“A-PAK” ALARM SYSTEM INSTALLATION

“A-PAK” ALARM SYSTEM INSTALLATION
NOTICE TO INSTALLER: Instructions must remain with installation.
SECTION: 6.10.100
Your Peace of Mind is Our Top Priority ®
FM0483
0112
Supersedes
1111/2
®
Product information presented
here reflects conditions at time
of publication. Consult factory
regarding discrepancies or
inconsistencies.
MAIL TO: P.O. BOX 16347 • Louisville, KY 40256-0347
SHIP TO: 3649 Cane Run Road • Louisville, KY 40211-1961
(502) 778-2731 • 1 (800) 928-PUMP • FAX (502) 774-3624
visit our web site:
www.zoeller.com
“A-PAK” ALARM SYSTEM INSTALLATION INSTRUCTIONS
FOR YOUR PROTECTION ALWAYS DISCONNECT FROM POWER SOURCE BEFORE HANDLING. The “A-Pak” Alarm
system has a double insulated plastic enclosure for your protection and is supplied with a 2-prong plug.
specifications
This alarm system monitors liquid levels in lift pump chambers, sump pump basins, holding tanks, sewage, agricultural
and other non-potable water applications. It features a red warning light, green “power on” light, alarm test switch and
horn silence switch. “A-Pak” primary voltage is 120 VAC, 60 Hz, 2.4 watts max (alarm condition) (circuit is not supervised).
Secondary voltage is 9 VDC (circuit is not supervised). Battery backup power is 9 VDC. NOTE: 9V battery is not included
and must be purchased separately.
CABLE CLASP
WASHER
NOTE: The alarm panel plugs into a standard household 120 VAC socket. DO NOT plug “A-Pak” Alarm System into the
same circuit as the pump. The “A-Pak” Alarm System should be connected to a circuit separate from the pump circuit.
Push test button to check alarm panel for operation.
FACEPLATE SCREW
SK2148
ALARM PANEL INSTALLATION
1) Before installing alarm panel, remove battery cover on side of alarm panel and install a 9V battery. (not included)
2) Mount the alarm panel indoors with screws provided. NOTE: The mounting screw is to be located over a wall stud or
used with a wall anchor sized for a #8 x 1.25 self tapping screw.
3) Hang the panel by the keyhole in the back of the alarm enclosure and install the second screw between the tabs
located on bottom of the enclosure.
4) Using the provided cable clamp, secure the power cord to the outlet as shown (see Fig. A). Use existing receptacle
faceplate screw and supplied washer.
Figure A
CONTROL SWITCH INSTALLATION
MECHANICAL FLOAT SWITCH
(10-1494, 10-2614)
CLAMP DETAIL
(Tether Length Non-Adjustable)
1) Place cord into clamp and secure to discharge pipe as shown in clamp detail (see
Fig. B). NOTE: Do not install the cord under the hose clamp.
2) Tighten the hose clamp with a screwdriver. NOTE: Do not over tighten; over tightening may cause damage to the plastic clamp.
3) Make sure the float cable is not allowed to touch the excess hose clamp band during operation.
4) The float switch must be suspended seven inches below desired activation level. (see Fig. D)
5) Allow system to cycle to ensure proper operation.
3.5 INCH
TETHER LENGTH
FOR DOUBLE
FLOAT
3.5 INCH
MINIMUM
TETHER LENGTH
FOR PUMP
SWITCH
sk1301D
Figure B
LIFT PUMP
SEWAGE HOLDING TANK
Suspend control switch above pump turn on level. If a pump failure causes
high-level condition, the A-Pak Alarm System will activate (see Fig. C).
Suspend control switch into tank seven inches below desired
alarm level. A-Pak Alarm System will activate if float ascends to
alarm level (see Fig. D).
ALARM
TEST
ALARM
TO POWER SUPPLY
NOTE:
"DO NOT" PLUG "A-PAK ALARM SYSTEM
INTO THE SAME CIRCUIT AS THE PUMP
POWER ON
ZOELLER
UNICHECK
SILENCE
TO POWER SUPPLY
ZOELLER
FIBERGLASS
OR POLYETHYLENE
BASIN
ALARM
"ON" LEVEL
ZOELLER
VARIABLE LEVEL
CONTROL SWITCH
4" OF GRAVEL
PUMP "ON"
LEVEL
sk1301b
PUMP "OFF"
LEVEL
sk2376
Figure D
Figure C
© Copyright 2012 Zoeller Co. All rights reserved.
PN 1012302 Rev. F
MODEL TAAB
CONTROL SWITCH INSTALLATION
VERTICAL REED FLOAT SWITCH
(10-2613, 10-2615)
Do not install switch in direct line of incoming liquid.
1) Place the clamp into the switch housing as shown. (see Fig. E).
2) Locate clamp at desired activation level and secure the clamp to the discharge pipe as shown (see Fig. E).
NOTE: Do not install cord under hose clamp.
3) Tighten the hose clamp using a screwdriver. Over tightening may result in damage to the switch housing.
4) Check installation. Allow system to cycle to insure proper operation.
NOTE: When installing the control switch, a cable strain relief must be used to secure the control switch cord.
sk1301F
sk1301G
Figure E
Figure F
NOTE: Alarm systems 10-2613 and 10-2615 are not intended to be used in sewage holding tank systems.
CONTROL SWITCH WIRING
Connect the two conductors from the control switch to either of the terminations on the bottom of the alarm panel (see Fig. G).
The control switch operates on low voltage and is isolated from the 120 VAC power line to reduce shock hazards.
TEST
Check and test your installation by lifting the float manually (see Fig. D or F). The alarm panel should indicate an alarm
condition. The Zoeller Company cannot be responsible for damages caused by faulty or negligent installation of this device.
We respectfully suggest you engage the services of a qualified licensed electrician or service person. Push TEST button
once per week to verify proper operation.
LOUISVILLE, KY
UL
R
R
LISTED
288X
LR54245
WARNING:
ELECTRICAL SHOCK
HAZARD
FAILURE TO DISCONNECT ALL
POWER BEFORE SERVICING
COULD RESULT IN INJURY OR DEATH.
SK2375
Figure G
© Copyright 2012 Zoeller Co. All rights reserved.
MODELS 10-2614 AND 10-2615 “A-PAK” ALARM SYSTEMS WITH AUXILLIARY CONTACTS
WIRING INSTRUCTIONS
ELECTRICAL SHOCK HAZARD - Disconnect
all power sources before servicing. Failure to do so could result in
serious injury or death.
1) Remove the three screws from the back of the enclosure as shown in
Fig. H.
2) Remove the back of the enclosure. Note the position of the power cord
in the enclosure. The cord will need to be located in the same manner
when the enclosure back is replaced.
3) Determine the location where the auxiliary contact wires will enter the
housing. See Fig. I for recommended location. Before drilling the hole,
loosen the circuit board mounting screw and remove the circuit board.
See Fig. J.
4) At the selected location, drill a hole in the enclosure suitable for the
strain relief that will be used (strain relief not included).
5) Install strain relief and reinstall the circuit board. Connect wires to the
terminal block shown in Fig. J.
6) Markings on the circuit board show positions for Common (C), Normally
Open (NO), and Normally Closed (NC).
Figure H
7) Position the power cord into place as it was prior to removing the
enclosure back as shown in Fig. J.
8) Reinstall the enclosure back and three screws.
Do not over torque screws. Screw bosses may
become stripped.
9) Note that while testing the installed product, the auxiliary alarm wired to
the auxiliary contacts should activate in an alarm condition. The auxiliary
alarm should also remain in alarm condition when the silence button is
pushed.
Auxiliary Contacts Specifications
Voltage:
Current:
120 VAC
5 amps max. N/O
3 amps max. N/C
NOTE: This unit includes auxiliary contact option. Due to increased
power consumption, if an alarm condition occurs while on battery
backup power, this option will reduce the life of the battery.
Figure I
Figure J
sk2775
All electrical systems must be installed by a qualified licensed electrician according to the
National Electrical Code and all other applicable codes.
© Copyright 2012 Zoeller Co. All rights reserved.
BELL ALARM SYSTEMS
TYPICAL INSTALLATION AND WIRING INSTRUCTIONS
All electrical systems must be installed by a qualified licensed electrician according to the
National Electrical Code and all other applicable codes.
Model
Voltage
dB @ 10’
10-0015
115V
74
10-0016
230V
74
10-0028
115V
78
Bell
Transformer
o
o
o
Float
o
o
o
o
NOTE: Utility box and cordage sold separately. Bell Alarms 10-0015 and 10-0016 are designed to be used with Alarm Packs 10-2614 and 10-2615.
TYPICAL SIMPLEX SYSTEMS WITH BELL ALARM SYSTEM
BELL ALARM
ALARM
TRANSFORMER
DISCONNECTS
NOT SHOWN
ALARM PANEL
DISCONNECTS
NOT SHOWN
"DO NOT" PLUG "A-PAK ALARM SYSTEM
INTO THE SAME CIRCUIT AS THE PUMP
TEST
ALARM
POWER ON
SILENCE
AUX. CONTACTS
ZOELLER
UNICHECK
TRANSFORMER
TO POWER SUPPLY
TO POWER
SUPPLY
ZOELLER
UNICHECK
TO POWER
SUPPLY
ZOELLER
FIBERGLASS
OR POLYETHYLENE
BASIN
ZOELLER
FIBERGLASS
OR POLYETHYLENE
BASIN
ALARM
"ON" LEVEL
ALARM
"ON" LEVEL
ZOELLER
VARIABLE LEVEL
CONTROL SWITCH
ZOELLER
VARIABLE LEVEL
CONTROL SWITCH
4" OF GRAVEL
4" OF GRAVEL
PUMP "ON"
LEVEL
PUMP "ON"
LEVEL
PUMP "OFF"
LEVEL
PUMP "OFF"
LEVEL
sk2911
sk367
WIRING DIAGRAM
TRANSFORMER
115 TO 8V
OR
(10-0015)
(10-0016)
(10-0028)
DISCONNECT
NOT SHOWN
ALARM BELL
8V
230 TO 8V
L1
POWER
SUPPLY
L2
UTILITY
BOX
ZOELLER VARIABLE LEVEL
CONTROL SWITCH
SEE FM0419 FOR MOUNTING
TO
NOTE: ALARM SYSTEM
SHOULD BE ON A SEPARATE
CIRCUIT FROM PUMPS.
®
INSTRUCTIONS.
-ORMECHANICAL ALTERNATOR
(10-0075) WITH ALARM
CONTACTS.
MAIL TO: P.O. BOX 16347 • Louisville, KY 40256-0347
SHIP TO: 3649 Cane Run Road • Louisville, KY 40211-1961
(502) 778-2731 • 1 (800) 928-PUMP • FAX (502) 774-3624
Your Peace of Mind is Our Top Priority ®
© Copyright 2012 Zoeller Co. All rights reserved.
sk313
visit our web site:
www.zoeller.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising