PL370/470 Cradle - JM partners.CZ, sro

PL370/470 Cradle - JM partners.CZ, sro
PL370/470 Cradle
Quick Reference Guide
2
PL370/470 Cradle
© 1999 - 2006 SYMBOL TECHNOLOGIES, INC. All rights reserved.
Symbol reserves the right to make changes to any product to improve reliability,
function, or design.
Symbol does not assume any product liability arising out of, or in connection with,
the application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise
under any patent right or patent, covering or relating to any combination, system,
apparatus, machine, material, method, or process in which Symbol products
might be used. An implied license exists only for equipment, circuits, and
subsystems contained in Symbol products.
Symbol and the Symbol logo are registered trademarks of Symbol Technologies,
Inc. Other product names mentioned in this manual may be trademarks or
registered trademarks of their respective companies and are hereby
acknowledged.
Symbol Technologies, Inc.
One Symbol Plaza
Holtsville, N.Y. 11742-1300
http://www.symbol.com
Warranty
For the complete Symbol hardware product warranty statement, go to:
http://www.symbol.com/warranty.
Patents
This product is covered by one or more patents. For patent information go to:
http://www.symbol.com/patents.
Quick Reference Guide
3
Introduction
The PhaserLink 370/470 Radio Frequency (RF) cradle acts as a stand, host
communication interface and a charger for the Phaser RF scanner. For
convenience, the cradle can sit on a desktop or be mounted on a wall.
The cradle receives data from the scanner via radio frequency (RF) transmissions
through the antenna, then transmits that data to the host device through an
attached cable. The cradle also charges the scanner’s battery pack (in the
scanner).
Two versions of the cradle are available:
•
•
PL470 cradle: radio retail version.
PL370 cradle: radio industrial version.
This Quick Reference Guide provides basic instruction on the set up and use of
the cradle. Unless otherwise noted, the term PhaserLink refers to all versions of
the cradle.
Equipment Supplied
The following equipment is supplied:
-
Two Screws (for wall mounting).
One Velcro strip (for desk mounting).
Four rubber feet (for desk mounting).
This Quick Reference Guide.
PhaserLink cradle.
Save the shipping container for storing or shipping. Inspect all your equipment for
damage. If anything is damaged or missing, call your authorized Customer
Support Representative immediately.
Related Documentation
-
P370/470 RF Scanner Product Reference Guide, p/n 72-38495-xx
P370/470 RF Scanner Quick Reference Guide, p/n 72-38493-xx.
4
PL370/470 Cradle
Parts
Antenna
Pairing Label
Scanner
Support Tab
Charging/
Communication
Contacts
COM 1 Port
Power
Port
Charging
LED
Wall-mounting
Socket 1
Wall-mounting
Socket 2
Connecting to the Host
COM1
Power Port
To connect the cradle to a host:
1. Insert the appropriate interface cable from
the host computer into the COM1 port.
2. Connect the power connector of the power
supply (p/n 50-19000-101) into the cradle
power port. (The cradle cannot be powered
by the host computer.)
3. Connect the appropriate line cord to the
power supply and the other end to an AC
power source.
Quick Reference Guide
5
Wall Mounting
Before wall-mounting the cradle, the scanner support tab must be changed from
the desk-mount position to the wall-mount position..
1
1. Lift the scanner support tab out of
2.
3.
Desk Mount
Wall Mount
2
4.
Cable
Grooves
5.
3
6.
the top part of the cradle and
replace it in the wall-mount
position as shown.
Seat the cables from the bottom of
the cradle in the grooves along the
length of the cradle so that the
bottom of the cradle is smooth and
flat.
Secure two screws (included) to
the wall. A template is provided on
page 14.
- Fasten the screws provided
into the wall where the cradle
should hang, leaving about 1/8”
(0.3 cm) of the screw outside
the wall for the cradle wall
mounting sockets.
Place the cradle over the screw
heads and slide down until it fits
into place. Slight pressure
upwards should not move the
cradle.
Position the antenna vertically,
pointing toward the ceiling.
Place the Phaser scanner in the
cradle.
6
PL370/470 Cradle
Inserting Phaser in the Cradle
Place the Phaser scanner in the cradle so that the top of the scanner sits in the
larger part of the cradle and the metal contacts on the bottom of the scanner touch
the contacts on the cradle.
Pairing
The wireless connection between the scanner and cradle is the low power radio
transmission through RF transceivers in both the scanner and cradle.
Communication consists of bidirectional message packets. However, the scanner
and cradle must be paired for this communication to work.
NOTE After a new host is installed at the cradle, re-scan the pairing bar
code. This allows the cradle to notify the scanner of the change in
the host device.
To pair the scanner with the cradle:
1. Scan the pairing bar code on the top of the cradle. A duplicate pairing bar code
is located in the well on the bottom of the cradle.
2. Insert the scanner into the cradle (recommended but not required). Note that
data cannot be scanned until linking (pairing) is complete.
3. During pairing there is an exchange of information between the scanner and
the cradle. This occurs in a few seconds if the scanner is in the cradle and over
a minute if the scanner is not in the cradle.
4. After the exchange is complete, the scanner and cradle are paired. Successful
pairing is indicated by a warble beep; failure, or unsuccessful pairing, is
indicated by a low/high beep.
Sending Data to the Host Computer
The cradle receives data from the scanner and transmits it to the host computer
via the interface cable.
Recharging the Battery in the Phaser
To charge the scanner’s battery, place the scanner in the cradle ensuring the
metal contacts on the bottom of the scanner touch the contacts on the cradle. A
Quick Reference Guide
7
complete charge takes up to 4 hours, depending upon the remaining charge in the
battery.
Charging LED
Once the scanner is placed in the cradle, it waits 15 minutes to start charging the
battery in the scanner. The LED indicates the charging status as follows:
LED
Description
Off
The scanner is not in the cradle.
Slow Blink
Scanner is in cradle but not charging.
Fast Blink
Scanner is in cradle and charging.
On
Scanner is in cradle and the charge cycle is
complete.
Troubleshooting
If the cradle does not work after following the operating instructions in this guide:
•
•
•
check the system power.
check for loose cable connections.
ensure the scanner is sitting properly in the cradle.
Cleaning
Wipe the cradle periodically with a lens tissue or other material suitable for
cleaning optical material, such as eyeglasses.
CAUTION Do not pour, spray or spill any liquid on the cradle.
Regulatory Information
All Symbol devices are designed to be compliant with rules and regulations in locations they are sold
and are labeled as required.
Any changes or modifications to Symbol Technologies equipment, not expressly approved by Symbol
Technologies, could void the user's authority to operate the equipment.
CAUTION Only use Symbol approved and UL Listed accessories, battery packs and
battery chargers.
Do NOT attempt to charge damp/wet mobile computers or batteries. All components must be dry
before connecting to an external power source.
Country Approvals
Regulatory markings are applied to the device signifying the radio (s) are approved for use in the
following countries: United States, Canada, Australia, Japan and Europe.
Please refer to the Symbol Declaration of Conformity (DoC) for details of other country markings.
This is available at http://www2.symbol.com/doc/.
Operation of the device without regulatory approval is illegal.
8
PL370/470 Cradle
Health and Safety Recommendations
Ergonomic Recommendations
-
CAUTION In order to avoid or minimize the potential risk of ergonomic injury follow the
recommendations below. Consult with your local Health & Safety Manager to
ensure that you are adhering to your company's safety programs to prevent
employee injury.
Reduce or eliminate repetitive motion.
Maintain a natural position.
Reduce or eliminate excessive force.
Keep objects that are used frequently within easy reach.
Perform tasks at correct heights.
Reduce or eliminate vibration.
Reduce or eliminate direct pressure.
Provide adjustable workstations.
Provide adequate clearance.
Provide a suitable working environment.
Improve work procedures.
Vehicle or Forklift Installation
RF signals may affect improperly installed or inadequately shielded electronic systems in motor
vehicles (including safety systems). Check with the manufacturer or its representative regarding your
vehicle. You should also consult the manufacturer of any equipment that has been added to your
vehicle.
Position your device within easy reach. Be able to access your device without removing your eyes
from the road.
Warnings for Use of Wireless Devices
Please observe all warning notices with regard to the usage of wireless devices.
Potentially Hazardous Atmospheres
You are reminded of the need to observe restrictions on the use of radio devices in fuel depots,
chemical plants etc. and areas where the air contains chemicals or particles (such as grain, dust, or
metal powders) and any other area where you would normally be advised to turn off your vehicle
engine.
Safety in Hospitals
Wireless devices transmit radio frequency energy and may affect medical electrical equipement.
Wireless devices should be switched off wherever you are requested to do so in hospitals, clinics or
healthcare facilitlies. These requests are designed to prevent possible interference with sensitive
medical equipement.
Pacemakers
Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between
a handheld wireless device and a pacemaker to avoid potential interference with the pacemaker.
These recommendations are consistent with independent research and recommendations by
Wireless Technology Research.
Quick Reference Guide
9
Persons with Pacemakers:
- Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when
turned ON
- Should not carry the device in a breast pocket
- Should use the ear furthest from the pacemaker to minimise the potential for interference.
If you have any reason to suspect that interference is taking place, turn OFF your device.
Hearing Aids
The wireless device may interfere with some hearing aids. In the event of interference you may want
to consult your hearing aid supplier to discuss solutions.
Other Medical Devices
Please consult your physician or the manufacturer of the medical device, to determine if the
operation of your wireless product may interfere with the medical device.
FCC / EU RF Exposure Guidelines
Safety Information
The device complies with Internationally recognised standards covering Specific Absorption Rate
(SAR) related to human exposure to electromagnetic fields from radio devices.
Reducing RF Exposure - Use Properly
It is advisable to use the device only in the normal operating position.
Handheld Devices
To comply with FCC RF exposure requirements, this device must be operated in the hand with a
minimum separation distance of 20 cm or more from a person's body. Other operating configurations
should be avoided.
Laser Devices
Complies with 21CFR1040.10 and 1040.11 except for deviations pursuant to Laser Notice
No. 50, dated July 26, 2001.
EN60825-1:1994+ A1:2002 +A2:2001
IEC60825-1:1993+A1:1997+A2:2001
The laser classification is marked on one of the labels on the device.
Class 1 Laser devices are not considered to be hazardous when used for their intended purpose.
The following statement is required to comply with US and international regulations:
CAUTION Use of controls, adjustments or performance of procedures other than those
specified herein may result in hazardous laser light exposure.
Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such
as the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class
2 laser is not known to be harmful.
Laser Labeling
In accordance with Clause 5, IEC 825 and EN60825, the following information is provided to the user:
ENGLISH
CLASS 1
CLASS 2
HEBREW
CLASS 1 LASER PRODUCT
LASER LIGHT
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
10
PL370/470 Cradle
DANISH / DANSK
KLASSE 1
KLASSE 1 LASERPRODUKT
KLASSE 2
LASERLYF
SE IKKE IND I STRÅLEN
KLASSE 2 LASERPRODUKT
ITALIAN / ITALIANO
CLASSE 1
PRODOTTO AL LASER DI CLASSE 1
CLASSE 2
LUCE LASER
NON FISSARE IL RAGGIOPRODOTTO
AL LASER DI CLASSE 2
DUTCH / NEDERLANDS
KLASSE 1
KLASSE-1 LASERPRODUKT
KLASSE 2
LASERLICHT
NIET IN STRAAL STAREN
KLASSE-2 LASERPRODUKT
NORWEGIAN / NORSK
KLASSE 1
LASERPRODUKT, KLASSE 1
KLASSE 2
LASERLYS IKKE STIRR INN I LYSSTRÅLEN
LASERPRODUKT, KLASSE 2
FINNISH / SUOMI
LUOKKA 1
LUOKKA 1 LASERTUOTE
LUOKKA 2
LASERVALO
ÄLÄ TUIJOTA SÄDETTÄ
LUOKKA 2 LASERTUOTE
PORTUGUESE / PORTUGUÊS
CLASSE 1
PRODUTO LASER DA CLASSE 1
CLASSE 2
LUZ DE LASER NÃO FIXAR O RAIO LUMINOSO
PRODUTO LASER DA CLASSE 2
FRENCH / FRANÇAIS
CLASSE 1
PRODUIT LASER DE CLASSE 1
CLASSE 2
LUMIERE LASER
NE PAS REGARDER LE RAYON FIXEMENT
PRODUIT LASER DE CLASSE 2
SPANISH / ESPAÑOL
CLASE 1
PRODUCTO LASER DE LA CLASE 1
CLASE 2
LUZ LASER
NO MIRE FIJAMENTE EL HAZ
PRODUCTO LASER DE LA CLASE 2
GERMAN / DEUTCH
KLASSE 1
LASERPRODUKT DER KLASSE 1
KLASSE 2
LASERSTRAHLEN
NICHT DIREKT IN DEN LASERSTRAHL SCHAUEN
LASERPRODUKT DER KLASSE 2
SWEDISH / SVENSKA
KLASS 1
LASERPRODUKT KLASS 1
KLASS 2
LASERLJUS STIRRA INTE MOT STRÅLEN
LASERPRODUKT KLASS 2
CHINESE / ㅔԧЁ᭛
1㉏
1㉏▔‫ܝ‬ѻક
2㉏
▔‫ܝ‬
ߛ࣓⊼㾚‫ܝ‬ᴳ
2㉏▔‫ܝ‬ѻક
KOREAN /G䚐ạ㛨
X☥ἽG
X☥ἽG⤼㢨㤴G㥐䖼
Y☥ἽG
⤼㢨㤴Gṅ㉔
GG
㢨Gṅ㉔㡸G㨰㐐䚌㫴G⫼㐡㐐㝘U
GG
Y☥ἽG⤼㢨㤴G㥐䖼
JAPANESE / ᣣᧄ⺆
ࠢ࡜ࠬ‫⵾ࠩ࡯࡟ࠬ࡜ࠢޓ‬ຠ
ࠢ࡜ࠬ‫ࠩ࡯࡟ޓ‬శ✢
శ✢ࠍ⋥ⷞߒߥ޿ߢߊߛߐ޿
ࠢ࡜ࠬ࡟࡯ࠩ⵾ຠ
Power Supply
Use only a Symbol approved power supply 50-14000-101R output rated 9 Vdc and minimum 1 A.
The power supply is certified to EN60950-1 with SELV outputs. Use of an alternative power supply
invalidates any approval given to this device and may be dangerous.
Batteries
Please follow the local regulations when disposing of re-chargeable batteries.
Taiwan - Recycling
EPA (Environmental Protection Administration) requires dry battery producing or importing firms in
accordance with Article 15 of the Waste Disposal Act are required to indicate the recycling marks on
the batteries used in sales, giveaway or promotion. Contact a qualified Taiwanese recycler for proper
battery disposal.
Quick Reference Guide
11
Symbol Rechargeable Batteries
Symbol rechargeable battery packs are designed and constructed to the highest standards within the
industry. However, there are limitations to how long a battery can operate or be stored before needing
replacement. Many factors affect the life of a battery pack such as heat, cold, customer usage
profiles, age, and severe drops.
When batteries are stored over a year, battery cell manufacturers advise that some irreversible
deterioration in overall battery quality may occur. To minimize this loss, they recommend storing
batteries half charged in a dry, cool place between 41° and 77°F (5° and 25°C), the cooler the better)
and removed from the equipment to prevent the loss of capacity. Batteries should be charged to half
capacity at least once a year. If an electrolyte leakage is observed, avoid any contact with the
affected area and properly dispose of the battery.
Replace the battery when a significant loss of run time is detected. Batteries must be charged within
the 32° to 104°F (0° to 40°C) temperature range.
The standard warranty period for all Symbol batteries is 30 days, regardless if the battery was
purchased separately or included as part of the mobile computer. For more information on Symbol
batteries, please visit http://mysymbolcare.symbol.com/battery/batbasics1.html.
Radio Frequency Interference Requirements-FCC
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
FOR HOME OR OFFICE USE
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Tested to comply
with FCC Standards
Radio Transmitters (Part 15)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Radio Frequency Interference Requirements - Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Radio Transmitters
This device complies with RSS 210 of Industry & Science Canada. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Label Marking: The Term "IC:" before the radio certification only signifies that Industry Canada
technical specifications were met.
12
PL370/470 Cradle
Marking and European Economic Area (EEA)
2.4GHz devices for use through the EEA have the following restrictions:
- Maximum radiated transmit power of 10 mW EIRP in the frequency range 2.400 -2.4835 GHz
- France, equipment is restricted to 2.446 -2.454 GHz frequency range
- Italy requires a user license for outside usage.
Statement of Compliance
Symbol Technologies, Inc., hereby, declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC. A Declaration of Conformity may
be obtained from http://www2.symbol.com/doc/.
Brazil
Declarações Regulamentares para P370, P470 PL370 y PL470 BRAZIL
NOTA: A marca de certificação se aplica ao Equip. de Radiação Restrita, model P470 y PL470. Este
equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência
prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas
operando em caráter primário."
Para maiores consultas sobre ANATEL consulte o site: www.anatel.gov.br
The following signifies approval in Brazil.
Waste Electrical and Electronic Equipment (WEEE)
English: For EU Customers: All products at the end of their life must be returned to Symbol for
recycling. For information on how to return product, please go to:
http://www.symbol.com/environmental_compliance.
Dansk: Til kunder i EU: Alle produkter skal returneres til Symbol til recirkulering, når de er udtjent.
Læs oplysningerne om returnering af produkter på:
http://www.symbol.com/environmental_compliance.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer Lebensdauer zum
Recycling an Symbol zurückgesandt werden. Informationen zur Rücksendung von Produkten finden
Sie unter http://www.symbol.com/environmental_compliance.
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise eesmärgil
Symbol'ile. Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun aadressi:
http://www.symbol.com/environmental_compliance.
Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Symbol al
final de su ciclo de vida para que sean reciclados. Si desea más información sobre cómo devolver un
producto, visite: http://www.symbol.com/environmental_compliance.
Quick Reference Guide
13
Français : Clients de l'Union Européenne : Tous les produits en fin de cycle de vie doivent être
retournés à Symbol pour recyclage. Pour de plus amples informations sur le retour de produits,
consultez : http://www.symbol.com/environmental_compliance.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono
essere restituiti a Symbol al fine di consentirne il riciclaggio. Per informazioni sulle modalità di
restituzione, visitare il seguente sito Web: http://www.symbol.com/environmental_compliance.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Symbol vállalathoz kell eljuttatni
újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos tudnivalókért látogasson
el a http://www.symbol.com/environmental_compliance weboldalra.
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar
Symbol te worden teruggezonden voor recycling. Raadpleeg
http://www.symbol.com/environmental_compliance voor meer informatie over het terugzenden van
producten.
Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à Symbol
para reciclagem. Para obter informações sobre como devolver o produto, visite:
http://www.symbol.com/environmental_compliance.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju Symbol za
reciklažo. Za informacije o vraèilu izdelka obišèite:
http://www.symbol.com/environmental_compliance.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi
Symbol-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on osoitteessa
http://www.symbol.com/environmental_compliance.
Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till Symbol
för återvinning. Information om hur du returnerar produkten finns på
http://www.symbol.com/environmental_compliance.
14
PL370/470 Cradle
Wall Mounting Template
1.27”
Wall
Mounting
Socket 1
Use 1/8” drill bit
for screw holes.
Center
Line of
Cradle
3.85”
Wall
Mounting
Socket 2
Quick Reference Guide
This page is intentionally blank.
15
Service Information
Before you use the unit, it must be configured to operate in your facility’s network
and run your applications.
If you have a problem running your unit or using your equipment, contact your
facility’s Technical or Systems Support. If there is a problem with the equipment,
they will contact the Symbol Support Center:
United States
United Kingdom
Australia
Denmark/Danmark
France
1-800-653-5350
0800 328 2424
1-800-672-906
7020-1718
01-40-96-52-21
Italy/Italia
Netherlands/Nederla
nd
South Africa
Sweden/Sverige
2-484441
315-271700
Latin America
Sales Support
Canada
Asia/Pacific
Austria/Österreich
Finland/Suomi
Germany/
Deutschland
Mexico/México
Norway/Norge
11-809 5311
08 445 29 00
Spain/España
Europe/Mid-East
Distributor
Operations
Inside USA: 1-800-347-0178;
Outside USA: +1.954.255.2610
905-629-7226
337-6588
01-5055794-0
9 5407 580
6074-49020
5-520-1835
+47 2232 4375
+913244000
Contact local
distributor or call
+44 118 945 7360
For the latest version of this guide go to: http://www.symbol.com/manuals.
72-38494-01
Revision C - May 2006
Symbol Technologies, Inc.
One Symbol Plaza Holtsville, N.Y. 11742-1300
http://www.symbol.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising