FireLock NXT™ Actuated Valve with Preaction Trim 30.82

FireLock NXT™ Actuated Valve with Preaction Trim 30.82
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
VNIIPO
MEA: 248-98-E
CSFM: 7770-0531-117
SERIES 769
With Preaction Trim
Grooved x Grooved
The patented Victaulic FireLock NXT Series 769 Preaction Valve controls the water supply
entry into the Preaction system piping and sprinklers. The Preaction System is n
­ ormally supervised with pressurized air or nitrogen in order to detect any leaks in the system. The Series
769 is a low differential, latched clapper valve that uses a unique direct acting d
­ iaphragm to
separate system water supplies from Preaction pipe sprinkler systems. The p
­ ositive latching
mechanism uses the supply water pressure from upstream (city side) of the main control valve
to hold the clapper shut. When the water pressure in the diaphragm chamber is released the
latch retracts from the clapper and the valve actuates. The low differential and unique latch
and actuator design of the valve allows the valve to be self-resetting; therefore it is not necessary to remove the cover. The low differential design is not subject to water columns.
FEATURES
Clapper
The valve allows the water to operate a water motor alarm and/or electric pressure alarms, which
continue until the flow of water stops.
The valve is rated to 300 psi/2065 kPa water working pressure and is factory tested hydrostatically to
600 psi/4135 kPa for sizes 1 1/2 – 8"/40 – 200 mm. Required air pressure is 13 psi/90 kPa. The Series
769 is available grooved x grooved. Standard grooved dimensions conform to ANSI/AWWA C606.
Latch
Victaulic Series 769 Preaction valves do NOT require a separate check valve in the preaction system
and feature a straight-through valve body design that provides superior flow and low-pressure drop.
The valve body is tapped with a special drain for a complete system. The valve has simple access to
all internal parts for easy maintenance. All internal parts are replaceable.
Diaphragm
Assembly
Seat
Clapper
Seal
NOTE: VALVE IS SHOWN
ABOVE IN THE
POSITION
Exaggerated
for“SET”
Clarity
Exaggerated for Clarity
NOTE: Valve
is shown in the “set” position
Maintenance and service can be performed from the installed position. The rubber clapper seal is
replaced easily without removing the clapper from the valve. The body is tapped for main drain and
all available trim configurations. The valve is painted inside and out to increase corrosion resistance.
The Victaulic FireLock NXT Series 769 Preaction valve trim includes an alarm test valve, which allows
testing of the alarm system without reducing the system pressure. The Series 769 Preaction Valve
must be located in an area maintained above 40°F (4°C), which is not subject to weather, freezing
temperatures, or physical damage.
NOTE: The bare value carries the LPCB and VdS approvals for deluge applications only. There is no
LPCB or VdS recognition of the preaction configurations.
JOB/OWNER
CONTRACTOR
ENGINEER
System No.___________________________
Submitted By_________________________
Spec Sect_____________ Para___________
Location_____________________________
Date________________________________
Approved____________________________
Date________________________________
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
REV_H
30.82_1
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
INSTALLATION OPTIONS
Pre-trimmed
The pre-trimmed valve comes completely assembled with all necessary trim components.
Vic®-Quick Riser
The Vic-Quick Riser comes completely pre-trimmed and includes a shut off valve (uses a Series 705
FireLock Butterfly valve – request publication 10.81; for 1 1/2 and 2"/40 and 50 mm sizes, the
Vic-Quick Riser comes with a Series 728 Ball Valve – request publication 10.17) for system shut off,
pre-set pressure switches, and a drain kit for ease of installation.
Series 745 FireLock Fire-Pac
The Fire-Pac is a completely pre-assembled fire protection valve that provides maximum service in
a minimal enclosed space. The unit includes a water supply shutoff valve, the sprinkler system fire
protection valve, alarm line pressure switches, air supervisory pressure switches, supervisory pump
switches, and digital pressure gauges that are easily viewed through a window in the cabinet door.
For complete Fire-Pac information request publication 30.23.
Optional accessories ship separately.
RELEASE MECHANISM OPTIONS
Non-Interlocked
Non-interlocked systems are designed so that either an event detection by the release mechanism or
loss of supervisory air in the sprinkler system will cause the valve to operate. When the valve operates, water will enter the sprinkler system and flow from any open sprinklers or other openings in the
system.
The pneumatic release system uses a supervisory pilot line to detect a release
event. When EITHER a pilot sprinkler or a system sprinkler operates, the water in the diaphragm
chamber is released and the valve operates. If the pilot sprinkler activates and a system sprinkler
does not operate, water will fill the sprinkler system, alarms will be activated and the Victaulic Series
769 Actuated Valve will act as an Alarm Check Valve. If the valve is actuated by the activation or
damage of a sprinkler, water will enter the system and flow from any open sprinklers. Alarms will activate due to water entering the intermediate chamber of the valve.
The Victaulic Electric Release System uses an electric solenoid valve,
approved electric panel and a compatible detection system. When EITHER an electric detection or a
system sprinkler operates, the water in the diaphragm chamber is released and the valve operates. If
there is an electric detection and a system sprinkler does not operate, water will fill the sprinkler system, alarms will be activated and the Victaulic Series 769 Actuated Valve will act as an Alarm Check
Valve. If the valve is actuated by the activation or damage of a sprinkler system sprinkler, water will
enter the system and flow from any open sprinklers. Alarms will activate due to water entering the
intermediate chamber of the valve.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
30.82_2
REV_H
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
SYSTEM DESCRIPTION
Single Interlocked
Single interlocked systems are designed so that only an event detection by the release mechanism
will cause the valve to operate. When the valve operates water will enter the sprinkler system and
flow from any open sprinklers or other openings in the system.
The pneumatic release system uses a supervisory pilot line to detect a release
event. Only when a pilot sprinkler operates will the water in the diaphragm chamber be released and
the valve operate. Pneumatic pressure is maintained in the sprinkler system only for supervisory
purposes and a low pressure alarm is installed in the sprinkler system in order to detect any leaks in
the system. If the pilot sprinkler activates and a system sprinkler does not operate, water will fill the
sprinkler system, alarms will be activated and the Victaulic Series 769 Actuated Valve will act as an
Alarm Check Valve. If a system sprinkler is damaged or activates and there is no release mechanism
detection the low pressure alarm in the system will activate but no water will flow until there is a
release detection.
The Victaulic Electric Release System uses an electric solenoid valve, approved
electric panel and a compatible detection system. Only when a release system event occurs, will the
water in the diaphragm chamber be released and the valve operate. Pneumatic pressure is maintained in the sprinkler system only for supervisory purposes and a low pressure alarm is installed in
the sprinkler system in order to detect any leaks in the system. If there is an electric release activation and a sprinkler system sprinkler does not operate, the valve will operate and water will fill the
sprinkler system, alarms will be activated and the Victaulic Series 769 Actuated Valve will act as an
Alarm Check Valve. If a system sprinkler is damaged or activates and there is no release mechanism
detection, the low pressure alarm in the system will activate but the valve will not operate and no
water will flow until there is a release detection.
Double Interlocked
Double interlocked systems are designed so that the valve will actuate only in the event of multiple
fire detections by the release mechanisms. If a single release event occurs alarms will sound but the
valve will not operate and water will not flow until a second release event is detected. Double interlocked systems are commonly used in refrigerated systems and in systems where water entering the
sprinkler system is critical as well as when accidental discharge of water is critical.
The electric/pneumatic preaction system uses both an electric release
system, (composed of an approved solenoid valve, electric panel and an appropriate sensor), and
pneumatically pressurized sprinkler system. The Victaulic Series 769 Actuated Valve will activate
ONLY when there is a pressure loss in the sprinkler system AND the electric detection of a release
event. In the event of a loss of pressure in the sprinkler system without an electric detection the valve
will not actuate until a second release event is detected. In this way if there is accidental damage to
the sprinkler system no water will flow. Additionally, if there is an electric detection and no pressure
loss in the sprinkler system the valve will not actuate. Alarms will activate in both cases alerting the
user of a detection condition.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
REV_H
30.82_3
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
SYSTEM DESCRIPTION
Electric (Electric-Pneumatic/Electric): The electric/pneumatic/electric release uses two electric
detection devices, a fire detection device and a low pressure switch installed in the sprinkler system.
Both electric detection devices are wired into an approved control panel in a “cross-zoned” configuration. The electric control panel controls a solenoid valve piped to the Victaulic Series 769 Actuated
Valve piston. In the event of a fire detection device activation and no pressure loss in the sprinkler
system the control panel will not trigger the solenoid valve and the valve will not actuate. If there is a
loss of pressure in the sprinkler system due to damage or a sprinkler activating and no fire detection
the control panel will not trigger the solenoid and the valve will not actuate. The valve will actuate
ONLY when BOTH a fire detection event and loss of system pressure occurs. When BOTH signals are
received by the control panel the panel triggers the solenoid valve. This allows the water supply pressure in the Series 769 diaphragm chamber to be released and the valve will actuate allowing water
into the system.
The pneumatic/pneumatic system uses one Series 798 Double
Pneumatic Actuator to control the Series 769 Actuated Valve. The system control valve will operate
only when there are sprinklers activated in both the pilot line and the sprinkler system. If a sprinkler
is activated in either the pilot line or the sprinkler system (without an accompanying open sprinkler in
the other system) the system control valve will not operate. Since the pneumatic/pneumatic system
uses two separate pneumatic detections, the need for an electric release panel is eliminated. In all
cases, an open sprinkler will cause low-pressure supervisory alarm. Note: All Series 769 valves are
approved and listed for double interlock pneumatic – electric with the Series 767. It is also approved
for double interlock and pneumatic/pneumatic double interlock configurations with the Series 798.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
30.82_4
REV_H
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
DIMENSIONS FOR TRIM WITH
SERIES 776 LOW-PRESSURE ACTUATORS
THE 4 INCH/114.3 MM CONFIGURATION IS SHOWN BELOW
1 ½ – 2 INCH/48.3 – 60.3 MM CONFIGURATIONS CONTAIN ¾ INCH/19 MM DRAIN VALVES.
2 ½ – 3 INCH/73.0 – 88.9 MM CONFIGURATIONS CONTAIN 1 ¼ INCH/31 MM DRAIN VALVES.
4 – 8 INCH/114.3 – 219.1 MM CONFIGURATIONS CONTAIN 2 INCH/50 MM DRAIN VALVES.
G
E
F
D
*B1
*D1
B
A
*A1
J
H
K
C
Full Open
Size
*E1
Aprx. Weight Ea.
lbs/kg
Dimensions – inches/mm
Nominal Size
Inches/
mm
Actual Outside
Diameter
Inches/
mm
A
A1*
B
B1*
C
D
D1*
E
E1*
F
G
H
J
K
Without
Trim
With
Trim
1½
40
1.900
48.3
9.00
228.60
16.43
417.32
28.25
717
40.50
1028
13.75
349
16.00
406
—
5.25
133
8.50
215
9.50
241
22.25
565
3.04
77.21
9.17
232.91
6.98
177.29
16.7
7.6
43.0
19.5
2
50
2.375
60.3
9.00
228.60
16.43
417.32
28.25
717
40.50
1028
13.75
349
16.00
406
—
5.25
133
8.50
215
9.50
241
22.25
565
3.04
77.21
9.17
232.91
6.98
177.29
17.0
7.7
43.0
19.5
2½
65
2.875
73.0
12.61
320.29
16.50
419.10
32.25
819
44.25
1123
13.50
342
16.00
406
17.50
444
5.25
133
9.00
228
9.25
234
21.25
539
3.90
99.06
10.50
266.70
6.93
176.02
41.0
18.7
65.0
29.5
76.1 mm
3.000
76.1
12.61
320.29
16.50
419.10
32.25
819
44.25
1123
13.50
342
16.00
406
17.50
444
5.25
133
9.00
228
9.25
234
21.25
539
3.90
99.06
10.50
266.70
6.93
176.02
41.0
18.7
65.0
29.5
3
80
3.500
88.9
12.61
320.29
16.50
419.10
32.25
819
44.25
1123
13.50
342
16.00
406
17.50
444
5.25
133
9.00
228
9.25
234
21.25
539
3.90
99.06
10.50
266.70
6.93
176.02
41.0
18.7
65.0
29.5
4
100
4.500
114.3
15.03
381.76
19.78
502.41
33.25
844
45.50
1155
15.00
381
15.75
400
20.50
520
5.50
139
9.00
228
10.75
273
20.75
527
6.25
158.75
9.62
244.34
8.46
214.88
59.0
26.7
95.0
43.0
165.1 mm
6.500
165.1
16.00
406.40
22.00
558.80
33.50
850
45.75
1162
15.50
393
17.00
431
22.00
558
6.00
152
8.50
215
11.50
292
20.00
508
6.20
157.48
9.62
244.34
8.84
224.53
80.0
36.2
116.0
52.6
6
150
6.625
168.3
16.00
406.40
22.00
558.80
33.50
850
45.75
1162
15.50
393
17.00
431
22.00
558
6.00
152
8.50
215
11.50
292
20.00
508
6.20
157.48
9.62
244.34
8.84
224.53
80.0
36.2
116.0
52.6
8
200
8.625
219.1
17.50
444.50
22.94
582.67
33.50
850
45.50
1155
16.75
425
20.00
508
25.25
641
7.00
177
8.75
222
12.75
323
18.50
469
6.05
153.67
9.40
238.76
10.21
259.33
122.0
55.3
158.0
71.6
NOTES:
The drawings shown above reflect the single-interlocked, pneumatic release trim with Series 776 Low-Pressure Actuator. In addition, these dimensions can
be applied to single-interlocked, pneumatic release; non-interlocked, pneumatic/electric release; single-interlocked, electric release; and double-interlocked,
electric (electric-pneumatic/electric) release trim.
The “A” dimension coupling is not shown for clarity.
Components shown as dotted lines denote optional equipment
* Measurements denoted with an asterisk take optional equipment into account
Optional drain connection kit is shown for reference and takeout dimensions.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
REV_H
30.82_5
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
DIMENSIONS FOR TRIM WITH SERIES 767
ELECTRIC/PNEUMATIC ACTUATORS
THE 4 INCH/114.3 MM CONFIGURATION IS SHOWN BELOW
1 ½ – 2 INCH/48.3 – 60.3 MM CONFIGURATIONS CONTAIN ¾ INCH/19 MM DRAIN VALVES.
2 ½ – 3 INCH/73.0 – 88.9 MM CONFIGURATIONS CONTAIN 1 ¼ INCH/31 MM DRAIN VALVES.
4 – 8 INCH/114.3 – 219.1 MM CONFIGURATIONS CONTAIN 2 INCH/50 MM DRAIN VALVES.
G
E
F
D
*D1
*B1
A
B
*A1
J
H
K
C
Full Open
Size
*E1
Aprx. Weight Ea.
lbs/kg
Dimensions – inches/mm
Nominal Size
Inches/
mm
Actual Outside
Diameter
Inches/
mm
A
A1*
B
B1*
C
D
D1*
E
E1*
F
G
H
J
K
Without
Trim
With
Trim
1½
40
1.900
48.3
9.00
228.60
16.43
417.32
28.00
711
42.75
1085
13.75
349
16.00
406
15.00
381
5.25
133
8.50
215
9.50
241
24.50
622
3.04
77.21
9.17
232.91
6.98
177.29
16.7
7.6
43.0
19.5
2
50
2.375
60.3
9.00
228.60
16.43
417.32
28.00
711
42.75
1085
13.75
349
16.00
406
15.00
381
5.25
133
8.50
215
9.50
241
24.50
622
3.04
77.21
9.17
232.91
6.98
177.29
17.0
7.7
43.0
19.5
2½
65
2.875
73.0
12.61
320.29
16.50
419.10
31.25
793
45.75
1162
13.50
342
16.25
412
18.00
457
5.25
133
9.00
228
9.75
247
22.75
577
3.90
99.06
10.50
266.70
6.93
176.02
41.0
18.7
65.0
29.5
76.1 mm
3.000
76.1
12.61
320.29
16.50
419.10
31.25
793
45.75
162
13.50
342
16.25
412
18.00
457
5.25
133
9.00
228
9.75
247
22.75
577
3.90
99.06
10.50
266.70
6.93
176.02
41.0
18.7
65.0
29.5
3
80
3.500
88.9
12.61
320.29
16.50
419.10
31.25
793
45.75
1162
13.50
342
16.25
412
18.00
457
5.25
133
9.00
228
9.75
247
22.75
577
3.90
99.06
10.50
266.70
6.93
176.02
41.0
18.7
65.0
29.5
4
100
4.500
114.3
15.03
381.76
19.78
502.41
32.75
831
47.50
1206
15.00
381
16.25
412
20.75
527
5.50
139
9.00
228
11.25
285
22.75
577
6.25
158.75
9.62
244.34
8.46
214.88
59.0
26.7
100.0
43.3
165.1 mm
6.500
165.1
16.00
406.40
22.00
558.80
32.75
831
47.50
1206
15.50
393
17.25
438
22.25
565
6.00
152
8.50
215
11.50
292
21.75
552
6.20
157.48
9.62
244.34
8.84
224.53
80.0
36.2
121.0
54.8
6
150
6.625
168.3
16.00
406.40
22.00
558.80
32.75
831
47.50
1206
15.50
393
17.25
438
22.25
565
6.00
152
8.50
215
11.50
292
21.75
552
6.20
157.48
9.62
244.34
8.84
224.53
80.0
36.2
121.0
54.8
8
200
8.625
219.1
17.50
444.50
22.94
582.67
32.50
825
47.00
1193
16.75
425
20.00
508
25.50
647
7.00
177
8.75
222
13.00
330
20.25
514
6.05
153.67
9.40
238.76
10.21
259.33
122.0
55.3
163.0
73.9
The “A” dimension coupling is not shown for clarity.
Components shown as dotted lines denote optional equipment
* Measurements denoted with an asterisk take optional equipment into account
Optional drain connection kit is shown for reference and takeout dimensions.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
30.82_6
REV_H
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
DIMENSIONS FOR TRIM WITH SERIES 798
DOUBLE-PNEUMATIC ACTUATORS
THE 4 INCH/114.3 MM CONFIGURATION IS SHOWN BELOW
1 ½ – 2 INCH/48.3 – 60.3 MM CONFIGURATIONS CONTAIN ¾ INCH/19 MM DRAIN VALVES.
2 ½ – 3 INCH/73.0 – 88.9 MM CONFIGURATIONS CONTAIN 1 ¼ INCH/31 MM DRAIN VALVES.
4 – 8 INCH/114.3 – 219.1 MM CONFIGURATIONS CONTAIN 2 INCH/50 MM DRAIN VALVES.
G
E
F
*F1
D
*B1
*D1
B
A
*A1
J
H
K
C
Size
*E1
Aprx. Weight Ea.
lbs/kg
Dimensions – inches/mm
Nominal Size
Inches/
mm
Actual Outside
Diameter
Inches/
mm
A
A1*
B
B1*
C
D
D1*
E
E1*
F
F1*
G
H
J
K
Without
Trim
With
Trim
1½
40
1.900
48.3
9.00
228.60
16.43
417.32
36.00
914
42.50
1079
15.75
400
19.00
482
21.00
533
5.25
133
8.50
215
10.75
273
12.75
323
24.25
615
3.04
77.21
9.17
232.91
6.98
177.29
16.7
7.6
43.0
19.5
2
50
2.375
60.3
9.00
228.60
16.43
417.32
36.00
914
42.50
1079
15.75
400
19.00
482
21.00
533
5.25
133
8.50
215
10.75
273
12.75
323
24.25
615
3.04
77.21
9.17
232.91
6.98
177.29
17.0
7.7
43.0
19.5
2½
65
2.875
73.0
12.61
320.29
16.50
419.10
39.25
996
45.75
1162
15.75
400
19.00
482
21.00
533
5.25
133
9.00
228
10.75
273
12.75
323
22.50
571
3.90
99.06
10.50
266.70
6.93
176.02
41.0
18.7
65.0
29.5
76.1 mm
3.000
76.1
12.61
320.29
16.50
419.10
39.25
996
45.75
1162
15.75
400
19.00
482
21.00
533
5.25
133
9.00
228
10.75
273
12.75
323
22.50
571
3.90
99.06
10.50
266.70
6.93
176.02
41.0
18.7
65.0
29.5
3
80
3.500
88.9
12.61
320.29
16.50
419.10
39.25
996
45.75
1162
15.75
400
19.00
482
21.00
533
5.25
133
9.00
228
10.75
273
12.75
323
22.50
571
3.90
99.06
10.50
266.70
6.93
176.02
41.0
18.7
65.0
29.5
4
100
4.500
114.3
15.03
381.76
19.78
502.41
40.50
1028
47.00
1193
16.75
425
19.00
482
24.00
609
5.50
139
9.00
228
12.25
311
14.25
361
22.25
565
6.25
158.75
9.62
244.34
8.46
214.88
59.0
26.7
111.0
50.3
165.1 mm
6.500
165.1
16.00
406.40
22.00
558.80
40.75
1035
47.25
1200
17.00
431
19.00
482
25.25
641
6.00
152
8.50
215
12.75
323
14.75
374
21.50
546
6.20
157.48
9.62
244.34
8.84
224.53
80.0
36.2
132.0
59.8
6
150
6.625
168.3
16.00
406.40
22.00
558.80
40.75
1035
47.25
1200
17.00
431
19.00
482
25.25
641
6.00
152
8.50
215
12.75
323
14.75
374
21.50
546
6.20
157.48
9.62
244.34
8.84
224.53
80.0
36.2
132.0
59.8
8
200
8.625
219.1
17.50
444.50
22.94
582.67
40.50
1028
47.00
1193
18.25
463
21.50
546
28.75
730
7.00
177
8.75
222
14.25
361
16.25
412
20.00
508
6.05
153.67
9.40
238.76
10.21
259.33
122.0
55.3
174.0
78.9
The “A” dimension coupling is not shown for clarity.
Components shown as dotted lines denote optional equipment
* Measurements denoted with an asterisk take optional equipment into account
Optional drain connection kit is shown for reference and takeout dimensions.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
REV_H
30.82_7
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
PERFORMANCE
Hydraulic Friction Loss
The chart below expresses the flow of water
at 65ºF/18ºC through a full open valve.
16
5.1
m
0mm
and
6"/
15
0m
m
m
0m
4"/
10
8"/20
6.1
d7
an
mm
m
3"/
80
5m
"/6
2½
1.0
0.9
0.8
0.7
0.6
0.5
0.4
mm
2"/
50
mm
"/4
0m
m
2.0
1½
PRESSURE DROP – PSI
3.0
m
6.0
5.0
4.0
0.3
0.2
0.1
10
20
30 40
60 80 100
200
300 400 600
1,000
800
2,000
4,000 6,000 10,000
3,000
8,000
20,000
FLOW RATE – GPM
Frictional Resistance
The chart below expresses the frictional resistance of Victaulic Series 769 FireLock NXT
Preaction Valve in equivalent feet of straight pipe.
Equivalent Length
of Pipe
Size
Nominal
Size
Inches/
mm
Actual
Outside Dia.
Inches/
mm
Feet
meters
1 1/2
40
1.900
48.3
3.00
0.914
2
50
2.375
60.3
9.00
2.743
2 1/2
65
2.875
73.0
8.00
2.438
76.1 mm
3.000
76.1
8.00
2.439
3
80
3.500
88.9
17.00
5.182
4
100
4.500
114.3
21.00
6.401
165.1 mm
6.500
165.1
22.00
6.706
6
150
6.625
168.3
22.00
6.706
8
200
8.625
219.1
50.00
15.240
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
30.82_8
REV_H
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
Cv VALUES
Cv values for flow of water at +60°F/+16°C through a fully open valve are shown in the
table below.
Formulas for Cv values:
Where:
Q = Flow (GPM)
∆P = Pressure Drop (psi)
Cv = Flow Coefficient
∆P = Q2
Cv2
Q = Cv x
∆P
Size
OPERATION
Nominal
Size
Inches/
mm
Actual
Outside Dia.
Inches/
mm
Cv/Kv
(Fully Open Valve)
1 1/2
40
1.900
48.3
60
52.0
2
50
2.375
60.3
110
95.0
2 1/2
65
2.875
73.0
180
156.0
76.1 mm
3.000
76.1
180
156.0
3
80
3.500
88.9
200
173.0
4
100
4.500
114.3
350
302.8
165.1 mm
6.500
165.1
1000
865.0
6
150
6.625
168.3
1000
865.0
8
200
8.625
219.1
1500
1499.1
The Victaulic Preaction System utilizes the Series 769 Preaction Valve to control the entry of the
water supply into the Preaction System piping and sprinklers. The Series 769 Preaction Valve is constructed with a clapper having a replaceable rubber face. The clapper makes contact with the valve
seat ring which has access holes to the intermediate chamber of the valve. The clapper is contacted
by the latch which is contacted by the diaphragm. In the set position, water supply pressure from
upstream of the water supply control valve is maintained in the diaphragm chamber which holds the
clapper in the closed/set position. The water is maintained in the diaphragm by one of the system
release mechanisms (pneumatic, hydraulic or electric). Upon the detection of an appropriate actuating event of the Preaction System (see system description above) the water supply pressure in the
diaphragm chamber is released. This release allows the latch to move to its open position, permitting
the clapper to pivot freely, thus allowing water into the system. Water will flow from all open sprinklers
in the piping. Also, water enters the intermediate chamber of the valve through the holes in the seat
ring. The water flows from the intermediate chamber to the alarm line thus activating the system
alarms. These alarms will continue to sound until the flow of water is stopped. When the flow of water
is stopped the spring assisted valve clapper returns to the closed position and the valve acts as an
alarm check valve until the system is put back into service as a Preaction System.
Manual Operation
Any time the manual release handle is pulled water will be released from the diaphragm chamber
and the valve will actuate, allowing water into the Preaction System. Water motor alarms and alarm
pressure switches will activate.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
REV_H
30.82_9
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
MATERIAL SPECIFICATIONS
Body: Ductile iron conforming to ASTM A-536, grade 65-45-12.
Clapper: Aluminum bronze UNS-C95500
Latch: Aluminum bronze UNS-C95500
Clapper Seal: Peroxide cured EPDM, ASTM D2000
Bushing and Seat O-rings: Nitrile
Springs: Stainless steel (300 Series)
Shafts: Stainless 17-4
Diaphragm: Peroxide cured EPDM with fabric reinforcement
Bill
1
2
3
4
5
6
7
8
9
10
11
of Materials
Valve Body
Clapper
Clapper Seal
Seal Ring
Seal Washer
Seal Retaining Ring
Seal Assembly Bolt
Bolt Seal
Clapper Spring
Clapper Shaft
Clapper Shaft Bushing and O-Ring (Qty. 2)
12
13
14
15
16
17
18
19
20
21
Cover Plate
Cover Plate Gasket
Cover Plate Bolts*
Latch
Latch Spring
Latch Shaft Bushing and O-Ring (Qty. 2)
Diaphragm
Diaphragm Cover
Diaphragm Cover Cap Screws (Qty. 8)
Latch Shaft
20
19
18
17
11
15
21
17
1
16
10
2
3
9
12
4
13
5
8
14
Exaggerated for clarity
11
6
7
* NOTE: The 1½-inch/48.3-mm and 2-inch/60.3-mm valve sizes contain washers under the heads of
the cover plate bolts.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
30.82_10
REV_H
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
TRIM PACKAGES
Trim Packages Options:
1 Non-Interlocked, Penumatic
2 Non-Interlocked, Pneumatic/Electric
3 Single-Interlocked, Pneumatic
4 Single-Interlocked, Electric or Double-Interlocked, Electric (Electric-Pneumatic/Electric)
5 Double-Interlocked, Electric/Pneumatic
6 Double-Interlocked, Pneumatic/Pneumatic
Trim packages include all required galvanized pipe and fittings. For trim package details and optional
accessories, see pages 17-22
Actuators:
• Series 776 Low-Pressure Actuator – The Series 776 Low-Pressure Actuator is pneumatically actuated and requires only 13 psi/90 kPa minimum air pressure, regardless of the system
supply pressure. This actuator allows the system to operate with a low air or gas pressure of
7 psi/48 kPa. Request submittal 30.65.
• Series 767 Electric/Pneumatic Actuator – The Series 767 Electric/Pneumatic Actuator
­provides a single trip point for the pneumatic event and an integral electric actuator. This
­actuator requires only 13 psi/90 kPa minimum air pressure, regardless of the system supply
pressure. This actuator allows the system to operate with a low air or gas pressure of 7 psi/
48 kPa. Request submittal 30.62.
• Series 798 Double-Pneumatic Actuator – The Series 798 Double-Pneumatic Actuator requires
two separate pneumatic activations in order to actuate the system. This actuator requires only
13 psi/90 kPa minimum air pressure, regardless of the system supply pressure. This actuator
allows the system to operate with a low air or gas pressure of 7 psi/48 kPa. Request submittal
30.61.
• Series 753-E Solenoid Valve – The Series 753-E Solenoid Valve is designed for use with
­systems that require electrical activation. Request submittal 30.63.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
REV_H
30.82_11
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
TRIM PACKAGES
Optional accessories:
• Series 746-LPA Dry Accelerator – The Series 746-LPA Dry Accelerator can be used on
­pneumatic release systems to improve response time. Request submittal 30.64.
• Series 760 Water Motor Alarm – The Series 760 Water Motor Alarm is a mechanical device
that sounds when a sustained flow of water occurs (such as with an open sprinkler). Request
submittal 30.32.
• Series 75B Supplemental Alarm Device – The Series 75B Supplemental Alarm Device is
designed to provide a continuous alarm for systems equipped with a mechanical device.
Request submittal 30.33.
• Series 75D Water Column Kit – The Series 75D Water Column Kit is designed to minimize
residual water in the riser from collecting above the clapper. Request submittal 30.34.
• Alarm Pressure Switch – Alarm Pressure Switches are designed to activate electrical alarms
and control panels when a sustained flow of water occurs (such as with an open sprinkler).
• Air Supervisory Pressure Switch – Air Pressure Supervisory Switches are used to monitor
­system air pressure and are available as low-pressure and high-pressure sensitivity.
• Air Supply System – The air supply system contains all components for establishing and
maintaining air in a pneumatic system. The compressor, low pressure alarms, ball valves, and
required trim are included in the air supply system.
• Air Compressor (See page 14 for more on the Victaulic Series 7C7 Compressor Package)
• Air Maintenance Trim Assembly
• Alarm Panels
• Drain Connection Kit
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
30.82_12
REV_H
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
AIR SUPPLY REQUIREMENTS
The required air pressure for Series 769 FireLock NXT Preaction Valves is 13 psi/90 kPa minimum,
regardless of the system supply pressure. Air pressures should be kept below 18 psi/124 kPa, unless
a Series 746-LPA Dry Accelerator is installed. Systems with air pressures higher than 18 psi/124 kPa
may require the addition of a Series 746-LPA Dry Accelerator.
If multiple Series 769 FireLock NXT Preaction Valves are installed with a common air supply, isolate
the systems with a spring-loaded, soft-seated ball check valve to ensure air integrity for each system.
Good practice is to include a ball valve for isolation and service of each individual system.
Set the air pressure to the required system air pressure. Air pressure differing from the required system air pressure could reduce system operation response time.
The engineer/system designer is responsible for sizing the compressor so that the entire system is
charged to the required air pressure within 30 minutes. DO NOT oversize the compressor to provide
more airflow. An oversized compressor will slow down or possibly prevent valve operation.
If the compressor fills the system too fast, it may be necessary to restrict the air supply. Restricting
the air supply will ensure that air being exhausted from an open sprinkler or manual release valve is
not replaced by the air supply system as fast as it is being exhausted.
COMPRESSOR SIZING
COMPRESSOR REQUIREMENTS
12
20 psi/138 kPa
13 psi/90 kPa
REQUIRED FLOW RATE (CFM)
10
8
6
4
2
0
1800
1550
1300
1050
800
550
300
50
SYSTEM CAPACITY (in gallons)
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
REV_H
30.82_13
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
BASE OR RISER-MOUNTED
COMPRESSORS
For base or riser-mounted compressors, the recommended air pressure of 13 psi/90 kPa is the
“on” or “low” pressure setting for the compressor. The “off” or “high” pressure setting should
be 18 psi/124 kPa. Victaulic offers the Series 7C7 Compressor package for FireLock NXT devices
which is riser-mounted and pre-set for the FireLock NXT pressure requirements as stated above.
For information on the Series 7C7 package, consult publication 30.22. The Series 7C7 Compressor
package is only available in North America.
When a base or riser-mounted air compressor supplies air to a Series 768 FireLock NXT Dry Valve,
it is not necessary to install the Victaulic Series 757 Regulated Air Maintenance Trim Assembly
(AMTA). In this case, the airline of the compressor connects to the trim at the fitting where the Series
757 Regulated AMTA is normally installed (refer to the applicable trim drawing). If the compressor is not equipped with a pressure switch, the Series 757P Air Maintenance Trim Assembly with
Pressure Switch should be installed. For information on the Series 757 Regulated Air Maintenance
Trim Assembly, see publication 30.35. For information on the Series 757P Air Maintenance Trim
Assembly, see publication 30.36.
SHOP AIR OR TANK-MOUNTED
AIR COMPRESSORS
In the event a compressor becomes inoperative, a properly sized tank-mounted air compressor
p­rovides the the greatest protection for systems.
When shop air or a tank-mounted air compressor is used, the Series 757 Regulated AMTA must be
installed. The Series 757 Regulated AMTA provides proper air regulation from the air reservoir to the
sprinkler system.
For tank-mounted air compressors, the recommended air pressure of 13 psi/90 kPa should be used
as the set point for the air regulator. The “on” pressure of the compressor should be at least 5 psi/
34 kPa above the set point of the air regulator.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
30.82_14
REV_H
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
SERIES 757 REGULATED AIR
MAINTENANCE TRIM ASSEMBLY
NOTICE
• Victaulic recommends a maximum of two Series 769 FireLock NXT Preaction Valves
per Series 757 Regulated AMTA
Bill of Materials
1 1⁄8"/3.2 mm Restrictor
2 Slow Fill Ball Valve (Normally Open)
3 Air Regulator
4 Strainer (100 Mesh)
5 Spring-Loaded, Soft-Seated
Ball Check Valve
6 Fast Fill Ball Valve (Normally Closed)
1
6
2
3
4
5
Exaggerated for clarity
SERIES 757P AIR MAINTENANCE TRIM
ASSEMBLY WITH PRESSURE SWITCH
NOTICE
• Victaulic recommends a maximum of two Series 769 FireLock NXT Preacttion Valves
per Series 757P AMTA with Pressure Switch.
6
Bill of Materials
8
Item Qty. Description
1
1 Restrictor (½-inch NPT)
2
1 Strainer (½-inch NPT)
7
3
1 Swing Check (½-inch NPT)
4
1 Slow-Fill Ball Valve
(Normally Open)
5
1 Spring-Loaded, Soft-Seated
Check Valve
6
1 Pressure Switch
7
2 Compression Fitting, Straight
(¼-inch NPT x ¼-inch Tube)
8
1 Copper Tubing (¼-inch OD)
13
9
11 Close Nipple
(½-inch NPT x 1.13)
10
1 Nipple (½-inch NPT x 4.00)
11
1 90° Female Elbow (½-inch NPT)
12
4 Female Tee (½-inch NPT)
13
3 Union (½-inch NPT)
14
2 Reducing Bushing
(½-inch NPT x ¼-inch NPT)
15
1 Fast-Fill Ball Valve
(Normally Closed)
2
16
1 Pressure Switch Isolation Ball
Valve (Normally Open Lockable)
14
16
1
9
12
4
5
11
3
10
FROM
COMPRESSOR
15
Exaggerated for clarity
TO
SYSTEM
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
REV_H
30.82_15
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
COMPRESSOR REQUIREMENTS
Compressor Requirements and Settings for Series 769 FireLock NXT Preaction Valves Installed
with Series 746-LPA Dry Accelerators
Set the air regulator of the Series 757 Regulated AMTA to 13 psi/90 kPa.
THE SERIES 757P AIR MAINTENANCE TRIM ASSEMBLY WITH PRESSURE SWITCH MUST NOT
BE USED ON A SERIES 769 FIRELOCK NXT PREACTION VALVE INSTALLED WITH A SERIES
746-LPA DRY ACCELERATOR.
When a Series 769 FireLock NXT Preaction Valve is installed with a Series 746-LPA Dry Accelerator,
the Series 757 Regulated AMTA must be used. NOTE: The use of an air regulator with a base or
riser-mounted compressor could cause short cycling, resulting in premature wear of the compressor.
In the event a compressor becomes inoperative, a properly sized tank-mounted air compressor
­provides the greatest protection for systems installed with a Series 746-LPA Dry Accelerator. In
this situation, air can be supplied continuously to the sprinkler system for an extended time period.
NOTE: The Series 757 Regulated AMTA must be used with a tank-mounted air compressor that
supplies air to a Series 769 FireLock NXT Preaction Valve installed with a Series 746-LPA Dry
Accelerator.
The air regulator of the Series 757 Regulated AMTA is a relief-type design. Any pressure in the
­system that is above the set point of the air regulator will be released. Therefore, charging the air regulator above the set point could cause premature operation of a valve installed with a Series 746‑LPA
Dry Accelerator. NOTE: The Series 746-LPA should not be used above 30 psi/207kPa. If higher pressures are required, the Series 746 should be used.
Settings for Air Supervisory Pressure Switches and Alarm Pressure Switches
Air supervisory pressure switches are required for preaction systems and must be set according to
the following instructions. NOTE: Switches for Vic-Quick Risers are pre-set at the factory.
Wire the air supervisory pressure switches to activate a low-pressure alarm signal. NOTE: In addition,
the local authority having jurisdiction may require a high-pressure alarm. Contact the local authority
having jurisdiction for this requirement.
Set the air supervisory pressure switches to activate at 2 – 4 psi/14 – 28 kPa below the minimum air
pressure required, but not lower than 10 psi/69 kPa.
Wire the alarm pressure switch to activate a water flow alarm.
Set the alarm pressure switch to activate on a pressure rise of 4 – 8 psi/28 – 55 kPa.
Remote System Test Valve Requirements
The remote system test valve (inspector’s test connection) should contain a UL Listed and/or FM
Approved valve (normally closed), which can be opened to simulate the operation of a sprinkler.
The remote system test valve (inspector’s test connection) should be located at the most hydraulically demanding location in the release system. NOTE: Multiple restrictions on the remote system
test valve (inspector’s test connection) may slow the air decay rate and cause the system to respond
slower than required.
The remote system test valve (inspector’s test connection) should terminate with an orifice equal to
the smallest orifice in the releasing system.
The remote system test valve (inspector’s test connection) is used to ensure that water reaches the
most remote part of the system within 60 seconds.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
30.82_16
REV_H
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
NON-INTERLOCKED,
PNEUMATIC RELEASE TRIM
Series 769 FireLock NXT Preaction Valve –
Non-Interlocked, Pneumatic Release Trim
(Optional Accessories Also Shown)
Bill of Materials
1 Series 769 FireLock NXT Preaction Valve
2 FireLock Rigid Coupling (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
3 Water Supply Main Control Valve (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
4 Drain Swing Check Valve
5 Drip Cup with Cap
6 Alarm Pressure Switch (Optional/Sold
16
Separately – Comes Standard when VQR
Assembly is Ordered)
7 Series 729 Drip Check Valve
8 Diaphragm-Charge-Line Ball Valve
(Normally Open)
17
9 3-in-1 Strainer/Check/Restrictor Assembly
10 Series 760 Water Motor Alarm
(Optional/Sold Separately)
21
11 Alarm Test Ball Valve
12 Diaphragm-Charge-Line Pressure
Gauge (0-300 psi/0-2068 kPa/0-20.7 Bar)
13 Series 749 Auto Drain
14 Series 776 Low-Pressure Actuator
15 Air Manifold
16 Air Supervisory Pressure Switch (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
17 System Pressure Gauge
(0-80 psi/0-552 kPa/0-5.5 Bar with Retard)
18 Water Supply Main Drain Valve - Flow Test
19 Water Supply Pressure Gauge
(0-300 psi/0-2068 kPa/0-20.7 Bar)
20 Drain Connection Kit (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
21 Gauge Valve
22 System Main Drain Valve
23 Series 755 Manual Pull Station
24 Series 748 Ball Check Valve
From System
Air Feed
15
To Pilot
Line
20
Location
A
14
24
5
22
To Drip
Cup
Location
4
A
Note 1
13 To Drip
Cup
Location
A
12
23
To System
18
19
9
21
21
11
10
1
7
To Drip
Cup
Location
2
6
A
8
3
From Water
Supply
Exaggerated for clarity
NOTE 1: Connection point for the Series 75D Water Column Device Kit.
For installation of the Series 75B Supplemental Alarm Device, refer to the instructions supplied with
the product.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
REV_H
30.82_17
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
NON-INTERLOCKED, PNEUMATIC/
ELECTRIC RELEASE TRIM
Series 769 FireLock NXT Preaction Valve –
Non-Interlocked, Pneumatic/Electric Release
Trim (Optional Accessories Also Shown)
Bill of Materials
1 Series 769 FireLock NXT Preaction Valve
2 FireLock Rigid Coupling (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
3 Water Supply Main Control Valve (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
4 Drain Swing Check Valve
5 Drip Cup with Cap
6 Alarm Pressure Switch (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
7 Series 729 Drip Check Valve
8 Diaphragm-Charge-Line Ball Valve
(Normally Open)
9 3-in-1 Strainer/Check/Restrictor
17
Assembly
10 Series 760 Water Motor Alarm
(Optional/Sold Separately)
21
11 Alarm Test Ball Valve
12 Diaphragm-Charge-Line Pressure
Gauge (0-300 psi/0-2068 kPa/0-20.7 Bar)
13 Series 749 Auto Drain
14 Series 776 Low-Pressure Actuator
19
15 Air Manifold
16 Air Supervisory Pressure Switch (Optional/Sold
21
Separately – Comes Standard when VQR
Assembly is Ordered)
17 System Pressure Gauge
(0-80 psi/0-552 kPa/0-5.5 Bar with Retard)
18 Water Supply Main Drain Valve - Flow Test
19 Water Supply Pressure Gauge
(0-300 psi/0-2068 kPa/0-20.7 Bar)
20 Drain Connection Kit (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
21 Gauge Valve
22 System Main Drain Valve
23 Series 755 Manual Pull Station
24 Series 748 Ball Check Valve
25 Series 753-E Solenoid Valve
26 Series 746-LPA Dry Accelerator
(Optional/Sold Separately)
26a
26
From System
Air Feed
26b
15
Location
A
20
16
14
24
5
22
4
To Drip Cup
Location
A
18
Note 1
13
To Drip
Cup
Location
A
12
25
To System
9
21
23
To Drip Cup
Location
11
A
10
1
6
7
To Drip Cup
Location
2
A
8
3
From Water
Supply
Exaggerated for clarity
NOTE 1: Connection point for the Series 75D Water Column Device Kit.
For installation of the Series 75B Supplemental Alarm Device, refer to the instructions supplied with
the product.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
30.82_18
REV_H
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
SINGLE-INTERLOCKED,
PNEUMATIC RELEASE TRIM
Series 769 FireLock NXT Preaction Valve –
Single-Interlocked, Pneumatic Release Trim
(Optional Accessories Also Shown)
Bill of Materials
1 Series 769 FireLock NXT Preaction Valve
2 FireLock Rigid Coupling (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
3 Water Supply Main Control Valve (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
4 Drain Swing Check Valve
5 Drip Cup with Cap
6 Alarm Pressure Switch (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
7 Series 729 Drip Check Valve
16
8 Diaphragm-Charge-Line Ball Valve
(Normally Open)
9 3-in-1 Strainer/Check/Restrictor Assembly
10 Series 760 Water Motor Alarm
(Optional/Sold Separately)
11 Alarm Test Ball Valve
22
17
12 Diaphragm-Charge-Line Pressure
Gauge (0-300 psi/0-2068 kPa/0-20.7 Bar)
13 Series 749 Auto Drain
21
14 Series 776 Low-Pressure Actuator
15 Air Manifold
16 Air Supervisory Pressure Switch (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
17 System Pressure Gauge
19
(0-80 psi/0-552 kPa/0-5.5 Bar with Retard)
18 Water Supply Main Drain Valve - Flow Test
21
19 Water Supply Pressure Gauge
(0-300 psi/0-2068 kPa/0-20.7 Bar)
20 Drain Connection Kit (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
21 Gauge Valve
22 System Main Drain Valve
23 Series 755 Manual Pull Station
24 Series 748 Ball Check Valve
25 Series 746-LPA Dry Accelerator
(Optional/Sold Separately)
25a
25
25b
To Pilot
Line
15
From System
Air Feed
20
Location
A
14
24
5
To Drip
Cup
Location
4
A
13
To Drip
Cup
Location
A
12
23
To System
Note 1
18
9
21
11
10
1
7
To Drip Cup
Location
2
A
6
8
3
From Water
Supply
Exaggerated for clarity
NOTE 1: Connection point for the Series 75D Water Column Device Kit.
For installation of the Series 75B Supplemental Alarm Device, refer to the instructions supplied with
the product.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
REV_H
30.82_19
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
SINGLE-INTERLOCKED,
OR DOUBLE-INTERLOCKED,
ELECTRIC RELEASE TRIM
Series 769 FireLock NXT Preaction
Valve – Single-Interlocked, Electric Release
Trim or Double-Interlocked, Electric
Release (Electric-Pneumatic/Electric) Trim
(Optional Accessories Also Shown)
Bill of Materials
1 Series 769 FireLock NXT Preaction Valve
2 FireLock Rigid Coupling (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
3 Water Supply Main Control Valve (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
4 Drain Swing Check Valve
5 Drip Cup with Cap
6 Alarm Pressure Switch (Optional/Sold
Separately – Comes Standard when VQR 16
Assembly is Ordered)
7 Series 729 Drip Check Valve
20
8 Diaphragm-Charge-Line Ball Valve
(Normally Open)
9 3-in-1 Strainer/Check/Restrictor Assembly
10 Series 760 Water Motor Alarm
(Optional/Sold Separately)
11 Alarm Test Ball Valve
18
12 Diaphragm-Charge-Line Pressure
Gauge (0-300 psi/0-2068 kPa/0-20.7 Bar)
20
13 Series 749 Auto Drain
14 Series 753-E Solenoid Valve
15 Air Supervisory Pressure Switch**
16 System Pressure Gauge
(0-80 psi/0-552 kPa/0-5.5 Bar with Retard)
17 Water Supply Main Drain Valve - Flow Test
18 Water Supply Pressure Gauge
(0-300 psi/0-2068 kPa/0-20.7 Bar)
19 Drain Connection Kit (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
20 Gauge Valve
21 System Main Drain Valve
22 Series 755 Manual Pull Station
23 Series 748 Ball Check Valve
**Item #15 is optional/sold separately (or standard when VQR
assembly is ordered) for single-interlocked, electric release trim.
**Item #15 is standard for double-interlocked, electric release
(electric-pneumatic/electric) trim.
From System
Air Feed
15
Location
19
A
14
23
5
21
To Drip
Cup
Location
4
13
To Drip
Cup
Location
A
A
Note 1
12
22
To System
17
20
9
11
10
1
7
6
To Drip Cup
Location
2
A
8
3
From Water
Supply
Exaggerated for clarity
NOTE 1: Connection point for the Series 75D Water Column Device Kit.
For installation of the Series 75B Supplemental Alarm Device, refer to the instructions supplied with
the product.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
30.82_20
REV_H
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
DOUBLE-INTERLOCKED,
ELECTRIC/PNEUMATIC RELEASE TRIM
Series 769 FireLock NXT Preaction Valve  –
Double-Interlocked, Electric/Pneumatic
Release Trim
(Optional Accessories Also Shown)
Bill of Materials
1 Series 769 FireLock NXT Preaction Valve
2 FireLock Rigid Coupling (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
3 Water Supply Main Control Valve
(Optional/Sold Separately – Comes
Standard when VQR Assembly is Ordered)
4 Drain Swing Check Valve
5 Drip Cup with Cap
6 Alarm Pressure Switch (Optional/Sold
Separately – Comes Standard when VQR
16
Assembly is Ordered)
7 Series 729 Drip Check Valve
8 Diaphragm-Charge-Line Ball Valve
(Normally Open)
9 3-in-1 Strainer/Check/Restrictor
Assembly
22
17
10 Series 760 Water Motor Alarm
(Optional/Sold Separately)
11 Alarm Test Ball Valve
21
12 Diaphragm-Charge-Line Pressure
Gauge (0-300 psi/0-2068 kPa/0-20.7 Bar)
13 Series 749 Auto Drain
14 Series 767 Electric/Pneumatic Actuator
15 Air Manifold
16 Air Supervisory Pressure Switch
19
(Optional/Sold Separately – Comes
Standard when VQR Assembly is Ordered)
21
17 System Pressure Gauge
(0-80 psi/0-552 kPa/0-5.5 Bar with Retard)
18 Water Supply Main Drain Valve - Flow Test
19 Water Supply Pressure Gauge
(0-300 psi/0-2068 kPa/0-20.7 Bar)
20 Drain Connection Kit (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
21 Gauge Valve
22 System Main Drain Valve
23 Series 755 Manual Pull Station
24 Series 748 Ball Check Valve
25 Series 746-LPA Dry Accelerator
(Optional/Sold Separately)
26 Upper Chamber Strainer (100 Mesh)
27 Upper Chamber Pressure Gauge for
Series 767 Electric/Pneumatic Actuator
28 Auto Vent for Series 767 Electric/
Pneumatic Actuator
29 Upper Chamber Inlet Restrictor
.032-inch) for Series 767 Electric/
Pneumatic Actuator
30 Upper Chamber Check Valve (¼-inch)
for Series 767 Electric/Pneumatic Actuator
25a
NOTE: When installing the optional Series 746-LPA Dry Accelerator,
relocate the auto vent to the location of the indicated plug.
25
From System
Air Feed
25b
15
28
20
27
Location
A
14
29
30
24
26
5
To Drip Cup
Location
4
13
To Drip
Cup
Location
B
B
12
23
Note 1
To System
18
21
9
11
10
1
7
To Drip
Cup
Location
2
B
6
8
3
From Water
Supply
Exaggerated for clarity
NOTE 1: Connection point for the Series 75D Water Column Device Kit.
For installation of the Series 75B Supplemental Alarm Device, refer to the instructions supplied with
the product.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
REV_H
30.82_21
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
DOUBLE-INTERLOCKED, PNEUMATIC/
PNEUMATIC RELEASE TRIM
Series 769 FireLock NXT Preaction Valve –
Double-Interlocked, Pneumatic/Pneumatic
Release Trim
(Optional Accessories Also Shown)
Bill of Materials
1 Series 769 FireLock NXT Preaction Valve
2 FireLock Rigid Coupling (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
3 Water Supply Main Control Valve (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
4 Drain Swing Check Valve
5 Drip Cup with Cap
6 Alarm Pressure Switch (Optional/Sold
From System
Separately – Comes Standard when
Air Feed
VQR Assembly is Ordered)
7 Series 729 Drip Check Valve
8 Diaphragm-Charge-Line Ball Valve
(Normally Open)
9 3-in-1 Strainer/Check/Restrictor Assembly
10 Series 760 Water Motor Alarm
(Optional/Sold Separately)
11 Alarm Test Ball Valve
12 Diaphragm-Charge-Line Pressure
Gauge (0-300 psi/0-2068 kPa/0-20.7 Bar)
13 Series 749 Auto Drain
14 Series 798 Pneumatic/Pneumatic Actuator
15 Air Manifold
16 Air Supervisory Pressure Switch (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
17 System Pressure Gauge
(0-80 psi/0-552 kPa/0-5.5 Bar with Retard)
18 Water Supply Main Drain Valve - Flow Test
19 Water Supply Pressure Gauge
(0-300 psi/0-2068 kPa/0-20.7 Bar)
20 Drain Connection Kit (Optional/Sold
Separately – Comes Standard when VQR
Assembly is Ordered)
21 Gauge Valve
22 System Main Drain Valve
23 Series 755 Manual Pull Station
24 Series 748 Ball Check Valve
25 Series 746-LPA Dry Accelerator
(Optional/Sold Separately)
26 Air Feed Valve Assembly
26a Pilot Line Fill Valve and Shutoff Valve
(Shutoff Valve has Yellow Handle)
26b System Line Fill Valve and Shutoff Valve
(Shutoff Valve has Yellow Handle)
27 System Air Line Strainer (100 Mesh)
28 Pilot Line Strainer (100 Mesh)
29 Pilot Line Pressure Gauge
(0-80 psi/0-552 kPa/0-5.5 Bar with Retard)
30 Auto Vent for Series 798 Pneumatic/
Pneumatic Actuators
29
21
25a
25
26
25
30
26a Pilot
Line
25b
NOTE: When installing the
optional Series 746-LPA Dry
Accelerator(s), relocate the
auto vent to the location of
the indicated plug.
To Pilot
Line
28
26
26b System
Line
16
15
27
15
Location
A
16
14
24
5
22
17
20
13 To Drip Cup
To Drip Cup
Location
4
21
Location
A
A
Note 1
12
To System
18
21
19
9
21
23
11
10
1
7
6
To Drip Cup
Location
2
A
8
3
From Water
Supply
Exaggerated for clarity
NOTE 1: Connection point for the Series 75D Water Column Device Kit.
For installation of the Series 75B Supplemental Alarm Device, refer to the instructions supplied with
the product.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
30.82_22
REV_H
30.82
FIRE PROTECTION PRODUCTS – DEVICES
FireLock NXT™ Actuated Valve with Preaction Trim
SERIES 769
With Preaction Trim
Grooved x Grooved
WARRANTY
Refer to the Warranty section of the current Price List or contact Victaulic for details.
NOTE
This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be
installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the
right to change product specifications, designs and standard equipment without notice and without
incurring obligations.
WARNING
WARNING
• This product must be installed by an experienced, trained installer,
in accordance with the instructions provided with each valve. These
­instructions contain important information.
Failure to follow these instructions may result in serious personal injury,
property damage, or valve leakage.
If you need additional copies of this product literature or the valve
­installation instructions, or if you have any questions about the safe
installation and use of this device, contact Victaulic Company, P.O.
Box 31, Easton, PA 18044-0031 USA, Telephone: 001-610-559-3300.
For complete contact information, visit www.victaulic.com
30.82
4220 REV H
UPDATED 11/2011
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2015 VICTAULIC COMPANY. ALL RIGHTS RESERVED.
30.82
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising