General Pump DCFSCP20, 2100303, DCFSCP20GZ Flat Surface Cleaner Operator's Manual

Below you will find brief information for Flat Surface Cleaner DCFSCP20, Flat Surface Cleaner 2100303. This operator's manual provides information about the operation and maintenance of the {detected_brand} Flat Surface Cleaner, a powerful tool ideal for cleaning large flat surfaces like patios, driveways, and decks. This guide includes safety information, operating instructions, parts list, and troubleshooting tips.

PDF Download

Document

AVAILABLE REPAIR KITS
Rotary Head Kit - Major:
P/N 2100202
Includes items 2, 3, 4, 5, 6, 7, 8, 9,
10, 11, 12, 13, 14, 15 and 17
Rotary Head Kit - Minor:
P/N 2100203
Includes items 9, 10, 15 and 17
PROFESSIONAL FLAT SURFACE CLEANER
Complete Rotary Head Kit:
P/N 2103000
Includes all items
FROM GENERAL PUMP
• COMPENSATING GUN FEATURE
• FULL 20” CLEANING PATH
• HEAVY-DUTY ANODIZED
ALUMINUM COMPONENTS
• RUGGED ABS COVER
ITEM
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
PART
NO.
2510017
2520030
2520028
2520031
2520027
2640004
2701012
2701011
2701010
2720007
2530008
2200037
2520029
2200038
2710000
2640012
2530007
DESCRIPTION
Housing, Swivel
Retainer, Bearing
Retainer, Bearing
Washer, Bearing Retainer
Spacer, Bearing
Bearing, 15 x 42
O-ring
O-ring
O-ring
Spring, Compression
Pin
Snap Ring
Snap Ring
Stem, Swivel
Back-up Ring
Zerk , Grease
Stem, Small
DCFSCP20
Model: 2100303
&amp; DCFSCP20GZ
OPERATOR’S MANUAL
QTY.
1
1
1
1
2
2
1
1
1
1
2
1
3
1
1
1
1
General Pump is a
member of the
Interpump Group
Ref 300843 Rev. B
09-12
WARNING: Read Before Operating Machine
Always wear protective eyewear
Keep clear of rotating nozzles
Never lock trigger gun open with any device
Drain water in cold weather to avoid freezing
Tampering with any part of this machine will void all warranties
8
Operating Instructions
1. Connect to Pressure Washer.
2. Turn water on and open valve. Open trigger gun for flow of water
through nozzles. Nozzles must have flowing spray. If not, remove
tips and clean; reassemble, making sure that groove of nozzle is
parallel to spray bar. Use thread sealant when installing nozzles.
3. Start Pressure Washer. The Hammerhead is ready for operation.
4. Walk slowly behind the Hammerhead cleaning as you go. If
striping occurs, slow down your pace.
5. Periodically check weep hole on bottom of swivel. Water will
seep slowly; if water shoots out, stop and replace seals. Swivel
assembly can be rebuilt.
6. For maximum effectiveness keep spray tips clean. If the machine
vibrates, stop and clean spray tips.
7. Grease the swivel with one or two grease gun pumps every 200
hours (or once about every 30 days of use).
DO NOT ALLOW MACHINE TO REMAIN STATIONARY
ON SOFT SURFACES SUCH AS WOOD.
Caution: Striking any raised obstacle during operation will damage
machine. If contact does occur and results in vibration when
operating machine, STOP and replace spray bar. Continued
operation could result in serious injury or damage to machine.
Operating Pressures: 1,000 to 4,000 PSI
Max Flow: 8.0 GPM
Dimensions: 70” x 21” x 21”
Weight: 21 lbs.
General Pump
1174 Northland Drive • Mendota Heights, MN 55120
Phone: 651.686.2199 • Fax: 800.535.1745
www.generalpump.com • [email protected]
Ref 300843 Rev. B
09-12
ITEM PART
NO. NO.
1
2
3
4
5
6
7
8
9
10
11
12
2103000
2660045
2530009
2630010
2540023
2200055
2200054
2540020
2200047
2203406
2540021
2540022
DESCRIPTION
Swivel
Deck, GP, 20”
Arm, Rotary, Assy., 20”
Plate, Retaining
Collar, Split
SHCS, M8
SHCS, M8
Block, Handle
Bolt, M6
Washer, M6
Handle, Lower
Handle, Upper
QTY.
1
1
1
1
1
4
1
2
8
8
1
1
ITEM PART
NO. NO.
DESCRIPTION
2660047 Grip, Handle
13
2660046 Plug, Handle
14
2660059 Brush Assy., 20”
15
16 DCG4000FSC Gun, Flat Surface Cleaner
17 2200053 Nut, M8 x 1.25
18
D10009 Plug
19
D10004 Coupler, 3/8 x 3/8-M
2200026 Nut, M6, Nylok
20
2202010 Pin, 55mm, w/Ring, SST
21
2200058 HHCS
22
2200018 Washer, M6
23
2203507
Washer
24
2702000 Hose, FSC, 20”
25
QTY.
1
1
1
1
4
1
1
2
2
2
4
1
1
">

Hello! I am an AI chatbot specifically trained to assist you with the General Pump DCFSCP20GZ Flat Surface Cleaner Operator's Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key features

20” cleaning path
Rugged ABS cover
Heavy-duty anodized aluminum components
Compensating gun feature

Frequently asked questions

Connect the Flat Surface Cleaner to the pressure washer using a hose with 3/8" connections. Turn on the water supply and open the valve. Open the trigger gun to check for water flow from the nozzle tips. If there is no flow, remove the tips, clean them, and reinstall them ensuring the groove of the nozzle is parallel to the spray bar.

The operating pressure for the Flat Surface Cleaner ranges from 1,000 to 4,000 PSI.

Grease the swivel with one or two grease gun pumps every 200 hours of operation, or approximately once every 30 days of use.

If the machine vibrates, stop operation and clean the spray tips. If the vibration persists, check for obstructions on the spray bar and replace it if necessary.