Visio-StudioHub Cross Reference Pinout.vsd

Visio-StudioHub Cross Reference Pinout.vsd
StudioHub+
Pinout Guide
StudioHub+ Adapter Pinout Guide
LEFT
1
XLR
Male
ADAPT-XLRM
ADAPT-XLRF
Balanced
2
3
2
1
RIGHT
1
2- Positive
3- Negative
Pin-1
Pin-2
Shield
1- Ground
Pin-3
Pin-6
Shield
2- Positive
3- Negative
Male
2
3
2
1- Ground
3
1
3
Female
Female
TRS - 1/4” or 1/8”
Ring
Tip
ADAPT-XLRM
ADAPT-XLRF
TRS - 1/4” or 1/8”
Shield
Tip/+
Ring/ –
Ground
Pin-1
Pin-3
Pin-2
Shield
Pin-6
Shield
Tip/+
Ring/ –
Ground
Ring
Shield
ADAPT-TRS
ADAPT-MINI
Tip
ADAPT-TRS
ADAPT-MINI
RJ-45 Male
RJ-45 Male
Positive
Negative
Ground
2- Positive
3- Negative
1- Ground
Pin-1
Pin-2
Shield
Pin-3
Pin-6
Shield
2- Positive
3- Negative
1- Ground
Positive
Negative
Ground
ADAPT-PIGTAIL
ADAPT-PIGTAIL
Unbalanced
RCA or Phono
Positive
XLR
Shield
Positive
Shield/G
Pin-1
Pin-2
Shield
RCA or Phono
Pin-3
Pin-6
Shield
Positive
Shield/G
Shield
ADAPT-RCA
Positive
ADAPT-RCA
Stereo TRS - 1/8”
Tip
Ring
ADAPT-MINIUNBAL
Shield
Tip (Left)
n/c
Ring (Right)
n/c
Shield
Pin-1
Pin-2
Pin-3
Pin-6
Shield/G
®
601 Heron Drive · Logan Township, NJ 08085
(856) 467-8000 · Fax (856) 467-3044
www.studiohub.com
www.radiosystems.com
Connecting StudioHub+ inputs and outputs to non-balanced devices
When possible, use MatchJack balancing amplifiers, or proceed as follows:
Type 1 - Electronic Balanced Floating or Transformer Floating Output to Unbalanced Input
OUT
OUT
1
2
3
4
5
6
7
8
Shield
L+
R+
StudioHub+ Premade Adapters MAY BE Utilized
1
2
3
4
5
6
7
8
IN
MINI TRS (1/8”)
Stereo
Shield
+
IN
Shield
+
RCA (Phono)
Left
IN
RCA (Phono)
Right
IN
MINI TRS (1/8”)
Stereo
Shield
+
IN
Shield
+
RCA (Phono)
Left
IN
RCA (Phono)
Right
Type 2 - Electronic Balanced Non-Floating Output to Unbalanced Input
OUT
OUT
1
2
3
4
5
6
7
8
Shield
L+
R+
StudioHub+ Premade Adapters MAY NOT BE Utilized
Custom make an adapter using an ADAPT-TAIL
1
2
3
4
5
6
7
8
Type 3 - Unbalanced Output to Balanced Input
MINI TRS (1/8”)
Stereo
Shield
L+
R+
OUT
StudioHub+ Premade Adapters MAY BE Utilized
OUT
Shield
+
RCA (Phono) OUT
Right
Shield
+
RCA (Phono)
Left
1
2
3
4
5
6
7
8
IN
1
2
3
4
5
6
7
8
IN
Connecting balanced outputs to an unbalanced inputs (DESTINATIONS)
Determine the type of circuit of your device before choicing your connection configuration
Electronic balanced floating type - SEE TYPE 1 This is the topology of the differential instrumentation chips such as made
by Texas Instruments, Analog Devices & THAT Corp.
This is also the output topology used in most StudioHub+ products.
Connect the "-" output pin to ground (shield) as shown.
The output level will not change, but the headroom will decrease by 6dB.
Transformer balanced floating type -SEE TYPE 1 this is the topology of the standard transformer
(non electronic) balanced outputs.
This technology is found on legacy gear and some very high end new equipment.
Connect the "-" output pin to ground (shield) as shown.
The output level will not change, and the headroom will not change.
Electronic balanced non floating type - SEE TYPE 2 this is the topology of the more typical “5532” type op-amp chip.
This is also the output topology used in the Radio Systems DA4x4a, Millenium A Console, etc.
DO NOT connect the "-" output pin to ground (shield) as shown.
The output will be reduced by 6dB but the headroom will not change.
Connecting unbalanced output signals to balanced inputs (SOURCES)
SEE TYPE 3 - Connect the "-" output pin to ground (shield) as shown.
StudioHub+ Premade Adapters
These premade adapters connect the negative lead to shield.
Use only for connection Types 1 & 3 above.
Part #: ADAPT-MINIUNBAL
®
601 Heron Drive · Logan Township, NJ 08085
(856) 467-8000 · Fax (856) 467-3044
Part #: ADAPT-RCAM
www.studiohub.com
www.radiosystems.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising