Manual TSC TTP
TTP-244 Pro Series
THERMAL TRANSFER / DIRECT THERMAL
BAR CODE PRINTER
USER’S
MANUAL
Copyright Information
© 2014 TSC Auto ID Technology Co., Ltd.
The copyright in this manual, the software and firmware in the printer described
therein are owned by TSC Auto ID Technology Co., Ltd., All rights reserved.
CG Triumvirate is a trademark of Agfa Corporation. CG Triumvirate Bold
Condensed font is under license from the Monotype Corporation. Windows is a
registered trademark of Microsoft Corporation.
All other trademarks are the property of their respective owners.
Information in this document is subject to change without notice and does not
represent a commitment on the part of TSC Auto ID Technology Co. No part of
this manual may be reproduced or transmitted in any form or by any means, for
any purpose other than the purchaser’s personal use, without the expressed
written permission of TSC Auto ID Technology Co.
Agency Compliance and Approvals
EN 55022, Class A
EN 55024
EN 60950-1
FCC part 15B, Class A
AS/NZS CISPR 22, Class A
EN 60950-1
GB 4943.1
GB 9254
GB 17625.1
Wichtige Sicherheits-Hinweise
1. Bitte lesen Sie diese Hinweis sorgfältig durch.
2. Heben Sie diese Anleitung fűr den späteren Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromentz zu trennen. Verwenden Sie keine Flüssig-oder
Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung.
4. Die Netzanschluß -Steckdose soll nahe dem Gerät angebracht und leicht zugänglich sein.
5. Das Gerät ist vor Feuchtigkeit zu schűtzen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen könnte
Beschädigungen hervorrufen.
7. Beachten Sie beim Anschluß ans Stromnetz die Anschluß werte.
8. Dieses Gerät kann bis zu einer Auß entemperatur von maximal 40℃ betrieben werden.
CAUTION
1. HAZARDOUS MOVING PARTS IN CUTTER MODULE. KEEP FINGER AND OTHER BODY PARTS AWAY.
2. THE MAIN BOARD INCLUDES REAL TIME CLOCK FEATURE HAS LITHIUM BATTERY CR2032 INSTALLED.
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
3. DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER INSTRUCTIONS.
“VORSICHT”
Explosionsgefahr bei unsachgemäß en Austausch der Batterie. Ersatz nur durch
denselben oder einem vom Hersteller empfohlenem ähnlichen Typ. Entsorgung
gebrauchter Batterien nach Angaben des Herstellers.
- ii -
CE WARNING:
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
FCC WARNING:
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may
cause harmful interference with radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference, in which
case you will be required to correct the interference at your own expense.
IC WARNING (AVERTISSEMENT):
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conform à la norme NMB-003 du Canada.
CCC 警告:
此为 A 级产品,在生活环境中,该产品可能会造成无线电干扰。在这种情况下,可能需要用户对干扰采
取切实可行的措施。
A 급기기
(업무용 정보통신기기)
이 기기는 업무용으로 전자파 적합등록을 한 기기이오니, 판매자 또는 사용자는 이 점을 주위하시기
바라며, 만약 잘못 판매 또는 구입하였을 때에는 가정용으로 교환하시기 바랍니다.
- iii -
Contents
1. Introduction............................................................................................................. 1
1.1 Product Introduction ......................................................................................... 1
1.2 Product Features .............................................................................................. 2
1.2.1 Printer Standard Features ................................................................................................ 2
1.2.2 Printer Optional Features ................................................................................................. 3
1.3 General Specifications...................................................................................... 4
1.4 Print Specifications ........................................................................................... 4
1.5 Ribbon Specifications ....................................................................................... 4
1.6 Media Specifications ........................................................................................ 6
1.7 Various Sensor ................................................................................................. 7
2. Operations Overview .............................................................................................. 9
2.1 Unpacking and Inspection ................................................................................ 9
2.2 Printer Overview ............................................................................................. 10
2.2.1 Front View ........................................................................................................................ 10
2.2.2 Interior View ..................................................................................................................... 11
2.2.3 Rear View ......................................................................................................................... 12
2.3 LED Indicators and Buttons ............................................................................ 13
2.3.1 LED Indication ................................................................................................................. 13
2.3.2 Buttons ............................................................................................................................. 13
3. Setup .................................................................................................................... 14
3.1 Setting up the Printer ...................................................................................... 14
3.2 Loading the Media .......................................................................................... 15
3.3 Loading the Ribbon ........................................................................................ 17
3.4 Install SD Memory Card (Option) ................................................................... 20
4. Using Printer......................................................................................................... 22
4.1 Power-on Utilities ........................................................................................... 22
4.1.1 Self Test and Dump Mode .............................................................................................. 22
4.1.2 Gap Sensor Calibration Utility ....................................................................................... 24
4.1.3 Printer Initialization ......................................................................................................... 25
5. Diagnostic Tool..................................................................................................... 27
- iv -
5.1 Start the Diagnostic Tool ................................................................................ 27
5.2 Printer Function .............................................................................................. 28
6. Troubleshooting.................................................................................................... 29
7. Maintenance ......................................................................................................... 30
Revise History .......................................................................................................... 31
-v-
1. Introduction
1.1 Product Introduction
Thank you very much for purchasing TSC bar code printer.
The TTP-244 Pro offers the largest media and ribbon capacities in its class. Unlike most
printers, it can easily handle both a 300-meter ribbon and a full 8-inch OD roll of labels.
With its fast 5 inch per second print speed, along with the largest memory capacity in its
class, the TTP-244 Pro easily outperforms the competition.
With its small, compact footprint and dual-motor design, the TTP-244 Pro is perfect for a
wide variety of label and tag printing applications – everything from shipping labels to
compliance and general purpose product-identification labels & tags.
The TTP-244 Pro supports PDF417, QRCode, Datamatrix …. two-dimensional barcodes
used to print complex transportation formats – a feature that makes it ideal for automobile
service shops, stock rooms, and walk-in shipping and mail centers.
To print label formats, please refer to the instructions provided with your labeling software;
if you need to write the custom programs, please refer to the TSPL/TSPL2 programming
manual that can be found on the accessories CD-ROM or on TSC website at
http://www.tscprinters.com.
− Applications

Shipping and receiving

Compliance labeling

Asset tracking

Inventory control

Document management


Shelf labeling and product marking
Specimen labeling and patient tracking
1.2 Product Features
1.2.1 Printer Standard Features
The printer offers the following standard features.
Product standard feature
Thermal transfer or direct thermal printing
Black mark reflective sensor
Gap transmissive sensor
Ribbon end sensor
2 buttons
3 LED for printer status (Power, Error, On-line)
32-bit RISC CPU
USB 2.0 (full speed) & RS-232 interface
8 MB SDRAM memory
4 MB FLASH memory
Eltron® EPL and Zebra® ZPL emulation languages support
Internal 8 alpha-numeric bitmap fonts
Internal Monotype Imaging® true type font engine with one CG Triumvirate Bold
Condensed scalable font
Fonts and bar codes can be printed in any one of the four directions (0, 90,180,
270 degree)
Downloadable fonts from PC to printer memory
Downloadable firmware upgrades
Bar code, graphics/image printing
Supported bar code
Supported image
1D bar code
2D bar code
Code 39, Code 93, Code 128UCC,
Code 128 subset A, B, C, Codabar,
Interleave 2 of 5, EAN-8, EAN-13,
EAN-128, UPC-A, UPC-E, EAN and
UPC 2 (5) digits add-on, MSI,
PLESSEY, POSTNET, RSSStacked, GS1 DataBar, Code 11
DataMatrix,
Maxicode, PDF-417,
Aztec, QR code
-2-
BITMAP, BMP, PCX
(Max. 256 colors
graphics)
Code page







































Codepage 437 (English - US)
Codepage 737 (Greek)
Codepage 850 (Latin-1)
Codepage 852 (Latin-2)
Codepage 855 (Cyrillic)
Codepage 857 (Turkish)
Codepage 860 (Portuguese)
Codepage 861 (Icelandic)
Codepage 862 (Hebrew)
Codepage 863 (French Canadian)
Codepage 864 (Arabic)
Codepage 865 (Nordic)
Codepage 866 (Russian)
Codepage 869 (Greek 2)
Codepage 950 (Traditional Chinese)
Codepage 936 (Simplified Chinese)
Codepage 932 (Japanese)
Codepage 949 (Korean)
Codepage 1250 (Latin-2)
Codepage 1251 (Cyrillic)
Codepage 1252 (Latin-1)
Codepage 1253 (Greek)
Codepage 1254 (Turkish)
Codepage 1255 (Hebrew)
Codepage 1256 (Arabic)
Codepage 1257 (Baltic)
Codepage 1258 (Vietnam)
ISO-8859-1: Latin-1 (Western European)
ISO-8859-2: Latin-2 (Central European)
ISO-8859-3: Latin-3 (South European)
ISO-8859-4: Latin-4 (North European)
ISO-8859-5: Cyrillic
ISO-8859-6: Arabic
ISO-8859-7: Greek
ISO-8859-8: Hebrew
ISO-8859-9: Turkish
ISO-8859-10: Nordic
ISO-8859-15: Latin-9
UTF-8
1.2.2 Printer Optional Features
The printer offers the following optional features.
User
option
Product option feature
Centronics parallel & RS-232 serial interfaces or
Centronics parallel & USB serial interfaces
Bluetooth module (serial interface)
802.11 b/g/n wireless module (serial interface)
External roll mount, media OD. 214 mm (8.4”) on a 1” or
3” core
-3-
Factory
option
○
○
○
○
SD card reader for memory expansion up to 4G
3” core label spindle
KP-200 Plus keyboard
KU-007 Plus programmable smart keyboard
○
○
○
○
1.3 General Specifications
General Specifications
Physical
dimensions
Enclosure
Weight
Power
Environmental
condition
Environmental
concern
232 mm (W) x 156 mm (H) x 288 mm (D)
ABS plastic
2.5 kg (5.51 lbs)
External universal switching power supply
Input: AC 100-240V, 2.5A, 50-60Hz
Output: DC 24V, 2.5A, 60W
Operation: 5 ~ 40°C, 25 ~ 85% non-condensing
Storage: -40 ~ 60°C, 10~ 90% non-condensing
Comply with RoHS, WEEE
1.4 Print Specifications
Print Specifications
Print head resolution
(dots per inch/mm)
Printing method
Dot size
(width x length)
Max.print speed
Max. print width
Max. print length
203 dots/inch (8 dots/mm)
Thermal transfer or direct thermal
0.125 x 0.125 mm
(1 mm = 8 dots)
5 ips (127 mm/sec)
4.25” (108 mm)
90” (2286 mm)
1.5 Ribbon Specifications
Ribbon Specifications
Ribbon outside diameter
Max. 67 mm OD
-4-
Ribbon length
Ribbon core inside
diameter
Ribbon width
300 m
Ribbon wound type
Ink coated outside
1” core
40 mm ~ 110 mm (1.6” ~ 4.3”)
Note: The maximum length of ribbon depends on its thickness and core outside diameter.
The formula below defines the correlation between ribbon roll length and ribbon core diameter.
L=
(D 2  d 2 )  
, where
4t
L = Ribbon length
D = Max. roll diameter
d = Ribbon core outside diameter
t = Ribbon thickness
-5-
1.6 Media Specifications
Media Specifications
Label roll capacity
Media core diameter
Media wound type
110 mm (4.33”) OD
25.4 ~ 76.2 mm (1” ~ 3”)
Continuous, die-cut, black mark, External fanfold, notched
Outside wound
Media width
Media thickness
Label length
25.4 ~ 112 mm (1.0” ~ 4.4”)
0.06 ~ 0.25 mm (2.36 ~ 9.84 mil)
10 ~ 2,286 mm (0.39” ~ 90”)
Media type
-6-
1.7 Various Sensor
Gap Sensor
The gap sensor detects a label gap to locate the top of form of the next label. The sensor is
mounted 4 mm off the center line of the main mechanism.
.
In case of Label
Black Mark Sensor
The black mark sensor locates the position of label by emitting infrared rays onto the black
mark at the back of the ticket. The sensor is mounted 5.75 mm off the center line of the
mechanism.
In case of Ticket
The default sensor position is (1) as shown on the figure below. To change to the (2)
position, the customer should notify the manufacturer in advance. There can be only one
position for the sensor.
-7-
Ribbon End Sensor
The sensor detects the end portion of the ribbon. The ribbon end must be transparent.
-8-
2. Operations Overview
2.1 Unpacking and Inspection
This printer has been specially packaged to withstand damage during shipping. Please
carefully inspect the packaging and printer upon receiving the bar code printer. Please
retain the packaging materials in case you need to reship the printer.
Unpacking the printer, the following items are included in the carton.









One printer unit
One Windows labeling software/Windows driver CD disk
One quick installation guide
One external auto switching power supply
One power cord
One label spindle
Two fixing tabs
Two ribbon spindles
One paper core for ribbon rewind spindle
If any parts are missing, please contact the Customer Service Department of your
purchased reseller or distributor.
-9-
2.2 Printer Overview
2.2.1 Front View
1
2
5
3
1.
2.
3.
4.
5.
4
P
o
w
e
r
PAUSE button
L
E
PWR.,
ON-LINE and ERR. indicators
D
FEED
button
i
n
Cover
release button
d
Label
dispense opening
i
c
a
t
o
r
- 10 -
2.2.2 Interior View
6
7
8
USB
inter
face
1
9
2
3
4
10
5
11
2.
US
B
Printer cover inte
(in open position)
rfa
PAUSE button
ce
3.
PWR., ON-LINE, ERR. indicators
4.
FEED button
5.
Ribbon supply spindle
6.
Fixing tabs
7.
Label supply roll spindle
8.
Ribbon mechanism
9.
Ribbon rewind spindle
1.
10. Printer carriage release lever
11. Media sensor
12. Adjustable label guide
13. Platen
- 11 -
12
13
2.2.3 Rear View
1
3
2
4
5
US
B
inte
rfa
ce
6
1. Power on/off switch
2. Power supply DC jacket
3. RS-232C interface
4. USB interface
5. Label insert opening (For use with external media)
6. Centronics interface (Factory option)
Note:
The interface picture here is for reference only. Please refer to the product
specification for the interfaces availability.
- 12 -
2.3 LED Indicators and Buttons
2.3.1 LED Indication
LEDs
Indication
PWR. (POWER) Indicator
The green PWR. indicator illuminates when the
POWER switch is turned on.
ON-LINE Indicator
The green ON-LINE indicator illuminates when the
printer is ready to print. When PAUSE button is
pressed, the ON-LINE indicator flashes.
ERR. Indicator
(Error/Paper Empty)
The red ERR. indicator illuminates in the event of a
printer error, such as memory error, syntax error, and
so forth. For a full list of error messages, please refer
to section 6, Troubleshooting Guides.
2.3.2 Buttons
Function
Buttons
PAUSE Button
The PAUSE button allows the user to stop a print job
and then continue the printing with a second
depression of the button. By pressing the PAUSE
button: (1) the printer stops printing after the printing
label, (2) the PAUSE LED flashes, and (3) the printer
will hold all data in memory. This allows for troublefree replacement of label stock and thermal transfer
ribbon. A second depression of the PAUSE button will
restart the printer.
Note: If the PAUSE button is held down for more than 3
seconds, the printer will be reset and all data of
the previous printing job will be lost.
FEED Button
Press the FEED button to feed the label to the top of form
of the next label.
- 13 -
3. Setup
3.1 Setting up the Printer
1. Place the printer on a flat,
secure surface.
2. Make sure the POWER switch
is off.
3. Connect the printer to the
computer mainframe with the
RS-232C or USB cable.
4. Plug the power cord into the
power jacket at the rear of the
printer, and then plug the
power cord into a properly
grounded receptacle.
Note:
Please switch OFF printer power switch prior to plug in the power cord to printer power
jack.
- 14 -
3.2 Loading the Media
1. Open the printer cover.
2. Disengage the printer carriage by pulling
the printer carriage release lever on the
left side of the platen.
3. Slide the label supply roll spindle
through the core of a label roll and
attach the fixing tabs onto the spindle.
4. Place the label roll into the label roll
mount/ or external label roll mount. Feed
the label under the carriage and over the
platen.
External Label Roll Mount (Option)
- 15 -
5. Adjust the label guide to fit the width of
the media.
6. Engage the printer carriage.
7. Wind the label roll until it becomes adequately taut.
8. Close the printer cover and press the FEED button three or four times until the green
ON-LINE indicator illuminates.
9. When the printer is out of ribbon or media, the ON-LINE LED will not illuminate and the
ERR. LED will flash. Reload the ribbon or media without turning off the printer power.
Press the FEED button three or four times until the ON-LINE LED illuminates. The
printing job will be resumed without data loss.
Note:
Please refer to videos on TSC YouTube or software/driver CD disk.
.
- 16 -
3.3 Loading the Ribbon
1. Place an empty paper core on the
ribbon rewind spindle.
2. Insert the left side first. Mount the ribbon
rewind paper core on the front hubs.
3. Please be noted that the bigger hub
1
side with 4 ribs must be installed toward
the right side of ribbon mechanism.
2
4. Install a ribbon on the ribbon supply
spindle. Mount the ribbon supply spindle
on the rear hubs.
- 17 -
5. Please be noted that the bigger hub
side with 4 ribs must be installed toward
the right side of ribbon mechanism.
6. Disengage the printer carriage by
pulling the carriage release lever
upwards.
7. Following the direction of the  RIBBON
label, pull the transparent ribbon leader
to the front from under the ribbon
mechanism.
8. Attach the ribbon leader to the empty
paper core on the ribbon rewind spindle
(with a tape).
- 18 -
9. Rotate the ribbon rewind spindle until
the ribbon overlaps the ribbon leader
and stretches tight.
10. Engage the printer carriage.
11. Close the printer cover and press the
FEED button until the green ON-LINE
LED illuminates.
Note:
1.
Please install ribbon and media and close print head mechanism prior to
turn on power. Printer will determine direct thermal or thermal transfer mode
automatically while turning on printer power.
2.
Please refer to videos on TSC YouTube or software/driver CD disk.
- 19 -
3.4 Install SD Memory Card (Option)
1. Open the memory card cover.
2. Plus the SD memory card module on the main board.
3. Install the SD memory card.
4. Close the memory card cover.
- 20 -
* Recommended SD card specification.
SD card spec
SD card capacity Approved SD card manufacturer
V1.0, V1.1
128 MB
SanDisk, Transcend
V1.0, V1.1
256 MB
SanDisk, Transcend, Panasonic
V1.0, V1.1
512 MB
SanDisk, Transcend, Panasonic
V1.0, V1.1
1 GB
SanDisk, Transcend, Panasonic
V2.0 SDHC CLASS 4 4 GB
V2.0 SDHC CLASS 6 4 GB
SanDisk, Transcend, Panasonic
V1.0, V1.1
microSD 128 MB
Transcend, Panasonic
V1.0, V1.1
microSD 256 MB
Transcend, Panasonic
V1.0, V1.1
microSD 512 MB
Panasonic
V1.0, V1.1
microSD 1 GB
Transcend, Panasonic
V2.0 SDHC CLASS 4 microSD 4 GB
Panasonic
V2.0 SDHC CLASS 6 microSD 4 GB
Transcend
V1.0, V1.1
miniSD 128 MB
Transcend, Panasonic
V1.0, V1.1
miniSD 256 MB
Transcend, Panasonic
V1.0, V1.1
miniSD 512 MB
Transcend, Panasonic
V1.0, V1.1
miniSD 1 GB
Transcend, Panasonic
V2.0 SDHC CLASS 4 miniSD 4 GB
Transcend
V2.0 SDHC CLASS 6 miniSD 4 GB
- The DOS FAT file system is supported for the SD card.
- Folders/files stored in the SD card should be in the 8.3 filename format
- The miniSD/microSD card to SD card slot adapter is required.
- 21 -
4. Using Printer
4.1 Power-on Utilities
There are three power-on utilities to set up and test hardware. These utilities are activated by
pressing the FEED or PAUSE button and turning on the printer power simultaneously. The
utilities are listed as below:
1. Self-test
2. Gap sensor calibration
3. Printer initialization
Note:
Please refer to videos on TSC YouTube or software/driver CD disk.
4.1.1 Self Test and Dump Mode
Install the label first. Press the FEED button and then turn on the printer power. Do not release
the FEED button until the printer feeds labels. The printer performs the following items:
1.
Calibrate label pitch
2.
Print out thermal print head check pattern
3.
Print the internal settings
4.
Enter dump mode
To initiate the self test mode, the printer will calibrate the label length. If the label gap is not
detected within 7", the printer stops feeding labels and the media is treated as continuous paper.
In self test, a check pattern is used to check the performance of the thermal print head. Following
the check pattern, the printer prints internal settings as listed below.
When the self test is completed, the printer enters the dump mode. Please turn the printer's
power off and then on to resume normal printing.
- 22 -
Self-test printout
Model name
F/W version
Firmware checksum
Printer S/N
TSC configuration file
System date
System time
Printed mileage (meter)
Cutting counter
Print speed (inch/sec)
Print darkness
Label size (inch)
Gap distance (inch)
Gap/black mark sensor
intension
Code page
Country code
®
Note: ZPL is emulating for Zebra language.
ZPL setting information
Print darkness
Print speed (inch/sec)
Label size
Control prefix
Format prefix
Delimiter prefix
Printer power up motion
Printer head close motion
RS232 serial port
configuration
Numbers of download files
Total & available memory
space
Print head check pattern
- 23 -
Dump Mode
After the self test, the printer enters the dump mode. In this mode, any characters sent from the
host computer will be printed in two columns, as shown. The characters received will be shown
in the first column, and their corresponding hexadecimal values, in the second. This is often
helpful to users for the verification of programming commands or debugging of printer programs.
Reset the printer by turning the POWER switch off and on.
Hex decimal data
related to left
column of ASCII
data
ASCII Data
4.1.2 Gap Sensor Calibration Utility
This utility is used to calibrate the sensitivity of gap sensor. Users may have to calibrate the gap
sensor for two reasons:
1. The media is being changed to a new type.
2. Initialize the printer.
Note:
The ERR. LED may flash if gap sensor is not calibrated properly.
Please follow the steps below to calibrate gap sensor:
1. Turn off the printer power and install blank labels (without any logo or character) on printer.
- 24 -
2. Hold down the PAUSE button then turn on printer power.
Release PAUSE button when the printer feeds labels. Do not turn off printer power until the
printer stops and two green LEDs light on.
Note:
Black mark sensor has fixed sensitivity. It is no need to calibrate the black mark sensor
4.1.3 Printer Initialization
Printer initialization sets printer parameters to default values. And it will not clear downloaded files
resident in flash memory.
Please follow the steps below to initialize the printer:
1. Turn off the printer power.
2. Hold down the PAUSE and FEED buttons and turn on the printer power.
3. Do not release the buttons until the three LEDs flash in turn.
Note:
1. Printing method (thermal transfer or thermal direct printing) will be set automatically at
the activation of printer power.
2. When printer initialization is done, sensor sensitivity is reset to default. Sensor
calibration is required before printing labels.
3. Download files will not be deleted after printer initialization. For more information about
deleting files, please refer to TSPL2 programming manual KILL command section or
using DiagTool.
Printer configuration will be restored to defaults as below after initialization.
Parameter
Speed
Density
Media Width
Media Height
Sensor Type
Gap Setting
Print Direction
Reference Point
Offset
Post-Print Action
Default setting
76.2 mm/sec (3 ips)
8
4” (101.6 mm)
4” (101.6 mm)
Gap sensor
0.12” (3.0 mm)
0
0,0 (upper left corner)
0
Tear mode
- 25 -
Serial Port Settings
Code Page
Country Code
Clear Flash Memory
9600 bps, none parity, 8 data bits, 1 stop bit
850
001
No
- 26 -
5. Diagnostic Tool
TSC’s Diagnostic Utility is an integrated tool incorporating features that enable you to explore a
printer’s settings/status; change a printer’s settings; download graphics, fonts and firmware;
create a printer bitmap font; and send additional commands to a printer. With the aid of this
powerful tool, you can review printer status and setting in an instant, which makes it much easier
to troubleshoot problems and other issues.
5.1 Start the Diagnostic Tool
1. Double click on the Diagnostic tool icon
to start the software.
2. There are four features (Printer Configuration, File Manager, Bitmap Font Manager, Command
Tool) included in the Diagnostic utility.
Features tab
Interface
Printer
functions
Printer setup
Printer Status
- 27 -
5.2 Printer Function
1. Connect the printer and computer with a cable.
2. Select the PC interface connected with bar code printer.
USB cable
RS-232 cable
2
1
The default interface setting is USB
interface. If USB interface is
connected with printer, no other
settings need to be changed in the
interface field.
3. Click the “Printer Function” button to setup.
4. The detail functions in the Printer Function Group are listed as below.
Function
Reset Printer
Description
Calibrate the sensor specified in the Printer
Setup group media sensor field
Setup the IP address, subnet mask, gateway for
the on board Ethernet
Synchronize printer Real Time Clock with PC
Initialize the printer and restore the settings to
factory default.
Reboot printer
Print Test Page
Print a test page
Configuration Page
Print printer configuration
Dump Text
To activate the printer dump mode.
Ignore AUTO.BAS
Ignore the downloaded AUTO.BAS program
Exit Line Mode
Exit line mode.
Password Setup
Set the password to protect the settings
Calibrate Sensor
Ethernet Setup
RTC Setup
Factory Default
For more information about Diagnostic Tool, please refer to the diagnostic utility quick start
guide in the software/driver CD disk \ Utilities directory.
- 28 -
6. Troubleshooting
The following guide lists the most common problems that may be encountered when operating this
bar code printer. If the printer still does not function after all suggested solutions have been
invoked, please contact the Customer Service Department of your purchased reseller or distributor
for assistance.
Problem
Ribbon does not advance
or rewind
Poor print quality
Power indicator on printer
does not illuminate
ON-LINE indicator is off,
ERR. indicator is on
Solution
1. The media and ribbon must be installed then engage the
print head mechanism prior to turning on printer power.
2. Install the black ribbon spindle at the correct direction.
3. Please check the "Media settings method" in the driver if it
is set to direct thermal mode.
1. Clean the thermal print head.
2. Adjust the print density setting.
3. Ribbon and media are not compatible.
4. Media thickness is over spec.
5. Check if correct power supply is connected with printer.
1. Check the power cord see whether it is properly
connected.
2. Check if the LED on the power supply is illuminated. If it is
not lit on, then the power supply is damaged.
3. Check if correct power supply is connected with printer.
1. Out of paper or out of ribbon
If there is one beep sound when printer is error, then
it's gap sensor problem. Please check the following
items.
 Calibrate gap sensor or setup the paper length in
labeling software/program properly.
 Install the paper at the correct
If there are two beeps sound when printer is error then
it's ribbon sensor problem. Please check the following
items.
 Is outside wound ribbon is used with this printer?
 Is ribbon threaded correctly in the mechanism?
 Is paper core installed on the ribbon take up spindle?
Continuous feeding when
printing labels
2. Calibrate the sensitivity of gap sensor.
1. Check the driver or command script setting if sensor type
is set properly.
2. Calibrate the gap sensor again if die cut media is used for
printing.
- 29 -
7. Maintenance
This session presents the clean tools and methods to maintain your printer.
1. Please use one of following material to clean the printer.
 Cotton swab
 Lint-free cloth
 Vacuum / Blower brush
 100% Ethanol or Isopropyl Alcohol
2. The cleaning process is described as following,
Printer Part
Method
Interval
1. Always turn off the printer before
cleaning the print head.
2. Allow the print head to cool for a
Clean the print head when changing
minimum of one minute.
a new label roll.
3. Use a cotton swab and 100% Ethanol
or Isopropyl Alcohol to clean the print
head surface.
Print Head
Platen Roller
Sensor
Exterior
Interior
1. Turn the power off.
2. Rotate the platen roller and wipe it
thoroughly with water.
Clean the platen roller when
changing a new label roll
Compressed air or vacuum
Wipe it with water-dampened cloth
Brush or vacuum
Monthly
As needed
As needed
Note:

Do not touch printer head by hand. If you touch it careless, please use ethanol to clean it.

Please use 100% Ethenol or Isopropyl Alcohol. DO NOT use medical alcohol, which may damage
the printer head.

Regularly clean the print head and supply sensors once change a new media to keep printer
performance and extend printer life.
- 30 -
Revise History
Date
Content
- 31 -
Editor
TSC Auto ID Technology Co., Ltd.
Corporate Headquarters
9F., No.95, Minquan Rd., Xindian Dist.,
New Taipei City 23141, Taiwan (R.O.C.)
TEL: +886-2-2218-6789
FAX: +886-2-2218-5678
Web site: www.tscprinters.com
E-mail: [email protected]
[email protected]
Li Ze Plant
No.35, Sec. 2, Ligong 1st Rd., Wujie Township,
Yilan County 26841, Taiwan (R.O.C.)
TEL: +886-3-990-6677
FAX: +886-3-990-5577
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement