User manual | Toro Super 600 sprinkler Installation and service instructions

 INSTALLATION AND SERVICE INSTRUCTIONS
Super 600 Sprinkler
Introduction
Super 600 Sprinklers utilize a permanently sealed and lubricated gear drive assembiy for smooth, vibration free
performance and dependability. Available in 2" Pop-up, the Super 600 is designed for residential or commer-
cial applications and works well in problem areas involving low pressure, sandy water, and debris.
Model Numbers / Performance Charts Specifications
BODY NOZZLE PRECIP. RATE" m Iniet Threads — 3/4" NPT Female
STYLE ARC SIZE PSI GPM RAD 90° 180 20 a Cap Diameter — 3"
o y a Ye Si a Body Height — 6-1/4"
$600 PC 1.3 35 136 38 134 3 3 m Pop-Up to Nozzle — 2"
S600 FC 13 40 1.45 39 36 § € m Operating Pressure — 25 to 50 PSI
45 153 39 36 E E
50 1681 40° 138 2 o s Maximum Pressure — 75 PSI
25 238 41 52 26 ae
30 256 42 52 26 2
S600 PC 25 35 277 43 56 28 1
S600 FC 25 40 294 44 56 28 8
45 3.14 45 56 .28 =
50 334 45 60 30 =
25 482 38 1.24 62 31
30 5.19 42 1.08 54 27
S600 PC 5.0 35 569 45 1.04 52 26
S600 FC 5.0 40 6.07 47 1.00 50 25
45 6.41 48 1.04 52 26
50 671 50° 1.00 50 25
* Precipitation Rates:
Square spacing, shown in inches per hour, calculated at 50% of
diameter.
Triangular spacing, shown in inches per hour, calculated at 55%
of diameter.
+ Not recommended at this pressure without using nozzle stream
breaker adjustment screw.
Rubber Cover Kit
Attach rubber cover (optional) to sprinkler cap, using Loctite Super Bonder* 414 adhe-
sive (or equivalent) as follows:
1. Assure bonding surfaces are dry and free of dirt, grease, and foreign substances.
E
2. Spread thin film of adhesive on underside of rubber cap cover and rubber nozzle (ES)
cover.
3. Assemble immediately. Press retainer plug pins into two (2) holes in nozzle. (See
Figure 1 and Parts Breakout.)
4. Apply firm pressure until set (approximately 15 seconds).
Installation Procedure
The Super 600 Lawn sprinkler should be installed using an adjustable riser method as illustrated below. The
adjustable riser permits easier sprinkler positioning and provides protection from damage due to displacement
by foot traffic or turf maintenance equipment.
1.
>
FIGURE 2
Prior to sprinkler head installation, flush lines thoroughly to eliminate all dirt and debris from system.
TORO
FUNNY PIPE
FITTING
FUNNY PIPE
TORO
SADDLE TEE
Caution
Use only teflon tape on threaded connections between body and riser. Deterioration of plas-
tic body may occur if other sealing compound types are used.
Install sprinkler using one of two methods illustrated above. Lawn sprinklers are correctly positioned when
top of cap is level with finished grade. Rotate nozzles of part circle heads counterclockwise to left stop.
Screw sprinkler body onto riser aligning nozzle port with left border of coverage area. Do not over torque,
hand tight is sufficient.
Turn on water to system.
Observe part circle arc patterns and adjust as necessary. (See Part Circle Adjustment.)
Observe spray pattern radius and adjust as necessary. (See Spray Radius Adjustment.)
Part Circle Arc Adjustment
Note: Left side of arc is non-adjustable and will change only if sprinkler body is turned on riser. Right side of
arc is adjustable to produce a spray arc from 45° minimum to 315° maximum. It is recommended that arc pat-
tern be adjusted during sprinkler operation, however, the Super 600 can be adjusted when not in operation.
. Turn on water to sprinkler.
Rotate nozzle left and right to check arc setting.
Note: Do not forcibly turn nozzle. Always turn nozzle in direction of least resistance.
Rotate nozzle counterclockwise to left stop. Since left stop is non-adjustable, align spray with left side of
watering area by turning sprinkler body in ground.
Note: This procedure must be accomplished before increasing or decreasing arc pattern.
To increase or decrease arc, follow directions shown in Figure 3.
Note: A small screwdriver or similar tool is required to depress adjustment button (located at top of drive
assembly) when adjusting arc pattern.
FIGURE 3
D 7 — DESIRED RIGHT
EXAMPLE To Increase Arc
CURRENT ARC
INCREASE (A) Start with nozzle at left stop.
7 THIS (B) Press and hold adjustment button down. Rotate
\ AMOUNT nozzle clockwise to desirea amount of arc
— increase, then release adjustment button.
(C) Arc increase will automatically be added to right
To Decrease Arc
(A) Start with nozzle at right stop.
CURRENT ARC
~~ DESIRED RIGHT
TRAVEL LIMIT travel limit as shown below.
X AMOUNT WILL RESULT
A ARC IS IN ARC
! ADJUSTED INCREASE
< HERE 644999004 a «sn HERE
| $1
; { DL —- —
EXAMPLE
TRAVEL LIMIT (B) Press and hold adjustment button down. Rotate
nozzle counterclockwise to desired amount of arc
DECREASE decrease, then release adjustment button.
AMOUNT (C) Arc decrease will provide desired right travel limit.
ARC
ADJUSTMENT
REQUIRED
|
DESIRED C
RIGHT
STOP
Spray Radius Adjustment
A stream breaker screw, accessible from top of nozzle with a 1/16" hex driver, is pro-
vided to shorten radius and/or diffuse spray.
Note: To prevent a possible dry area around head when operating at low pressure,
adjust stream breaker to slightly diffuse spray.
Caution
Stream breaker screw will fall into water stream if decrease adjustment
is excessive. Replacement will be necessary.
To Decrease Radius
1. Rotate stream breaker screw clockwise. (See Figure 4.)
To Increase Radius
1. Rotate stream breaker screw counterclockwise. (See Figure 4.)
1/16" НЕХ
DRIVER
INCREASE
DECREASE
FIGURE 4
Sprinkler Maintenance and Service
Cleaning Pop-Up Sprinkler Heads
1. Unscrew cap while holding sprinkler body to avoid changing alignment (part circle models).
2. Remove cap, nozzle and drive assembly from body noting nozzle alignment for proper reassembly (part cir-
cle models).
м о о во
Changing Nozzles
Note: Prior to removal and replacement of nozzle, follow Steps 1 through 4 in
section on “Cleaning Pop-Up Sprinkler Heads".
1. Push cap down, compressing return spring to expose set screw in nozzle.
2. Loosen set screw (see Figure 5) and unscrew nozzle from drive assembly.
3. Screw new nozzle onto drive assembly (do not over tighten). Secure nozzle with
set screw (do not over tighten).
4. Release cap SLOWLY to avoid injury.
Remove basket screen and flush thoroughly to eliminate all dirt and debris.
Inspect stator and clean thoroughly as required.
Reinstall basket screen.
Flush body thoroughly prior to reassembly.
Reinstall cap, nozzle and drive assembly aligning keyways for proper nozzle position (hand tighten).
17167 HEX
DRIVER
FIGURE 5
Нет
Nomenclature
Quantity
Per Assy.
ya
о © ю ча с во ООО 0 0 п = — |5
NS
Plug, Retainer
Plug, Retainer
Cover, Rubber
Nozzle Assy., PC 1.3 (Includes item 4)
Nozzle Assy., PC 2.5 (Includes item 4)
Nozzte Assy., PC 5.0 (Includes item 4)
Nozzie Assy., FC 1.3 (Includes Item 4)
Nozzle Assy., FC 2.5 (Includes item 4)
Nozzle Assy., FC 5.0 (Includes item 4)
Screw, Set, Half Dog Point
Seal, Nozzle
Cap
Seal, Riser
Spring, Retraction
Drive Assy., Full Circle
Drive Assy., Part Circle, Adjustable
Stator Assy., Variable
(Includes items 10 and 11)
Sleeve, Stator
Diaphragm, Stator
Screen
Body
Service [tems
Kit, Cover Rubber
(includes ltems 1, 2 and 6)
Kit, Check Valve
(Includes item 12)
Low Flush Seal, S600
ak m — — = = Л) eh mk md rd rd bh anh ok
—— o — == =
NIN NA AMA Pa 7
A d Fu 1% PA E | e E e e e e geen Aes A RIA
areal a pre a NA A
ge RE KH RA EN PE