where necessary)
- Associated components as per
installation instructions manual
• ....Decorative Door - Required
(Order Separately)
.... - Available in black, gold or brushed nickel
• Outside air kit (Included)
OPTIONAL EQUIPMENT
17-3/4"
7-11/16"
24"
J
F
G
Rough Framing Face
(dimension includes finish
material inside framing, if any)
17-11/16"
19-3/32”
765 mm
* Total depth is 25 inches including the
back spacer minus 1/2 inch for drywall
to be flush with the facing.
Fireplace Dimensions
Corner Installation
C
L*
H
Width
J
OUTSIDE CHASE
• .. Additional Equipment
-. AC Chimney Adaptor *
. (required if using AC Chimney)
-. AC chimney outside air kit
- . Gravity venting system
-. Panel for clean face option
.(only with gravity venting system)
-. Rigid firescreen
-. UZY5 Fireplace Blower Kit
-. VRUW Blower Speed Control
*Available from Security Chimneys™
P/N 775550M REV. B 05/2013
Page 1 of 2
Brentwood™ SP
EPA Wood Burning Fireplaces
Specifications
Storm Collar
Rain Cap
Roof Support
Attic Radiation Shield
Collar
Flashing
Roof Support
Attic Radiation
Shield
Firestop
• Must have the same
firestopping resistance
as adjacent wall.
• Must have the same insulation as adjacent ceiling.
• Follow local rules regarding framing construction.
6-1/2” Min.
(to ceiling)
Firestop
68” Min.
6’ 8”
(2 m)
Min.
45” Min.
u
7’
(2.1 m)
Min.
Non-Combustible
Facing
Gravity Vent Kit (optional)
Outside Combustion
Air Kit (standard)
Drywall
1/2” Plywood
2” x 4”
Combustibles are not allowed below top spacers above the fireplace.
u
Facing in front of fireplace must be non-combustible below this area.
Combustible Clearances
CLEARANCE TO COMBUSTIBLES
The following clearances meet the minimum requirements
for a safe installation:
12” Max.
(305mm)
Side wall: 17” (324 mm) measured from the fireplace side.
Ceiling: 6’ 8” (2032 mm) measured from the base of the
fireplace.
Area where wood
Mantel can be
installed
Mantel
Fireplace enclosure:
Bottom: 0”
Side: 0” to spacer
Back: 0” to spacer
Top: Do not fill the space above the fireplace with any
material (Except the wood framing)
45”
(1143mm)
Min.
Hearth
Extension
Chimney: 2” (50 mm)
Mantel: 45” (1143 mm) measured from the base of the
fireplace.
18”
(457mm)
4”
(102mm)
45 Deg.
36”
(914mm)
17” Min.
(432mm)
Non-Combustible Material
Printed in U.S.A. © 2006 IHP LLC
P/N 775550M REV. B 05/2013
Floor
Ceiling
Wall
Floor,
Ceiling &
Wall
NOTE: It is recommended
that the chase walls and floor
be insulated in the same manner,
using the same insulation, as the rest
of the building, below the attic.
FIREPLACE
Typical Installations
Flashing
Page 2 of 2
• Must have
as adjacent
• Must have
ceiling.
• Follow loc
construction
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising