XK1-FODL ENHANCED sd20060627.cdr

XK1-FODL ENHANCED sd20060627.cdr
Platform # 01
Firmware: FODL
Installation
Manual (1/2 Pages)
Description: Ford Doorlock and Alarm Interface (NO KEY REQUIRED)
Functions: Lock/Unlock, Power Sliding Doors (Lt & Rt), OEM Security Arm/Disarm, Door Sense Trigger Output(-), Trunk (Lincoln LS ONLY)
Downloadable Firmware for Platform #01: AMDL, FODL, GMDL6, GMDL7, HODL4, HYDL, KIADL, KIADL2, TOYDL, VWDL, VWDL2
WARNING: Before beginning your install go to www.XpressDownload.com and be sure to print the LATEST corresponding installation manual
for the firmware that is flashed to the platform you are using.
Section A
See Wire Connection Guide for detailed information regarding wire functionality
Lock
Blue
Unlock
OUTPUT
(-)
Violet/White
Door SenseTrigger
Violet
Data
INPUT
DATA
INPUT
(-)
Pink/White
Driver’s Side Sliding Door
INPUT
(-)
Pink
Passenger Side Sliding Door
INPUT
(-)
Orange
Trunk Input (See Wire Guide)
INPUT
(+)
Red
(+)12 Volt Constant
INPUT
(-)
Black
Chassis Ground
KEYLESS / STARTER/ ALARM
(-)
(-)
Green
INPUT
Ground When Running
RCS
Brown
D2D
Blue
Option B - Data 2 Data connection to RCS Data Port
REMOTE CONTROL SYSTEM
10 PIN HARNESS
LED
USB Cable
USB Adaptor
CLEARCODE VIP
DATA PORT
(-)
INPUT
UPGRADEABLE
DOOR LOCK
&
OEM ALARM
INTERFACE
MODULE
Brown
D2D
4 PIN DATA TO DATA (D2D) CABLE (OPTIONAL ACCESSORY)
Internet
P.C.
Option A
Firmware Upgrades
DC
+12V
Programming
button
Data Wire Connects to OBDII PIN 2
“Fig. 1”
Section B
WIRE GUIDE: CONNECTIONS
D2D = Optional use of 4 Pin Data to Data (D2D) cable will replace the analogue wire (w2w) connection
10 PIN HARNESS
(-)
WIRE
I/O
Connect
D2D
SPECIFIC WIRE CONNECTION LOCATION
PIN# COLOR w2w STATUS /(+) Location
D2D
(-)
Ground
When Running output of remote starter
1 Brown
RCS
w2w Input
ACTIVATION and/or FUNCTIONALITY
Lock/Unlock + OEM Security Arm/Disarm
2
Green
D2D
w2w
Input
(-)
RCS
Connect to (-) Lock Ouput wire of RCS
Lock All Doors
3
Blue
D2D
w2w
Input
(-)
RCS
Connect to (-) Unlock Output wire of RCS
Unlocks All Doors
4
Violet/
White
D2D
w2w
Output (-)
RCS
Door Sense Trigger connects to (-) door trigger input Detects Doors status (open/closed) via data bus then
wire of RCS
converts to an analogue output (-)
5
Violet
w2w
6
Pink/
White
7
Pink
8
Orange
Data
Vehicle
On Board Diagnostic Connector (OBDII) PIN2 Located
Under Dash on Driver Side (See Fig.1)
Data Commands from Module to Vehicle
D2D
w2w
D2D
w2w
Input
(-)
RCS
AUX Output for Driver’s Side Sliding Door
1 sec (-) Pulse Driver’s Side Door Open/Close (Ford Windstar ONLY)
Input
(-)
RCS
AUX Output for Passenger’s Side Sliding Door
1 sec (-) Pulse Passenger’s Side Door Open/Close (Ford Windstar ONLY)
D2D
w2w
Input
(-)
RCS
Connect to (-) Trunk Release Output wire of RCS
Trunk Release (Lincoln LS ONLY)
9
Red
D2D
w2w
Input
(+)
Vehicle
Constant (+) 12 Volt Source
Power Source
10
Black
D2D
w2w
Input
(-)
Vehicle
Chassis Ground
Ground Source
Legend
RCS = Remote Control System
N/C = No Connection
N/A = Not Applicable
w2w= analogue wire to wire
D2D= data 2 data
DATA to DATA PORT (D2D): Blue connector of D2D Cable plugs into the upgradeable vehicle interface module.
OPTION A: - D2D Port used to connect to USB Bootloader adaptor & computer to download & flash vehicle interface firmware.
OPTION B: - D2D Port used to connect to the data port of a remote control system equipped with ClearCode Vehicle Interface Protocol.
Remote control systems designed with ClearCode VIP can securely communicate via the D2D cable to transmit & receive data commands which initiate
specific vehicle function such as doorlocks & immobilizer override and /or request information from the vehicle such as status of entry points (doors) or
ambiant température, diesel glow plug etc… ClearCode VIP represents the doorway to vehicle integration...
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall
the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or
any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.:Under no circumstances shall the manufacturer and distributors of this product are liable for consequential damages sustained in
connection with this product neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.
Platform # 01
Firmware: FODL
Installation
Manual (2/2 Pages)
Description: Ford Doorlock and Alarm Interface (NO KEY REQUIRED)
Functions: Lock/Unlock, Power Sliding Doors (Lt & Rt), OEM Security Arm/Disarm, Door Sense Trigger Output(-), Trunk (Lincoln LS ONLY)
Section C
VEHICLE PROGRAMMING:
Once the module has been properly connected, turn key to ON position. Horn will honk 1 to 5 times and/or parking lights will flash indicating a successful
connection.
Section D
USER SETTINGS - OPTIONAL PROGRAMMING:
USER MODES are identified by a slow LED flash pattern. 1 slow flash=Mode1, 2 slow flashes=Mode 2 etc.
1) Key “OFF” position, press and hold program button for 2 seconds, LED will flash rapidly for 2 seconds. Release button, LED will identify the MODE
selection with a slow flash pattern (1- 8 slow flashes) and then will identify OPTION selection with a fast flash pattern. (1 or 2 fast flashes)
2) To change MODE, push button one time, LED will confirm MODE with slow flash pattern (1-8 slow flashes).
3) To change OPTION SELECTION within a MODE, press LOCK or UNLOCK button on the aftermarket remote control system. LED will identify option
selection with either one or two fast flashes.
4) To save and exit programming, press and hold button until LED flashes one time rapidly, showing end of OPTION programming.
* = Default
MODE 1 =
*OPTION 1: 1st Pulse Unlock All Doors (Default) OPTION 2: 1st Pulse Unlock Driver Door, 2nd Pulse Unlock All Doors
Reset MODE 8 = Press lock or unlock button on aftermarket remote, LED will flash 8 times slowly and twice rapidly. Push programming
button 1 time, LED will flash one time. Reset is complete.
Section E
VEHICLE COMPATIBILITY CHART
VEHICLE
Ford Windstar
Lincoln LS
2003
ü
ü
2002
ü
ü
2001
ü
ü
2000
ü
ü
1999
ü
N/A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising