VW195xL / VW202xL / VW225xL Series LCD Monitor User

VW195xL / VW202xL / VW225xL Series LCD Monitor User
VW195xL /
VW202xL /
VW225xL Series
LCD Monitor
User Guide
MENU
E3774
First Edition V1
July 2008
Copyright © 2008 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless
such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identification or explanation and to the
owners’ benefit, without intent to infringe.
ii
Contents
Contents....................................................................................................... iii
Notices.......................................................................................................... iv
Safety information....................................................................................... vi
Care & Cleaning ......................................................................................... vii
Chapter 1:
Product introduction
1.1
Welcome! ..................................................................................... 1-1
1.2
Package contents.......................................................................... 1-1
1.3
Monitor introduction..................................................................... 1-2
1.3.1
Front view........................................................................ 1-2
1.3.2
Back view......................................................................... 1-3
Chapter 2:
Setup
2.1
Assembling the monitor base...................................................... 2-1
2.2
Adjusting the monitor angles...................................................... 2-2
2.3
Detaching the arm/base (for VESA wall mount)......................... 2-2
2.4
Disassembling the monitor base (for product packing)............ 2-4
2.5
Connecting the cables.................................................................. 2-4
2.6
Turning on the monitor................................................................. 2-5
Chapter 3:
3.1
General instruction
OSD (On-Screen Display) menu ................................................. 3-1
3.1.1
How to reconfigure........................................................... 3-1
3.1.2
OSD Function Introduction............................................... 3-1
3.2
Specifications summary............................................................... 3-4
3.3
Troubleshooting (FAQ)................................................................. 3-7
3.4
Supported operating modes........................................................ 3-8
iii
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
•
This device may not cause harmful interference, and
•
This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with manufacturer’s
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is
required to assure compliance with FCC regulations. Changes or modifications
to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
As an Energy Star® Partner, our company has determined that this product meets
the Energy Star® guidelines for energy efficiency.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
iv
TCO Development
Congratulations!
The display you have just purchased carries the
TCO’03 Displays label. This means that your
display is designed, manufactured and tested
according to some of the strictest quality and
environmental requirements in the world. This
makes for a high performance product, designed
with the user in focus that also minimizes the
impact on our natural environment.
Some of the features of the TCO’03 Display requirements:
Ergonomics
• Good visual ergonomics and image quality in order to improve the working
environment for the user and to reduce sight and strain problems. Important
parameters are luminance, contrast, resolution, reflectance, colour rendition
and image stability.
Energy
• Energy-saving mode after a certain time – beneficial both for the user and the environment
• Electrical safety
Emissions
•
Electromagnetic fields
•
Noise emissions
Ecology
•
The product must be prepared for recycling and the manufacturer must have a
certified environmental management system such as EMAS or ISO 14 001
•
Restrictions on
- chlorinated and brominated flame retardants and polymers
- heavy metals such as cadmium, mercury and lead.
The requirements included in this label have been developed by TCO
Development in cooperation with scientists, experts, users as well as
manufacturers all over the world. Since the end of the 1980s TCO has been
involved in influencing the development of IT equipment in a more user-friendly
direction. Our labelling system started with displays in 1992 and is now requested
by users and IT-manufacturers all over the world.
For more information, please visit www.tcodevelopment.com
Safety information
•
Before setting up the monitor, carefully read all the documentation that came
with the package.
•
To prevent fire or shock hazard, never expose the monitor to rain or moisture.
•
Never try to open the monitor cabinet. The dangerous high voltages inside the
monitor may result in serious physical injury.
•
If the power supply is broken, do not try to fix it by yourself. Contact a qualified
service technician or your retailer.
•
Before using the product, make sure all cables are correctly connected and the
power cables are not damaged. If you detect any damage, contact your dealer
immediately.
•
Slots and openings on the back or top of the cabinet are provided for
ventilation. Do not block these slots. Never place this product near or over a
radiator or heat source unless proper ventilation is provided.
•
The monitor should be operated only from the type of power source indicated
on the label. If you are not sure of the type of power supply to your home,
consult your dealer or local power company.
•
Use the appropriate power plug which complies with your local power
standard.
•
Do not overload power strips and extention cords. Overloading can result in
fire or electric shock.
•
Avoid dust, humidity, and temperature extremes. Do not place the monitor in
any area where it may become wet. Place the monitor on a stable surface.
•
Unplug the unit during a lightning storm or if it will not be used for a long period
of time. This will protect the monitor from damage due to power surges.
•
Never push objects or spill liquid of any kind into the slots on the monitor
cabinet.
•
To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked between
100-240V AC.
•
If you encounter technical problems with the monitor, contact a qualified
service technician or your retailer.
This symbol of the crossed out wheeled bin indicates that the product (electrical
and electronic equipment) should not be placed in municipal waste.
Please check local regulations for disposal of electronic products.
vi
Care & Cleaning
•
Before you lift or reposition your monitor, it is better to disconnect the cables
and power cord. Follow the correct lifting techniques when positioning the
monitor. When lifting or carrying the monitor, grasp the edges of the monitor.
Do not lift the display by the stand or the cord.
•
Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor
surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed
with a cloth dampened with mild cleaner.
•
Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended
for use with the LCD. Never spray cleaner directly on the screen, as it may drip
inside the monitor and cause an electric shock.
The following symptoms are normal with the monitor:
•
The screen may flicker during the initial use due to the nature of the fluorescent
light. Turn off the Power Switch and turn it on again to make sure that the
flicker disappears.
•
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
•
When the same image is displayed for hours, an afterimage of the previous
screen may remain after switching the image. The screen will recover slowly or
you can turn off the Power Switch for hours.
•
When the screen becomes black or flashes, or cannot work anymore, contact
your dealer or service center to fix it. Do not repair the screen by yourself!
Conventions used in this guide
To make sure that you perform certain tasks properly, take note of the following
symbols used throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself
when trying to complete a task.
CAUTION: Information to prevent damage to the components
when trying to complete a task.
IMPORTANT: Instructions that you MUST follow to complete a
task.
NOTE: Tips and additional information to help you complete a
task.
vii
Where to find more information
Refer to the following sources for additional information and for product and
software updates.
1.
ASUS websites
The ASUS websites worldwide provide updated information on ASUS
hardware and software products. Refer to http://www.asus.com
2.
Optional documentation
Your product package may include optional documentation that may have
been added by your dealer. These documents are not part of the standard
package.
viii
1.1
Welcome!
Thank you for purchasing the ASUS® VW195xL/VW202xL/VW225xL Series LCD
monitor!
The latest widescreen LCD monitor from ASUS provides a crisper, broader, and
brighter display, plus a host of features that enhance your viewing experience.
With these features, you can enjoy the convenience and delightful visual
experience that the VW195xL/VW202xL/VW225xL Series brings you!
1.2
Package contents
Check your VW195xL/VW202xL/VW225xL Series LCD monitor package for the
following items:
•
LCD monitor
•
Monitor base
•
Quick start guide
•
1 x Power cord
•
1 x VGA cable
•
1 x DVI cable
•
1 x Audio cable
If any of the above items is damaged or missing, contact your retailer
immediately.
ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor
1-1
1.3
Monitor introduction
1.3.1
Front view
MENU
Base
1
1.
5
•
Use this hotkey to switch from five video preset modes (Game Mode,
Night View Mode, Scenery Mode, Standard Mode, Theater Mode) with
SPLENDID™ Video Enhancement Technology.
•
Exit the OSD menu or go back to the previous menu as the OSD menu
is activated.
•
Automatically adjust the image to its optimized position, clock, and phase
by pressing this button for 2-4 seconds (for VGA mode only).
Button:
•
Press this button to decrease the value of the function selected or move
left/up to the previous function.
•
This is also a Volume hotkey for model with speaker or Contract hotkey
for model without speaker.
MENU Button:
•
4.
1-2
4
3
Button:
2.
3.
2
Press this button to enter/select the icon (function) highlighted while the
OSD is activated.
Button:
•
Press this button to increase the value of the function selected or move
right/down to the next fuction.
•
This is also a hotkey for Brightness adjustment.
Chapter 1: Product introduction
5.
Power button/power indicator
•
Press this button to turn the monitor on/off.
•
The color definition of the power indicator is as the table below.
Status
Blue
Amber
OFF
1.3.2
Description
ON
Standby mode
OFF
Back view
Stereo
speaker
Stereo
speaker
Screw holes for
VESA Wall Mount
Rear connectors
Monitor base
release button
1
2
3
4
Rear connectors
1.
Audio-in port. This port connects PC audio source by the bundled audio
cable.
2.
AC-IN port. This port connects the power connector from the bundled power
cord.
3.
DVI port. This 24-pin port is for PC (Personal Computer) DVI-D digital signal
connection.
4.
VGA port. This 15-pin port is for PC VGA connection.
The VESA wall mount kit (100 mm x 100 mm) is purchased separately.
ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor
1-3
1-4
Chapter 1: Product introduction
2.1
Assembling the monitor base
To assemble the monitor base
1.
Have the monitor base place on a flat table.
2.
Connect the base with the arm according to the below drawing. A click sound
shows that the base has been connected successfully.
3.
Remove the monitor height adjustment lock.
2
3
1
The monitor height adjustment lock should NEVER be removed BEFORE you
place the monitor VERTICALLY on a flat surface.
ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor
2-1
2.2
Adjusting the monitor angles
•
For optimal viewing, we recommend that you look at the full face of the monitor,
then adjust the monitor to the angle that is most comfortable for you.
•
Hold the base to prevent the monitor from falling when you change its angle.
•
You can tilt the monitor’s from -3º to 20º, swivel from left-to-right for 45º, and lift
the monitor’s height for about 70mm.
-3º~20º
70mm
45º
45º
0º
2.3
Detaching the arm/base (for VESA
wall mount)
The detachable arm / base of the VW195xL/VW202xL/VW225xL Series LCD
monitor is specially designed for VESA wall mount.
To detach the arm/base
2-2
1.
Lower the monitor to its lowest height, and then insert the monitor height
adjustment lock (Figure 1).
2.
Have the front of the monitor face down on a table.
3.
Remove the rubbers in the four screw holes (Figure 2).
4.
Use a screwdriver to remove the two screws on the arm (Figure 2), then slide
out the arm/base to detach it from the monitor (Figure 3).
Chapter 2: Setup
Figure 1
Rubbers in the
screw holes
Two screws
Arm/base
Figure 2
Figure 3
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor
2-3
2.4
Disassembling the monitor base (for
product packing)
To disassemble the monitor base
1.
Lower the monitor to its lowest height, and then insert the monitor height
adjustment lock.
2.
Have the front of the monitor face down on a table.
3.
Press and hold the release button on the monitor base and remove the
monitor base from the monitor arm.
3
1
2.5
1.
Connect the cables as the following instructions:
•
To connect the audio cable: connect one end of the audio cable to the
monitor’s Audio-in port, the other end to the computer's audio-out port.
•
To connect the power cord: connect one end of the power cord securely to
the monitor’s AC input port, the other end to a power outlet.
•
To connect the VGA/DVI cable:
2-4
Connecting the cables
a.
b.
c.
Plug the VGA/DVI connector to the LCD monitor’s VGA/DVI port.
Connect the other end of the VGA/ DVI cable to your computer’s VGA/
DVI port.
Tighten the two screws to secure the VGA/DVI connector.
Chapter 2: Setup
When both the VGA and the DVI cables are connected, you can choose either
VGA mode or DVI mode from the Input Select item of the OSD functions.
2.
Gather all the cables with the cable hook.
Cable hook
2.6
Turning on the monitor
Gently press the power button . See page 1-2 for the location of the power
button. The power indicator lights up in blue to show that the monitor is ON.
ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor
2-5
2-6
Chapter 2: Setup
3.1
OSD (On-Screen Display) menu
3.1.1
How to reconfigure
1.
Press the MENU button to activate the
OSD menu.
2.
Press
and
to navigate through
the functions. Highlight and activate the
desired function by pressing the MENU
button. If the function selected has a
sub-menu, press
and
again to
navigate through the sub-menu functions.
Highlight and activate the desired submenu function by pressing the MENU button.
3.
Press
4.
To exit the OSD menu, press the
adjust any other function.
3.1.2
1.
and
to change the settings of the selected function.
button. Repeat step 2 and step 3 to
OSD Function Introduction
Spendid
This function contains five sub-functions
you can select for your preference. Each
mode has the Reset selection, allowing
you to maintain your setting or return to
the preset mode.
•
Scenery Mode: best choice for
scenery photo display with
SPLENDID™ Video Enhancement.
•
Standard Mode: best choice for document editing with SPLENDID™
Video Enhancement.
•
Theater Mode: best choice for movie with SPLENDID™ Video
Enhancement.
•
Game Mode: best choice for game playing with SPLENDID™ Video
Enhancement.
•
Night View Mode: best choice for dark-scene game or movie with SPLENDID™ Video Enhancement.
•
In the Standard Mode, the Satuation and Sharpness functions are not userconfigurable.
•
In the other modes, the sRGB function is not user-configurable.
ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor
3-1
2.
Image
You can adjust brightness, contrast,
sharpness, saturation, position (VGA only),
ASCR, and focus (VGA only) from this
main function.
3.
•
Brightness: the adjusting range is
from 0 to 100.
is a hotkey to
activate this function.
•
Contrast: the adjusting range is from
0 to 100.
•
ASCR: turns on/off the ASCR(ASUS Smart Contrast Ratio) function.
•
Sharpness: the adjusting range is from 0 to 100.
•
Saturation: the adjusting range is from 0 to 100.
•
Position: adjusts the horizontal postition (H-Position) and the vertical
position (V-Position) of the image. The adjusting range is from 0 to 100.
•
Focus: reduces Horizonal-line noise and Vertical-line noise of the image
by adjusting (Phase) and (Clock) separately. The adjusting range is from
0 to 100.
•
Phase adjusts the phase of the pixel clock signal. With a wrong phase
adjustment, the screen shows horizontal disturbances.
•
Clock (pixel frequency) controls the number of pixels scanned by one
horizontal sweep. If the frequency is not correct, the screen shows vertical
stripes and the image is not proportional.
Color
Select the image color you like from this
function.
•
Color Temp.: contains five color
modes including Cool, Normal, Warm,
sRGB, and User mode.
•
Skin Tone: contains three color
modes including Reddish, Natural,
and Yellowish.
In the User mode, colors of R (Red), G (Green), and B (Blue) are userconfigurable; the adjusting range is from 0-100.
3-2
Chapter 3: General Instruction
4.
Input Select
In this function, you can select either
VGA or DVI input source. (Only for some
models)
5.
System Setup
Allow you to adjust the system.
•
Volume: the adjusting range is from 0
to 100.
is a hotkey to activate this
function.
•
OSD Setup:
* Adjusts the horizontal postition
(H-Position)/ the vertical position
(V-Position) of the OSD from 0 to 100.
* Adjusts the OSD timeout from 10 to 120.
* Enables or disables the DDC/CI function.
•
Language: there are ten languages for your selection, including English,
German, Italian, French, Dutch, Spanish, Russian, Traditional Chinese,
Simplified Chinese, and Japanese.
•
Aspect Control: adjusts the aspect ratio to “Full” or “4:3”.
•
Information: shows the monitor information.
•
Reset: “Yes” allows you to restore the default setting.
ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor
3-3
3.2
Specifications summary (VW195xL
Series)
Panel Type
Panel size
Max. Resolution
Pixel pitch
Brightness (Typ.)
Brightness (Max.)
Contrast Ratio (Typ.)
Contrast Ratio (Max.)
Viewing angle(H/V) CR>10
Display colors
Response time
SPLENDID™ Video
Enhancement
SPLENDID™ selection
Auto adjustment
Color temperature selection
Skin-Tone selection
Digital input
Analog input
Audio-in port
Colors
Speaker (Built-in)
Power LED
VESA wall mount
Tilt
Swivel
Height adjustment
Kensington lock
Voltage rating
Power consumption
TFT LCD
19" (16:10) wide screen
WXGA+ 1440 x 900
0.285mm
250cd/m2
300cd/m2
800:1
2000:1 (with ASCR ON)
160˚/160˚
16.7M
5ms
Temperature (Operating)
Temperature
(Non-operating)
0˚C~40˚C
Dimension (W x H x D)
Weight (Esti.)
Multi-languages
Accessories
Regulation approvals
Yes
5 video preset modes (by hotkey)
Yes (by hotkey)
5 color temperatures
3 skin-tones
DVI-D with HDCP (VW195TL / VW195NL)
D-Sub
3.5 mm Mini-jack (VW195TL / VW195SL)
Black
1W x 2 Stereo, RMS (VW195TL / VW195SL)
Blue (On) / Amber (Standby)
100 x 100mm
-5˚~+20˚
-45˚~+45˚
70mm
Yes
AC: 100~240V
Power On : < 47W, Standby: < 2W, Power Off: <1W
-20˚C~+60˚C
444 mm x 376 mm x 214 mm (machine)
516 mm x 456 mm x 175 mm (package)
4.2 kg (Net) ; 6.5 kg (Gross)
10 languages (English, German, Italian, French, Dutch,
Spanish, Russian, Traditional Chinese, Simplified
Chinese, Japanese)
VGA cable, DVI cable, audio cable, power cord, quick
start guide, warranty card
Energy Star®, CB, CE, Gost-R, CCC, UL, FCC, C-Tick,
BSMI, VCCI, TCO03, RoHS, WEEE, PSB
*Specifications are subject to change without notice.
3-4
Chapter 3: General Instruction
Specifications summary (VW202xL Series)
Panel Type
Panel size
Max. Resolution
Pixel pitch
Brightness (Typ.)
Brightness (Max.)
Contrast Ratio (Typ.)
Contrast Ratio (Max.)
Viewing angle(H/V) CR>10
Display colors
Response time
SPLENDID™ Video
Enhancement
SPLENDID™ selection
Auto adjustment
Color temperature selection
Skin-Tone selection
Digital input
Analog input
USB 2.0 PC input
Audio-in port
Colors
Speaker (Built-in)
Power LED
VESA wall mount
Tilt
Swivel
Height adjustment
Kensington lock
Voltage rating
Power consumption
TFT LCD
20.1" wide screen
WSXGA+ 1680 x 1050
0.258mm
250cd/m2
300cd/m2
1000:1
3000:1 (with ASCR ON)
160˚/160˚
16.7M
5ms
Temperature (Operating)
Temperature
(Non-operating)
0˚C~40˚C
Dimension (W x H x D)
Weight (Esti.)
Multi-languages
Accessories
Regulation approvals
Yes
5 video preset modes (by hotkey)
Yes (by hotkey)
5 color temperatures
3 skin-tones
DVI-D with HDCP (VW202TL / VW202NL)
D-Sub
VW202BL only
3.5 mm Mini-jack (VW202TL / VW202SL)
Black
1W x 2 Stereo, RMS (VW202TL / VW202SL)
Blue (On) / Amber (Standby)
100 x 100mm
-5˚~+20˚
-45˚~+45˚
70mm
Yes
AC: 100~240V
Power On : < 49W, Standby: < 2W, Power Off: <1W
-20˚C~+60˚C
479 mm x 392 mm x 214 mm (machine)
550 mm x 480 mm x 175 mm (package)
4.4 kg (Net) ; 6.8 kg (Gross)
10 languages (English, German, Italian, French, Dutch,
Spanish, Russian, Traditional Chinese, Simplified
Chinese, Japanese)
VGA cable, DVI cable, audio cable, USB cable
(VW202BL only), power cord, quick start guide, warranty
card
Energy Star®, CB, CE, Gost-R, CCC, CSA, FCC, C-Tick,
BSMI, VCCI, TCO03, RoHS, WEEE, PSB
*Specifications are subject to change without notice.
ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor
3-5
Specifications summary (VW225xL Series)
Panel Type
Panel size
Max. Resolution
Pixel pitch
Brightness (Typ.)
Brightness (Max.)
Contrast Ratio (Typ.)
Contrast Ratio (Max.)
Viewing angle(H/V) CR>10
Display colors
Response time
SPLENDID™ Video
Enhancement
SPLENDID™ selection
Auto adjustment
Color temperature selection
Skin-Tone selection
Digital input
Analog input
Audio-in port
Colors
Speaker (Built-in)
Power LED
VESA wall mount
Tilt
Swivel
Height adjustment
Kensington lock
Voltage rating
Power consumption
TFT LCD
22.0" (16:10) wide screen
WSXGA+ 1680 x 1050
0.282mm
250cd/m2
300cd/m2
1000:1
8000:1 (with ASCR ON)
170˚/160˚
16.7M
5ms
Temperature (Operating)
Temperature
(Non-operating)
0˚C~40˚C
Dimension (W x H x D)
Weight (Esti.)
Multi-languages
Accessories
Regulation approvals
Yes
5 video preset modes (by hotkey)
Yes (by hotkey)
5 color temperatures
3 skin-tones
DVI-D with HDCP (VW225TL / VW225NL)
D-Sub
3.5 mm Mini-jack (VW225TL / VW225SL)
Black
1W x 2 Stereo, RMS (VW225TL / VW225SL)
Blue (On) / Amber (Standby)
100 x 100mm
-5˚~+20˚
-45˚~+45˚
70mm
Yes
AC: 100~240V
Power On : < 55W, Standby: < 2W, Power Off: <1W
-20˚C~+60˚C
513 mm x 405 mm x 214 mm (machine)
601 mm x 487 mm x 175 mm (package)
5.0 kg (Net) ; 7.6 kg (Gross)
10 languages (English, German, Italian, French, Dutch,
Spanish, Russian, Traditional Chinese, Simplified
Chinese, Japanese)
VGA cable, DVI cable, audio cable, power cord, quick
start guide, warranty card
Energy Star®, CB, CE, Gost-R, CCC, UL, FCC, C-Tick,
BSMI, VCCI, TCO03, RoHS, WEEE, PSB
*Specifications are subject to change without notice.
3-6
Chapter 3: General Instruction
3.3
Troubleshooting (FAQ)
Problem
Possible Solution
Power LED is not ON
• Press the button to check if the monitor
is in the ON mode.
• Check if the power cord is properly
connected to the monitor and the power
outlet.
The power LED lights amber and there is no • Check if the monitor and the computer are
screen image
in the ON mode.
• Make sure the signal cable is properly connected the monitor and the computer.
• Inspect the signal cable and make sure
none of the pins are bent.
• Connect the computer with another
available monitor to check if the computer
is properly working.
Screen image is too light or dark
• Adjust the Contrast and Brightness settings
via OSD.
Screen image is not centered or sized
• Press the
button for two seconds to
properly
automatically adjust the image.
• Adjust the H-Position or V-Position settings
via OSD.
Screen image bounces or a wave pattern is • Make sure the signal cable is properly
present in the image
connected to the monitor and the computer.
• Move electrical devices that may cause
electrical interference.
Screen image has color defects (white does • Inspect the signal cable and make sure that
not look white)
none of the pins are bent.
• Perform Reset via OSD.
• Adjust the R/G/B color settings or select the
Color Temperature via OSD.
Screen image is blurry or fuzzy
• Press the
button for two seconds to
automatically adjust the image (for VGA
mode only).
• Adjust the Phase and Clock settings via
OSD.
No sound or sound is low
• Ensure that the audio cable is properly
connected to the monitor and the computer
• Adjust the volume settings of both your
monitor and computer.
• Ensure that the computer sound card driver
is properly installed and activated.
ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor
3-7
3.4
Standard
DOS
VGA
SVGA
XGA
SXGA
VESA
UXGA
VESA
Supported operating modes
Resolution
Frequency
720 x 400
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1280 x 960
1280 x 1024
1280 x 1024
1152 x 864
1440 x 900
(VW195xL Primary)
1600 x 1200
1680 x 1050
(VW202xL / VW225xL
Primary)
Horizontal
Frequency
31.47KHz
31.47KHz
37.90KHz
37.50KHz
35.16KHz
37.90KHz
48.10KHz
46.90KHz
48.40KHz
56.50KHz
60.02KHz
60.00KHz
64.00KHz
80.00KHz
67.50KHz
Vertical
Frequency
70Hz
60Hz
72Hz
75Hz
56Hz
60Hz
72Hz
75Hz
60Hz
70Hz
75Hz
60Hz
60Hz
75Hz
75Hz
Pixel
55.94KHz
60Hz
106.5MHz
75.00KHz
60Hz
162.00MHz
65.29KHz
60Hz
146.25MHz
28.32MHz
25.18MHz
31.50MHz
31.50MHz
36.00MHz
40.00MHz
50.00MHz
49.50MHz
65.00MHz
75.00MHz
78.75MHz
108.00MHz
108.00MHz
135.00MHz
108.00MHz
* Modes not listed in the table may not be supported. For optimal resolution, we recommend that you choose a mode listed in the table above.
3-8
Chapter 3: General Instruction
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising