Instructions

Instructions
Instructions
116866 – Chrome
116861 – PVD brushed nickel
116869 – Brushed bronze
40-K82-CYCH-AD-Z – Chrome
40-K82-CYBN-AD-Z – PVD brushed nickel
40-K82-CYBB-AD-Z – Brushed bronze
Two Handle Kitchen Faucet
Certifications
CALIFORNIA LEAD
PLUMBING LAW
*Image may vary slightly from actual product
Tools Required
Maintenance
Adjustable Wrench
Groove Joint Pliers
Pipe Wrench
Phillips Screwdriver
Pipe Tape or pipe thread compound
Your new kitchen faucet is designed for years of trouble-free
performance.
Safety Tips
If you solder the joints during installation of the faucet, the seats,
cartridges, and washers must be removed before using a flame
or the warranty will be voided on these parts.
Protect your eyes with safety glasses when cutting or soldering
water supply lines.
Cover the sink drain to avoid losing parts.
Things You May Need
Installations may vary depending on how the previous faucet was
installed. Supplies necessary for the installation of your faucet are
not all included; however, they are available wherever plumbing
supplies are sold.
Keep it looking new by cleaning it periodically with a soft cloth.
Avoid abrasive cleaners, steel wool, and harsh chemicals as
these will dull the finish and void your warranty.
Important Points
Prior to beginning installation, turn off the hot and cold water
lines, then turn on the old faucet to release built-up pressure.
When installing your new faucet, turn the connector nuts finger
tight, then use one wrench to hold the fitting and a second
wrench to tighten the nut. Connections that are too tight will
reduce the integrity of the system.
Wrap all threaded connections with PTFE pipe tape available
at your local hardware or plumbing supply store. Always wrap
in a clock-wise direction.
Contact Us
For Customer Service please call 877-319-3757, or go to
homewerksww.com.
www.homewerksww.com
Effective/Rev Date: March 15, 2011
1
Instructions
116866 – Chrome
116861 – PVD brushed nickel
116869 – Brushed bronze
40-K82-CYCH-AD-Z – Chrome
40-K82-CYBN-AD-Z – PVD brushed nickel
40-K82-CYBB-AD-Z – Brushed bronze
Two Handle Kitchen Faucet
Certifications
CALIFORNIA LEAD
PLUMBING LAW
Preparation and Assembly
1
Locate water supply inlet and shut off water
supply valve. These are usually found under
the sink or near the water heater. Remove old
faucet. Clean and dry sink surface area where
new faucet will be mounted.
4
2
3
Insert sprayer support through far right hole on
the sink. Screw the nut onto the shank from
underneath the sink, hand tighten only.
5
For models with spray (fits 4-hole sinks)
Insert spray hose down through the support and
sink. Attach the spray hose to the connection
beneath the faucet by aligning the tabs on quick
connector. Push quick connector housing firmly
upward and snap onto receiving tube tab. Pull
down moderately to ensure connection has
been made.
6
2
1
3
Place new faucet in position on sink. From
under sink, thread mounting nuts onto
faucet. Tighten mounting nuts.
www.homewerksww.com
Make connections to water lines. Use 1/2" IPS
faucet connections (1) or use the supplied
coupling nuts (3) with 3/8" O.D. ball-nose risers
(2) (not supplied). Use wrenches to tighten
connections. Do not overtighten.
Important: After installation is completed,
remove aerator. Turn on water supply and
allow both hot and cold water to run for at
least one minute each. While water is running,
check for leaks. Replace aerator. Tighten nuts
slightly to stop minor leaks. If problems
persist, refer to troubleshooting chart.
Effective/Rev Date: March 15, 2011
2
Troubleshooting
116866 – Chrome
116861 – PVD brushed nickel
116869 – Brushed bronze
40-K82-CYCH-AD-Z – Chrome
40-K82-CYBN-AD-Z – PVD brushed nickel
40-K82-CYBB-AD-Z – Brushed bronze
Two Handle Kitchen Faucet
Certifications
CALIFORNIA LEAD
PLUMBING LAW
Troubleshooting
PROBLEM: Leaks underneath handle.
CAUSE: Bonnet has come loose or O-ring on cartridge is dirty or twisted.
ACTION:
1. Move the handle to the off position. Remove index button and
unscrew the handle screw and remover the handle (Diagram A).
2. Tighten the bonnet by turning it clockwise (Diagram B). Move the
cartridge stem to the on position. The leak should stop draining out
from around the cartridge stem.
3. If the leak does not stop, shut off the water supply. Remove the
bonnet by turning it counter-clockwise. Lift out the cartridge valve.
Inspect the larger O-ring on the cartridge bonnet. Replace the cartridge
by calling Customer Service.
4. Position the cartridge back into the faucet body (Diagram C). Make sure
the ridges on the two sides of the cartridge bonnet fit into the grooves
on the two sides of the faucet body. Tightly screw the bonnet onto the
faucet body.
5. Re-install the handle.
PROBLEM: Water does not completely shut off.
CAUSE: Rubber valve seat is dirty, stuck, or broken.
ACTION:
1. Shut off the cold water supply. If leak stops, the problem is on the cold
side. If leak continues, the problem is on the hot side. Shut off the hot
water supply to determine if both the cold and hot side have a problem.
2. Remove the handle on the problem side. Loosen the bonnet by turning
it counter-clockwise (Diagram D). Lift out the cartridge assembly.
3. Replace the cartridge in the faucet body. Make sure that the ridges on
the two sides of the cartridge bonnet fit into the grooves on the two
sides of the faucet body (Diagram E). Tightly screw the bonnet onto
the faucet body.
4. Re-install the handle.
PROBLEM: Faucet leaks around aerator.
CAUSE: Aerator incorrectly fitted.
ACTION:
1. U
nscrew the aerator by turning it clockwise (Diagram F). Inspect the
black rubber packing inside the aerator. The rubber packing should
be flat.
2. Screw the aerator onto the spout end and tighten.
PROBLEM: Improper water pattern.
CAUSE: Aerator dirty or small parts inside aerator improperly installed.
ACTION:
1. Remove the aerator from the spout end by turning it clockwise.
2. Gently flush the small parts inside the aerator to clear away any debris.
3. Re-install the small parts as shown in the exploded diagram (Diagram
G). Metal screens must be flat and plastic supporter must be straight.
4. Screw the aerator onto the spout end and tighten.
A
B
C
D
E
F
G
www.homewerksww.com
Effective/Rev Date: March 15, 2011
3
Specifications
Physical Characteristics
•
•
•
•
•
•
•
Description: Two handle, high-rise kitchen faucet with
8" centerset, brass waterways, ceramic cartridges and
matching side-spray
Max. Flow Rate: 2.2 GPM (8.3 LPM)
4-hole installation
ASME A112.18.1/CSA B125 Certified
Meets ANSI/NSF61-9 Low Lead Requirements
This product complies with 0.25% weighted average lead
content on wetted surfaces
Total Weight of Item: 1485.55g
No.
Part Description
Material
1
Spout
Brass C37700+Brass C27000
2
3
6
7
116866 – Chrome
116861 – PVD brushed nickel
116869 – Brushed bronze
40-K82-CYCH-AD-Z – Chrome
40-K82-CYBN-AD-Z – PVD brushed nickel
40-K82-CYBB-AD-Z – Brushed bronze
1
18b
POM M90+S.S.
O-ring
Ring
POM M90
Spout seat
ZZnA14
9
Diverter
POM+NBR+EPDM+Brass
10
Escutcheon
S.S.201
11
Body
Brass+Plastic+VT70+NBR+SUS
12
Base plate
Plastic PP20C
13
Mounting nut
ABS PA727
14
Handle
ZZnA14
15
Cap
ZZnA14
16
Bolt
Steel Q235A
17
Retainer
ZZnA14
18A
Hot index
Brass C37700
18B
Cold index
Brass C37700
19
Screw
S.S.302/S.S.304
20
Handle seat
ZZnA14
21
Inverter
POM M90
22
Bonnet
ZZnA14
23
Washer
POM M90
24A
Hot cartridge
24B
Cold cartridge
Brass C37700+POM M90+S.S. 302+
H65+Silica gel+Ceramic
25
Side spray
ABS+Brass
20
5
4
14
15
NBR N7008F
POM M90
19
2
3
Brass C37700
Retainer
8
www.homewerksww.com
CALIFORNIA LEAD
PLUMBING LAW
EPDM E7008F
Aerator assembly
4
5
Certifications
16
18a
19
17
16
7
20
21
22
23
9
24b
10
23
15
21
8
22
17
6
24a
11
25
12
13
13
Effective/Rev Date: March 15, 2011
4
14
Rough-In
116866 – Chrome
116861 – PVD brushed nickel
116869 – Brushed bronze
40-K82-CYCH-AD-Z – Chrome
40-K82-CYBN-AD-Z – PVD brushed nickel
40-K82-CYBB-AD-Z – Brushed bronze
Certifications
Two Handle Kitchen Faucet
CALIFORNIA LEAD
PLUMBING LAW
10 1/16"
14 9/16"
6 3/8"
1 3/4"
6 1/16"
11 7/16"
8 3/8"
1/2"-14NPSM-2A
8"
10 3/8"
www.homewerksww.com
2"
1 5/16"
2 7/16"
Effective/Rev Date: March 15, 2011
5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement