04/DEC/CT C3 Manual FINAL
Instruction Manual
US PAT:
6,824,069
6,786,421
www.climatouch.com
Models:
CT03TS21
CTO3TS32
CTO3TS32H
AED Electronics Inc.
5758 Royalmount Avenue
Montreal, Quebec,Canada
H4P 1K5
Technical Support:
1-866-90TOUCH
(1-866-908-6824)
514-737-4187
Dear Customer,
Thank you for purchasing a Climatouch™ thermostat, the most innovative thermostat in the world.
Did you know that your Climatouch™ thermostat
can also accurately display outdoor temperature?
To enable this convenient feature you need an
optional outdoor UHF temperature transmitter.
There is no need for any additional installation or
set-up. Simply fit the the transmitter unit with batteries and place it outdoors. Your Climatouch™
thermostat will start displaying accurate outdoor
temperature immediately.
Ask your installer for an optional outdoor
UHF temperature transmitter today!
UHF TEMPERATURE TRANSMITTER PART NUMBER :
217S31
www.climatouch.com
Mounting Climatouch™ to the wall
1.
Make sure to turn off the power supply located at the
electrical service panel. All heating and cooling units
should be OFF.
2. Remove the cover plate by pulling up the cover from the
left or right side only.
3. Align the Climatouch™ unit to the wall.
4. Mark the four locations for drilling the 3/16" holes required
for the plastic screw anchors.
5. Remove the thermostat and drill the four 3/16" holes
in these locations.
6. Insert the plastic gyproc screw anchors and tighten them
securely.
7. Make the appropriate wire connections based on the specifications of the household HVAC unit(s). Please refer to Wiring
Table to determine the appropriate wire connections.
8. Securely mount the Climatouch™ unit to the wall with
the four supplied screws.
9. Fit the cover plate back by clipping one side first (left
or right) and than push down on the opposite side.
10. Turn on the electricity at the electrical service panel.
C
R
Y2
O/B/W
W2
G
Y1
Dh-H
Terminals
Power Supply Common
24VAC Power Supply
See Wiring Table
heat or cool reverse valve - the default is energized
in COOL mode.
See Manufacturer's Technical Settings to reverse
(if necessary) the logical orientation of contact Ob.
Furnace
Fan
Compressor
Humidity model only.
24 VAC Class 2 MAX 4A
NOTE (Humidity model only)
HUMIDIFY feature controls the H relay in the HUMIDIFY
mode when there is a demand for humidifying. DH
relay may control a variable speed fan in DEHUMIDIFY
mode. DH relay is universally configurable in
“Advanced Settings” - Page 6.
Wiring Table
Configuration
Y1
Y2
AC
AC1
AC2
W2
OB/W
R C G
Cooling Only
Air Conditioner
2Air Conditioner
Furn. Off
Furn. Off
x
x
x
x
x
x
El.Furn2*
El.Furn2*
Gas2*
Oil2*
Gas2
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
OB
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Gas1
El.Furn1
El.Furn1
Gas1
Oil1
El.Furn
Gas
Oil
Gas2
El.Furn2
El.Furn2
Gas2
Oil2
OB
OB
OB
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
OB
x
x
x
OB
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Heating Only
No Compressor
No Compressor
No Compressor
No Compressor
No Compressor
Electrical Furn.
Emg. El. Furn.
Gas
Oil
2 Stage Gas
Emg.El.Furn
El.Furn
El.Furn
Gas
Oil
Gas1
* if there is another furnace, then connect it to OB/W relay.
1 Stage Cooling, 1 Stage Heating
Heat Pump
Air Conditioner
Air Conditioner
Air Conditioner
Air Conditioner
Furn. Off
Electrical Furn.
Emg. El. Furn.
Gas
Oil
HP
AC
AC
AC
AC
Emg. El.Furn
El.Furn
El.Furn
Gas
Oil
1 Stage Cooling, 2 Stage Heating
Air Conditioner
Air Conditioner
Air Conditioner
Air Conditioner
Air Conditioner
Heat Pump
Heat Pump
Heat Pump
2 Stage Gas
Electrical Furn.
Emg. El. Furn.
Gas
Oil
Electrical Furn.
Gas
Oil
AC
AC
AC
AC
AC
HP
HP
HP
Emg. El.Furn
1 Stage Cooling, 3 Stage Heating
Heat Pump
2 Stage Gas
HP
Gas2
Gas1
HP
AC1
AC1
AC1
AC
AC2
AC2
AC2
El.Furn
Gas
Oil
HP
HP
HP
HP1
AC1
AC1
AC1
AC1
AC
AC
AC
HP2
AC2
AC2
AC2
AC2
El.Furn1
Gas1
Oil1
Gas1
OB
OB
OB
OB
El.Furn2
Gas2
Oil2
Gas2
HP1
HP1
HP1
HP2
HP2
HP2
Gas
Oil
El. Furn
OB
OB
OB
2 Stage Cooling, 1 Stage Heating
HP /AC
2Air Conditioner
2Air Conditioner
2Air Conditioner
Furn. Off
Electrical Furn.
Gas
Oil
2 Stage Cooling, 2 Stage Heating
HP /AC
HP /AC
HP /AC
2Heat Pump
2Air Conditioner
2Air Conditioner
2Air Conditioner
2Air Conditioner
Electrical Furn.
Gas
Oil
Furn. Off
Electrical Furn.
Gas
Oil
2 stage Gas
El.Furn
Gas
Oil
2 stage Cooling, 3 stage heating
2Heat Pump
2Heat Pump
2Heat Pump
Gas
Oil
Electrical Furn.
HOME PAGE
To return to the Home Page, simply touch
9
icon at any time!
2
4
3
5
8
6
7
1
10
12
1
2
3
4
5
6
Room Temperature; to change ºF/ºC, go to 35.
Outdoor Temperature (ºF/ºC)2
Relative Room Humidity (%)1; to change set point, go to 17.
Thermostat Control Mode; to change, go to 19.
Temperature Control Mode; to change, go to 18.
Fan Operation Mode; to change, go to 20.
11
13
7
8
9
10
11
12
13
Fan Operation Indicator; to change, go to 20.
Vacation Mode Indicator; to change, go to 28.
Security On Indicator; to change, go to 36.
Heating set point; to change, go to 16.
Cooling set point; to change, go to 16.
Date (Month/Day/Year); to change, go to 24.
Time; to change, go to 24.
CONTROL PAGE
To access the Control Page, simply touch the Home Page Screen…anywhere!
21
19
22
18
13
15
17
20
23
*
14 Current Room Temperature.
15 Current Room Humidity1.
16 Heat and Cool temperature set points; to change, raise
or lower set point as desired. In “Auto” mode touch
* Heat/Cool button (Heat or Cool will flash once selected),
then raise or lower set points as desired.
17 Humidify/Dehumidify set point1; to change, raise or lower
as desired.
18 Temperature Control Mode; select between Heat / Cool
/ Auto / Emergency Heat.
16
19 Thermostat Operation Mode: Select between “Run
Program” mode (for details, see 25 ) or “Hold
Temperature” mode.
20 Fan Operation Mode: select between Fan Automatic /
Fan Continuously On / Fan Intermittently On.
Note: to save energy, select Fan Intermittent (runs fan
for 10 minutes every 1/2 hour).
21 Displays Installer Message; to enter a message, go to 37
22 Return to Homepage.
23 Access the Menu Page.
MENU PAGE
To access the Menu Page, simply touch
from the Control Page.
24
32
25
28
26
29
27
30
31
24 Set Date and Time.
25 Program automatic temperature changes and fan mode
(“Run Program” mode) 4 events per day.
26 Displays system energy consumption and cost of running
system; to enter system consumption parameters, go to
34; otherwise, displays fan and compressor runtime.
27 Freezes the screen for 15 sec to allow the user to wipe
the screen with dampened cloth.
28 Turn “Vacation Mode” OFF or ON and set: Departure Date,
Arrival Date and temperature set point. (“Vacation Mode”
will BEGIN at 11PM on your departure date and END at
midnight on your arrival date).
29 Displays filter usage in days and resets filter timer.
30 Select either “Humidify” or “Dehumidify” mode1; to change
Humidify / Dehumidify set point, go to 17.
31 Set Screen Options:
Daylight Time (ON/OFF): activate only if you are located
in a “Daylight Savings Time” zone.
Reverse: Select between dark background (ON) or light
background (OFF)
Night Reverse: Select between ON: Automatically reverses screen background for comfortable viewing at night
(from 9PM to 6AM) OFF: screen background determined
by “Reverse” function setting.
Contrast: set screen contrast from 1-11.
32 To access “Advanced Settings”, hold finger 5 seconds on icon.
ADVANCED SETTINGS: Page 1
33
36
34
ADVANCED SETTINGS: Page 2
38
40
39
41
35
37
33 Turn “Filter Monitor” ON or OFF; if ON enter the filter
replacement interval.
34 Enter HVAC system consumption parameters rounded
off to kW; see 26 (Typically: Fan 1kW; Heat Pump
1kW/ton; Furnace 5-30 kW, 7-9¢/kW)
35 Change thermostat temperature display units (ºF or ºC).
36 Turn “Security” ON or OFF (Default Security PIN = 1111)
and select the security level:
Partial Lock: User has can only change temperature set
point(s) without a password.
Full Lock: User must enter PIN to change any setting.
37 Enter “Installer Message” (up to 42 characters) to
appear at programmable intervals, see 21.
Please note that inadvertently modifying
Compressor and Furnace settings, may
seriously degrade system performance.
38 Select system heating and/or cooling equipment:
Heat Pump, 2-stage Heat Pump, Air Conditioning, No
Compressor - see Wiring Table.
39 Select the system Furnace Type:
Furnace Off (No Furnace), Electric Furnace, Emergency
Electrical Furnace (additional electric furnace which will
come on in emergency mode in conjunction with electric
furnace), Gas Furnace, Oil Furnace, and 2-stage Gas
Furnace; see Wiring Table.
40 Set maximum compressor cycles per hour.
41 Set Minimum difference between auto mode heat and
cool temperature set points. See 18.
ADVANCED SETTINGS: Page 3
ADVANCED SETTINGS: Page 4
42
43
46
44
45
42
43
44
45
Set temperature difference between temperature set point
and actual temperature reading before 1st stage heating
or cooling is initiated.
Set temperature difference between 1st stage initiation
(42) and 2nd stage heating or cooling initiation.
Set temperature difference between 2nd stage initiation
(43) and 3rd stage heating or cooling initiation.
NOTE: Number of stages depends on your system; see
38 & 39.
Reverses the Heat Pump OB Valve contact ; (manufacturer dependant)
46
Specify X minutes for which stage 1 will function until
stage 2 is activated to help raise (or cool) temperature
(if the temperature set point is not reached). This function
avoids excess compressor wear in the case where the
necessary temperature set point is not met (see 42, 43
& 44). Set to “00” to disable.
ADVANCED SETTINGS: Page 5
ADVANCED SETTINGS: Page 61
47
48
49
50
51
47 HP “ON” when Furnace On: Heat Pump and Furnace can
operate together when 2nd stage furnace is required.
HP “OFF” when Furnace On: turns off the Heat Pump when
the furnace is On (required on some gas or oil furnaces).
49
50
51
48
ON: fan runs when there is an independent demand to
humidify;
OFF: fan only runs when there is a demand to humidify
while heating or cooling.
ON: fan runs when there is an independent demand to
dehumidify;
OFF: fan only runs when there is a demand to dehumidify
while cooling.
ON, DH relay is normally closed when relative humidity
is above DH set point.
OFF, DH relay is normally open when relative humidity
is above DH set point.
ON: thermostat will turn off the air conditioning if either
the dehumidify set point or the temperature set point is
reached, whichever comes first, both DH relay and
compressor will turn off.
OFF: DH relay is independent of compressor activity (DH
becomes a spare and can be used for a variable speed
fan or separate dehumidifier or air exchanger)
ADVANCED SETTINGS: Page 7
52
53
52 Humidity calibration offset - allows for fine-tuning of the
humidity sensor.
53 Temperature calibration offset - allows for fine-tuning
of the temperature sensor (use an accurate thermometer
to calibrate if necessary).
1
2
Humidity model only.
Requires wireless temperature transmitter.
Simple Thermostat Mode
Climatouch can also function as a non-programable
thermostat after it has been configured.
Simple Mode has the following basic features:
Temperature Control Modes:
Fan Operation Modes:
To enable “Simple Mode”, press the reset button (take off the
thermostat faceplate and press the reset button located in the
bottom right-hand corner). The message “Touch for simple
thermostat” will appear. Touch the screen, and Climatouch
becomes a simplified non-programmable thermostat.
* Please note that when changing to Simple Mode, you will not
lose any of the settings you have previously entered in the
“Programmable Mode”.
* To revert back to the Programmable Climatouch Thermostat,
simply press the reset button and touch the screen when the
message “Touch for Programmable Thermostat” appears.
Troubleshooting
Touch screen buttons do not function properly.
Remove cover, press the reset button located in the bottom
left corner then accurately touch 3 target centers on the
screen when prompted.
Air Conditioning does not turn on even when room
temperature is higher then the temperature set
point set point (Humidity models only).
DHCONTROLCOMP is turned ON and dehumidify set point
has been reached. This will cause air conditioning to turn
off. Lower dehumidify set point or turn off “DH Controls
Compressor” feature (see “Advanced Settings” Page 6).
Air conditioning turns on in HEAT mode and heating
turns on in COOL mode.
Reverse the OB valve (see “Advanced Settings” Page 3).
PARTIAL LOCK and FULL LOCK do not function.
You must not touch the screen for 1 minute for
Climatouch™ to automatically lock
Thermostat appears normal until the screen
becomes blank when the compressor or heating
system turn on.
You need to connect the “C” wire. 4 wire system will not
function unless the heat and compressor contactors can
supply enough current to power the thermostat with only
4 wires, if you cannot hook up the “C” wire another possible
solution is to connect two 100 ohm 10 watt resistors in
the HVAC room, one between Y and C, and the second
one between W2 and C.
I forgot my PIN and cannot unlock the thermostat.
Remove the cover plate, press the reset button located in
the bottom right corner, as soon as the message “touch
to reset password” appears touch the screen, your PIN
will be erased and the thermostat will unlock.
LIMITED WARRANTY
Hardware
AED Electronics Inc. (“AED”) warrants the original end user (“Customer”)
that new Climatouch branded products will be free from defects in workmanship and materials, under normal use, for two (2) years from the original purchase date.
Software
AED warrants to Customer that the Climatouch thermostat software will perform in substantial conformance to its program specifications for a period of
two (2) years from the date of the original purchase.
Exclusions
This warranty excludes (1) physical damage to the surface of the product,
including cracks or scratches on the touch-screen or outside casing; (2)
damage caused by misuse, neglect, improper installation, unauthorized
attempts to open, repair, or modify the product, or any other cause beyond
the range of intended use; (3) damage caused by accident, fire, power
changes, other hazard, or Acts of God; or (4) use of the product with any
device if such device causes the problem.
Exclusive Remedies
Should a covered defect occur during the warranty period and Customer
notifies AED, Customer’s sole and exclusive remedy will be, at AED’s sole
option and expense, to repair or replace the product. Replacement products
or parts may be new or reconditioned or a comparable version of the defective item. AED warrants any replaced product or part for a period of ninety
(90) days from shipment, or through the end of the original warranty,
whichever is longer.
Obtaining Warranty Service
Customer must contact and return product to a local AED product dealer or
installer within the applicable warranty period to obtain warranty service.
Dated proof of original purchase will be required. AED will not be responsible for Customer’s memory data contained in, stored on, or integrated with
any products returned to AED for repair, whether under warranty or not.
Warranty Exclusive
THE FORGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU
OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE,
CORRESPONDENCE WITH DESCRIPTION, AND NON-INFRINGEMENT, ALL OF
WHICH ARE EXPRESSLY DISCLAIMED BY AED AND ITS SUPPLIERS.
Disclaimer
NEITHER AED NOR ITS SUPPLIERS SHALL BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR
FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE OR
USE OF THIS PRODUCT, WHETHER BASED IN CONTRACT, TORT (INCLUDING
NEGLIGENCE) OR ANY OTHER THEORY, EVEN IF AED HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. AED’S ENTIRE LIABILITY SHALL BE
LIMITED TO REPLACEMENT OR REPAIR OF THE PRODUCT.
FCC Statement
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC
RULES. OPERATION IS SUBJECT TO THE FOLLOWING
TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST
ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
AED Electronics Inc.
5758 Royalmount Avenue
Montreal, Quebec, Canada
H4P 1K5
Technical Support:
1-866-90TOUCH (1-866-908-6824)
514-737-4187
www.climatouch.com
Printed in Canada
B4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising