Installation Sheet

FE NIE X . 2016 INSTRUCTION MANUAL
W E B. w w w.feniex.com
Fusion Stick Light- Instruction
Manual
V.1
FUSION
Model # - F-12013, F-22013,
D-50115, D-50215, D-50415,
D-50615, D-50815, D-51015
This instruction manual serves as a
guide for the Fusion Series.
IMPORTANT! Please read through all
provided instructions and any listed
warnings in regards to product use.
Distributed By:
Feniex Product Copyrights This price List and the mentioned Feniex products include or describe copyrighted Feniex material. Laws in the
United States and other countries preserve for Feniex Industries and its licensors certain exclusive rights for copyrighted material, including the
exclusive right to copy, reproduce in any form, distribute and make derivative works of the copyrighted material. Accordingly, any copyrighted
material of Feniex and its licensors contained herein or in the Feniex products described in this Price List may not be copied, reproduced,
distributed, merged or modified,transmitted, transcribed, stored in retrieval system or translated into any language or computer language, in any
form or by any means, without prior written permission of Feniex Industries, Inc.. Feniex and the stylized Feniex logo are registered in the U.S.
Patent & Trademark Office.
Table of Contents
TM
V1.0
Equipment Dimensions
3
Wiring Diagram
4
Flash Patterns
7
Mounting Instructions
9
2
FE NIE X . 2016 INSTRUCTION MANUAL
WE B. w w w.feniex.com
TM
Equipment Dimensions
V1.0
9.5
in.
Fusion 200
1.25in.
2.25in.
18
.82
in.
Fusion 400
1.25in.
2.25in.
28
.14
in.
Fusion 600
1.25in.
37
2.25in.
.46
in.
Fusion 800
64
in.
1.25in.
2.25in.
Fusion Rocker Panel
1.25in.
2.25in.
FE NIE X . 2016 INSTRUCTION MANUAL
W E B. w w w.feniex.com
3
1X, 2X, 100, & 200 Wiring Diagram
TM
V1.0
Fusion 200 Wiring
Fusion 200 System Specification
Wire Color:
Black
Red
Blue
Yellow
Function:
12V (-)
12V (+) Mode 1
Pattern/Sync
Mode 2
Please Note! The Fusion 200 features
four wires: Red [12V+], Black [12V-], White
[12V+], and Green [Flash Pattern Changer].
To change patterns, momentarily connect
the green wire to the activated Black [12V-]
wire. Note that Mode 2 will override Mode 1.
4
FE NIE X . 2016 INSTRUCTION MANUAL
WE B. w w w.feniex.com
TM
400, 600, 800 & Rocker wiring diagram
V1.0
Fusion 400, 600 & 800, Rocker Panel Wiring
Fusion 400, 600, 800 & Rocker Panel
Wiring Diagram
Wire Color:
Black
Single Color:
Dual Color:
12V (-)
12V (-)
12V (+)
12V (+)
Takedown
Takedown/Flood
Flash Mode
Flash Mode
Green
Takedown Flashing*
Mode Two
Brown
Left Arrow
Left Arrow
Lightbar On
Mode One
Right Arrow
Right Arrow
Center Out
Center Out
Red
White
Yellow
Blue
Gray
Blue/Gray
*Please Note! These modes only function when the unit has takedowns in the assembly.
FE NIE X . 2016 INSTRUCTION MANUAL
W E B. w w w.feniex.com
5
400, 600, 800 & Rocker wiring instructions
Step 1: In order to power the unit, extend
the red, 12V(+) wire to the 12V(+) post of
the vehicle’s battery. Extend the black
12V(-) wire to the ground post of the
vehicle’s battery.
Step 2: To turn the lightstick on, connect
the brown wire to a 12V(+) source.
Step 3: Momentarily connect the yellow wire
on a 12V(+) source to change flash patterns.
Step 4: For left arrow function, connect the
blue wire to a 12V(+) post (switch). There are
2 different left arrow flash patterns. To select
a pattern, engage the blue wire to a 12V(+)
source and momentarily connect the yellow
wire on a 12V(+) source to select the desired
pattern.
TM
V1.0
Step 5: For right arrow function, connect
the gray wire to a 12V(+) post (switch). There
are 2 different right arrow flash patterns.
To select a pattern, engage the gray wire a
12V(+) source and momentarily connect the
yellow wire on a 12V(+) source to select the
desired pattern.
Step 6: In order to achieve a center out directional
pattern, connect both the gray and blue wires to a
12V(+) post (switch). There are 2 different center
out flash patterns. To select a pattern, engage
the blue and gray wire to a 12V(+) source and
momentarily connect the yellow wire on a 12V(+)
source to select the desired pattern.
Step 7: For takedown steady functionality,
connect the white wire to a 12V(+) post (switch).
Step 8: For takedown flashing, connect the green
wire to a 12V+ (post). Please note that for dual
color bars, the green wire will activate mode 2,
unless otherwise programmed.
Important Note! Takedown steady overrides
takedown flashing
Activate Takedown Flashing for Dual Color:
Step 1: Connect the black wire to the
battery’s 12V(-) ground.
Step 2: Select the wire that will be set as
the takedown flashing mode wire, either
the green or brown wire.
Step 3: Twist the selected mode (green
or brown), red, white, and yellow wires
together.
6
FE NIE X . 2016 INSTRUCTION MANUAL
WE B. w w w.feniex.com
Step 4: Power the lightbar on by
connecting the twisted wires to the
battery’s positive (+). Once activated, the
takedown steady function will engage. To
verify takedowns are flashing, disconnect
Takedown Steady (white) wire from power.
Step 5: Repeat steps 1 through 3 to
deactivate Takedown Flashing.
TM
Flash Patterns
V1.0
The flash patterns are listed in consecutive order of appearance. To select a certain flash
pattern, start with a recognizable pattern and use the blue wire to cycle through patterns.
Flash Patterns Single Color:
Fusion 400, 600, 800 & Rocker Panel
Flash Patterns Dual Color:
Fusion 200, 400, 600, 800 & Rocker Panel
2.
2.
1.
Cluster
3.
Night Rode
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
Attack
Combo Slow-Fast
Combo Slow
Combo Fast
Half Half Slow
Half Half Fast
One One Slow
One One Fast
Two Two Slow
Two Two Fast
All On Slow
All On Fast
In Out Slow
In Out Fast
Left Arrow Slow
Left Arrow Medium
Left Arrow Fast
Right Arrow Slow
Right Arrow Medium
Right Arrow Fast
Center Out Slow
Center Out Medium
Center Out Fast
1.
Color 1-Cluster
3.
Color 1-Night Ride
4.
5.
6.
7.
8.
9.
Color 1-Attack
Color 1-Combo Slow-Fast
Color 1-Combo Slow
Color 1-Combo Fast
Color 1-Half Half Slow
Color 1-Half Half Fast
Color 1-One One Slow
10. Color 1-One One Fast
11. Color 1-Two Two Slow
12. Color 1-Two Two Fast
13. Color 1-All On Slow
14. Color 1-All On Fast
15. Color 1-In Out Slow
16. Color 1-In Out Fast
17. Color 1-Left Arrow Slow
18. Color 1-Left Arrow Medium
19. Color 1-Left Arrow Fast
20. Color 1-Right Arrow Slow
21. Color 1-Right Arrow Medium
22. Color 1-Right Arrow Fast
23. Color 1-Center Out Slow
24. Color 1-Center Out Medium
25. Color 1-Center Out Fast
26. Color 2-Cluster
27. Color 2-Attack
28. Color 2-Night Ride
29. Color 2-Combo Slow-Fast
30. Color 2-Combo Slow
31. Color 2-Combo Fast
32. Color 2-Half Half Slow
FE NIE X . 2016 INSTRUCTION MANUAL
W E B. w w w.feniex.com
7
TM
Flash Patterns
Flash Patterns Dual Color:
Fusion 200, 400, 600, 800 & Rocker Panel
33. Color 2-Half Half Fast
34. Color 2-One One Slow
35. Color 2-One One Fast
36. Color 2-Two Two Slow
37. Color 2-Two Two Fast
38. Color 2-All On Slow
39. Color 2-All On Fast
40. Color 2-In Out Slow
41. Color 2-In Out Fast
42. Color 2-Left Arrow Slow
43. Color 2-Left Arrow Medium
44. Color 2-Left Arrow Fast
45. Color 2-Right Arrow Slow
46. Color 2-Right Arrow Medium
47. Color 2-Right Arrow Fast
48. Color 2-Center Out Slow
49. Color 2-Center Out Medium
50. Color 2-Center Out Fast
51. Color 1&2-Cluster
52. Color 1&2-Attack
53. Color 1&2-Night Ride
54. Color 1&2-Combo Slow-Fast
55. Color 1&2-Combo Slow
56. Color 1&2-Combo Fast
57. Color 1&2-Half Half Slow
58. Color 1&2-Half Half Fast
59. Color 1&2-One One Slow
60. Color 1&2-One One Fast
61. Color 1&2-Two Two Slow
62. Color 1&2-Two Two Fast
63. Color 1&2-All On Slow
64. Color 1&2-All On Fast
8
FE NIE X . 2016 INSTRUCTION MANUAL
WE B. w w w.feniex.com
V1.0
Flash Patterns Dual Color:
Fusion 200, 400, 600, 800 & Rocker Panel
65. Color 1&2-In Out Slow
66. Color 1&2-In Out Fast
67. Color 1&2-Left Arrow Slow
68. Color 1&2-Left Arrow Medium
69. Color 1&2-Left Arrow Fast
70. Color 1&2-Right Arrow Slow
71. Color 1&2-Right Arrow Medium
72. Color 1&2-Right Arrow Fast
73. Color 1&2-Center Out Slow
74. Color 1&2-Center Out Medium
75. Color 1&2-Center Out Fast
TM
Mounting
V1.0
Step 1: To mount to bracketry, remove
the flat endcap and slide in provided bolts
in the back of the frame. Screw the flat
endcap back into the aluminum extrusion
with the original screws and attach bolts
and nuts with the brackets.
Step 2: Mark the areas where the mounting
holes will be drilled. If mounting surface
is part of the vehicle, make sure no vital
components could be damaged by the
drilling process.
Step 3: Drill two mounting holes in the
marked surface. If wires need to pass
through vehicle, drill a 0.5” diameter hole
for wire passage. Make sure to deburr
holes thoroughly.
Step 4: Pass the wires through the 0.5”
diameter hole, and secure the lighthead
to the mounting surface with the provided
hardware.
1
Figure 5.0
2
3
Item #:
1.
Description:
Cobra Extrusion
2.
Mounting Hardware
3.
Mounting Bracket
3
FE NIE X . 2016 INSTRUCTION MANUAL
W E B. w w w.feniex.com
9