Quick Installation Guide

Quick Installation Guide
Quick Installation Guide
Super 8 Roll Film Digitizer
COMPONENTS
Front (Figure 1):
1) Supply Reel (Arm)
2) Take-up Reel (Arm)
3) Feed Sprocket
4) Forward Button
2) Take-up Reel (Arm)
1) Supply Reel (Arm)
• Press briefly (1 sec)—feeding frame one by one,
• Press and hold (more then 3 seconds)--- Continuously
feeds the frames
5) Stop Button
6) Rewind Button
3) Up Feed Sprocket
4) Forward Button
• Press briefly (1 sec)— feeding frame one by one,
• Press and hold (more then 3 seconds) --Continuously feeds the frames
7) Film Rollers
8) Film Cleaner
9) Power Button
3) Down Feed Sprocket
5) Stop Button
6) Rewind Button
7) Film Rollers
8) Film Cleaner
Figure 1
9) Power Button
Back (Figure 2):
10) DC power
11) USB 2.0 port
10) DC power
11) USB 2.0 port
Figure 2
3
Super 8 scanner Quick guide
Before Installing Scanner
Check your Super 8 Film Reel, Film and Hard Disk
Space
Film Reel :
Super 8 Scanner support 1”~8” standard Super 8
film reel
Film:
1. Please make sure your film is smooth, if not
please use cutter to repair and maintain to
smooth (Fig 1, 2)
2. If your film is splicing, please check as below
list before you insert film
• splicing parts and film hold are smooth
• The cement is fully dry
or will damage super 8 scanner
3. Please use special solvent with Super 8 Scanner
or will damage your film.
х
х
○
х
○
Fig. 1
х
Fig. 2
Hard Disk Space:
Reel Type
50 feet
(15 meters)
200 feet
(60 meters)
300 feet
(90 meters)
400 feet
(120 meters)
600 feet
(180meters)
Super 8 Film at
18 frames
/second
Super 8 Film at
24frames
/second
3.5 min
2.5 min
13 min
10 min
20 min
15 min
26 min
20 min
40 min
30 min
Hard Disk Space
1 GB (0.45 GB
for movie)
4 GB (1.8 GB for
movie)
6 GB (2.7 GB for
movie)
8 GB (3.6 GB For
movie)
12 GB (5.4 GB
movie)
Super 8 scanner Quick guide
Calibration Light Source (First time use)
1
4
Open the Case
2
6
Wait for LED light to turn Orange
click “Calibration” button
5
Turn on Power
3
Activate the
CyberView S8
Software
7
After Finish Calibration
click “OK” button
Connect to USB to PC
Create a New Movie Plan
and click “Next” button
Super 8 scanner Quick guide
Install Super 8 Scanner
1
3
Open the Case
2
7
4
Install movie film reel to Supply
Reel Arm and Take-up Reel Arm
Open the Reel Arm
Turn on Power
Wait for LED light to turn Orange
8
5
Install film to Super 8 Scanner
(Please see “How to install film”)
6
Make Sure the Reel is
securely installed
Connect to USB to PC
9
Activate the
CyberView S8
Software
Start to Digitize Your
Super 8 Movie
Super 8 scanner Quick guide
How to install film to Super 8 Scanner
4
1
8
5
Click Stop Button
Turn on Power
2
Feeding film into Up Feed
Sprocket
6
Feed Direction
9
Film auto feeds out from
Down Feed Sprocket
Start to Digitize Your
Super 8 Movie
7
Film Hold
Press and hold Forward Button
Press the Forward Button until film
is rolling tight then press Stop
Button
Scroll film until a sufficient length
to Take-up Reel then press Stop
Button
Install movie film reel to Supply Reel
Arm and Take-up Reel Arm
3
Feeding film into the Film Rollers
Feeding film into the Take-up
Reel
Lock your film onto the Take-up
Reel
Push
Locked
Super 8 scanner Quick guide
How to clean your film with Super 8 Scanner
4
1
Turn on Power
2
Install movie film reel to Supply
Reel Arm and Take-up Reel Arm
3
Press and hold the Forward
Button
5
6
7
Open the cover of the
Film Cleaner
9
Feeding film into the Take-up Reel
Add cleaning solvent to
Wool Felt
Feed Film through the wool felt
8
10
Click Stop Button
Activate the
CyberView S8
Software
Click Clean
Button to start
cleaning your
film
CyberView S8 Software Quick guide
Installing the CyberView S8 Software
1. Install the CyberView S8
2. Connect the USB to the PC
3. Push the Power Button to turn the unit on
4. Install film to S8 Digitizer
5. Open the CyberView S8
Create a new movie
1.
2.
3.
4.
Choose “Create Your Movie Plan name”
Type the plan name
Choose the default export folder
Click the “Start Your Plan” to start digitizing
Continue an existing movie plan
1.
2.
3.
Choose “continue movie plan”
Browse to the existing folder and choose ”plan.ini “
Click the “Start Your Plan” to continue digitizing
CyberView S8 Software Quick guide
Preview Widow
Capture interface
1. Check the preview window
2. Click “up” and “down” to check your first
capture frame
3. Click “Capture” to start digitizing S8 movie
4. After you finish digitizing the S8 movie, the
software will auto stop capture (this is not the
5.
Frame Control button
Auto Brightness
Brightness
adjustment bar
Auto Contrast
last step in the process)
Click next to watch your movie
Capture Button
Calibration
Digitized frame counting
Relapsed time
CyberView S8 Software Quick guide
Preview Widow
Combine interface
1. Check the preview window
2. Choose your super 8 movie frame rate(18 or 24
frame rate/ sec)
3. Click apply button to preview digitized frames
4. Choose output size “1080p” or “720p”
5. Click “Combine” to transfer frame to movie
6. After finishing the movie transfer, you can click “see
your movie” to watch digitized super 8 movie
Output Size
Combine
Watch Video
Frame Rate
CyberView S8 Software Quick guide
Advanced Setting
More detail operation function, setting and troubleshooting please check user manual (in Cyberview
S8 CD) or go to reflecta website www.reflecta.de
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising