Turny HD Turny Orbit Autoadapt Seat lift

Turny HD Turny Orbit Autoadapt Seat lift
Turny
Autoadapt
Seat lift
Turny HD
SV
EN
DE
FR
ES
IT
4
22
40
58
76
94
Turny Orbit
Bruksanvisning
User manual
Gebrauchsanweisung
Instructions d’utilisation
Instrucciones de uso
Istruzioni per l’uso
Thank you for choosing a
Turny
from Autoadapt!
Autoadapt
TI
V
EH
TA
E
Once again, thank you for placing your confidence in our products!
SAF
If you have any questions about your adaptation, please feel free to contact your
installation engineer. If you wish to share your opinions about the product or the
company with us, you can register them on www.autoadapt.com/register. That way,
you will be helping us to become a better supplier.
ON
Thank you for choosing us as the supplier of your car adaptation. This product is
designed to make it easier for you to drive your car, and we have focused parti-cularly
on safety, quality and functionality. The following manual is an integral and important
part of the product, providing you with information on how to achieve maximum
performance and safe operation. Keep the manual in a safe place so that you can
refer to it when necessary.
ICLE ADA
P
Safe vehicle adaptation solutions
For your safety Autoadapt products are
designed and tested according to current
directives and standards.
Getting seated
Turny
23
Safety
24
Safety measures
26
28
Hand control
Manoeuvring outwards and inwards
30
32
Raise Turny Orbit/HD
Rotate the Turny Orbit inwards
Emergency-mode operation
Care instructions
34
Troubleshooting
35
Technical specification
37
Introduction for users
38
Servicing information and “Declaration of conformity” at the end of the manual.
Index
EN
Operation
24
Turny
Getting seated
Safety
Safety measures
Max user weight is 150 kg.
Ensure that the car is standing on a level surface and that the parking
brake is set before using Turny.
Ensure that nothing can fasten or get caught when manoeuvring Turny.
Make sure that the cable to the hand control hangs freely to avoid it
becoming damaged.
If possible, recline the back support to minimise the risk of the user’s head
bumping against the door opening whilst being moved.
Ensure the hand control’s green LED light is constantly lit before setting off.
This indicates the Turny is in a safe position for driving.
Any modifications, adjustments or repairs to a Turny may only be performed by authorised technicians.
Getting seated
Turny
25
Safety
EN
Getting up
Turny can be used as a lifting aid for the user, if at the same a
helper carefully moves the seat upwards, see illustration.
Transferring to and from wheelchair
A transfer between car seat and wheelchair, or vice versa,
becomes easier if the transfer is made from a higher to a
lower position. By adjusting the Turny’s height an optimal
transfer position can be achieved.
26
Turny
Getting seated
Operation
Hand control
OUT /
In order to rotate outwards and lower Orbit, or lower HD, keep the left-hand button in. To interrupt the movement, release the button.
OUT
IN
IN /
OUT
IN
In order to raise and rotate Orbit inwards, or raise HD, keep the right-hand button
in. To interrupt the movement, release the button.
When the green LED is constantly lit, Turny is in a safe position for driving.
When the green LED is blinking, Turny is not in a safe position for driving.
•
The standard model Turny is supplied with a cable connected hand control unit.
Turny can be manoeuvred via a wireless hand control unit, available as an optional
extra.
•
For safety reasons the Turny can only be manoeuvred when the vehicle is
stopped and/or the door is open.
•
When not in use place the hand control in its holder.
Hand control messages during normal operation.
Message
Cause
No diode lit
The vehicle's engine is switched on and/or the door is closed. Turny cannot be
manoeuvred.
Green LED blinks slowly
Energy-saving mode.
Green LED lit
Rotated inwards to end position. Turny is in a safe position for driving.
Green LED blinks
Not rotated inwards to end position. Turny is not in a safe position for driving.
Red LED lit
Green LED blinks
End position reached and cannot be further lowered.
Red LED lit
Green LED blinks slowly
Has reached the end position and is in energy saving mode.
If Turny is overloaded or hits an obstacle, the hand control’s red diode will
blink, see chapter ”Troubleshooting”.
Turny
27
EN
Operation
Getting seated
28
Getting seated
Turny
Manoeuvring outwards and inwards
Rotate outwards
OUT
IN
Lower
Turny Orbit
OUT
OUT
IN
OUT
IN
Turny HD
OUT
IN
Grip the seat. Pull the release lever upwards and
rotate the seat outwards to its locked end position.
OUT
IN
Lower the seat to the desired height.
IN
Getting seated
29
Rotate inwards
Turny Orbit
OUT
IN
OUT
IN
Turny HD
If possible, recline the back support to minimise
the risk of the user’s head bumping against the
door opening whilst being moved.
Grip the seat. Pull the release lever upwards and
rotate the seat inwards to its locked end position.
When the green LED is constantly lit, Turny is in a safe
position for driving.
EN
Operation
Raise
Turny
30
Turny
Getting seated
Emergency-mode operation
Raise Turny Orbit/HD
Remove the fuse, positioned close to the car’s battery, before starting emergency-mode operation.
Contact your installer for overhaul. Any faults must
first be rectified before reusing Turny.
Option A, stop at least 2 cm before the end position to prevent damage to the motor.
2 cm
Option A - easy but slow
Take out the crank affixed to the plate behind the back support.
Insert the crank behind the hexagonal keyhole at the Turny’s rear
section and fully crank the seat in.
Option B - difficult but quick
Remove the two cotter pins behind the seat. Lift and then push
the chair all the way in. Be firm but careful.
Turny
31
EN
Emergency-mode operation
Getting seated
32
Turny
Getting seated
Rotate the Turny Orbit inwards
Remove the fuse, positioned close to the car’s battery, before starting emergency-mode operation.
Contact your installer for overhaul. Any faults must
first be rectified before reusing Turny.
1
Remove the locking pin to release the yellow lever at
the front of Turny.
2
Depress and push the lever to the side to release the
seat. Push the lever to the right on a right model and
to the left on a left model.
3
Swivel the seat all the way in. Now push the lever back
to its original position and replace the locking pin.
Turny
33
EN
Emergency-mode operation
Getting seated
34
Turny
Getting seated
Care instructions
If necessary.................................................................
Carefully vacuum the Turny. Do not use any liquids.
Once a year ...............................................................
Contact your installer to book the annual service: see the end of the manual.
•
•
The product documentation must always be available during inspection of the vehicle.
Always contact your dealer for disassembly.
Getting seated
Turny
35
Troubleshooting
Hand control error messages
No diode lit
Cause
Actions
Switch off ignition and check that
fuse(s) and cable(s) are intact. For
further help contact your installer.
Check for obstacle(s) in the way.
Reactive Turny.
Contact your installation engineer.
1
1 Red blink
2
2 Red blinks
The vehicle's engine is switched on and/
or the door is closed. Power supply
interrupted.
Power surge or pinch protection. Turny
stops with small amount of reverse
movement.
Potentiometer broken or disconnected.
3
3 Red blinks
Potentiometer/lift motor not moving.
4
4 Red blinks
5
6
Faulty switch for inwards- or outwardsrotated position. Both affected
simultaneously.
5 Red blinks
Upper limit position broken, constant
fault.
6 Red blinks
Max limit for manoeuvring has been
reached, 180 seconds.
Alternating Red and Green Upper limit position not affected, and max
LEDs
outwards-rotation not affected. Turny
cannot be manoeuvred.
Contact your installation engineer.
Contact your installation engineer.
Contact your installation engineer.
Contact your installation engineer.
Contact your installation engineer.
EN
Troubleshooting
Message
36
Turny
Getting seated
Please contact your installation engineer if you require further assistance or need to ask questions
about warranty. We recommend keeping the following information to hand at all times:
Model /
Serial number /
Year of manufacture /
Date of purchase /
Notes /
Contact details for the installation engineer /
Getting seated
Turny
37
Technical specification
Technical data
EN
Technical specification
From above, rotated out towards the right.
The length and width dimensions show Turny without
covers or accessories.
A
590 mm
165 mm
B
475 mm
From the back, rotated out
towards the right.
Length .................................................................................................... 590 mm
Width ...................................................................................................... 475 mm
Installation height, up to chair attachment ......................... 165 mm
Maximum user weight ....................................................................... 150 kg
Voltage .....................................................................................................12 VDC
Fuse...................................................................................................................30 A
Power consumption at maximum load ........................................ 18 A
Power consumption in standby mode................... approx. 15 mA
A / Rotation angle
HD ........................................................................................................ 78° - 105°
Orbit ...................................................................................................... 68° - 97°
B / Vertical movement
HD/Orbit 300 ....................................................................................300 mm
HD/Orbit 395..................................................................................... 395 mm
HD/Orbit 4801 ..................................................................................480 mm
38
Turny
Getting seated
Introduction for users
Autoadapt would like you, as a user, to feel secure and comfortable with your new
product. For that reason, it is your installer’s duty to go through the following with
you /
•
•
•
Safety
Operation
Emergency-mode operation
If any questions about the product should come up later on, you are of course very
welcome to contact your installation engineer again.
The above chapters have been gone through /
Date /
Name of dealer /
Signature, installation engineer
Signature, user
Turny
39
EN
Introduction for users
Getting seated
Declaration of conformity
Manufacturer /
Autoadapt AB
Åkerivägen 7, 443 61 Stenkullen
Sweden
Phone: +46 302 254 00
E-mail: support @ autoadapt.se
www.autoadapt.com
Declares that the product /
Turny HD/Orbit, model 300/395/480,
incl mounting console made by
Autoadapt
Conforms to following Laws,
Directives and Standards /
EN 292-2/A1
72/245/EEC, 74/60/EEC, 77/541/EEC, ISO 7637-1, 74/408/EEC, 76/115/EEC2005/41 EC, EN 12182, EN 55022, 93/42/EEC, 95/28/EC, 89/392/EEC. ECE R-10,
ECE R-14, ECE R-17, ECE R-21, FMVSS 201, 207, 208, 209, 210, 225, 302.
EN 60204-1, EN 61000-4-2:1995, ISO 3795, 2006/28/EC, 2006/42/EC
2007/47/EEC, LVFS 2009:18
We relate to comparing practical tests at Swedish National Testing and
Research Institute with reference number 95H11227,
97H30472, 97H30473, 98H30540, 98H30542, 99F52587,
P101522B, P105622, F1211612, P005826A, P203878,
MKp P205854D, BMf P300994C, BMf P300994D, BMf P300994E, F121612.
F903889,F916233,P806081,P901080,P603707,F609435, P906398
The tests performed in USA are MGA C00Q6-112.1,
MGA C00S3-061, MGA C01S3-002.
The original anchor points of the OEM-seat must be used.
Autoadapt AB, Stenkullen 2013-08-01
Håkan Sandberg, CEO
1976
ISO/IEC 17025
Accredited by SWEDAC as testing laboratory in accordance with ISO/IEC 17025:2005
Quality system certified in accordance with ISO 9001:2008
Illustrations, descriptions and specifications in the user manual are based on current product information.
Autoadapt reserves the right to make alterations without previous notice.
© 2014 Autoadapt AB
do what so many take for granted;
drive to work, pop down to the
shops, drop in on friends or go on
a great driving holiday. It is with
great pride we design and manufacture solutions that people from
all over the world put their trust
in every day.
To help you find the solution to suit your
needs, simply look at the corresponding
area of expertise at autoadapt.com
GETTING SEATED
WHEELCHAIR LIFTS
INDEPENDENT DRIVING
AUTOADAPT AB
AUTOADAPT UK LTD
Åkerivägen
7
AUTOADAPT
AB
S-443 61 Stenkullen
Åkerivägen
7
Sweden
S-443 61
Stenkullen
Phone:
+46
302 254 00
Swedeninfo@autoadapt.se
E-mail:
Phone: +46 302 254 00
E-mail: info@autoadapt.com
Unit
1, Windsor Industrial
Estate
AUTOADAPT
UK LTD
Rupert Street
Unit 1, Birmingham
Windsor Industrial
Aston,
B7 4PR,Estate
UK
Rupert
Street
Phone: +44 121 33 35 170
Aston, info@autoadapt.co.uk
Birmingham B7 4PR, UK
E-mail:
Phone: +44 121 33 35 170
E-mail: info@autoadapt.com
LIFTING AND STOWING
WHEELCHAIR RESTRAINTS
www.autoadapt.com
facebook.com/autoadapt
www.autoadapt.com
twitter.com/autoadapt
facebook.com/autoadapt
twitter.com/autoadapt
000000-0
428298-3
2014/062013/00
AT AUTOADAPT WE help people
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising