Lionel NYC Flyer Set - 6/01 Owner's Manual
Lionel NYC Flyer Set - 6/01 has a RailSounds sound system that gives you the realistic sounds of a steam locomotive, along with the capability to add smoke fluid that creates realistic smoke. It runs on O-27 gauge track, making it compatible with other sets that may be used in the layout. In addition to the locomotive, the set includes a tender, a boxcar, a flatcar with stakes, and a caboose, all of which can be attached to the locomotive to create a train.
Advertisement
Advertisement
73-1914-250
6/01
N E W Y O R K
S Y S T E M
New York Central Flyer
Ready-To-Run O-27 Set
Owner’s Manual
CAUTION—ELECTRIC TOY
NOT RECOMMENDED FOR CHILDREN UNDER EIGHT YEARS OF AGE. AS WITH
ALL ELECTRIC PRODUCTS, PRECAUTIONS SHOULD BE OBSERVED DURING
HANDLING AND USE TO REDUCE THE RISK OF ELECTRIC SHOCK.
TRANSFORMER RATINGS—INPUT: 120 VAC; 60 HZ ONLY.
AC OUTPUT: 20 V; 54 VA
Congratulations!
Y ou’re now the proud owner of the New
York Central Flyer ready-to-run O-27 train set. Everything you need to get started is included. You’re already off to a great start by reading this instruction manual. It has important information on train setup and operation. This booklet also covers proper maintenance procedures to help your
Lionel trains live long, healthy lives.
If you have any questions after reading this booklet, contact your nearest Lionel
Authorized Service Center using the list included in a separate flier in this set or call
Lionel Service at 810-949-4100. And have fun!
Table of contents
Track layout
Getting started
Joining the track sections
Suggested track layouts
Attaching the lockon to the track
Controller operations
Stripping the wire
Attaching the controller wires to the lockon
Controller functions
Controller and short circuits
Installing the Lionel Sound Activation Switch
Train operation
Reverse unit procedure
Tire-Traction™
Coupling
Your lomotive’s RailSounds system—the basics
Experiencing the range of your locomotives’s RailSounds system
Notes on RailSounds
Maintaining and servicing your set
Lubricating your 4-4-2 locomotive
Adding smoke fluid to your 4-4-2’s smoke generator
Replacing your 4-4-2’s headlamp
Assembling your flatcar with bulkhead and stakes
Lionel Service
4
4
3
3
6
7
5
5
8
13
13
14
15
16
9
10
10
11
12
12
2
Track layout
Getting started
B efore you do anything else, we recommend you check the contents of your set box to ensure all of the parts of your set have been included and that the quantities
(when applicable) are correct.
The parts list below will tell you what’s
• NYC Flyer 4-4-2 locomotive
• NYC Flyer tender w/RailSounds
• Boxcar
• Flatcar w/bulkheads and
10 stakes
• NYC caboose
• Smoke fluid
• Crate load
• Controller
1
1
1
1
1
1
2
1 included and the correct quantities. If you find any discrepancies, contact the dealer you purchased your set from for more information or call 1-800-4-LIONEL for a Service
Center near you.
• 40-watt power pack
• Lockon
• Straight track
• Curved track
• Service Center list
• Railroader Club application
• Warranty Card
• Sound Activation Switch
(610-5905-001)
1
1
1
8
8
1
1
1
Now comes the fun part—deciding what kind of layout you want. The only rule— let your imagination be your guide.
Joining the track sections
J oin the track sections together by inserting the pins of one track section into the rail openings of another.
For good electrical contact, pins must be carefully inserted and track joints tightly fitted.
If the track is difficult to connect, try this installation tip. You can “break in” O-27 track sections by inserting and withdrawing a track pin into one rail at a time before joining the entire track section.
If the openings become too wide (causing the track to fit loosely), pinch the rail together around a track pin with a pair of pliers. If any pins fall out of the track and are missing, replace them with extras available from your
Lionel dealer.
Maintenance tip: The rails should be kept clean, dry, and free from oil and grease. Clean rust and dirt spots with a track eraser. Wipe the track using a cloth dampened with track cleaner from the Lionel maintenance kit
(no. 6-62927), available from your nearest
Lionel Authorized Value Added Dealer or
Lionel Service.
3
Track layout
Suggested track layouts
Here are some examples of layouts you can build with 8 straight and 8 curved sections of track.
Remember—the more track you own, the more variations you can create in your train layout.
And that means more action and more fun!
Attaching the lockon to the track
T he lockon connects power from your controller to the track. Attaching the lockon to the track is quick and easy.
First, place the lockon under any straight section of track. Fit the center lip of the lockon onto the edge of an outside rail. Press the
1
2
LIONEL
CTC
LOCKON lockon upward so that the spring contact snaps onto the center rail. The lockon should face outward when setting up your track and make sure it is firmly connected.
Use the illustrations below as a step-bystep guide.
Once the lockon is securely attached to the track, it’s time to insert the wires from the controller into the two spring clips on the lockon. See page 5 for easyto-follow steps.
2
Snap spring contact to the middle rail
1
Hook lip to the outside of the rail
4
Controller operations
Stripping the wire
O nce your track is assembled and the lockon is securely attached, you can connect the wires from the controller to the lockon.
First you’ll want to check the ends of the wires to make sure that the insulation is stripped back about 1⁄4˝ to 3⁄8˝. To strip the wires, use a pair of wire strippers or a sharp knife.
Caution: Only an adult should perform this task! Always use care when stripping wires.
Attaching the controller wires to the lockon
N ow you’ll need to insert a controller wire into each of the two spring clips on the lockon.
It’s easy! Depress the spring clip with your finger and insert the bare end of the wire into the exposed opening. Release the spring clip. Give the wire a little tug to make sure it’s secure. Repeat these steps with the other spring clip. Next, insert the small plug end of the power pack into the back of your controller, and plug the other end into a standard outlet.
Note!
If the whistle fails to operate when you press the whistle button on your controller (see page
6), remove the wires from the lockon and reinsert each one into the opposite clip to reverse polarity.
Plug power pack into standard wall outlet
Make sure that the bare end of each wire is securely attached to the spring clip.
5
R
OFF
FULL
SPEED
Plug this end into back of controller.
Controller operations
Controller functions
A s you turn the throttle control knob to the right, power to the track is increased. When the indicator reaches the green band, there should be sufficient power to operate the locomotive. The further into the green area the knob is turned, the faster your train will go. Remember that the greater the load on the engine (adding more cars for the engine to pull, for example), the farther into the green the knob must be turned before it will operate the locomotive.
The yellow band indicates the average power range that the train will be operating in. The red band represents maximum power output.
Press this button to produce a realistic whistle or bell sound.
(See page 8.)
Press this button to go forward or reverse, or to place the locomotive in
“neutral” (no movement, headlight is on).
Turn the throttle control knob to the right for more power.
R
The LED indicator shows when your controller is ON.
Green band
Yellow band
Red band
6
Controller operations
Controller and short circuits
Y our Lionel power pack is listed by
Underwriters Laboratories Inc. and has been carefully designed and tested to ensure peak performance. The controller is equipped with a built-in electronic circuit breaker that alternately cuts off and restores the flow of power to the track whenever a short circuit exists—for example, when the train derails. The circuit breaker’s action continues until the cause of the short circuit is eliminated. This circuit breaker is incorporated into the controller to protect it from possible damage. It will not protect the locomotive or electrically operated accessories, so it’s important to eliminate short circuits as soon as possible.
Note!
The power pack must be unplugged from the wall socket when a short circuit is noticed, and the short circuit must be corrected.
A short circuit is caused by a direct connection between the center rail and one of the outside rails or by a direct connection between bare wires. The axles of a derailed car or locomotive are the most frequent cause of short circuits, so make sure that all wheels are properly set on the rails. Some other causes of short circuits might be staples, nails, paper clips, or other metallic objects lying across the rails, or two bare wires touching each other.
If too many cars or accessories are used, your controller will exceed its power limit and begin to cycle on and off. To correct this problem, cars or accessories must be removed before normal operation can resume. For more power, see the line of
Lionel high-output transformers at your
Authorized Lionel Value Added Dealer.
The same condition can occur if the power is turned up too quickly. This also could cause your train to move too fast and derail.
After your power pack has been operating for a while, you will find it warm to the touch. It is the nature of all electrical power equipment to become warm when in use. If your controller is loaded to capacity, it is a good idea to let it cool down after an hour or two of continuous use. Unplug the power pack from the wall when the controller is not in use.
7
Controller operations
Installing the Lionel Sound Activation Switch
T o operate the bell and whistle sounds when operating your steam locomotive with conventional transformers, you’ll need to install the Lionel no. 610-5905-001 sound activation switch. Connect the switch as shown below.
Wires from Transformer
To Track
Note!
If the whistle and bell icons are reversed during operation, simply switch the wires on the lockon.
8
Train operation
Reverse unit procedure
T he reverse unit inside your Lionel locomotive is an electronic device that acts like the transmission in your car. When you in the sequence. For instance, if the locomotive is moving forward, then is stopped and apply power to the track, the locomotive moves in the direction specified by the reverse unit—or it sits in neutral, awaiting another power interruption. Power interrupthe switch is thrown back, the locomotive will be “locked” in neutral. If the switch is thrown back while the locomotive is under power, the locomotive will remain in the tions are the signal that tells the reverse unit to sequence to the next operational state. mode it was in when the switch was thrown.
The controller direction control will then have no affect on the direction of
To interrupt power and sequence the locomotive’s reverse unit, press the direction conthe locomotive.
Additionally, this reverse unit has a
“power-up reset” feature, which means that should trol button or turn the throttle to the OFF position and ON again. The
Reverse unit ON/OFF switch reverse unit alternates between three states: the locomotive sit without power for a short period of time (less than
10 seconds), the reverse unit will automatiforward, neutral, and reverse.
Also, the locomotive can be “locked” into a certain mode of operation by throwing the switch located on the underside of the frame
(see illustration above). When the switch is thrown to the OFF position, the locomotive will be locked in the next mode of operation cally reset and start in the forward direction when the transformer is turned on or “powered up,” regardless of the locking switch position. If the locking switch is in the Off position, the locomotive will start in the forward direction and be “locked” there.
R
Whistle/Bell control button
Direction control button
FULL
SPEED
9
Train operation
Tire-Traction™
Y our locomotive is equipped with Tire-
Traction. This means that one of the drive wheels is fitted with a rubber traction tire to enhance tractive effort so your locomotive can pull many cars at once.
Lionel locomotives with Tire-Traction grip the track, enabling them to pull heavy loads at higher speeds.
Coupling
A fter you have assembled the track, place the locomotive and rolling stock on the track. Before coupling the cars, make sure the wheels are properly set on the rails.
When coupling your cars, at least one of the mating couplers must be open as shown below at the left. Now simply push the cars toward each other until they lock together.
Now you’re ready to pull out of the station. All aboard!
Push down the lock release to open the coupler.
Keep in mind that it’s easier to couple cars on a straight stretch of track.
10
Train operation
Your Locomotive’s RailSounds system—the basics
L ionel RailSounds are the most realistic model railroad sound system in the world. Your locomotive RailSounds features digital samples for the ultimate in realism.
Begin by installing a 9-volt alkaline battery in the tender. This ensures interruption free operation of RailSounds. Remove the tender body, refer to the diagram below.
Connect the 9-volt alkaline battery to the battery clip (remove the protective cover from the battery clip), and place the battery in the holder inside the tender.
When you first apply track power, the locomotive’s RailSounds system delivers an authentic start-up sequence, followed by the sounds of the locomotive at idle. As the locomotive’s speed increases, the chuff rate will increase too.
1 Remove the tender body
3 Place the battery in the holder inside the tender
2 Remove the protective cover from the battery clip and connect the 9-volt alkaline battery
Note!
Although RailSounds is powered by track voltage, the battery is required for uninterrupted operation and shutdown sequences. Use only alkaline batteries.
Note!
If RailSounds “drops out” during track power interrupts (direction change), replace the battery.
11
Train operation
Experiencing the range of your locomotive’s RailSounds system
W ith RailSounds, you experience the sounds of real railroading like never before. Simply put, it’s the most sophisticated, authentic model railroad sound system in the world.
• Variable chuff rate. Your
Locomotive’s speed determines the steam chuff rate.
• MultiWhistle/Bell. These features can be activated by setting the Sound
Activation Switch (page 8) and pressing the whistle/bell button on your
Controller (page 6). If the bell is chosen on the switch, it will begin when you push the whistle/bell button and discontinue when you push it again.
• Shutdown sequence. No other model railroad sound system shuts down like
RailSounds. Turn off track power, and after the air-release reset sound, you have two seconds to restart your
Locomotive. If you’re done with operations, RailSounds will commence with an authentic shutdown sequence about two seconds after the air-release reset occurs.
• Braking Sounds. To activate the screeching sound of your locomotive’s brakes, simply turn the controller down as the engine is moving. Notice the sound becomes more intense the faster your engine is moving and the greater its deceleration. This can also be accomplished by pressing the direction button while the train is in motion.
NOTE: Battery must be installed for shutdown sequence.
Notes on RailSounds
• Use the volume control dial, located on the underside of the tender frame. Turn the volume set screw clockwise (up) or counter clockwise (down) to adjust the volume.
• Listen for incidental Locomotive sounds during RailSounds operation. They’re automatic and, of course, authentic.
• The 9-volt alkaline battery you installed ensures continuous sounds, even during short track-power interrupts.
• Longer track-power interruptions
(including locomotive derailments) cause RailSounds to shut down after about 7 seconds.
12
Maintaining and servicing your set
Lubricating your 4-4-2 locomotive
H elp your 4-4-2 steam locomotive lead a long and productive life on your railroad by maintaining it properly.
We recommend you purchase a Lionel
Lubrication and Maintenance Kit (no. 6-
62927), available from your Lionel dealer.
Two basic rules to keep in mind: Never overlubricate (a small amount will do), and avoid getting grease or oil on the 4-4-2’s wheels, contact rollers, or your track.
You’ll know your 4-4-2 requires lubrication when visual inspection reveals dryness on the parts indicated in the illustration.
Remove accumulated dirt and dust before lubricating, and always lubricate any locomotive emerging from prolonged storage.
Lubricate axle ends with Lionel oil sparingly
Lubricate with
Lionel oil sparingly
Lubricate gears with
Lionel grease sparingly
Adding smoke fluid to your 4-4-2’s smoke generator
Y our 4-4-2 locomotive is equipped with a smoke generator that produces safe, clean white smoke during operation.
The smoke generator requires the periodic addition of Lionel smoke fluid in order to function. Pierce the smoke fluid tube end with a pin, then add
4 to 8 drops of fluid directly into the locomotive’s stack.
Smoke production commences momentarily, faster if you run your locomotive at high speed. When smoke production wanes, add more fluid (4 to 8 drops). An idle locomotive
13 will not smoke. NOTE: Always keep a small amount of smoke fluid in the locomotive’s smoke generator; the generator’s element can become damaged if operated without smoke fluid. This is particularly true if your locomotive sits in neutral for an extended period of time without smoke fluid in the generator.
Smoke production is greater at higher voltages and when the locomotive is pulling a heavy load or a long consist.
Maintaining and servicing your set
Replacing your 4-4-2 locomotive’s headlamp
Y our 4-4-2 locomotive lights the way with headlamp illumination. During the course of normal operation, the lamp may require replacement.
First remove the two front truck screws and carefully slide the front truck assembly off the linkage rods. Lift the smoke unit out far enough from the cab to allow lamp extraction. Pull the lamp straight out and replace it with Lionel part no. 600-0161-
300, available from your nearest Lionel
Authorized Service Center or from Lionel
Service. Be careful not to twist the lamp or it may break.
Now, reinstall the smoke unit, making sure that the smoke stack lines up with the cab top opening. Reassemble the front truck, making sure that the linkage rods go into the holes in the front truck. The lug wire from the smoke unit must be reinserted through the slot in the front truck assembly and secured under one of the two front screws. Tighten the screws firmly but do not over tighten.
Smoke unit
Linkage rods
Front truck screws
Lamp
Lionel part no.
600-0161-300
Smoke unit lug wire
14
Maintaining and servicing your set
Assembling your flatcar with bulkhead and stakes
Y our flatcar with stakes will require some assembly before it’s ready to roll.
Remove the 10 stakes supplied with this car and carefully press them into the corresponding slots as shown below.
Now, insert the two bulkheads onto either end of the flatcar in the slots provided.
You’ll notice that there is one open slot on either end of the flatcar. This is normal and these slots should remain open.
Open slot
Bulkhead
Open slot
Bulkhead
10 stakes
15
Limited Warranty/Lionel Service
T his Lionel product, including all mechanical and electrical components, moving parts, motors and structural components, except for light bulbs, is warranted to the original consumer-purchaser, for one year against original defects in materials or workmanship when purchased through an authorized Lionel dealer.
This warranty does NOT cover normal wear and tear, light bulbs, defects appearing in the course of commercial use, or damage resulting from abuse or misuse of the product by the purchaser. Transfer of this product by the original consumer-purchaser to another person voids this warranty. Modification of this product voids this warranty.
Any warranted product which is defective in original materials or workmanship and is delivered by the original consumer-purchaser to
Lionel L.L.C. or an authorized Lionel L.L.C. Service
Station, together with proof of original purchase will, at the option of Lionel L.L.C., be repaired or replaced, without charge for parts or labor. In the event the defective product cannot be repaired, and a replacement is not available, a refund of the original purchase price will be granted. Any products on which warranty service is sought must be sent freight or postage prepaid, as transportation and shipping charges are not covered by the warranty.
In no event shall Lionel L.L.C. be liable for incidental or consequential damages.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion may not apply to you.
This limited warranty gives you specific legal rights, and you may have other rights which vary from state to state.
Instructions for Obtaining Service
If service for this Lionel L.L.C. product is required, bring the item, along with your dated sales receipt and completed warranty information to the nearest Authorized Lionel Service Station.
Your nearest Lionel Service Station can be found by calling 1-800-4-Lionel, or by accessing our
Website at www.lionel.com.
If you prefer to send your product back to
Lionel L.L.C. for factory repair, you must first call
810-949-4100 or FAX 810-949-5429, or write to
Customer Service, P.O. Box 748, New Baltimore,
MI 48047-0748, stating what the item is, when it was purchased and what seems to be the problem.
You will be sent a return authorization letter and label to ensure your merchandise will be properly handled upon receipt.
Once you have received your return authorization and label, make sure that the item is packed to prevent damage during shipping and handling. We suggest that you use the product’s original packaging. This shipment must be prepaid and we recommend that it be insured.
Please make sure you have followed all of the above instructions carefully before returning any merchandise for service.
Warranty Information
Please complete the information below and keep it, along with your dated sales receipt. You must present this and your dated sales receipt when requesting warranty service.
Name ____________________________
Address ____________________________
Place of Purchase ____________________
Date of Purchase ____________________
Product Number ______________________
Product Description____________________
_________________________________
©2001 L
IONEL
LLC, C
HESTERFIELD
, MI 48051-1956
U NITED S TATES OF A MERICA
P
RINTED IN
C
HINA
Advertisement