YP400Z - Yamaha
Read this manual carefully before operating this vehicle.
OWNER’S MANUAL
YP400Z
LIT-11626-23-11
34B-28199-11
EAU10042
Q Read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold.
INTRODUCTION
EAU10092
Congratulations on your purchase of the Yamaha YP400Z. This model is the result of Yamaha’s vast experience in the production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and reliability that have made Yamaha a leader in these fields.
This manual will give you an understanding of the operation, inspection, and basic maintenance of this scooter. If you have
any questions concerning the operation or maintenance of your scooter, please consult a Yamaha dealer.
The design and manufacture of this Yamaha scooter fully comply with the emissions standards for clean air applicable at the
date of manufacture. Yamaha has met these standards without reducing the performance or economy of operation of the
scooter. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to the recommended maintenance schedules and operating instructions contained within this manual.
Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most current product information available at the time of printing, there may be minor discrepancies between your scooter and this
manual. If there is any question concerning this manual, please consult a Yamaha dealer.
EWA12581
WARNING
Please read this manual and the “YOU AND YOUR MOTORCYCLE: RIDING TIPS” booklet carefully and completely
before operating this scooter. Do not attempt to operate this scooter until you have attained adequate knowledge
of its controls and operating features and until you have been trained in safe and proper riding techniques. Regular
inspections and careful maintenance, along with good riding skills, will ensure that you safely enjoy the capabilities
and reliability of this scooter.
IMPORTANT MANUAL INFORMATION
EAU10132
Particularly important information is distinguished in this manual by the following notations:
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury
or death.
WARNING
NOTICE
TIP
A WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
A NOTICE indicates special precautions that must be taken to avoid damage to the
vehicle or other property.
A TIP provides key information to make procedures easier or clearer.
IMPORTANT MANUAL INFORMATION
EAU10193
YP400Z
OWNER’S MANUAL
©2009 by Yamaha Motor Corporation, U.S.A.
1st edition, February 2009
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Corporation, U.S.A.
is expressly prohibited.
Printed in Japan.
P/N LIT-11626-23-11
TABLE OF CONTENTS
LOCATION OF IMPORTANT
LABELS ............................................. 1-1
SAFETY INFORMATION .................. 2-1
Further safe-riding points ................ 2-5
DESCRIPTION ..................................
Left view ..........................................
Right view ........................................
Controls and instruments.................
3-1
3-1
3-2
3-3
INSTRUMENT AND CONTROL
FUNCTIONS ....................................... 4-1
Main switch/steering lock ................ 4-1
Indicator and warning lights ............ 4-2
Speedometer .................................. 4-2
Tachometer .................................... 4-3
Multi-function display ...................... 4-3
Handlebar switches ........................ 4-7
Front brake lever ............................ 4-8
Rear brake lever ............................. 4-8
Rear brake lock lever ...................... 4-8
Fuel tank cap .................................. 4-9
Fuel ............................................... 4-10
Catalytic converter ........................ 4-11
Seats ............................................ 4-12
Adjusting the rider seat ................. 4-13
Storage compartments ................. 4-14
Adjusting the shock absorber
assemblies ................................ 4-16
Sidestand ...................................... 4-16
Ignition circuit cut-off system ........ 4-17
FOR YOUR SAFETY – PREOPERATION CHECKS ...................... 5-1
OPERATION AND IMPORTANT
RIDING POINTS .................................
Starting the engine .........................
Starting off ......................................
Acceleration and deceleration ........
Braking ...........................................
Engine break-in ..............................
Parking ...........................................
6-1
6-1
6-2
6-2
6-3
6-3
6-4
PERIODIC MAINTENANCE AND
ADJUSTMENT ................................... 7-1
Owner’s tool kit ............................... 7-2
Periodic maintenance chart for the
emission control system ............. 7-3
General maintenance and
lubrication chart .......................... 7-4
Removing and installing cowlings
and panels .................................. 7-8
Checking the spark plug ............... 7-12
Canister ........................................ 7-14
Engine oil and oil filter element .... 7-14
Final transmission oil .................... 7-17
Coolant ......................................... 7-18
Air filter elements and check
hoses and V-belt case air
filter element ............................. 7-19
Checking the throttle cable free
play ...........................................
Valve clearance ...........................
Tires .............................................
Cast wheels .................................
Front and rear brake lever free
play ...........................................
Adjusting the rear brake lock
lever cable ................................
Checking the front and rear brake
pads ..........................................
Checking the brake fluid level ......
Changing the brake fluid ..............
Checking and lubricating the
cables .......................................
Checking and lubricating the
throttle grip and cable ...............
Lubricating the front and rear
brake levers ..............................
Checking and lubricating the
centerstand and sidestand .......
Checking the front fork .................
Checking the steering ..................
Checking the wheel bearings .......
Battery ..........................................
Replacing the fuses .....................
Replacing a headlight bulb ..........
Tail/brake light ..............................
Replacing a front turn signal
light bulb ...................................
7-22
7-22
7-23
7-24
7-25
7-26
7-26
7-27
7-28
7-28
7-29
7-29
7-29
7-30
7-31
7-31
7-31
7-33
7-34
7-34
7-35
TABLE OF CONTENTS
Replacing a rear turn signal light
bulb ...........................................
Replacing the license plate light
bulb ...........................................
Troubleshooting ............................
Troubleshooting charts .................
7-36
7-36
7-37
7-38
SCOOTER CARE AND STORAGE ...
Matte color caution .........................
Care ................................................
Storage ...........................................
8-1
8-1
8-1
8-3
SPECIFICATIONS ............................. 9-1
CONSUMER INFORMATION...........
Identification numbers ..................
Reporting safety defects ...............
Scooter noise regulation ...............
Maintenance record ......................
YAMAHA MOTOR
CORPORATION, U.S.A.
STREET AND ENDURO
MOTORCYCLE LIMITED
WARRANTY ..............................
YAMAHA EXTENDED SERVICE
(Y.E.S.) .....................................
10-1
10-1
10-3
10-4
10-5
10-7
10-9
LOCATION OF IMPORTANT LABELS
EAU10383
1
Read and understand all of the labels on your vehicle. They contain important information for safe and proper operation of
your vehicle. Never remove any labels from your vehicle. If a label becomes difficult to read or comes off, a replacement label
is available from your Yamaha dealer.
1 2 3 4 5 6
8
1-1
7
LOCATION OF IMPORTANT LABELS
1
2
WARNING
NOTICE
BEFORE YOU OPERATE THIS VEHICLE, READ
THE OWNER’S MANUAL AND ALL LABELS.
ALWAYS WEAR AN APPROVED MOTORCYCLE
HELMET, eye protection, and protective clothing.
Cleaning with alkaline or acid cleaner,
gasoline or solvent will damage windshield.
Use neutral detergent.
8ET—2815K—00
5GK-2118K-00
3
4
5
LOAD LIMIT
Improper loading can cause loss of control.
Read owner’s manual for proper loading.
5RU-24877-A0
2
3
WARNING
2 kg {4 lbs}
1
4
3JJ—28446—A1
5
6
5RU-21668-00
7
6
8
7
LOAD LIMIT
5 kg {11 lbs}
8
3LD-24877-A0
9
5RU-21686-00
1-2
SAFETY INFORMATION
EAU10263
1
2
3
4
5
6
7
8
9
Be a Responsible Owner
As the vehicle’s owner, you are responsible for the safe and proper operation
of your scooter.
Scooters are single-track vehicles.
Their safe use and operation are dependent upon the use of proper riding
techniques as well as the expertise of
the operator. Every operator should
know the following requirements before
riding this scooter.
He or she should:
● Obtain thorough instructions from
a competent source on all aspects
of scooter operation.
● Observe the warnings and maintenance requirements in this Owner’s Manual.
● Obtain qualified training in safe
and proper riding techniques.
● Obtain professional technical service as indicated in this Owner’s
Manual and/or when made necessary by mechanical conditions.
Safe Riding
Perform the pre-operation checks each
time you use the vehicle to make sure it
is in safe operating condition. Failure to
inspect or maintain the vehicle properly
increases the possibility of an accident
or equipment damage. See page 5-1
for a list of pre-operation checks.
● This scooter is designed to carry
the operator and a passenger.
● The failure of motorists to detect
and recognize scooters in traffic is
the predominating cause of automobile/scooter accidents. Many
accidents have been caused by an
automobile driver who did not see
the scooter. Making yourself conspicuous appears to be very effective in reducing the chance of this
type of accident.
Therefore:
Wear a brightly colored jacket.
Use extra caution when you are
approaching
and
passing
through intersections, since intersections are the most likely
places for scooter accidents to
occur.
●
●
2-1
Ride where other motorists can
see you. Avoid riding in another
motorist’s blind spot.
Many accidents involve inexperienced operators. In fact, many operators who have been involved in
accidents do not even have a current driver’s license.
Make sure that you are qualified
and that you only lend your
scooter to other qualified operators.
Know your skills and limits.
Staying within your limits may
help you to avoid an accident.
We recommend that you practice riding your scooter where
there is no traffic until you have
become thoroughly familiar with
the scooter and all of its controls.
Many accidents have been caused
by error of the scooter operator. A
typical error made by the operator
is veering wide on a turn due to excessive speed or undercornering
(insufficient lean angle for the
speed).
●
●
●
●
●
●
SAFETY INFORMATION
Always obey the speed limit and
never travel faster than warranted by road and traffic conditions.
Always signal before turning or
changing lanes. Make sure that
other motorists can see you.
The posture of the operator and
passenger is important for proper
control.
The operator should keep both
hands on the handlebar and
both feet on the operator footrests during operation to maintain control of the scooter.
The passenger should always
hold onto the operator, the seat
strap or grab bar, if equipped,
with both hands and keep both
feet on the passenger footrests.
Never carry a passenger unless
he or she can firmly place both
feet on the passenger footrests.
Never ride under the influence of
alcohol or other drugs.
This scooter is designed for
on-road use only. It is not suitable
for off-road use.
●
●
●
●
●
●
●
Protective apparel
The majority of fatalities from scooter
accidents are the result of head injuries. The use of a safety helmet is the
single most critical factor in the prevention or reduction of head injuries.
● Always wear an approved helmet.
● Wear a face shield or goggles.
Wind in your unprotected eyes
could contribute to an impairment
of vision that could delay seeing a
hazard.
● The use of a jacket, substantial
shoes, trousers, gloves, etc., is effective in preventing or reducing
abrasions or lacerations.
● Never wear loose-fitting clothes,
otherwise they could catch on the
control levers or wheels and cause
injury or an accident.
● Always wear protective clothing
that covers your legs, ankles, and
feet. The engine or exhaust system become very hot during or after operation and can cause burns.
● A passenger should also observe
the above precautions.
2-2
Avoid Carbon Monoxide Poisoning
All engine exhaust contains carbon
monoxide, a deadly gas. Breathing carbon monoxide can cause headaches,
dizziness, drowsiness, nausea, confusion, and eventually death.
Carbon Monoxide is a colorless, odorless, tasteless gas which may be
present even if you do not see or smell
any engine exhaust. Deadly levels of
carbon monoxide can collect rapidly
and you can quickly be overcome and
unable to save yourself. Also, deadly
levels of carbon monoxide can linger
for hours or days in enclosed or poorly
ventilated areas. If you experience any
symptoms of carbon monoxide poisoning, leave the area immediately, get
fresh air, and SEEK MEDICAL TREATMENT.
● Do not run engine indoors. Even if
you try to ventilate engine exhaust
with fans or open windows and
doors, carbon monoxide can rapidly reach dangerous levels.
● Do not run engine in poorly ventilated or partially enclosed areas
such as barns, garages, or car-
2
3
4
5
6
7
8
9
SAFETY INFORMATION
●
1
2
3
4
5
6
7
8
9
ports.
Do not run engine outdoors where
engine exhaust can be drawn into
a building through openings such
as windows and doors.
Loading
Adding accessories or cargo to your
scooter can adversely affect stability
and handling if the weight distribution of
the scooter is changed. To avoid the
possibility of an accident, use extreme
caution when adding cargo or accessories to your scooter. Use extra care
when riding a scooter that has added
cargo or accessories. Here, along with
the information about accessories below, are some general guidelines to follow if loading cargo to your scooter:
The total weight of the operator, passenger, accessories and cargo must
not exceed the maximum load limit.
Operation of an overloaded vehicle
could cause an accident.
Maximum load:
196 kg (432 lb)
When loading within this weight limit,
keep the following in mind:
● Cargo and accessory weight
should be kept as low and close to
the scooter as possible. Securely
pack your heaviest items as close
to the center of the vehicle as possible and make sure to distribute
the weight as evenly as possible
on both sides of the scooter to minimize imbalance or instability.
● Shifting weights can create a sudden imbalance. Make sure that accessories and cargo are securely
attached to the scooter before
riding. Check accessory mounts
and cargo restraints frequently.
Properly adjust the suspension
for your load (suspension-adjustable models only), and
check the condition and pressure of your tires.
Never attach any large or heavy
items to the handlebar, front
fork, or front fender. Such items
can create unstable handling or
a slow steering response.
● This vehicle is not designed to
pull a trailer or to be attached to
●
a sidecar.
Genuine Yamaha Accessories
Choosing accessories for your vehicle
is an important decision. Genuine
Yamaha accessories, which are available only from a Yamaha dealer, have
been designed, tested, and approved
by Yamaha for use on your vehicle.
Many companies with no connection to
Yamaha manufacture parts and accessories or offer other modifications for
Yamaha vehicles. Yamaha is not in a
position to test the products that these
aftermarket
companies
produce.
Therefore, Yamaha can neither endorse nor recommend the use of accessories not sold by Yamaha or
modifications not specifically recommended by Yamaha, even if sold and
installed by a Yamaha dealer.
●
2-3
Aftermarket Parts, Accessories,
and Modifications
While you may find aftermarket products similar in design and quality to
genuine Yamaha accessories, recognize that some aftermarket accessories
SAFETY INFORMATION
or modifications are not suitable because of potential safety hazards to you
or others. Installing aftermarket products or having other modifications performed to your vehicle that change any
of the vehicle’s design or operation
characteristics can put you and others
at greater risk of serious injury or death.
You are responsible for injuries related
to changes in the vehicle.
Keep the following guidelines in mind,
as well as those provided under “Loading” when mounting accessories.
● Never install accessories or carry
cargo that would impair the performance of your scooter. Carefully
inspect the accessory before using
it to make sure that it does not in
any way reduce ground clearance
or cornering clearance, limit suspension travel, steering travel or
control operation, or obscure lights
or reflectors.
Accessories fitted to the handlebar or the front fork area can
create instability due to improper
weight distribution or aerodynamic changes. If accessories
●
are added to the handlebar or
front fork area, they must be as
lightweight as possible and
should be kept to a minimum.
Bulky or large accessories may
seriously affect the stability of
the scooter due to aerodynamic
effects. Wind may attempt to lift
the scooter, or the scooter may
become unstable in cross
winds. These accessories may
also cause instability when
passing or being passed by
large vehicles.
Certain accessories can displace the operator from his or
her normal riding position. This
improper position limits the freedom of movement of the operator and may limit control ability,
therefore, such accessories are
not recommended.
Use caution when adding electrical accessories. If electrical accessories exceed the capacity of the
scooter’s electrical system, an
electric failure could result, which
could cause a dangerous loss of
●
lights or engine power.
Aftermarket Tires and Rims
The tires and rims that came with your
scooter were designed to match the
performance capabilities and to provide
the best combination of handling, braking, and comfort. Other tires, rims, sizes, and combinations may not be
appropriate. Refer to page 7-23 for tire
specifications and more information on
replacing your tires.
2
3
4
5
●
●
2-4
6
7
8
9
SAFETY INFORMATION
EAU10372
Further safe-riding points
●
1
●
2
3
4
●
●
5
●
6
7
8
9
●
●
Be sure to signal clearly when
making turns.
Braking can be extremely difficult
on a wet road. Avoid hard braking,
because the scooter could slide.
Apply the brakes slowly when
stopping on a wet surface.
Slow down as you approach a corner or turn. Once you have completed a turn, accelerate slowly.
Be careful when passing parked
cars. A driver might not see you
and open a door in your path.
Railroad crossings, streetcar rails,
iron plates on road construction
sites, and manhole covers become extremely slippery when
wet. Slow down and cross them
with caution. Keep the scooter upright, otherwise it could slide out
from under you.
The brake pads could get wet
when you wash the scooter. After
washing the scooter, check the
brakes before riding.
Always wear a helmet, gloves,
trousers (tapered around the cuff
●
and ankle so they do not flap), and
a bright colored jacket.
Do not carry too much luggage on
the scooter. An overloaded scooter is unstable. Use a strong cord to
secure any luggage to the carrier
(if equipped). A loose load will affect the stability of the scooter and
could divert your attention from the
road. (See page 2-1.)
2-5
DESCRIPTION
EAU10410
Left view
1
2
3
4
5
6
7
2
3
4
5
6
7
11
1.
2.
3.
4.
5.
6.
7.
Headlight (page 7-34)
Fuel tank cap (page 4-9)
Rear storage compartment (page 4-14)
V-belt case air filter element (page 7-19)
Owner’s tool kit (page 7-2)
Fuses (page 7-33)
Battery (page 7-31)
10
9
8
8. Shock absorber assembly spring preload adjusting ring (page 4-16)
9. Air filter element (left) (page 7-19)
10.Engine oil filter element (page 7-14)
11.Sidestand (page 4-16, 7-29)
3-1
8
9
DESCRIPTION
EAU10420
Right view
1
4
3
2
1
2
3
4
5
6
7
8
8
9
1.
2.
3.
4.
5.
6.
7.
7
6
5
Grab bar (page 6-2)
Passenger seat (page 4-12)
Rider seat (page 4-12)
Coolant reservoir (page 7-18)
Radiator
Centerstand (page 7-29)
Air filter element (right) (page 7-19)
8. Shock absorber assembly spring preload adjusting ring (page 4-16)
3-2
DESCRIPTION
EAU10430
Controls and instruments
1
2
3
4
5
6
7
8
2
3
4
5
6
7
12
1.
2.
3.
4.
5.
6.
7.
Rear brake lever (page 4-8)
Left handlebar switches (page 4-7)
Rear brake lock lever (page 4-8)
Speedometer (page 4-2)
Multi-function display (page 4-3)
Tachometer (page 4-3)
Right handlebar switches (page 4-7)
11
10
9
8. Front brake lever (page 4-8)
9. Throttle grip (page 7-22)
10.Front storage compartment B (page 4-14)
11.Main switch/steering lock (page 4-1)
12.Front storage compartment A (page 4-14)
3-3
8
9
INSTRUMENT AND CONTROL FUNCTIONS
EAU10460
Main switch/steering lock
sidestand is moved down.
EAU10661
OFF
All electrical systems are off. The key
can be removed.
1
EWA10061
2
3
4
5
6
7
8
9
The main switch/steering lock controls
the ignition and lighting systems, and is
used to lock the steering. The various
positions are described below.
EAU36070
ON
All electrical circuits are supplied with
power; the meter lighting, taillight, license plate light and position lights
come on, and the engine can be started. The key cannot be removed.
TIP
The headlights come on automatically
when the engine is started and stay on
until the key is turned to “OFF” or the
WARNING
Never turn the key to “OFF” or
“LOCK” while the vehicle is moving.
Otherwise the electrical systems will
be switched off, which may result in
loss of control or an accident.
EAU10681
LOCK
The steering is locked, and all electrical
systems are off. The key can be removed.
To lock the steering
1. Turn the handlebars all the way to
the left.
2. Push the key in from the “OFF” position, and then turn it to “LOCK”
while still pushing it.
3. Remove the key.
4-1
To unlock the steering
Push the key in, and then turn it to
“OFF” while still pushing it.
INSTRUMENT AND CONTROL FUNCTIONS
EAU11004
Indicator and warning lights
1
2 3
1. Turn signal indicator lights “ ” and “
2. High beam indicator light “
”
3. Engine trouble warning light “
”
”
EAU11484
Engine trouble warning light “ ”
This warning light comes on if a problem is detected in the electrical circuit
monitoring the engine. If this occurs,
have a Yamaha dealer check the
self-diagnosis system.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”. The warning light should come
on for a few seconds, and then go off.
If the warning light does not come on
initially when the key is turned to “ON”,
or if the warning light remains on, have
a Yamaha dealer check the electrical
circuit.
EAU11030
Turn signal indicator lights “ ” and
“ ”
The corresponding indicator light flashes when the turn signal switch is
pushed to the left or right.
EAU11601
Speedometer
1
2
3
1. Speedometer
The speedometer shows the riding
speed.
When the key is turned to “ON”, the
speedometer needle will sweep once
across the speed range and then return
to zero in order to test the electrical circuit.
4
5
6
7
8
EAU11080
9
High beam indicator light “ ”
This indicator light comes on when the
high beam of the headlight is switched
on.
4-2
INSTRUMENT AND CONTROL FUNCTIONS
EAU11872
Tachometer
EAU36109
1
Multi-function display
2
3
4
EWA12312
1
1
2
2
3
4
5
6
7
8
1
2
3
1. Tachometer
2. Tachometer red zone
The electric tachometer allows the rider
to monitor the engine speed and keep it
within the ideal power range.
When the key is turned to “ON”, the tachometer needle will sweep once
across the r/min range and then return
to zero r/min in order to test the electrical circuit.
ECA10031
9
WARNING
Be sure to stop the vehicle before
making any setting changes to the
multi-function display. Changing
settings while riding can distract the
operator and increase the risk of an
accident.
NOTICE
Do not operate the engine in the tachometer red zone.
Red zone: 8250 r/min and above
4
5
6
1.
2.
3.
4.
5.
6.
Clock/ambient temperature display
Coolant temperature meter
Fuel meter
Odometer/tripmeters
“SELECT” button
“RESET” button
4-3
1. V-belt replacement indicator “V-BELT”
2. Fuel level warning indicator “ ”
3. Coolant temperature warning indicator
“ ”
4. Oil change indicator “OIL”
The multi-function display is equipped
with the following:
● a fuel meter
● a coolant temperature meter
● an odometer
● two tripmeters (which show the
distance traveled since they were
last set to zero)
● a fuel reserve tripmeter (which
shows the distance traveled since
the bottom segment of the fuel
meter and fuel level warning indicator started flashing)
INSTRUMENT AND CONTROL FUNCTIONS
●
●
●
●
●
a self-diagnosis device
a clock
an ambient temperature display
an oil change indicator
a V-belt replacement indicator
TIP
●
●
Be sure to turn the key to “ON” before using the “SELECT” and
“RESET” buttons.
When the key is turned to “ON”, all
of the display segments of the
multi-function display will appear
one after the other and then disappear, in order to test the electrical
circuit.
Odometer and tripmeter modes
Pushing the “SELECT” button switches
the display between the odometer
mode “Odo” and the tripmeter modes
“Trip” in the following order:
Odo → Trip (top) → Trip (bottom) →
Odo
When approximately 2.8 L (0.74 US
gal, 0.62 Imp.gal) of fuel remains in the
fuel tank, the bottom segment of the
fuel meter and fuel level warning indicator will start flashing, and the display will
automatically change to the fuel reserve tripmeter mode “Trip F” and start
counting the distance traveled from that
point. In that case, pushing the
“SELECT” button switches the display
between the various tripmeter and
odometer modes in the following order:
Trip F → Trip (top) → Trip (bottom) →
Odo → Trip F
1
self automatically and the display will
return to the prior mode after refueling
and traveling 5 km (3 mi).
TIP
The display cannot be changed back to
“Trip F” after pushing the “RESET” button.
Fuel meter
With the key in the “ON” position, the
fuel meter indicates the amount of fuel
in the fuel tank. The display segments
of the fuel meter disappear towards “E”
(Empty) as the fuel level decreases.
When the fuel level reaches the bottom
segment near “E”, the fuel level warning indicator and the bottom segment
will flash. Refuel as soon as possible.
2
3
4
5
6
7
1. Fuel reserve tripmeter
To reset a tripmeter, select it by pushing the “SELECT” button until “Trip” or
“Trip F” begins flashing (“Trip” or “Trip
F” will only flash for five seconds).
While “Trip” or “Trip F” is flashing, push
the “RESET” button for at least one
second. If you do not reset the fuel reserve tripmeter manually, it will reset it4-4
Coolant temperature meter
With the key in the “ON” position, the
coolant temperature meter indicates
the temperature of the coolant. The
coolant temperature varies with changes in the weather and engine load. If
the top segment and coolant temperature warning indicator flash, stop the
vehicle and let the engine cool. (See
8
9
INSTRUMENT AND CONTROL FUNCTIONS
page 7-38.)
1
2
3
4
5
6
7
8
9
ECA10021
NOTICE
Do not continue to operate the engine if it is overheating.
Oil change indicator “OIL”
This indicator flashes at the initial 1000
km (600 mi), then at 5000 km (3000 mi)
and every 5000 km (3000 mi) thereafter
to indicate that the engine oil should be
changed.
After changing the engine oil, reset the
oil change indicator. (See page 7-14.)
If the engine oil is changed before the
oil change indicator comes on (i.e. before the periodic oil change interval has
been reached), the indicator must be
reset after the oil change for the next
periodic oil change to be indicated at
the correct time. (See page 7-14.)
The electrical circuit of the indicator can
be checked according to the following
procedure.
1. Set the engine stop switch to “ ”
and turn the key to “ON”.
2. Check that the indicator comes on
for a few seconds and then goes
off.
3. If the indicator does not come on,
have a Yamaha dealer check the
electrical circuit.
TIP
The oil change indicator may flash
when the engine is revved with the
scooter on the centerstand, but this
does not indicate a malfunction.
V-belt replacement indicator
“V-BELT”
This indicator flashes every 20000 km
(12500 mi) when the V-belt needs to be
replaced.
The electrical circuit of the indicator can
be checked according to the following
procedure.
4-5
1. Turn the key to “ON” and make
sure that the engine stop switch is
set to “ ”.
2. If the indicator does not come on,
have a Yamaha dealer check the
electrical circuit.
Self-diagnosis device
This model is equipped with a self-diagnosis device for various electrical circuits.
If a problem is detected in any of those
circuits, the multi-function display will
indicate an error code.
If the multi-function display indicates an
error code, note the code number, and
then have a Yamaha dealer check the
vehicle.
INSTRUMENT AND CONTROL FUNCTIONS
3. Push the “SELECT” button, and
the minute digits will start flashing.
4. Push the “RESET” button to set
the minutes.
5. Push the “SELECT” button and
then release it to start the clock.
Pushing the “SELECT” button for
at least two seconds switches the
clock display to the ambient temperature display.
1
●
will not be displayed.
The accuracy of the temperature
reading may be affected when
riding slowly (approximately under
20 km/h (12.5 mi/h)) or when
stopped at traffic signals, railroad
crossings, etc.
2
3
1. Error code display
ECA11790
NOTICE
If the multi-function display indicates an error code, the vehicle
should be checked as soon as possible in order to avoid engine damage.
Clock mode
To set the clock:
1. Push the “SELECT” button and
“RESET” button together for at
least two seconds.
2. When the hour digits start flashing,
push the “RESET” button to set the
hours.
Ambient temperature display
This display shows the ambient temperature from –10 °C (14 °F) to 50 °C
(122 °F) in 1 °C or 1 °F increments. The
temperature displayed may vary from
the ambient temperature. Pushing the
“SELECT” button for at least two seconds switches the ambient temperature
display to the clock display.
4
TIP
8
●
●
If the ambient temperature falls below –10 °C (14 °F), a lower temperature than –10 °C (14 °F) will
not be displayed.
If the ambient temperature climbs
above 50 °C (122 °F), a higher
temperature than 50 °C (122 °F)
4-6
5
6
7
9
INSTRUMENT AND CONTROL FUNCTIONS
EAU12348
Handlebar switches
Right
EAU12500
Horn switch “
”
Press this switch to sound the horn.
1
Left
EAU12660
1
2
1
2
3
4
5
6
7
8
9
Engine stop switch “ / ”
Set this switch to “ ” before starting
the engine. Set this switch to “ ” to
stop the engine in case of an emergency, such as when the vehicle overturns
or when the throttle cable is stuck.
2
3
1. Dimmer switch “
/
”
2. Turn signal switch “ / ”
3. Horn switch “
”
1. Engine stop switch “
2. Start switch “ ”
/
”
EAU12721
EAU12400
Dimmer switch “ / ”
Set this switch to “ ” for the high
beam and to “ ” for the low beam.
EAU12460
Turn signal switch “ / ”
To signal a right-hand turn, push this
switch to “ ”. To signal a left-hand
turn, push this switch to “ ”. When released, the switch returns to the center
position. To cancel the turn signal
lights, push the switch in after it has returned to the center position.
4-7
Start switch “ ”
With the sidestand up, push this switch
while applying the front or rear brake to
crank the engine with the starter. See
page 6-1 for starting instructions prior
to starting the engine.
INSTRUMENT AND CONTROL FUNCTIONS
EAU12900
Front brake lever
EAU12950
Rear brake lever
EAU12962
Rear brake lock lever
1
1
1
2
3
1. Front brake lever
The front brake lever is located on the
right handlebar grip. To apply the front
brake, pull this lever toward the handlebar grip.
1. Rear brake lever
1. Rear brake lock lever
The rear brake lever is located on the
left handlebar grip. To apply the rear
brake, pull this lever toward the handlebar grip.
This vehicle is equipped with a rear
brake lock lever to prevent the rear
wheel from moving while stopped at
traffic signals, railroad crossings, etc.
5
To lock the rear wheel
Push the rear brake lock lever to the left
until it snaps into place.
7
To unlock the rear wheel
Push the rear brake lock lever back to
the original position.
TIP
●
4-8
4
Be sure to check that the rear
wheel does not move when the
6
8
9
INSTRUMENT AND CONTROL FUNCTIONS
●
1
rear brake lock lever is applied.
To provide secure locking of the
rear wheel, apply the rear brake lever first before moving the rear
brake lock lever to the left.
EWA12361
2
3
4
5
6
7
8
EAU13163
Fuel tank cap
1
To open the fuel tank cap
1. Open the lid by sliding the lever
forward, and then pull the lever up.
WARNING
Never move the rear brake lock lever
to the left while the vehicle is moving, otherwise loss of control or an
accident may result. Make sure that
the vehicle is stopped before moving the rear brake lock lever to the
left.
1
1. Fuel tank cap
2
To install the fuel tank cap
1. Align the match marks, insert the
fuel tank cap into the tank opening,
and then push down on the cap.
1. Lid
2. Opening lever
2. Insert the key into the lock and turn
it clockwise. The lock will be released and the fuel tank cap can
be removed.
9
1
1. Match marks
2. Turn the key counterclockwise to
4-9
INSTRUMENT AND CONTROL FUNCTIONS
the original position, and then remove it.
3. Close the lid.
EWA11121
WARNING
Be sure that the fuel tank cap is
properly installed and locked before
riding the scooter. Leaking fuel is a
fire hazard.
EAU13212
Fuel
Make sure there is sufficient gasoline in
the tank.
EWA10881
WARNING
Gasoline and gasoline vapors are
extremely flammable. To avoid fires
and explosions and to reduce the
risk of injury when refueling, follow
these instructions.
1. Before refueling, turn off the engine and be sure that no one is sitting on the vehicle. Never refuel
while smoking, or while in the vicinity of sparks, open flames, or
other sources of ignition such as
the pilot lights of water heaters and
clothes dryers.
2. Do not overfill the fuel tank. Stop
filling when the fuel reaches the
bottom of the filler tube. Because
fuel expands when it heats up,
heat from the engine or the sun
can cause fuel to spill out of the
fuel tank.
4-10
1
2
2
3
1. Fuel tank filler tube
2. Fuel level
4
3. Wipe up any spilled fuel immediately. NOTICE: Immediately wipe
off spilled fuel with a clean, dry,
soft cloth, since fuel may deteriorate painted surfaces or plastic
parts.[ECA10071]
4. Be sure to securely close the fuel
tank cap.
EWA15151
WARNING
Gasoline is poisonous and can
cause injury or death. Handle gasoline with care. Never siphon gasoline by mouth. If you should swallow
some gasoline or inhale a lot of gasoline vapor, or get some gasoline in
5
6
7
8
9
INSTRUMENT AND CONTROL FUNCTIONS
1
2
3
4
5
6
7
8
9
your eyes, see your doctor immediately. If gasoline spills on your skin,
wash with soap and water. If gasoline spills on your clothing, change
your clothes.
EAU36081
Recommended fuel
UNLEADED GASOLINE ONLY
Fuel tank capacity:
14.0 L (3.70 US gal, 3.08 Imp.gal)
will extend spark plug life and reduce
maintenance costs.
Gasohol
There are two types of gasohol: gasohol containing ethanol and that containing methanol. Gasohol containing
ethanol can be used if the ethanol content does not exceed 10% (E10). Gasohol containing methanol is not
recommended by Yamaha because it
can cause damage to the fuel system
or vehicle performance problems.
ECA11400
NOTICE
Use only unleaded gasoline. The use
of leaded gasoline will cause severe
damage to internal engine parts,
such as the valves and piston rings,
as well as to the exhaust system.
Your Yamaha engine has been designed to use regular unleaded gasoline with a pump octane number
[(R+M)/2] of 86 or higher, or a research
octane number of 91 or higher. If
knocking (or pinging) occurs, use a
gasoline of a different brand or premium unleaded fuel. Use of unleaded fuel
EAU13433
Catalytic converter
This model is equipped with a catalytic
converter in the exhaust system.
EWA10862
WARNING
The exhaust system is hot after operation. To prevent a fire hazard or
burns:
● Do not park the vehicle near
possible fire hazards such as
grass or other materials that
easily burn.
● Park the vehicle in a place
where pedestrians or children
are not likely to touch the hot
exhaust system.
● Make sure that the exhaust system has cooled down before doing any maintenance work.
● Do not allow the engine to idle
more than a few minutes. Long
idling can cause a build-up of
heat.
ECA10701
NOTICE
Use only unleaded gasoline. The use
of leaded gasoline will cause unre4-11
INSTRUMENT AND CONTROL FUNCTIONS
pairable damage to the catalytic
converter.
EAU34140
Seats
1
1
2
2
3
1. Open.
TIP
Do not push inward when turning the
key.
1. Rider seat
2. Passenger seat
Rider seat
3. Fold the rider seat up.
To open the rider seat
1. Place the scooter on the centerstand.
2. Insert the key into the main switch,
and then turn it counterclockwise.
1
4
5
6
7
8
9
1. Rider seat
4-12
INSTRUMENT AND CONTROL FUNCTIONS
1
To close the rider seat
1. Fold the rider seat down, and then
push it down to lock it in place.
2. Remove the key from the main
switch if the scooter will be left unattended.
3
TIP
Make sure that the rider seat is properly
secured before riding.
4
Passenger seat
2
5
6
7
To install the passenger seat
1. Insert the projections on the passenger seat into the holders as
shown, place the passenger seat
in the original position, and then install the bolt.
EAU34150
Adjusting the rider seat
1
1
2
1. Rider seat
To remove the passenger seat
1. Open the rider seat.
2. Remove the bolt, and then pull the
passenger seat forward.
1
2
The rider seat can be adjusted as follows to change the riding position.
1. Open the rider seat. (See
page 4-12.)
2. Remove the bolts.
2
1. Passenger seat
2. Seat holder
2. Close the rider seat.
TIP
Make sure that the passenger seat is
properly secured before riding.
8
9
1. Passenger seat
2. Bolt
4-13
INSTRUMENT AND CONTROL FUNCTIONS
EAU14494
Storage compartments
and then remove it.
1
1
1
1. Bolt
3. Slide the rider seat forward or
backward to the desired position.
4. Install bolts and securely tighten
them.
5. Close the rider seat.
Front storage compartment A
To open the storage compartment
when it is locked, insert the key in the
lock, turn it counterclockwise, and then
grasp the lock while pushing the button
in.
To open the storage compartment
when it is unlocked, simply grasp the
lock while pushing the button in.
2
2
1. Lock.
2. Lid
1
2
Front storage compartment B
To open the storage compartment,
slide the lever up, and then pull on the
lever.
3
4
5
6
7
3
1. Open.
2. Button
3. Lid
8
9
To lock the storage compartment, push
the lid into the original position, insert
the key in the lock, turn it clockwise,
4-14
INSTRUMENT AND CONTROL FUNCTIONS
1
●
1
1
2
3
4
5
6
7
8
9
being washed, wrap any articles
stored in the compartment in a
plastic bag.
Do not keep anything valuable
or breakable in the storage compartment.
ECA11100
2
1. Storage compartment opening lever
2. Lid
To close the storage compartment,
push the lid into the original position.
WARNING! Do not store heavy items
in this compartment.[EWA11161]
Rear storage compartment
Two helmets can be stored in the storage compartment under the seats.
(See page 4-12.)
1. Rider seat
ECA10080
NOTICE
Keep the following points in mind
when using the storage compartment.
● Since the storage compartment
accumulates heat when exposed to the sun, do not store
anything susceptible to heat inside it.
● To avoid humidity from spreading through the storage compartment, wrap wet articles in a
plastic bag before storing them
in the compartment.
● Since the storage compartment
may get wet while the scooter is
4-15
NOTICE
Do not leave the rider seat open for
an extended period of time, otherwise the light may cause the battery
to discharge.
EWA11171
WARNING
Do not exceed the following loading
limits:
● Front storage compartment A: 2
kg (4 lb)
● Rear storage compartment: 5 kg
(11 lb)
● Maximum load for the vehicle:
196 kg (432 lb)
INSTRUMENT AND CONTROL FUNCTIONS
EAU14891
Adjusting the shock absorber
assemblies
1
(b)
2
5
4
3
2
1
(a)
3
1. Spring preload adjusting ring
2. Position indicator
3. Spring preload adjusting tool
Each shock absorber assembly is
equipped with a spring preload adjusting ring.
ECA10101
NOTICE
To avoid damaging the mechanism,
do not attempt to turn beyond the
maximum or minimum settings.
handling and loss of stability may
result.
Adjust the spring preload as follows.
To increase the spring preload and
thereby harden the suspension, turn
the adjusting ring on each shock absorber assembly in direction (a). To decrease the spring preload and thereby
soften the suspension, turn the adjusting ring on each shock absorber assembly in direction (b).
● Align the appropriate notch in the
adjusting ring with the position indicator on the shock absorber.
● Use the spring preload adjusting
tool included in the owner’s tool kit
to make this adjustment.
Spring preload setting:
Minimum (soft):
1
Standard:
2
Maximum (hard):
5
EWA10210
WARNING
Always adjust both shock absorber
assemblies equally, otherwise poor
4-16
EAU15301
Sidestand
The sidestand is located on the left side
of the frame. Raise the sidestand or
lower it with your foot while holding the
vehicle upright.
TIP
The built-in sidestand switch is part of
the ignition circuit cut-off system, which
cuts the ignition in certain situations.
(See further down for an explanation of
the ignition circuit cut-off system.)
2
3
4
EWA10240
WARNING
The vehicle must not be ridden with
the sidestand down, or if the sidestand cannot be properly moved up
(or does not stay up), otherwise the
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
Yamaha’s ignition circuit cut-off
system has been designed to assist
the operator in fulfilling the responsibility of raising the sidestand before starting off. Therefore, check
this system regularly as described
below and have a Yamaha dealer re-
5
6
7
8
9
INSTRUMENT AND CONTROL FUNCTIONS
pair it if it does not function properly.
1
2
3
4
5
6
EAU45051
Ignition circuit cut-off system
The ignition circuit cut-off system (comprising the sidestand switch and brake
light switches) has the following functions.
● It prevents starting when the sidestand is up, but neither brake is applied.
● It prevents starting when either
brake is applied, but the sidestand
is still down.
● It cuts the running engine when the
sidestand is moved down.
Periodically check the operation of the
ignition circuit cut-off system according
to the following procedure.
7
8
9
4-17
INSTRUMENT AND CONTROL FUNCTIONS
WARNING
With the engine turned off:
1. Move the sidestand down.
2. Make sure that the engine stop switch is turned on.
3. Turn the key on.
4. Keep the front or rear brake applied.
5. Push the start switch.
Does the engine start?
NO
If a malfunction is noted, have a Yamaha
dealer check the system before riding.
2
The sidestand switch may not be working correctly.
The scooter should not be ridden until
checked by a Yamaha dealer.
YES
With the engine still off:
6. Move the sidestand up.
7. Keep the front or rear brake applied.
8. Push the start switch.
Does the engine start?
YES
4
5
The brake switch may not be working correctly.
The scooter should not be ridden until
checked by a Yamaha dealer.
NO
6
7
With the engine still running:
9. Move the sidestand down.
Does the engine stall?
YES
3
The sidestand switch may not be working correctly.
The scooter should not be ridden until
checked by a Yamaha dealer.
NO
The system is OK. The scooter can be ridden.
4-18
8
9
FOR YOUR SAFETY – PRE-OPERATION CHECKS
EAU15596
Inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the inspection
and maintenance procedures and schedules described in the Owner’s Manual.
1
2
3
EWA11151
WARNING
Failure to inspect or maintain the vehicle properly increases the possibility of an accident or equipment damage.
Do not operate the vehicle if you find any problem. If a problem cannot be corrected by the procedures provided in
this manual, have the vehicle inspected by a Yamaha dealer.
Before using this vehicle, check the following points:
ITEM
4
CHECKS
●
Fuel
●
●
5
●
Engine oil
6
●
●
Final transmission oil
●
●
7
Coolant
●
●
●
8
●
●
Front brake
9
●
●
●
●
Check fuel level in fuel tank.
Refuel if necessary.
Check fuel line for leakage.
Check oil level in engine.
If necessary, add recommended oil to specified level.
Check vehicle for oil leakage.
Check vehicle for oil leakage.
Check coolant level in reservoir.
If necessary, add recommended coolant to specified level.
Check cooling system for leakage.
Check operation.
If soft or spongy, have Yamaha dealer bleed hydraulic system.
Check brake pads for wear.
Replace if necessary.
Check fluid level in reservoir.
If necessary, add recommended brake fluid to specified level.
Check hydraulic system for leakage.
5-1
PAGE
4-10
7-14
7-17
7-18
7-25, 7-26, 7-27
FOR YOUR SAFETY – PRE-OPERATION CHECKS
ITEM
CHECKS
●
●
●
Rear brake
●
●
●
●
●
Throttle grip
●
●
●
Wheels and tires
●
●
●
Brake levers
Centerstand, sidestand
Chassis fasteners
Instruments, lights, signals
and switches
Sidestand switch
●
●
●
●
●
●
●
●
●
●
Check operation.
If soft or spongy, have Yamaha dealer bleed hydraulic system.
Check brake pads for wear.
Replace if necessary.
Check fluid level in reservoir.
If necessary, add recommended brake fluid to specified level.
Check hydraulic system for leakage.
Make sure that operation is smooth.
Check cable free play.
If necessary, have Yamaha dealer adjust cable free play and lubricate cable and
grip housing.
Check for damage.
Check tire condition and tread depth.
Check air pressure.
Correct if necessary.
Make sure that operation is smooth.
Lubricate lever pivoting points if necessary.
Make sure that operation is smooth.
Lubricate pivots if necessary.
Make sure that all nuts, bolts and screws are properly tightened.
Tighten if necessary.
Check operation.
Correct if necessary.
Check operation of ignition circuit cut-off system.
If system is not working correctly, have Yamaha dealer check vehicle.
PAGE
7-25, 7-26, 7-27
2
7-22, 7-29
3
7-23, 7-24
4
7-29
5
7-29
6
—
—
4-16
7
8
9
5-2
OPERATION AND IMPORTANT RIDING POINTS
EAU15951
EAU48020
EAU45952
Starting the engine
1
Read the Owner’s Manual carefully to
become familiar with all controls. If
there is a control or function you do not
understand, ask your Yamaha dealer.
EWA10271
2
3
4
WARNING
Failure to familiarize yourself with
the controls can lead to loss of control, which could cause an accident
or injury.
TIP
This model is equipped with a lean angle sensor to stop the engine in case of
a turnover. In this case, the multi-function display indicates error code 30, but
this is not a malfunction. Turn the key to
“OFF” and then to “ON” to clear the error code. Failing to do so will prevent
the engine from starting even though
the engine will crank when pushing the
start switch.
5
6
7
8
ECA10250
NOTICE
See page 6-3 for engine break-in instructions prior to operating the vehicle for the first time.
In order for the ignition circuit cut-off
system to enable starting, the sidestand must be up.
See page 4-17 for more information.
1. Turn the key to “ON” and make
sure that the engine stop switch is
set to “ ”.
The following warning light, indicator light and indicators should
come on for a few seconds, then
go off.
● Engine trouble warning light
● V-belt replacement indicator
● Oil change indicator
ECA15022
NOTICE
If a warning light, indicator light or
indicator does not go off, see pages
4-2, 4-5 or 4-3 for the corresponding
warning light, indicator light or indicator circuit check.
9
6-1
OPERATION AND IMPORTANT RIDING POINTS
2. Close the throttle completely.
3. Start the engine by pushing the
start switch while applying the front
or rear brake. NOTICE: For maximum engine life, never accelerate hard when the engine is
cold![ECA11041]
If the engine does not start, release the start switch, wait a few
seconds, and then try again. Each
starting attempt should be as short
as possible to preserve the battery. Do not crank the engine more
than 10 seconds on any one attempt.
EAU45091
Starting off
EAU16780
Acceleration and deceleration
1. While pulling the rear brake lever
with your left hand and holding the
grab bar with your right hand, push
the scooter off the centerstand.
(b)
2
1
3
(a)
The speed can be adjusted by opening
and closing the throttle. To increase the
speed, turn the throttle grip in direction
(a). To reduce the speed, turn the throttle grip in direction (b).
1. Grab bar
2. Sit astride the seat, and then adjust the rear view mirrors.
3. Switch the turn signals on.
4. Check for oncoming traffic, and
then slowly turn the throttle grip (on
the right) in order to take off.
5. Switch the turn signals off.
6-2
4
5
6
7
8
9
OPERATION AND IMPORTANT RIDING POINTS
EAU16793
Braking
Front
EAU16841
Engine break-in
There is never a more important period
in the life of your engine than the period
between 0 and 1600 km (1000 mi). For
this reason, you should read the following material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1600 km (1000 mi). The various parts in
the engine wear and polish themselves
to the correct operating clearances.
During this period, prolonged full-throttle operation or any condition that might
result in engine overheating must be
avoided.
EWA10300
1
●
2
●
3
4
5
6
7
8
9
●
●
WARNING
Avoid braking hard or suddenly
(especially when leaning over to
one side), otherwise the scooter
may skid or overturn.
Railroad crossings, streetcar
rails, iron plates on road construction sites, and manhole
covers become extremely slippery when wet. Therefore, slow
down when approaching such
areas and cross them with caution.
Keep in mind that braking on a
wet road is much more difficult.
Ride slowly down a hill, as braking downhill can be very difficult.
Rear
EAU34321
0–1000 km (0–600 mi)
Avoid prolonged operation above 4000
r/min. NOTICE: After 1000 km (600
mi) of operation, be sure to replace
the engine oil, final transmission oil
and the oil filter element.[ECA12931]
1. Close the throttle completely.
2. Apply both front and rear brakes
simultaneously while gradually increasing the pressure.
1000–1600 km (600–1000 mi)
Avoid prolonged operation above 6000
r/min.
6-3
OPERATION AND IMPORTANT RIDING POINTS
1600 km (1000 mi) and beyond
The vehicle can now be operated normally.
ECA10310
NOTICE
● Keep the engine speed out of
the tachometer red zone.
● If any engine trouble should occur during the engine break-in
period, immediately have a
Yamaha dealer check the vehicle.
EAU17213
Parking
When parking, stop the engine, and
then remove the key from the main
switch.
EWA10311
●
●
●
WARNING
Since the engine and exhaust
system can become very hot,
park in a place where pedestrians or children are not likely to
touch them and be burned.
Do not park on a slope or on soft
ground, otherwise the vehicle
may overturn, increasing the
risk of a fuel leak and fire.
Do not park near grass or other
flammable materials which
might catch fire.
2
3
4
5
6
7
8
9
6-4
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU17232
1
2
3
Periodic inspection, adjustment, and lubrication will keep your vehicle in the
safest and most efficient condition possible. Safety is an obligation of the vehicle owner/operator. The most important
points of vehicle inspection, adjustment, and lubrication are explained on
the following pages.
●
parts that can cause shocks or
fires.
Running the engine while servicing can lead to eye injury,
burns, fire, or carbon monoxide
poisoning – possibly leading to
death. See page 2-1 for more information about carbon monoxide.
EWA10321
4
5
6
7
8
9
WARNING
Failure to properly maintain the vehicle or performing maintenance activities incorrectly may increase
your risk of injury or death during
service or while using the vehicle. If
you are not familiar with vehicle service, have a Yamaha dealer perform
service.
EWA15121
WARNING
Turn off the engine when performing
maintenance
unless
otherwise
specified.
● A running engine has moving
parts that can catch on body
parts or clothing and electrical
7-1
EAU17302
Emission controls not only function to
ensure cleaner air, but are also vital to
proper engine operation and maximum
performance. In the following periodic
maintenance charts, the services related to emissions control are grouped
separately. These services require
specialized data, knowledge, and
equipment. Maintenance, replacement,
or repair of the emission control devices and systems may be performed by
any repair establishment or individual
that is certified (if applicable). Yamaha
dealers are trained and equipped to
perform these particular services.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU17502
Owner’s tool kit
TIP
If you do not have the tools or experience required for a particular job, have
a Yamaha dealer perform it for you.
1
2
3
2
4
1. Storage compartment mat
2. Owner’s tool kit
5
The owner’s tool kit is located inside the
rear storage compartment. (See
page 4-14.)
Pull up the storage compartment mat,
and then remove the owner’s tool kit.
The service information included in this
manual and the tools provided in the
owner’s tool kit are intended to assist
you in the performance of preventive
maintenance and minor repairs. However, additional tools such as a torque
wrench may be necessary to perform
certain maintenance work correctly.
6
7
8
9
7-2
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU17600
Periodic maintenance chart for the emission control system
INITIAL
1
No.
ITEM
ROUTINE
2
●
3
1 *
Fuel line
●
●
4
2
Spark plug
5
3 *
Valve clearance
6
4 *
Crankcasebreather
system
5 *
7
6 *
8
7 *
9
Fuel injection
Evaporative emission control system
Air induction system
●
●
●
●
●
●
●
●
●
●
Check fuel and vacuum hoses
for cracks or damage.
Replace if necessary.
Check condition.
Adjust gap and clean.
Replace every 10000 mi (16000
km) or 18 months.
Check and adjust valve
clearance when engine is cold.
Check breather hose for cracks
or damage.
Replace if necessary.
Check engine idle speed.
Check control system for
damage.
Replace if necessary.
Check the air cut-off valve, reed
valve, and hose for damage.
Replace any damaged parts.
600 mi
(1000 km)
or
1 month
ODOMETER READINGS
4000 mi
(7000 km)
or
6 months
8000 mi
(13000
km)
or
12 months
12000 mi
(19000
km)
or
18 months
16000 mi
(25000
km)
or
24 months
20000 mi
(31000
km)
or
30 months
√
√
√
√
√
√
√
Replace.
√
√
Every 26600 mi (42000 km)
√
√
√
√
√
√
√
√
√
√
√
√
√
* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.
7-3
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU32185
General maintenance and lubrication chart
INITIAL
No.
1
2
ITEM
Air filter elements
V-belt case air filter
element
3 *
Front brake
4 *
Rear brake
ROUTINE
●
Replace.
●
Clean.
●
Check operation, fluid level, and
for fluid leakage.
Replace brake pads if
necessary.
Check operation, fluid level, and
for fluid leakage.
Replace brake pads if
necessary.
Check for cracks or damage.
Replace.
Check operation.
Adjust.
Check runout and for damage.
Replace if necessary.
Check tread depth and for
damage.
Replace if necessary.
Check air pressure.
Correct if necessary.
Check bearings for smooth
operation.
Replace if necessary.
●
●
5 *
Brake hoses
●
●
●
6
Rear brake lock
7 *
Wheels
●
●
●
●
●
8 *
Tires
●
●
●
●
9 *
Wheel bearings
●
600 mi
(1000 km)
or
1 month
ODOMETER READINGS
4000 mi
(7000 km)
or
6 months
8000 mi
(13000
km)
or
12 months
12000 mi
(19000
km)
or
18 months
16000 mi
(25000
km)
or
24 months
20000 mi
(31000
km)
or
30 months
2
Every 12000 mi (19000 km)
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
Every 4 years
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
3
4
5
6
√
7-4
7
8
9
PERIODIC MAINTENANCE AND ADJUSTMENT
INITIAL
No.
ITEM
ROUTINE
1
●
Check bearing assemblies for
looseness.
Moderately repack with
lithium-soap-based grease.
Check all chassis fitting and
fasteners.
Correct if necessary.
●
●
2
10 *
Steering bearings
●
3
●
11 *
4
12
5
13
6
14
Centerstand and
sidestand pivots
7
15 *
Sidestand switch
9
16 *
16000 mi
(25000
km)
or
24 months
20000 mi
(31000
km)
or
30 months
√
√
√
√
√
√
Every 12000 mi (19000 km)
√
Apply silicone grease lightly.
√
√
√
√
√
●
Apply silicone grease lightly.
√
√
√
√
√
●
Check operation.
Apply lithium-soap-based
grease lightly.
Check operation and replace if
necessary.
Check operation and for oil
leakage.
Replace if necessary.
Check operation and for oil
leakage.
Replace if necessary.
Change. (See pages 4-3 and
7-14.)
Check oil level and vehicle for oil
leakage.
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
●
●
●
●
●
18
12000 mi
(19000
km)
or
18 months
√
Front fork
Shock absorber
assemblies
8000 mi
(13000
km)
or
12 months
√
●
17 *
4000 mi
(7000 km)
or
6 months
√
●
8
600 mi
(1000 km)
or
1 month
√
Chassis fasteners
Front brake lever
pivot shaft
Rear brake lever
pivot shaft
ODOMETER READINGS
Engine oil
●
√
√
When the oil change indicator flashes (every 3125 mi (5000 km))
√
Every 3125 mi (5000 km)
7-5
PERIODIC MAINTENANCE AND ADJUSTMENT
INITIAL
No.
ITEM
19
Engine oil filter element
20 *
Cooling system
ROUTINE
●
Replace.
●
●
Check coolant level and vehicle
for coolant leakage.
Change.
Check vehicle for oil leakage.
Change.
Replace.
●
Check operation.
●
21
22 *
23 *
Final transmission
oil
V-belt
Front and rear
brake switches
●
●
600 mi
(1000 km)
or
1 month
ODOMETER READINGS
4000 mi
(7000 km)
or
6 months
√
8000 mi
(13000
km)
or
12 months
12000 mi
(19000
km)
or
18 months
16000 mi
(25000
km)
or
24 months
20000 mi
(31000
km)
or
30 months
2
Every 12500 mi (20000 km)
√
√
√
√
√
Every 3 years
√
√
√
3
4
When the V-belt replacement indicator flashes (every 12500 mi (20000 km)).
√
√
√
Check operation and free play.
● Adjust the throttle cable free
Throttle grip hous√
√
24 *
play if necessary.
ing and cable
● Lubricate the throttle grip
housing and cable.
Lights, signals and
● Check operation.
25 *
√
√
√
switches
● Adjust headlight beam.
* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.
√
√
√
5
√
√
√
6
√
√
√
●
TIP
From 24000 mi (37000 km) or 36 months, repeat the maintenance intervals starting from 8000 mi (13000 km) or 12 months.
7-6
7
8
9
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU36372
TIP
●
1
●
●
2
3
4
5
Engine air filters and V-belt air filter
This model’s engine air filters are equipped with disposable oil-coated paper elements, which must not be cleaned
with compressed air to avoid damaging them.
The engine air filter elements need to be replaced and the V-belt air filter element needs to be serviced more frequently when riding in unusually wet or dusty areas.
Hydraulic brake service
After disassembling the brake master cylinders and calipers, always change the fluid. Regularly check the brake fluid
levels and fill the reservoirs as required.
Every two years replace the internal components of the brake master cylinders and calipers, and change the brake
fluid.
Replace the brake hoses every four years and if cracked or damaged.
●
●
●
●
6
7
8
9
7-7
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU18712
Removing and installing
cowlings and panels
1
1
The cowlings and panels shown need
to be removed to perform some of the
maintenance jobs described in this
chapter. Refer to this section each time
a cowling or panel needs to be removed and installed.
2
1
3 4
2
2
3
1. Cowling D
1. Quick fastener
2. Cowling A
4
EAU34282
Cowling A
6
1.
2.
3.
4.
5.
6.
Panel A
Cowling C
Cowling A
Cowling B
Panel B
Cowling E
5
To remove the cowling
1. Open the rider seat. (See
page 4-12.)
2. Remove the quick fasteners in the
rear storage compartment, and
then pull the cowling off as shown.
TIP
The quick fastener is removed by pushing the center pin in with a screwdriver,
and then pulling the fastener out.
7-8
To install the cowling
1. Place the cowling in the original
position, and then install the quick
fasteners.
TIP
To install the quick fastener, push the
center pin out so that it will protrude
from the fastener head, insert the fastener into the cowling, and then push
the protruding pin in until it is flush with
the fastener head.
2. Close the rider seat.
5
6
7
8
9
PERIODIC MAINTENANCE AND ADJUSTMENT
To install the cowling
Place the cowling in the original position, and then install the screws.
Cowling B
To remove the cowling
1. Remove the screws.
1
1
2
3
4
5
6
1
Cowlings C and D
To remove one of the cowlings
1. Remove cowlings A and B.
2. Remove the passenger seat. (See
page 4-12.)
3. Remove the grab bar by removing
the grab bar bolts and collars.
2
1
2
1. Cowling B
2. Screw
1
1
2
2
3
1. Screw access cover
5. Remove the screws, and then pull
the cowling off.
1
2. Remove the cowling as shown.
1
2
7
8
1
9
1
1. Grab bar bolt
2. Collar
3. Grab bar
1. Screw
4. Remove the screw access cover
by pulling it off.
1. Cowling B
7-9
To install the cowling
1. Place the cowling in the original position, and then install the screws.
PERIODIC MAINTENANCE AND ADJUSTMENT
2
1
1
2. Install the screw access cover by
placing it in its original position.
3. Install the grab bar by installing the
collars and grab bar bolts.
3
1. Left floorboard mat
2. Remove the cowling screws.
Tightening torque:
Grab bar bolt:
23 Nm (2.3 m·kgf, 16.6 ft·lbf)
1. Cowling E
4
To install the cowling
1. Insert the projections on the cowling into the slots as shown, and
then install the screws.
6
4. Install the passenger seat.
5. Install cowlings A and B.
7
1
Cowling E
To remove the cowling
1. Pull up the left floorboard mats as
shown.
5
8
1. Screw
9
3. Pull the cowling down slightly, and
then pull it outward as shown.
1
1
1. Projection
2. Place the left floorboard mats in
the original position.
7-10
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU34290
1
Panel A
1
2
To remove the panel
1. Remove the bolts.
2
2
3
To install the panel
Place the panel in the original position,
and then install the bolts.
4
5
1
1. Panel B
2. Screw
To install the panel
Place the panel in the original position,
and then install the screws.
6
7
1. Bolt
2. Panel A
2
2. Pull the panel out as shown.
8
9
Panel B
1
To remove the panel
Remove the screws, and then pull the
panel outward.
7-11
1. Screw
2. Panel B
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU34172
Checking the spark plug
The spark plug is an important engine
component, which is easy to check.
Since heat and deposits will cause any
spark plug to slowly erode, the spark
plug should be removed and checked
in accordance with the periodic maintenance and lubrication chart. In addition,
the condition of the spark plug can reveal the condition of the engine.
To remove the spark plug
1. Open the rider seat. (See
page 4-12.)
2. Pull up the storage compartment
mat, and then remove the spark
plug cover by removing the
screws.
2
1
3
1
2
3
1. Storage compartment mat
2. Spark plug cover
3. Screw
3. Remove the spark plug cap.
1. Spark plug wrench
4
To check the spark plug
1. Check that the porcelain insulator
around the center electrode of the
spark plug is a medium-to-light tan
(the ideal color when the vehicle is
ridden normally).
TIP
If the spark plug shows a distinctly different color, the engine could be operating improperly. Do not attempt to
diagnose such problems yourself. Instead, have a Yamaha dealer check
the vehicle.
1
1. Spark plug cap
4. Remove the spark plug as shown,
with the spark plug wrench included in the owner’s tool kit.
7-12
2. Check the spark plug for electrode erosion and excessive carbon or other deposits, and replace
5
6
7
8
9
PERIODIC MAINTENANCE AND ADJUSTMENT
it if necessary.
Specified spark plug:
NGK/CR7E
1
2
3
To install the spark plug
1. Measure the spark plug gap with a
wire thickness gauge and, if necessary, adjust the gap to specification.
4
5
6
1
7
3. Install the spark plug with the
spark plug wrench, and then tighten it to the specified torque.
Tightening torque:
Spark plug:
12.5 Nm (1.25 m·kgf, 9 ft·lbf)
TIP
If a torque wrench is not available when
installing a spark plug, a good estimate
of the correct torque is 1/4–1/2 turn
past finger tight. However, the spark
plug should be tightened to the specified torque as soon as possible.
4. Install the spark plug cap.
TIP
Make sure the spark plug wire is fastened in the clamp as shown.
1. Spark plug gap
8
9
1
Spark plug gap:
0.7–0.8 mm (0.028–0.031 in)
2. Clean the surface of the spark plug
gasket and its mating surface, and
then wipe off any grime from the
spark plug threads.
7-13
2
1. Spark plug cap
2. Spark plug wire clamp
5. Install the spark plug cover by installing the screws.
6. Place the storage compartment
mat in the original position.
7. Close the rider seat.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU36110
Canister
EAU34184
Engine oil and oil filter
element
The engine oil level should be checked
before each ride. In addition, the oil
must be changed and the oil filter element replaced at the intervals specified
in the periodic maintenance and lubrication chart and when the oil change indicator comes on.
This model is equipped with a canister
to prevent the discharging of fuel vapor
into the atmosphere. Before operating
this vehicle, make sure to check the following:
● Check each hose connection.
● Check each hose and canister for
cracks or damage. Replace if
damaged.
● Make sure that the canister breather is not blocked, and if necessary,
clean it.
To check the engine oil level
1. Place the vehicle on the centerstand. A slight tilt to the side can
result in a false reading.
2. Start the engine, warm it up for
several minutes, and then turn it
off.
3. Wait a few minutes until the oil settles, remove the oil filler cap, wipe
the dipstick clean, insert it back
into the oil filler hole (without
screwing it in), and then remove it
again to check the oil level.
TIP
The engine oil should be between the
minimum and maximum level marks.
7-14
1
1
2
3
1. Engine oil filler cap
2. Maximum level mark
3. Minimum level mark
4. If the engine oil is below the minimum level mark, add sufficient oil
of the recommended type to raise
it to the correct level.
5. Insert the dipstick into the oil filler
hole, and then tighten the oil filler
cap.
2
3
4
5
6
7
8
To change the engine oil (with or
without oil filter element replacement)
1. Start the engine, warm it up for
several minutes, and then turn it
off.
2. Place an oil pan under the engine
9
PERIODIC MAINTENANCE AND ADJUSTMENT
to collect the used oil.
3. Remove the engine oil filler cap
and the engine oil drain bolt to
drain the oil from the crankcase.
1
2
1
1
1
2
2
3
1. Engine oil drain bolt
2. Washer
4
5
6
7
8
9
1. Engine oil drain bolt
4. Check the washer for damage and
replace it if necessary.
TIP
Skip steps 5–7 if the oil filter element is
not being replaced.
1. Bolt
2. Oil filter element cover
6. Remove and replace the oil filter
element and O-rings.
1
5. Remove the oil filter element cover
by removing the bolts. NOTICE:
When removing the oil filter element cover, the compression
spring will fall out. Take care not
to lose the compression
spring.[ECA12911]
3 4
1.
2.
3.
4.
7-15
2
Oil filter element cover
O-ring
Compression spring
Oil filter element
PERIODIC MAINTENANCE AND ADJUSTMENT
7. Install the compression spring and
oil filter element cover by installing
the bolts, then tightening them to
the specified torque.
Tightening torque:
Oil filter element cover bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
TIP
Make sure that the O-rings are properly
seated.
8. Install the washer and the engine
oil drain bolt, and then tighten the
drain bolt to the specified torque.
Tightening torque:
Engine oil drain bolt:
20 Nm (2.0 m·kgf, 14.5 ft·lbf)
TIP
Make sure that the washer is properly
seated.
9. Refill with the specified amount of
the recommended engine oil, and
then install and tighten the oil filler
cap.
Recommended engine oil:
See page 9-1.
Oil quantity:
Without oil filter element replacement:
1.50 L (1.59 US qt, 1.32 Imp.qt)
With oil filter element replacement:
1.70 L (1.80 US qt, 1.50 Imp.qt)
11. Reset the oil change indicator according to the following procedure.
To reset the oil change indicator
1. Turn the key to “ON”.
2. Hold the “OIL CHANGE” button
pushed for two to eight seconds.
TIP
Be sure to wipe off spilled oil on any
parts after the engine and exhaust system have cooled down.
2
3
4
ECA11670
NOTICE
● Do not use oils with a diesel
specification of “CD” or oils of a
higher quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
● Be sure no foreign material enters the crankcase.
10. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking, immediately turn the engine off and
check for the cause.
7-16
5
1
6
1. “OIL CHANGE” button
3. Release the “OIL CHANGE” button, and the oil change indicator
will go off.
TIP
If the engine oil is changed before the
oil change indicator comes on (i.e. before the periodic oil change interval has
been reached), the indicator must be
reset after the oil change for the next
periodic oil change to be indicated at
7
8
9
PERIODIC MAINTENANCE AND ADJUSTMENT
1
2
3
4
5
6
7
8
the correct time. To reset the oil change
indicator before the periodic oil change
interval has been reached, follow the
above procedure, but note that the indicator will come on for 1.4 seconds after
releasing the “OIL CHANGE” button,
otherwise repeat the procedure.
EAU20064
Final transmission oil
The final transmission case must be
checked for oil leakage before each
ride. If any leakage is found, have a
Yamaha dealer check and repair the
scooter. In addition, the final transmission oil must be changed as follows at
the intervals specified in the periodic
maintenance and lubrication chart.
1. Start the engine, warm up the final
transmission oil by riding the
scooter for several minutes, and
then stop the engine.
2. Place the scooter on the centerstand.
3. Place an oil pan under the final
transmission case to collect the
used oil.
4. Remove the final transmission oil
filler cap and final transmission
drain bolt to drain the oil from the final transmission case.
9
7-17
1
2
1. Final transmission oil filler cap
2. Final transmission oil drain bolt
5. Install the final transmission oil
drain bolt, and then tighten it to the
specified torque.
Tightening torque:
Final transmission oil drain bolt:
20 Nm (2.0 m·kgf, 14.5 ft·lbf)
6. Refill with the specified amount of
the recommended final transmission oil, and then install and tighten
the oil filler cap. WARNING! Make
sure that no foreign material enters the final transmission case.
Make sure that no oil gets on the
tire or wheel.[EWA11311]
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU20070
Recommended final transmission
oil:
See page 9-1.
Oil quantity:
0.25 L (0.26 US qt, 0.22 Imp.qt)
7. Check the final transmission case
for oil leakage. If oil is leaking,
check for the cause.
Coolant
1
The coolant level should be checked
before each ride. In addition, the coolant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.
2
EAU34193
To check the coolant level
1. Place the vehicle on a level surface and hold it in an upright position.
TIP
●
●
The coolant level must be checked
on a cold engine since the level
varies with engine temperature.
Make sure that the vehicle is positioned straight up when checking
the coolant level. A slight tilt to the
side can result in a false reading.
3
1. Right floorboard mat
3. Remove the coolant reservoir cover by removing the screw.
5
2
1
6
7
8
2. Pull up the right floorboard mat as
shown.
1. Screw
2. Coolant reservoir cover
4. Check the coolant level in the coolant reservoir.
7-18
4
9
PERIODIC MAINTENANCE AND ADJUSTMENT
TIP
The coolant should be between the
minimum and maximum level marks.
1
2
3
4
5
6
7
8
9
5. If the coolant is at or below the
minimum level mark, open the
coolant reservoir cap, add coolant
to the maximum level mark, and
then close the coolant reservoir
cap. WARNING! Remove only
the coolant reservoir cap. Never
attempt to remove the radiator
cap when the engine is
hot.[EWA15161] NOTICE: If coolant is
not available, use distilled water
or soft tap water instead. Do not
use hard water or salt water
since it is harmful to the engine.
If water has been used instead
of coolant, replace it with coolant as soon as possible, otherwise the cooling system will not
be protected against frost and
corrosion. If water has been
added to the coolant, have a
Yamaha dealer check the antifreeze content of the coolant as
soon as possible, otherwise the
effectiveness of the coolant will
be reduced.[ECA10472]
1
EAU34206
2
3
1. Minimum level mark
2. Maximum level mark
3. Coolant reservoir cap
Coolant reservoir capacity (up to the
maximum level mark):
0.32 L (0.34 US qt, 0.28 Imp.qt)
6. Install the coolant reservoir cover
by installing the screw.
7. Place the right floorboard mat in
the original position.
7-19
Air filter elements and check
hoses and V-belt case air filter
element
The air filter elements and the V-belt
case air filter element should be serviced at the intervals specified in the
periodic maintenance and lubrication
chart. Service all air filter elements
more frequently if you are riding in unusually wet or dusty areas.
Replacing the air filter elements
1. Place the scooter on the centerstand.
TIP
Continue as follows for each air filter element.
2. Remove the air filter case cover by
removing the rubber caps and
screws.
PERIODIC MAINTENANCE AND ADJUSTMENT
Left
3. Pull the air filter element out.
1
Left
2
1
1
3
1
3
1. Screw
2. Air filter case cover
3. Rubber cap
1. Air filter element
Right
Right
To clean the air filter check hoses
1. Check the hose at the bottom of
both air filter cases for accumulated dirt or water.
1
2
stalling the screws. NOTICE:
Make sure that each filter element is properly seated in its
case. Always replace both air filter elements at the same time,
otherwise poor engine performance or damage to the engine
may result. The engine should
never be operated without the
filter elements installed, otherwise the piston(s) and/or cylinder(s) may become excessively
worn.[ECA12923]
6. Install the rubber cap.
1
2
3
4
5
6
7
3
8
1
1. Screw
2. Air filter case cover
3. Rubber cap
9
1. Air filter element
4. Insert a new air filter element into
the air filter case.
5. Install the air filter case cover by in7-20
PERIODIC MAINTENANCE AND ADJUSTMENT
Left
1
2
1
3
Cleaning the V-belt case air filter element
1. Remove
cowling
E.
(See
page 7-8.)
2. Remove panel B. (See page 7-8.)
3. Remove the left air filter case cover.
4. Remove the V-belt air filter case
cover by removing the screws.
1
4
2
5
1
2
1. Screw
2. V-belt case air filter element
1. Air filter check hose
Right
1
6. Lightly tap the V-belt case air filter
element to remove most of the
dust and dirt, and then blow out the
dirt with compressed air as shown.
1
6
1
7
8
9
1. Screw
2. V-belt air filter case cover
1
1. Air filter check hose
5. Remove the V-belt case air filter
element by removing the screws.
2. If dirt or water is visible, remove
the hose, clean it, and then install
it.
7. Check the V-belt case air filter element for damage and replace it if
7-21
PERIODIC MAINTENANCE AND ADJUSTMENT
necessary.
8. Install the V-belt case air filter element by installing the screws.
NOTICE: Make sure that the
V-belt filter element is properly
seated in its case.[ECA12941]
9. Install the V-belt air filter case cover by installing the screws.
10. Install the left air filter case cover.
11. Install the panel.
12. Install the cowling.
EAU21382
Checking the throttle cable
free play
1
EAU21401
Valve clearance
The valve clearance changes with use,
resulting in improper air-fuel mixture
and/or engine noise. To prevent this
from occurring, the valve clearance
must be adjusted by a Yamaha dealer
at the intervals specified in the periodic
maintenance and lubrication chart.
2
3
4
1. Throttle cable free play
The throttle cable free play should measure 3.0–5.0 mm (0.12–0.20 in) at the
throttle grip. Periodically check the
throttle cable free play and, if necessary, have a Yamaha dealer adjust it.
5
6
7
8
9
7-22
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU21863
Tires
1
2
3
4
5
6
7
8
9
To maximize the performance, durability, and safe operation of your scooter,
note the following points regarding the
specified tires.
Tire air pressure
The tire air pressure should be checked
and, if necessary, adjusted before each
ride.
EWA10501
WARNING
Operation of this vehicle with improper tire pressure may cause severe injury or death from loss of
control.
● The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the temperature
of the tires equals the ambient
temperature).
● The tire air pressure must be adjusted in accordance with the
riding speed and with the total
weight of rider, passenger, cargo, and accessories approved
for this model.
Tire air pressure (measured on cold
tires):
0–90 kg (0–198 lb):
Front:
200 kPa (2.00 kgf/cm2, 29 psi)
Rear:
250 kPa (2.50 kgf/cm2, 36 psi)
90–196 kg (198–432 lb):
Front:
200 kPa (2.00 kgf/cm2, 29 psi)
Rear:
250 kPa (2.50 kgf/cm2, 36 psi)
Maximum load*:
196 kg (432 lb)
* Total weight of rider, passenger, cargo and accessories
EWA10511
WARNING
Never overload your vehicle. Operation of an overloaded vehicle could
cause an accident.
Tire inspection
2
1
3
1. Tire sidewall
2. Tire tread depth
3. Tire wear indicator
The tires must be checked before each
ride. If a tire tread shows crosswise
lines (minimum tread depth), if the tire
has a nail or glass fragments in it, or if
the sidewall is cracked, have a Yamaha
dealer replace the tire immediately.
Minimum tire tread depth (front and
rear):
1.0 mm (0.04 in)
TIP
The tire tread depth limits may differ
from country to country. Always comply
7-23
PERIODIC MAINTENANCE AND ADJUSTMENT
with the local regulations.
EAU21992
Tire information
This scooter is equipped with cast
wheels and tubeless tires with valves.
EWA10590
WARNING
Operating the scooter with excessively worn tires decrease riding
stability and can lead to loss of control. Have excessively worn tires replaced by a Yamaha dealer
immediately. Brakes, tires, and related wheel parts replacement should
be left to a Yamaha Service Technician.
After extensive tests, only the tires listed below have been approved for this
model by Yamaha Motor Co., Ltd.
Front tire:
Size:
120/80-14M/C 58S
Manufacturer/model:
IRC/MB67
DUNLOP/D305FL
Rear tire:
Size:
150/70-13M/C 64S
Manufacturer/model:
IRC/MB67
DUNLOP/D305L
Cast wheels
EWA10580
●
●
WARNING
It is dangerous to ride with a
worn-out tire. When a tire tread
begins to show crosswise lines,
have a Yamaha dealer replace
the tire immediately.
The replacement of all wheeland brake-related parts, including the tires, should be left to a
Yamaha dealer, who has the
necessary professional knowledge and experience.
7-24
To maximize the performance, durability, and safe operation of your vehicle,
note the following points regarding the
specified wheels.
● The wheel rims should be checked
for cracks, bends, warpage or
damage before each ride. If any
damage is found, have a Yamaha
dealer replace the wheel. Do not
attempt even the smallest repair to
the wheel. A deformed or cracked
wheel must be replaced.
● The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse handling characteristics, and a shortened tire life.
● Ride at moderate speeds after
changing a tire since the tire surface must first be “broken in” for it
to develop its optimal characteristics.
● After repairing or replacing the rear
tire, tighten the valve stem nut and
locknut to the specified torques.
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU33453
Front and rear brake lever free
play
brake lever ends. If there is free play,
have a Yamaha dealer inspect the
brake system.
EWA14211
Front
1
1
2
1
2
3
4
5
6
7
1. Valve stem nut
2. Valve stem locknut
Tightening torques:
Valve stem nut:
2.0 Nm (0.2 m·kgf, 1.1 ft·lbf)
Valve stem locknut:
3.0 Nm (0.3 m·kgf, 2.2 ft·lbf)
1. Brake lever free play
Rear
1
8
9
1. Brake lever free play
There should be no free play at the
7-25
WARNING
A soft or spongy feeling in the brake
lever can indicate the presence of air
in the hydraulic system. If there is air
in the hydraulic system, have a
Yamaha dealer bleed the system before operating the vehicle. Air in the
hydraulic system will diminish the
braking performance, which may result in loss of control and an accident.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU33473
Adjusting the rear brake lock
lever cable
To decrease the rear brake lock lever
cable length, turn the adjusting nut in
direction (b).
EWA10650
2
1
(a)
WARNING
If proper adjustment cannot be obtained as described, have a Yamaha
dealer make this adjustment.
EAU22390
Checking the front and rear
brake pads
The front and rear brake pads must be
checked for wear at the intervals specified in the periodic maintenance and
lubrication chart.
2
EAU22420
Front brake pads
(b)
3
4
1. Adjusting nut
2. Rear brake lock lever cable length
5
Rear brake lock lever cable adjustment
may be required if the rear brake lock
lever does not hold properly. When the
rear brake lock lever is not in use, the
rear brake lock lever cable length
should measure 45 mm to 47 mm (1.77
in to 1.85 in) at the rear brake caliper.
Periodically check the rear brake lock
lever cable length and, if necessary,
adjust it as follows.
To increase the rear brake lock lever
cable length, turn the adjusting nut at
the rear brake caliper in direction (a).
6
1
7
1. Wear indicator groove
Each front brake pad is provided with a
wear indicator groove, which allows
you to check the brake pad wear without having to disassemble the brake.
To check the brake pad wear, check
the wear indicator groove. If a brake
pad has worn to the point that the wear
7-26
8
9
PERIODIC MAINTENANCE AND ADJUSTMENT
indicator groove has almost disappeared, have a Yamaha dealer replace
the brake pads as a set.
1
2
3
EAU34210
Rear brake pads
Have a Yamaha dealer check each
rear brake pad for damage and measure the lining thickness and if necessary, replace them as a set.
EAU22580
Checking the brake fluid level
Front brake
1
4
5
1. Minimum level mark
Rear brake
6
1
7
ing it to become ineffective.
Before riding, check that the brake fluid
is above the minimum level mark and
replenish if necessary. A low brake fluid
level may indicate worn brake pads
and/or brake system leakage. If the
brake fluid level is low, be sure to check
the brake pads for wear and the brake
system for leakage.
Observe these precautions:
● When checking the fluid level,
make sure that the top of the brake
fluid reservoir is level.
● Use only the recommended quality
brake fluid, otherwise the rubber
seals may deteriorate, causing
leakage and poor braking performance.
Recommended brake fluid:
DOT 4
8
●
9
1. Minimum level mark
Insufficient brake fluid may allow air to
enter the brake system, possibly caus7-27
●
Refill with the same type of brake
fluid. Mixing fluids may result in a
harmful chemical reaction and
lead to poor braking performance.
Be careful that water does not enter the brake fluid reservoir when
refilling. Water will significantly
PERIODIC MAINTENANCE AND ADJUSTMENT
●
●
lower the boiling point of the fluid
and may result in vapor lock.
Brake fluid may deteriorate painted surfaces or plastic parts. Always clean up spilled fluid
immediately.
As the brake pads wear, it is normal for the brake fluid level to gradually go down. However, if the
brake fluid level goes down suddenly, have a Yamaha dealer
check the cause.
EAU22731
Changing the brake fluid
Have a Yamaha dealer change the
brake fluid at the intervals specified in
the TIP after the periodic maintenance
and lubrication chart. In addition, have
the oil seals of the master cylinders and
calipers as well as the brake hoses replaced at the intervals listed below or
whenever they are damaged or leaking.
● Oil seals: Replace every two
years.
● Brake hoses: Replace every four
years.
EAU23093
Checking and lubricating the
cables
The operation of all control cables and
the condition of the cables should be
checked before each ride, and the cables and cable ends should be lubricated if necessary. If a cable is damaged
or does not move smoothly, have a
Yamaha dealer check or replace it.
WARNING! Damage to the outer
housing of cables may result in internal rusting and cause interference with cable movement. Replace
damaged cables as soon as possible to prevent unsafe conditions.[EWA10711]
Recommended lubricant:
Yamaha Chain and Cable Lube or
engine oil
2
3
4
5
6
7
8
9
7-28
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU23111
Checking and lubricating the
throttle grip and cable
1
2
EAU23172
Lubricating the front and rear
brake levers
EAU23213
Checking and lubricating the
centerstand and sidestand
The operation of the throttle grip should
be checked before each ride. In addition, the cable should be lubricated at
the intervals specified in the periodic
maintenance chart.
3
4
5
6
7
The pivoting points of the front and rear
brake levers must be lubricated at the
intervals specified in the periodic maintenance and lubrication chart.
Recommended lubricant:
Silicone grease
8
The operation of the centerstand and
sidestand should be checked before
each ride, and the pivots and metal-to-metal contact surfaces should be
lubricated if necessary.
9
7-29
PERIODIC MAINTENANCE AND ADJUSTMENT
EWA10741
WARNING
If the centerstand or sidestand does
not move up and down smoothly,
have a Yamaha dealer check or repair it. Otherwise, the centerstand or
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
EAU23272
Checking the front fork
The condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic maintenance and lubrication chart.
2
To check the condition
Check the inner tubes for scratches,
damage and excessive oil leakage.
3
ECA10590
Recommended lubricant:
Lithium-soap-based grease
To check the operation
1. Place the vehicle on a level surface and hold it in an upright position. WARNING! To avoid injury,
securely support the vehicle so
there is no danger of it falling
over.[EWA10751]
2. While applying the front brake,
push down hard on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.
NOTICE
If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or repair it.
4
5
6
7
8
9
7-30
PERIODIC MAINTENANCE AND ADJUSTMENT
1
2
3
4
5
6
EAU45511
EAU23290
Checking the steering
Checking the wheel bearings
Worn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as follows at the intervals specified in the periodic maintenance and lubrication
chart.
1. Place the vehicle on the centerstand. WARNING! To avoid injury, securely support the vehicle
so there is no danger of it falling
over.[EWA10751]
2. Hold the lower ends of the front
fork legs and try to move them forward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steering.
The front and rear wheel bearings must
be checked at the intervals specified in
the periodic maintenance and lubrication chart. If there is play in the wheel
hub or if the wheel does not turn
smoothly, have a Yamaha dealer check
the wheel bearings.
EAU34224
Battery
1
1. Battery
The battery is located behind cowling
A. (See page 7-8.)
This model is equipped with a VRLA
(Valve Regulated Lead Acid) battery.
There is no need to check the electrolyte or to add distilled water. However,
the battery lead connections need to be
checked and, if necessary, tightened.
7
8
EWA10760
9
●
7-31
WARNING
Electrolyte is poisonous and
dangerous since it contains sulfuric acid, which causes severe
burns. Avoid any contact with
skin, eyes or clothing and al-
PERIODIC MAINTENANCE AND ADJUSTMENT
ways shield your eyes when
working near batteries. In case
of contact, administer the following FIRST AID.
EXTERNAL: Flush with plenty
of water.
INTERNAL: Drink large quantities of water or milk and immediately call a physician.
EYES: Flush with water for 15
minutes and seek prompt
medical attention.
Batteries produce explosive hydrogen gas. Therefore, keep
sparks, flames, cigarettes, etc.,
away from the battery and provide sufficient ventilation when
charging it in an enclosed
space.
KEEP THIS AND ALL BATTERIES OUT OF THE REACH OF
CHILDREN.
●
●
●
●
●
To charge the battery
Have a Yamaha dealer charge the battery as soon as possible if it seems to
have discharged. Keep in mind that the
battery tends to discharge more quickly
if the vehicle is equipped with optional
electrical accessories.
ECA16520
NOTICE
To charge a VRLA (Valve Regulated
Lead Acid) battery, a special (constant-voltage) battery charger is required. Using a conventional battery
charger will damage the battery. If
you do not have access to a constant-voltage battery charger, have a
Yamaha dealer charge your battery.
To store the battery
1. If the vehicle will not be used for
more than one month, remove the
battery, fully charge it, and then
place it in a cool, dry place.
NOTICE: When removing the
battery, be sure the key is
turned to “OFF”, then disconnect the negative lead before
disconnecting
the
positive
lead.[ECA16302]
2. If the battery will be stored for more
than two months, check it at least
once a month and fully charge it if
necessary.
7-32
3. Fully charge the battery before installation.
4. After installation, make sure that
the battery leads are properly connected to the battery terminals.
ECA16530
NOTICE
Always keep the battery charged.
Storing a discharged battery can
cause permanent battery damage.
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU34233
Replacing the fuses
1
2
3
4
5
6
7
8
9
The main fuse and the fuse box, which
contains the fuses for the individual circuits, are located behind cowling A.
(See page 7-8.)
If a fuse is blown, replace it as follows.
1. Turn the key to “OFF” and turn off
the electrical circuit in question.
2. Remove the blown fuse, and then
install a new fuse of the specified
amperage. WARNING! Do not
use a fuse of a higher amperage
rating than recommended to
avoid causing extensive damage to the electrical system and
possibly a fire.[EWA15131]
7
2
1
1. Spare main fuse
2. Main fuse
1.
2.
3.
4.
5.
6.
7.
TIP
If the main fuse is blown, remove the
grab bar to access the main fuse. After
replacing the main fuse, install the grab
bar. (See page 7-8.)
1
2
1. Fuse box
2. Taillight fuse
7-33
1
2
3
4
5
6
Ignition fuse
Signaling system fuse
Headlight fuse
Radiator fan fuse
Backup fuse (for odometer and clock)
Fuel injection system fuse
Spare fuse
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU34240
Specified fuses:
Main fuse:
40.0 A
Ignition fuse:
10.0 A
Signaling system fuse:
10.0 A
Headlight fuse:
20.0 A
Taillight fuse:
10.0 A
Radiator fan fuse:
10.0 A
Fuel injection system fuse:
10.0 A
Backup fuse:
10.0 A
EAU24181
Replacing a headlight bulb
Tail/brake light
This model is equipped with quartz bulb
headlights. If a headlight bulb burns
out, have a Yamaha dealer replace it
and, if necessary, adjust the headlight
beam.
This model is equipped with an
LED-type tail/brake light.
If the tail/brake light does not come on,
have a Yamaha dealer check it.
2
3
4
5
3. Turn the key to “ON” and turn on
the electrical circuit in question to
check if the device operates.
4. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
6
7
8
9
7-34
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU36124
Replacing a front turn signal
light bulb
1
2
1
1. Place the scooter on the centerstand.
2. Remove panel A. (See page 7-8.)
3. Remove the windshield by removing the screws.
3
2
2
1
4
clockwise.
7. Insert a new bulb into the socket,
push it in, and then turn it clockwise until it stops.
8. Install the socket (together with the
bulb) by turning it clockwise.
9. Place the turn signal light unit in
the original position, and then install the screws.
1. Screw
2. Front turn signal light unit
5. Remove the socket (together with
the bulb) by turning it counterclockwise.
5
6
1
7
8
1. Screw
2. Windshield
10. Install the windshield by installing
the screws.
11. Install panel A.
4. Remove the front turn signal light
unit by removing the screws.
9
1. Turn signal light bulb socket
6. Remove the burnt-out bulb by
pushing it in and turning it counter7-35
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU34263
Replacing a rear turn signal
light bulb
1. Place the scooter on the centerstand.
2. Remove cowling C for replacing
the left turn signal light bulb or
cowling D for replacing the right
turn signal light bulb. (See
page 7-8.)
3. Remove the socket (together with
the turn signal light bulb) by turning
it counterclockwise.
push it in, and then turn it clockwise until it stops.
6. Install the socket (together with the
bulb) by turning it clockwise.
7. Install the cowling removed.
EAU34273
Replacing the license plate
light bulb
1. Place the scooter on the centerstand.
2. Remove
cowling
B.
(See
page 7-8.)
3. Remove the license plate light cover and license plate light lens by
removing the screws.
2
3
4
1
2
5
6
1
3
1. License plate light lens
2. License plate light cover
3. Screw
1. Turn signal light bulb socket
4. Remove the burnt-out bulb by
pushing it in and turning it counterclockwise.
4. Remove the burnt-out bulb by
pushing it in and turning it counterclockwise.
5. Insert a new bulb into the socket,
7-36
7
8
9
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU25881
1
1
2
3
1. Bulb
4
5
6
7
8
9
5. Insert a new bulb into the socket,
push it in, and then turn it clockwise until it stops.
6. Install the license plate light lens
and license plate light cover by installing the screws.
7. Install the cowling.
Troubleshooting
Although Yamaha scooters receive a
thorough inspection before shipment
from the factory, trouble may occur during operation. Any problem in the fuel,
compression, or ignition systems, for
example, can cause poor starting and
loss of power.
The following troubleshooting charts
represent quick and easy procedures
for checking these vital systems yourself. However, should your scooter require any repair, take it to a Yamaha
dealer, whose skilled technicians have
the necessary tools, experience, and
know-how to service the scooter properly.
Use only genuine Yamaha replacement parts. Imitation parts may look like
Yamaha parts, but they are often inferior, have a shorter service life and can
lead to expensive repair bills.
EWA15141
WARNING
When checking the fuel system, do
not smoke, and make sure there are
no open flames or sparks in the area, including pilot lights from water
7-37
heaters or furnaces. Gasoline or
gasoline vapors can ignite or explode, causing severe injury or
property damage.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU42701
Troubleshooting charts
Starting problems or poor engine performance
1. Fuel
There is enough fuel.
Check the compression.
There is no fuel.
Supply fuel.
Check the fuel level in
the fuel tank.
The engine does not start.
Check the compression.
2
3
2. Compression
There is compression.
Check the ignition.
4
Operate the electric starter.
There is no compression.
3. Ignition
Have a Yamaha dealer
check the vehicle.
5
Wet
Wipe off with a dry cloth and correct the
spark plug gap, or replace the spark plug.
Operate the electric starter.
6
Dry
Have a Yamaha dealer check the vehicle.
The engine does not start.
Check the battery.
7
Remove the spark plug
and check the electrodes.
4. Battery
8
The engine turns over
quickly.
The battery is good.
The engine turns over
slowly.
Check the battery lead connections,
and charge the battery if necessary.
Operate the electric starter.
7-38
The engine does not start.
Have a Yamaha dealer
check the vehicle.
9
PERIODIC MAINTENANCE AND ADJUSTMENT
Engine overheating
EWAT1040
●
1
●
2
WARNING
Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.
Place a thick rag, like a towel, over the radiator cap, and then slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape. When the hissing sound has stopped, press down on the cap
while turning it counterclockwise, and then remove the cap.
3
The coolant level is low.
Check the cooling system
for leakage.
4
5
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.
There is
leakage.
There is
no leakage.
Have a Yamaha dealer check
and repair the cooling system.
Add coolant. (See TIP.)
Start the engine. If the engine overheats again, have a
Yamaha dealer check and repair the cooling system.
6
7
TIP
If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolant
as soon as possible.
8
9
7-39
SCOOTER CARE AND STORAGE
EAU37833
Matte color caution
EAU26093
Care
ECA15192
NOTICE
Some models are equipped with
matte colored finished parts. Be
sure to consult a Yamaha dealer for
advice on what products to use before cleaning the vehicle. Using a
brush, harsh chemical products or
cleaning compounds when cleaning
these parts will scratch or damage
their surface. Wax also should not
be applied to any matte colored finished parts.
While the open design of a scooter reveals the attractiveness of the technology, it also makes it more vulnerable.
Rust and corrosion can develop even if
high-quality components are used. A
rusty exhaust pipe may go unnoticed
on a car, however, it detracts from the
overall appearance of a scooter. Frequent and proper care does not only
comply with the terms of the warranty,
but it will also keep your scooter looking
good, extend its life and optimize its
performance.
Before cleaning
1. Cover the muffler outlet with a
plastic bag after the engine has
cooled down.
2. Make sure that all caps and covers
as well as all electrical couplers
and connectors, including the
spark plug cap, are tightly installed.
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such prod8-1
ucts onto seals, gaskets and wheel
axles. Always rinse the dirt and degreaser off with water.
Cleaning
ECA10782
NOTICE
● Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the affected area any longer than instructed. Also, thoroughly rinse
the area off with water, immediately dry it, and then apply a corrosion protection spray.
● Improper cleaning can damage
plastic parts (such as cowlings,
panels, windshields, headlight
lenses, meter lenses, etc.) and
the mufflers. Use only a soft,
clean cloth or sponge with water to clean plastic. However, if
the plastic parts cannot be thoroughly cleaned with water, diluted mild detergent with water
may be used. Be sure to rinse
off any detergent residue using
2
3
4
5
6
7
8
9
SCOOTER CARE AND STORAGE
●
1
2
3
4
●
5
6
7
8
9
●
plenty of water, as it is harmful
to plastic parts.
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust removers or inhibitors, brake fluid, antifreeze or electrolyte.
Do not use high-pressure washers or steam-jet cleaners since
they cause water seepage and
deterioration in the following areas: seals (of wheel and swingarm bearings, fork and brakes),
electric components (couplers,
connectors,
instruments,
switches and lights), breather
hoses and vents.
For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning compounds for plastic may leave
scratches on the windshield.
Test the product on a small hidden part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing
compound
after
washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea or
on salt-sprayed roads
Since sea salt or salt sprayed on the
roads during winter are extremely corrosive in combination with water, carry
out the following steps after each ride in
the rain, near the sea or on
salt-sprayed roads.
TIP
Salt sprayed on roads in the winter may
8-2
remain well into spring.
1. Clean the scooter with cold water
and a mild detergent after the engine has cooled down. NOTICE:
Do not use warm water since it
increases the corrosive action
of the salt.[ECA10791]
2. Apply a corrosion protection spray
on all metal, including chrome- and
nickel-plated, surfaces to prevent
corrosion.
After cleaning
1. Dry the scooter with a chamois or
an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stainless-steel parts, including the exhaust system. (Even the thermally
induced discoloring of stainless-steel exhaust systems can be
removed through polishing.)
3. To prevent corrosion, it is recommended to apply a corrosion protection spray on all metal,
including chrome- and nickel-plated, surfaces.
4. Use spray oil as a universal clean-
SCOOTER CARE AND STORAGE
er to remove any remaining dirt.
5. Touch up minor paint damage
caused by stones, etc.
6. Wax all painted surfaces.
7. Let the scooter dry completely before storing or covering it.
EWA10941
WARNING
Contaminants on the brakes or tires
can cause loss of control.
● Make sure that there is no oil or
wax on the brakes or tires. If
necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or acetone, and wash the tires with
warm water and a mild detergent.
● Before operating the scooter
test its braking performance
and cornering behavior.
●
treat them with a suitable care
product.
Avoid using abrasive polishing
compounds as they will wear
away the paint.
TIP
●
●
Consult a Yamaha dealer for advice on what products to use.
Washing, rainy weather or humid
climates can cause the headlight
lens to fog. Turning the headlight
on for a short period of time will
help remove the moisture from the
lens.
EAU36561
Storage
Short-term
Always store your scooter in a cool, dry
place and, if necessary, protect it
against dust with a porous cover.
ECA10820
NOTICE
● Storing the scooter in a poorly
ventilated room or covering it
with a tarp, while it is still wet,
will allow water and humidity to
seep in and cause rust.
● To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemicals are stored.
Long-term
Before storing your scooter for several
months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
ECA10800
NOTICE
● Apply spray oil and wax sparingly and make sure to wipe off
any excess.
● Never apply oil or wax to any
rubber and plastic parts, but
8-3
2
3
4
5
6
7
8
9
SCOOTER CARE AND STORAGE
1
2
3
4
5
6
7
8
9
fuel from deteriorating.
3. Perform the following steps to protect the cylinder, piston rings, etc.
from corrosion.
a. Remove the spark plug cap
and spark plug.
b. Pour a teaspoonful of engine oil
into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit sparking during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap
from the spark plug, and then
install the spark plug and the
spark plug cap. WARNING! To
prevent damage or injury
from sparking, make sure to
ground the spark plug electrodes while turning the engine over.[EWA10951]
4. Lubricate all control cables and the
pivoting points of all levers and
pedals as well as of the sidestand/
centerstand.
5. Check and, if necessary, correct
the tire air pressure, and then lift
the scooter so that both of its
wheels are off the ground. Alternatively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
6. Cover the muffler outlet with a
plastic bag to prevent moisture
from entering it.
7. Remove the battery and fully
charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an excessively cold or warm place [less
than 0 °C (30 °F) or more than 30
°C (90 °F)]. For more information
on storing the battery, see page
7-31.
TIP
Make any necessary repairs before
storing the scooter.
8-4
SPECIFICATIONS
Dimensions:
Overall length:
2230 mm (87.8 in)
Overall width:
780 mm (30.7 in)
Overall height:
1380 mm (54.3 in)
Seat height:
760 mm (29.9 in)
Wheelbase:
1565 mm (61.6 in)
Ground clearance:
120 mm (4.72 in)
Minimum turning radius:
2600 mm (102.4 in)
Weight:
With oil and fuel:
212.0 kg (467 lb)
Engine:
Engine type:
Liquid cooled 4-stroke, DOHC
Cylinder arrangement:
Forward-inclined single cylinder
Displacement:
395 cm3
Bore × stroke:
83.0 × 73.0 mm (3.27 × 2.87 in)
Compression ratio:
10.60 :1
Starting system:
Electric starter
Lubrication system:
Wet sump
EAU2633X
Engine oil:
Air filter:
Recommended brand:
YAMALUBE
Type:
SAE 10W-40 or SAE 20W-50
0
10
30
50
70
90 110 130 ˚F
YAMALUBE 10W-40
or SAE 10W-40
0
10
20
30
Fuel:
Recommended fuel:
Unleaded gasoline only
Fuel tank capacity:
14.0 L (3.70 US gal, 3.08 Imp.gal)
Fuel injection:
Throttle body:
ID mark:
5RUT 30
YAMALUBE 20W-50
or SAE 20W-50
–20 –10
Air filter element:
Oil-coated paper element
40
50 ˚C
Recommended engine oil grade:
API service SG type or higher, JASO standard MA
Engine oil quantity:
Without oil filter element replacement:
1.50 L (1.59 US qt, 1.32 Imp.qt)
With oil filter element replacement:
1.70 L (1.80 US qt, 1.50 Imp.qt)
Final transmission oil:
Type:
YAMALUBE 10W-40 or SAE 10W-30 type
SE motor oil
Quantity:
0.25 L (0.26 US qt, 0.22 Imp.qt)
Cooling system:
Coolant reservoir capacity (up to the maximum level mark):
0.32 L (0.34 US qt, 0.28 Imp.qt)
Radiator capacity (including all routes):
1.57 L (1.66 US qt, 1.38 Imp.qt)
9-1
2
3
Spark plug (s):
Manufacturer/model:
NGK/CR7E
Spark plug gap:
0.7–0.8 mm (0.028–0.031 in)
4
5
Clutch:
Clutch type:
Dry, centrifugal automatic
6
Transmission:
Primary reduction system:
Helical gear
Primary reduction ratio:
31/14 (2.214)
Secondary reduction system:
Helical gear
Secondary reduction ratio:
42/16 (2.625)
Transmission type:
V-belt automatic
Operation:
Centrifugal automatic type
7
8
9
SPECIFICATIONS
Chassis:
1
2
3
4
5
Frame type:
Aluminum die-cast and steel tube backbone
Caster angle:
27.00 °
Trail:
100.0 mm (3.94 in)
Front tire:
Type:
Tubeless
Size:
120/80-14M/C 58S
Manufacturer/model:
IRC/MB67
Manufacturer/model:
DUNLOP/D305FL
Rear tire:
6
7
8
Type:
Tubeless
Size:
150/70-13M/C 64S
Manufacturer/model:
IRC/MB67
Manufacturer/model:
DUNLOP/D305L
Loading:
9
Maximum load:
196 kg (432 lb)
* (Total weight of rider, passenger, cargo
and accessories)
Tire air pressure (measured on cold
tires):
Loading condition:
0–90 kg (0–198 lb)
Front:
200 kPa (2.00 kgf/cm2, 29 psi)
Rear:
250 kPa (2.50 kgf/cm2, 36 psi)
Loading condition:
90–196 kg (198–432 lb)
Front:
200 kPa (2.00 kgf/cm2, 29 psi)
Rear:
250 kPa (2.50 kgf/cm2, 36 psi)
Front wheel:
Wheel type:
Cast wheel
Rim size:
14 x MT3.00
Operation:
Left hand operation
Recommended fluid:
DOT 4
Front suspension:
Type:
Telescopic fork
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
120.0 mm (4.72 in)
Rear suspension:
Type:
Unit swing
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
104.0 mm (4.09 in)
Electrical system:
Rear wheel:
Ignition system:
TCI (digital)
Charging system:
AC magneto
Wheel type:
Cast wheel
Rim size:
13 x MT4.00
Battery:
Front brake:
Type:
Single disc brake
Operation:
Right hand operation
Recommended fluid:
DOT 4
Model:
GT9B-4
Voltage, capacity:
12 V, 8.0 Ah
Headlight:
Bulb type:
Halogen bulb
Bulb voltage, wattage × quantity:
Rear brake:
Type:
Single disc brake
9-2
Headlight:
12 V, 60 W/55 W × 2
SPECIFICATIONS
Tail/brake light:
LED
Front turn signal/position light:
12 V, 21 W/5.0 W × 2
Rear turn signal light:
12 V, 21.0 W × 2
License plate light:
12 V, 5.0 W × 1
Meter lighting:
12 V, 2.0 W × 3
High beam indicator light:
12 V, 1.4 W × 1
Turn signal indicator light:
12 V, 1.4 W × 2
Engine trouble warning light:
12 V, 1.4 W × 1
2
3
4
Fuses:
5
Main fuse:
40.0 A
Headlight fuse:
20.0 A
Taillight fuse:
10.0 A
Signaling system fuse:
10.0 A
Ignition fuse:
10.0 A
Radiator fan fuse:
10.0 A
Fuel injection system fuse:
10.0 A
Backup fuse:
10.0 A
6
7
8
9
9-3
CONSUMER INFORMATION
EAU26352
Identification numbers
1
2
3
Record the key identification number,
vehicle identification number and model label information in the spaces provided below for assistance when
ordering spare parts from a Yamaha
dealer or for reference in case the vehicle is stolen.
KEY IDENTIFICATION NUMBER:
4
1
VEHICLE IDENTIFICATION
NUMBER:
The key identification number is
stamped into the key tag. Record this
number in the space provided and use
it for reference when ordering a new
key.
7
8
EAU26410
Vehicle identification number
1
1. Key identification number
5
6
EAU26381
Key identification number
MODEL LABEL INFORMATION:
9
10
10-1
1. Vehicle identification number
The vehicle identification number is
stamped into the frame.
TIP
The vehicle identification number is
used to identify your vehicle and may
be used to register it with the licensing
authority in your area.
CONSUMER INFORMATION
EAU26500
Model label
EAU48060
Vehicle Emission Control
Information label
1
1
2
3
4
1. Model label
The model label is affixed to the inside
of the rear storage compartment. (See
page 4-14.) Record the information on
this label in the space provided. This information will be needed when ordering
spare parts from a Yamaha dealer.
1. Vehicle Emission Control Information
label
The Vehicle Emission Control Information label is affixed at the location in the
illustration. This label shows specifications related to exhaust emissions as
required by federal law, state law and
Environment Canada.
5
6
7
8
9
10
10-2
CONSUMER INFORMATION
EAU26551
Reporting safety defects
1
2
3
If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately
inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation,
U.S.A. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group
of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems
between you, your dealer, or Yamaha Motor Corporation, U.S.A.
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://
www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, DC 20590. You can also obtain
other information about motor vehicle safety from http://www.safercar.gov.
4
5
6
7
8
9
10
10-3
CONSUMER INFORMATION
EAU26580
Scooter noise regulation
TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED:
Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any person other
than for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the use of
the vehicle after such device or element of design has been removed or rendered inoperative by any person.
“AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED BELOW.”
These acts include tampering with the following systems; i.e., modification, removal, etc.
Exhaust system
● Muffler
● Exhaust pipe
● Silencer
Intake system
● Air cleaner case
● Air cleaner element
● Intake duct
2
3
4
5
6
7
8
9
10
10-4
CONSUMER INFORMATION
EAU26632
Maintenance record
1
2
3
4
5
6
7
8
9
10
Copies of work orders and/or receipts for parts purchased and installed on your vehicle will be required to document that
maintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a reminder
that maintenance work is required. It is not acceptable proof of maintenance work.
Maintenance
interval
Date of
service
Servicing dealer
name and address
Mileage
600 mi
(1000 km) or
1 month
4000 mi
(7000 km) or
6 months
8000 mi
(13000 km) or
12 months
12000 mi
(19000 km) or
18 months
16000 mi
(25000 km) or
24 months
20000 mi
(31000 km) or
30 months
24000 mi
(37000 km) or
36 months
28000 mi
(43000 km) or
42 months
32000 mi
(49000 km) or
48 months
10-5
Remarks
CONSUMER INFORMATION
Maintenance
interval
Date of
service
Servicing dealer
name and address
Mileage
36000 mi
(55000 km) or
54 months
40000 mi
(61000 km) or
60 months
Remarks
2
3
4
5
6
7
8
9
10
10-6
CONSUMER INFORMATION
EAU26663
YAMAHA MOTOR CORPORATION, U.S.A. STREET AND ENDURO MOTORCYCLE LIMITED
WARRANTY
1
2
3
4
5
6
7
8
9
Yamaha Motor Corporation, U.S.A. hereby warrants that
new Yamaha motorcycles will be free from defects in
material and workmanship for the period of time stated
herein, subject to certain stated limitations.
THE PERIOD OF WARRANTY for Yamaha motorcycles
originally equipped with headlight, stoplight, and turn
signals shall be one (1) year from the date of purchase,
with no mileage limitation.
MODELS EXCLUDED FROM WARRANTY include
those used for non-Yamaha-authorized renting, leasing
or other commercial purposes, and TZ models.
DURING THE PERIOD OF WARRANTY, any authorized
Yamaha motorcycle dealer will, free of charge, repair or
replace any part adjudged defective by Yamaha due to
faulty workmanship or material from the factory. Parts used
in warranty repairs will be warranted for the balance of the
product’s warranty period. All parts replaced under
warranty become property of Yamaha Motor Corporation,
U.S.A.
GENERAL EXCLUSIONS from this warranty shall
include any failures caused by:
a) Competition or racing use.
b) Installation of parts or accessories that are not
qualitatively equivalent to genuine Yamaha parts.
c) Abnormal strain, neglect, or abuse.
d) Lack of proper maintenance.
e) Accident or collision damage.
f) Modification to original parts.
THE CUSTOMER’S RESPONSIBILITY under this
warranty shall be to:
1. Operate and maintain the motorcycle as specified in
the appropriate Owner’s Manual, and
2. Give notice to an authorized Yamaha motorcycle
dealer of any and all apparent defects within ten (10)
days after discovery, and make the machine available
at that time for inspection and repairs at such dealer’s
place of business.
WARRANTY TRANSFER: To transfer the warranty from
the original purchaser to any subsequent purchaser, it is
imperative that the machine be inspected and registered
for warranty by an authorized Yamaha motorcycle dealer.
In order for this warranty to remain in effect, this
inspection and registration must take place within ten
(10) days after transfer. An inspection and registration fee
will be charged for this service.
EMISSION CONTROL SYSTEM WARRANTY:
Yamaha Motor Corporation, U.S.A. also warrants to the
ultimate purchaser and each subsequent purchaser of
each Yamaha motorcycle covered by this warranty with a
displacement of 50cc or greater, that the vehicle is
designed, built, and equipped so as to conform at the
time of sale with all U.S. emissions standards applicable
at the time of manufacture and that it is free from defects
in materials and workmanship which would cause it not
to meet these standards within the period listed
immediately below. Failures other than those resulting
from defects in material or workmanship, which arise
solely as a result of owner abuse and/or lack of proper
maintenance, are not covered by this warranty.
SPECIFIC EXCLUSIONS from this warranty shall
include parts replaced due to normal wear or routine
maintenance.
Engine
Displacement
Under 50cc
Period
6,000 km (3,750 miles)
or five years, whichever occurs first
50cc to 169cc
12,000 km (7,465 miles)
or five years whichever occurs first
170cc to 279cc
18,000 km (11,185 miles)
or five years, whichever occurs first
280cc and over
30,000 km (18,641 miles)
or five years, whichever occurs first
YAMAHA MOTOR CORPORATION, U.S.A. MAKES NO
OTHER WARRANTY OF ANY KIND, EXPRESSED OR
IMPLIED.
ALL
IMPLIED
WARRANTIES
OF
MERCHANTABILITY
AND
FITNESS
FOR
A
PARTICULAR PURPOSE WHICH EXCEED THE
OBLIGATIONS AND TIME LIMITS STATED IN THIS
WARRANTY ARE HEREBY DISCLAIMED BY YAMAHA
MOTOR CORPORATION, U.S.A. AND EXCLUDED
FROM THIS WARRANTY.
SOME STATES DO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY LASTS, SO THE
ABOVE LIMITATION MAY NOT APPLY TO YOU. ALSO
EXCLUDED FROM THIS WARRANTY ARE ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES
INCLUDING LOSS OF USE. SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.
10
YAMAHA MOTOR CORPORATION, U.S.A.
P.O. Box 6555
Cypress, California 90630
10-7
CONSUMER INFORMATION
WARRANTY QUESTIONS AND ANSWERS
CUSTOMER SERVICE
Q. What costs are my responsibility during the warranty period?
A. The customer’s responsibility includes all costs of normal maintenance services,
non-warranty repairs, accident and collision damages, and oil, oil filters, air filters,
spark plugs, and brake shoes.
If your machine requires warranty service, you must take it to any authorized Yamaha
motorcycle dealer within the continental United States. Be sure to bring your warranty
registration card or other valid proof of the original date of purchase. If a question or
problem arises regarding the warranty, first contact the owner of the dealership. Since
all warranty matters are handled at the dealer level, this person is in the best position to
help you. IF you are still not satisfied and require additional assistance, please write to:
Q. What are some examples of “abnormal” strain, neglect, or abuse?
A. These terms are general and overlap each other in areas. Specific examples
include: Running the machine out of oil, sustained high rpm, full-throttle, operating
the machine with a broken or damaged part which causes another part to fail,
damage or failure due to improper or careless transportation and/or tie-down. If
you have any specific questions on operation or maintenance, please contact your
dealer for advice.
YAMAHA MOTOR CORPORATION, U.S.A.
CUSTOMER RELATIONS DEPARTMENT
P.O. Box 6555
Cypress, California 90630
Q. Does the warranty cover incidental costs such as towing or transportation due to
a failure?
A. No. The warranty is limited to repair of the machine itself.
Q. May I perform any or all of the recommended maintenance shown in the Owner’s
Manual instead of having the dealer do them?
A. Yes, if you are a qualified mechanic and follow the procedures specified in the
Owner’s and Service Manual. We do recommend, however, that items requiring
special tools or equipment be done by a Yamaha motorcycle dealer.
When contacting Yamaha Motor Corporation, U.S.A., don’t forget to include any
important information such as names, addresses, model, V.I.N. (frame number),
dates, and receipts.
3
CHANGE OF ADDRESS
4
The federal government requires each manufacturer of a motor vehicle to maintain a
complete, up-to-date list of all first purchasers against the possibility of a safetyrelated defect and recall. This list is compiled from the purchase registrations sent to
Yamaha Motor Corporation, U.S.A. by the selling dealer at the time of your purchase.
Q. Will the warranty be void or cancelled if I do not operate or maintain my new
motorcycle exactly as specified in the Owner’s Manual?
A. No. The warranty on a new motorcycle cannot be “voided” or “cancelled.” However,
if a particular failure is caused by operation or maintenance other than as
described in the Owner’s Manual, that failure may not be covered under
warranty.
If you should move after you have purchased your new motorcycle, please advise us
of your new address by sending a postcard listing your motorcycle model name, V.I.N.
(frame number), dealer number (or dealer’s name) as it is shown on your warranty
card, your name and new mailing address. Mail to:
YAMAHA MOTOR CORPORATION, U.S.A.
P.O. Box 6555
Cypress, California 90630
Attention: Warranty Department
Q. What responsibility does my dealer have under this warranty?
A. Each Yamaha motorcycle dealer is expected to:
1. Completely set up every new machine before sale.
2. Explain the operation, maintenance, and warranty requirements to your
satisfaction at the time of sale, and upon your request at any later date.
3. Each Yamaha motorcycle dealer is held responsible for his setup, service and
warranty repair work.
2
This will ensure that Yamaha Motor Corporation, U.S.A. has an up-to-date registration
record in accordance with federal law.
5
6
7
8
9
Q. Is the warranty transferable to second owners?
A. Yes. The remainder of the existing warranty can be transferred upon request. The
unit has to be inspected and re-registered by an authorized Yamaha motorcycle
dealer for the policy to remain effective.
10
10-8
CONSUMER INFORMATION
EAU26750
YAMAHA EXTENDED SERVICE (Y.E.S.)
Keep your Yamaha protected even after your warranty
expires with genuine Yamaha Extended Service (Y.E.S.).
1
2
3
4
5
6
7
8
In addition, Travel and Recreation Interruption Protection
(TRIP) is included at no extra cost. TRIP gives you up to
$150 reimbursement per occurrence for any reasonable
expenses you incur because your Yamaha needs
covered service: replacement vehicle rental, emergency
towing, phone calls, even food and lodging when you are
away from home. This superb coverage goes into effect
when you purchase Y.E.S., so it applies to any warranty
repairs as well as covered repairs during your entire
Y.E.S. plan period.
Y.E.S. is designed and administered by Yamaha Motor
Corporation to provide maximum owner satisfaction. You
get uninterrupted factory-backed coverage for extra
peace of mind.
Y.E.S. is flexible. You choose the plan that’s right for
you: 12 months, 24 months, 36 months or, on certain
models, even 48 months beyond your warranty period.
Y.E.S. coverage is honored at any authorized Yamaha
dealer nationwide.
Y.E.S. is designed and administered by the same
Yamaha people who handle your warranty – and it
shows in the comprehensive coverage benefits. There
are no mileage limitations. Coverage isn’t limited to
“moving parts” or the “drive train” like many other plans.
And Y.E.S. covers manufacturing defects just like the
warranty. See the sample contract at your Yamaha
dealer to see how comforting uninterrupted factorybacked protection can be.
Y.E.S. coverage is transferable to a new owner if you
sell or trade-in. That can make your Yamaha much more
valuable!
This excellent Y.E.S. plan coverage is only available to
Yamaha owners like you, and only while your Yamaha is still
within the Yamaha Limited Warranty period. So visit your
authorized Yamaha dealer to get all the facts. He can show
you how easy it is to protect your investment with Yamaha
Extended Service.
You don’t have to pay anything for covered repairs.
There’s no deductible to pay, and repairs aren’t
“pro-rated.” You don’t have any “out-of-pocket” expenses
for covered repairs.
9
10
10-9
CONSUMER INFORMATION
We urge you to act now. You’ll get the excellent benefits of
TRIP coverage right away, and you’ll rest easy knowing
you’ll have strong factory-backed protection even after your
Yamaha Limited Warranty expires.
A special note:
If visiting your dealer isn’t convenient, contact Yamaha with
your Primary ID number (your frame number). We’ll be
happy to help you get the Y.E.S. coverage you need.
2
Yamaha Service Marketing
P.O. Box 6555
Cypress, CA 90630
1-(866)-YES-EXTD (1-866-937-3983)
3
4
5
6
7
8
9
10
10-10
INDEX
A
Acceleration and deceleration................... 6-2
Air filter elements and check hoses and
V-belt case air filter element ................. 7-19
Fuel..........................................................4-10
Fuel tank cap .............................................4-9
Fuses, replacing ......................................7-33
C
Cables, checking and lubricating ............ 7-28
Canister................................................... 7-14
Care .......................................................... 8-1
Catalytic converter .................................. 4-11
Centerstand and sidestand, checking
and lubricating ...................................... 7-29
Coolant.................................................... 7-18
Cowlings and panels, removing and
installing.................................................. 7-8
D
Dimmer switch .......................................... 4-7
E
Handlebar switches ...................................4-7
Headlight bulb, replacing .........................7-34
High beam indicator light ...........................4-2
Horn switch................................................4-7
I
Identification numbers .............................10-1
Ignition circuit cut-off system ...................4-17
Indicator and warning lights.......................4-2
K
Key identification number ........................10-1
L
Labels, location..........................................1-1
License plate light bulb, replacing ...........7-36
M
Main switch/steering lock...........................4-1
Maintenance and lubrication, periodic .......7-4
Maintenance, emission control system......7-3
Maintenance record.................................10-5
Matte color, caution ...................................8-1
Model label ..............................................10-2
Multi-function display .................................4-3
Engine break-in......................................... 6-3
Engine oil and oil filter element ............... 7-14
Engine stop switch .................................... 4-7
Engine trouble warning light...................... 4-2
N
Final transmission oil .............................. 7-17
Front and rear brake lever free play........ 7-25
Front and rear brake pads, checking ...... 7-26
Front fork, checking ................................ 7-30
R
F
Safe-riding points ...................................... 2-5
Safety defects, reporting ......................... 10-3
Safety information ..................................... 2-1
Seats ....................................................... 4-12
Shock absorber assemblies, adjusting.... 4-16
Sidestand ................................................ 4-16
Spark plug, checking ............................... 7-12
Specifications ............................................ 9-1
Speedometer............................................. 4-2
Starting off ................................................. 6-2
Starting the engine .................................... 6-1
Start switch................................................ 4-7
Steering, checking................................... 7-31
Storage...................................................... 8-3
Storage compartments ............................ 4-14
H
B
Battery..................................................... 7-31
Brake fluid, changing .............................. 7-28
Brake fluid level, checking ...................... 7-27
Brake lever, front....................................... 4-8
Brake lever, rear ....................................... 4-8
Brake levers, lubricating.......................... 7-29
Braking...................................................... 6-3
Rider seat, adjusting ............................... 4-13
S
Noise regulation.......................................10-4
P
Parking ......................................................6-4
Part locations.............................................3-1
Rear brake lock lever.................................4-8
Rear brake lock lever cable, adjusting.....7-26
T
Tachometer ............................................... 4-3
Tail/brake light ......................................... 7-34
Throttle cable free play, checking ........... 7-22
Throttle grip and cable, checking and
lubricating.............................................. 7-29
Tires ........................................................ 7-23
Tool kit....................................................... 7-2
Troubleshooting ...................................... 7-37
Troubleshooting charts............................ 7-38
Turn signal indicator lights ........................ 4-2
Turn signal light bulb (front), replacing .... 7-35
Turn signal light bulb (rear), replacing..... 7-36
Turn signal switch ..................................... 4-7
V
Valve clearance....................................... 7-22
INDEX
Vehicle Emission Control Information
label.......................................................10-2
Vehicle identification number...................10-1
W
Warranty, extended .................................10-9
Warranty, limited......................................10-7
Wheel bearings, checking .......................7-31
Wheels.....................................................7-24
YAMAHA MOTOR CO., LTD.
PRINTED ON RECYCLED PAPER
PRINTED IN JAPAN
2009.05–0.6×1 !
(E)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement