F220 Heat Detectors - Bosch Security Systems

F220 Heat Detectors - Bosch Security Systems
Fire Alarm Systems | F220 Heat Detectors
F220 Heat Detectors
www.boschsecurity.com
The F220 Heat Detectors include:
• F220‑135: An electronic rate-of-rise, fixed
temperature heat detector that initiates an alarm
when the ambient temperature exceeds +135°F
(+57°C) or when the ambient temperature increases
by +15°F (+8.3°C) or more in less than 1 minute
• F220‑135F: An electronic fixed temperature heat
detector that initiates an alarm when the ambient
temperature reaches +135°F (+57°C).
• F220‑190F: An electronic fixed temperature heat
detector that initiates an alarm when the ambient
temperature reaches +190°F (+88°C).
The detectors use low current electronic circuitry, so
they can connect to 12 VDC nominal or 24 VDC
nominal power source circuits. When mounted on the
appropriate F220‑B6 Series Mounting Base, the F220
Heat Detectors provide general property protection
from fire.
Notice
Heat detectors are not life safety devices.
u
Two-wire or four-wire bases
u
50 ft (15.2 m) maximum spacing between detectors
u
Visible identification of model: F220‑135 = no ring,
F220‑135F = gray ring, F220‑190F = black ring
u
Tamper detection
u
Dual color LED
Functions
Compatible Bases
Configure the detectors as either two-wire or four-wire
depending on the mounting base selected. These
detectors are compatible with any of the F220‑B6
bases:
• F220‑B6 12/24 VDC Two-wire Mounting Base
• F220‑B6R Standard 12/24 VDC Four-wire Mounting
Base
• F220‑B6RS 24 VDC Four-wire Mounting Base with
Sounder
• F220‑B6C 12/24 VDC Four-wire Mounting Base with
Auxiliary Form C Relay
• F220‑B6E 12/24 VDC Four-wire Power Supervision
Mounting Base
• F220‑B6PM 24 VDC Four-wire Addressable Master
Base
• F220‑B6PS 12/24 VDC Four-wire Addressable Base
Dual-color LED
To verify the detector has power and the heat
detection circuitry functions, a dual-color LED
indicator flashes green every 8 sec when operating
normally. It flashes once every 4 sec when a trouble
condition exists. The LED latches on red if an alarm
2 | F220 Heat Detectors
occurs, allowing the user to easily verify individual
detector alarms. Clear the alarm condition by
interrupting power to the detector.
Tamper Detection
When detector heads are correctly installed in any of
the F220‑B6 bases, the control panel initiates a
trouble signal if a detector is removed from its base. A
mechanical tamper lock comes with each base to
inhibit unauthorized head removal.
Supervision
The control panel supervises two-wire systems.
Supervision of four-wire system power is provided by
an end-of-line (EOL) power supervision device such as
a D275 or PAM-4, or an F220‑B6E Power Supervision
Mounting Base and an EOL resistor as specified by the
control panel manufacturer.
Certifications and approvals
Depending on local regulations, the bases can be
surface mounted directly on four-inch square or
octagonal electrical boxes and single-gang switch
boxes.
Notice
The volume of any electrical box used should be
adequate to accommodate the number and size of
conductors as specified by the National Electrical
Code or any local authorities having jurisdiction
(AHJ).
End-of-Line Power Supervision
Loop supervision requires one D275 or PAM-4 or
F220‑B6E per loop when using F220‑B6R/B6C bases
and is accomplished by the control panel.
Wiring the Bases
For detailed wiring instructions, see the F220 Series
Detectors with F220‑B6/C/E/R Bases Installation
Instructions, the F220 Series Detectors with
F220‑B6RS Bases Installation Instructions, or the
F220‑B6PS/M Installation Instructions.
Region
Certification
Europe
CE
89/336/EEC, EN50130-4/A Sept 1998,
EN61000-6-3 Oct 2001
USA
UL
UQGS: Heat - Automatic Fire Detectors
(UL521)
Parts included
FM
F220 Heats
Quanti
ty
Component
CSFM
see our website
1
Detector head with dust cover
NYCMEA
117-05-E
MSFM
2200 Sep 2008
HKFSD
J-002/C/067
Hong Kong
Installation/configuration notes
Compatible Control Panels
Addressable Systems: These detectors are compatible
with addressable systems controlled by D9412GV2,
D7412GV2, D9412G, or D7412G Control Panels or the
D9124 Fire Alarm Control Panel when used with the
F220‑B6PM or F220‑B6PS Addressable Detector
Bases.
Two-wire: Bosch Security Systems, Inc. makes no
claim written, oral, or implied that these detectors
work with any two-wire control panels except those
specified in the Control Panel Compatibility chart in
the Technical Service Note (P/N: 4998148185).
Four-wire: Thes detectors are compatible with all UL
Listed four‑wire control panels. For proper end-of-line
(EOL) resistor selection, see the control panel's
installation instructions.
Mounting the Bases
Notice
Consult NFPA 72 for proper detector placement.
Technical specifications
Electrical
Current (alarm):
(detector head only)
20 mA minimum at 8.5 VDC;
35 mA maximum at 32 VDC
Current (start‑up
\standby):
0.12 mA maximum at 35 VDC
Maximum RMS Ripple:
25% of DC input
Power-up Time:
22 sec maximum
Voltage (standby)
F220‑B6:
8.5 VDC to 32.0 VDC
F220‑B6C/‑B6R/‑B6E:
10.0 VDC to 30.0 VDC
F220‑B6RS:
16.0 VDC to 30.0 VDC
F220‑B6PM:
18.9 VDC to 28.0 VDC
F220‑B6PS:
With D299: 18.9 VDC to 28.0 VDC
Without D299: 9.6 VDC to 28.0 VDC
Environmental
Relative Humidity:
0% to 95% non-condensing
Temperature
(normal operating):
+32°F to +100°F (0°C to +38°C)
Note: The normal environment where these detectors are installed
should be within the specified normal operating temperature limits.
3 | F220 Heat Detectors
Mechanical
Color:
White
Dimensions
(diameter x H):
6.75 in. x 2.25 in. (17.1 cm x 6.4 cm)
F220‑B6C 12/24 VDC Four‑wire Base with Auxiliary
Form C Relay
Four‑wire base with a normally‑open (NO) alarm loop
relay and a set of auxiliary contacts (Form C).
Order number F220-B6C
Trademarks
All hardware and software product names used in this
document are likely to be registered trademarks and
must be treated accordingly.
F220‑B6E 12/24 VDC Four‑wire Power Supervision Base
with End‑of‑line Power Monitoring Relay
Ordering information
Order number F220-B6E
F220‑135 Electronic Rate‑of‑Rise/Fixed Temperature
(+135°F [+57°C]) Heat Detector
Rate‑of‑rise/fixed temperature heat detector head
only; requires base.
Order number F220-135
F220‑135F Electronic Fixed Temperature (+135°F
[+57°C]) Heat Detector
Fixed temperature heat detector head only; requires
base.
Order number F220-135F
F220‑190F Electronic Fixed Temperature (+190°F
[+88°C]) Heat Detector
Fixed temperature heat detector head only; requires
base.
Order number F220-190F
Accessories
D275 Power Supervision Module
Line supervision device for four-wire fire detection
circuits
Order number D275
DRA‑5 Remote Annunciator (5 VDC)
Designed to provide remote annunciation of alarms for
a number of Bosch smoke and heat detectors
Order number DRA-5
DT‑2 Detector Removal Tool
Use the DT‑2 to remove, replace, or test the detector
head
Order number DT-2
F220‑B6 12/24 VDC Two‑wire Base
Standard base for two‑wire (12 VDC or 24 VDC
system) applications.
Order number F220-B6
F220‑B6R Standard 12/24 VDC Four‑wire Base
Standard base for four‑wire (12 VDC or 24 VDC)
detector systems.
Order number F220-B6R
F220‑B6RS 24 VDC Four‑wire Detector Base with Sounder
Four-wire detector base with sounder for use with the
F220 Photoelectric Smoke and Heat Detectors.
Order number F220-B6RS
Four‑wire base with a normally‑open (NO) alarm relay
and an EOL power supervision relay.
F220‑B6PM 24 VDC Four‑wire Addressable Multiple Detector Base
The multiple detector base provides an address on the
FACP data expansion circuit for its detector and up to
an additional 19 detectors. It accepts the F220
Photoelectric Smoke Detector Heads and Heat
Detector Heads.
Order number F220-B6PM
F220‑B6PS 12/24 VDC Four‑wire Addressable Single Detector Base
The single detector base provides an address on the
FACP data expansion circuit for its detector. It accepts
the F220 Photoelectric Smoke Detector Heads and
Heat Detector Heads.
Order number F220-B6PS
4 | F220 Heat Detectors
Represented by:
Americas:
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, New York, 14450, USA
Phone: +1 800 289 0096
Fax: +1 585 223 9180
security.sales@us.bosch.com
www.boschsecurity.us
Europe, Middle East, Africa:
Bosch Security Systems B.V.
P.O. Box 80002
5617 BA Eindhoven, The Netherlands
Phone: + 31 40 2577 284
Fax: +31 40 2577 330
emea.securitysystems@bosch.com
www.boschsecurity.com
© Bosch Security Systems 2015 | Data subject to change without notice
2701717003 | en, V8, 27. Jul 2015
Asia-Pacific:
Robert Bosch (SEA) Pte Ltd, Security
Systems
11 Bishan Street 21
Singapore 573943
Phone: +65 6571 2808
Fax: +65 6571 2699
apr.securitysystems@bosch.com
www.boschsecurity.asia
China:
America Latina:
Bosch (Shanghai) Security Systems Ltd. Robert Bosch Ltda Security Systems Division
203 Building, No. 333 Fuquan Road
Via Anhanguera, Km 98
North IBP
CEP 13065-900
Changning District, Shanghai
Campinas, Sao Paulo, Brazil
200335 China
Phone: +55 19 2103 2860
Phone +86 21 22181111
Fax: +55 19 2103 2862
Fax: +86 21 22182398
latam.boschsecurity@bosch.com
www.boschsecurity.com.cn
www.boschsecurity.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising