OPERATOR`S AND PARTS MANUAL WLA 213 Series Hydraulic

OPERATOR`S AND PARTS MANUAL WLA 213 Series Hydraulic
1
OPERATOR’S AND PARTS MANUAL
WLA 213 Series
Hydraulic Windrow Sweeper
for Loaders
Serial Number: ___________________
Model Number: ___________________
800-456-7100 I www.paladinattachments.com
Manual Number: 51-4005
Release Date: April 2015
Serial Number: 0733001 & Up
Rev. 1
2800 N. Zeeb Rd., Dexter, MI. 48130, United States of America Copyright ©
2
3
Table of Contents
Section 1 ... Installation.................................................... 5-13
Section 2 ... Operation and Maintenance...................... 15-22
Section 3 ... Service......................................................... 23-33
Section 4 ... Parts............................................................ 35-46
Section 5 ... Options........................................................ 47-55
Section 6 ... Appendix..................................................... 57-61
4
5
Installation Manual
Table of Contents
Introduction................................................................ 6
Safety Information.................................................7-13
General Safety Information.....................................7-8
Safety Signs & Labels......................................... 10-11
Product Information Section..................................... 12
Installation/Storage.................................................. 13
6
SAFETY SECTION
INTRODUCTION
Introduction
Contacting SWEEPSTER
Importance of this Manual
If you have any questions about information in this manual or
need to order parts, please call, write, fax or e-mail
SWEEPSTER.
Read this manual before attempting to operate
the equipment.
This operator’s manual should be regarded as part of the
sweeper. Suppliers of both new and secondhand sweepers are
advised to keep documentation indicating that this manual was
provided with the sweeper.
The manual contains information regarding installation,
operation and maintenance required for this sweeper and optional equipment. It also includes detailed parts lists.
Purpose of Sweeper
This sweeper is designed solely for use in construction cleanup,
road maintenance, grounds maintenance and similar
operations. Use in any other way is considered contrary to the
intended use. Compliance with and strict adherence to
operation, service and repair conditions, as specified by the
manufacturer, are also essential elements of the intended use.
This sweeper should be operated, serviced and repaired only
by persons who are familiar with its characteristics and
acquainted with relevant safety procedures.
Accident prevention regulations, all other generally
recognized safety regulations and all road traffic regulations
must be observed at all times.
Any modifications made to this sweeper may relieve the
manufacturer of liability for any resulting damage or injury.
SWEEPSTER
2800 North Zeeb Road
Dexter, Michigan 48130
Phone: (734) 996-9116 - (800) 456-7100
FAX: (734) 996-9014
e-mail: [email protected]
For help with installation, operation or maintenance
procedures, contact our Technical Service Department. Direct
product questions and parts orders to our Sales Department.
When ordering parts or accessories, be prepared to give the
following information:
•Sweeper model, serial number and date of
purchase
•Prime mover, make and model
•Part number, description and quantity
Terms Used in Manual
Right-hand, left-hand, front and rear are determined from the
operator’s perspective (either the operator’s seat or standing
behind a walk-behind unit), facing forward in the normal
operating position.
Prime mover refers to the tractor, truck, loader or tow vehicle
that the sweeper is mounted on or towed by.
Safety Alert Symbol
Optional Equipment
This safety alert symbol indicates important safety messages in this manual. When you see this symbol, be
alert to the possibility of injury. Carefully read the message that
follows and inform other operators.
Installation instructions for optional equipment, if applicable,
appear in the Service Manual Section.
Specifications & Features
Due to continuous product improvement, specifications and
features may change without notice.
Warranty
To validate the warranty for this unit, fill out the warranty card or
warranty pages located at the back of this manual. Then, send
this information to SWEEPSTER.
7
SAFETY SECTION
GENERAL SAFETY INFORMATION
Safety Information
Read this manual
Read all safety information in this manual. All
operators must read and understand the entire
contents of this manual before sweeping.
General safety practices are listed on Safety
Information pages and specific safety
information is located throughout this manual.
Hazard Definitions
Four hazard classifications are used in this manual. They are
DANGER - Indicates an imminently hazardous
situation which, if not avoided, will result
in death or serious injury.
WARNING -Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury.
•Check prime mover tire pressure before sweeping.
•Check tire ratings to be sure they match the prime
mover load. Weigh the sweeper end of the prime
mover, if necessary, to insure proper tire rating.
• Remove from the sweeping area all property that
could be damaged by flying debris.
• Be sure all persons not operating the sweeper are
clear of the sweeper discharge area.
• Always wear proper apparel such as a long-sleeved
shirt buttoned at the cuffs; safety glasses, goggles
or a face shield; ear protection; and a dust mask.
While operating sweeper:
• When operating sweeper, adhere to all government
rules, local laws and other professional guidelines for
your sweeping application.
WARNING Never raise the sweeper more than a
few feet off the ground. The sweeper
can tip back or the prime mover can tip
over causing death or serious injury,
CAUTION -Indicates a potentially hazardous
situation which, if not avoided, may result
in minor or moderate injury.
• Before leaving the operator’s area for any reason, lower
the sweeper to the ground. Stop the prime mover
engine, set the parking brake and remove the key from
the ignition.
NOTICE - Used for instructions when machine
damage may be involved.
• Minimize flying debris - use the slowest rotating speed
that will do the job. See Operation Section: Operating
Tips
Operation
• Keep hands, feet, hair and loose clothing away from all
moving parts.
CAUTION - A sweeper is a demanding machine.
Only fully trained operators or trainee
operators under the close supervision of
a fully trained person should use this
machine.
Before operating sweeper:
• Leave the brush hood (shield) and all other shields and
safety equipment in place when operating the sweeper
and prime mover.
• Be aware of the extra weight and width a sweeper adds.
Reduce travel speed accordingly. See Product
Information Section: Operating the Sweeper.
•Learn sweeper and prime mover controls in an off-road
location.
• When sweeping on rough terrain, reduce speed to avoid
“bouncing” the sweeper. Loss of steering can result.
•Be sure that you are in a safe area, away from traffic or
other hazards.
• Never sweep toward people, buildings, vehicles or other
objects that can be damaged by flying debris.
•Check all hardware holding the sweeper to the prime
mover, making sure it is tight.
•Replace any damaged or fatigued hardware with
properly rated fasteners. See Maintenance Section
•Make sure all hydraulic hardware and hydraulic fittings
are tight.
•Only operate the sweeper while you are in the operating
position. The safety restraint must be fastened while
you operate the prime mover. Only operate the controls
while the engine is running. Protective glasses must be
worn while you operate the prime mover and while you
operate the sweeper.
•Replace any damaged or fatigued fittings or hoses.
• While you operate the sweeper slowly in an open area,
check for proper operation of all controls and all
protective devices. Note any needed repairs during
operation of the sweeper. Report any needed repairs.
8
SAFETY SECTION
GENERAL SAFETY INFORMATION
Service & Repair - General
CAUTION - Do not modify the sweeper in any way.
Personal injury could result. If you have
questions, contact your dealer or
SWEEPSTER.
WARNING!
Repair or adjust the sweeper in a safe area, away from
traffic and other hazards.
Before adjusting or servicing - lower the sweeper to the
ground, set parking brake, shut down the prime mover
and remove the key from the ignition.
When working on or around the sweeper, safely secure it
from falling or shifting.
WARNING!
Service & Repair - Hydraulic Safety
Stop the prime mover engine and release hydraulic pressure
before servicing or adjusting sweeper hydraulic systems.
WARNING - Escaping hydraulic fluid can have
enough pressure to penetrate the skin,
causing serious personal injury.
Check lines, tubes and hoses carefully. Do not use your
hand to check for leaks. Use a board or cardboard to check
for leaks. Tighten all connections to the recommended
torque. See Appendix.
Do not bend high pressure lines. Do not strike high pressure
lines, Do not install bent lines, bent tubes, or kinked hoses.
Do not install damaged lines, damaged tubes, or damaged
hoses.
Repair loose lines, loose tubes, and loose hoses. Repair
damaged lines, damaged tubes, and damaged hoses.
Leaks can cause fires. See your SWEEPSTER dealer for
repair or replacement parts.
Replace the parts if any of the following conditions are
present:
•The end fittings are damaged or leaking.
•The outer covering is chafed or cut.
•The reinforcing wire layer is exposed.
•The outer covering is ballooning locally.
•The hose is kinked or crushed.
•The hoses have been pulled or stretched.
Make sure that all clamps, guards, and shields are installed
correctly.
EXPOSURE TO RESPIRABLE
CRYSTALLINE SILICA DUST ALONG
WITH OTHER HAZARDOUS DUSTS
MAY CAUSE SERIOUS OR FATAL RESPIRATORY DISEASE.
It is recommended to use dust
suppression, dust collection and if
necessary personal protective equipment
during the operation of any attachment
that may cause high levels of dust.
REMOVE PAINT BEFORE WELDING
OR HEATING.
Hazardous fumes/dust can be generated
when paint is heated by welding,
soldering or using a torch. Do all work
outside or in a well ventilated area and
dispose of
paint and solvent properly. Remove paint
before welding or heating.
When sanding or grinding paint, avoid
breathing the dust. Wear an approved
respirator. If you use solvent or paint
stripper, remove stripper with soap and
water before welding. Remove solvent
or paint stripper containers and other
flammable material from area. Allow
fumes to disperse at least 15 minutes
before welding or heating.
9
Notes
10
SAFETY SECTION
SAFETY SIGNS & LABELS
Safety Signs and Labels
There are several specific safety signs on this sweeper.
The exact location of the hazards and the description of the
hazards are reviewed in this section.
Placement or Replacement of Safety Signs
Instructions
1. Clean the area of application with nonflammable solvent,
and then wash the same area with soap and water.
2. Allow the surface to fully dry.
3. Remove the backing from the safety sign, exposing the
adhesive surface.
4. Apply the safety sign to the position shown in the diagram
above and smooth out any bubbles.
•
•
•
Keep all safety signs clean and legible.
Replace all missing, illegible, or damaged safety signs.
Replacement parts, for parts with safety signs attached,
must also have safety signs attached.
• Safety signs are available, free of charge, from your dealer
or from SWEEPSTER.
10
8
10
13
14
8
7
Serial Number Tag
5
ItemPart
6.
7.
8.
9.
10.
11.
12.
13.
14.
50-0721
50-0722
50-0724
50-0725
50-0726
50-0769
50-0775
50-0779
41043
QtyDescription
2
1
1
2
2
1
2
4
1
Decal, Warning, Crush Hazard
Decal, Warning, Misuse Hazard
Decal, Warning, High Pressure Fluid Hazard
Decal, Warning, High Pressure Fluid Hazard
Decal, Warning, Flying Objects & Entanglement
Decal, Lift Point
Decal, Warning, Crush Hazard Vertical
Decal, Lift & Tie Down
Decal, Warning, Hazardous Dust
13
6
9
12
11
SAFETY SECTION
SAFETY SIGNS AND LABELS
Safety Signs and Labels
9. 50-0725
6. 50-0721
8. 50-0724
7. 50-0722
11. 50-0769
10. 50-0726
13. 50-0779
12. 50-0775
14. 41043
12
OPERATION SECTION
PRODUCT SPECIFICATIONS
C
Product Information
Section
A
A
B
H
H
D
F
F
G
G
B
B
D
D
C
EE
F
G
30°
30º
A
C
C
E
H
21319
21320
21321
A. Overall Height
143.7 inches (365 cm)
C. Overall Length @ 0º
21345
30°
167.7 inches (426 cm)
97.9 inches (249 cm)
A
D. Sweeping Width @ 0º
120 inches (304.8 cm)
E. Overall Length @ 30º
119.5 inches (303.5 cm)
F. Overall Width @ 30º
H. Center of Gravity
144 inches (365.8 cm)
125.5 inches (318.8 cm)
135.9 inches (345.2 cm)
156.7 inches (398 cm)
104 inches (264.2 cm)
129 inches (327.7 cm)
H
G. Sweeping Width @ 30º
48.7 inches
(123.7 cm)
Approx Weight
48.8 inches
(123.9 cm)
50 inches (127 cm)
2240 lbs (1016 kg)
50.1 inches
(127.3 cm)
2365 lbs (1073 kg)
Flow Range
12-30 gpm
(45-114 lpm)
18-45 gpm
(68-170 lpm)
Hydraulic Motor
Displacement
11.9 CI
11.9 / 23.9 CI 23.9 CI
Maximum Articulation
21344
53.2 inches (135.1 cm)
B. Overall Width @ 0º
Maximum Pressure
21343
24-60 gpm
(91 -227 lpm)
18-45 gpm
12-30 gpm
(45-114 lpm) (68-170 lpm)
11.9 CI
3000 psi ( 207 bar)
30 Degrees
24-60 gpm
(91 -227 lpm)
11.9 / 23.9 CI 23.9 CI
13
INSTALLATION SECTION
INSTALLING/REMOVING SWEEPER & STORAGE
Sweeper Installation
(Broom to Prime Mover)
Removing the Sweeper
WARNING - Serious injury or death may result from
disengaging the sweeper when the
sweeper is in an unstable position or
carrying a load. Place the sweeper in a
stable position before disengaging.
WARNING - Improper attachment of sweeper could
result in injury or death. Do not operate this
machine until you have positive indication
that the attachment is securely mounted.
1. Position the broom on a level surface.
2. Enter the prime mover.
3.
Fasten the safety restraints.
4.
Start the engine.
5.
Disengage the parking brake.
6. Align the attachment mechanism with the mounting on the
broom, attach to the prime mover. Follow the attaching
procedure in the prime mover owners manual.
7. Engage the parking brake and shut down the prime
mover. Be sure to relieve pressure to the auxiliary
hydraulic lines.
8. Unfasten safety restraints and exit the prime mover.
9. Lock jack stands in stowed position. (if available)
10. Ensure that the hydraulic quick couplers are clean.
Connect hydraulic lines for the broom to the
prime mover. Twist the collar of the quick couplers
one quarter of a turn in order to secure the hydraulic
connections.
11. While the loader arms are lowered, visually inspect the
attachment mechanism to ensure that it is securely
mounted.
12. Enter prime mover, fasten safety restraints and start the
prime mover.
13. Carefully raise the loader and cycle the rollback/dump
cylinders to check clearances, that limiting stops make
proper contact and verify that all mounting procedures
have been successfully completed. Contact SWEEPSTER
for instructions if the limiting stops do not contact properly.
NOTICE - Hoses for the sweepers must be removed before
the quick attach is disengaged. Pulling the
sweeper with the hoses could result in damage to
the prime mover or the sweeper.
1. Lower the broom to the ground.
2. Engage the parking brake and shut down the prime
mover. Be sure to relieve pressure to the auxiliary
hydraulic lines.
3. Unfasten safety restraints and exit prime mover.
4.Lock jack stands in lowered position. (if available)
5. Disconnect the broom hydraulic lines from the prime
mover. Connect quick couplers together to keep clean.
6. Disengage attachment locking mechanism.
(mechanical type)
7. Enter prime mover, fasten safety restraints and start the
prime mover.
8. Disengage attachment mechanism. (hydraulic type)
9. Disengage the parking brake, and back away from the
broom.
Storage
NOTICE -
Do not store the sweeper with weight on the
brush. Weight will deform the bristles,
destroying the sweeping effectiveness. To
avoid this problem, place the sweeper on
blocks or use storage stands.
Do not store polypropylene brushes in direct
sunlight. The material can deteriorate and
crumble before the bristles are worn out.
Keep polypropylene brush material away from
intense heat or flame.
14
Notes
15
Operation and
Maintenance Manual
Table of Contents
Operation..............................................................16-17
Operation .........................................................................16
Leveling Sweeper..............................................................17
Maintenance.........................................................18-22
Brush Pattern Adjustment..................................................18
Maintenance Schedule......................................................19
Maintenance Record..........................................................20
Replacing Brush Sections..................................................21
Lubrication Points............................................................. 22
16
OPERATION SECTION
SWEEPING/OPERATING TIPS
Before Each Use
Perform daily maintenance as indicated in Maintenance
Schedule.
Run the prime mover and sweeper at a slow idle. Check for
hydraulic leaks or other problems and make corrections, if
necessary, before using the sweeper. See “Hydraulic
inspection guideline” .
WARNING - Avoid serious injury. Check for large
objects that could harm the operator or
others if thrown by the sweeper. Remove
these items before operating.
During Use
Directing Debris
Carry the sweeper low to the ground so that the operator has
good visibility and stability. Avoid any sudden
movements.
Avoid excessive downward pressure on the brush
sections to prevent excessive wear. A two to four inch wide
pattern is sufficient for most applications. Ensure that the
adjustment bolts are equally adjusted in order to prevent an
uneven wear pattern. To adjust brush pattern see “Adjusting
Brush Pattern”.
Direct debris by angling the brush head in that direction.
Observe wind direction. Sweeping with the wind makes
sweeping more effective and helps keep debris off the
operator.
The terms swing and angle are used interchangeably.
Manual Angle
1. Remove the lock pin from links.
2. Position the brush head at the desired angle, aligning
holes in the inner and outer link.
3. Insert and close the lock pin.
Hydraulic Angle
1. Start the prime mover.
2. Position the brush head at the desired angle by using the
valve control for the swing function.
4. Engage the brush and then lower it to the ground.
5. Increase prime mover engine rpm to sweeping speed.
6. Travel forward at 5 mph (8 kph) or less.
NOTICE -
Avoid sweeper damage. Reduce travel speed to
avoid hitting immovable objects.
Operating Tips
NOTICE
- Avoid sweeper damage. Do not ram into piles.
Use an appropriate attachment for this type
of job.
Brush, Engine & Travel Speeds
Vary brush, engine and travel speeds to match sweeping
conditions.
Large Areas
When sweeping a large area, such as a parking lot, make a
path down the middle and sweep to both sides. This reduces the
amount of debris that the sweeper must sweep to one side.
Snow
Fast brush speeds and slow travel speeds are needed to sweep
snow effectively. Start at 3/4 throttle and the lowest gear of the
prime mover. For wet and/or deep snow, increase to almost full
throttle. This helps keep snow from packing up inside the brush
hood.
In deep snow you may need to make multiple passes to get
down to a clean surface.
To keep snow from blowing back onto a swept area, always
sweep so the wind is at your back.
Dirt & Gravel
To keep dust at a minimum, use the optional dust suppression
kit or plan sweeping for days when it is overcast and humid or
after it has rained. Also, sweep so the wind blows at your back.
Low brush speeds and moderate travel speeds work best for
cleaning debris from hard surfaces. Brush speeds that are too
fast tend to raise dust because of the aggressive sweeper
action.
Sweeping
To sweep gravel, use just enough brush speed to “roll” the
gravel, not throw it.
To sweep:
Heavy Debris
1. Manual angle only - Swing the brush head assembly
the direction that you want to direct debris.
Travel slowly - 2-3 mph. (3-5 kph)
2. Start the prime mover at idle and raise the brush.
3. Hydraulic angle only - Swing the brush head assembly
the direction that you want to direct debris.
Sweep a path less than the full width of the sweeper.
Increase engine speed if debris becomes very heavy.
17
OPERATION SECTION
LEVELING THE SWEEPER
Aligning Mounting
Align top edges of U-channels
10
The mounting incorporates a four-bar linkage system that
allows the sweeper to move up and down independently of the
loader arms. This feature is very important because it permits
the sweeper to follow the contours of the ground, offering a
good sweep.
8
10
NOTICE - Adjust the four-bar linkage before each
operation to avoid sweeper damage.
13
Sweeping with a properly
adjusted mounting offers13efficient performance, while using the mounting out of 14
adjustment can cause
8
6
severe damage to the sweeper and can result in a poor sweep.
7
9
If the U-channels on the loader arms are positioned too
low,
12 the
sweeper must support the loader arms,
an
amount
of
weight
far
5
greater than the sweeper is designed to carry. If the U-channels
on the loader arms are too high, the sweeper cannot sweep into
the low areas.
figure 1
To adjust the mounting:
1. Drive the loader and sweeper to a flat surface.
2. Lower the sweeper so the casters sit on the ground.
3. Adjust the loader arms so the tops of the U-channels on the
sweeper and the tops of the U-channels on the loader arms
are even (figure 1).
4. Adjust the brush height according to Setting Brush Pattern.
Leveling
Ground
Level the sweeper for even brush wear and effective use.
CAUTION - Avoid injury. Before adjusting the sweeper,
always turn off the sweeper and the prime
mover engine and remove the key.
figure 2
1. Move the sweeper to a flat, paved surface.
2. Lower the brush head assembly to the ground.
3. Position the brush head assembly straight ahead.
4. Engage the parking brake and shut down the prime mover.
Be sure to relieve pressure to the auxiliary hydraulic lines.
5. Unfasten safety restraints and exit prime mover.
6. On each side, measure from the brush frame to the ground
(figure 2). If measurements are not equal:
Loosen hardware that attaches the swing assembly to the
brush head assembly; lower the high side of the brush
head until both sides are an equal distance above the
ground. Tighten the hardware. (figure 3)
figure 3
18
MAINTENANCE SECTION
BRUSH PATTERN/SPRING CHAIN/TRANSPORT CHAIN
Setting Brush Pattern
A properly adjusted brush offers the best sweeper
performance. To check the brush pattern:
1. Move the sweeper to a dusty, flat surface.
2. Engage the parking brake and shut down the prime mover.
Be sure to relieve pressure to the auxiliary hydraulic lines.
3. Ratchet the brush head down until the bristles touch the
ground.
4. Start the sweeper at a slow speed. Run the sweeper in a
stationary position for 10 seconds.
5. Raise the sweeper and back away; switch off the engine
and remove the key. The brush pattern left in the dust
should be 2-4 inches (51-102 mm) wide, running the
length of the brush. (Compare the swept area with
figure 7.)
6. Adjust the brush pattern as necessary using the adjusting
ratchet.
Swept Area
2-4 in.
(51-102 mm)
Figure 7
19
MAINTENANCE SECTION
MAINTENANCE SCHEDULE
Maintenance Schedule
Procedure
Brush head assembly - Level
Brush pattern - Check (See Pattern Adj. Section)
Cylinders - Retract rods
- Grease threaded and ball ends to
prevent rust
Filter, air, prime mover - Clean
Fittings/hoses, hydraulic - Check for leaks/tighten
Check for damage
Fittings, zerk - Grease. (See lubrication points)
Oil, hydraulic - Check Level
Hardware - Check for tightness
Before
Each Use
After
Each Use
100
Hours
500
Hours
See Prime
Mover
20
MAINTENANCE SECTION
MAINTENANCE RECORDS
Maintenance Record
Use this log to record maintenance performed on the sweeper.
Date
Maintenance
Procedure Performed
Performed
By
Comments
21
MAINTENANCE SECTION
REPLACING BRUSH SECTIONS
1. Remove lynch pins and bushings. Retain
hardware for reinstallation. Remove motor.
2. Remove core from brush head assembly.
3. Remove lynch pins, bushings and motor from
the other side of brush head.
4. Remove idler bearing shaft mounting plate,
retaining hardware.
5. Remove second core from brush head
assembly.
6. Remove old sections.
figure 1
7. Install new sections by doing the following:
a. Slide the first section onto the core with the
drive pins on each side of a tube. Make sure
that the drive pins angle up. (figure 1)
b. Install a second section with drive pins
rotated 180° from those on the first section.
(figure 2)
c. Continue installing sections, rotating each
section 180° until the core is full.
figure 2
8. Re-attach the section retainer with previously
removed hardware.
9. Lay cores on ground. Lower frame over cores.
10.Re-attach idler bearing mounting plate with
previously removed hardware.
11.Re-attach motors with lynch pins and bushings.
Worn Section Standard
Section OD, Ring ID
New
24
26
32
36
36
46
6.38
8.00
10.00
10.00
10.63
19.38
Reference
Information
Section
OD, Worn
Exposed
Bristle, Worn
Bristle
Length
Exposed
Bristle, New
17
18
22
24
25
34
3.8
4.0
5.0
6.0
6.0
6.0
8.50
9.00
11.00
13.00
12.69
13.31
7.5
8.0
10.0
12.0
11.4
12.1
22
MAINTENANCE SECTION
LUBRICATION POINTS
Lubrication Points
The following grease fittings should be greased before each
use. See figure for locations.
1.
2.
3.
4.
Parallel Link Pins (8 fittings)
Caster Assembly (2 fittings)
Hydraulic Angle Cylinder (1 fitting)
Center Bearing, Between Cores (1 fitting)
4
3
1
1
2
23
Service Manual
Table of Contents
Troubleshooting .................................................23-33
Brush Head........................................................................24
Lift & Swing........................................................................25
Hydraulic System..........................................................26-29
Wiring Harness........................................................... 30--33
24
SERVICE SECTION
TROUBLESHOOTING
Brush Head
Problem
Possible Cause
Possible Solution
Brush rotates wrong direction
Hoses installed incorrectly
Switch hoses at brush head tubes
Brush slows or stops when sweeping
Brush pattern too wide
Adjust brush pattern to 2-4 inches
(51-101mm) wide: see Maintenance:
Adjusting Brush Pattern
Travel speed too fast
Travel no more than 5 mph (8 kph) while
sweeping (2-3 mph recommended)
Trying to sweep too much
material at once
Make several passes with sweeper
Relief pressure set too low
Set relief pressure to 2000 psi
(138.0 bars)
Filter plugging
Change or clean filter
Brush wears into cone shape
Tires on prime mover at
different pressures or are
different sizes
Check tire sizes and ratings: make
corrections as necessary
Brush wears very quickly
Brush pattern too wide
Adjust brush pattern to 2-4 inches
(51-101mm) wide: see Maintenance:
Setting Brush Pattern
25
SERVICE SECTION
TROUBLESHOOTING
Hydraulic Cylinders - Lift & Swing
Problem
Hydraulic cylinder neither extends
nor retracts
Hydraulic cylinder only extends or
only retracts
Possible Cause
Possible Solution
No power from controls because
wires are broken or disconnected
Reconnect wires if disconnected;
replace wires if broken
No power from controls because
switch is broken
Replace switch
Hoses or fittings loose or
disconnected
Tighten hoses or fittings
Restriction in hoses
Remove bends in hoses, remove
obstructions inside hoses
Dirt or debris in spools
Contact Sweepster Technical Service
26
SERVICE SECTION
TROUBLESHOOTING
Hydraulic System
Problem
Hydraulic system overheats
Hydraulic motor seals leak
Possible Cause
Possible Solution
Restriction in hoses
Remove bends in hoses; remove
obstructions inside hoses
Host pump flow rate exceeds
maximum rate of broom
Contact host manufacturer for proper
flow control method
Back pressure exceeds 1000psi
Contact Sweepster
Motor is failing
High number of hours on motor;
Contact dealer to rebuild or replace
Motor Port Identification
PRESSURE
RETURN
RETURN
PRESSURE
RETURN
PRESSURE
27
SERVICE SECTION
TROUBLESHOOTING
03-5215
12 Volt Manifold
A
Hydraulic Schematic
B
P
T
P
T
28
SERVICE SECTION
TROUBLESHOOTING
03-5835
12 Volt Manifold
Hydraulic Schematic
B
A
3
.082
2
P
1
10
T
P
HYDRAULIC SCHEMATIC
213 SERIES
T
29
SERVICE SECTION
TROUBLESHOOTING
03-5836
24 Volt Manifold
Hydraulic Schematic
B
A
3
.082
2
2
P
1
0
10
T
T
T
P
HYDRAULIC SCHEMATIC
213 SERIES
T
TO
WIRE HARNESS
M
TO
APPLICATION
APPLICATION
4 WIRE HARNESS
ROM
SS
H
G
F
E
A
B
C
D
E
B
C
D
A
F
H
G
TO
VIEW "A-A"
APPLICATION
LAF9444 WIRE
PLUGHARNESS
- A, D, E, G & H
IDENTIFICATION
FROM
PLUG - A, D, E, G & H
B
C
D
FROM
BATTERY
+
POSITIVE
BATTERY
NEGATIVE-
1.0
A
A
A
APPLICATION
TO
BATTERY
+
POSITIVE
TO
A
A
A
B
C
D
FROM
E
B
C
D
A
F
Description
Circuit Breaker
Switch
Rubber Boot
A
1.0
BATTERY
NEGATIVE-
BATTERY
+
POSITIVE
VIEW "A-A"
PLUG - A, D, E, G & H
H
G
Part
Qty
07-3152 1
07-0868 1
07-1824 1
TO
APPLICATION
LAF9444 WIRE HARNESS
IDENTIFICATION
F
E
H
G
Item
1.
2.
3.
A
A
1.0
BATTERY
NEGATIVE-
BATTERY
+
POSITIVE
VIEW "A-A"
PLUG - A, D, E, G & H
CONTROL OUT
C
B
TO
APPLICATION
CONTROL OUT
LAF9441 WIRE
HARNESSA
FROM
D
A
A,D,E,G,H PLUG
F
H
E
G
A,D,E,G,H PLUG
E
B
C
D
A
F
H
G
PLUG - A, D, E, G & H
C
B
A
A
1.0
BATTERY
NEGATIVE-
BATTERY
+
POSITIVE
VIEW "A-A"
CONTROL OUT
A,D,E,G,H PLUG
D
A
F
H
E
G
2
B
B
B
A
B
APPLICATION
A
H
1.0
1.0
BATTERY
NEGATIVE-
APPLICATION
CONTROL OUT
G
D
C
IDENTIFICATION
LAF9444
WIRE HARNESS
VIEW "A-A"
IDENTIFICATION
F
E
A
CONTROL OUT
H
G
PLUG - A, D, E, G & H
FROM
LAF9441
VIEW
"A-A" WIRE HARNESS
IDENTIFICATION
BATTERY
+
POSITIVE
F
BATTERY
A,D,E,G,H
PLUG
NEGATIVE-
E
A
A,D,E,G,H PLUG
LAF9441 WIRE HARNESS
IDENTIFICATION
A
APPLICATION
TO
B
APPLICATION
TO
Wiring Harness
A
FROM
441 WIRE HARNESS
SERVICE SECTION
TROUBLESHOOTING
41 WIRE HARNESS
ROM
30
1
3
2
1A
WIRE NO.
1A
1B
2
1A
0.38
PACKARD PIN B
BATTERY (-)
BLACK
12
-
PACKARD PIN A
0.38
SIZE
ULTRA SONIC SPLICE
TO
RED
12
APPLICATION
ULTRA SONIC SPLICE
FROM
BATTERY (+)
RED
GUAGE
12
IDENTIFICATION
WIRE
1B
NO
X
X
X
YES
-
EXTRA WIDE
PROTECTION
-
-
-
SIZE
1 WIRE TO BE TYPE GXL
RING TERMINAL (WAYTEK # 32205)
ULTRA SONIC SPLICE
RING TERMINAL (WAYTEK # 32205)
TYPE
TERMINAL
END (LEFT)
(BEYOND HARNESS)
PACKARD 12129493 & SEAL
PACKARD 12129493 & SEAL
ULTRA SONIC SPLICE
TYPE
TERMINAL
END (LEFT)
(BEYOND HARNESS)
-
-
-
YES
X
X
X
NO
EXTRA WIDE
PROTECTION
WIRE NO.
1A
1B
2
B
A
2
1B
31
SERVICE SECTION
TROUBLESHOOTING
Wiring Harness
32
SERVICE SECTION
TROUBLESHOOTING
1
2
3
4
WIRE NO.
16
16
16
16
GUAGE
1
2
WIRE
F
E
A
B
C
D
A
B
1
SIZE
-
3
4
TERMINAL
END (LEFT)
(BEYOND HARNESS)
EXTRA WIDE
PROTECTION
NO
YES
X
X
X
X
SIZE
0.25
0.25
0.25
EXTRA WIDE
PROTECTION
YES
NO
X
X
X
X
-
END (RIGHT)
(BEYOND HARNESS)
TERMINAL
TYPE
PACKARD 12048074 & SEAL
SPADE TERMINAL (FEMALE)
SPADE TERMINAL (FEMALE)
SPADE TERMINAL (FEMALE)
FLANGE W/ SLOT FOR
VELCRO MOUNTING STRAP
BRAID OVER WIRES
TYPE
PACKARD 12048159 & SEAL
PACKARD 12048159 & SEAL
PACKARD 12048074 & SEAL
PACKARD 12048074 & SEAL
2
VIEW B-B
B
A
C
WIRE TO BE TYPE GXL
TO
PACKARD PIN A (2-PIN)
SWITCH 1-A
SWITCH 1-B
SWITCH 1-C
APPLICATION
3
4
FROM
IDENTIFICATION
PACKARD PIN F (8-PIN)
PACKARD PIN B (2-PIN)
PACKARD PIN B (8-PIN)
PACKARD PIN C (8-PIN)
BLACK
RED
RED
YELLOW
1
H
PLUG - A,D,E,G, & H
VIEW A-A
G
POWER IN
CONTROL OUT
Wiring Harness
1
2
3
4
WIRE NO.
B
B
1
SWITCH
MOTION
2
DO NOT USE A NUT ON THE OUTSIDE OF
CONTROL BOX BETWEEN THE SWITCH
BOOT AND BOX.
VIEW A-A
RED
YELLOW
16
16
3
PACKARD 12045773 & SEAL
-
DEUTSCH 2 PIN A
PACKARD PIN C
A
1
WIRE TO BE TYPE GXL
1A
PACKARD 12045773 & SEAL
-
DEUTSCH 1 PIN A
PACKARD PIN B
BRAID OVER WIRES
ULTRA SONIC SPLICE
-
DEUTSCH 2 PIN B
ULTRA SONIC SPLICE
A
ULTRA SONIC SPLICE
-
PACKARD 12045773 & SEAL
DEUTSCH 1 PIN B
-
TYPE
TERMINAL
ULTRA SONIC SPLICE
ULTRA SONIC SPLICE
SIZE
1B
-
-
-
X
X
X
X
X
-
NO
1C
EXTRA WIDE
PROTECTION
YES
-
-
-
-
-
SIZE
DEUTSCH 0462-201-16141 & SEAL
DEUTSCH 0462-201-16141 & SEAL
DEUTSCH 0462-201-16141 & SEAL
DEUTSCH 0462-201-16141 & SEAL
ULTRA SONIC SPLICE
TYPE
TERMINAL
-
-
-
-
-
X
X
X
X
X
NO
EXTRA WIDE
PROTECTION
YES
A
PLUG A,D,E,G, & H
D
E
BLACK
16
2
BLACK
16
PACKARD PIN F
TO
APPLICATION
END (RIGHT)
(BEYOND HARNESS)
B
1A
B
C
F
A
H
BLACK
GAUGE
16
FROM
END (LEFT)
(BEYOND HARNESS)
A
G
WIRE NO.
1A
1B
1C
2
3
IDENTIFICATION
WIRE
WIRE NO.
1A
1B
1C
2
3
1C
3
1B
2
33
SERVICE SECTION
TROUBLESHOOTING
Wiring Harness
B
34
Notes
35
Parts Manual
Table of Contents
Parts Lists......................................................................35-45
Brush Head Frames...........................................................36
Core Assemblies................................................................37
Motor Assembly.................................................................38
Hydraulic Assembly...........................................................39
Manual Assembly...............................................................40
Swing Mountings..........................................................41-44
Brush Head Labels............................................................45
Brush Head Stand.............................................................46
36
PARTS SECTION
BRUSH HEAD FRAME
Brush Head Frame
2
12 19
3
11
3
18
4
16
9
7
1
17
14
15
10
4
13
22
7
2
8
5
6
NOTE:
1.
ASSEMBLE ITEM 20
WITH CROSS HOLES HORIZONTAL.
20
21
Item Part
QtyDescription
Item Part
Qty
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
1
30
50
8
8
8
8
8
1
1
1
12.
13.
14.
15.
16.
17.
18.
20.
21.
22.
2 Sheet, Hood, 5 Ft
2 Sheet, Hood, 6 Ft
1 Weld, Brush Frame, 10 Ft
1 Weld, Brush Frame, 12 Ft
2 Pin, 1 1/4 x 3.25, with Holes
1 Weld, Plate, Middle
2 Plate, Mounting, Middle
1 Plate, Mounting, Brush Head, Pivot
1 Sheet, Hood Filler
8 Pin, with Shoulder
12 Pin, Lynch, 1/4 4 Nut, Rivet, 5/16-18, .150-.312 Grip
07-2032
07-2952
07-3617
07-3760
07-4227
07-4228
07-4610
07-6026
13-11195
13-14077
13-14078
Clevis, Double Link, Gr80, 9/32
Screw, HFH, CL10.9, M6-1 x 20
Nut, Insert, Hex, M6 x 1
Screw, HHC, CL10.9, M12-1.75 x 40mm
Washer, Lock, Split, M14
Washer, Flat, CL8.8, M14
Nut, Hex, Lock, CL10.9, M12-1.75
Screw, HHC, CL10.9, M14-2 x 50 mm
Chain, 3/8, 26 Links
Sheet, Hood, Side, Left
Sheet, Hood, Side, Right
13-14817
13-14079
13-14550-10
13-14550-12
13-14787
13-14812
13-14814
13-14815
13-14816
13-16403
RHW8068
RHW8642
Description
37
PARTS SECTION
CORE ASSEMBLIES
Core Assemblies
2
9
14
10
13
3
DETAIL B
4
6
A
12 4
5
1
8
7
5
4
11
DETAIL A
B
01-1211-10 Set, Section, 36, Mixed, 10 ft
01-1211-12 Set, Section, 36, Mixed, 12 ft
01-1212-10 Set, Section, 36, Poly, 10 ft
01-1212-12 Set, Section, 36, Poly, 12 ft
Item Part
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Qty Description
07-3279
4
07-3617
8
07-3731
8
07-3747
28
07-3749
16
07-3752
12
07-6056
4
07-6866
1
13-12738
2
13-13166
2
13-14805
1
13-14808
1
13-15866-5 2
13-15866-6 2
13-16225
2
Washer, Flat, Gr8, 3/8
Nut, Insert, Hex, M6 x 1
Screw, HHC, CL10.9, M6-1 x 30mm
Washer, Lock, Split, Medium, M10
Screw, HHC, CL10.9, M10-1.5 x 30mm
Screw, HHC, CL10.9, M10-1.5 x 45mm
Nut, Flange, M10-1.5
Bearing, 1 1/2 Square, 4 Bolt
Plate, Hex, Hub, 5.25
Plate, Ring, Core, End
Weld, Square Shaft, 1 1/2, Core
Weld, Hub, Square, 1 1/2, with Doublers
Weld, Core, 10, 5 Ft
Weld, Core, 10, 6 Ft
Plate, Reciever, Hex, 2.5
38
PARTS SECTION
MOTOR ASSEMBLY
Motor Assembly













Hydraulic Motor Requirements
Model 21319 and 21343 Require 2 03-4430
Model 21321 and 21344 Require 1 03-4430 (Right) and 1 03-5192 (Left)
Model 21321 and 21345 Require 2 03-5192
ItemPart
1.
2.
3.
4.
5.
6.
7.
8.
QtyDescription
03-2035
2 Fitting, 12MF-16MB
See Above Chart
07-4227
4 Washer, Lock, Split, M14
07-7008
4 Screw, HHC, CL10.9, M14-2.0 x 55mm
07-7009
4 Nut, Hex, CL8.8, M14-2.0
13-15145 1 Plate, Mounting, Motor, Eaton
13-15149 4 Tube, Round, 1 1/2 x 1.06 x 4.25
13-15208 1 Hub, Hex, Drive
Replacement Parts for 03-4430 :
03-5043 Front, Seal Kit
03-5659 Rear, Seal Kit
03-5660 Complete, Seal Kit
Replacement Parts for 03-5192 :
03-5663 Front, Seal Kit
03-5664 Rear, Seal Kit
Must Order Both for Complete
39
PARTS SECTION
HYDRAULIC ASSEMBLY
Hydraulic Assembly
RETURN
TOP PORT ON MOTOR
15
PRESSURE
BTM PORT ON MOTOR
14
7
15
12
4
5
14
3
DETAIL A
2
13
1
8
30
25
CASE DRAIN
38
27
A
34
36
19
DIRECTION
OF FLOW
14
15
18
30
35
17
28
20
40
39
10
23
32
29
2
3
31
24
33
32
1.
2.
3.
4.
5.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
23.
24.
03-1945
03-2092
03-2291
03-3344
03-3779
03-4183
03-5160
03-5207
03-5212
03-5218
03-5235
03-5246
03-5236
03-5237
03-4119
03-5238
03-5248
03-5239
03-5241
03-5242
03-5243
03-5244
03-5494
03-4887
03-5724
PRESSURE
BTM PORT ON MOTOR
37
26
27
11
9
15
16
Replacement Parts for 03-5724:
45617 Seal Kit
104605 Cylinder Rod
Item Part
RETURN
TOP PORT ON MOTOR
14
Qty Description
1 Fitting, Adapter, HP, 1 1/16MOR, 3/4MFS
2 Fitting, Elbow, HP, 90°, 9/16MOR, 3/8MFS
2 Fitting, Adapter, HP, 3/8MFS, 9/16MOR
1 Fitting, Adapter, HP, 7/16MOR, 1/4MFS
1 Fitting, Adapter, HP, 1 1/16MOR, /4FFS
1 Fitting, Cross, 3/4MFS, All Ends
1 Tee, 12MF-12MF-12MF
4 Hose, Cradle
1 Fitting, Reducer, 12FFS, 4MFS
4 Cover, Plate
1 Hose, 1/4 x 84, TC, 4FFS, 4FFS45, 10ft
1 Hose, 1/4 x 96, TC, 4FFS, 4FFS45, 12ft
1 Hose, 3/8 x 42, TC, 6FFS, 6FFS90
2 Hose, 3/4 x 90, TC, 12FFS, 12FFS, 10ft
2 Hose, 3/4 x 102 TC, 12FFS, 12FFS, 12ft
2 Hose, 3/4 x 82, TC, 12FFS, 12FFS45, 10ft
2 Hose, 3/4 x 94, TC, 12FFS, 12FFS45, 12ft
1 Hose, 3/8 x 32, TC, 6FFS, 6FFS45
2 Hose, 1 x 120, TC, 16FFS, 12FFS90
1 Hose, Cradle
1 Cover, Plate
1 Weld, Plate
1 Fitting, 12FF, 12FF
1 Cylinder, 2.5 x 7.5 (09/23/09 & Before)
1 Cylinder, 2.5 x 1.38 x 7.5, 3.5K (9/24/09
& After)
25. 03-5215 1Manifold, Swing, 12 Volt (1018999 & Down)
03-5835 1 Manifold, Swing, 12 Volt (1019200 & Up)
03-5280 1 Manifold, Swing, 24 Volt (1018999 & Down)
03-5836
1 Manifold, Swing, 24 Volt (1019200 & Up)
Replacement Parts for 03-4887:
03-4888 Seal Kit
03-5035 Cylinder Rod
Item Part
Qty Description
07-7150
1
07-7151
1
07-7152
1
07-7153
2
07-7769
2
07-7134
2
07-7770
2
26. 07-0206
2
27. 07-3651
5
28. 07-3740
1
29. 07-3745
8
30. 07-3751
4
31. 07-4604
1
32. 07-4622
6
33. 07-7028
2
34. LAF9441 1
07-7737
1
35. LAF9444 1
36.
37.
38.
39.
40.
41.
07-7734
07-7733
105840
13-15085
13-15519
LAF4707
RHW8618
1
1
1
1
1
1
1
Valve, Cartridge, Press. Comp.
Valve, Cartridge, Relief
Valve, Cartridge, Directional
Coil, 12 Volt (1018999 & Down)
Coil, 12 Volt (1019200 & Up)
Replacement Nut - 07-7771
Coil, 24 Volt (1018999 & Down)
Coil, 24 Volt (1019200 & Up)
Replacement Nut - 07-7771
Pin, Cotter, Gr2, 3/16 x 2
Screw, HHC, Gr8, 5/16-18 x 3
Screw, HHC, CL10.9, M8-1.25 x 30mm
Washer, Flat, CL8.8, M10
Screw, HHC, CL10.9, M10-1.5 x 40mm
Nut, Hex, Lock, M8-1.25, CL10.9
Nut, Hex, Lock, ST, CL10.9, M10-1.5
Screw, HHC, CL10.9, M10-1.5 x 130mm
Wire Assembly, 9 Ft (1018999 & Down)
Wire Harness, 9 Ft (1019200 & Up)
Wire, Harness, with Box (1018999 &
Down)
Wire Harness, with Box (1019200 & Up)
Wire, Harness, Power Lead, 126 inches
Washer, Fender
Plate, Mounting
Plate, Mounting, Bulkhead
Valve, Check, In-Line, 12MF, 12MF
Hose Spring
40
PARTS SECTION
MANUAL ASSEMBLY
Manual Assembly
RETURN
TOP PORT
ON MOTOR
PRESSURE
BOTTOM PORT
ON MOTOR
5
11
2
21
1
6
RETURN
TOP PORT
ON MOTOR
7
RETURN
PRESSURE
BOTTOM PORT
ON MOTOR
17
PRESSURE
16
14
9
19
8
10
15
20
24
18
23
22
13
12
ItemPart
1.
2.
3.
4.
5.
7.
8.
9.
10.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
03-5238
03-4119
03-5160
03-5207
03-5218
03-5237
03-5248
03-5241
03-5242
03-5243
03-5244
07-0206
07-2105
07-3651
07-3740
07-3745
07-3751
07-4604
07-4622
105840
13-15519
13-2452
13-2453
RHW8618
QtyDescription
2
2
2
4
4
2
2
2
1
1
1
2
1
5
1
2
2
1
2
2
1
1
1
1
Hose, .75 x 82, 12FF-12FF45, 3K, TC (10 Ft)
Hose, .75 x 102, 12FF-12FF, 3K, TC (12 Ft)
Tee, 12MF-12MF-12MF, Bulkhead, R
Hose, Cradle, for 1.12 OD
Cover, Plate, for 1.12 OD
Hose, .75 x 90, 12FF-12FF, 3K,TC (10 Ft)
Hose, .75 x 94, 12FF-12FF45, 3K, TC (12 Ft)
Hose, 1 x 120, 12FF90-16FF, 3K, TC
Hose, Cradle, for 1.40 OD
Cover, Plate, for 1.40 OD
Weld, Plate, for 1.40 OD
Pin, Cotter, Gr2, 3/16 x 2
Pin, Lock, 3/8 Square Bail
Screw, HHC, Gr5, 5/16-18 x 3
Screw, HHC, CL10.9, M8-1.25 x 30mm
Washer, Flat, CL8.8, M10
Screw, HHC, CL10.9, M10-1.5 x 40mm
Nut, Hex, Lock, CL10.9, M8-1.25
Nut, Hex, Lock, CL10.9, M10-1.5
Washer, Fender
Plate, Mounting, Bulkhead
Weld, Link, Inner
Weld, Link, Outer
Hose, Spring
14
4
3
41
PARTS SECTION
SWING MOUNTING
Bolt-On Swing Mounting
4
30
29
14
29
2
27
9
32
15
17
12
10
16
19
31
22
8
26
3
23
6
24
28
1
16
17
7
25
21
18
11
20
Item
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
Part
07-0119
07-0206
07-0223
07-0786
07-1294
07-1762
07-1763
07-1764
07-1817
07-1841
07-1872
07-2104
07-2360
07-2484
07-3064
07-3065
Qty Description
3
2
8
2
3
8
4
8
6
8
3
1
4
1
8
9
Bolt, Carriage, Gr5, 5/8-11 x 1 3/4
Pin, Cotter, Gr2, 3/16 x 2
Fitting, Zerk, 1/8NPT
Pin, Cotter, Gr2, 3/16 x 1 1/2
Nut, Hex, Gr8, 5/8-11
Washer, Lock, Split, Medium, 1/2
Washer, Flat, Gr8, 1/2
Nut, Hex, Gr8, 1/2-13
Tie, Plastic, 15 inch
Washer, Flat, Gr2, 1 1/8
Washer, Lock, Split, Medium, 5/8
Toplink, Ratchet, 8 Stroke
Screw, HHC, Gr8, 1/2-13 x 4
Toplink, CAT 0, 10 3/4C x 16 3/8E
Screw, HHC, Gr8, 3/4-10 x 2
Washer, Lock, Split, Medium, 3/4
5
13
Item
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
Part
Qty Description
07-3066 9 Nut, Hex, Gr8, 3/4-10
07-3120 3 Washer, Flat, Gr8, 5/8
07-3544 1 Screw, HHC, Tap, Gr5, 3/4-10 x 3
07-3256 2Assembly, Caster, 6 Ply, Taper Bearing
07-3941 2Assembly, Caster, Solid Taper Bearing
07-5075 4 Screw, HHC, Gr8, 1/2-13 x 2
07-5355 8 Pin, Cotter, 5/16 x 2
12-0292 8 Pin, Hitch, 1.122 x 4
12-4152 4 Weld, Link, Hitch, 6.25
13-2218 1 Weld, Plate, Swing
13-2230 1 Bushing, 1 3/4 x 25/32 x 1 1/16
13-2484 1 Pin, 1 x 4, with Holes
13-3134 1 Weld, Frame, Swing
13-3413 2 Weld, Pin, Mounting, 5/8 x 3 1/2
13-4386 1 Weld, Bracket, Lift
13-4387 1 Tube, Lift
50-0635 1 Label, Part Number, Date
42
PARTS SECTION
SWING MOUNTING
Weld-On Swing Mounting
4
28
28
14
2
26
29
10
9
12
21
8
18
6
25
3
22
23
15
27
16
1
8
6
7
24
17
11
5
20
13
19
Item
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Part
07-0119
07-0206
07-0223
07-0786
07-1294
07-1762
07-1763
07-1764
07-1817
07-1841
07-1872
07-2104
07-2360
07-2484
07-3065
Qty Description
Item
3
2
8
2
3
8
4
8
6
8
3
1
4
1
1
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
Bolt, Carriage, Gr5, 5/8-11 x 1 3/4
Pin, Cotter, Gr2, 3/16 x 2
Fitting, Zerk, 1/8NPT
Pin, Cotter, Gr2, 3/16 x 1 1/2
Nut, Hex, Gr8, 5/8-11
Washer, Lock, Split, Medium, 1/2
Washer, Flat, Gr8, 1/2
Nut, Hex, Gr8, 1/2-13
Tie, Plastic, 15 inch
Washer, Flat, Gr2, 1 1/8
Washer, Lock, Split, Medium, 5/8
Toplink, Ratchet, 8 Stroke
Screw, HHC, Gr8, 1/2-13 x 4
Toplink, CAT 0, 10 3/4C x 16 3/8E
Washer, Lock, Split, Medium, 3/4
Part
Qty Description
07-3066 1 Nut, Hex, Gr8, 3/4-10
07-3120 3 Washer, Flat, Gr8, 5/8
07-3544 1 Screw, HHC, Tap, Gr5, 3/4-10 x 3
07-3256 2Assembly, Caster, 6 Ply, Taper Bearing
07-3941 2Assembly, Caster, Solid, Taper Bearing
07-5075 4 Screw, HHC, Gr8, 1/2-13 x 2
07-5355 8 Pin, Cotter, 5/16 x 2
12-0292 8 Pin, Hitch, 1.122 x 4
12-4152 4 Weld, Link, Hitch, 6.25
13-2218 1 Weld, Plate, Swing
13-2230 1 Bushing, 1 3/4 x 25/32 x 1 1/16
13-2484 1 Pin, 1 x 4, with Holes
13-3134 1 Weld, Frame, Swing
13-3413 2 Weld, Pin, Mounting, 5/8 x 3 1/2
50-0635 1 Label, Part Number, Date
43
PARTS SECTION
SWING MOUNTING
Swing Mounting 3 Point Category II
Serial # 0943100 and Lower
ItemPart
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
07-0119
07-0206
07-0244
07-0688
07-1294
07-1762
07-1763
07-1764
07-1872
07-2104
07-2360
07-3065
QtyDescription
3
2
2
2
3
8
4
8
3
1
4
1
Bolt, Carriage, Gr5, 5/8-11 x 1 3/4
Pin, Cotter, Gr2, 3/16 x 2
Pin, Linch, 1/4
Pin, Hitch, CAT II, 7/8 Thread
Nut, Hex, Gr8, 5/8-11
Washer, Lock, Split, Medium, 1/2
Washer, Flat, Gr8, 1/2
Nut, Hex, Gr8, 1/2-13
Washer, Lock, Split, Medium, 5/8
Toplink, Ratchet, 1 inch Pins
Screw, HHC, Gr8, 1/2-13 x 4
Washer, Lock, Split, Medium, 3/4
ItemPart
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
07-3066
07-3120
07-3544
07-3941
07-5075
13-11997
13-2218
13-2230
13-2484
13-7265
50-0635
QtyDescription
1
3
1
2
4
1
1
1
1
1
1
Nut, Hex, Gr8, 3/4-10
Washer, Flat, Gr8, 5/8
Screw, HHC, Gr8, 3/4-10 x 3
Caster, Assembly, Swivel
Screw, HHC, Gr8, 1/2-13 x 2
Pin, .875 x 6.5
Weld, Plate, Swing
Bushing, 1 3/4 x 25/32 x 1 1/16
Pin, 1 x 4, with Holes
Weld, Frame
Label, Part Number, Date
44
PARTS SECTION
SWING MOUNTING
Swing Mounting 3 Point Category II
Serial # 0943101 and Higher
8
2
19
17
6
4
5
20
25
13
18
23
9
10
15
11
14
16
24
21
ItemPart
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
07-0119
07-0206
07-1294
07-1762
07-1763
07-1764
07-1872
07-2104
07-2360
07-3065
07-3066
07-3120
07-3544
22
26
QtyDescription
3
2
3
8
4
8
3
1
4
1
1
3
1
Bolt, Carriage, Gr5, 5/8-11 x 1 3/4
Pin, Cotter, Gr2, 3/16 x 2
Nut, Hex, Gr8, 5/8-11
Washer, Lock, Split, Medium, 1/2
Washer, Flat, Gr8, 1/2
Nut, Hex, Gr8, 1/2-13
Washer, Lock, Split, Medium, 5/8
Toplink, Ratchet, 1 inch Pins
Screw, HHC, Gr8, 1/2-13 x 4
Washer, Lock, Split, Medium, 3/4
Nut, Hex, Gr8, 3/4-10
Washer, Flat, Gr8, 5/8
Screw, HHC, Gr8, 3/4-10 x 3
ItemPart
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
07-3941
07-5075
13-17196
13-2218
13-2230
13-2484
50-0635
LAF9429
LAF9430
LAF9433
P121200
P126250
RHW8130
QtyDescription
2
4
1
1
1
1
1
2
2
1
1
1
4
Caster, Assembly, Swivel
Screw, HHC, Gr8, 1/2-13 x 2
Weld, Frame, 3 Point
Weld, Plate, Swing
Bushing, 1 3/4 x 25/32 x 1 1/16
Pin, 1 x 4, with Holes
Label, Part Number, Date
Tube, Round, 1.13 x .885 x 5.56
Rod, 1 x 3.62, with Chamfers
Bushing, Toplink, Category 2-3
Pin, Hitch
Bushing, Category l-ll
Rue Ring, Cotter, .88, Heavy
45
PARTS SECTION
BRUSH HEAD LABELS
Brush Head Labels
4
12
11
10
6
11
7
12
5
8
13
ItemPart
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
41043
50-0185
50-0252
50-0634
50-0643
50-0721
50-0722
50-0724
50-0726
50-0775
9
QtyDescription
1
2
1
1
2
2
1
1
2
2
Decal, Warning, Hazardous Dust
Label, Logo, Medium, White
Label, Logo, Large, White
Label, Serial Number, Sweepster
Label, Tie Down Point
Label, Warning, Crush Hazard
Label, Warning, Misuse Hazard
Label, Warning, High Pressure Fluid Hazard
Label, Warning, Flying Objects & Entanglement
Label, Warning, Crush Hazard
46
PARTS SECTION
BRUSH HEAD STAND
Brush Head Stand
1
2
4
ItemPart
1.
2.
3.
4.
07-0260
07-0699
07-4748
13-13898
QtyDescription
2
2
2
2
Pin, Clevis, Gr2, 3/8 x 2 3/4
Pin, Cotter, Gr2, 1/8 x 1 1/4
Pin, Lock, 3/8 x 2
Weld, Stand
3
47
Options Section
Table of Contents
Options.................................................................47-55
Hood Kits............................................................48-49
Dust Suppression..................................................... 50
Water Tank..........................................................51-52
Sight Indicator Kits................................................... 53
Case Drain Kit.......................................................... 54
Hydraulic Angle........................................................ 55
48
OPTION SECTION
HOOD KITS
180° Hood with Drape
28-9927-10 10 Ft
28-9927-12 12 Ft
1
13
10
16
4
2
3
5
17
7
18
8
1
6
3
1
2
11
12
ItemPart
QtyDescription
1.
2.
3.
4.
5.
6.
7.
8.
10.
11.
12.
13.
16.
17.
18.
36
20
20
10
10
10
2
2
2
2
2
2
1
1
1
1
1
1
07-2952
07-3617
07-3736
07-3737
07-3738
07-3739
07-3761
07-4610
13-12834
13-12298
13-14575
13-14536
13-14545
13-14546
13-14577
13-14578
13-15325
13-15326
Screw, HFH, CL10.9, M6-1 x 20
Nut, Insert, Hex, M6 x 1
Washer, Flat, CL8.8, M8
Nut, Hex, CL10, M8-1.25
Washer, Lock, Split, Medium, M8
Screw, HHC, CL10.9, M8-1.25 x 25mm
Screw, HHC, CL10.9, M12-1.75 x 45mm
Nut, Hex, Lock, CL10.9, M12-1.75
Plate, Retainer, 5 ft, Dirt Deflector (10 Ft)
Plate, Retainer, 6 ft, Dirt Deflector (12 Ft)
Sheet, Hood, 5 ft 180° (10 Ft)
Sheet, Hood, 6 ft 180° (12 Ft)
Sheet, Side, Left, Hood
Sheet, Side, Right, Hood
Flap, Hood, 180° (10 Ft)
Flap, Hood, 180° (12 Ft)
Sheet, 180° Hood Filler
Weld, Support
49
OPTION SECTION
HOOD KITS
180° Hood
28-9932-10 10 Ft
28-9932-12 12 Ft
4
3
10
9
6
5
2
1
1
7
2
ItemPart
QtyDescription
1.
2.
3.
4.
5.
6.
7.
9.
10.
36
20
2
2
2
2
1
1
1
1
07-2952
07-3617
07-3761
07-4610
13-14575
13-14536
13-14545
13-14546
13-15325
13-15326
1
Screw, HFH, CL10.9, M6-1 x 20
Nut, Insert, Hex, M6 x 1
Screw, HHC, CL10.9, M12-1.75 x 45mm
Nut, Hex, Lock, CL10.9, M12-1.75
Sheet, Hood, 5 ft, 180° (10 Ft)
Sheet, Hood, 6 ft, 180° (12 Ft)
Sheet, Side, Left
Sheet Side, Right
Sheet, 180° Hood Filler
Weld, Support, Hood
50
15
OPTIONS SECTION
DUST SUPPRESSION
16
12
6
5
DETAIL C
9
Dust Suppression
1
3
19
16
DETAIL B
Kit: 28-9928
7
17
10
4
22
17
DETAIL A
12
6
5
20
11
8
15
2
21
23
DETAIL C
18
9
C
19
1
A
2
3 21
25
20
14
10
11
B
24
22
13
26
23
18
15
C
16
12
6
5
DETAIL C
9
19
16
DETAIL B
B
7
17
11
8
4
NOTE 1: MOUNT1SPRINKLER
14 3 KIT
IN THIS POSITION WHEN
21
USING 180 DEGREE
HOOD AND DEFLECTOR
OPTIONS.
13
2
20
10
Replacement Parts for 03-1326 :
07-6565 Fan Shroud
07-6566 Grommet Set (Qty 4)
07-6567 Motor Base Plate
22
17
DETAIL A
23
18
Replacement Parts for LAF8316 :
07-7492 Switch
07-3152 Circuit Breaker
07-1824 Rubber Boot
C
A
Item Part
Qty
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
1
1
1
1
4
4
4
4
4
1
1
10
8
1
1
4
03-0457
03-1226
03-1326
03-2558
03-3537
07-0140
07-0141
07-0413
07-0414
07-0532
07-0547
07-0549
07-1430
07-3869
07-4804
07-4831
Description
Barb, 6, 6MP
Barb, 10, 8MP
Pump, Flojet, Water, 2.1gpm, 12 volt
Pump, Flojet, Water, 2.1gpm, 24 volt
O-Ring, #8, Face Seal
Washer, Lock, Gr2, #10
Nut, Hex, Gr2, 10-24
Nozzle, Cap, Nylon
Nozzle, Tip, Brass
Strainer, Hypro, Water
Clamp, Spring, 7/8, Hose
Clamp, Spring, 5/8, Hose
Washer, Flat, #10
Fitting, Barb, Tee, Nylon, 3/8
Grommet, Rubber, 1-1/4 x 7/8 x 1/16
Screw, BHC, 10-24UNC, 2B x 3/4
Item Part
Qty
Description
07-4861
2 14Nozzle, Tee, without Clamp
07-4862
2 Nozzle, Elbow, without Clamp
07-5127 25ft Hose, Clear, Vinyl, 3/8 (To make # 24,
25, 26)
13 1 Valve, Shut-off, 1/2
19. 07-6862
20. 07-6863
1 Fitting, Nipple, 1/2
21. 07-6864
1 Fitting, Nipple, 1/2 x 3/8
22. LAF8316 1 Wire Harness, with Box
23. LAF8320 1 Wire Harness, 11 Ft
24. 07-5127 33 in. Hose, Clear, Vinyl, 3/8, 10 Ft
07-5127 39 in. Hose, Clear, Vinyl, 3/8, 12 Ft
25. 07-5127 31 in. Hose, Clear, Vinyl, 3/8, 10 Ft
07-5127 37 in. Hose, Clear, Vinyl, 3/8, 12 Ft
26. 07-5127 32 in. Hose, Clear, Vinyl, 3/8, 10 Ft
07-5127 38 in. Hose, Clear, Vinyl, 3/8, 12 Ft
16.
17.
B
18.
51
OPTIONS SECTION
WATER TANK
85 Gallon Water Tank
Kit: 28-4318
12
11
2
15
1
10
5
14
8
7
6
13
9
3
4
A
13
DETAIL A
18
17
16
Item Part
Qty
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
1
1
1
1
1
6
6
1
4
4
1
2
03-0714
03-1068-9
07-1716
07-1734
03-3279
03-3433
07-4031
07-4036
07-4037
07-4262
07-4682
09-0202
Description
Barb, 10, 8MP90
Fitting, 8FP-12MP
Bolt, Carriage, Gr5, 3/8-16 x 1
Clamp, Rubber Coat, 1 inch
Washer, Flat, Gr8, 3/8
Screw, HHC, Gr8, 5/8-11 x 1 1/2
Nut, Hex, Nylock, Gr8, 5/8-11
Nut, Hex, Nylock, Gr8, 3/8-16
Nut, Hex, Nylock, Gr8, 1/2-13
Bolt, Lag, 5/16 x 1 1/2
Tank, Water, Poly, 85 gallons
Strap, Nylon, 37 inches
Item Part
Qty
13.
14.
15.
16.
17.
18.
1
2
4
1
1
1
13-10074
13-10075
13-10081
13-10485
13-15523
13-15524
Description
Weld, Mounting, Water Tank
Rubber, Neoprene, Tank, Pad
Weld, Bolt, Tee, 3 1/2
Handle, Ratchet
Weld, Mounting, Tank, Left
Weld, Mounting, Tank, Right
Replacement Parts for 07-4682 :
07-6088 Cap
07-7168 Drain Assembly
52
OPTIONS SECTION
WATER TANK
85 Gallon Water Tank 3 Point
Kit: 28-10217
11
13
10
12
16
2
3
8
1
5
4
15
17
6
9
7
14
Item Part
Qty
1.
2.
3.
4.
5.
6.
7.
8.
1
1
1
4
16
8
4
1
07-1716
07-1734
07-3279
07-3638
07-3671
07-4032
07-4033
07-4036
Description
Bolt, Carriage, Gr5, 3/8-16 x 1
Clamp, Rubber, Vinyl, Coat, Hose, 1
Washer, Flat, Gr8, 3/8
Screw, HHC, Gr8, 1/4-20 x 1 1/4
Screw, HHC, Gr8, 1/2-13 x 1 3/4
Washer, Flat, Gr8, 1/4
Nut, Hex, Nylock, Gr8, 1/4-20
Nut, Hex, Nylock, Gr8, 3/8-16
Item Part
Qty
9.
10.
11.
12.
13.
14.
15.
16.
17.
20
1
2
2
4
1
2
1
1
07-4037
07-4682
09-0202
13-10075
13-10081
13-10485
13-16545
13-16548
13-16549
Replacement Parts for 07-4682 :
07-6088 Cap
07-7168 Drain Assembly
Description
Nut, Hex, Nylock, Gr8, 1/2-13
Tank, Water, Poly, 85 Gallon, 32 Inch
Strap, Water, Tank, 34 Inch
Rubber, Neoprene, Tank Pad
Weld, Bolt, Tee, 3 1/2
Handle, Ratchet
Plate, Tank, Mounting, Water, 3 Point
Weld, Mounting, Tank, Water
Plate, Mounting, Water Pump
53
OPTIONS SECTION
SIGHT INDICATOR KITS
Sight Indicators
Kit: 28-9965
2
1
Item Part
QtyDescription
5
1.
2.
3.
4.
5.
07-3279
07-5839
07-6597
13-14857
13-9567
2
2
4
2
2
Washer, Flat, Gr8, 3/8
Nut, Hex, Nylock, 3/8-24
Screw, HFH, CL10.9, M6-1 x 30
Weld, Sight Indicator
Ball, 2 1/8, Red, with Hole
4
3
Kit: 11-5897
54
OPTIONS SECTION
CASE DRAIN
Case Drain Assembly
12
34
53
45
REUSED FROM LEFT SIDE
OF STANDARD HYDRAULIC
ANGLE PACKAGE.
Item Part
1.
2.
3.
4.
5.
03-3135
03-3344
03-5245
03-5247
03-5249
QtyDescription
1
1
1
1
1
Tee, 12MB-12MF-12MF
Fitting, 4MB-4MF
Hose, .25 x 104, 4FF-4FF45, 3K, AR
Hose, .25 x 120, 4FF-4FF90, 3K, AR
Tee, 4MF-4MF-4MF, BHD, R
21
55
OPTIONS SECTION
HYDRAULIC ANGLE
HYDRAULIC ANGLE ASSEMBLY
Item Part
QtyDescription
1. 03-20922 Elbow, 90º, 6MB-6MF
2. 03-21552 Hose, .25 x 72, 6FF-6FF, 3.25K
3.03-2159
2
Fitting, 6MF-4MP
4. 03-57241 Cylinder, 2.5 x 1.25, 3.5K (09/24/09 and Up)
03-48871 Cylinder, 2.5 x 1.38 x 7.5, 3.5K (09/23/09 and Down)
6. 07-02062 Pin, Cotter, Gr2, 3/16 x 2
Replacement Parts for 03-5724 :
45617 Seal Kit
Replacement Parts for 03-4887 :
03-4888 Seal Kit
03-5035 Rod
HYDRAULIC ANGLE CYLINDER
2
1
Item Part
1.
2.
QtyDescription
03-57241 Cylinder, 2.5 x 1.25, 3.5K (09/24/09 and Up)
03-48871 Cylinder, 2.5 x 1.38 x 7.5, 3.5K (09/23/09 and Down)
07-02062 Pin, Cotter, Gr2, 3/16 x 2
56
Notes
57
Appendix
Table of Contents
Bolt Torque Specifications........................................ 58
Hydraulic Fittings Torque Specifications.............59-60
Warranty Information................................................ 61
58
APPENDIX
TORQUE SPECS.
Foot-pounds may be converted to Newton Meters by multiplying by 1.35582
Foot-pounds may be converted to Inch-pounds by multiplying by 12.
If the nut and screw are not the same grade, the lower grade will always be used.
NOTE - Nylock nuts are utilized when greater resistance to vibrating loose is required, and greater operating temperatures are
not a factor. In addition, like lock nuts, nylock nuts have a safety feature that if the bolt does vibrate loose, the nut will
remain on the screw. Install nylock nuts to the standard torque shown above.
59
APPENDIX
TORQUE SPECS
Hydraulic Torque Specifications
Face Seal: Assembly, Tube to Fitting
Note - Face seal fittings have the most reliable sealing method and therefore, should be used
whenever possible.
Installation
1. Make sure threads and sealing surfaces are free of burrs, nicks, scratches, or any foreign materials.
2. Install proper SAE o-ring to end of fitting if not already installed. Ensure o-ring is fully seated and retained properly.
3. Lubricate o-ring with a light coating of clean hydraulic oil.
4. Position tube and nut squarely on face seal of fitting and tighten nut finger tight.
5. Using appropriate torquing device, tighten to given torque rating from the table below.
Torque Values:
SAE Dash Size
-4
Tube Side
Thread Size
9/16 - 18
In-lbs
Ft-lbs
220 ± 10
18 ± 1
-6
11/16 - 16
320 ± 25
27 ± 2
-8
13/16 - 16
480 ± 25
40 ± 2
-10
1- 14
750 ± 35
63 ± 3
-12
1 3/16 - 12
1080 ± 45
90 ± 4
-16
1 7/16 - 12
1440 ± 90
120 ± 8
-20
1 11/6 - 12
1680 ± 90
140 ± 8
-24
2 - 12
1980 ± 100
165 ± 8
NOTE - ft-lb may be converted to Newton Meters by multiplying by 1.35582.
NOTE - in-lbs may be converted to Newton Meters by multiplying by 0.11298.
60
APPENDIX
TORQUE SPECS.
Hydraulic Torque Specifications
Straight Thread O-ring Fitting: Assembly, Fitting to Port
NOTE - Straight thread o-ring fittings are utilized to adapt hydraulic systems to
motors, pumps, cylinders, and valves.
Installation (Adjustable Fitting)
1. Make sure threads and sealing surfaces are free of burrs, nicks, scratches, or any foreign materials.
2. Install proper SAE o-ring on port end of fitting if not already installed. Ensure o-ring is fully seated and retained properly.
3. Lubricate o-ring with a light coating of clean hydraulic oil.
4. Back off nut as far as possible and push washer up as far as possible. (Figure 4 & 5)
5. Screw fitting into port. Hand tighten fitting until backup washer contacts face of port. (Figure 6)
6. To position the fitting, unscrew to desired position, but not more than one full turn.
7. Hold fitting in position with wrench. Using appropriate torquing device, tighten nut to given torque rating from the table in
section. (Figure 7)
Torque Values
Figures 4, 5, 6 and 7
Fitting
Size
SAE Port
Thread Size
-4
7/16 - 20
190 ± 10
16 ± 1
-6
9/16 - 18
420 ± 15
35 ± 1
-8
3/4 - 14
720 ± 25
60 ± 2
-10
7/8 - 14
1260 ± 50
105 ± 5
-12
1 1/16 - 12
1680 ± 75
140 ± 6
-16
1 5/16 - 12
2520 ± 100
210 ± 8
-20
1 5/8 - 12
3100 ± 150
260 ± 12
-24
1 7/8 - 12
3800 ± 150
315 ± 12
In-Lbs
Ft-Lbs
NOTE - ft-lb may be converted to NewMeters by multiplying by 1.35582.
NOTE - in-lbs may be converted to Newton Meters by multiplying by 0.11298.
61
APPENDIX
WARRANTY INFORMATION
Limited Warranty
Except for the Excluded Products as described below, all new products are warranted to be free from defects
in material and/or workmanship during the Warranty Period, in accordance with and subject to the terms and
conditions of this Limited Warranty.
1.
Excluded Products. The following products are excluded from this Limited Warranty:
(a) Any cable, part that engages with the ground (i.e. sprockets), digging chain, bearing, teeth, tamping
and/or demolition head, blade cutting edge, pilot bit, auger teeth and broom brush that either constitutes or is part
of a product.
(b) Any product, merchandise or component that, in the opinion of Paladin Light Construction1, has been
(i) misused; (ii) modified in any unauthorized manner; (iii) altered; (iv) damaged; (v) involved in an accident; or (vi)
repaired using parts not obtained through Paladin Light Construction.
2.
Warranty Period. The Limited Warranty is provided only to those defects that occur during the Warranty
Period, which is the period that begins on the first to occur of: (i) the date of initial purchase by an end-user, (ii) the
date the product is first leased or rented, or (iii) the date that is six (6) months after the date of shipment by Paladin
Light Construction as evidenced by the invoiced shipment date (the “Commencement Date”) and ends on the date
that is twelve (12) months after the Commencement Date.
3.
Terms and Conditions of Limited Warranty. The following terms and conditions apply to the Limited Warranty
hereby provided:
(a)
the product.
Option to Repair or Replace. Paladin Light Construction shall have the option to repair or replace
(b)
Timely Repair and Notice. In order to obtain the Limited Warranty, (i) the product must be repaired
within thirty (30) days from the date of failure, and (ii) a claim under the warranty must be submitted to Paladin Light
Construction in writing within thirty (30) days from the date of repair.
(c)
Return of Defective Part or Product. If requested by Paladin Light Construction, the alleged
defective part or product shall be shipped to Paladin Light Construction at its manufacturing facility or other location
specified by Paladin Light Construction, with freight PRE-PAID by the claimant, to allow Paladin Light Construction
to inspect the part or product.
Claims that fail to comply with any of the above terms and conditions shall be denied.
LIMITATIONS AND EXCLUSIONS.
THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WITHOUT LIMITATION THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
AND ANY WARRANTY BASED ON A COURSE OF DEALING OR USAGE OF TRADE.
IN NO EVENT SHALL PALADIN LIGHT CONSTRUCTION BE LIABLE FOR CONSEQUENTIAL OR SPECIAL
DAMAGES.
IN NO EVENT SHALL PALADIN LIGHT CONSTRUCTION BE LIABLE FOR ANY LOSS OR CLAIM IN AN
AMOUNT IN EXCESS OF THE PURCHASE PRICE, OR, AT THE OPTION OF PALADIN LIGHT CONSTRUCTION,
THE REPAIR OR REPLACEMENT, OF THE PARTICULAR PRODUCT ON WHICH ANY CLAIM OF LOSS OR
DAMAGE IS BASED. THIS LIMITATION OF LIABILITY APPLIES IRRESPECTIVE OF WHETHER THE CLAIM
IS BASED ON BREACH OF CONTRACT, BREACH OF WARRANTY, NEGLIGENCE OR OTHER CAUSE AND
WHETHER THE ALLEGED DEFECT IS DISCOVERABLE OR LATENT.
Attachment Technologies Inc., a subsidiary of Paladin Brands Holding, Inc. (PBHI) is referred to herein as Paladin Light
Construction.
February 10, 2010
1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement