Accessories, COMPACT Unit & Top

Accessories, COMPACT Unit & Top
COMPACT
Unit & Top
COMPACT Unit & Top
COMPACT Unit
COMPACT Top
Contents
General..................................................................................................................... 42
Technical Description of the Air Handling Units......................................................... 44
Accessories............................................................................................................... 49
Specification............................................................................................................. 56
Sizing ...................................................................................................................... 58
COMPACT
COMPACT Unit and COMPACT Top
Have That Little Extra!
Introducing the new COMPACT series, Swegon offers air
handling units for small air volumes without having to
reduce standards of performance, energy efficiency, control functions and communications options.
Energy-efficient Fans
The fans in the COMPACT series are direct-driven plug
fans. They are equipped with EC motors that provide high
efficiency across the entire operating range.
The fans are compact and take up little space. Sharp duct
bends can be connected directly to the fan outlet without
pressure losses. The fans also generate low noise levels.
Heat Exchanger with High Efficiency
All of the units in the COMPACT series are equipped with
the RECOnomic rotary heat exchanger, one of the most
efficient heat exchangers on the market.
COMPACT Unit
The temperature efficiency of the RECOnomic is high, up
to 85%, and the pressure drop across it is low. The heat
exchanger is driven by a step motor that permits extremely high precision for controlling the rotor speed and heat
recovery efficiency as well.
Compact Filters
The air handling units are equipped with Class F7 socalled pleated filters for both the supply air and the extract air. Filter monitoring is built into the control system.
COMPACT Top
Unparalleled Flexibility
- COMPACT Top is often the best option when
space is restricted side to side and the ductwork is run from above.
- COMPACT Unit can be upended and you can
choose the direction of airflow. This provides
six different installation alternatives.
- Their low noise level makes it possible to install the units near utility areas and workplaces.
– Their attractive design makes it possible to
place the units where they can be seen.
42
Registered design. The company reserves the right to make design changes without prior notice.
20090901
www.swegon.com
COMPACT
The IQnomic Control System – An Intelligent
Economist on which You Can Always Rely!
Complete Control System
The IQnomic control system controls and regulates fans,
heat exchanger, temperatures, airflows and in-operation
periods. Every conceivable function for an air handling
unit is built into the system and is ready to activate.
All the settings and readings can be entered/viewed in
plain text via a user-friendly, hand-held micro terminal.
The fact that the control equipment is integrated into and
specifically developed for the COMPACT ensures that its
electronics and mechanics operate hand in hand.
Smart and Economical Control Functions
Hand-held
Micro Terminal
COMPACT Unit & Top
Typical smart and economical control functions available
only in the IQnomic from Swegon:
• ERS Regulation (control). Can be used when the
rooms served have surplus heat. In most cases, no reheating coil is needed.
• Density-corrected airflow. Automatically takes into
consideration how the air density varies and accordingly provides different air volume at different temperatures.
• Seasonally compensated airflow. The airflow can
be reduced in the winter according to a preset performance curve.
• Summer night cooling. An energy-saving function
for supplying cool outdoor air to the rooms at night.
• Cooling BOOST and Heating BOOST. The airflow
can be adjusted according to the cooling and heating
loads respectively.
• Cooling recovery. The heat exchanger is also automatically utilised for recovering the relative cooling
energy that can be present inside the room.
IQnomic
Communication Is Standard
Communication via TCP/IP and EIA 485 is included as
standard. The TBLZ Communication unit is used for
communication via LON and Trend.
The COMPACT also has built-in web communication.
Communication with the COMPACT can be established
via an ordinary web browser (such as Internet Explorer)
and your own network, i.e. without any main control
systems whatever.
In addition to the above, the COMPACT units have
inputs and outputs for external functions such as the
forwarding of alarms or overtime operation that can be
keyed in.
Registered design. The company reserves the right to make design changes without prior notice.
20090901www.swegon.com
43
COMPACT
Technical Description of the COMPACT Unit & Top Units
General
The COMPACT Unit and COMPACT Top units are complete air handling units with direct-driven supply air and
extract air fans, supply air and extract air filters, rotary
heat exchanger and built-in control equipment.
The two sizes have the same physical dimensions but different airflow capacity.
The COMPACT Unit has duct connections arranged on its
side panels. The COMPACT Top has all its duct connections arranged at the top of the unit.
The air handling unit is equipped with a pressure adjusting plate used for achieving a correct direction of air leakage across the heat exchanger. This prevents extract air
from being carried over to the supply air.
Built-in Control Equipment
The COMPACT Unit and COMPACT Top have built-in control equipment that can be operated from the hand-held
micro terminal with a clear-text display.
The electrical and control system is completely integrated into the air handling unit. The microprocessor-based
equipment controls and regulates temperatures, airflows
and other functions. A large number of functions are built
into the system and are simple to activate.
COMPACT Unit
Range of Application
The COMPACT Unit and COMPACT Top units are designed for comfort ventilation and can be used in offices,
schools, day nurseries, public premises, shops and residential buildings.
The COMPACT unit should be installed indoors.
The COMPACT is designed and tested for ambient temperatures from -25°C to +40°C, and temperatures in the
air stream from -40°C to +40°C.
The COMPACT Unit and COMPACT Top units generate
low noise levels. This makes it possible to install the units
near utility areas and workplaces.
The air handling units have an attractive and modest
design making them ideal for installation where they can
be seen in the premises.
Simple Installation
A standard installation is simple. Besides fitting the duct
system and air diffusers, the fitter only needs to connect the unit to a power supply and install a temperature
sensor inside the supply air duct.
Ready-to-use connection terminals and control functions
are provided for accessories such as dampers, air heaters
and air coolers.
COMPACT Top
Certification
Swegon AB has a certified Quality Assurance System that
conforms to ISO 9001 Standard and a certified Environmental Management System to ISO 14001.
The COMPACT Unit & Top air handling system is also certificated by Eurovent, No. AHU-09-05-426.
44
Registered design. The company reserves the right to make design changes without prior notice.
N° 09.05.426
Range: COMPACT
www.eurovent-certification.com
www.certiflash.com
20090901
www.swegon.com
COMPACT
Technical Description of the COMPACT Unit & Top Units
Mechanical Design
Casing
The room unit casing has an outer skin of galvanized
sheet steel that has been prepainted in a shade of white
(NCS S 0502-G), and has an inner skin of aluminium-zinc
plated sheet steel. The rear side of the COMPACT Top
consists of aluminium-zinc plated sheet steel.
The exterior surfaces of the room unit conform to Environmental Class C4. The casing has 30 mm thick mineral
wool insulation; the inspection door has 50 mm thick
insulation.
COMPACT Unit
The inspection door(s) is/are hung on hinges. The door(s)
is/are opened and closed using a special key. A lockable
door lock is available as an accessory.
Fans
The fans are effectively vibration-isolated from the casing.
They can be dismantled and removed from the air handling unit if required.
COMPACT Unit & Top
The fans are direct-driven plug fans. They are equipped
with EC motors that provide high efficiency across the
entire operating range. Flow measurement and control
are standard.
COMPACT Top
Heat exchanger
The rotary heat exchanger is of RECOnomic type, patented by Swegon. The heat exchanger is driven by a step
motor that controls the rotor speed with high precision
and controls the heat recovery efficiency as well.
The rotation monitor and controls are standard equipment.
It is available in a sorption version for moisture recovery,
which reduces operating and investment costs for cooling
and improves indoor comfort levels in the winter.
Direct-driven fans with EC motors.
Filters
The air handling unit has pleated Class F7 filters for both
the supply air and the extract air. Filter monitoring is built
into the control system.
Environmental Product Declaration
Swegon AB has a certified environmental management
system that conforms to ISO 14001 Standard and is registered on the REPA Register, no. 5560778465.
The COMPACT units are made of the following materials:
Type of Material
Percentage of total weight
Sheet steel
Approx. 80%
Aluminium
Approx. 8%
Polymeric material
Approx. 1%
Mineral wool insulation
Approx. 2%
Filter
Approx. 1%
Electronic equipment, motors
Approx. 8%
RECOnomic rotary heat exchanger.
Pleated Class F7 filter.
Registered design. The company reserves the right to make design changes without prior notice.
20090901www.swegon.com
45
COMPACT
Technical Description of the COMPACT Unit & Top Units
Electrical and Control System
General
The IQnomic control system is completely integrated into
the air handling unit. The microprocessor-based equipment controls and regulates temperatures, airflows and
other functions. A large number of functions are built into
the system and are simple to activate. See the special section entitled “Description of the Control System”.
The air handling unit can be automatically controlled in
several ways via the integrated time switch, however it
can also be demand-controlled via a CO2 sensor or presence detector. Manual control is also possible.
A large number of functions and settings can be also activated/entered via communication.
Control Inaccuracy:
Temperature ± 1oC.
Airflow ± 5%.
Power Efficiency
The design and performance of the air handling unit are
optimized for achieving excellent power efficiency.
IQnomic control unit
Standards
The air handling unit conforms to the provisions in the SSEN 60204-1 Standard.
Interference Level
The air handling units conform to the provisions of the
EMC Directive and are tested according to EN 61000-62 and EN 61000-6-3 Standards. (radiation in residential
buildings, office buildings, shops and similar indoor environments and for immunity in industrial facilities).
Use of an earth fault circuit breaker
The earth fault circuit breaker, if required, should only
serve the air handling unit and must be of a type designed for use with the control system of the EC motor.
Communication
Communication via TCP/IP and EIA 485 is included as
standard. The TBLZ Communication unit is used for communication via LON and Trend.
The COMPACT also has built-in web communication.
Communication with the COMPACT can be established
via an ordinary web browser (such as Internet Explorer)
and your own network, i.e. without any main control systems whatever.
In addition to the above, the COMPACT units have inputs
and outputs for external functions such as the forwarding
of alarms or overtime operation that can be keyed in.
Typical flow diagram for web communication.
46
Registered design. The company reserves the right to make design changes without prior notice.
20090901
www.swegon.com
COMPACT
Technical Description of the COMPACT Unit & Top Units
Electrical and Control System
Flow Diagrams
When you calculate performance data in the ProUnit AHU
selection program, the program furnishes a project-specific flow diagram and a description of the unit’s functions.
The individual components are specified below.
COMPACT Unit
COMPACT Top
COMPACT Unit & Top
Making a simple adjustment in the control equipment enables you to change
the directions of airflow through the COMPACT Unit at the building site(small
arrows). The relevant components automatically change function as well.
Outdoor air
Supply air
Extract air
Exhaust air
Components
V1
Outdoor air filter.
V2
Extract air filter.
BT3
Outdoor air temperature sensor. Indicates for control
of functions that affect temperature.
BT2
Extract air temperature sensor. Indicates for control
of functions that affect temperature.
E1
Variable speed-controlled RECOnomic rotary heat
exchanger with air purging operation.
G2
Direct-driven extract air fan with EC motor.
T2
M3
Step motor for variable speed control of the rotary
heat exchanger.
Motor control system for variable regulation of the
extract air fan
BF2
BG1
Rotation monitor sensor for monitoring the heat
exchanger’s rotation.
Extract air flow pressure sensor. Indicates for control
of the extract air fan’s speed and monitors the filter
status.
G1
Direct-driven supply air fan with EC motor.
K1
T1
Motor control system for variable regulation of the
supply air fan
IQnomic control unit containing control circuit card
and other electrical equipment for controlling internal and external functions.
BF1
Flow pressure sensor, supply air. Indicates for control
of the supply air fan’s speed and monitors the filter
status.
P1
Hand-held micro terminal for setting and reading airflows, temperatures, control functions, in-operation
periods, etc. as well as alarms.
BT1
Supply air temperature sensor. To be positioned in
the ductwork. Indicates for control of functions that
affect temperature.
Registered design. The company reserves the right to make design changes without prior notice.
20090901www.swegon.com
47
COMPACT
Technical Description of the COMPACT Unit & Top Units
Electrical and Control System
Hand-held micro terminal
All the settings and readings can be entered/viewed in
plain text via a user-friendly, hand-held micro terminal.
The hand-held micro terminal has keys for entering the
various commands. The display screen and the keys have
background lighting. A red indicating LED flashes in the
event of an alarm. The preset values are stored and will
not be affected in the event of a power failure.
The control panel contains logically composed menus arranged in various levels as follows:
• Main menu. Intended for reading the operating status
and for entering temporary changes in how the unit
operates.
• User level. Intended for entering settings and viewing
readings for the functions selected.
• Installation level. An access code is required (obtainable
in the maintenance instructions). Selection of functions
and the setting of limit values.
• Service level. An access code is required (disclosed on
completion of special training course).
MAIN MENU
OPERATION
SETTINGS
Hand-held micro terminal
AUTO OPERATION
MANUAL LOW SPEED
MANUAL HIGH SPEED
STOP
USER LEVEL
INSTALLATION LEVEL
SERVICE LEVEL
Principle structure of the menu system.
48
Registered design. The company reserves the right to make design changes without prior notice.
20090901
www.swegon.com
COMPACT
Accessories, COMPACT Unit & Top
Duct Accessories
General
The duct accessories must be positioned in the ductwork
outside the COMPACT unit. The unit’s fans make it possible to connect duct accessories directly to the unit's duct
connections without pressure losses or non-uniform air
distribution.
The duct accessories for the COMPACT are fitted with
rubber seal rings.
Other particulars for sizing can be obtained by using the
ProUnit air handling unit selection program.
TBSA Damper
Designed for preventing cold draughts while the air handling unit is switched off. The IQnomic controls the operation of the damper.
Installation
Can be mounted in a horizontal or vertical duct. Connect
the controls and power supply to the air handling unit’s
control unit.
COMPACT Unit & Top
Technical Data
Complete with damper actuator for 230 V. The actuator
can be selected with spring return or on/off actuation.
Tightness Class 3 to EN 1751 Standard.
70
50
250
125
Weight: 5 kg
TBDA Unit silencer
The TBDA unit silencer is a circular sound absorber designed for installation in a duct.
Technical Data
Made of galvanized sheet steel.
The sound attenuating material consists of 100 mm thick
mineral wool. This is covered with Fartex®, a patent-pending self-supporting surface layer, that has been approved
in terms of ease of cleaning, minimal fibre entrainment by
the airflow, resistance to ageing and minimal emissions.
The connection spigots are fitted with rubber seal rings.
Fire-resistance Class
The TBDA has been granted type approval (TG 0783)for
Fire-resistance Classes EI30/E120, EI60/E120 respectively.
EI120/E120 on condition that it is installed at a safe distance of 50 mm from a combustible structural element.
In buildings in which the safe distance from a combustible material and/or persons in an evacuation route is not
complied with, the TBDA then has Fire-resistance Class
EI60/E120.
Weight: 15 kg
Installation
Provision for inspection and cleaning must be guaranteed.
Registered design. The company reserves the right to make design changes without prior notice.
20090901www.swegon.com
49
COMPACT
Accessories, COMPACT Unit & Top
Duct accessories
TBLA Air heater, for hot water
The TBLA air heater is used, if required, for reheating the
supply air with hot water as the heating medium.
Technical Data
Uninsulated casing made of galvanized sheet steel.
Finned-tube heat exchangers fabricated of copper tubes
and profiled aluminium fins. The headers and the pipework to the water connections are made of copper.
The pipe connections are made of brass and have male
threads.
Accessories
Valve set/Set of electrical connection components
Valve set with 2(3)-way valve, actuator, anti-frost protection sensor and connection cable with quick-fit connector
can be ordered. If you install a valve of your own, you can
instead select a set of electrical connection components.
This set contains a connection cable with quick-fit connector, resistor and insertion or strap-on sensor.
Circulation pump
Circulation pump used for protecting the anti-frost protection monitor function for the air heater. Supplied with
T coupling, non-return valve and adjustment valve. The
automatic pump control system is integrated into the
COMPACT control equipment.
Installation
The TBLA air heater can be installed for horizontal or vertical airflow. Provision for inspection and cleaning must be
guaranteed.
60
The installation of accessories (if required), fitting of pipe
connections and filling the circuit with liquid must be
done at the building site.
60
390
Pipe connection, male threads, DN 15
Weight: 7 kg excluding liquid
Basic Installation Diagram
2(3)-way valve
Anti-frost protection sensor in T piece
Shut-off valve
T piece
Adjustment
valve
Heating Water
Non-return valve
Secondary pump
50
Shut-off valve
Registered design. The company reserves the right to make design changes without prior notice.
20090901
www.swegon.com
COMPACT
Accessories, COMPACT Unit & Top
Duct accessories
TBLE Electric air heater
The TBLE electric air heater is used reheating the supply
air.
Technical Data
Uninsulated casing made of galvanized sheet steel and
heating elements made of stainless material.
The TBLE air heater is available in two capacity variants.
The integrated thyristor is controlled via signals from the
COMPACT air handling unit. The TBLE has two series-coupled overheat protection devices. The electrical equipment conforms to the provisions of Degree of Protection
IP43.
COMPACT Unit & Top
Installation
The TBLE air heater can be installed for horizontal or vertical airflow.
Provision for inspection and cleaning must be guaranteed.
The end panel on the connection side can be dismantled
for inspection and wiring electrical connections.
The distance from or to a duct bend, damper, filter or
the like should be at least the distance that is equivalent
to double the diameter of the duct. Otherwise there is
risk that the airflow through the electric air heater will be
non-uniform, involving risk that the overheat protection
device will trip.
Power must be supplied directly from the electrical distribution box. Connect the control signal cable with quick-fit
connector to the air handling unit’s control unit.
Registered design. The company reserves the right to make design changes without prior notice.
Weight: 6 kg
20090901www.swegon.com
51
COMPACT
Accessories, COMPACT Unit & Top
Duct accessories
TBKA Air Cooler, for chilled water
TBKC Air cooler, direct expansion
The TBKA/TBKC air coolers are used for cooling the
supply air with chilled water or evaporative refrigerant as
the cooling medium.
The TBKA/TBKC air coolers are available in several capacity variants that cover existing needs for the COMPACT.
Technical Data
Uninsulated casing made of galvanized sheet steel.
The TBKA/TBKC air coolers consist of copper tubes and
profiled aluminium fins. The TBKA has water connections
made of copper/brass, with male connection threads. The
TBKC has water connections made of copper designed for
soldered joints.
Controls
An IQnomic plus module is required for controlling waterbased cooling. The IQnomic Plus is an extra module for
the air handling unit’s control system.
Water pipe connections, male threads, capacity variant 1: DN 15,
capacity variant 2: DN 20.
The regular outputs of the air handling unit are used for
cooling with direct expansion in one step. If this is not
sufficient then the IQnomic Plus should be used.
315
TBKA, chilled water
444
Accessories
Valve set
The TBVA Valve set consisting of a 2(3)-way valve including actuator can be ordered.
Installation
The TBKA/TBKC air cooler must be installed for horizontal airflow. Duct connections have a 315 mm diameter,
thus a 250-315 mm duct transition piece is required (not
included in the supply).
60
500
60
490
Pipe connection, drainage, male threads, DN 15.
Weight: Capacity variant 1, 21 kg,
capacity variant 2, 24 kg,
not including liquid
Provision for inspection and cleaning must be guaranteed.
TBKC (direct expansion)
The installation of accessories (if required), fitting of pipe
connections and filling the circuit with liquid must be
done at the building site.
D1: Refrigerant pipe connections,
smooth pipe end D1, male threads, 12 mm.
D2: Refrigerant pipe connections,
smooth pipe end D2, male threads, 12 mm.
D1
315
430
D2
60
500
60
490
Pipe connection, drainage, male threads, DN 15
Weight: 37 kg excluding liquid
52
Registered design. The company reserves the right to make design changes without prior notice.
20090901
www.swegon.com
COMPACT
Accessories, COMPACT Unit & Top
Roof Hoods
General
The roof ducts are made of galvanized sheet steel. Lined
inside with 50 mm thick insulation to Fire-resistance Class
EI30, with a surface covering of type-approved synthetic
woven fabric. Two angle brackets for connection to the
relevant roof slope are included.
The hoods are made of aluminium-zinc plated sheet steel
covered with a Plastisol (black) surface coating that conforms to Environmental Class C4.
The hoods have round duct connection, fitted with
rubber seal rings for spiral ducts. Duct connections have
a 315 mm diameter, thus a 250-315 mm duct transition
piece is required (not included in the supply).
TBHA Outdoor air hood
TBHB
Exhaust air hood
TBHA
Outdoor air hood
TBHB Exhaust air hood
Designed for the discharge of exhaust air. The hood can
be opened on hinges and is equipped with air deflectors
that effectively direct the exhaust air upward and give
the air high discharge velocity. To achieve low pressure
drop, the air deflectors are rounded off on both their long
sides. The hoods are equipped with effective provision for
drainage.
TBHC Dual-purpose hood
The TBHC is a combination of TBHA outdoor air hood and
TBHB exhaust air hood
TBHA Outdoor air hood and TBHB Exhaust air hood
850
TBHC
Dual-purpose hood
TBHC Dual-purpose hood
500
850
1000
620
620
2 angle brackets (unmounted) are supplied
with the hood.
800
Ø315
400
2 angle brackets (unmounted)
are suppled with
the hood.
800
Ø315
400
Weight: 31 kg
Registered design. The company reserves the right to make design changes without prior notice.
Ø315
900
400
Weight: 70 kg
20090901www.swegon.com
53
COMPACT Unit & Top
Designed for the intake of outdoor air. The design of the
hood makes it difficult for snow and rain drops to enter
the hood with the incoming air. The hood is hinged and
has air intake louvres on both sides.
COMPACT
Accessories, COMPACT Unit & Top
TBHF External wall hood
For the admission of outdoor air and the discharge of exhaust air.
The exhaust air is horizontally discharged through a circular wire mesh grille at the front of the hood. Outdoor air
is admitted through a wire mesh grille at the bottom of
the hood. This design effectively prevents short-circuit airflow between the outdoor air/exhaust air.
Made of aluminium-zinc plated sheet steel painted dark
grey, RAL 7021 (equivalent to NCSS 8502-B), Environmental Class C4.
Available in two variants, with or without acoustic insulation.
TBHF
A
B
C
D
Without acoust. insul.
440
683
167
185
With acoust. insul.
470
830
220
260
Mechanical equipment
B
310
C
171
A
D
Ø 250
Ø 250
60
Installation
The 250 mm dia. connections are fitted with rubber seal
rings. When you cut an opening in a wall, bear in mind
that the ducts must be insulated with at least 30 mm
thick insulation and with damp-proof outer layer material.
The front panel of the external wall hood can be lifted off
(after removing its screws), reversed and resecured. This
makes the duct connections for exhaust air and outdoor
air optional.
A
TBLZ Stand
Specially designed stand for the COMPACT Unit. The
height of the stand makes it possible to install ducts
under the air handling unit.
605
The stand is made of galvanized sheet steel profiled sections. The stand is supplied in assembly kit form. Can be
installed with or without legs. Height without feet: 100
mm.
The long sides (A in the illustration) are used for horizontal installation and the shorter sides (B) are used for vertical installation.
B
Stand. Two pairs of long sides are supplied. A is used for
horizontal installation and B is used for vertical installation.
TBLZ Cover holder
The cover holder is a practical accessory for the upper inspection door for COMPACT Unit installed vertically. The
cover holder consists of a mechanical stay with latch and
is supplied in unmounted condition.
TBLZ Door Lock
For use where more stringent demands on security are
made as opposed to locking with a standard special key.
Supplied in sets of 2 locks with key for replacement of the
existing lock at the building site.
54
Registered design. The company reserves the right to make design changes without prior notice.
20090901
www.swegon.com
COMPACT
Accessories, COMPACT Unit & Top
Electrical and control equipment
Pushbutton
Presence detector
For overtime operation when the unit’s built-in time
switch has controlled the unit to operate in the low speed
mode or to stop. For strap-on mounting. Can be selected
with or without indication.
To be connected to appropriate terminals on the control
unit.
For controlling high and low speed operation instead of
the unit’s built-in timer. As soon as the sensor registers
the presence of an occupant in the room, the air handling
unit is controlled to the high speed mode; when there are
no occupants, to the low speed mode.
To be connected via appropriate terminals on the control
unit.
Pressure sensor
Connection Cable
0.25-15 m for hand-held micro terminal, pressure transducer and IQnomic Plus.
For use in conjunction with the VAV pressure control
function, when constant pressure must be kept in the
ductwork. Also for use in conjunction with the heat exchanger defrosting function, when the pressure across
the heat exchanger must be controlled. The connection
cable is included. A 1–15 m long cable can be selected.
To be connected via appropriate terminals on the control
unit.
Extension Cable
Air quality sensor
Including holder and 3 m long cable
5-8 m long for air heater for hot water, electric air heater
and supply air temperature sensor, 8 m long for handheld micro terminal.
Extension kit for hand-held micro terminal
COMPACT Unit & Top
For lengthening the cable, 6-50 m
Extra hand-held micro terminal
For controlling high and low speed operation instead of
the unit’s built-in time switch. The air quality sensor registers the carbon dioxide content in the room air and the
control unit regulates the airflow required within preset
limits.
Available installation in a duct or in a room. To be connected to appropriate terminals on the control unit.
Strap-on sensor
VOC sensor
IQnomic Plus
Temperature sensor for mounting against the surface
where readings are to be taken.
SD card
For program transmissions and logging
For variable control of the airflow. The VOC sensor senses
the content of emissions/impurities in the room and the
airflow is regulated within preset limits.
The extra functions for which the inputs and outputs are
not included as standard in the unit’s control unit, for example external monitoring and cooling.
To be mounted inside the air handling unit. To be connected to appropriate terminals on the control unit.
TBLZ Communication unit
Room sensor
For use when the unit’s built-in extract air temperature
sensor does not provide representative values.
Designed for wall-mounting and is available for Enclosure
Class IP 20. To be connected to appropriate terminals on
the control unit.
Timer, Mechanical
For time-limited overtime operation when the unit’s builtin time switch has controlled the unit to operate in the low
speed mode or to stop.. For strap-on mounting.
To be connected to appropriate terminals on the control
unit.
Timer, electronic
For time-limited overtime operation when the unit’s builtin time switch has controlled the unit to operate in the low
speed mode or to stop. For strap-on mounting.
To be connected to appropriate terminals on the control
unit. Separate power supply
For communication via LON FTT-10 – Lon Works and
Trend (communication via TCP/IP and EIA 485 as well as
via internal webserver is standard in the COMPACT).
To be connected to the communication port of the control unit. Power can be supplied from appropriate terminals on the control unit.
Fire and smoke protection
The fire and smoke protection function consists of three
separate units:
• TBLZ Equipment cubicle
• TBLZ Smoke detector
• ELQZ* Damper actuator.
The cubicle contains the control unit and connections. The
smoke detector stops the air handling unit and controls
the damper actuators to close the dampers. An alarm is
presented in the hand-held micro terminal of the COMPACT air handling unit.
*) Applicable to installations in Sweden: The ELQZ damper
actuator can be used where type-approved solutions are
not required. If a type-approved solution is required, the
damper and actuator must be supplied as a unit in a typeapproved version. In these cases, a pump-exercising mode
is also required.
Registered design. The company reserves the right to make design changes without prior notice.
20090901www.swegon.com
55
COMPACT
Specification, COMPACT Unit & Top
Air handling unit
Duct accessories
Air handling unit, COMPACT Unit
Size 02
03
= 02
= 03
Heat exchanger standard = 1
sorption = 3
Air handling unit, COMPACT Top
Size 02
03
= 02
= 03
Heat exchanger standard = 1
sorption = 3
Air heater for hot water:
Duct connection size, 250 mm dia.
CU-aa-A-c-1
Valve set, cooling and heating
TBVL-3-aaa-b
2(3)-way valve including actuator, cable and
insertion-type sensor
Valve size:
Kvs 0.25
Kvs 0.40
Kvs 0.63
Insertion-type sensor
Strap-on sensor
Set of electrical connections:
For air heater for hot water
CT-aa-A-c-1
Set of filters, pleated filter, COMPACT
For supply air and extract air
TBFZ-1-07
Outdoor air hood
TBHA-1-031
Including roof duct, 315 mm dia. duct connection
Extract air hood
TBHB-1-031
Including roof duct, 315 mm dia. duct connection
Dual-purpose hood
TBHC-1-031
Including roof duct, 315 mm dia. duct connection
External wall hood
TBHF-2-0025-b
Combination hood for outdoor air/exhaust air
=0
With
=1
Mechanical equipment
Stand
Assembly kit (for COMPACT Unit only)
TBLZ-1-03-05
Cover holder
TBLZ-1-10-07
For the upper door for vertical installation (for COMPACT
Unit only)
Door lock
Set of two door locks with key.
TBLZ-1-57
Duct accessories
Damper with motor
TBSA-1-000-025-1-a
Tightness Class 3, 250 mm dia. duct connection,
uninsulated damper blades
=1
=2
Air handling unitsilencer
TBDA-1-000-025-080
Duct connection size, 250 mm dia., 800 mm long
56
=1
=2
TBLZ-1-27-a
= 1
=2
Circulation pump
TBPA-5-aaa
Set of pump components for the secondary side
for air heater without anti-frost protection, including non-return valve and adjustment valve.
Hoods
Damper motor:
With spring return
On/off
= 002
= 004
= 006
Cable, resistor and insertion sensor
Cable, resistor and strap on sensor
Replacement Material
Insulation
Without
TBLA-4-000-025-2-1
Capacity at max 25 kPa
pressure drop in air heater and pipework:
< 0.09 l/s =009
0.091-0.17 l/s
=017
Electric air heater
TBLE-3-000-025-bbb-c
Duct connection size, 250 mm dia.
Capacity variant:
2.1 kW (230 V only )
3.0 kW
Voltage:
400V
230V (Norway)
= 021
= 030
=1
=2
Air cooler, for chilled water
TBKA-4-000-031-1
Capacity variant 1. 315 mm dia. duct connection
Air cooler, for chilled water
TBKA-4-000-031-2
Capacity variant 2. 315 mm dia. duct connection
Valve set, cooling and heating
2(3)-way valve including actuator.
Valve size:
Kvs 0.25
Kvs 0.40
Kvs 0.63
Kvs 1.0
Kvs 1.6
Kvs 2.5
Kvs 4
Kvs 6.3
TBVA-1-aaa
= 002
= 004
= 006
= 010
= 016
= 025
= 040
= 063
Air cooler, direct expansion
TBKC-4-000-031-1-1
Duct connection size, 315 mm dia. 1 section.
Registered design. The company reserves the right to make design changes without prior notice.
20090901
www.swegon.com
COMPACT
Specification, COMPACT Unit & Top
Electrical and Control Equipment
Presence detector
TBLZ-1-56
Pressure sensor
TBLZ-1-23-aa
Contains pressure sensor and connection cable.
Version:
Sensor only
1 m
3 m
5 m
10 m
15 m
= 00
= 01
= 03
= 05
= 10
= 15
Air quality sensor, room
IQnomic Plus
Functional module and connection cable
ELQZ-2-504
VOC sensor
TBLZ-1-60-1-1
Timer, mechanical
For strap-on mounting.
0-2 hour prolonged operation
TBLZ-1-24-2
= 00
= 01
= 03
= 05
= 10
= 15
Modular/terminal adaptor
ELQZ-1-406-1
Timer, electronic
Version:
0.25 m
1 m
3 m
5 m
10 m
15 m
TBIQ-2-1-aa
TBLZ-1-47
TBLZ-1-55
Communication unit For interface:
LON FFT-10
Tend
TBLZ-3-1-a-41
=1
=2
Pushbutton for prolonged operation ELQZ-2-455-a-b
Version:
For surface mounting
=1
Without indicating LED
With indicating LED
=0
=1
Fire and smoke protection
Connection cable
TBLZ-1-26-aa
For hand-held micro terminal, pressure sensor, TBIQ
Version:
1 m
3 m
5 m
10 m
15 m
TBLZ-1-48-1
Control box for fire and
smoke protection function
TBLZ-2-48-2
Including control unit for smoke detector and damper
exercising, damper: 24 V AC Also requires the TBIQ accessory.
Including control unit for smoke detector
= 01
= 03
= 05
= 10
= 15
Connection cable
TBLZ-2-26-aa
For hand-held micro terminal, pressure sensor, TBIQ
Version:
0.45 m
Equipment cabinet for
fire and smoke protection function
Including control unit for smoke detector
Smoke detector, optical
Venturi tube, 600 mm
TBLZ-2-49-1
Mounting fittings for smoke detector,
for circular or insulated ducts
TBLZ-1-53
= 00
Extensioncable
With quick-fit connector
TBLZ-1-05-a
Version:
5 m long for air heater, electric or water coil = 1
5 m long for supply air sensor
= 2
8 m long for terminal, pressure sensor, TBIQ = 3
Damper actuator
With spring return
With spring return and
limit switch
ELQZ-1-428-3-a
=1
=2
Extension kit for hand-held micro terminal TBLZ-2-13
For extending the cable 6 – 50 m
Strap-on sensor
TBLZ-1-32
Registered design. The company reserves the right to make design changes without prior notice.
20090901www.swegon.com
57
COMPACT Unit & Top
Room sensor
For wall mounting. Enclosure Class IP 20.
SD card
TBLZ-1-62-a
Flash card for program transmissions and logging
Version:
Without COMPACT program = 1
With COMPACT program
=3
COMPACT
Sizing
COMPACT Unit, size 02
COMPACT Unit, size 03
Airflow, m3/h
Airflow, m3/h
SFP v - kW/(m3/s)
Available total pressure rise, Pa
Available total pressure rise, Pa
SFP v - kW/(m3/s)
Extract air fan
Supply air fan
Extract air fan
Supply air fan
Airflow, m3/s
Airflow, m3/s
Min. and Max. Airflows, COMPACT Air
COMPACT Unit
Correction factors KOK , dB
The tabulated flows are those that are possible to set. The
effect of external pressure drop determines the feasible flow
limits that can come into use.
Sound path
Octave band, No. / mid-frequency, Hz
1
2
3
4
5
6
7
8
63
125
250
500
1000
2000
4000
8000
To
outlet duct
-2
-3
-6
-10
-12
-10
-13
-18
To
inlet duct
-3
-3
-15
-19
-24
-29
-27
-26
-13
-17
-26
-31
-38
-43
-44
-45
To the unit’s
surroundings
58
COMPACT
Unit
Min. airflow
Max. airflow
m /h *
3
m /s
m3 /h*
m3 /s
02
300
0.08
800
0.23
03
300
0.08
1300
0.36
3
* When adjusting the flow,
round off the value to the nearest step.
Registered design. The company reserves the right to make design changes without prior notice.
20090901
www.swegon.com
COMPACT
Sizing
COMPACT Unit
Delivery and transport within the site
Electrical Data
Right-hand version
COMPACT Unit & Top
The air handling unit is delivered on a wooden pallet. The
inspection door and fans can be dismantled from the unit
to make it easier to transport the unit within the site.
The COMPACT Unit is produced in one single variant in
which all the components are arranged at their given
physical location inside the unit.
The air handling unit is supplied in the right-hand version.
The unit can be changed to the left-hand version at the
building site by making a simple adjustment in the control equipment. The air handling unit can also be upended
and which enables six different installation options as illustrated in the figure to the right.
The design of the COMPACT Unit makes it necessary to
mount it on a stand (available as accessories) or some
other form of base. Otherwise it will not be possible to
open the inspection doors. Swegon’s stand is specially designed and among other features has slots for the hinges
if the unit is installed vertically.
Left-hand version
Power supply
1-phase, 3-wire, 230 V -10/+15%, 50 Hz, 10 AT.
The unit is equipped with a main switch.
Rated data per fan
Size 02: 1 x 230 V, 50/60 Hz, 0.5 kW (0.28 kW)*
Size 03: 1 x 230 V, 50/60 Hz, 0.5 kW (0.43 kW)*
*) The motor controls limit the output power to the value
specified.
Outdoor air
Rated data for the heat exchanger drive motor
Step motor, 3-phase, 5.8 A (2A)*, 62 V max 90 V.
*) The motor control system limits the output power to
the value specified.
Supply air
Extract air
Exhaust air
Dimensions and Weights
COMPACT Unit, sizes 02 and 03.
4
Connection to Power Supply
788
50
1214
405
16
788
34
4
16
100
100
ø
25
0
ø
0
25
772 350
ø
350
25
0
ø
224
258
50
Weight
160 kg
285
245
607
245
738
772
0
25
198
285
738
258
50
Clear Space for Inspection
A clear space of 800 mm must be provided in front of the unit
for opening the inspection doors and at least 200 mm must be
provided above the unit for opening the junction hood.
Registered design. The company reserves the right to make design changes without prior notice.
20090901www.swegon.com
59
COMPACT
Sizing
COMPACT Top, size 02
COMPACT Top, size 03
Airflow, m3/h
Airflow, m3/h
SFP v - kW/(m3/s)
Available total pressure rise, Pa
Available total pressure rise, Pa
SFP v - kW/(m3/s)
Extract air fan
Supply air fan
Extract air fan
Supply air fan
Airflow, m3/s
Airflow, m3/s
Min. and max. airflows, COMPACT Top
The COMPACT Top Correction factors KOK , dB
The tabulated flows are those that are possible to set. The
effect of external pressure drop determines the feasible flow
limits that can come into use.
Sound path
Octave band, No. / mid-frequency, Hz
1
2
3
4
5
6
7
8
63
125
250
500
1000
2000
4000
8000
To
outlet duct
-2
-3
-6
-10
-12
-10
-13
-18
To
inlet duct
-3
-3
-15
-19
-24
-29
-27
-26
-13
-17
-26
-31
-38
-43
-44
-45
To the unit’s
surroundings
60
COMPACT
Top
Min. airflow
Max. airflow
m /h*
3
m /s
m3 /h*
m3 /s
02
300
0.08
800
0.23
03
300
0.08
1300
0.36
3
* When adjusting the flow,
round off the value to the nearest settable step.
Registered design. The company reserves the right to make design changes without prior notice.
20090901
www.swegon.com
COMPACT
Sizing
COMPACT Top
Delivery and transport within the site
The air handling unit is delivered on a wooden pallet. The
unit is equipped with base beams.
The inspection door and fans can be dismantled from the
unit to make it easier to transport the unit within the site.
The COMPACT Top unit is produced in one single variant
in which all the components are arranged at their given
physical location inside the unit. All the duct connections
are arranged from the top of the air handling unit.
Electrical Data
Power supply
1-phase, 3-wire, 230 V -10/+15%, 50 Hz, 10 AT.
The unit is equipped with a main switch.
COMPACT Unit & Top
Rated data per fan
Size 02: 1 x 230 V, 50/60 Hz, 0.5 kW (0.28 kW)*
Size 03: 1 x 230 V, 50/60 Hz, 0.5 kW (0.43 kW)*
*) The motor controls limit the output power to the value
specified.
Rated data for the heat exchanger drive motor
Step motor, 3-phase, 5.8 A (2A)*, 62 V max 90 V.
*) The motor control system limits the output power to
the value specified.
Dimensions and Weights
COMPACT Top, sizes 02 and 03.
1103
16
788
4
917
736
34
1302
90
9
60
110
718
883
210
ø 250 (x4)
170
360
170 201
350
Connection to
Power Supply
Weight
Outdoor air
Supply air
Extract air
Exhaust air
Circulation air
200 kg
Clear Space for Inspection
A clear space of 1,000 mm should be provided in front of the
unit for opening the inspection door (right hung).
Registered design. The company reserves the right to make design changes without prior notice.
20090901www.swegon.com
61
COMPACT
62
Registered design. The company reserves the right to make design changes without prior notice.
20090901
www.swegon.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement