Duplex CPU units

Duplex CPU units
Programmable
Controllers
[email protected]@
Duplex CPU units
The CS1 Duplex System Boosts the Reliability of Facilities and Equipment
Hot Standby System for CPU Unit Duplexing
• When a problem occurs in the CPU Unit, the system instantly
switches control to the other CPU Unit, enabling continuous
operation with minimal effect on the system.
• Because there is no need for special duplex programming,
the design process is simple and design steps are reduced.
Note: The system can also be configured with only one each of the
CPU, Power Supply, and Communications Units. This lets you
optimize the system cost by selecting the Units that you need.
(The Duplex Unit must be used even when using only one each
of the CPU, Power Supply, and Communications Units.)
Higher Network Reliability
Duplex Communications Units and a loopback configuration enable
continuous communications even in the event of a problem.
Broken
line
Communications
line backup
by a loopback
configuration
Node backup
by Duplex
Communications
Unit
Unit down
Note: The CS1W-CLK12-V1 or CS1W-CLK52-V1 is required for network duplexing.
Duplex CPU Units for greater system reliability
Duplex Communications (Controller Link) Units
for greater network reliability
Duplex CPU units
Duplex Unit
Duplex Power Supply Units protect
against power supply problems
267
With the Duplex PLC System, restoring the system is fast and easy.
The CPU, Power Supply, or Communications Unit can be
replaced while the system continues to operate.
Operating
If the CPU Unit should stop due to malfunction, operation continues
with the other CPU Unit so you can replace the broken Unit without
even stopping the system. The same is possible for the Power Supply
and Communications Units.
Operating
On
standby
Naturally, Basic and Special I/O Units can also be replaced.
Units can be replaced,
and problems solved,
without stopping the
system.
With the CS1D, Basic I/O Units, Special I/O Units, and CPU Bus Units
can all be replaced during operation. The Unit being replaced stops
operating during replacement, but all other Units continue to operate.
Starts
operating
On
standby
lem
Probcurs
oc
Duplex
operation
resumes.
A high-performance PLC with advanced functions to expand control possibilities.
High reliability, plus high performance.
The CPU Units in this Duplex System feature both high performance
and advanced functions, providing high reliability even to applications
requiring high speed.
Approx. 50%
(compared
with previous
OMRON
duplex
models)
Of course, PLC functions have also been increased.
• Built-in Flash memory enables battery-less operation.
• Various self-diagnostic functions are included.
• A wide range of calculation functions includes floating point
calculations, character string processing, and PID calculations with auto tuning.
• Structured programming (multitask and variable programming supported)
Installation costs and maintenance costs are reduced.
Allows effective use of software assets.
The same support software can be used in systems combining the CS1
and CJ1 Series, and all software programs and data are compatible.
There is no need for ladder programs for duplexing. This means that
when converting an existing system to a Duplex System, there is
almost no need to revise ladder programs.
Complete compatibility among Units.
The CS1D Duplex System is fully compatible with the I/O Units of the
entire CS Series. The same Units and materials can be used for hardware replacement and system maintenance. There is no need to
purchase different Units and materials for each system, making the
CS1D Duplex System highly economical.
(The CS1D only supports the CS1 Series I/O Units, not the C200H
series I/O units)
268
Programmable Controllers
Programmable
Controllers
Dimensions
Unit: mm
Backplane
CPU Backplanes
Unit: mm
Backplane
CS1W-BC023 (2 slots)
CS1W-BC033 (3 slots)
CS1W-BC053 (5 slots)
CS1W-BC083 (8 slots)
CS1W-BC103 (10 slots)
CS1D-BC052 (Duplex System)
A
172.3
246
316
421
491
B
145
118
W
198.5
260
330
435
505
H
157
130
D
123
Backplanes
CPU Backplane with 2 Slots
Four, M4
Model
CS1W-BC023 (2 slots)
CS1W-BC033 (3 slots)
CS1W-BC053 (5 slots)
CS1W-BC083 (8 slots)
CS1W-BC103 (10 slots)
CS1D-BC052
(Duplex System)
CS1 Expansion
CS1W-BI033 (3 slots)
Backplanes
CS1W-BI053 (5 slots)
CS1W-BI083 (8 slots)
CS1W-BI103 (10 slots)
CS1D-BI092
(Duplex System)
C200H Expansion I/O C200HW-BI031 (3 slots)
Backplanes
C200HW-BI051 (5 slots)
C200HW-BI081-V1
(8 slots)
C200HW-BI101-V1
(10 slots)
A
172.3
246
316
421
491
W
198.5
260
330
435
505
246
316
421
491
260
330
435
505
175
245
350
189
259
364
420
434
Mounting Depth
CS1W-BC023
CPU Backplane
145±0.3
The depth of all Racks is from 118 to 153 mm depending on the Units
that are mounted. Additional depth is required to connect Peripheral
Devices and Cables. Be sure to allow sufficient mounting depth.
172.3±0.3
Note: Expansion Backplanes cannot be connected to 2-slot CPU Backplanes.
CPU Backplane with 3, 5, 8, or 10 Slots
Four, M4
A±0.3
118 to 153 mm
130
CPU Backplane
180 to 223 mm
118±0.3
Note: I/O Connecting Cables require sufficient space to maintain the
min. bending radius.
68 min.
130
Four, M4
A±0.3
Expansion Backplane
80
CS1 I/O Connecting Cable
(Cable diameter: 8.6 mm)
118±0.3
R ≥ 69 mm
R ≥ 41 mm
W
CS1 to C200H I/O Connecting Cable
(Cable diameter: 5.1 mm)
R ≥ 41 mm
Duplex CPU units
C200H I/O Connecting Cable
(Cable diameter: 5.1 mm)
Long-distance Connecting Cable
(Cable diameter: 10 mm)
R ≥ 80 mm
269
Connections to Programming Devices
Serial Communications Units
Serial Communications Board
Peripheral port
RS-232C port
Connecting Cable
XW2Z-200S-CV (See note.)
XW2Z-500S-CV (See note.)
Hardware
Software
IBM PC/AT or compatible
CX-Programmer
CX-Simulator
Note: 1. Refer to the next page for details of cables for connecting to computers. Choose the appropriate
cable for the communications mode.
2. The following cables can be used for a Host Link connection (but not a peripheral bus
connection):
270
Programmable Controllers
NEW
USB-Serial
Conversion Cable
CS1W-CIF31
CS1W-CN226
CS1W-CN626
CS1W-CN118
[email protected]@(@)
RS-232C Cable
NEW
USB-Serial
Conversion Cable
CS1W-CIF31
Programmable
Controllers
Hardware
Connecting Cable
Software
IBM PC/AT or compatible
IBM PC/AT or compatible
CX-Programmer
CX-Simulator
(See previous page.)
CS1W-CN114
CQM1-CIF02
Connecting
Cable
NEW
USB-Serial
Conversion Cable
CS1W-CIF31
IBM PC/AT or compatible
RS-232C connector (25 pins)
Duplex CPU units
CS1W-CN224
CS1W-CN624
C200H-PRO27-E
CS1W-KS001-E
CS1W-CN114
CQM1-PRO01-E
CS1W-KS001-E
271
Programming Consoles
Connecting to the Peripheral Port
CQM1H-PRO01-E
Peripheral port
RS-232C,
9-pin (D-sub)
Cable provided with
CQM1H-PRO01-E (2 m)
Peripheral port
Connecting Cable
Peripheral Port Connecting Cables
CS1W-KS001-E
Key Sheet
CQM1-PRO01-E
Programming
Model
CQM1H-PRO01-E
Cable
Not required.
Cable length
---
CQM1-PRO01-E (See note.)
Cable provided with
CQM1-PRO01-E
CS1W-KS001-E
Key Sheet
CQM1-PRO01-E
Programming Console
Cable
Length
CS1W-CN226
CS1W-CN626
2.0 m
6.0 m
The following cables can be used for an RS-232C connection from the
computer to the peripheral port.
Mode
Connecting cables
Peripheral
bus or
Host Link
Host Link
XW2Z-200S-CV or
XW2Z-500S-CV
Cable
CS1W-CN114
Cable length
0.05 m
2 or 5 m +
0.1 m
Computer
connector
D-sub,
9-pin, male
XW2Z-200S-V or
XW2Z-500S-V
RS-232C ports on Serial
Communications Board
RS-232C cable
XW2Z-200S-CV (2 m)
XW2Z-500S-CV (5 m)
RS-232C port on CPU Unit
RS-232C Port Connecting Cables
Mode
Cable
Peripheral XW2Z-200S-CV
bus or
XW2Z-500S-CV
Host Link
Length
2.0 m
5.0 m
Computer connector
D-sub, 9-pin, male
Note: Cables with model numbers ending in “CV” are antistatic.
The following cables can be used for an RS-232C connection from the
computer to an RS-232C port. (Unlike cables with model numbers
ending in “-CV,” however, these cables do not support peripheral bus
connection and do not have anti-static specifications.)
C200H-PRO27-E
Mode
Host Link
CS1W-KS001-E
Key Sheet
C200H-PRO27-E
Programming Console
Model
C200H-PR027-E
CS1WCN118
RS-232C,
9-pin (D-sub)
CS1W-CN114
Model
CQM1-PRO01-E
Length
Connecting to the RS-232C Port
Peripheral port
Note: The above configuration is also possible for the
C200H-PRO27-E with a Programming Console
Cable, such as the C200H-CN222.
Computer
connector
D-sub, 9-pin,
male
Cable
CS1W-CN224
CS1W-CN624
CS1W-CN224: 2.0 m
CS1W-CN624: 6.0 m
Peripheral port
Cable length
2.0 m
6.0 m
Cable
XW2Z-200S-V
XW2Z-500S-V
Length
2.0 m
5.0 m
Computer connector
D-sub, 9-pin, male
The following serial communications modes can be used to connect a
computer with the CX-Programmer to a CS1 PLC.
Mode
Features
Peripheral bus The faster mode, peripheral bus is generally used for
CX-Programmer connections.
Only 1:1 connections are possible. The baud rate is
automatically detected with the CS1.
Host Link
A standard protocol for host computers.
Slower than peripheral bus, but allows modem or optical adapter connections, or long-distance or 1:N connections
via RS422A/485.
Windows-based Programming Software: CX-Programmer
Name
CX-Programmer
272
Model
[email protected]@
For 1 license
[email protected]@ For 3 licenses
[email protected]@ For 10 licenses
Specifications
OS: Windows
95/98 or
Windows NT/Me/
2000/XP
Programmable Controllers
CS1W-CIF31
USB-Serial Conversion Cable
Serial Connecting Cable:
IBM PC/AT or compatible CS1W-CN226/CN626
XW2Z-200S-CV/500S-CV
with USB port
XW2Z-200S-V/500S-V
CQM1-CIF02
Peripheral or RS-232C port
CX-Programmer, CX-Simulator, CX-Protocol, CX-Motion, CX-Positioner, CS-Process, DeviceNet Configurator, PLC Reporter 32, NS-Designer, and NT Support Software for Windows (NTST) (See note.)
Note: There are restrictions to the COM port numbers that can be used
for the NTST.
Applicable Communications Middleware
FinsGateway and CX-Server
General Specifications of USB-Serial Conversion Cable
USB interface standard
DTE speed
Connectors
On computer
On PLC
Power supply
Current consumption
Operating envi- Ambient
ronment
temperature
Ambient
humidity
Ambient
atmosphere
Weight
Conforms to USB Specification 1.1.
115.2 Kbits/s
USB (A plug connector, male)
RS-232C (D-sub, 9-pin, female)
Bus power (supplied from upstream, 5 V
DC)
35 mA
0 to 55 °C
10% to 90% (with no condensation)
Applicable PLCs and PTs
The OMRON PLCs and PTs supported by the applicable software can
be used. These are listed below.
PLCs
CS Series, CJ Series, C Series (C200HS, C200HX/HG/HE, C200H,
C1000H, C2000H, CQM1, CPM1, CPM1A, SRMT, CQM1H, and
CPM2C), CVM1, and CV Series
PTs
NS Series and NT Series
No corrosive gases
50 g
OS with Drivers for USB-Serial Conversion Cable
Windows 98, ME, 2000, or XP
Peripheral Port Connecting Cables
Computer
IBM PC/AT or
compatible
Serial Communications
Node
Tool bus or SYSMAC WAY
Connecting Cable model number
Length
Computer connector
CS1W-CIF31
0.5 m + 2.0 m
0.5 m + 6.0 m
0.5 m +
(2.0 m or 5.0 m)
+ 0.1 m
0.5 m +
(2.0 m or 5.0 m)
+ 0.1 m
USB (A plug connector)
CS1W-CIF31
SYSMAC WAY
CS1W-CIF31
CS1W-CN226
CS1W-CN626
XW2Z-200S-CV/
XW2Z-500S-CV
CS1W-CN118
XW2Z-200S-V/
XW2Z-500S-V
RS-232C Port Connecting Cables
Computer
Serial Communications Connecting Cable model number
Node
IBM PC/AT or compatible Tool bus or SYSMAC WAY CS1W-CIF31
XW2Z-200S-CV
XW2Z-500S-CV
SYSMAC WAY
CS1W-CIF31
XW2Z-200S-V
(See note.)
XW2Z-500S-V
(See note.)
Length
Computer connector
0.5 m + 2.0 m
0.5 m + 5.0 m
0.5 m + 2.0 m
USB (A plug connector)
0.5 m + 5.0 m
Connection in Tool Bus Mode is not possible. The connector does not have ESD measures.
Duplex CPU units
273
Programmable
Controllers
Using a USB-Serial Conversion Cable to Connect to a Peripheral or RS-232C Port
Applicable Software
I/O Allocations
I/O Allocations
In CS1 PLCs, part of the I/O memory is allocated to each Unit. Units are divided into the following 3 groups for allocations.
• Basic I/O Units
• Special I/O Units
• CS1 CPU Bus Units
Basic I/O Units
Allocations
CIO Area:
CIO 0000 to CIO 0319 (See Note 1.)
(Memory is allocated in word units in order of mounting position in the Racks.)
Note
C200H Basic I/O Units
CS1 Basic I/O Units
1.
The Rack's first word setting can be changed from the default setting
(CIO 0000) to any word from CIO 0000 to CIO 9999. The first word
setting can be changed only with a Programming Device other than a
Programming Console.
2.
The unit number setting on the front of C200H Group-2 High-density
I/O Units is ignored. Words are allocated to these Units based on their
location in the Rack.
C200H Group-2 High-density I/O Units
(See Note 2.)
Special I/O Units
Allocations
Special I/O Unit Area:
CIO 2000 to CIO 2959
(Each Unit is allocated ten words based on its unit number.)
Note 1.
2.
CS1 Special I/O Units
Although there are 96 unit number settings, a maximum of 80 Units
can actually be mounted to a PLC because that is the maximum
number of slots possible.
Some Units classified as I/O Units (namely C200H High-density I/O
Units) are actually treated as Special I/O Units.
C200H Special I/O Units
(See Note 2.)
CS1 CPU Bus Units
Allocations
CS1 CPU Bus Unit Area:
CIO 1500 to CIO 1899
(Each Unit is allocated 25 words based on its unit number.)
CS1 CPU Bus Units
274
Power Supply Unit
1. CPU Rack
Basic I/O Units on the CPU Rack are allocated words left to right; Units
are allocated as many words as required in word units.
CIO
0000
Power Supply Unit
Allocation Methods
Slot numbers 2, 3, 5, 8, and 10
CPU Unit
Basic I/O Units include CS1 Basic I/O Units, C200H Basic I/O Units,
and C200H Group-2 High-density I/O Units.
Allocated words in the CIO Area: CIO 0000 to CIO 0319
Basic I/O Units can be mounted to the CPU Rack, CS1 Expansion
Racks, and C200HX/HG/HE Expansion I/O Racks.
Note: CS1 Basic I/O Units cannot be mounted to C200HX/HG/HE
Expansion I/O Racks.
CPU Unit
Allocations to Basic I/O Unit Groups
CPU Rack
Example
IN
OUT
IN
IN
OUT
64
32
8
16
8
CIO
CIO
CIO CIO 0002 CIO 0007
0000 0001
0006
to
to
0005
0008
CPU Rack
Programmable Controllers
Series Series B
A
CS1 Expansion
Rack
CS1 Expansion
Rack
CS1
Expansion
Rack
I/O Interface
Unit
CS1 Expansion
Rack
Terminating I/O Interface
resistance Unit
CS1 Expansion
Rack
Power Supply Unit
I/O Interface
Unit
Terminating
resistance
Duplex CPU units
CS1 Expansion
Rack
I/O Interface
Unit
275
Programmable
Controllers
Power Supply Unit
CPU Unit
I/O Control
Unit
Power Supply Unit
Power Supply Unit
Words allocated
in order from
Rack nearest
CPU Rack.
CPU Rack
Power Supply Unit
Power Supply Unit
CPU Rack
3. CS1 Long-distance Expansion Racks
Words are allocated to series A and then series B. Otherwise, allocations are the same as for other Racks.
Power Supply Unit
CPU Unit
CIO
0000
Power Supply Unit
2. Allocations to CS1 Expansion and C200H Expansion I/O Racks
I/O allocations to Basic I/O Units continue from the CPU Rack to the
Expansion Racks. Words are allocated from left to right and each Unit
is allocated as many words as it requires in word units, just like Units in
the CPU Rack.
Allocations to Special I/O Units
Allocations to CS1 CPU Bus Units
Special I/O Units include CS1 Special I/O Units and C200H Special I/O
Units.
Each of these Units is allocated ten words in the Special I/O Unit Area
(CIO 2000 to CIO 2959).
Special /O Units can be mounted to the CPU Rack, CS1 Expansion
Racks, and C200H Expansion I/O Racks. (See note.)
Note: CS1 Special I/O Units cannot be mounted to C200H Expansion
I/O Racks.
Each Unit is allocated 10 words in the Special I/O Unit Area, as shown
in the following table.
Each CS1 CPU Bus Unit is allocated 25 words in the CS1 CPU Bus Unit
Area (CIO 1500 to CIO 1899).
CS1 CPU Bus Units can be mounted to the CPU Rack or CS1 Expansion Racks.
Each Unit is allocated 25 words in the CPU Bus Unit Area, as shown in
the following table.
Unit number
0
1
2
...
15
...
95
Words allocated
CIO 2000 to CIO 2009
CIO 2010 to CIO 2019
CIO 2020 to CIO 2029
...
CIO 2150 to CIO 2159
...
CIO 2950 to CIO 2959
Unit number
0
1
2
...
15
Words allocated
CIO 1500 to CIO 1524
CIO 1525 to CIO 1549
CIO 1550 to CIO 1574
...
CIO 1875 to CIO 1899
Note: CS1 CPU Bus Units are ignored during I/O allocation to Basic I/
O Units. Slots containing CS1 CPU Bus Units are treated as
empty slots.
Note: Special I/O Units are ignored during I/O allocation to Basic I/O
Units. Slots containing Special I/O Units are treated as empty
slots.
Current Consumption
The amount of current/power that can be supplied to the Units mounted in a Rack is limited by the capacity of the Rack’s Power Supply Unit. The
system must be designed so that the total current consumption of the Units does not exceed the maximum current for each voltage group and the
total power consumption does not exceed the maximum for the Power Supply Unit.
CPU Racks and Expansion Racks
The following table shows the maximum currents and power that can be supplied by Power Supply Units on CPU Racks and Expansion Racks
(both CS1 Expansion Racks and C200H Expansion I/O Racks).
Note: 1. When calculating current/power consumption in a CPU Rack, be sure to include the power required by the CPU Backplane and CPU Unit
themselves.
2. Likewise, be sure to include the power required by the Expansion Backplane itself when calculating current/power consumption in an
Expansion Rack.
Power Supply Unit
Max. Current Consumption
5-V group
4.6 A
4.6 A
4.6 A
4.6 A
9A
C200HW-PA204
C200HW-PA204S
C200HW-PA204R
C200HW-PD204
C200HW-PA209R
26-V group
0.6 A
0.6 A
0.6 A
0.6 A
1.3 A
Max. Total Power Consumption
24-V group
None
0.8 A
None
None
None
30 W
30 W
30 W
30 W
45 W
Be sure both Condition 1 and Condition 2 are met.
Condition 1: Maximum Current Supply
1. Current required at 5 V DC by all Units (A) ≤ Max. Current shown in table
2. Current required at 26 V DC by all Units (B) ≤ Max. Current shown in table
3. Current required at 24 V DC by all Units (C) ≤ Max. Current shown in table
Condition 2: Maximum Total Current Supply
1. A × 5 V DC + B × 26 V DC + C × 24 V DC ≤ Max. Power shown in table
Example Calculations
In this example, the following Units are mounted to a CPU Rack with a C200HW-PA204S Power Supply Unit.
Unit
CPU Backplane
(8 slots)
CPU Unit
Input Units
Model
CS1W-BC083
CS1H-CPU67-EV1
C200H-ID216
CS1W-ID291
Output Units
C200H-OC221
Special I/O Unit
C200H-NC213
CPU Bus Unit
CS1W-CLK21
Service Power Supply Unit (24 V DC)
Total current/power consumption
13.15+3.9+7.2 = 24.25 (≤30 W)
276
Quantity
1
5- V DC
0.11 A
26- V DC
---
24- V DC
---
1
2
2
2
1
1
0.3 A used
1.10 A
0.10 A
0.20 A
0.01 A
0.30 A
0.50 A
--2.63 A (≤4.6) x 5 V = 13.15W
------0.075 A
------0.15 A ¢≤0.6A) x 26 V = 3.9 W
------------0.3 A
0.3 A ¢≤0.8A) x 24 V = 7.2 W
Programmable Controllers
Category
Name
C200H Output Relay Output
Units
Units
5- V DC Voltage Group
Name
CPU Units
(These values include current
consumption by a Programming
Console.)
Model
CS1H-CPU67H
CS1H-CPU66H
CS1H-CPU65H
CS1H-CPU64H
CS1H-CPU63H
CS1G-CPU45H
CS1G-CPU44H
CS1G-CPU43H
CS1G-CPU42H
Loop Control Boards
CS1W-LCB01
CS1W-LCB05
Serial Communication Boards
CS1W-SCB21
CS1W-SCB41
CPU Backplanes (for CS1 Units CS1W-BC022
only)
CS1W-BC032
CS1W-BC052
CS1W-BC082
CS1W-BC102
CPU Backplanes
CS1W-BC023
CS1W-BC033
CS1W-BC053
CS1W-BC083
CS1W-BC103
I/O Control Unit
CS1W-IC102
CS1 Expansion Backplanes (for CS1W-BI032
CS1 Units only)
CS1W-BI052
CS1W-BI082
CS1W-BI102
CS1 Expansion Backplanes
CS1W-BI033
CS1W-BI053
CS1W-BI083
CS1W-BI103
I/O Interface Unit
CS1W-II102
C200H Expansion I/O Backplanes C200HW-BI031
C200HW-BI051
C200HW-BI081-V1
C200HW-BI101-V1
Consumption (A)
0.82 (See note.)
0.82 (See note.)
0.82 (See note.)
0.82 (See note.)
0.82 (See note.)
0.78 (See note.)
0.78 (See note.)
0.78 (See note.)
0.78 (See note.)
0.22 (See note.)
0.22 (See note.)
0.28 (See note.)
0.36 (See note.)
0.11
0.11
0.11
0.11
0.11
0.11
0.11
0.11
0.11
0.11
0.92
0.23
0.23
0.23
0.23
0.23
0.23
0.23
0.23
0.23
0.15
0.15
0.15
0.15
Transistor Output Units
B7A Interface
Units
Triac Output
Units
CS1 Output
Units
Transistor Output Units
Triac Output
Units
CS1W-OA211
C200H Group- Transistor Out2 High-density put Units
Output Units
CS1 I/O Units
Note: Add 0.15 A per port when the NT-AL001-E is connected.
Basic I/O Units
Category
C200H Input
Units
Name
DC Input Units
AC Input Units
C200H Input
Units
AC/DC Input
Units
B7A Interface
Units
Interrupt Input
Unit
C200H Group- DC Input Units
2 High-density
Input Units
CS1 Input
Units
DC Input Units
AC Input Units
Model
C200H-ID211
C200H-ID212
C200H-IA121
C200H-IA122
C200H-IA122V
C200H-IA221
C200H-IA222
C200H-IA222V
C200H-IM211
C200H-IM212
C200H-B7AI1
C200H-B7A12
C200HS-INT01
Consumption (A)
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.10
0.10
0.02
C200H-ID216
C200H-ID217
C200H-ID218
C200H-ID219
C200H-ID111
CS1W-ID211
CS1W-ID231
CS1W-ID261
CS1W-ID291
CS1W-IA111
CS1W-IA211
CS1W-INT01
0.10
0.12
0.10
0.12
0.12
0.10
0.15
0.15
0.20
0.11
0.11
0.10
Interrupt Input
Unit
High-speed Input CS1W-IDP01
Unit
Safety Relay Unit CS1W-SF200
Duplex CPU units
Relay Output
Units
Model
C200H-OC221
C200H-OC222
C200H-OC222N
C200H-OC225
C200H-OC226N
C200H-OC223
C200H-OC224
C200H-OC224N
C200H-OD411
C200H-OD213
C200H-OD214
C200H-OD216
C200H-OD211
C200H-OD217
C200H-OD212
C200H-OD21A
C200H-B7A01
C200H-B7A02
C200H-OA223
C200H-OA222V
C200H-OA224
CS1W-OC201
CS1W-OC211
CS1W-OD211
CS1W-OD212
CS1W-OD231
CS1W-OD232
CS1W-OD261
CS1W-OD262
CS1W-OD291
CS1W-OD292
CS1W-OA201
C200H I/O
Units
DC Input/Transistor Output
Units
TTL I/O Unit
B7A Interface
Units
Analog Timer
Unit
C200H-OD218
C200H-OD21B
C200H-OD219
CS1W-MD261
CS1W-MD262
CS1W-MD291
CS1W-MD292
CS1W-MD561
C200H-B7A21
C200H-B7A22
C200H-TM001
Consumption (A)
0.01
0.01
0.008
0.05
0.03
0.01
0.01
0.01
0.14
0.14
0.14
0.01
0.16
0.01
0.18
0.16
0.10
0.10
0.18
0.20
0.27
0.10
0.13
0.17
0.17
0.27
0.27
0.39
0.39
0.18
0.18
0.23 max.
(0.07+0.02×
No. of points ON)
0.406 max.
(0.07+0.021×No. of
points ON)
0.27
0.48
0.48
0.27
0.27
0.35
0.35
0.27
0.10
0.10
0.06
0.10
0.10
277
Programmable
Controllers
Current Consumption Tables
Special I/O Units
Category
Consumption
(A)
C200H HighDC Input Unit
C200H-ID215
0.13
density I/O
TTL Input Unit
C200H-ID501
0.13
Units (Special I/ Transistor Output Unit
C200H-OD215
0.22
O Units)
TTL Output Unit
C200H-OD501
0.22
TTL I/O Unit
C200H-MD501
0.18
DC Input Transistor Out- C200H-MD215
0.18
put Unit
C200H-MD115
0.18
C200H Special Temperature Control
C200H-TC001
0.33
I/O Units
Units
C200H-TC002
0.33
C200H-TC003
0.33
C200H-TC101
0.33
C200H-TC102
0.33
C200H-TC103
0.33
Heat/Cool Temperature C200H-TV001
0.33
Control Units
C200H-TV002
0.33
C200H-TV003
0.33
C200H-TV101
0.33
C200H-TV102
0.33
C200H-TV103
0.33
Temperature Sensor
C200H-TS001
0.45
Units
C200H-TS002
0.45
C200H-TS101
0.45
C200H-TS102
0.45
C200H Special PID Control Units
C200H-PID01
0.33
I/O Units
C200H-PID02
0.33
C200H-PID03
0.33
Cam Positioner Unit
C200H-CP114
0.30
ASCII Units
C200H-ASC02
0.20
C200H-ASC11
0.25
C200H-ASC21
0.30
C200H-ASC31
0.30
Analog Input Units
C200H-AD001
0.55
C200H-AD002
0.45
C200H-AD003
0.10
Analog Output Units
C200H-DA001
0.65
C200H-DA002
0.60
C200H-DA003
0.10
C200H-DA004
0.10
Analog I/O Units
C200H-MAD01
0.10
High-speed Counter
C200H-CT001-V1 0.30
Units
C200H-CT002
0.30
C200H-CT021
0.45
Motion Control Unit
C200H-MC221
0.65
(w/Teaching
Box: 0.85)
C200HW-MC402- 0.60
E
Position Control Units
C200HW- NC113 0.30
C200HW-NC213 0.30
C200HW-NC413 0.50
ID Sensor Units
C200H-IDS01-V1 0.25
C200H-IDS21
0.25
Fuzzy Logic Unit
C200H-FZ001
0.30
Voice Unit
C200H-OV001
0.30
DeviceNet Master Unit C200HW0.25
DRM21-V1
DeviceNet I/O Link Unit C200HW-DRT21 0.25
CANopen Unit
C200HW0.25
CORT21-V1
PROFIBUS-DP
C200HW-PRM21 0.60
Master Unit
PROFIBUS-DP
C200HW-PRT21 0.25
I/O Link Unit
CompoBus/S Master
C200HW0.15
Unit
SRM21-V1
PC Link Unit
C200H-LK401
0.35
278
Name
Model
Category
Name
Model
CS1 Special Analog Input Unit
I/O Unit
Analog Output Unit
Analog I/O Unit
Isolated Thermocouple
Input Unit
[email protected]@@
[email protected]@@
CS1W-MAD44
CS1W-PTS01
CS1W-PTS11
CS1W-PTS02
CS1W-PTS12
Isolated Temperatureresistance Thermometer Input Unit
Isolated Temperature- CS1W-PTS03
resistance Thermometer Input Unit (Ni508.4
Ω)
Isolated Two-wire
CS1W-PTW01
Transmission Device Input Unit
Isolated DC Input Unit CS1W-PDC01
CS1W-PDC11
Isolated Pulse Input Unit CS1W-PPS01
Isolated Control Output CS1W-PMV01
Unit
Power Transducer Input CS1W-PTR01
Unit
100-mV DC Input Unit CS1W-PTR02
Motion Control Units
CS1W-MC221
Position Control Units
High-speed Counter
Units
SSI Input Unit
Customizable Counter
Units
GP-IB Interface Unit
RFID Sensor Unit
Consumption
(A)
0.13
0.13
0.20
0.15
0.12
0.15
0.12
0.15
0.15
0.15
0.12
0.20
0.15
0.15
0.60
(w/Teaching Box:
0.80 A)
CS1W-MC421
0.70
(w/Teaching Box:
1.00 A)
CS1W-MCH71
0.8
CS1W-NC113/ 133 0.25
CS1W-NC213/ 233
CS1W-NC413/ 433 0.36
CS1W-CT021
CS1W-CT041
0.45
CS1W-CTS21
0.32
CS1W-CTS21
CS1W-HCP22-V1 0.80
CS1W-HCA12-V1 0.75
CS1W-HCA22-V1
CS1W-HIO01-V1 0.60
CS1W-GPI01
0.26
CS1W-V600C11
0.26
CS1W-V600C12
0.32
CS1 CPU Bus Units
Category
Name
Model
CS1 CPU Bus Loop Control Unit CS1W-LC001
Units
Controller Link Units CS1W-CLK52-V1
CS1W-CLK21-V1
CS1W-CLK12-V1
SYSMAC LINK Unit CS1W-SLK21
CS1W-SLK11
Serial Communica- CS1W-SCU21
tions Unit
Ethernet Unit
CS1W-ETN01/11/21
DeviceNet Unit
CS1W-DRM21
PROFIBUS-DP
CS1W-PRM21
Master Unit
Consumption (A)
0.36
0.65
0.33
0.52
0.48
0.47
0.29
(See Note.)
0.40
0.29
0.40
Note: Add 0.15 A per port when the NT-AL001-E is connected.
Programmable Controllers
Category
Name
C200H Out- Relay Output
put Units
Units
Transistor Output
Units
CS1 Output Relay Output
Units
Units
C200H Spe- Analog Input Unit
cial I/O
Analog Output
Units
Units
Analog I/O Unit
ID Sensor Units
CS1 Special Analog Input Unit
I/O Units
Analog Output
Units
Analog I/O Unit
Isolated Thermocouple Input Unit
Isolated Temperature- resistance
Thermometer
Input Unit
Isolated Temperature- resistance
Thermometer
Input Unit
(Ni508.4 Ω)
Isolated Two-wire
Transmission
Device Input Unit
Isolated DC Input
Unit
Isolated Pulse
Input Unit
Isolated Control
Output Unit
Power Transducer
Input Unit
100-mV DC Input
Unit
Customizable
Counter Unit
RFID Sensor Unit
Duplex CPU units
Model
C200H-OC221
C200H-OC222
C200H-OC223
C200H-OC224
C200H-OC225
C200H-OC222N
C200H-OC226N
C200H-OC224N
C200H-OD216
C200H-OD217
CS1W-OC201
CS1W-OC211
C200H-AD003
C200H-DA003
C200H-DA004
C200H-MAD01
C200H-IDS01-V1
C200H-IDS21
[email protected]@@-V1
CS1W-DA041
CS1W-DA08V
CS1W-DA08C
CS1W-MAD44
CS1W-PTS01
CS1W-PTS11
CS1W-PTS02
CS1W-PTS12
0.10
0.20
0.25
0.20
0.12
0.12
0.10
0.18
0.18
0.25
0.20
0.15
0.08
0.15
0.07
CS1W-PTS03
0.15
CS1W-PTW01
0.16
CS1W-PDC01
CS1W-PDC11
CS1W-PPS01
0.12
0.16
Programmable
Controllers
26-V Current Consumption
Consumption (A)
0.075 for 8 points ON at
the same time
0.09 for 8 points ON at
the same time
0.075 for 8 points ON at
the same time
0.006 for each point ON
at the same time
CS1W-PMV01
CS1W-PTR01
0.08
CS1W-PTR02
CS1W-HCA22
0.15
[email protected]
0.12
279
[email protected]@@-E
C200H-series CPU units
SYSMAC HX/HG/HE PLCs with Information Control Functions for More “Intelligent” Production Lines
• Simple serial connections for Higher Development Efficiency
• Built-in protocol macro function
• Special I/O Units
• 2- or 4-axis Motion Control Unit, Controller Link Unit, CompoBus/
S Unit, DeviceNet Unit, PROFIBUS-DP Units, Eight-point Analog
I/O Unit, etc.
• SYSMAC C200HX/HG/HE-ZE with Increased Memory
Capacity and Instructions Added to the Line-up.
• Memory capacity up to 63.2 kWords (C200HX-CPU65/85-ZE).
• EM Area up to 16 banks of 6 kWords each (C200HX-CPU85-ZE).
• More than 70 types of symbolized compare and arithmetic
instructions added.
• Direct designation possible for one bank of the EM Area.
280
Programmable Controllers
Additional Basic PLC Functions
The SYSMAC C200HX/HG/HE PLCs are equipped with the Protocol
Macro function that incorporates communications programs into the
ladder program using only a few ladder instructions. This function
allows data communications with measurement devices and peripheral
devices. A variety of workplace data can be processed in real time
improving product quality and reducing total product cost. System
development time can be reduced substantially.
The SYSMAC C200HX/HG/HE PLCs offer improved basic functions
and performance such as memory capacity and processing speed. This
reinforces their use as machine controllers, and also lets you respond
more flexibly to advanced information applications on the production
floor.
ASCII Unit unnecessary
SYSMAC
200HX/HG/HE
The number of I/O points has been increased from 640 to 1,184. This
is a maximum of 1.4 times as many I/O points as the SYSMAC
C200HS, and gives you an extra margin of control.
Several ladder
instructions
PLC's CPU
Unit
A Large Increase in I/O Points
Component
Standard serial communications
Communications
Board
(Temperature Controller,
BCR, ID, etc.)
Note: An optional Communications Board (C200HW-COM04-E/05-E/
06-EV1) is required to use the Protocol Macro function.
Windows-based Protocol Support Software
Protocol macro instructions can be customized with the CX-Protocol
Protocol Support Software. This makes it easy to modify standardequipped protocols and and register them for use anytime.
I/O Points
SYSMAC C200HX/HG/HE(-ZE)
1,184 max.
C200HS
880
Faster Processing
Basic instructions are processed in 0.1 µs. Compared with the SYSMAC C200HS, processing speed is a maximum of 3.75 times faster.
Faster processing shortens production throughput and results in
increased productivity.
Processing Speed
SYSMAC C200HX/HG/HE (-ZE)
0.1 µs
C200HS
0.375 µs
Larger Memory Capacity
The SYSMAC C200HX/HG/HE PLCs provide 3.2 to 63.2 kWords of
program memory and 4 to 24 kWords of data memory. Compared with
the SYSMAC C200HS, capacity is a maximum of 2 to 4 times greater.
This level of capacity makes it easy to handle even large programs.
Memory Capacity
Improved Special I/O Units
The number of Special I/O Units that can be mounted on the CPU Unit
has been increased from 10 max. to 16 max. to take further advantage
of the capabilities of the C200HX/HG PLCs. The controlled system can
be managed easily with the right combination of Special I/O Units. The
INTELLIGENT I/O READ and INTELLIGENT I/O WRITE instructions
can be executed to transfer more than one word of data. All of the Special I/O Units compatible with the C200HS can be used as they are. In
addition, a PC Card Unit, Motion Control Unit, and Eight-point Analog I/
O Unit have been added. The SYSMAC C200HX/HG/HE PLCs are
becoming increasingly powerful and user-friendly.
SYSMAC C200HX/HG/HE(-ZE)
63.2 Kwords max.
C200HS
15.2 Kwords
More Banks in the EM Area
The maximum of three banks in previous models has been increased
to a maximum of 16 (using the C200HX-CPU85-ZE). In the SYSMAC
C200HX/HG/HE-ZE, one of those banks can be directly designated.
Combined with the conventional 6 kWords of data memory, this allows
direct use of 12 kWords.
Note: There are restrictions on the Units that can be used.
C200H-series CPU units
281
Programmable
Controllers
A Built-in Protocol Macro Function
System Configuration
Basic Configuration
Two or three* Expansion I/O Racks can be connected to the CPU Rack
for the SYSMAC C200HX, C200HG, and C200HE.
Note: Only for the C200HG-CPU53/63(-ZE) and C200HX-CPU54/64/
65/85(-ZE).
CPU
Rack
I/O
Connecting
Cable
Expansion
I/O Racks
Model
ProDM
EM (words)
gram ca- (words)
pacity
(words)
Basic
No of
instruction I/O
processing points
time
Max. no.
of connecting
Expansion I/O
Racks
C200HE-CPU11(-Z)E 3.2K
4K
None
0.3 ms min.
640
2
C200HE-CPU32(-Z)E
C200HE-CPU42(-Z)E
C200HG-CPU33(-Z)E
C200HG-CPU43(-Z)E
C200HG-CPU53(-Z)E
C200HG-CPU63(-Z)E
C200HX-CPU34(-Z)E
7.2K
7.2K
15.2K
15.2K
15.2K
15.2K
31.2K
6K
6K
6K
6K
6K
6K
6K
0.3 ms min.
0.3 ms min.
0.15 ms min.
0.15 ms min.
0.15 ms min.
0.15 ms min.
0.1 ms min.
880
880
880
880
1,184
1,184
880
2
2
2
2
3
3
2
C200HX-CPU44(-Z)E 31.2K
6K
0.1 ms min.
880
2
10
5
10
5
Yes
Yes
Yes
C200HX-CPU54(-Z)E 31.2K
6K
0.1 ms min.
1,184
3
16
8
16
8
No
Yes
Yes
C200HX-CPU64(-Z)E 31.2K
6K
0.1 ms min.
1,184
3
16
8
16
8
Yes
Yes
Yes
C200HX-CPU65-ZE
63.2K
6K
0.1 ms min.
1,184
3
16
8
16
8
Yes
Yes
Yes
C200HX-CPU85-ZE
63.2K
6K
None
None
6K
6K
6K
6K
6K x
3 banks (18K)
6K x
3 banks (18K)
6K x
3 banks (18K)
6K x
3 banks (18K)
6K x
8 banks (48K)
6K x
16 banks
(96K)
Max. no. of
connecting
High-density I/O
Units (Group-2)*
Units
Units
that
that
are allo- are allocated
cated
memo- memory for
ry for
1 Unit 2 Units
Unavail- Unavailable
able
10
5
10
5
10
5
10
5
16
8
16
8
10
5
Max. no. of
RS-232C Clock
Availconnecting Special
function ability
I/O Units*
of
Communications
Units
Units
Board
that are that are
allocated allocated
memory memory
for 1 Unit for 2
Units
0.1 ms min.
1,184
3
16
8
16
8
Yes
Yes
Yes
10
5
No
No
No
10
10
10
10
16
16
10
5
5
5
5
8
8
5
No
Yes
No
Yes
No
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Note: There are restrictions on the number of High-density I/O Units and Special I/O Units that can be mounted per CPU Unit. When mounting,
the unit number for each of the Units is set using the rotary switches on the front of the Units. When mounting 16 Units to a CPU Unit (to
which 16 Units can be mounted), unit numbers are set from 0 to F. When mounting 10 Units to a CPU Unit (to which 10 Units can be
mounted), unit numbers are set from 0 to 9; they cannot be set from A to F. When mounting 16 Units to a CPU Unit (to which 16 Units can
be mounted), unit numbers can be set from 0 to F for the following Units:
Special I/O Units
Analog Units: C200H-AD002, C200H-AD003, C200H-DA002, C200H-DA003, and C200H-DA004
High-speed Counter Unit: C200H-CT021
Position Control Unit: C200H-NC211 (allocated memory for 2 Units)
MC Unit: MC221 (allocated memory for 2 Units)
High-density I/O Units (Group-2)
32-point Units: C200H-ID216 and C200H-OD218
64-point Units: C200H-ID111, C200H-ID217, and C200H-OD219 (allocated memory for 2 Units)
With Units other than those listed above, the unit number can only be set in the range 0 to 9 and so only the memory corresponding to
these unit numbers can be allocated. Even with CPU Units to which 16 Units can be mounted, the unit number cannot be set up to 16 if a
Unit such as the C200H-ID215 Input Unit is used, and so if only this Unit is used, it is not possible to mount 16 Units to the CPU Unit. With
Units that are allocated memory for 2 Units, 2 unit numbers are allocated per Unit (i.e., 0, 2, 4, etc.). For example, although 16 Units can
normally be mounted to the C200HX-CPU64, if only MC Units are used, the maximum number of mountable Units is 8. When used in combination with 12 C200H-AD003 Analog Units, although 4 High-speed Counter Units can be mounted, only 2 MC Units can be mounted. The
unit number is set for the [email protected] B7A Unit in the same way as for a High-density I/O Unit (Group-2).
282
Programmable Controllers
CPU Backplane
Model
C200HW-PA204
C200HW-PA204S
C200HW-PA204R*
C200HW-PD024
Supply voltage
100 to 120 V AC
200 to 240 V AC
100 to 120 V AC
200 to 240 V AC
100 to 120 V AC
200 to 240 V AC
24 V DC
Comments
--With 24- V DC service power supply
With output
contacts during
operation
---
*There are restrictions on the CPU Units or Backplanes with which the C200HW-PA204R and C200HWPA209R Power Supply Units can be used. Refer to the
following tables for details.
Model Legend
@@@@
Model
C200HW-BC031
C200HW-BC051
C200HW-BC081
C200HW-BC101
Programmable
Controllers
Power Supply Unit
No. of I/O slots
3
5
8
10
I/O Backplane
The I/O Backplane is used to mount Expansion I/O Racks.
(See page ntlp.) Four models are available, each with a different
number of I/O slots.
Model
C200HW-BI031
C200HW-BI051
C200HW-BI081
C200HW-BI101
No. of I/O slots
3
5
8
10
Year (Example: 1997: 7)
Month (January to September: 1 to 9;
October to December: X to Z)
Day (01 to 31)
CPU Units that Support C200HW-PA204R
Model
C200HX-CPU64-E
C200HX-CPU54-E
C200HX-CPU44-E
C200HX-CPU34-E
C200HG-CPU63-E
C200HG-CPU53-E
C200HG-CPU43-E
C200HG-CPU33-E
C200HE-CPU42-E
C200HE-CPU32-E
C200HE-CPU11-E
Serial number
Made in Japan
Beginning with 20Z6
Beginning with 2817
Beginning with 19Z6
Beginning with 2417
Beginning with 25Z6
Beginning with 0817
Beginning with 19Z6
Beginning with 1017
Beginning with 20Z5
Beginning with 19Z6
Beginning with 20Z6
Made in Netherlands
Beginning with 0147
I/O Connecting Cable
These cables are used to connect a CPU
Unit to an Expansion I/O Rack, or to connect
two Expansion I/O Racks. Select cables
from among the following five types, and use
them in combination when necessary. The
total cable length must be within 12 m.
Model
C200H-CN311
C200H-CN711
C200H-CN221
C200H-CN521
C200H-CN131
Length
30 cm
70 cm
2m
5m
10 m
CPU Backplanes that Support C200HW-PA204R
Model
C200HW-BC031
C200HW-BC051
C200HW-BC081
C200HW-BC101
Serial number
Made in Japan
Beginning with 0617
Beginning with 19Z6
Beginning with 24Z6
Beginning with 20Z6
C200H-series CPU units
Made in Netherlands
Beginning with 0147
283
Communications Board
Communications Board
By mounting an appropriate type of Communications Board to an optical slot of the CPU Unit, the CPU Unit can communicate with the SYSMAC LINK Unit Programmable Terminal, Temperature Controller,
personal computer, barcode reader, or any other peripheral device via
RS-232C, RS-422, or RS-485.
Model
C200HW-COM01
C200HW-COM02-V1
C200HW-COM03-V1
C200HW-COM04-EV1
C200HW-COM05-EV1
C200HW-COM06-EV1
Specifications
Communications port for Controller Link, SYSMAC
LINK Units
One RS-232C port
One RS-422/485 port
Communications port for the Controller Link, SYSMAC LINK Units, one RS-232C port, and a protocol
macro function
Two RS-232C ports and a protocol macro function
One RS-422/485 port, one RS-232C port, and a protocol macro function
Models Available
The following Communications Board models are available.
Indicators
Bus
connector
Port A
(RS-232C)
C200HW-COM01
C200HW-COM02-V1
Indicators
Indicators
Bus
connector
Port A
(RS-422/485)
C200HW-COM03-V1
C200HW-COM04-EV1
Indicators
Indicators
Port B
(RS-232C)
Port B
(RS-232C)
Port A
(RS-232C)
Port A
(RS-422/485)
C200HW-COM05-EV1
284
Port A
(RS-232C)
C200HW-COM06-EV1
Programmable Controllers
Protocol Macro Function
Summary
Improved Communications Board Functions (-V1 Models)
The protocol macro consists of PMCR ladder instructions for communications sequences used to exchange data with a variety of peripheral
devices connected to the RS-232C or RS-422/485 port.
The following functions have been added to [email protected]
Communications Boards.
• SUM2 (2’s complement of SUM) and CRC-16 are added as error
check codes.
• Repeat counter N’s current value, Sequence End Completion Flag,
and Sequence Abort Completion Flag are added to the Auxiliary
Area.
• A check code can be located after the terminator as an additional
message item.
• Possible to swap between the leftmost and rightmost bytes of error
check codes.
Supported Communications Sequences
The Protocol Support Software and Communications Boards (i.e., the
C200HW-COM04-EV1, C200HW-COM05-EV1, and C200HWCOM06-EV1) support the following seven types of standard communications sequences. Communications sequences other than those
listed below can be created using the Windows-based CX-Protocol
Protocol Support Software (purchased separately).
1
2
3
4
5
6
7
Sequence
Temperature Controller
Intelligent Signal Processor
Bar Code Reader
Laser Micrometer
Visual Inspection System
ID Controller
Hayes AT Command (Modem)
Model No.
[email protected], [email protected], [email protected], E5ZE
K3TH, K3TR, K3TX, K3TC
V500, V520
3Z4L
F200, F300, F350
V600
ME 1414BZ, MD 24FB10V, MD 144FB5V
●
[email protected]@
CX-Programmer
PLC Programming Tool
●
WS02-PSTC1-E
CX-Protocol
Protocol Support Tool
C200HW-COM04/05/06-EV1
Communications Board
(with protocol macro function)
Standard measuring devices,
components, and personal
computers
C200HX/HG/HE
RS-232C
or
RS-422/485
Asynchronous (start-stop synchronization) communications
OMRON's peripheral devices (equipped with standard communications sequences)
ID Controller
Visual Inspection
System
Temperature Controller
Modem
Laser micrometer
Intelligent Signal Processor
Bar code reader
C200H-series CPU units
285
Programmable
Controllers
PMCR Ladder Instructions Let You Easily Exchange Data between Peripheral Devices
E5AJ Temperature Controller Connection Example
Connections
Communications Board (with protocol macro function)
C200HW-COM06-EV1
C200HX/HG/HE
Port A
(RS-422/485)
RS-422
#0
#1
#2
#3
E5AJ-A2H02
E5AJ-A2H02
E5AJ-A2H02
E5AJ-A2H02
Program Example
In this example, the E5AJ is set to a target value.
Start
condition
PMCR
Execute Flag
@PMCR
#1205
D0506
D1000
Port A specification with communications sequence 205
Setting Units and Values
DM word
D0506
D0507
D0508
Set data
0003
0003
0085
Meaning
No. of words for transmission data
Unit No.
Target value (85°C)
End Code:
This communications sequence is set to any word because there is
no reception data for the communications sequence.
Examples of Sequences Available
Sequence
number
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
286
Communications sequence name
Function
Remote mode select
Local mode select
Backup mode select
RAM write mode select
Target value save
Set value write 1
Set value write 2
Input compensation value write
Set value read 1
Set value read 2
Input compensation value read
Output read
Process value read
Target value limit read
Heater current read
Initial status read
General-purpose write
General-purpose read
Sets the Unit to remote mode.
Sets the Unit to local mode.
Changes target value write mode into backup mode.
Changes target value write mode into RAM write mode.
Saves the target value.
Writes the target value, alarm value 1, alarm value 2, and heater burnout alarm value all together.
Writes the proportional band, integral time, and derivative time all together.
Writes the input compensation value.
Reads the target value, alarm value 1, alarm value 2, and heater burnout alarm value all together.
Reads the proportional band, integral time, and derivative time all together.
Reads the input compensation value in the IOM.
Reads and saves the output in the IOM.
Reads and saves the process value in the IOM.
Reads and saves the target value limit in the IOM.
Reads and saves the heater current in the IOM.
Reads and saves the initial status in the IOM.
Writes the designated set value by setting the header code.
Reads the designated set value by setting the header code.
Programmable Controllers
Item
Supply voltage
Specifications
AC power supply:100 to 120/200 to 240 V AC selectable 50/60 Hz
DC power supply:24 V DC
AC power supply:85 to 132/170 to 264 V AC
DC power supply:19.2 to 28.8 V DC
AC power supply:120 VA max.
DC power supply:50 W max.
30 A max.
4.6 A, 5 V DC; 0.6 A, 26 V DC; <0.3 A: +17%/–11%/≥0.3 A: +10%/–11%
24 V DC+10%/–20% (C200HW-PA204S only)
SPST-NO, 1 A at 250 V AC/24 V DC (Only the C200HW-PA204R has terminal output.)
20 MΩ between AC terminals and the GR terminal at 500 V DC (see note 1)
2,300 V AC at 50/60 Hz for 1 minute between AC terminals and housing; 1,000 V AC at 50/60 Hz for 1 minute between DC
terminals and housing. Leakage current: 10 mA max. (see note 1)
Conforms to IEC61000-4-4, 2 kV (power lines)
10 to 57 Hz; 0.075 mm amplitude, 57 to 150 Hz (see note 2); acceleration: 9.8 m/s2, in X, Y, and Z directions, for 80 minutes
each (sweep time 8 min x 10 sweeps = 80 min); (When mounted on DIN rail, 2 to 55 Hz, 2.9 m/s2, in X, Y, and Z directions
for 20 minutes each)
147 m/s2 in X, Y, and Z directions, 3 times each
Operating: 0 to 55°C
Storage: –20 to 75°C (without battery)
10% to 90% (without condensation)
Must be free of corrosive gases
Less than 100 Ω
IEC IP30 (mounted in a panel)
6 kg max. (CPU Unit: 315 g max., Power Supply Unit: 510 g max., Backplane: 445 g to 1040 g)
Operating voltage range
Power consumption
Surge current
Output capacity
Operation output
Insulation resistance
Dielectric strength
Noise immunity
Vibration
Shock
Ambient temperature
Humidity
Atmosphere
Grounding
Enclosure rating
Weight
Note: 1. Be sure to disconnect the LG and GR terminals when conducting insulation resistance tests or dielectric strength tests.Internal components might be damaged if insulation resistance tests are repeated many times with the LG and GR terminals connected.
2.
Acceleration (G)
9.8
Amplitude
0.075 mm
Frequency (Hz)
10
C200H-series CPU units
57
150
287
Programmable
Controllers
General Specifications
Dimensions
CPU Rack
RDY
COMB
COMA
RUN
ERR
INH
COMM
POWER
SYSMAC C200HX
PROGRAMMABLE CONTROLLER
CPU64
130 118
(130)
Backplane
C200HW-BC031 (3 slots)
C200HW-BC051 (5 slots)
C200HW-BC081-V1 (8 slots)
C200HW-BC101-V1 (10 slots)
A
246
316
421
491
W
260
330
435
505
A
W
118
Expansion I/O Rack
130 118
(130)
Backplane
C200HW-BI031 (3 slots)
C200HW-BI051 (5 slots)
C200HW-BI081-V1 (8 slots)
C200HW-BI101-V1 (10 slots)
A
175
245
350
420
W
189
259
364
434
A
W
118
Characteristics
Item
Control method
I/O control method
Programming method
Instruction length
Number of instructions
Execution time
Program capacity
I/O bits
IR bits
SR bits
TR bits
HR bits
AR bits
LR bits
Timers/Counters
DM words
EM words
Power failure backup function
Memory backup time
Self-diagnostic function
Program check function
288
Specifications
Stored program
Cyclic scan with direct output and immediate interrupt processing are both possible.
Ladder diagram
1 address/instruction, 1 to 4 words/instruction
14 basic instructions, 231 special instructions
(281 special instructions for [email protected]@-ZE CPU Units.)
Basic instructions:
e.g., LD
[email protected]@-(Z)E:0.3 µs
[email protected]@-(Z)E:0.15 µs
[email protected]@-(Z)E:0.1 µs
Special instructions:
e.g., MOV(21)[email protected]@-(Z)E:1.2 µs
[email protected]@-(Z)E:0.6 µs
[email protected]@-(Z)E:0.4 µs
C200HE-CPU11-(Z)E:3.2 kWords max.
C200HE-CPU32-(Z)E/CPU42-(Z)E:7.2 kWords max.
[email protected]@-(Z)E:15.2 kWords max.
[email protected](Z)E:31.2 kWords max.
C200HX-CPU65-ZE/CPU85-ZE:63.2 kWords max.
640 (00000 to 02915, 30000 to 30915)
6,528 (03000 to 23515, 31000 to 51115)
1,080 (23600 to 25507, 25600 to 29915)
8 (TR 0 to 7)
1,600 (HR 0000 to 9915)
448 (AR 0000 to 2715)
1,024 (LR 0000 to 6315)
512 (TIM/CNT 000 to 511)
Read/Write: 6,144 (DM 0000 to 6143)
Read-only: 512 (DM 6144 to 6655)
Expansion: Up to 3,000 words max. (DM 7000 to 9999)
Read/Write:
[email protected]@-(Z)E: None
[email protected]@-(Z)E: 6,144 (EM 0000 to EM 6143)
[email protected]@-(Z)E: 6,144 (EM 0000 to EM 6143) ×3 banks
C200HX-CPU65-ZE: 6,144 (EM 0000 to EM 6143) ×8 banks
C200HX-CPU85-ZE: 6,144 (EM 0000 to EM 6143) ×16 banks
Holds HR, AR, CNT, DM, and EM and clock (RTC) contents.
The battery service life is five years at 25°C. The service life will be shortened if the battery is used at higher temperatures.
Replace the battery within one week after the battery alarm indicator starts flashing. When replacing the battery, install the new
battery within five minutes after removing the old one.
CPU Unit errors (watchdog timer), I/O verification errors, host link errors, memory errors, battery errors, I/O bus errors,
remote I/O errors, etc.
Checks the program from the time the program starts running and checks the omission of the END instruction or any other
improper instruction. This function allows three-level checking of programs through the Programming Console.
Programmable Controllers
Unit
I/O Units
Input Units
Classification
CS1 Basic I/O Unit
C200H Basic I/O Unit
Output Units
C200H Special I/O Unit
CS1 Basic I/O Unit
C200H Basic I/O Unit
I/O Units
High-speed Input Unit
Interrupt Input Unit
Analog Timer Unit
B7A Interface Units
Safety Relay Unit
Analog I/O Units
Input Units
Output Units
I/O Units
Input Units
Output Units
Analog I/O Units
Loop Control Unit
Process I/O Units
Temperature Sensor Units
Temperature Control Units
Heat/Cool Control Units
PID Control Units
Cam Positioner Unit
Position Control Units
Motion Control Unit
High-speed Counter Units
Customizable Counter Units
ID Sensor Units
ASCII Units
Serial Communications
Boards/Unit
Serial Communications Boards
Serial Communications Unit
RS-232C/RS-422 Conversion Unit
GP-IB Interface Unit
Ethernet Unit
Controller Link Boards/
Controller Link Unit
Unit
Controller Link Boards
PROFIBUS-DP Units
PROFIBUS-DP Master Unit
PROFIBUS-DP I/O Link Unit
DeviceNet Unit
Master Unit
I/O Link Unit
CompoBus/S Master Unit
CANopen/User-defined CAN Unit
DeviceNet and CompoBus/S Units
C200H Group-2 High Density Units
C200H Special I/O Unit
CS1 Basic I/O Unit
C200H Special I/O Unit
CS1 Basic I/O Unit
CS1 Basic I/O Unit
C2ooH Basic I/O Unit
C200H Special I/O Unit
C200H Basic I/O Unit
C200H Basic I/O Unit
C200H Basic I/O Unit
CS1 Basic I/O Unit
CS1 Special I/O Unit
C200H Special I/O Unit
CS1 Special I/O Unit
C200H Special I/O Unit
CS1 Basic I/O Unit
C200H Special I/O Unit
CS1 CPU Bus Unit
CS1 Special I/O Unit
CS1 Special I/O Unit
C200H Special I/O Unit
C200H Special I/O Unit
C200H Special I/O Unit
C200H Special I/O Unit
C200H Special I/O Unit
CS1 Special I/O Unit
C200H Special I/O Unit
CS1 Special I/O Unit
C200H Special I/O Unit
CS1 CPU Bus Unit
CS1 Special I/O Unit
C200H Special I/O Unit
CS1 Special I/O Unit
CS1 Special I/O Unit
C200H Special I/O Unit
C200H Special I/O Unit
Inner Board
CS1 CPU Bus Unit
----CS1 CPU Bus Unit
CS1 CPU Bus Unit
Personal computer ISA board
CS1 CPU Bus Unit
C200H Special I/O Unit
C200H Special I/O Unit
CS1 CPU Bus Unit
C200H Special I/O Unit
C200H Special I/O Unit
C200H Special I/O Unit
C200H Special I/O Unit
Model
[email protected]@
[email protected]
[email protected]
[email protected]
[email protected]
C200H-ID501
[email protected]
[email protected]@@
[email protected]@
[email protected](@)
[email protected](@)
[email protected]@@
[email protected]@
C200H-OD501
[email protected]@@
[email protected]@@
CS1W-IDP01
CS1W-INT01
C200H-INT01
C200H-TM001
C200H-B7AI1/12
C200H-B7AO1/02
C200H-B7A21/22
CS1W-SF200
[email protected]
C200H-AD003
CS1W-DA041/08V/08C
[email protected]
CS1W-MAD44
C200H-MAD01
CS1W-LC001
[email protected]
CS1D-LCB05D
[email protected]@[email protected]
[email protected]@
[email protected]@@
[email protected]@@
[email protected]@@
[email protected]
C200H-CP114
[email protected]@3
[email protected]@3
[email protected]
C200HW-MC402-E
CS1W-MCH71
[email protected]
CS1W-CTS21
C200H-CT021
[email protected]/-HIO01
[email protected]
C200H-IDS01-V1
[email protected]
[email protected]
CS1W-SCU21-V1
NT-AL001
CS1W-GPI01
[email protected]
[email protected]@-V1
[email protected]@-V1
CS1W-PRM21
C200HW-PRM21
C200HW-PRT21
CS1W-DRM21-V1
C200HW-DRM21-V1
C200HW-DRT21
C200HW-SRM21-V1
C200HW-CORT21-V1
Programmable
Controllers
CS1/C200H Unit Descriptions
Page
290
291
290
291
291
290
291
291
291
291
291
291
291
291
292
292
292
293
293
294
295
295
295
297
299
299
300
300
301
301
302
302
302
305
307
307
308
309
310
311
312
312
313
315
317
319
321
319
323
325
325
327
328
328
330
331
333
334
334
335
336
338
339
341
342
345
343
289
CS1 and C200H-series
Basic I/O Units
I/O Units
Input Unit
CS1W-ID211
16 points
Output Units
[email protected]
16 points
AC Input Units
[email protected]
16 points
Input Unit
CS1W-ID231
32 points
Output Units
[email protected]
32 points
Input Unit
CS1W-ID261
64 points
Output Units
[email protected]
64 points
I/O Units
[email protected]
32/32 points
Triac Output Unit
CS1W-OA201
8 points
Relay Output Unit
CS1W-OC201
8 independent
Triac Output Unit
CS1W-OA211
16 points
Relay Output Unit
CS1W-OC211
16 points
Input Unit
CS1W-ID291
96 points
Output Units
[email protected]
96 points
I/O Units
[email protected]
48/48 points
Input Unit
[email protected]@@@
8 points
Output Units
[email protected]@@@
5/8 points
Input Unit
[email protected]@@
32/64 points
Output Units
[email protected]@@@
32/64 points
Input Unit
[email protected]@@@
16 points
Output Units
[email protected]@@@
16 points
Input Unit
[email protected]@@
32 points
Output Units
[email protected]@@@
32 points
I/O Units
[email protected]@@@
16/16 points
DC Input Units
Classification
CS1 Basic I/O Unit
C200H Basic I/O Unit
C200H Group-2 I/O Units
C200H Special I/O Unit
Input voltage
24 V DC
Inputs
16 pts
24 V DC
24 V DC
24 V DC
32 pts
64 pts
96 pts
12 to 24 V DC
8 pts
24 V DC
16 pts
24 V DC
24 V DC
24 V DC
24 V DC
12 V DC
24 V DC
32 pts
64 pts
32 pts
64 pts
64 pts
32 pts
Connections
Removable terminal
block
Connector
Removable terminal
block
Removable terminal
block
Connector
Model
CS1W-ID211
Remarks
Input current: 7 mA
CS1W-ID231
CS1W-ID261
CS1W-ID291
Input current: 6 mA
C200H-ID211
Input current: approx.
5 mA
Input current: 10 mA
C200H-ID212
Input current: 7 mA
C200H-ID216
C200H-ID217
C200H-ID218
C200H-ID219
C200H-ID111
C200H-ID215
Input current: 4.1 mA
Input current: 6 mA
--Input current: 4 mA
TTL Input Units
Classification
C200H Special I/O Unit
290
Input voltage
5 V DC
Inputs
32 pts
Connections
Connector
Model
C200H-ID501
Remarks
Pulse-catch inputs
Programmable Controllers
Classification
CS1 Basic I/O Units
C200H Basic I/O Units
Input voltage
100 to 120 V AC, or 100 to 120 V DC
200 to 240 V AC
100 to 120 V AC
Inputs
16 pts
16 pts
8 pts
16 pts
200 to 240 V AC
8 pts
16 pts
Input voltage
12 to 24 V AC/ V DC
24 V AC/ V DC
Inputs
8 pts
16 pts
Outputs
8 pts (independent)
16 pts
8 pts
12 pts
12 pts
16 pts
16 pts
5 pts
8 pts
8 pts
Connections
Removable terminal block
Connections
Removable terminal block
Model
CS1W-IA111
CS1W-IA211
C200H-IA121
C200H-IA122
C200H-IA122V
C200H-IA221
C200H-IA222
C200H-IA222V
Connections
Removable terminal block
Model
C200H-IM211
C200H-IM212
Programmable
Controllers
AC Input Units (and 100 V DC)
AC/DC Input Units
Classification
C200H Basic I/O Units
Relay Output Units
Classification
CS1 Basic I/O Units
C200H Basic I/O Units
Model
CS1W-OC201
CS1W-OC211
C200H-OC221
C200H-OC222
C200H-OC222N
C200H-OC225
C200H-OC226N
C200H-OC223
C200H-OC224
C200H-OC224N
Transistor Output Units
Classification
CS1 Basic I/O Units
Outputs
16 pts
Max. switching capacity
12 to 24 V DC, 0.5 A/pt, 8 A/Unit sinking
24 V DC, 0.5 A/pt, 5 A/Unit, sourcing, short circuit protection, alarm
12 to 24 V DC, 0.5 A/pt, 5 A/Unit, sinking
24 V DC, 0.5 A/pt, 5 A/Unit, sourcing, short circuit protection, alarm
12 to 24 V DC, 0.3 A/pt, 6.4 A/Unit, sinking
24 V DC, 0.3 A/pt, 6.4 A/Unit, sourcing, short circuit protection, alarm
12 to 24 V DC, 0.1 A sinking, 7.2 A/Unit
12 to 24 V DC, 0.1 A sourcing, 7.2 A/Unit
12 to 48 V DC, 1 A sinking
24 V DC, 2.1 A, sinking
24 V DC, 0.8 A, sourcing, short circuit protection
5 to 24 V DC, 0.3 A, sourcing
24 V DC, 0.3 A, sinking
24 V DC, 0.3 A, sinking
5 to 24 V DC, 0.3 A, sourcing
24 V DC, 1.0 A, sourcing, short circuit protection
24 V DC, 0.3 A, sinking
16 mA at 4.5 V to 100 mA at 26.4 V, sinking
500 mA at 24 V DC, sourcing, short circuit protection
16 mA at 4.5 V to 100 mA at 26.4 V, sinking
16 mA at 4.5 V to 100 mA at 26.4 V, sinking
128-pt dynamic outputs possible
Connections
Removable
terminal block
Model
CS1W-OD211
CS1W-OD212
Connector
CS1W-OD231
CS1W-OD232
Outputs
32 pts
Max. switching capacity
5 V DC, 35 mA
128-pt dynamic outputs possible
Connections
Connector
Model
C200H-OD501
Outputs
8 pts
16 pts
8 pts
12 pts
12 pts
Max. switching capacity
250 V AC, 1.2 A, 50/60 Hz
250 V AC, 0.5 A, 50/60 Hz
250 V AC, 1.2 A, 50/60 Hz
250 V AC, 0.3 A, 50/60 Hz
250 V AC, 0.3 A, 50/60 Hz
Connections
Removable terminal block
Model
CS1W-OA201
CS1W-OA211
C200H-OA223
C200H-OA222V
C200H-OA224
32 pts
64 pts
96 pts
C200H Basic I/O Units
C200H Group-2 I/O Units
C200H Special I/O Unit
8 pts
8 pts
8 pts
8 pts
12 pts
16 pts
12 pts
16 pts
16 pts
32 pts
32 pts
64 pts
32 pts
CS1W-OD261
CS1W-OD262
Removable
terminal block
Connector
CS1W-OD291
CS1W-OD292
C200H-OD411
C200H-OD213
C200H-OD214
C200H-OD216
C200H-OD211
C200H-OD212
C200H-OD217
C200H-OD21A
C200H-OD212
C200H-OD218
C200H-OD21B
C200H-OD219
C200H-OD215
TTL Output Unit
Classification
C200H Special I/O Unit
Triac Output Units
Classification
CS1 Basic I/O Units
C200H Basic I/O Units
Basic I/O Units
291
Mixed I/O Units
Name
Classification
DC Input/ Transis- CS1 Basic I/O
tor Output Units
Units
Inputs/
Outputs
32 inputs/
32 outputs
32 inputs/
32 outputs
Input
voltage
24 V DC
48 inputs/
48 outputs
48 inputs/
48 outputs
C200H Spe- 16 inputs/
cial I/O Units 16 outputs
24 V DC
16 inputs/
16 outputs
24 V DC
12 V DC
Max. switching ca- Connections
pacity
12 to 24 V DC, 0.3 A, Connector
sinking
24 V DC, 0.3 A,
sourcing, load short
protection, alarm
12 to 24 V DC, 0.1 A,
sinking
12 to 24 V DC, 0.1 A,
sourcing
16 mA at 4.5 V to
100 mA at 26.4 V DC,
sinking
24 V DC, 50 mA,
sinking
Model
Remarks
CS1W-MD261
---
CS1W-MD262
---
CS1W-MD291
---
CS1W-MD292
---
C200H-MD215
Pulse-catch inputs,
128-pt dynamic outputs
possible
C200H-MD115
Note: In addition to the normal I/O functions, C200H High-density I/O Units (Special I/O Units) provide the following functions.
• Dynamic I/O (except for OD501/OD215): In stead of normal static inputs and normal static outputs, dynamic outputs and dynamic inputs
are used to increase I/O capacity to 128 inputs and 128 outputs through the use of strobe signal outputs. These functions can be used
to reduce wiring to devices with more digits, such as displays and keyboards.
• Pulse-catch Inputs (except OD501/OD215): Eight of the inputs can be set as pulse-catch inputs to reliably capture short pulses from
devices like photomicroswitches.
TTL I/O Unit
Name
Classification
TTL I/O Unit
CS1 Basic I/O Units
C200H Special I/O
Units
Inputs/ Outputs
16 inputs/
16 outputs
Input
voltage
5 V DC
Max. switch- Connections
ing capacity
5 V DC,
Connector
35 mA
Model
Remarks
CS1W-MD561
C200H-MD501
--Pulse-catch,
128-pt dynamic outputs possible
High-speed Input
Name
Pulse-catch Input Unit
292
Classification
CS1 Basic I/O Units
Inputs
16 pts
Max. switching capacity
24 V DC, 7 mA
Model
CS1W-IDP01
Programmable Controllers
Programmable
Controllers
CS1W-INT01, C200HS-INT01
Interrupt Input Units
Triggers interrupt task execution in the CPU
• When the CPU Unit receives an Input from the
Interrupt Input, the CPU Unit immediately suspends
execution of the Cyclic Task (Regular Program) and
executes the I/O Interrupt Task (CS1G/CS1H Only).
The Interrupt Input Unit operates as a regular Input
Unit in the CS1D PLCs.
• Mount the Interrupt Input Unit in the CPU Rack.
• Up to 2 CS1W-INT01 or 4 C200HS-INT01 Interrupt
Input Units can be mounted.
System Configuration
CPU Unit
I/O interrupt
task
Specifications
Classifications
CS1W Basic I/O Unit
Input voltage
24 V DC
Inputs
16 pts
C200H Basic I/O Unit
12 to 24 V DC
8 pts
Input pulse width
ON: 0.1 ms min.
OFF: 0.5 ms min.
ON: 0.2 ms max.
OFF: 0.5 ms max.
Connections
Removable terminal
block
Allocations
16 bits
(CIO 0319 to CIO 2000)
8 bits
Model
CS1W-INT01
C200HS-INT01
Note: The interrupt function can be used with the CPU Backplane only.
Interrupt Input Units
293
C200H-TM001
Analog Timer Unit
Easy On-site timer Adjustments
• Provides four timers easily adjusted on-site via
front-panel adjustments or external variable resistors: No Programming Device required. Using timer
pause inputs enables Usage as accumulative timer.
System Configuration
Analog Timer Unit
Timer set input
Timer pause input
Time up
outputs
T0
Set value
4 pts
Resistance
T3
Set value
Resistance
Specifications
Classification
Timers
C200H Basic
I/O Unit
4 pts
294
Setting range
Time setting method
CPU Unit bits
Allocations
(CIO 0319 to
CIO 2000)
0.1 to 1.0 s, 1 to 10 s, 2 to 60 s, Internal or external variable Timer set input, tim- 16 bits
1 to 10 min
resistor
er pause input, and
time up output
Model
C200H-TM001
Programmable Controllers
Programmable
Controllers
[email protected]@
B7A Interface Units
Multiplexing digital I/O units. Reduce wiring by transmitting 16 digital input
or output points over 2-wire point-to-point connections.
C200H-B7AI1 (16 inputs)
C200H-B7AO1 (16 outputs)
C200H-B7A02
(32 outputs)
C200H-B7A12
(32 inputs)
C200H-B7A21
(16 inputs/16 outputs)
C200H-B7A22
(32 inputs/32 outputs)
Connection Example
B7A: 32 inputs and 32 outputs
B7A: 16 inputs and 16 outputs
B7A: 32 outputs
B7A: 32 inputs
CS1 PLC
B7A Link Terminals
16 inputs
16 inputs
16 outputs
16 outputs
16 inputs
16 outputs
16 inputs
B7A Interface Units
16 inputs
16 outputs
16 outputs
295
Specifications
Item
I/O
capacity
B7A Interface Units
C200H-B7AI1
C200H-B7AO1
16 inputs or 15 + 1 er- --ror input
--16 outputs
500 m max. if separate power supplies are
used for Unit and Link Terminals.
100 m max. if same power supply is used for
Unit and Link Terminals.
Inputs
Outputs
Transmission distance
Transmission delay
19.2 ms typical, 31 ms max.
Internal current
consumption
External power supply (See
note 4.)
Weight
I/O word allocations
100 mA max. at 5 V DC
Note: 1.
2.
3.
4.
B7A Group-2 Interface Units
C200H-B7A12
C200H-B7A02
C200H-B7A21
C200H-B7A22
32 inputs
--16 inputs
32 inputs
(See note 1.)
(See note 2.)
(See note 1.)
--32 outputs
16 outputs
32 outputs
Normal operation:
500 m max. if separate power supplies are used for Unit Link Terminals.
100 m max. if same power supply is used for Unit Link Terminals.
High-speed operation:
100 m max. with shield connected and 10 m max. without shield connected if separate power supplies are used for Unit Link Terminals. 50 m max. with shield connected and 10 m
max. without shield connected if same power supply is used for Unit and Link Terminals.
Normal operation: 19.2 ms typical, 31 ms max.
HIgh-speed operation: 3 ms typical, 5 ms max. (See note 3.)
10 mA max. at 12 to 30 mA max. at 12 to 50 mA max. at 12 to 60 mA max. at 12 to 50 mA max. at 12 to 80 mA max. at 12 to
24 V DC ±10%
24 V DC ±10%
24 V DC ±10%
24 V DC ±10%
24 V DC ±10%
24 V DC ±10%
200 g max.
300 g max.
The unit number set with the I/O number setting switch on the front panel is invalid. I/O words are allocated consecutively according to
the mounting position, in the same way as with basic I/O Units.
Can also be used for 32 inputs or 30 inputs + 2 error inputs by changing input mode.
Can also be used for 16 inputs or 15 inputs + 1 error input by changing input mode.
Normal and high-speed operation set via switch.
Not including power supply to B7A Link Terminals
B7A Link Terminals
Input Terminals
Type
Screw terminals
Modules
PC connectors
Model
[email protected]
[email protected]
[email protected]
[email protected]
B7A-T6D2
B7A-T6D7
[email protected]
[email protected]
Transmission delay
Normal (19.2 ms)
High-speed (3 ms)
Normal (19.2 ms)
High-speed (3 ms)
Normal (19.2 ms)
High-speed (3 ms)
Output Terminals
Type
Screw terminal
Modules
PC connectors
Model
[email protected]@1
[email protected]@1
[email protected]@6
[email protected]@6
B7A-R6A52
B7A-RA57
[email protected]@3
[email protected]@8
Transmission delay
Normal (19.2 ms)
High-speed (3 ms)
Normal (19.2 ms)
High-speed (3 ms)
Normal (19.2 ms)
High-speed (3 ms)
For details, see page 439.
296
Programmable Controllers
Programmable
Controllers
CS1W-SF200
Safety Relay Unit
Reduced Wiring and Space for Safety
Circuits
• This Safety Relay Unit mounts as an I/O Unit and
provides both safety relays and inputs for monitoring.
• Safety relays and monitor inputs in 1 Unit to reduce
wiring and space.
• Safety relays operate with separate power supply
from PLC.
• Monitor safety circuit output, K1/K2 relay, or power
status from PLC.
• Four general-purpose inputs provided.
• Safety standards: EN954-1 and EN60204-1
Internal Connections
Specifications
General
Item
Contact resistance
Operating time
Response time
Indicator
Insulation resistance (See
note.)
Withstand voltage
(See note.)
Indicator
Durability
Weight
Indicator
Safety
circuits
Internal
circuits
Specifications
100 mΩ (5 V DC, 1 A, voltage drop method)
300 ms max. (not including bounce)
10 ms max. (time from input OFF to main contact
OFF, not including bounce)
20 MΩ min. (at 500 V DC) for following: Safety
circuits-safety outputs, General inputs-safety
outputs, Different poles of safety outputs, and
safety circuits-general inputs
2,500 V AC, 50/60 Hz for 1 min for following:
Safety circuits-safety outputs, General inputssafety outputs, Different poles of safety outputs
500 V AC, 50/60 Hz for 1 min for Safety circuitsgeneral inputs
Mechanical: 5,000,000 min. (7,200 time/hr)
Electrical: 100,000 min. (1,800 time/hr)
300 g
Note: Measured while mounted to PLC.
Ratings of Safety Circuits
Item
Power
Inputs
Switching
Supply voltage
Fluctuation
Consumption
Current
Rated load
Rated ON current
Specification
24 V DC
–15%/
+10% of supply voltage
24 V DC: 1.7 W max.
75 mA max.
250 V AC, 5 A
5A
Ratings of General Inputs
General
inputs
3.3 kΩ
0.01 µF
470 Ω
Input indicator
Safety Relay Unit
Item
Power voltage
Fluctuation
Input impedance
Input current
ON voltage/current
OFF voltage/current
ON/OFF response
Circuits
ON points
Specifications
24 V DC
–15%
/+10% of supply voltage
3.3 kΩ
7 mA typ. (24 V DC)
14.4 V DC min./3 mA min.
5 V DC max./1 mA max.
8 ms max. (Set to 1 to 32 in PC Setup)
4 points, 1 common
100% simultaneously ON
297
Analog I/O Selection Guide
Classification
Model
I/O
capacity
Analog Input
Units
CS1W-AD041-V1
8 inputs
Isolation
between
I/O points*
No
CS1W-AD081-V1
8 inputs
No
CS1W-PTW01
4 inputs
Yes
CS1W-PDC01
4 inputs
Yes
CS1W-PDC11
4 inputs
Yes
CS1W-PPS01
4 inputs
Yes
CS1W-PTR01
8 inputs
No
CS1W-PTR02
8 inputs
No
C200H-AD003
8 inputs
No
CS1W-DA041
4 outputs
No
CS1W-DA08V
4 outputs
No
CS1W-DA08C
CS1W-PMV01
4 outputs
4 outputs
No
Yes
CS1W-PMV02
4 outputs
Yes
C200H-DA001
C200H-DA002
C200H-DA003
2 outputs
4 outputs
8 outputs
No
No
No
C200H-DA004
CS1W-MAD44
8 outputs
No
4 inputs and No
4 outputs
C200H-MAD01
4 inputs and No
4 outputs
CS1W-PTS11
4 inputs
Yes
CS1W-PTS12
4 inputs
Yes
CS1W-PTS01-V1
4 inputs
Yes
CS1W-PTS02
CS1W-PTS03
C200H-TS001
C200H-TS002
C200H-TS101
C200H-TS102
4 inputs
4 inputs
4 inputs
4 inputs
4 inputs
5 inputs
Yes
Yes
No
No
No
No
Analog Output
Units
Analog I/O Unit
Temperature
Sensor Input
Units
I/O ranges/types
Conversion
time
Remarks
Page
1 to 5 V, 0 to 5 V,
0 to 10 V, ±10 V, 4 to 20 mA
1 to 5 V, 0 to 5 V,
0 to 10 V, ±10 V, 4 to 20 mA
1 to 5 V, 4 to 20 mA
0.25 ms/pt
---
299
0.25 ms/pt
---
100 ms/4 pts
Built-in power supply for 2-wire
transmission device,
measured value alarms
(HH, H, L, LL), other features
Measured value alarms
(HH, H, L, LL), other features
1 to 5 V, 0 to 5 V,
100 ms/4 pts
0 to 10 V, ±10 V, 4 to 20 mA,
0 to 20 mA
4 to 20mA, 0 to 20mA,
20 ms/4 pts,
0 to 10V, +/-10V, 0 to 5V, +/-5V, 10 ms/2 pts
1 to 5V, 0 to 1.25V, +/-1.25V
Max. counting speed: 20 K puls- --es/s (voltage input or no-voltage
semi-conductor input) or
20 pulses/s (contact input)
–1 mA to 1 mA, 0 to 1 mA
200 ms/8 pts
–100 mA to 100 mA,
0 to 100 mV
1 to 5 V, 0 to 10 V,
–10 to 10 V, 4 to 20 mA
1 to 5 V, 0 to 5 V,
0 to 10 V, ±10 V, 4 to 20 mA
1 to 5 V, 0 to 5 V,
0 to 10 V, ±10 V
4 to 20 mA
1 to 5 V, 4 to 20 mA
0 to 10 V, ±10 V, 0 to 5 V,
±5 V, 0 to 1 V, ±1 V
0 to 10 V, 1 to 5 V, 4 to 20 mA
–10 to 10 V, 4 to 20 mA
1 to 5 V, 0 to 10 V,
–10 to 10 V
4 to 20 mA
Inputs: 1 to 5 V, 0 to 5 V,
0 to 10 V, ±10 V, 4 to 20 mA
Outputs: 1 to 5 V, 0 to 5 V,
0 to 10 V, ±10 V
Inputs: 1 to 5 V, 0 to 5 V,
0 to 10 V, ±10 V, 4 to 20 mA
Outputs: 1 to 5 V, 0 to 5 V,
0 to 10 V, ±10 V
B, E, J, K, L, N, R, S, T, U,
WRe5-26, PLII, ±100 mV
Pt100Ω (JIS, IEC), JPt100Ω,
Pt50Ω, Ni508.4Ω
B, E, J, K, N, R, S, T,
±80 m V DC auto range
Pt100 (JIS, DIN, ISO) JPt100
Ni508Ω
K, J
K, L
JPt100
Pt100
305
Process value alarms (HH,H,L,LL)
Rate-of-change calculation and
alarm
Input disconnection detection
Top, bottom, valley hold
Accumulated value output
Variable range zero-span
adjustment
--306
1 ms/pt max.
Motor overdrive prevention,
measured value alarms (H, L),
other features
Measured value alarms (H, L),
other features
---
299
1 ms/pt
---
300
1 ms/pt
---
1 ms/pt
100 ms/4 pts
--Output disconnection alarm,
control output answerback input,
other features
---
200 ms/8 pts
40 ms/4 pts
306
306
300
2.5 ms/pt max.
1 ms/pt max.
1 ms/pt
---
301
1 ms/pt max.
20 ms/4 pts
10 ms/2 pts
150 ms/4 pts
100 ms/4 pts
100 ms/4 pts
4.8 s max.
4.8 s max.
4.8 s max.
4.8 s max.
Measured value alarms
305
(HH, H, L, LL), input disconnection
alarms, top hold, bottom hold,
valley hold, zero span adjustment
over user-set range, other features.
Automatic range setting, mea307
sured value alarms (HH, H, L, LL),
other features.
---------
307
Note: Inputs are isolated from PLC signals for all Units.
298
Programmable Controllers
Programmable
Controllers
[email protected], C200H-AD003
Analog Input Units
Convert Analog Signals to Binary Data
•
•
•
•
Wire burnout detection
Peak-hold function
Moving average filter function
Offset gain setting
Note: Analog Input Terminals are also available as
remote I/O terminals for DeviceNet, PROFIBUS-DP
or CompoBus/S.
Function
Circuit Configuration
Converts input signals such as 1 to 5 V or 4 to 20 mA to binary values
between 0000 and 0FA0 Hex and stores the results in the allocated
words each cycle. The ladder diagram can be used to transfer the data
to the DM Area or the SCALING instructions (e.g., SCL(194)) can be
used to scale the data to the desired ranges.
Specifications
Model
Classification
Unit number
Inputs
Signal
Voltages
range
Currents
1 to 5 V
0 to 10 V
0 to 5 V
–10 to 10 V
4 to 20 mA
0 to 20 mA
Signal range settings
Resolution
Conversion speed
Overall accuracy (at 25 °C)
Connections
Features Wire burnout detection
Peak-hold function
Mean function
CS1W-AD041-V1
CS1 Special I/O Units
0 to 95
4 pts
Yes
Yes
Yes
Yes
Yes
--4 settings
(one for each point)
1/8000
0.25 ms/pt max.
Voltage: ±0.2%
Current: ±0.4%
Terminal block
Yes
Yes
Yes
CS1W-AD081-V1
0 to 95
8 pts
Yes
Yes
Yes
Yes
Yes
--8 settings
(one for each point)
1/8000
0.25 ms/pt max.
Voltage: ±0.2%
Current: ±0.4%
Terminal block
Yes
Yes
Yes
C200HW-AD003
C200 Special I/O Units
0 to F
8 pts
Yes
Yes
--Yes
Yes
--8 settings
(one for each point)
1/4000
1 ms/pt. max
Voltage: ±0.2%
Current: ±0.4%
Terminal block
Yes
Yes
Yes
Note: Process I/O Units are also available for analog I/O. Refer to page 305.
Analog Input Units
299
[email protected], [email protected]
Analog Output Units
Convert Binary Data to Analog Signals
• Output limit
• Upper/Lower limit alarms
• Offset gain adjustment
Note: The functions provided depend in the model used.
Analog Output Terminals are also available as
remote I/O terminals for DeviceNet, PROFIBUS-DP
or CompoBus/S.
Function
Circuit Configuration
Binary data between 0000 to 0FA0 Hex in the allocated words is converted to analog signals such as 1 to 5 V or 4 to 20 mA for output. All
that is required in the ladder diagram is to place the data in the allocated
words.
Specifications
Model
Classification
Unit numbers
Outputs
Signal
Voltages
range
CS1W-DA041
CS1W-DA08V
CS1 Special I/O Units
0 to 95
0 to 95
4 pts
8 pts
1 to 5 V
Yes
Yes
0 to 10 V Yes
Yes
0 to 5 V
Yes
Yes
–10 to 10 V Yes
Yes
Currents 4 to 20 mA Yes
--0 to 20 mA ----Signal range settings
4 settings (one
8 settings (one
for each point)
for each point)
Resolution
1/4000
1/4000
0 to 95
8 pts
--------Yes
--8 settings (one
for each point)
1/4000
Conversion speed
Overall accuracy (at 25 °C)
1.0 ms/pt max.
±0.3% FS
1.0 ms/pt max.
±0.5% FS
Terminal block
Yes
Terminal block
Yes
1.0 ms/pt max.
Voltage:
±0.3%FS
Current:
±0.5%FS
Connections
Terminal block
Features Output hold function ---
CS1W-DA08C
C200H-DA001
C200H-DA002
C200H Special I/O Units
0 to 9
0 to F
2 pts
4 pts
Yes
--Yes
--------Yes
Yes
Yes
----1 setting (one for 4 settings (one
two points)
for each point)
1/4095
Voltage:
1/8190
Current:
1/4095
2.5 ms/pt max.
2.5 ms/pt max.
±0.5% FS
Voltage:
±0.3%FS
Current:
±0.5%FS
Terminal block
Terminal block
-----
C200H-DA003
C200H-DA004
0 to F
8 pts
Yes
Yes
--Yes
----8 settings (one
for each point)
1/4000
0 to F
8 pts
--------Yes
--8 settings (one
for each point)
1/4000
1.0 ms/pt max.
±0.3% FS
1.0 ms/pt max.
±0.5% FS
Terminal block
Yes
Terminal block
Yes
Note: Process I/O Units are also available for analog I/O. Refer to page 305.
300
Programmable Controllers
Programmable
Controllers
CS1W-MAD44, C200H-MAD01
Analog I/O Units
Analog Inputs and Outputs combined in
One Unit
•
•
•
•
•
Moving average filter function
Peak hold function
Wire burnout detection
Output hold function
Ratio conversions
Function
Circuit Configuration
One Unit performs both analog input and analog output operations. The
Unit can also be used for ratio and bias processing, which can be performed on analog inputs to output the results as analog outputs.
Specifications
Model
Classification
Unit numbers
Inputs
Outputs
Input signal ranges
Voltages
Output signal ranges Currents
Resolution
Conversion speed
Overall
accuracy
1 to 5 V
0 to 5 V
0 to 10 V
–10 to 10 V
4 to 20 mA
1 to 5 V
0 to 5 V
0 to 10 V
–10 to 10 V
4 to 20 mA
Inputs
Outputs
Connections
Features
Analog I/O Units
Mean function
Peak hold
Wire burnout detection
Output hold
Ratio conversion
C200H-MAD01
C200H Special I/O Unit
0 to F
2 pts
2 pts
Yes
--Yes
Yes
Yes
Yes
--Yes
Yes
Yes
1/4000 (inputs/outputs)
1.0 ms/pt max (inputs/outputs)
Voltage: ±0.2%
Current: ±0.4%
Voltage: ±0.3%
Current: ±0.5%
Terminal block
Yes
Yes
Yes
Yes
Yes
CS1W-MAD44
CS1 Special I/O Unit
0 to 95
4 pts
4 pts
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
--1/4000 (inputs/outputs)
1.0 ms/pt max (inputs/outputs)
Voltage: ±0.2%
Current: ±0.4%
Voltage: ±0.3%
Current: ±0.5%
Terminal block
Yes
Yes
Yes
Yes
Yes
301
CS1W-LC001, CS1W-LCB01/05, CS1D-LCB05D
Loop Control Unit
Process Values such as Temperature,
Pressure, and Flowrate can be controlled.
Supports Control Methods from Simple Loop
Control to Genuine Process Control.
• The control system can be scaled to match the controlled system, from a few loops that replace a Controller to hundreds of loops that perform large-scale
process control.
• A variety of control programs can be created by
selecting from more than 70 kinds of function blocks
suitable for loop control, such as PID calculations,
Segment Programs, and square root calculations.
• The CX-Process Tool can be used for easy programming.
• A Tuning Screen can be opened in the CX-Process
Tool to change parameters while monitoring the status.
• Duplex systems are available for applications that
require high reliability.
• The NS Face Plate Auto Builder software can
be used to automatically create a touch panel for
NS-series PTs from a function block screen.
Function
The CS1-series Loop Control Boards and Units are packed with DCS
functions and can use function block programs, which are ideal for process control. Graphical programming can be used, so function blocks
can be pasted into a window and connected with the mouse.
A wide variety of control methods can be executed, from regular PID
control to cascade control and feed-forward control.
System Configuration
NS-series PT
Create and transfer the
function block data with
the CX-Process Tool.
CS1-series PLC and
Loop Control Board/Unit
Analog I/O
302
Programmable Controllers
Programmable
Controllers
Function Block Example
Example: Cascade control
Analog
Analog
Input Unit Input Unit
Loop Control
Board/Unit
Function blocks
Isolated-type
AI4 terminal
Y1
Y2
Y3
Y4
PV1 PID1
MV1
RSP1
PV2 PID2
PID1
Basic PID
PV
PVE
RSP
MIE
MVE
SP
Y1
MV
Segment
Linearizer
X1
Y1
Isolated-type
AO4 terminal
Y1
X1
Y2
X2
Y3
X3
Y4
X4
MV2
Split
conversion
Basic PID
PV
PVE
RSP
MIE
MVE
Temperature
Temperature
Heat
exchanger
SP
Y1
MV
Segment
Linearizer
X1
Y1
Steam
PID2
Cold
water
Drain
Specifications
Item
Name
Unit type
Model
Specification
Loop Control Board
CS-series Inner Board
CS1W-LCB01 Standard CS1W-LCB05 AdInner Board
vanced Inner Board
Data stored in flash memory
Function block data, data in RAM (can be backed up or recovered at any
time), and error log data
0.8 ms max.
20 ms max.
(See note 2.)
220 mA at 5 V DC
Note: The current consumption is 150 mA higher when an NT-AL001 Link
Adapter is being used.
Loop Control Unit (See note 1.)
CS-series CPU Bus Unit
CS1D-LCB05D Duplex CS1W-LC001
Inner Board
(See note 3.)
Applicable PLCs
CS1G/[email protected]@F
CS1G/[email protected]@H
[email protected]@P
CS-series
(Duplex compatible)
Mounting location
CPU Unit’s Inner Board slot
CPU Rack
Max. number of Boards/Units
1 Board max. per CPU Unit
3 Units max. per CPU Unit
Data exchange
Allocation of specific words User Link Table function:
CPU terminal block:
with CPU Unit
in a data area
A function block’s ITEM data can be allocated to specified words in a CPU A function block’s ITEM data can be alloUnit data area (CIO, WR, HR, DM, or EM bank 0).
cated to any CPU Unit data area.
Allocation of all data
HMI Interface function:
Send/Receive All Blocks:
The ITEM data of a Control Block, Operation Block, or External Controller Can be allocated to any CPU Unit data
Block can be allocated to a specified EM bank. (The default EM bank is area (no default setting).
bank 0.)
Setting switches
None
Front panel rotary switches:
Unit number setting (0 to F)
Indicators
Three LED indicators:
Five LED indicators:
Running, Ready, and Comm. port sending/receiving
Running, Comm. port sending, Comm.
port receiving, CPU Unit error, and Unit
error
Front panel connectors
One RS-232C port (for connection of an ES100X External Controller)
Data Backup
Super capacitor backs up all function block data (including sequence
Battery backs up all function block data
tables and step ladder program instructions).
and contents of the error log.
Backup time of backup capacitor or battery
24 hrs at 25°C (The backup time is shorter at higher temperatures.)
5 years at 25°C (The battery life is shorter
at higher temperatures.)
Effect on the CPU Unit’s cycle time
Current consumption (supplied by the Power
Supply Unit)
Dimensions
Weight
Standard accessories
34.5 x 130 x 100.5 mm (W x H x D)
100 g max.
None
Function block data and data in RAM (can
be backed up or recovered at any time)
0.2 ms
360 mA at 5 V DC
Note: The current consumption is 150 mA
higher when an NT-AL001 Link Adapter is
being used.
220 g max.
C200H-BAT09 Battery Set
(factory installed in Unit)
Note: 1. The Loop Control Unit described in this table is equipped with the Version 2.5 functions.
2. The CPU Unit’s cycle time will be extended by 2.1 s max during duplex initialization.
3. The CS1D-LCB05D Duplex Loop Control Board is not available separately.
It can only be purchased in combination with a Duplex CPU as models CS1D-CPU65P or CS1D-CPU67P.
Loop Control Unit
303
Functional Specifications
Item
Model
Processing method
Operation cycle
Number of function Analog operations
blocks
Specifications
CS1W-LCB01
CS1W-LCB05/CS1D-LCB05D
Function block method
Available cycle settings (See note 1.):
0.01 s, 0.02 s, 0.05 s, 0.1 s, 0.2 s, 0.5 s, 1 s, and 2 s
(default setting is 1 s)
The operation cycle can be set for each function block.
CS1W-LC001
Available cycle settings:
0.1 s, 0.2 s, 0.5 s, 1 s, and 2 s
(default setting is 1 s)
The operation cycle can be set
for each function block.
32 blocks max.
Control Block (See 50 blocks max.
500 blocks max.
note 2)
Operation Block (See
249 blocks max.
note 3)
External Controller 32 blocks max. (excluding the CS1D-LCB05D)
Block
Sequence Control Sequence Table
None
Number of tables: 200
None
32 conditions and 32 operations
per table (When expanded, there
can be up to 64 conditions and 64
operations per table.)
Total: 6,400 rules
200 blocks max.
Step Ladder Block
20 blocks max.
2,000 instructions total
4,000 instructions total
100 instructions max. per block 100 instructions max. per block
Branch up to 100 steps max.
Branch up to 100 steps max.
I/O blocks
Field Terminal Block 80 blocks max.
User Link Table
2,400 data elements max.
None
Batch allocation
HMI function:
HMI function:
All blocks: send/receive
2,040 words max.
20,040 words max.
One block each max.
Allocated 1 bank of EM area.
Allocated 1 bank of EM area.
CPU Terminal Block None
16 blocks max.
NodeTerminal Block None
100 blocks max.
System Common Block
1 block
Function block creation/transfer method
Use the CX-Process Tool (sold separately) to create and transfer function blocks.
Control method
PID control method
PID control with two degrees of freedom (with autotuning function)
Combinable control methods
Can be accomplished by combining function blocks such as basic PID control, cascade control,
feed-forward control, sample PI control, Smith dead-time compensation control, PID control with
differential gap, override control, programmed control, and time-proportional control.
Alarms
Alarms within PID Blocks
There can be up to 4 PV Alarms (HH, H, L, and LL) and 1 Deviation Alarm per PID Block.
Alarm Blocks
High/Low Alarm Block and Deviation Alarm Block
Note: 1. The CS1D-LCB05D does not support the 0.01 s, 0.02 s, and 0.05 s settings.
2. Control Blocks perform control functions such as PID control.
3. Operation Blocks perform processing operations such as alarm operations, square root operations, time operations, and pulse-train
operations.
304
Programmable Controllers
Programmable
Controllers
[email protected]@@@
Process I/O Units
Wide variety of built-in signal conversion
functions for direct process signal inputs.
• External converters and transducers not required:
Greatly reduces costs, space requirements, and
labor.
• Receives temperature and other analog inputs.
Supports measured value alarms and rate-ofchange operation and alarms.
• Control outputs can be limited with the output
rate-of-change limit and output high/low limit.
• The [email protected]@[email protected] can limit measured values with
peak/bottom hold and top/valley hold functions.
• The [email protected]@[email protected] can count the number of
times that a preset threshold value is exceeded and
totalize analog values.
Function
Choose from a total of 13 models, including 11 isolated-type models, to handle essentially all normal data collection and process control
applications. High-speed (10 ms) and high-resolution (1/64,000) models are available for use in a wide range of applications, from data logging
to high-speed temperature control.
Specifications
Unit name
I/O
capacity
CS1W-PTS01-V1 4 inputs
Field I/O
isolation
All inputs
isolated.
CS1W-PTS11
4 inputs
All inputs
isolated.
CS1W-PTS02
Isolated-type
Temperature-resistance
Thermometer Input Unit
4 inputs
All inputs
isolated.
CS1W-PTS12
4 inputs
All inputs
isolated.
Isolated-type
CS1W-PTS03
Temperature-resistance
Thermometer Input Unit
(Ni508.4 Ω)
4 inputs
All inputs
isolated.
Isolated-type
Thermocouple
Input Unit
Process I/O Units
Model
I/O range/type
Accuracy/effective resolution
Main features
B, E, J, K, N, R, S, T, ±80 m Standard accuracy: ±0.1%
V DC variable range
Temp coefficient: ±0.015%/°C
Resolution: 1/4,096
Conversion cycle: 150 ms/4 pts
Variable range setting,
output scaling (±32,000),
measured value alarms
(HH, H, L, LL), rate-ofchange operation and
alarms, input disconnection alarms
B, E, J, K, L, N, R, S, T, U, Standard accuracy: ±0.05% of full Output scaling, measured
WRe5-26,PL II, ±100 mV
scale
value alarms (HH, H, L,
Temp coefficient: ±0.01%/°C
LL), rate-of-change operaEffective resolution: 1/64,000
tion and alarms, input disConversion cycle: 20 ms/4 pts
connection alarms, top
10 ms/2 pts
hold, bottom hold, valley
hold, zero span adjustment over user-set range
Pt100 (JIS, IEC) JPt100
Standard accuracy: Larger of ±0.1% Variable range setting,
or ±0.1°C
output scaling (±32,000),
Temp coefficient: ±0.015%/°C
measured value alarms
Resolution: 1/4,096
(HH, H, L, LL), rate-ofConversion cycle: 100 ms/4 pts
change operation and
alarms, input disconnection alarms
Pt100Ω (JIS, IEC), JPt100Ω, Standard accuracy: Larger of
Output scaling, measured
Pt50Ω, Ni508.4Ω
±0.05% of full scale or ±0.1°C
value alarms (HH, H, L,
Temp coefficient: ±0.01%/°C
LL), rate-of-change operaEffective resolution: 1/64,000
tion and alarms, input disConversion cycle:20 ms/4 pts
connection alarms, top
10 ms/2 pts
hold, bottom hold, valley
hold, zero span adjustment over user-set range
Ni508.4Ω
Standard accuracy: Larger of ±0.2% Variable range setting,
or ±0.2°C
output scaling (±32,000),
Temp coefficient: ±0.015%/°C
measured value alarms
Resolution: 1/4,096
(HH, H, L, LL), rate-ofConversion cycle: 100 ms/4 pts
change operation and
alarms, input disconnection alarms
305
Unit name
Model
CS1W-PTW01
I/O
capacity
4 inputs
Field I/O
isolation
All inputs
isolated.
I/O range/type
Accuracy/effective resolution
Main features
Isolated-type
Two-wire Transmission
Device Input Unit
4 to 20 mA, 1 to 5 V
Standard accuracy: ±0.2%
Temp coefficient: ±0.015%/°C
Resolution: 1/4,096
Conversion cycle: 100 ms/4 pts
All inputs
isolated.
±10 V, 0 to 10 V, ± 5 V, 0 to
5 V, 1 to 5 V,
±10 V DC variable range,
4 to 20 mA, 0 to 20 mA
Standard accuracy: ±0.1%
Temp coefficient: ±0.015%/°C
Resolution: 1/4,096
Conversion cycle: 100 ms/4 pts
4 inputs
All inputs
isolated.
4 to 20 mA, 0 to 20 mA, 0 to Standard accuracy: ±0.05% of full
10 V, ±10 V, 0 to 5 V, ± 5 V, scale
1 to 5 V, 0 to 1.25 V, ±1.25 V Temp coefficient: ±0.01%/°C
Effective resolution: 1/64,000
Conversion cycle:20 ms/4 pts
10 ms/2 pts
CS1W-PPS01
4 inputs
All inputs
isolated.
Max. counting speed: 20 K --pulses/s (voltage input or novoltage semi-conductor input) or
20 pulses/s
(contact input)
Isolated-type Control
Output Unit
CS1W-PMV01
4 outputs
All outputs
isolated.
4 to 20 mA, 1 to 5 V
Built-in power supply for 2wire transmission device
output scaling (±32,000),
measured value alarms
(HH, H, L, LL), rate-ofchange operation and
alarms, input disconnection alarms
Output scaling (±32,000),
measured value alarms
(HH, H, L, LL), rate-ofchange operation and
alarms, square root, input
error alarms
Output scaling, measured
value alarms (HH, H, L,
LL), rate-of-change operation and alarms, input disconnection alarms, top
hold, bottom hold, valley
hold, total value measurement
Built-in sensor power supply, contact bounce filter,
unit pulse conversion, accumulative and instantaneous value output, 4
instantaneous value
alarms.
Output disconnection
alarms, control output answerback input, output
rate-of-change limit, output high/low limits
Isolated-type Analog
Input Unit
CS1W-PDC01
4 inputs
CS1W-PDC11
Isolated-type Pulse
Input Unit
Isolated-type Power
Voltage Output Unit
CS1W-PMV02
4 outputs
All outputs
isolated
Power Transducer Input CS1W-PTR01
Unit
8 inputs
No isolation
between
inputs.
Analog Input Unit
8 inputs
No isolation
between
inputs.
CS1W-PTR02
Standard accuracy:
4 to 20 mA: ±0.1%
1 to 5 V: ±0.2%
Temp coefficient: ±0.015%/°C
4,000 (outputs)
Conversion cycle: 100 ms/4 pts
0 to 10 V, ±10 V,
Standard accuracy: ±0.1%
0 to 5 V, ±5 V, 0 to 1 V, ±1 V Temp coefficient: ±0.015%/°C
Resolution (at full scale):
±10 V or ±1 V: 1/16,000
0 to 10 V, 0 to 1 V, or ±5 V:
1/8,000
0 to 5 V: 1/4,000
Conversion cycle: 40 ms/4 pts
±1 mA, 0 to 1 mA
Standard accuracy: ±0.2%
Temp coefficient: ±0.015%/°C
Resolution: 1/4,096
Conversion cycle: 200 ms/8 pts
±100 mV, 0 to 100 mV
Standard accuracy: ±0.2%
Temp coefficient: ±0.015%/°C
Resolution: 1/4,096
Conversion cycle: 200 ms/8 pts
Output rate-of-change
limit, Output high/low limit,
Output scaling (±32,000)
Motor overdrive prevention at startup, output scaling (±32,000), measured
value alarms (H, L)
Output scaling (±32,000),
measured value alarms
(H, L)
Note: Refer to pages 299 to 301 for descriptions of the Analog I/O Units ([email protected]@, [email protected]@, CS1W-MAD44.)
306
Programmable Controllers
Programmable
Controllers
[email protected]@, [email protected]@@
Temperature Sensor Units
Direct Input from Four Temperature
Sensors
• Input directly from up to four temperature sensors
with one Unit. (The types of temperature sensor and
temperature ranges can be set separately for each
input for the [email protected]@.)
• Models available with isolated inputs to prevent
unwanted current flow between temperature sensor
inputs ([email protected]@ only).
• Provided with measured value alarms (4 points
each) ([email protected]@ only).
• Line disconnection detection provided.
Function
Circuit Configuration
Using input from thermocouples or resistance thermometers (up to 4
inputs), the Unit converts the measured temperatures into BCD or
binary data and stores them in the allocated relay area every cycle. The
data can be transferred to the DM Area or other memory locations using
the ladder program.
Temperature sensors
4 points
Specifications
Model
Classification
Unit numbers
Inputs
Input
Thermosignals
couples
Resistance
thermometers
K
J
L
R
S
T
E
B
N
W
U
PLII
±80 mV
JPt100
PT100
Ni508.4Ω
Input signal range settings
A/D conversion output data
Conversion speed
Overall
accuracy
Standard accuracy
Temperature coefficient
Cold junction
compensation error
Connections
CS1WCS1WPTS11
PTS12
CS1 Special I/O Units
0 to 95
0 to 95
4 pts
Yes
--Yes
--Yes
--Yes
--Yes
--Yes
--Yes
--Yes
--Yes
--Yes
--Yes
--Yes
----Yes
--Yes
--Yes
--Yes
4 pts set individually
4-digit binary
20 ms/4 points,
10 ms/2 points
±0.05% of Larger of
full scale
±0.05% of
full scale or
±0.1°C
±0.01%/°C
±1°C
---
CS1WPTS01
CS1WPTS02
CS1WPTS03
0 to 95
0 to 95
0 to 95
Yes
Yes
--Yes
Yes
Yes
Yes
Yes
Yes
------Yes
-------
--------------------------Yes
Yes
---
------------------------------Yes
150 ms/4 pts 100 ms/4 points
±0.1%
C200HC200HC200HTS001
TS002
TS101
C200H Special I/O Units
0 to 9
0 to 9
0 to 9
4 pts
Yes
Yes
--Yes
------Yes
------------------------------------------------------------------Yes
------------One setting for all 4 pts
4-digit BCD
4.8 s max. (when 4 pts are set for Unit)
C200HTS102
0 to 9
----------------------------Yes
---
Larger of ±0.1% or ±0.1°C ±1% + 1°C
±0.015%/°C
±1°C
---
Terminal block
Terminal block
Note: Refer to page 305 for information on [email protected]@ Process I/O Units.
Temperature Sensor Units
307
[email protected]@@
Temperature Control Units
One Unit Functions as Two Temperature
Controllers
• Supports 2-loop PID control (two degrees of freedom) or ON/OFF control.
• Input directly from two temperature sensors (thermocouples: R, S, K, J, T, E, B, N, L, or U) or platinum resistance thermometers (JPt00, Pt100).
• Open-collector, voltage, or current outputs
• Sampling period: 500 ms
• Run/start control.
• Two internal alarms per loop.
• Detects heater burnout though current detectors for
both loops.
• Record up to eight sets of target values, alarm values, and PID parameters.
• Connects to Data Setting Console.
Function
System Configuration
Perform 2-loop PID control based on inputs from thermocouples or
platinum resistance thermometers to control a transistor, voltage, or
current output. Words allocated to the Unit in memory can be manipulated from the ladder diagram to start/stop operation, set the target
value, read the process value, or perform other operations.
Two temperature
sensors
Output cable
Data Setting
Console
Manipulated variable
Specifications
General
Classification
C200H Special I/O Unit
Temperature sensor inputs
Control outputs
Thermocouples (R, S, K, J, T, E, Open-collector (pulse)
B, N, L, or U)
Voltage (pulse)
Current (linear)
Platinum resistance thermome- Open-collector (pulse)
ters (JPt00, Pt100)
Voltage (pulse)
Current (linear)
Unit numbers
0 to 9
Model
C200H-TC001
C200H-TC002
C200H-TC003
C200H-TC101
C200H-TC102
C200H-TC103
Data Setting Console
Specifications
Monitoring, setting, and changing present values, set points, alarm
values, PID parameters, bank numbers, etc.
308
Model
C200H-DSC01
Programmable Controllers
Programmable
Controllers
[email protected]@@
Heat/Cool Control Units
• Supports 2-loop PID control (two degrees of freedom) or ON/OFF control.
• Input directly from two temperature sensors (thermocouples: R, S, K, J, T, E, B, N, L, or U) or platinum resistance thermometers (JPt00, Pt100).
• Open-collector, voltage, or current outputs
• Sampling period: 500 ms
• Run/start control.
• Two internal alarms per loop.
• Detects heater burnout though current detectors for
both loops.
• Record up to eight sets of set points, alarm values,
and PID parameters.
• Connects to Data Setting Console.
Function
System Configuration
Perform 2-loop PID control (two degrees of freedom) based on inputs
from thermocouples or platinum resistance thermometers to control
heating and cooling through transistor, voltage, or current outputs.
Words allocated to the Unit in memory can be manipulated from the ladder diagram to start/stop operation, set the set point, read the process
value, or perform other operations.
Two temperature
sensors
Output cable
Data Setting
Console
Manipulated variable
MV
Heat
MV
Cool
Heat
Cool
PV
PV
Specifications
General
Classification
C200H Special I/O Unit
Temperature sensor in- Heating control output
puts
Thermocouples (R, S, K, J, Open-collector (pulse)
T, E, B, N, L, or U)
Voltage (pulse)
Current (linear)
Platinum resistance ther- Open-collector (pulse)
mometers (JPt00, Pt100) Voltage (pulse)
Current (linear)
Cooling control output
Unit numbers
Model
Open-collector (pulse)
0 to 9
C200H-TV001
C200H-TV002
C200H-TV003
C200H-TV101
C200H-TV102
C200H-TV103
Data Setting Console
Specifications
Monitoring, setting, and changing present values, set points, alarm
values, PID parameters, bank numbers, etc.
Heat/Cool Control Units
Model
C200H-DSC01
309
[email protected]@
PID Control Units
Ideal for Analog Control of Pressures, Flows,
and other Variables
• Supports 2-loop PID control (two degrees of freedom) or ON/OFF control.
• Directly input analog signal.
• Open-collector, voltage, or current outputs
• Sampling period: 100 ms
• Run/start control.
• Manual outputs supported.
• Set two internal alarms for each loop.
• Record up to eight sets of set points, alarm values,
and PID parameters.
• Digital filters can be set to dampen rapid changes in
inputs.
• Connects to Data Setting Console.
Function
System Configuration
Perform 2-loop PID control (two degrees of freedom) based on input
ranges such as 4 to 20 mA or 1 to 5 V to control transistor, voltage, or
current outputs. Words allocated to the Unit in memory can be manipulated from the ladder diagram to start/stop operation, set the set point,
read the process value, or perform other operations.
Two analog
inputs
Output cable
Data Setting
Console
Manipulated variable
Specifications
General
Classifications
C200H Special I/O Unit
Temperature sensor input
Control output
4 to 20 mA, 1 to 5 V, 0 to 5 V or 0 Open-collector (pulse)
to 10 V
Voltage (pulse)
Current (linear)
Unit numbers
0 to 9
Model
C200H-PID01
C200H-PID02
C200H-PID03
Data Setting Console
Specifications
Monitoring, setting, and changing present values, set points, alarm
values, PID parameters, bank numbers, etc.
310
Model
C200H-DSC01
Programmable Controllers
Programmable
Controllers
C200H-CP114
Cam Positioner Unit
One Unit Functions as 48 Mechanical Cams
• Supports16 external outputs and 32 internal outputs
for a total of 48 cam outputs.
• Set up to seven ON/OFF data for each cam.
• The Data Setting Console allows easy monitoring of
cam data settings, present cam angles, or etc.
• An Adjustment Operation function enables setting
cam outputs while actually operating the controlled
machine.
Function
System Configuration
Angles are detected though an externally connected resolver ([email protected]@ angle detector) and cam outputs are produced for preset ON/
OFF angle data.
C200H-CP114
Cam Positioner Unit
CS1
Cam output
Control
panel
C200H-DSC01
Data Setting
Console
Index table
Motor
Resolver
Specifications
Classification
Model
Cam Positioner Unit
C200H-CP114
No. of cam
outputs
48
(external outputs: 16,
internal outputs: 32)
Control unit
1°
Resolver response
speed
800 r/min max.
Unit
numbers
0 to 9
Resolver
response time
200 µs
(sampling frequency:
5 KHz)
Programming Devices
Name
Data Setting Console
Cam Positioner Unit
Specifications
Used to monitor, set, or change various settings such as present values,
target set values, alarm set values, PID values, and bank numbers.
Model
C200H-DSC01
311
[email protected]@@, [email protected]@@
Position Control Units
High-speed, High-precision Positioning with
1, 2, or 4 Axes
• Simple positioning systems can be created by
directly specifying operation from the CPU Unit
when required.
• Positioning data is saved in internal flash memory,
eliminating the need to maintain a backup battery.
• Use Windows-based Support Software to easily create positioning data and store data and parameters
in files. (Use WS01-NCTF1-E with [email protected]
models and WS02-NCTC1-E with [email protected]@
models.)
• Interrupt feeding, forced starting, and other features
also supported.
Function
System Configuration
These Position Control Units support open-loop control with pulse-train
outputs. Position using automatic trapezoid or S-curve acceleration and
deceleration. Models available with 1, 2, or 4 axes. Use in combination
with servomotors or stepping motors that accept pulse-train inputs.
Servo Relay
Unit
Inputs
Pulse-input Servo Driver
Servomotor
Specifications
Model
Unit name
Classification
Unit numbers
Control method
Control output signals
Controlled axes
Operating modes
Data format
Affect on scan time for end refresh
Affect on scan time for
IOWR/IORD
Startup time
Position data
No. of positions
Speed data
No. of speeds
Acceleration/
deceleration times
Acceleration/
deceleration curves
Saving data in CPU
Windows-based Support Software
312
CS1W-NC113
CS1W-NC213
CS1W-NC413
CS1W-NC133
CS1W-NC233
CS1W-NC433
Position Control Unit
CS1 Special I/O Units
0 to 95
Open-loop, automatic trapezoid acceleration/deceleration
[email protected]: Open-collector outputs
[email protected]: Line-driver outputs
1
2
4
Direct operation or memory operation
Binary (hexadecimal)
0.29 to 0.41 ms max./unit
0.6 to 0.7 ms max./instructions
2 ms min. (Refer to operation manual for conditions.)
–1,073,741,823 to +1,073,741,823 pulses
100 per axis
1 to 500 kpps (in 1-pps units)
100 per axis
0 to 250 s (time to max. speed)
C200HW-NC113
C200HW-NC213
C200HW-NC413
C200H Special I/O Units
0 to 15 (0 to F)
Open-collector
1
2
4
BCD
2.6 to 4.5 ms max./unit
2.6 to 5.5 ms max./instructions
7.51 ms min. (Refer to operation manual for conditions.)
–9,999,999 to +9,999,999 pulses
1 to 500 kpps (specified as factor)
Trapezoidal or S-curve
Flash memory
CX-Position
SYSMAC-NCT (WS01-NCTF1-E)
Programmable Controllers
Programmable
Controllers
CS1W-MC421/-MC221
Motion Control Units
High-precision, Two-axis Motion Control with
Multi-tasking G-language Programming
• High-speed control of up to 4 axes with one Unit and
up to 76 axes with one PLC (19 Units x 4 axes)
(assumes that Power Supply Unit capacity is not
exceeded).
• Winding operations easily controlled at high-speed
using traverse positioning control.
• High-speed response to commands from CPU Unit
(8 ms for 2 axes, 13 ms for 4 axes).
• Encoder response of 2 Mpps possible with 4x
frequency multiplication for applications with highspeed, high-precision servomotors.
• D interrupt code outputs to CPU Unit at end of
positioning or at specified positions (D code output
time: 3.3 ms max.).
• CX-Motion Windows-based Support Software
Define user mnemonics to use in place of G codes
to simplify MC program development and analysis.
• Servo trace function from CX-Motion to trace error
counter changes or motor speeds.
• Automatic Loading Function
MC programs and positioning data can be automatically downloaded from computer memory when
required by the MC Unit.
Function
The Motion Controller provides closed-loop control with analog outputs
for up to 2 or 4 axes, and supports the G language for advanced,
high-speed, high-precision position control, such as traverse operation.
Multi-tasking allows you to run the two axes independently for a wider
range of application.
System Configuration
Servomotor
4 axes
CPU
Unit
Analog Input
Servo Driver
Terminal Block
Conversion Unit
Teaching
Box
Note: The C200H-MC221 can also be used with CS1 PLCs.
CX-Motion
Motion Control Units
313
Specifications
General
Model
Classification
Control method
Control output signals
Internal programming language
Controlled axes
Maximum position value
Synchronous axis control
Positioning
Linear interpolation
Arc interpolation
Helical interpolation
Traverse
Infinite feed
Interrupt feed
Task programNumber of tasks
ming capacity
Number of programs
Program capacity
CS1W-MC421
CS1W-MC221
CS1 Special I/O Unit
Closed loop with automatic trapezoid or S-curve acceleration/deceleration
Analog
G language (Program started by command sent from CPU Unit’s ladder program.)
4 axes max.
2 axes max.
–39,999,999 to 39,999,999 (for minimum setting unit of 1)
4 axes max.
2 axes max.
4 axes max.
2 axes max.
2 axes max. in a plane
2-axis arc interpolation in a plane + feed axis
--2-axis traverse feeding
Infinite feeding of one or more axes
Interrupt feeding for specified axes (Positioning can be specified for when there is no interrupt.)
4 tasks max.
2 tasks max.
25 programs when using 4 tasks
50 programs when using 2 tasks
500 blocks per task when using 4 tasks
1,000 blocks per task when using 2 tasks
CX-Motion: Windows-based Support Software
Model
Supported MC Units
Applicable computer
Functions
314
[email protected]
CS1W-MC221/421, C200H-MC221, and CV500-MC221/421
DOS, OS: Windows 95/98 or Windows NT Version 4.0
Functions required for MC Unit control: Creating/editing/saving/printing system parameters, positioning data, and MC programs; monitoring MC Unit operation
Programmable Controllers
Programmable
Controllers
C200HW-MC402-E
Motion Control Unit
Advanced multi-axes Motion Control with
Multi-task BASIC language programming
• Advanced Motion control of 4 axes per unit and up
to 16 modules can be installed in one PLC
• Analogue outputs for position, Speed and Torque
control
• Hardware registration input for every axis
• Electronic CAM profiles and axes synchronization
• Friendly Motion Perfect Windows-based programming and debugging software. Provides versatile
test and monitoring functions including a 4-channel
software oscilloscope.
Function
The advanced Motion control unit provides closed-loop control of up to 4 axes, programmed in a multi-task BASIC type language and supported
by the powerful software tool. The unit provides a complete command set, allowing applications such as flying saws, rotaring knives, any synchronization and electronic CAM profile to be easily programmed.
System Configuration
Motion Perfect
C200HW-MC402
Termnal Block
Conversion Unit
Analog Input
Servo Driver
Servomotor
4 Axes
I/O
Motion Control Unit
315
Specifications
General
Model
Classification
Control Method
Control Output signals
Programming language
Controlled axes
Measurement units
Positioning
Task programming capacity
Linear interpolation
Arc interpolation
Helical interpolation
Axes Synchronization
Axes Linked CAM profile
Hardware Registration Interrupt
Number of tasks
Number of programs
Data storage capacity
C200HW-MC402-E
C200H Special I/O Unit
Closed loop Position, Speed and Torque control
Analogue
BASIC type motion control language
4 real axes and 4 virutal axes
User definable
4 axes
For any 2 axes
For any 3 axes
For any 2 axes
For any 2 axes
4 axes
Up 5 tasks simultaneous plus interface task
14
251 (VR) + 16000 (Table) max.
Motion Perfect Software
Model
Supported MC Units
Applicable computer
Functions
316
Motion Perfect
C200HW-MC402-E, R88A-MCW151-E,
R88A-MCW151-DRT-E
Windows 95/98/2000/NT4.0
Programming and debugging software
tool. Test and moitoring functions
including a 4-channel software oscilloscope.
Programmable Controllers
Programmable
Controllers
CS1W-MCH71
Motion Control Unit
Multi-axes Motion Control over high-speed
MECHATROLINK-II
•
•
•
•
•
Up to 30 axes controlled with less wiring
Supports Position, speed and Torque control
Electronic CAM profiles and axes synchronization
Hardware registration input for every axis
Program control commands, like Multi-task
programming and branching commands, and
various arithmetic operations for maximum
program efficiency
• Access to the complete system from one point
Function
Multi-axes control is made easy by freely combining control axes. Up to
32 axes can be used, including 30 physical axes and two virtual axes,
and each axis can be set individually. Position Control, synchronized
control (electronic gear, electronic Cam, follow-up), speed control, and
torque control are all supported, enabling a wide range of applications.
By using high-speed servo communications, motion programs, system
parameters, system data, and servo drive parameters can be set and
read from the software tool.
System Configuration
CS-series
Programmable Controller
Support Software
(MC-Miel for MCH,
free software)
CS1W-MCH71
motion control unit
MECHATROLINK-II
Sigma II
or W-series
servo drive
30 nodes max.;
total length: 50 m
JUSP-NS115
MECHATROLINK-II
Interface Unit
Limit switches,
contact sensors
Motion Control Unit
JEPMC-W6022
Terminating Resistor
317
Ordering Information
Motion Controller
Name
Motion Control Unit
Support Software
Model
CS1W-MCH71
MC-Miel (free of charge)
Mechatrolink-II related devices
Name
Mechatrolink-II Interface Unit
Mechatrolink-II Terminator
Mechatrolink-II Cables
24V DC I/O Module
Counter Module
Pulse Output Module
Model
JUSP-NS115
JEPMC-W6022
JEPMC-W6003-A5
JEPMC-W6003-01
JEPMC-W6003-03
JEPMC-W6003-05
JEPMC-W6003-10
JEPMC-W6003-20
JEPMC-W6003-30
JEPMC-IO2310
JEPMC-PL2900
JEPMC-PL2910
Remarks
For Sigma-II and W-series Servo drives
Terminating resistor
0.5 meter
1 meter
3 meters
5 meters
10 meters
20 meters
30 meters
64 Inputs, 64 Outputs
Reversible counters, 2 channels
Pulse train positioning, 2 channels
Specifications
General
Model
Classification
Applicable PLCs
Control Method
Controlled devices
Programming language
Controlled axes
Control functions Positioning (PTP)
Motion
programs
318
CS1W-MCH71
CS-series CPU Bus unit
CS-series, new version (CS1[]-CPU[][]H)
MECHATROLINK-II (Position, Speed and Torque control )
Sigma-II and W-series Servo Drives (ver. 38 or later) with MECHATROLINK-II Interface and various I/O Units.
BASIC type motion control language
32 max, including 30 physical or virtual axes and 2 virtual axes
Executes positioning independently for each axis at a specified speed or the speed system parameter.
(Simultaneous specification: Up to eight axes/block, Simultaneous execution: Up to 32 blocks/Unit)
Linear interpolation
Executes linear interpolation for up to eight axes at a time at the specified interpolation feed speed.
(Simultaneous specification: Up to eight axes/block, Simultaneous execution: Up to 32 blocks/system)
Circular interpolation
Executes circular interpolation for two axes in either clockwise or counterclockwise at the specified interpolation
feed speed. Helical circular interpolation is also possible with single-axis linear interpolation added.
(Simultaneous specification: Two or three axes/block, Simultaneous execution: Up to 16 blocks/system)
Other functions
Origin searches, interrupt feeding, timed positioning, traverse positioning, independent electronic cam, synchronized
electronic cam, link operation, electronic gear, follow-up synchronization, speed reference, torque reference
Number of tasks, number Up to 8 tasks and 256 programs/Unit (8 parallel branches per task max.)
of programs
Program capacity
In motion program conversion, 8,000 blocks/Unit max. (2 Mbytes); number of blocks: 800
Data capacity
Position data: 10,240 points/Unit; Cam data: 32 max.; 16,000 points/Unit
Subroutine nesting
Five levels max.
Programmable Controllers
Programmable
Controllers
[email protected], C200H-CT021
High-speed Counter Units
Two- and four-channel high-speed counter
units with built-in fast control I/O
• Max. input frequency = 500 kHz. (when line driver
input is used)
• Output turns ON less than 0.5 ms after set value
is reached. (may deviate during execution of IORD/
IOWR instructions)
• 32-bit counting range.
• 2- and 4-axis operation available.
• Digital variable noise filter provided.
• 5-, 12-, and 24-V line driver inputs available. (5- and
12-V line driver input is only available, however, for
1 axis with the CS1W-CT021 and 2 axes with the
CS1W-CT041.)
• Supports simple, ring, and linear counting modes.
• Supports offset phase input, up and down pulse
input, and pulse+direction input.
• Supports 4 external control inputs, and a total of 16
functions can be set including open gate, close gate,
preset, reset, capture, stop/capture/reset combinations, and reset enable.
• One Unit supports 4 external outputs and 28 internal
outputs with counter value zone comparisons, target
comparisons, delays, holds, programmable outputs,
and hysteresis settings.
• Pulse rate measurement function and data logging.
• Counter outputs and external control inputs can be
used to trigger interrupt tasks in the CPU Unit.
• Settings can be changed during Unit operation.
Function
The High-speed Counter Units count pulse signal inputs that are too
fast to be detected by normal Input Units. The Units can be programmed to produce outputs according to counter values for specified conditions, and many other functions are supported.
System Configuration
Counter inputs
Encoder
High-speed Counter Units
319
Specifications
General
Classification
Number of
counters
C200H Special I/O Unit 2
CS1 Special I/O Unit
2
4
320
Encoder A and B input,
pulse input, Z signal
Open-collector
Input voltage: 12 V DC or 24 V DC
RS-422 line driver
Open-collector
Input voltage: 5 V DC, 12 V DC, or 24
V DC
(5- and 12- V DC input only possible
for 1 axis.)
RS-422 line driver
Open-collector
Input voltage: 5 V DC, 12 V DC, or 24
V DC
(5- and 12- V DC input only possible
up to 2 axes.)
RS-422 line driver
Maximum counting
speed
50 kcps
75 kcps
50 kcps
500 kcps
50 kcps
Unit numbers
Model
0 to F
C200H-CT021
0 to 92 (4 unit numbers CS1W-CT021
per Unit)
CS1W-CT041
500 kcps
Programmable Controllers
Programmable
Controllers
CS1W-CTS21
SSI Encoder Input Unit
SSI (synchronous serial interface) is a
standard communication protocol developed
for absolute encoders. It provides easier
connection and reduced wiring compared to
parallel connection.
Specifications
SSI Communication
Item
CLK lines
DATA lines
Number of data-bits
Value coding
Clock frequency
Monoflop time
Sample rate
Input Specifications
Specification
Non-isolated differential line driver,
RS422 compliant
Electrically isolated differential line
receiver, RS422 compliant
9 to 31 (default: 24)
Gray/Binary/Tannenbaum/Raw
(default Gray)
100kHz to 1.5MHz
10µs to 99,990µs (default: 40 µs)
About 2500 Samples/sec with
2 encoders connected
(with default settings)
Item
Input Voltage
Input Current (typical)
ON Voltage (min.)
OFF Voltage (max.)
Max. repetition rate
Min. pulse width
Input Voltage
Digital Inputs
24 V DC (19.6 V to 26.4 V)
7.6 mA
19.6 V
4V
1 kHz
10 µs
24 V DC (19.6V to 26.4V)
24V
B5/B6
0V
2 k9
1 k9
6809
A5/A6
SSI Encoder Input Unit
321
Output Specifications
Item
Driver Type
Operating Voltage Range
Maximum Switching Capacity
Minimum Switching Current
Output ON-delay
Output OFF-delay
Leakage Current
Connector (CN1 and CN2) Pin-layout
Specification
Open Collector (NPN/PNP selectable)
12-24 V (10.2 to 26.4 V)
46 mA at 10.2 V to 100 mA at 20.4 V
to 26.4 V (400mA max./common)
(linear behaviour)
5 mA
0.1ms max.
0.1ms max.
0.1mA max.
The power supplied to the Unit, to feed the Digital Outputs, has to be
supplied externally and should be a double insulated class II (overvoltage) type with ratings from 12 to 24VDC (10.2 to 26.4VDC). Characteristics of the Power Supply Input circuitry are summarised in the
following table.
Item
Operating Voltage Range
Current Consumption
Internal Fault Protection
Reverse Polarity Protection
Specification
10.2-26.4 V DC
25 mA max. (excl. load current)
Two 1 A (not replaceable) fuses
in Power Supply lines
Yes
The Digital Outputs are insulated from the I/O-bus but not from each
other. They are not short circuit protected.
Use the following table to make connections directly to the soldering
terminals of the connector jack(s) (see Nomenclature section for position of connectors 1 and 2 and rows A and B):
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
Connector 2 (CN2)
Row A
Row B
B1
0V_PS¹
24V_PS2
O2 NPN
O2 PNP
B2
O3 NPN
O3 PNP
B3
B4
0V I2
24V I2
B5
0V I3
24V I3
B6
B7
0V ENC2_PS3 + ENC2_PS4 B8
B9
DATA2 DATA2 +
B10
B11
CLOCK2 CLOCK2 +
B12
B13
B14
B15
B16
B17
B18
B19
0V ENC_PS3 + ENC_PS4 B20
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
Connector 1 (CN1)
Row A
Row B
0V_PS¹
24V_PS2
B1
O0 NPN
O0 PNP
B2
O1 NPN
O1 PNP
B3
B4
0V I0
24V I0
B5
0V I1
24V I1
B6
B7
0V ENC1_PS3 + ENC1_PS4 B8
B9
DATA1 DATA1 +
B10
B11
CLOCK1 CLOCK1 +
B12
B13
B14
B15
B16
B17
B18
B19
0V ENC_PS3 + ENC_PS4 B20
Digital Output Circuitry:
322
Programmable Controllers
Programmable
Controllers
[email protected]@@/-HIO01
Customizable Counter Units
Dedicated PLC unit for position control.
• Fast loop control with all the flexibility and
functionality of a PLC.
• Position control using Analog or pulse train
output.
• Standard encoder interface inputs.
• Programmed using standard PLC Ladder
language and CX-Programmer software.
Function
System Configuration
The customizable counter units provide a highly flexible solution for fast
loop control. The PLC functionality together with the high-speed allows
the units to be used in a wide range of general purpose applications
including closed-loop position control.
Customizable
Counter Unit
Counter input
Encoder
SYSMAC CS1
Analog output
Motor
Inverter
Specifications
General
Model number
Type
Inputs
Outputs
CS1W-HCP22-V1
Counter inputs, pulse outputs
12 DC inputs
Counter inputs
1 analog input
8 transistor
outputs
2 pulse outputs
2 analog outputs
CS1W-HCA22-V1
Counter inputs, pulse outputs
CS1W-HIO01-V1
Basic type
Yes
Yes (2 inputs)
No
Yes
CS1W-HCA12-V1
Analog inputs, counter inputs,
analog outputs
Yes
Yes (1 input)
Yes
Yes
Yes
Yes (2 inputs)
No
Yes
Yes
No
No
Yes
Yes
No
No
Yes
No
Yes
No
No
Programming Functions
Programming language
Basic instruction execution speed
Program capacity
Data memory capacity
Backup functions
CS1 CPU Unit data exchange
Programming Device
Programming Device Connecting Cable
Customizable Counter Units
Ladder programming
200 ns (1 Kword) or 400 ns (4 kWords), switchable
1 Kword or 4 kWords, switchable
6 kWords + 2 kWords of expanded data memory
10-day capacitor backup and flash memory storage
132-channel data link (maximum)
CX-Programmer (versions 1.2. or later) or Programming Console
CS1 Connecting Cable or Programming Console Cable
323
Counter Inputs (CS1W-HCP22/HCA22)
Operating modes
Signal level
Input method
Counting speed
Other functions
Linear and ring
5, 12, or 24 V, or line driver (only one input each for 5 and 12 V)
Phase difference (×1, ×2, or ×4), up/down, or pulse with direction
Voltage: 50 kcps
Line driver: 50/200 kcps
Compatible with absolute encoder Servo Driver s (such as the OMRON W Series).
Virtual axis function
Pulse Outputs (CS1W-HCP22)
Output signal
Signal level
Output speed
Clockwise/counterclockwise
5 to 24 V
200 kpps
Analog Outputs (CS1W-HCA12/HCA22)
Output signal
Resolution
Accuracy
Conversion speed
324
–10 to 10 V, 0 to 10 V, 1 to 5 V, 0 to 5 V
1/4,000, 1/10,000 (for –10 to 10 V only)
±0.3% of FS (23±2°C), ±0.5% of FS (0 to 55 °C)
0.5 ms max.
Programmable Controllers
Programmable
Controllers
[email protected]@@/C200H-IDS01-V1
RFID Sensor Unit
Easy integration of RFID Systems into PLC's.
• Connects V600 RFID read/write heads directly to
the PLC.
• Function checking possible with standard hand-held
Programming Console.
• Read data from Data Carriers simply by sending
a read command.
• The C200H-IDS01-V1 can read/write up to 1,024
bytes. The CS1W-V600C11/12 can read/write up to
2,048 bytes.
Function
Read/write data in Data Carrier memory by sending read/write commands from the CPU Unit to the Read/Write Head.
One Read/Write Head can be connected to the CS1W-V600C11 and
two Read/Write Heads can be connected to the CS1W-V600C12. The
data transfer speed has been increased in both models.
System Configuration
Read/
Write Head
Data Carrier
Specifications
Classification
Connectable ID System
CS1 CPU Bus Unit
V600 Series (electromagnetic,
for short distances)
C200H Special I/O Unit
RFID Sensor Unit
Connectable Read/
Write Heads
1 Read/Write Head
2 Read/Write Heads
---
External power supply Unit numbers
Model
Not required
24 V DC
Not required
CS1W-V600C11
CS1W-V600C12
C200H-IDS01-V1
0 to 95
0 to 94
0 to 9
325
Serial Communication Units
Serial Communications Features
Unit
Model
Ports
Serial communications mode
Protocol
Host Link
NT Links
macros
Generalpurpose
external
devices
CPU Units
All models Port 1: Peripheral
No
Port 2: RS-232C
No
ASCII Units C200HPort 1: RS-232C
No
ASC02
Port 2: RS-232C
No
C200HPort 1: RS-232C
No
ASC11
Port 2: RS-232C
No
C200HPort 1: RS-232C
No
ASC21
Port 2: RS-422A/485 No
C200HPort 1: RS-232C
No
ASC31
Port 2: RS-232C
No
Serial Com- CS1WPort 1: RS-232C
Yes
munications SCB21-V1 Port 2: RS-232C
Yes
Boards/Units CS1WPort 1: RS-232C
Yes
SCB41-V1 Port 2: RS-422A/485 Yes
CS1WPort 1: RS-232C
Yes
SCU21-V1 Port 2: RS-232C
Yes
DeviceNet
DRT1Port 1: RS-232C
No
RS-232C
232C2
Port 2: RS-232C
Unit
326
Host
computers
OMRON
PTs
Yes
Yes
No
No
No
No
No
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
No
No
No
No
No
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
No
No-protocol Peripheral
bus
Generalpurpose
external
devices
No
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Programming
Devices
Programming
Console bus
Programming
Console
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
BASIC
programming
Message
communications
Generalpurpose
external
device
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
Programmable Controllers
Programmable
Controllers
[email protected]@
ASCII Units
Easily Perform Serial Data Communications
• Perform ASCII communications with a wide range of
external devices.
• The C200H-ASC11/ASC21/ASC31 function as special processing units with BASIC programming.
• Large-capacity user memory: 200 Kbytes
• Model available with RS422A/485 port.
• Various forms of data exchanges with CPU Unit:
Select the best method for the read/write trigger and
timing.
• High-speed data exchanges possible with shared
memory (not dependant on I/O refresh).
• A wide range of interrupt processes: Interrupts from
CPU to ASCII Unit, communications interrupt, key
interrupts, timer interrupts, error interrupts, etc.
• Easy control of transmission control signals.
• Calculation instructions for error check codes.
• Many BASIC debugging functions (break points,
1-step execution, execution stop monitoring, etc.)
• Error log supported with up to 30 error records.
Function
System Configuration
The ASCII Units support BASIC language programming and RS-232C
and RS422A/485 serial communications. BASIC programming enables
ASCII communications with essential any external device. It can also
be used as a special processing unit to aid the CPU Unit without using
external communications.
The C200H-ASC11/ASC21/ASC31 provide shared memory with the
CPU Unit, and both the ASCII Unit and the CPU Unit can access the
shared memory asynchronously, providing for high-speed data
exchanges between the two Units without using interrupts.
A library interface toolkit is available for the creation of user-defined
library routines in BASIC or C.
Terminal
(e.g., Windows
Hyperterminal)
BASIC
program
RS-232C
RS-232C
General-purpose
external device
Specifications
General
Classification
User memory
C200H Special I/O Unit 200 Kbytes
Shared memory
Provided
(90 words in I/O memory)
Serial communicaUnit numbers
tions ports
RS-232C x 2
0 to F
RS-232C x 1, RS-422A/
485 x 1
RS-232C x 2, RS-232C
x 1 for terminal
Model
C200H-ASC11
C200H-ASC21
C200H-ASC31
Note: The C200H-ASC02 can also be used with CS1 PLCs.
ASCII Units
327
CS1W-SCU21-V1/[email protected]
Serial Communications Units/Boards
Supports Protocol Macros, Host Link
Communications, and 1:N NT Links
• Serial Communications Board
• Increase the number of serial ports without using
I/O slots.
• Connect general-purpose external devices 1:N
using RS-422A/485.
• Generate interrupts to the CPU Unit when data is
received.
• Serial Communications Unit
• Mount up to 16 Units (including all other CPU
Bus Units) on CPU or Expansion Racks. Ideal for
systems that require many serial ports.
Function
System Configuration
Either an Inner Board or CPU Bus Unit can be used to increase the
number of serial ports (RS-232C or RS-422A/485) two at a time. You
can specify Protocol Macros, Host Link Communications, or 1:N NT
Links separately for each port. With the CS1 Series, you can always
install the right number of serial ports for your system.
Host computer
Programming
Device
Serial
Communications
Board
PT
Serial
Communications
Unit
Machine
Machine
Device
Microcomputer or
other device
Device
Non-OMRON PLC
Specifications
General
Unit
Classification
Serial Communications
Board
Inner Board
Serial Communications
Unit
CS1 CPU Bus Unit
328
Serial communications
modes
Set separately for each
port:
Protocol Macro, Host Link,
or 1:N NT Link
Serial
Unit numbers
RS-232C x 2
--RS-232C x 1, RS-422A/485
x1
RS-232C x 2
0 to F
Model
CS1W-SCB21-V1
CS1W-SCB41-V1
CS1W-SCU21-V1
Programmable Controllers
Programmable
Controllers
Protocol Macros
Easily Create Protocols for Data Exchange with External Devices; Execute with One Instruction
Function
System Configuration
Protocols for communications with external devices can be easily created according to the communications standards required by the external device. Protocol macros enable communications with essentially
any external device with an RS-232C or RS-422A/485 port without programming communications in the PLC.
Standard system protocols are provided as a standard feature for communications with OMRON components, such as Temperature Controllers, Panel Meters, Bar Code Readers, and Modems. A Windowsbased tool called CX-Protocol is also available to enable creation of
protocols for most any external device.
Standard system protocols
(provided in Unit or Board)
OMRON
component
CD-ROM
CX-Protocol
User-created protocols
Create and
transfer
protocols
General-purpose
external device
Types of Protocol
Protocols
Standard system protocols
User-created protocols
External devices
OMRON components
General-purpose external device
Required products
Serial Communications Board or Unit
Serial Communications Board or Unit + CX-Protocol (Windows-based protocol support
software)
Standard System Protocols
Component
CompoWay/F-compatible components
Model
OMRON CompoWay/F slave
components
Digital Controllers and Small Digital Controller with Communications (53 x 53 mm)
E5CK
Temperature Control- Temperature Controllers with Digital Indications (Thermac J with com- [email protected]
lers
munications) (96 x 96 mm or 48 x 96 mm)
Digital Controllers with Communications (96 x 96 mm)
[email protected]
High-density Temperature Controller with communications (8 control E5ZE
points)
Intelligent Signal Processors (special specifications)
[email protected]
Bar Code Readers
Laser Scanner type
CCD type
Laser Micrometer
V500
V520
3Z4L
Visual Inspection Sys- High speed, high precision, low cost
tems
High-precision inspection/positioning
Character inspection software/positioning software
F200
F300
F350
RFID Controllers
V600
V620
---
Electromagnetic coupling (for short distances)
Microwave (for long distances)
Hayes Modem AT Command
Serial Communications Units/Boards
Send/receive sequences
CompoWay/F command send/response
receive
Present value read, set point read, manipulated variable read, etc.
Set point write, alarm write, PID parameter write, etc.
Display value read, comparison value
read, write, etc.
Read start, data read, read stop, etc.
Measurement condition set, continuous
measurement start, etc.
Measurement, continuous measurement, etc.
Measurement, positioning, inspection,
character inspection, etc.
Carrier data read, autoread, write, etc.
Modem initialize, dial, send, etc.
329
NT-AL001
RS-232C/RS-422A Adapter Unit
Allows integration of RS232C devices into
RS-422A networks.
• Long-distance transmissions are possible through
an RS-422A interface. By converting from RS-232C
to RS-422A and then back to RS-232C, a transmission distance of up to 500 m can be achieved.
• No power supply is required. If the 5-V terminal
(150 mA max.) is connected from the RS-232C
device, a separate power supply is not required
to drive the Adapter Unit.
• The removable terminal block enables wiring not
possible with D-sub connectors. (The RS-232C
interface is 9-pin D-sub.)
Specifications
RS-232C Interface
Item
Baud rate
Transmission distance
Connector
Specification
64 Kbps max.
2 m max.
9-pin, D-sub connector (female)
RS-422A Interface
Item
Baud rate
Transmission distance
Terminal block
330
Specification
64 Kbps max. (depends on RS-232C baud rate)
500 m max.
8 terminals, M3.0; detachable
Programmable Controllers
Programmable
Controllers
CS1W-GPI01
GP-IB Interface Unit
• Enables communications between SYSMAC
CS-series PLCs and GP-IB instruments.
• Conforms to the standard interface IEEE-488-1978
(GP-IB).
• Usable in either Master Mode (controller) or Slave
Mode (talker, listener).
• Communications with GP-IB instruments are easily
implimented simply by using the INTELLIGENT I/O
READ and INTELLIGENT I/O WRITE (IORD/IOWR)
instruction in the ladder program in the CPU Unit to
read and write buffer memory in the GP-IB Interface
Unit.
Specifications
Item
Name
Model number
Unit type
Mounting location
Max. number of GP-IB Interface Units
Unit number setting range
GP-IB Interface Unit settings when editing the I/O tables offline
with the CX-Programmer
Transmission method
Communications method
Interface
Handshaking method
Functional specifications
(GP-IB interface functions)
Connection configurations
Transmission distance
Max. number of connected devices
GP-IB device address
Delimiters
Max. data transfer size
Max. number of connectors
Current consumption
Dimensions
Weight
GP-IB Interface Unit
Specification
SYSMAC CS-series GP-IB Interface Unit
CS1W-GPI01
CS1 Special I/O Unit
CS1 CPU Rack or CS1 Expansion Rack
Up to 4 GP-IB Interface Units per CPU Unit
0 to 95
Number of unit numbers used: 1
Number of input words allocated: 5
Number of output words allocated: 5
8-bit parallel data transfer
Half duplex
Conforms to IEEE-488-1978 (24-pin) standards
Three-line handshaking
Master mode: SH1, AH1, T6, TE0, L4, LE0, C1 to C4, and C28
Slave mode: SH1, AH1, T6, TE0, L4, LE0, SR1, RL0, PP0, DC1, and DT0
Star configuration or daisy-chain configuration
Limits on the length of cables in the system
(All three of these conditions must be satisfied simultaneously.)
Total cable length ≤ Number of devices in the system × 2 m
Total cable length ≤ 20 m
Length of a single cable ≤ 4 m (for a 1:1 connection)
15 devices max. including the GP-IB Interface Unit
0 to 30
Select from the following: CR + LF, CR, LF, EOI, or user-set code.
512 bytes max. in a single reception or transmission
2 (connectors can be stacked)
5 VDC, 330 mA
35 × 130 × 101 mm (W × H × D)
258 g max.
331
Communications Networks
Overview
Level
Information networks
Network
Ethernet
Controller Link
Control
networks
Controller Link
Functions
Host computer to PLC
PLC to PLC
Host computer to CPU Unit memory
card
UNIX computer or other socket service to PLC
Computers connected directly to
network and PLC
PLC to PLC
PC Link
DeviceNet
DeviceNet
PLC to components (slaves)
PROFIBUS-DP
PLC to components (slaves)
CAN/CANopen
Component to components
CompoBus/S
PLC to components (slaves)
Communications
FINS messages
Unit/Board
Ethernet Unit
FTP server
Socket services
FINS messages
Data links (offsets and automatic setting)
FINS messages
Data links (offsets and automatic setting)
Simple data links
FINS messages on open network
Controller Link Support
Board and Unit
Controller Link Unit
High-capacity remote I/O on open network
(fixed or user allocations)
High-capacity remote I/O on open network
(user allocations)
Freely configurable, object-oriented communication
using CANopen or user-defined CAN protocols
High-speed remote I/O with OMRON network
(fixed allocations)
PC Link Unit
DeviceNet Master Unit
and Configurator
DeviceNet Master Unit
and Configurator
PROFIBUS-DP Master,
I/O Unit and Configurator
CANopen Unit
CompoBus/S Master Unit
Specifications
Communications
Network
Messages
Ethernet
Yes
Controller Link
Yes
PROFIBUS-DP
Limited to DPV1
devices
Manually configurable
Yes
12 Mbps
Comm cycle from 1 ms
DeviceNet
Yes
CANopen
Yes
CompoBus/S
---
Data links
Remote I/O
Maximum speed
----10/100 Mbps
Total distance
---
Maximum nodes
Communications
media
-----
Yes
--2 Mbps
Comm cycle:
Approx. 34 ms
(Wired: 32 nodes, 2Kbits + 2-Kword data
links)
Twisted-pairs:1 km (at 1200 m up to
500 bps)
93.75 kbps,
Optical: 20 km
100 m at 12 Mbps.
Extension by optical
links is possible.
32/62 with repeaters 126 with repeaters
Special twisted-pair
PROFIBUS cable
cable or optical cable
--Yes
500 Kbps
Comm cycle:
Approx. 5 ms
(128 inputs and
128 outputs)
Yes
Yes
1 Mbps
(acyclic, on-event
communication)
--Yes
750 Kbps (See note 1.)
Comm cycle:
Approx. 1 ms
(128 inputs and
128 outputs)
500 m
(at 125 kbps)
5 km at 10 kbps to 40 Trunk line: 500 m
m at 1 Mbps
(See note 2.)
Communications cycle: 6 ms max.
63
DeviceNet cable
127
ISO11898. e.g.
DeviceNet cable
Network data link capacity
Remote I/O
capacity
---
32,000/62,000 words
---
---
---
---
---
300 words (C200H)
7000 words
(CJ1, CS1)
32,000 pts
(with Configurator)
2,048 pts
(without Configurator)
CS1, CJ1,
CVM1, CV Series,
C200HX/HG/HE,
C200HS, CQM1/
CQM1H (with I/O
Link), CPM2C (with I/O
Link)
Up to 200 words
configurable
256 pts
Supporting PLCs
CS1, CJ1, CVM1, CV CS1, CJ1,
Series,
CVM1, CV Series,
C200HX/HG/HE
C200HX/HG/HE
CS1,
C200HX/HG/HE
CS1, CJ1, C200HX/
HG/HE, C200HS,
CQM1/CQM1H,
[email protected]
(-DRT) SRM1;
CPM1A/CPM2C
(with I/O Link)
CS1, CJ1,
C200HX/HG/HE/HS,
CQM1/CQM1H
(I/O link),
CPM1A (I/O link)
32
2-core or 4-core
VCTF cable, special
flat cable (See note 3.)
---
Note: 1. For high-speed communications mode. Trunk line length is 100 m (30 m max. for 4-core VCTF or special flat cable).
2. For long-distance communications mode (200 m max. for 4-core VCTF or special flat cable).
3. Different types of cables cannot be mixed.
332
Programmable Controllers
Programmable
Controllers
[email protected]@
Ethernet Units
Enables fast data transfer within Factory
Automation systems, and easily links FA
systems to plant management systems
• Access socket services simply by manipulating
specific bits in memory.
• Take advantage of data transfer by e-mail.
• Seamless communication with Controller Link
and other networks.
• Use the Ethernet standard protocols, TCP/IP and
UDP/IP.
• Use OMRON’s standard FINS message
communications.
• Exchange files with host computers using FTP.
• Set communications parameters with the
CX-Programmer setup menus.
Function
Features of the 100Base-TX Model
• While the 100Base-TX model maintains backward compatibility with
the earlier models (10Base-5 and 10Base-T), the new model has a
basic system repsonse performance about 4 times faster.
• The FINS message communications capabilities have been
improved dramatically.
• Increased number of nodes (from 124 to 254 nodes)
Achieve a wide range of communications from PLCs connected to an
Ethernet network: Transfer data with TCP/IP or UDP/IP socket services, executed OMRON’s standard FINS commands, transfer files
with FTP, or send mail with SMTP. Select the communications services
that are required and flexibly connect PLCs on an information level
Ethernet network.
• Supports TCP/IP protocol as well as the earlier UDP/IP protocol.
• The host computer’s IP address can be set dynamically (DHCP).
System Configuration
• A mail receiving function has been added (POP3).
• A function has been added that automatically corrects the PLC’s
internal clock (SNTP) .
• Various kinds of servers can be specified by their host name (DNS).
Ethernet network
Ethernet Unit
Ethernet Unit
Specifications
Classification
CS1 CPU Bus Unit
Ethernet Units
Communications services
FINS communications, FTP server, socket services, and mail
services
Unit numbers
Connector
0 to F max. 4 Units per CPU 10Base-5
10Base-T
100Base-TX
In addition to the services listed above, the CS1W-ETN21 supports
FINS communications through TCP/IP, auto-correction of the
(10Base-T)
PLC’s internal clock, and host name identification of various kinds
of servers.
Model
CS1W-ETN01
CS1W-ETN11
CS1W-ETN21
333
[email protected]@-V1, [email protected]@-V1
Controller Link Units and Controller Link Support
Board
OMRON’s efficient and easy-to-use
FA Network
• Achieve high-capacity, flexible data links.
• Transfer large volumes of data through a message
service.
• Connect through twisted-pair cables or optical fiber
cables.
• Connect CS1, CJ1, C200HX/HG/HE and CQM1H
PLCs.
• Complete error correction and troubleshooting
functions.
• Quick configuration of communication links with
CX-Programmer's setup menus.
• Increase network reliability with duplex
connections for optical networks.
• Use either ring mode or bus mode for optical networks.
Function
Controller Link is OMRON’s proprietary FA-level network. It supports
automatic data links between PLCs and between PLCs and host computer, as well as programmed data transfers using a message service.
You get high-capacity, flexible data links and high-capacity data transfers with messages. For a low-cost communications system, twistedpair cables can be used.
System Configuration
Message Communications
Data Links
Controller
Link Unit
Controller
Link Unit
PLC
PLC
PLC
PLC
PLC
PLC
CS1
Programmed data transfers (when needed)
Communications instructions in
user program
Cyclic transfer with shared memory data areas
I/O bits, LR Area bits, DM Area words, etc.
Specifications
General
Unit/Board
Controller Link Units
Controller Link Support
Boards
334
Classification
CS1 Bus Unit
Personal computer
board
Communications
Data links and message
communications
Media
Wired
Optical
(H-PCF
cable)
Optical
(GI fiber
62.5/125 µm)
Wired
Optical
(H-PCF
cable)
Optical
(GI fiber
62.5/125 µm)
Specifications Unit numbers
Up to 4 Units
0 to F (4 Unit max.)
can be mounted
to CPU Rack or
CS1 Expansion
Racks.
Model
CS1W-CLK21-V1
CS1W-CLK12-V1
Applicable com- --puter: Windowscompatible
computer with
PCI bus
3G8F7-CLK21-V1
3G8F7-CLK12-V1
CS1W-CLK52-V1
3G8F7-CLK52-V1
Programmable Controllers
Programmable
Controllers
CS1W-PRM21
PROFIBUS-DP Master Unit
• PROFIBUS-DP master class one with support
of DP-V1 data types.
• 7 kWord I/O
• Simple configuration through FDT/DTM
based configurator
• Special CPU unit
• Handles data independent of the CPU unit,
thus reducing CPU load
Function
The CS1W-PRM21 is a master system (DPM1). It exchanges I/O data
and communication/status information with the CPU of the PLC. To
configure the CS1W-PRM21 a serial port of the CPU can be used. But
because configuring is done through FINS
communication virtual any accesspoint on the PLC network can be
used. It exchanges data and commands with PROFIBUS-DP slave
stations over the PROFIBUS network.
Specifications
Model
CS1W-PRM21
Remarks
Main function
Unit No.
Maximum number of units mountable per
PLC
Configurator
Supported baud rate(s)
Selectable PROFIBUS address
Maximum number of PROFIBUS slaves
Maximum number of I/O points
Maximum number of I/O points per
PROFIBUS slave
Control and status ares size
Supported Global_Control services
Supported Master-Slave communication
services
Power consumption
Dimensions
Weight
Ambient temperature
PROFIBUS-DP Master Unit
Basic PROFIBUS-DP master Class 1
functions plus: DPV1 data types support
0-15
16
FTD/DTM based
All baud rates as specified by the standard
EN50170 Volume 2, the PROFIBUS extensions to EN50170, as well as the standard
IEC61158:
9.6 kBit/s,
19.2 kBit/s,
45.45 kBit/s.
93.75 kBit/s,
187.5 kBit/s,
500 kBit/s,
1.5 MBit/s,
3 MBit/s,
6 MBit/s,
12 MBit/s
0-125
125
7168 words
244 bytes In / 244 bytes Out
25 words
Sync
Unsync
Freeze
Unfreeze
Clear
Data_Exchange
Slave_Diag
Set_PRM
Chk_Cfg
Global_Control
400 mA at 5 V
34.5 mm wide x 130 mm height x
111.2 mm depth
154 gr
Operating: 0 °C to 50 °C
Special CPU unit
Maximum depends on PLC CPU-type
Incorporates a Generic DTM to use with GSD-file
based slaves
The baud rate value to be used must be selected
through the Configurator.
Set through the configurator
Through Control Area
335
C200HW-PRM21
PROFIBUS-DP Master Unit
PROFIBUS-DP master for C200HX, C200HG,
C200HE, C200HS and CS1
• The C200HW-PRM21 is the PROFIBUS-DP master
unit for OMRON’s CS1 and C200H-series.
• Multiple PROFIBUS-DP masters can be mounted in
the same PLC system.
• Switch to activate bus termination
• Supports up to 124 slaves.
• Allows mapping of slave data to any PLC data area.
• Default mode requires no PLC settings.
Ordering Information
Product Code
C200HW-PRM21
W349-E2-02
WS02-PDC2-E
Description
PROFIBUS master unit for C200Hα and CS1 PLCs
User Manual for PROFIBUS unit + configurator
Configurator Software
Specifications
Communication Specification
Applicable standard
Network topology
Bus connector
Bus termination
Baud rates
Communication distance
Communication cable
Fieldbus cycle time
Supported DP functions
as responder
as requester
EN 50170 vol.2
Line, max. 125 node addresses
9-pin sub-D female
Built in, switch selectable
9.6k, 19.2k, 93.75k, 187.5k, 500k, 1.5M, 3M, 6M, 12M bits/s, set by configurator
(default 1.5M).
100 m (at 12 Mbit/s) to 1200 m (at 9.6 kbit/s) per segment. Extendible to 4800 m (at 9.6 kbit/s) using 3 repeaters.
Type A (EN 50170 vol. 2).
Minimum 1 ms (at 12 Mbit/s)
Get_Master_Diag
Data_Exchange
- synchronous with PLC cycle.
- asynchronous, independent of PLC cycle (default).
Slave_Diag
- by configurator s/w (all CPU’s)
- by IOWR/IORD (C200HE/-G/-X and higher CPU models only).
Set_Prm
- automatic, at start-up.
Chk_Cfg
- automatic, at start-up.
PROFIBUS-DP GSD file
336
Global_Control
- Multi-cast / Broadcast of Sync, Freeze and Clear_Data
OC_1656.GSD
Programmable Controllers
C200HS
C200HW-PRM21
10
Model code
Maximum. number of Master Units
(with user defined I/O mapping)
Master Unit mounting position
Settings
Displays
External connectors
No. of IR words
No. of DM settings
No. of slave status words
Remote I/O
Max. No. of Slaves per
communications
Master Unit
Max. No. of I/O words
per
Master Unit
Slave diagnostics
PROFIBUS-DP
C200HE/HG/HX/CS1
C200HE-CPU11/32/42
C200HG-CPU33/43
C200HX-CPU34/44
C200HG-CPU53/63
C200HX-CPU54/64
CS1
CPU Rack or Expansion I/O Rack (classified as Special I/O Unit)
Unit cannot be mounted to SYSMAC BUS Slave Racks.
Unit cannot be used on a C200H PLC system.
Rotary switch : Unit number
Toggle switch : Bus termination
Unit status: RUN (green LED), ERR (red LED)
Network status: READY (green LED), COMM (green LED),
NW-ST (green LED), DP-ERR (red LED)
9-pin female sub-D connector (fieldbus connector, RS-485)
9-pin female sub-D connector (configurator connector, RS-232C)
2 words of control data out + 3 words of unit status in
18 words of unit setup information
16 words of status + diagnostic bits (location is user definable)
124
With default DM settings:
32 words in, 32 words out
With user defined DM settings:
80 words, in up to 4 areas
Programmable
Controllers
Unit Specification
10
16
With default DM settings:
50 words in, 50 words out
With user defined DM settings:
300 words in up to 4 areas;
maximum 100 words per area
via IOWR / IORD instructions
Not supported
9.6 / 19.2 / 93.75 / 187.5 / 500 kbit/s,
1.5 / 3 / 6 / 12 Mbit/s
as client : Data_Exchange, Slave_Diag, Set_Prm, Chk_Cfg, Global_Control
as server: Get_Master_Diag
Configurator program (SyConDP V.2.x) for WIN 95 and WIN NT
600 mA at 5 V DC (from PLC power supply)
–20 to +75°C
0 to +55°C
10% to 90% (non-condensing)
EN 50081-2
EN 61131-2
250 g
Baud rate
Supported
functions
Network configuration
Current consumption
Storage temperature
Operating temperature
Operating humidity
Conformance to EMC- and
environmental standards
Weight
Nomenclature
Unit Status
indicators
RUN (green)
ERR (red)
Unit Number
rotary switch
16 positions (0-F)
PRM21
RUN
ERR
READY
COMM
NW-ST
DP-ERR
MACHINE
No.
BUS
TERM
CONF
PROFIBUS-DP Master Unit
PROFIBUS-DP
Status indicators
READY (green)
COMM (green)
NW-ST (green)
DP-ERR (red)
PROFIBUS-DP
bus connector
RS-485
PROFIBUS-DP
termination switch
Configuration
connector
RS-232C
337
C200HW-PRT21
PROFIBUS-DP Slave Unit
T
I/O Link Unit for C200H# and CS1 PLC
Ideal for distributed control.
• OMRON’s C200HS, C200HE, C200HG, C200HX
and CS1 PLCs can be used as an intelligent Slave
on a PROFIBUS-DP network.
• Default 2 words in + 2 words out, maximum
100 words in + 100 words out.
• Simple PROFIBUS-DP node address setting by
rotary switches.
• Supports SYNC/FREEZE and Fail-Safe functions.
Specifications
Communication Specifications
Applicable standard
Station type
Bus connector
Bus termination
Baud rate (auto-detect)
PROFIBUS address range
Communication cable
Minimum slave interval time
Supported DP functions
PROFIBUS-DP GSD file
EN 50170 vol. 2
Modular station, max. 32 modules
Configurable with In-, Out- and I/O-modules of 1, 2, 4, 8 and 16 words
Total of 0 to 100 words in + 0 to 100 words out, with consistency over the full length
9-pin female sub-D connector (RS-485 PROFIBUS connector)
External
9.6 / 19.2 / 45.45 / 93.75 / 187.5 / 500 kbit/s,
1.5 / 3 / 6 / 12 Mbit/s
0 to 125, Remote setting not supported
Type A (EN 50170 vol. 2)
0.5 ms
Data_Exchange
Slave_Diag
Set_Prm
Chk_Cfg
Global_Control (SYNC, FREEZE, CLEAR)
Get_Cfg
RD_Imp
RD_Outp
OC_04AC.GSD
Unit Specifications
Host PLC system
Maximum number of Units per PLC system
C200HS, C200HE, C200HG, C200HX, CS1
C200HS
10
C200HE-CPU11/32/42
C200HG-CPU33/43
C200HX-CPU34/44
All others
16
Slave unit mounting position
CPU Rack or Expansion I/O Rack
Unit: cannot be mounted to SYSMAC BUS Slave Racks
Unit: cannot be used on a C200H PLC system
Current consumption
250 mA at 5 V DC (from PLC power supply)
Weight
180 g
Switch settings
Special I/O Unit number (0-F) by notary switch
PROFIBUS-DP mode address (o to 125) by 3 rotary switches
LED indicators
Unit status:
RUN (green LED), ERR (red LED)
Network status: COMM (green LED), BF (red LED)
No. of IR words
PLC to Slave Unit: 3 words (1 word of control data + 2 words slave input data)
Slave unit to PLC: 5 words (3 words of unit status + 2 words slave output data)
No. of DM settings
8 words of Unit setup information
Amount of I/O data per Unit
Default (DM settings all 0000)
all PLC’s: 2 words in + 2 words out
With user defined DM settings
C200HS: up to 80 words in + out
all others: up to 100 words in + 100 words out
Storage temperature
- 20 °C to + 75 °C
Operating temperature
0 °C to + 55 °C
Operating humidity
10% to 90% (non-condensing)
Conformance to EMC- and environmental standards EN50081-2
EN61131-2
338
Programmable Controllers
Programmable
Controllers
CS1W-DRM21
DeviceNet Unit
Multivender, Multibit Network
• Control of up to 32,000 points (2,000 words) per
master.
• Remote I/O communications can be allocated in any
area using DM settings.
• 16 DeviceNet Units can be mounted for each CPU
Unit (3 max. for fixed allocations).
• When using the Configurator (see note), remote I/O
can be allocated in an order independent of node
address.
Note: The Configurator is allocating a node-address if connected to DeviceNet using a DeviceNet communication card. It is not doing this if connected through the
serial communications interface of the CPU.
• DeviceNet Units can be used as a master and
a slave, and this functionality can be used simultaneously.
Note: DeviceNet Units allow DeviceNet networks to be
treated exactly like Controller Link, Ethernet, or other
networks for message communications or remote programming and monitoring by a CX-Programmer.
Function
OMRON supports the DeviceNet open field network, a multivender
network for machine/line control and information. The following types of
communications are possible.
1. Remote I/O communications for automatic data transfers between
the CPU Unit and Slaves (with no programming in the CPU Unit).
2. Explicit message communications. This can be programmed from
the CPU unit (IOWR and CMND instructions) and read from/write
to other DeviceNet units.
3. With explict message communication FINS commands can be
send to other devices that support FINS messaging.
System Configuration
DeviceNet Master Unit
Configurator
500 Kbps: 100 m
125 Kbps: 500 m
DeviceNet
DeviceNet I/O
Link Unit
Slaves
Non-I/O slaves
63 nodes max.
MULTIPLE I/O TERMINAL
DeviceNet Unit
339
Ordering Information
Compatible PLCs
CS1 Series
When used as a
master
When used as a
slave
Maximum number of I/O points
Fixed allocations
User-set allocations
Using allocated DM Area
words
Input: 8,000 points
Input: 1,024 points
Output: 1,024 points
Output: 8,000 points
Total: 16,000 points
Total: 2,048 points
(128 words)
(1,000 words)
Input: 16 points
Input: 1,600 points
Output: 16 points
Output: 1,600 points
Total: 32 points (2 words)
Total: 3,200 points
(200 words)
Model
Using Configurator
Input: 8,000 points x 2 blocks
Output: 8,000 points x 2 blocks
Total: 32,000 points (2,000 words)
CS1W-DRM21
Input: 1,600 points x 1 block
Output: 1,600 points x 2 blocks
Total: 4,800 points (300 words)
Specifications
Master/Slave Specifications
Communications power supply voltage
Remote I/O, explicit message service
11 to 25 V DC (supplied from the communications connector)
(See note 1.)
Communications:30 mA max.
Internal circuit:290 mA max.
63 (See note 2.)
Fixed allocations
2,048 points
Current consumption
Max. number of
connectable slaves
Max. number of I/O points
When used as a
master
When used as a
slave
User-set
Using allocated DM Area When used as a
allocations
words
master
When used as a
slave
Using Configurator
When used as a
master
When used as a
slave
Number of allocated words Fixed allocations
When used as a
master
When used as a
slave
User-set
Using allocated DM Area When used as a
allocations
words
master
When used as a
slave
Using Configurator
When used as a
master
When used as a
slave
Max. message length
Max. number of Units
Fixed allocations
mountable to PLC
User-set allocations
Weight
32 points
16,000 points
3,200 points
32,000 points
4,800 points
64 input and 64 output words
Software switch/status area: 25 words
1 input word, 1 output word (See note 3.)
500 input and 500 output words
Software switch/status area: 25 words
100 input and 100 output words (See note 3.)
Software switch/status area: 25 words
500 input words x 2 blocks, 500 output words x 2 blocks
Software switch/Status area: 25 words
100 input words x 1 blocks, 100 output words x 2 blocks
Software switch/Status area: 25 words
542 bytes (See note 4.)
3
16
172 g max.
Note: 1. Refer to the DeviceNet (CompoBus/D) Operation Manual (W267) for the communications power supply specifications.
2. The DeviceNet unit uses a node of the 64 supported by DeviceNet, leaves connection is possible to 63 slaves.
3. When the DeviceNet is used a slave, “input” and “output” respectively refer to input from the master to the slave and output from the slave
to the master.
4. The maximum message length includes the command code when using the CMND instruction.
5. The CS1W–DRM21 cannot perform message communications with the [email protected]@B. Use the [email protected]@B-V2, which is a later version. For details on the [email protected]@B-V2, refer to the catalog for the product itself (SGTD-017).
DeviceNet Unit
Classification
CS1 CPU Bus Unit
C200H Special I/O
Unit
Types of communications
Remote I/O communications master
(fixed or user-set allocations)
Remote I/O communications slave
(fixed or user-set allocations)
Message communications
Remote I/O communications master
Remote I/O communications slave
Specifications
Unit numbers
Up to 16 Units can be mounted 0 to F
when a Configurator is used. (Configurator required to mount 16
Units.)
Model
CS1W-DRM21
C200HW-DRM21-V1
C200HW-DRT21
DeviceNet Configurator
Model number
WS02-CFDC1-E
3G8E2-DRM21-E-V1
340
Specifications
Software only (Windows 95, 98, NT 4.0, 2000, or XP)
PC card with software (Windows 95 or 98)
Programmable Controllers
Programmable
Controllers
C200HW-DRM21-V1
DeviceNet Master Unit
Master Unit for CS1H, CS1G, C200HX,
C200HG, C200HE, and C200HS
• Incorporating a remote I/O and message communications functions.
• The Configurator is available for easy remote I/O
allocation.
• The control of a maximum of 300 words is possible
over remote I/O with the CS1H, CS1G, C200HX,
C200HG, or C200HE.
• The Configurator makes it possible for a single Programmable Controller to connect to up to 16 Master
Units.
Ordering Information
PLC
CS1H, CS1G,
C200HX,
C200HG,
C200HE
C200HS
Max. number of I/O points
Configurator not in Configurator in use
use
No message communications
1,600 points
Two-block inputs and two-block outputs (with a
(800 inputs/
maximum of 1,600 points or 100 words per
800 outputs)
block) and a total of 4,800 points or 300 words.
1,024 points
(512 inputs/
512 outputs)
Model
Message communications
Two-block inputs and two-block outputs (with a C200HW-DRM21-V1
maximum of 1,600 points or 100 words per
block) and a total of 1,600 points or 100 words.
Two-block inputs and two-block outputs (with a --maximum of 1,280 points or 80 words per block)
and a total of 1,280 points or 80 words.
Note: The DeviceNet Configurator is required for the Master Unit to be in configuration control.
Specifications
Unit Specifications
Communications power supply voltage
Current consumption
11 to 25 V DC (supplied from the communications connector) (See note 1.)
Communications:45 mA max. at 24 V DC
Internal circuit:250 mA max. at 5 V DC
Max. number of
Remote I/O
Configurator
CS1H/CS1G/C200HX/C200HG/C200HE:50 Units (See note 2.)
connectable Slaves (explicit mes- not in use
C200HS:32 Units (See note 2.)
sage service) Configurator in 63 (See note 3.)
use
FINS message service
8 (See note 4.)
Number of I/O
Configurator not in use
CS1H/CS1G/C200HX/C200HG/C200HE:1,600 points (800 input and 800 output points)
points
C200HS:1,024 points (512 input and 512 output points)
Configurator in use
CS1H/CS1G/C200HX/C200HG/C200HE:4,800 remote I/O points only, and 1,600 points
with messages used
C200HS:1,280 points
Number of
Configurator not in use (fixed CS1H/CS1G/C200HX/C200HG/C200HE:50 input and 50 output words and 10 words
allocated words
allocation)
for software switch/status area
C200HS:32 input and 32 output words with 10 words for
software switch/status area
Configurator in use
Input x 2 blocks, output x 2 blocks (with a maximum of 100 words per block) (See note 5.)
(free allocation)
Software switch/Status area: 10 words
Max. message length
160 kbytes
(for FINS or explicit
message)
Max. number
Configurator not in use
1
of Units
Configurator in use
10 Units (any C200HS-series CPU Unit or CS1H, CS1G or C200HX-, C200HG-, or C200HE-series CPU Unit with
mountable to PLC
a maximum of 880 I/O Points)
16 Units (any SYSMAC CS1H, CS1G or C200HX-, C200HG, or C200HE-series CPU Unit with a maximum of
880 I/O points)
Weight
250 g max.
Note: 1. Refer to the DeviceNet (CompoBus/D) Operation Manual (W267) for the communications power supply specifications.
2. The Master Unit uses a node. Therefore, set the PLC’s node numbers within a range of 50 to 63 if the number of CS1H, CS1G, C200HX,
C200HG, or C200HE PLCs connected to the Master Unit is 50 and within a range of 32 to 63.
3. The Master Unit uses one node. Therefore 63 Slave Units can be connected.
4. C200HS Series are not connected.
5. A maximum of 80 words per block can be used if the Master Unit is mounted to the C200HS Series.
DeviceNet Master Unit
341
C200HW-DRT21
DeviceNet I/O Link Unit
I/O Link Unit is ideal for distributed control.
PLC can be used as an Intelligent Slave on
the DeviceNet.
• Intelligent DeviceNet Slave
• Supports I/O and message communications.
• Maximum I/O area size:
512 input points (32 words)
512 output points (32 words)
• Programming Console or Configurator freely
allocates I/O areas.
Ordering Information
Name
I/O Link Unit (for SYSMAC CS1, C200HX/HG/HE)
Max. number I/O points
512 inputs, 512 outputs (1,024 points in total)
Model
C200HW-DRT21
Specifications
Ratings/Characteristics
General Specifications
Item
Communications power
supply voltage
Current consumption
Max. number of I/O points
Default area
No. of connectable Units
Weight
Specification
11 to 25 V DC
Communications power supply: 45 mA max.
Internal circuit power supply: 250 mA max. at 5 V DC
512 input points (32 words)
512 output points (32 words)
Write area (linking with Master’s write area): 1 word out of 350 IR words
Read area (linking with Master’s read area): 1 word out of 50 IR words
10 max. (CS1/C200HX/HG/HE CPU Unit handles up to 880 I/O points)
16 max. (CS1/C200HX/HG/HE CPU Unit handles more than 880 I/O points)
250 g max.
Function Specifications
Settings (Slave)
Item
Function
Allowable setting area
First address
Area size
Setting method
Specification
A write area block and a read area block can be freely allocated to any areas or addresses respectively
Both read and write areas can be allocated to IR, DM, HR, AR, LR, T/C, and EM areas
A readable or writable area by word (with some restrictions)
Set in 1-byte increments up to 64 bytes for both read and write areas
Configurator
Refer to the DeviceNet Configurator Operation Manual (W328).
Programming Console
1. Write the set value to I/O setting area allocated to the Special I/O Area.
2. Turn ON the software switch allocated to the Special I/O Area and write
the settings.
3. Turn the Programming Console OFF and ON or reset the AR area.
Message Communications
Item
Function
Master
Max. message size
Specification
Supports messages that can be written to or read from the CS1/C200HX/HG/HE’s user I/O areas (i.e., IR, DM, HR, AR, LR, T/C,
and EM areas)
OMRON’s Master Unit or compatible unit from Rockwell
Slave (C200HW-DRT21)
200 bytes per READ or WRITE command
Dimensions
35 × 130 × 101 mm (W × H × D)
Precautions
Refer to the relevant catalog for details on CS1-series and C200HX/HG/HE PLCs (CS1 Series: Cat. No. P047; C200HX/HG/HE: Cat. No. P036).
342
Programmable Controllers
Programmable
Controllers
C200HW-CORT21-V1
CAN & CANopen communication unit
CAN & CANopen communication unit
Supports CANopen, but can also be
used to communicate with a user-defined
CAN protocol
• PDO’s configurable with CANopen Configurator or
IOWR PLC instructions
• Able to transceive any user defined CAN message
up to 2000 msgs/s using IOWR PLC instructions
• Able to set any arbitrary baud rate supported by the
CAN controller
• Mountable on C200H Alpha and CS1 backplanes
System Configuration
CS1
C200HE/-HG/-HX
CS1
C200HE/-HG/-HX
C200HWCORT21-V1
C200HWCORT21-V1
CANopen
Third-party
devices
Frequency Inverter
CAN & CANopen communication unit
User-defined CAN
Devices with CAN
interface and a
proprietary protocol:
Aplications are:
- Test equipment
- Drives
- Cranes
- Lifts
- Tractors
343
Specifications
Installation
Host PLC system
Maximum number of Units per PLC system
Unit mounting position
Current consumption
Environment
User Interface
Network power supply
Weight
Storage temperature
Operating temperature
Operating humidity
Conformance to EMC- and environmental
standards
Switch settings
Indicators
PLC Interface
No. of IR words
No. of DM settings
Amount of I/O data per Unit
Network
interface
Message communications
CAN interface
Bus connector
Node address
Baud rate
Profile
Supported functions
EDS file
344
C200HE, C200HG, C200HX, CS1-series
C200HE
10
C200HG-CPU3#-E/CPU4#-E
C200HX-CPU3#-E/CPU4#-E
All others
16
CPU Rack of Expansion I/O Rack
Unit cannot be mounted to SYSMAC BUS Slave Racks
Internal I/O power supply: 250 mA at 5V DC max. (from PLC)
Network power supply:
45 mA max. (from communications connector)
24 V DC ± 10%
250 g
- 20 °C to + 75 °C
0 °C to + 55 °C
10 to 90% (non-condensing)
EN50081-2
EN61131-2
Special I/O Unit number (0~F) by rotary switch (front)
Network baud rate (10 kbit/s ~ 1000 kbit/s) by 3 DIP-switches (front)
CANopen node address (001 ~ 127) by 7 DIP-switches (rear)
Unit status:
RUN (green LED), ERR (red LED)
Network status:
2 x 7-segment display
PLC → Unit:
3 words (1 word control data + 2 words CANopen transmit data)
Unit → PLC:
5 words (3 words Unit status + 2 words CANopen receive data)
20 words
Default [DM settings all 0000]: 2 words in + 2 words out
With user defined DM settings: additionally up to 100 words in + 100 words out
By IOWR/IORD instructions
ISO 11898, High Speed CAN
5-pin mal open style connector
1 to 127, remote setting not supported
10, 20, 50, 125, 250, 500, 800, 1000 kbit/s
(Note: Refer to appendix D for the configuration of any arbitrary baud rate via the DM settings.)
Communication Profile DS301 version 4.0
Manufacturer Specific Application Profile
Boot-up type
Minimum
NMT
Slave
Number of PDOs
Max. 64 transmit PDOs and 64 receive PDOs
PDO transmission modes
Default:
Asynchronous
Configurable:
Synchronous cyclic
Synchronous acyclic
PDO linking
Supported
PDO mapping
Variable
Application objects
Default configuration:
Transmit objects: 4 x 8-bit
Receive objects: 4 x 8-bit
Additionally configurable:
Transmit objects: 8-bit (max. 100)
16-bit (max. 100)
32-bit (max. 50)
64-bit (max. 25)
Receive objects: 8-bit (max. 100)
16-bit (max. 100)
32-bit (max. 50)
64-bit (max. 25)
The total size of additonally configured transmit- and
receive objects is limited to 100 words each.
Number of SDOs
1 server
Emergency Message
EMCY Producer
Synchronisation
SYNC Consumer
Error control servies
Heartbeat (1 producer and 1 consumer) and
Node guarding
Storing of Parameters
Yes, can be stored in non-volatile memory
User defined CAN messages
Transmission using IOWR PLC instruction
Reception through configurable identifier filter
CORT21V1.eds
Programmable Controllers
Programmable
Controllers
C200HW-SRM21-V1
CompoBus/S Master Unit
CompoBus/S is a high-speed I/O bus
•
•
•
•
Up to 256 I/O points per Master.
Up to 32 Slaves per Master.
Communications cycle time: 0.5 ms (at 750 kbps).
Communications distance: Up to 500 m
(at 93.75 kbps).
Free wiring with any branching method for up to
200 m (in long-distance communications mode).
Function
System Configuration
A high-speed ON/OFF bus that automatically transfers remote I/O status to the CPU Unit without any programming in the CPU Unit. Highspeed remote I/O is supported by a communications cycle time of 1 ms
maximum for 256 I/O points.
CompoBus/S Master Unit
750 Kbps, 100 m
CompoBus/S network 93.75 Kbps, 500 m
Remote I/O
Slaves
32 Terminals max.
Specifications
General
Classification
C200H Special I/O Unit
Communications
Remote I/O
Specifications
No. of mountable Units: 16
Unit number
0 to F
Model
C200HW-SRM21-V1
Unit Specifications
Current consumption
Number of I/O points
Number of occupied words
PLC
Number of
Master Units
mountable
C200HE
C200HG-CPU33/43
C200HG-CPU53/63
C200HX-CPU34/44
C200HX-CPU54/64
C200HS
CS1
Number of points per node number
Max. number of Slaves per Master
Status data
Weight
Approved standards
150 mA max. at 5 V DC
256 points (128 inputs/128 outputs), 128 points (64 inputs/64 outputs) (switchable)
256 points:20 words (8 input words/8 output words, 4 status data)
128 points:10 words (4 input words/4 output words, 2 status data)
CS1, C200HX (-ZE), C200HG (-ZE), C200HE (-ZE), C200HS
128 points: 10, 256 points: 5
128 points: 10, 256 points: 5
128 points: 16, 256 points: 8
128 points: 10, 256 points: 5
128 points: 16, 256 points: 8
128 points: 10, 256 points: 5
128 points: 16, 256 points: 8
8 points
32
Communications Error Flag and Active Slave Node (see note)
200 g max.
UL 508 (E95399), CSA C22.2 No. 142 (LR51460)
These flags use the AR area.
CompoBus/S Master Unit
345
Communications Specifications
Communications method
Coding method
Connection method
Communications baud rate
Communications
High-speed communications
cycle time
mode
Long-distance
communications mode
Communications
cable
Communications
distance
High-speed communications
mode
Long-distance
communications mode
Max. number of connecting nodes
Error control checks
CompoBus/S protocol
Manchester coding method
Multi-drop method and T-branch method (see note 1)
750,000 bps, 93,750 bps (see note 2)
0.5 ms with 8 Slaves for inputs and 8 Slaves for outputs
0.8 ms with 16 Slaves for inputs and 16 Slaves for outputs
4.0 ms with 8 Slaves for inputs and 8 Slaves for outputs
6.0 ms with 16 Slaves for inputs and 16 Slaves for outputs
2-conductor VCTF cable (0.75 x 2), 4-conductor VCTF cable (0.75 x 4)
Special Flat Cable
2-conductor VCTF cable:
Main line length:100 m max.
Branch line length:3 m max.
Total branch line length:50 m max.
Special Flat Cable, 4-conductor VCTF cable:
Main line length:30 m max.
Branch line length:3 m max.
Total branch line length:30 m max.
(When Special Flat Cable is used to connect fewer than 16 Slaves, the main line can be up to 100 m long
and the total branch line length can be up to 50 m.)
2-conductor VCTF cable:
Main line length:500 m max.
Branch line length:6 m max.
Total branch line length:120 m max.
Special Flat Cable, 4-conductor VCTF cable:
Variable branch wiring (total cable length 200 m max.)
(There are no limits on the branching format or main, branch, or total line lengths.
The terminator must be connected to the point in the system farthest from the master.)
32
Manchester code check, frame length check, and parity check
Note: 1. A terminator must be connected to the point in the system most remote from the Master.
2. The communications baud rate is set by the DIP switch.
346
Programmable Controllers
Programmable
Controllers
Ordering Information
International Standards
The products shown in the attached tables are those that conform to the UL, CSA, cULus, cUL, NK, Lloyd’s Register, and EC Directives as of
September 2003.
(U: UL, C: CSA, UC: cULus, CU: cUL, N: NK, L: Lloyd, CE: EC Directives)
Please contact OMRON representative for application conditions.
CPU Rack
Name
CPU Units
(See note.)
CPU Backplanes
(for CS1 Units only)
CPU Backplanes
Power Supply Units
I/O Control Unit
Memory Cards
Serial Communications
Boards
Programming Consoles
Programming Console
Key Sheet
Programming Console
Connecting Cables
CX-Programmer
Peripheral Device
Connecting Cables
(for peripheral port)
Peripheral Device
Connecting Cables
(for RS-232C port)
USB-Serial Conversion
Cable
CX-Simulator
CX-Protocol
Battery Set
Specifications
I/O bits
Program
Data memory capacity
capacity
5,120
250 kSteps
448 kWords (DM: 32 kWords, EM: 32 kWords ×13 banks)
5,120
120 kSteps
256 kWords (DM: 32 kWords, EM: 32 kWords ×7 banks)
5,120
60 kSteps
128 kWords (DM: 32 kWords, EM: 32 kWords ×3 banks)
5,120
30 kSteps
64 kWords (DM: 32 kWords, EM: 32 kWords ×1 bank)
5,120
20 kSteps
64 kWords (DM: 32 kWords, EM: 32 kWords ×1 bank)
5,120
60 kSteps
128 kWords (DM: 32 kWords, EM: 32 kWords ×3 banks)
1,280
30 kSteps
64 kWords (DM: 32 kWords, EM: 32 kWords ×1 bank)
960
20 kSteps
64 kWords (DM: 32 kWords, EM: 32 kWords ×1 bank)
960
10 kSteps
64 kWords (DM: 32 kWords, EM: 32 kWords ×1 bank)
2 slots (Does not connect to Expansion Rack.)
3 slots
5 slots
8 slots
10 slots
2 slots (Does not connect to Expansion Rack.)
3 slots
5 slots
8 slots
10 slots
100 to 120 V AC or 200 to 240 V AC; Output capacity: 4.6 A, 5 V DC
100 to 120 V AC or 200 to 240 V AC (with 0.8 A, 24 V DC service power supply)
Output capacity: 4.6 A, 5 V DC
100 to 120 V AC or 200 to 240 V AC (with RUN output) Output capacity: 4.6 A, 5 V DC
100 to 120 V AC or 200 to 240 V AC (with RUN output) Output capacity: 9 A, 5 V DC
24 V DC, Output capacity: 4.6 A, 5 V DC
For Expansion Racks connected over a distance of more than 12 m (2 terminating resistors
included. C200H Units cannot be used on Long-distance Expansion Racks.)
Flash memory, 15 MB
Flash memory, 30 MB
Flash memory, 64 MB
Memory Card Adapter (for computer PCMIA slot)
2 × RS-232C ports, protocol macro function
1 × RS-232C port + 1 × RS-422/485 port, protocol macro function
An English Keyboard Sheet (CS1W-KS001-E) is required.
(Connects to peripheral port on CPU Unit only. Cannot be connected to RS-232C port.)
For C200H-PRO27 and CQM1-PRO01
Connects the CQM1-PRO01-E Programming Console. (Length: 0.05 m)
Connects the C200H-PRO27-E Programming Console. (Length: 2.0 m)
Connects the C200H-PRO27-E Programming Console. (Length: 6.0 m)
For 1 license
Windows-based Support Software for ladder programming on
Windows 95, 98, Me, NT 4.0, 2000 or XP
For 3 licenses
(Connects to peripheral port on CPU Unit or RS-232C port on
For 10 licenses
CPU Unit or Serial Communications Unit/Board.)
Connects DOS computers, D-Sub 9-pin receptacle (Length: 0.1 m)
(Conversion cable to connect RS-232C cable to peripheral port)
Peripheral bus or Host Link
Connects DOS computers, D-Sub 9-pin (Length: 2.0 m)
Connects DOS computers, D-Sub 9-pin (Length: 6.0 m)
Peripheral bus or Host Link, Connects DOS computers, D-Sub 9-pin (Length: 2.0 m)
antistatic
Connects DOS computers, D-sub 9-pin (Length: 5.0 m)
Host Link
Connects DOS computers, D-Sub 9-pin (Length: 2.0 m)
Connects DOS computers, D-Sub 9-pin (Length: 5.0 m)
Converts between USB and RS-232C, cable length: 0.5 m
PC driver provided on CD-ROM. Refer to Using a USB-Serial Conversion Cable to Connect to
a Peripheral or RS-232C Port on page 273 for specifications.
Windows-based Support Software for simulating ladder program operation on Windows 95, 98,
Me, NT 4.0, 2000 or XP
Windows-based Protocol Creation Software for Windows 95, 98, Me, NT 4.0, 2000 or XP
For CS1 Series only. (Install a replacement battery within 2 years of the production date.)
Model
---
Standards
---
CS1H-CPU67H
CS1H-CPU66H
CS1H-CPU65H
CS1H-CPU64H
CS1H-CPU63H
CS1G-CPU45H
CS1G-CPU44H
CS1G-CPU43H
CS1G-CPU42H
CS1W-BC022
CS1W-BC032
CS1W-BC052
CS1W-BC082
CS1W-BC102
CS1W-BC023
CS1W-BC033
CS1W-BC053
CS1W-BC083
CS1W-BC103
C200HW-PA204
C200HW-PA204S
U, C, N, L, CE
(N, L soon to
be received.)
C200HW-PA204R
C200HW-PA209R
C200HW-PD024
CS1W-IC102
U, C
U, C, N, L, CE
U, C, N, L, CE
U, C, CE
HMC-EF172
HMC-EF372
HMC-EF672
HMC-AP001
CS1W-SCB21-V1
CS1W-SCB41-V1
CQM1-PRO01-E
C200H-PRO27-E
CS1W-KS001-E
L, CE
U, C, N, L, CE
U, C, N, L, CE
U, C, N, L, CE
CE
U, C, N, L, CE
U, C, N, CE
CE
CS1W-CN114
CS1W-CN224
CS1W-CN624
[email protected]
[email protected]
[email protected]
CS1W-CN118
CS1W-CN226
CS1W-CN626
XW2Z-200S-CV
XW2Z-500S-CV
XW2Z-200S-V
XW2Z-500S-V
CS1W-CIF31
CE
---
---
WS02-SIMC1-E
---
WS02-PSTC1-E
CS1W-BAT01
--L, CE
Note: When using a CS1W-CN313 or CS1W-CN713 I/O Connecting Cable with a [email protected]@@H CPU Unit, use only Cables produced on or
after September 20, 2001 (production number 2091). Cables with no production number, a 6-digit production number, or produced before
September 20, 2001, cannot be used.
347
SYSMAC CS1D Duplex System
Name
CS1D CPU Units
Specifications
I/O capacity
Program capacity
5,120 points 60 Ksteps
250 Ksteps
Duplex Unit
CS1D Power Supply Units
Duplex CPU Backplane
Backplane for Online Unit
Replacement
Controller Link Units
Loop Control Board (LCB)
CX-Programmer
Optical Fiber Cable
Data memory capacity
128 Kwords
(DM: 32 Kwords, EM: 32 Kwords x 3 banks)
448 Kwords
(DM: 32 Kwords, EM: 32 Kwords x 13 banks)
--100 to 120 VAC or 200 to 240 VAC, 50/60 Hz (with RUN output)
Output capacity: 7 A, 5 VDC; 1.3 A, 26 VDC, 35 W total max.
24 VDC, Output capacity: 4.3 A, 5 VDC; 0.56 A, 26 VDC, 28 W total max.
5 slots
9 slots (Used both for CS1D Expansion Racks and CS1D Long-distance Expansion
Racks.)
Optical ring type with H-PCF cable
Optical ring type with GI cable
Processing method: Function blocks, Number of function blocks: 500 max., Supports duplex operation.
Windows-based Support Software for ladder programming on For 1 license
Windows 95, 98, Me, NT 4.0, 2000, or XP
For 3 licenses
For 10 licenses
H-PCF cable for Controller Link Units, cable length: 50 cm
Model
--CS1D-CPU65H
Standards
UC1, N, L, CE
CS1D-CPU67H
CS1D-DPL01
CS1D-PA207R
CS1D-PD024
CS1D-BC052
CS1D-BI092
CS1D-CLK12-V1
CS1D-CLK52-V1
CS1D-LCB05D
(See note.)
[email protected]
[email protected]
[email protected]
CS1D-CN051
UC1, N, CE
---
This Inner Board is sold only as a set with a CS1D CPU Unit. The set is the [email protected] CS1D Process-control CPU Unit.
348
Programmable Controllers
Name
CS1 Expansion Backplanes
(for CS1 Units only)
Specifications
3 slots
5 slots
8 slots
10 slots
CS1 Expansion Backplanes
3 slots
5 slots
8 slots
10 slots
C200H Expansion I/O Backplanes 3 slots
5 slots
8 slots
10 slots
Power Supply Units
100 to 120 V AC or 200 to 240 V AC, Output capacity: 4.6 A, 5 V DC
100 to 120 V AC or 200 to 240 V AC (with service supply: 0.8 A, 24 V DC), Output capacity: 4.6 A, 5 V DC
100 to 120 V AC or 200 to 240 V AC (with RUN output)
Output capacity: 4.6 A, 5 V DC
24 V DC
100 to 120 V AC or 200 to 240 V AC (with RUN output)
Output capacity: 9 A, 5 V DC
I/O Interface Unit
For Expansion Racks connected over a distance of more than 12 m. (C200H Units
cannot be used on Long-distance Expansion Racks.)
CS1 I/O Connecting Cables
Connects CS1 Expansion I/O Backplanes to CPU BackLength: 0.3 m
planes or other CS1 Expansion I/O Backplanes.
Length: 0.7 m
Length: 2 m
Length: 3 m
Length: 5 m
Length: 10 m
Length: 12 m
Long-distance Expansion Rack
Connect I/O Control Unit to I/O Interface Unit or connects Length: 0.3 m
Cables
two I/O Interface Units
Length: 0.6 m
Length: 1 m
Length: 2 m
Length: 3 m
Length: 5 m
Length: 10 m
Length: 20 m
Length: 30 m
Length: 40 m
Length: 50 m
CS1 to C200H I/O
Connects C200H Expansion I/O Backplanes to CPU Back- Length: 0.3 m
Connecting Cables
planes or CS1 Expansion I/O Backplanes.
Length: 0.7 m
Length: 2 m
Length: 3 m
Length: 5 m
Length: 10 m
Length: 12 m
C200H I/O Connecting
Connects C200H Expansion I/O Backplanes to other C200H Length: 0.3 m
Cables
Expansion I/O Backplanes.
Length: 0.7 m
Length: 2 m
Length: 5 m
Length: 10 m
Model
CS1W-BI032
CS1W-BI052
CS1W-BI082
CS1W-BI102
CS1W-BI033
CS1W-BI053
CS1W-BI083
CS1W-BI103
C200HW-BI031
C200HW-BI051
C200HW-BI081-V1
C200HW-BI101-V1
C200HW-PA204
C200HW-PA204S
Standards
U, C, N, L, CE
U, C, N, L, CE
U, C, N, L, CE
C200HW-PA204R
U, C
C200HW-PD024
C200HW-PA209R
U, C, N, L, CE
U, C, N, L, CE
CS1W-II102
U, C, CE
CS1W-CN313
CS1W-CN713
CS1W-CN223
CS1W-CN323
CS1W-CN523
CS1W-CN133
CS1W-CN133-B2
CV500-CN312
CV500-CN612
CV500-CN122
CV500-CN222
CV500-CN322
CV500-CN522
CV500-CN132
CV500-CN232
CV500-CN332
CV500-CN432
CV500-CN532
CS1W-CN311
CS1W-CN711
CS1W-CN221
CS1W-CN321
CS1W-CN521
CS1W-CN131
CS1W-CN131-B2
C200H-CN311
C200H-CN711
C200H-CN221
C200H-CN521
C200H-CN131
L, CE
N, L, CE
N, CE
CE
L, CE
N, L, CE
L, CE
349
Programmable
Controllers
Expansion Racks
I/O Units
Name
Specifications
AC Input Units
100 to 120 V AC,
8inputs
100 to 120 V AC,
16inputs
100 to 120 V AC,
16inputs
200 to 240 V AC,
8inputs
200 to 240 V AC,
16inputs
200 to 240 V AC,
16inputs
AC Input Units
100 to 120 V AC,
100 to 120 V DC,
16 inputs
200 to 240 V AC,
16 inputs
AC/DC Input Units 12 to 24 V AC/ V DC,
8inputs
24 V AC/ V DC,
16inputs
DC Input Units
24 V DC, 16 inputs,
7 mA
24 V DC, 32 inputs,
6 mA
24 V DC, 64 inputs,
6 mA
24 V DC, 96 inputs,
approx. 5 mA
DC Input Units
12 to 24 V DC, 8inputs
24 V DC, 16 inputs
Interrupt Input Unit 12 to 24 V DC,
8inputs
Interrupt
24 V DC, 16 inputs,
Input Unit
7 mA
B7A Input Units
16 inputs
32 inputs
High-speed Input
Unit
Safety Relay Unit
24 V DC, 16 inputs,
7 mA
24 V DC, 2 channels
with 4 inputs each,
4 pts/common
Relay Output Units 250 V AC or
120 V DC,
independent contacts,
8 outputs, 2 A
250 V AC or
120 V DC,
16 outputs, 2 A
Relay Output Units 250 V AC/24 V DC,
2 A, 8 outputs max.
250 V AC/24 V DC,
2 A, 12outputs max.
250 V AC/24 V DC, 2A,
12 outputs max.
250 V AC/24 V DC,
2 A, 16 outputs max.
250 V AC/24 V DC,
2 A, 16 outputs max.
250 V AC/24 V DC,
2 A, independent contacts, 5 outputs max.
250 V AC/24 V DC, 2 A,
independent contacts,
8 outputs max.
250 V AC/24 V DC, 2 A,
independent contacts,
8 outputs max.
350
Model
C200H-IA121
Mountable Racks
CPU Rack C200H
Expansion
I/O Racks
Yes
Yes
CS1
Expansion
Racks
Yes
CS1 Longdistance
Racks
No
Bits allocated Standards
SYSMAC (CIO 0000 to
BUS Slave CIO 0319)
Racks
Yes
16
U, C, N, L
C200H-IA122
Yes
Yes
Yes
No
Yes
16
C200H-IA122V
Yes
Yes
Yes
No
Yes
16
CE
C200H-IA221
Yes
Yes
Yes
No
Yes
16
U, C, N, L
C200H-IA222
Yes
Yes
Yes
No
Yes
16
C200H-IA222V
Yes
Yes
Yes
No
Yes
16
CE
CS1W-IA111
Yes
No
Yes
Yes
No
16
UC, N, CE
CS1W-IA211
Yes
No
Yes
Yes
No
16
C200H-IM211
Yes
Yes
Yes
No
Yes
16
C200H-IM212
Yes
Yes
Yes
No
Yes
16
CS1W-ID211
Yes
No
Yes
Yes
No
16
CS1W-ID231
Yes
No
Yes
Yes
No
32
CS1W-ID261
Yes
No
Yes
Yes
No
64
CS1W-ID291
Yes
No
Yes
Yes
No
96
U, C, N, L, CE
C200H-ID211
C200H-ID212
C200HS-INT01
Yes
Yes
Yes
U, C, N, L, CE
No
16
U, C, N, CE
C200H-B7AI1
C200H-B7A12
Yes
Yes
Yes
Yes
No
No
No
(See note 3)
Yes (See
note 4)
No
No
16
16
16
Yes
Yes
Yes
Yes
(See note 3)
Yes
(See note 4)
Yes
Yes
Yes
Yes
No
CS1W-INT01
Yes
Yes
Yes
(See note 3)
No
16
32
U, C, CE
U, C
CS1W-IDP01
Yes
No
Yes
Yes
Yes
No (See
note 2)
No
16
U, C, N, CE
CS1W-SF200
Yes
No
Yes
Yes
No
16
U, C, CE
CS1W-OC201
Yes
No
Yes
Yes
No
16
UC, N, CE
CS1W-OC211
Yes
No
Yes
Yes
No
16
C200H-OC221
Yes
Yes
Yes
No
Yes
16
C200H-OC222
Yes
Yes
Yes
No
Yes
16
C200H-OC222N
Yes
Yes
Yes
No
Yes
16
CE
C200H-OC225
Yes
Yes
Yes
No
Yes
16
U, C, N, L
C200H-OC226N
Yes
Yes
Yes
No
Yes
16
CE
C200H-OC223
Yes
Yes
Yes
No
Yes
16
U, C, N, L
C200H-OC224
Yes
Yes
Yes
No
Yes
16
C200H-OC224N
Yes
Yes
Yes
No
Yes
16
U, C, N, L, CE
U, C, N, CE
U, C, CE
U, C, N
CE
Programmable Controllers
Specifications
Transistor
Output Units
B7A Output Units
Triac Output Units
12 to 48 V DC, 1A,
8 sinking outputs
24 V DC, 2.1 A,
8sinking outputs
24 V DC, 0.8 A,
8sourcing outputs, load
short-circuit protection.
5 to 24 V DC, 0.3 A,
8sourcing outputs
24 V DC, 0.3 A,
12sinking outputs
5 to 24 V DC, 0.3 A,
12sourcing outputs
24 V DC, 0.3 A,
16sinking outputs
24 V DC, 1 A,
16sourcing outputs,
load short-circuit
protection.
16 outputs
32 outputs
250 V AC, 1.2 A,
8outputs
250 V AC, 0.3 A,
12outputs
250 V AC, 0.5 A,
12outputs
Transistor
12 to 24 V DC, 0.5A,
Output Units
16sinking outputs
24 V DC, 0.5A, 16
sourcing outputs
12 to 24 V DC, 0.5A,
32sinking outputs
24 V DC, 0.5A,
32sourcing outputs
12 to 24 V DC, 0.3A,
64sinking outputs
24 V DC, 0.3A,
64sourcing outputs
12 to 24 V DC, 0.1A,
96sinking outputs
12 to 24 V DC, 0.1A,
96sourcing outputs
Triac Output Units 250 V AC, 1.2 A,
8outputs
250 V AC, 0.5 A,
16outputs
DC Input/Transistor 24 V DC, 6 mA,
Output Units
32inputs, 12 to 24 V
DC, 0.3 A, 32 sinking
outputs
24 V DC, 6 mA,
32inputs, 24 V DC, 0.3
A, 32 sourcing outputs
24 V DC, approx. 5 A,
48inputs, 12 to 24 V
DC, 0.1 A, 48outputs,
sinking inputs/outputs
24 V DC, approx. 5A,
48inputs, 12 to 24 V
DC, 0.1 A, 48outputs,
sourcing inputs/outputs
Note: 1.
2.
3.
4.
Model
C200H-OD411
Mountable Racks
CPU Rack C200H
Expansion
I/O Racks
Yes
Yes
CS1
Expansion
Racks
Yes
CS1 Longdistance
Racks
No
Bits allocated Standards
SYSMAC (CIO 0000 to
BUS Slave CIO 0319)
Racks
Yes
16
U, C, N, L, CE
C200H-OD213
Yes
Yes
Yes
No
Yes
16
C200H-OD214
Yes
Yes
Yes
No
Yes
16
C200H-OD216
Yes
Yes
Yes
No
Yes
16
C200H-OD211
Yes
Yes
Yes
No
Yes
16
C200H-OD217
Yes
Yes
Yes
No
Yes
16
C200H-OD212
Yes
Yes
Yes
No
Yes
16
C200H-OD21A
Yes
Yes
Yes
No
Yes
16
C200H-B7AO1
C200H-B7A02
Yes
Yes
Yes
Yes
Yes
Yes
No
No
C200H-OA223
Yes
Yes
Yes
No
Yes
16
No
32
(See note 2)
Yes
16
C200H-OA222V
Yes
Yes
Yes
No
Yes
16
C200H-OA224
Yes
Yes
Yes
No
Yes
16
U, C, N, L
CS1W-OD211
Yes
No
Yes
Yes
No
16
U, C, N, CE
CS1W-OD212
Yes
No
Yes
Yes
No
16
CS1W-OD231
Yes
No
Yes
Yes
No
32
CS1W-OD232
Yes
No
Yes
Yes
No
32
CS1W-OD261
Yes
No
Yes
Yes
No
64
CS1W-OD262
Yes
No
Yes
Yes
No
64
CS1W-OD291
Yes
No
Yes
Yes
No
96
CS1W-OD292
Yes
No
Yes
Yes
No
96
CS1W-OA201
Yes
No
Yes
Yes
No
16
CS1W-OA211
Yes
No
Yes
Yes
No
16
CS1W-MD261
Yes
No
Yes
Yes
No
Inputs: 32
Outputs: 32
CS1W-MD262
Yes
No
Yes
Yes
No
Inputs: 32
Outputs: 32
CS1W-MD291
Yes
No
Yes
Yes
No
Inputs: 48
Outputs: 48
CS1W-MD292
Yes
No
Yes
Yes
No
Inputs: 48
Outputs: 48
U, C, N, L
U, C, N, L, CE
CE
U, C, CE
U, C
CE
U, C, N, L, CE
UC, N, CE
U, C, N, CE
U, C, N, L, CE
Interrupt Input Units cannot be used to input interrupts on any but the CPU Rack. They will function as normal I/O Units on other Racks.
C200H-B7A12/02/21/22 are C200H Group-2 Units.
The C200H-ID001 (no-voltage contacts, 8 inputs, NPN) and C200H-ID002 (no-voltage contacts, 8 inputs, PNP) cannot be used.
Interrupt input is not available when mounted on these Racks (i.e., used as normal I/O Unit).
351
Programmable
Controllers
Name
Connectors for C200H Group-2 High-density I/O Units
Part
Applicable connector
Terminal block
connection parts
Connection
Soldered
(included with Unit)
Model
C500-CE404
Crimped
C500-CE405
Pressure welded
1:1 connections
C500-CE403
[email protected]@@B
(See note 1.)
XW2B-40G4
XW2B-40G5
XW2D-40G6
[email protected]@@D
(See notes 1 and 2.)
XW2B-20G4
XW2B-20G5
XW2D-20G6
XW2C-20G5-IN16
Special Cable
Terminal Block Unit
1:2 connections
Special Cable
Terminal Block Unit
Remarks
From Fujitsu
Socket: FCN-361J040-AU
Connector bar: FCN-360C040-J2
From Fujitsu
Socket: FCN-363J040
Connector bar: FCN-360C040-J2
Contacts: FCN-363J-AU
From Fujitsu: FCN-367J040-AU
For CS1W-ID231/ID261/OD231/
OD232/OD261/OD262/MD261/
MD262 and C200H-ID216/ID217/
ID218/ID219/ID111/OD218/OD21B/
OD219
Standards
---
Note: 1. Refer to page 386 (Wiring Devices) for details. (Square boxes indicate the cable length.)
2. The [email protected]@@D, [email protected]@@, and [email protected]@@ cannot be connected. Only the inputs of the [email protected]@@ can be connected.
Connectors for CS1 High-density I/O Units
Part
Applicable connectors
Connection
Soldered
(included with Unit)
Model
CS1W-CE561
Remarks
From Fujitsu
Socket: FCN-361J056-AU
Connector bar: FCN-360C056-J3
CS1W-CE562
From Fujitsu
Socket: FCN-363J056
Connector bar: FCN-360C056-J3
Contacts: FCN-363J-AU
CS1W-CE563
From Fujitsu: FCN-367J056-AU
[email protected]@@H-1 (see note.) For CS1W-ID291/OD291/OD292/
MD291/MD292
XW2B-60G4
Crimped
Terminal block
Pressure welded
1:1
Special Cable
Terminal Block Unit
1:2
Special Cable
Terminal Block Unit
1:3
Special Cable
Terminal Block Unit
Standards
---
XW2B-60G5
[email protected]@@H-2 (see note.)
XW2B-20G4
XW2B-20G5
XW2D-20G6
XW2B-40G4
XW2B-40G5
XW2D-40G6
[email protected]@@H-3 (see note.)
XW2B-20G4
XW2B-20G5
XW2D-20G6
Note: Refer to page 386 (Wiring Devices) for details. (Square boxes indicate the cable length.)
C200H High-density I/O Units Classified as Special I/O Units
Name
Specifications
Model
Mountable Racks
CPU Rack C200H Expansion I/O
Racks
DC Input Units
TTL Input Units
Transistor Output Units
24 V DC, 32 inputs
5 V DC, 32 inputs
24 V DC, 32 sinking
outputs
5 V DC, 32 sinking
outputs
5 V DC, 16 inputs,
16 sinking outputs
24 V DC, 16 inputs,
16 sinking outputs
12 V DC, 16 inputs,
16 sinking outputs
C200H-ID215
C200H-ID501
C200H-OD215
Yes
Yes
Yes
Yes
Yes
Yes
Unit
CS1 Expan- CS1 Long- SYSMAC No.
sion Racks distance
BUS
Racks
Slave
Racks
Yes
No
Yes
0 to 9
Yes
No
Yes
Yes
No
Yes
C200H-OD501
Yes
Yes
Yes
No
Yes
C200H-MD501
Yes
Yes
Yes
No
Yes
C200H-MD215
Yes
Yes
Yes
No
Yes
C200H-MD115
Yes
Yes
Yes
No
Yes
TTL Output Units
TTL I/O Units
DC Input/Transistor
Output Units
352
Standards
U, C, N, L, CE
U, C, N
Programmable Controllers
Part
Applicable
connectors
Terminal block
connection parts
Connection
Soldered
(included with Unit)
Model
C500-CE241
Crimped
C500-CE242
Pressure welded
Special Cable
Terminal Block Connector
C500-CE243
[email protected]@@A (See note.)
XW2B-20G4
XW2B-20G5
XW2D-20G6
XW2B-20G5-D
XW2B-40G5-T
[email protected]@@A (see note)
XW2C-20G6-IN16
Special Cable
Terminal Block Connector
Remarks
From Fujitsu
Socket: FCN-361J024-AU
Connector bar: FCN-360C024-J2
From Fujitsu
Socket: FCN-363J024
Connector bar: FCN-360C024-J2
Contacts: FCN-363J-AU
From Fujitsu: FCN-367J024-AU/F
For C200H-ID215/ID501/OD215/
MD115/MD215
For C200H-ID215/ID501/MD115/
MD215/MD501
@@@ = cable length
Standards
---
Note: Refer to page 386 (Wiring Devices) for details. (Square boxes indicate the cable length.)
Special I/O Units
Name
Temperature
Control Units
Data Setting
Console
Heat/Cool
Temperature
Control Units
Specifications
Thermocouple input,
time-proportioning PID,
or ON/OFF transistor
output
Thermocouple input,
time-proportioning PID,
or ON/OFF voltage output
Thermocouple input,
PID current output
Temperature-resistance
thermometer input, timeproportioning PID, or
ON/OFF transistor output
Temperature-resistance
thermometer input, timeproportioning PID, or
ON/OFF voltage output
Temperature-resistance
thermometer input, PID
current output
Used with Temperature
Control Units.
Monitoring, setting, and
changing present values, set points, alarm
values, PID parameters,
bank numbers, etc.
Connecting
Cable, 2 m
Connecting
Cable, 4 m
Thermocouple input,
time-proportioning PID,
or ON/OFF transistor
output
Thermocouple input,
time-proportioning PID,
or ON/OFF voltage output
Thermocouple input,
PID current output
Temperature-resistance
thermometer input, timeproportioning PID, or
ON/OFF transistor output
Temperature-resistance
thermometer input, timeproportioning PID, or
ON/OFF voltage output
Temperature-resistance
thermometer input, PID
current output
Model
C200H-TC001
Mountable Racks
CPU
C200H ExRack
pansion I/O
Racks
Yes
Yes
C200H-TC002
Yes
C200H-TC003
CS1 Expansion Racks
Yes
CS1 Longdistance
Racks
No
SYSMAC
BUS Slave
Racks
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Yes
C200H-TC101
Yes
Yes
Yes
No
Yes
C200H-TC102
Yes
Yes
Yes
No
Yes
C200H-TC103
Yes
Yes
Yes
No
Yes
C200H-DSC01
---
C200H-CN225
---
C200H-CN425
---
C200H-TV001
Yes
Yes
Yes
No
Yes
C200H-TV002
Yes
Yes
Yes
No
Yes
C200H-TV003
Yes
Yes
Yes
No
Yes
C200H-TV101
Yes
Yes
Yes
No
Yes
C200H-TV102
Yes
Yes
Yes
No
Yes
C200H-TV103
Yes
Yes
Yes
No
Yes
Unit No.
Standards
0 to 9
U, C, CE
---
---
0 to 9
U, C, CE
353
Programmable
Controllers
Connectors for C200H High-density I/O Units
Name
Temperature
Sensor Units
Specifications
Thermocouple input, K/J
selectable
Thermocouple input, K/L
selectable
Temperature-resistance
thermometer,
JPt 100
Temperature-resistance
thermometer,
Pt 100
PID Control Units Voltage output/current
input, time-proportioning PID, or ON/OFF transistor output
Voltage output/current
input, time-proportioning PID, or ON/OFF voltage output
Voltage output/current
input, PID current output
Data Setting
Used with PID Control
Console
Units.
Monitoring, setting, and
changing present values, set points, alarm
values, PID parameters,
bank numbers, etc.
Connecting Cable, 2 m
Connecting Cable, 4 m
48 cam outputs (16 exCam
ternal outputs and 32 inPositioner
ternal outputs), Resolver
Unit
speed:
20 µs (5 kHz)
Data
Used with Cam PositionSetting
er Unit.
Console
Monitoring, setting, and
changing present values, set points, alarm
values, PID parameters,
bank numbers, etc.
Connecting Cable, 2 m
Connecting Cable, 4 m
ASCII Units
200-Kbyte RAM,
2 RS-232C ports
200-Kbyte RAM,
RS-232C port, RS-422/
485 port
200-Kbyte RAM,
3 RS-232C ports (
1 terminal only)
Analog Input Units 4 to 20 mA, 1 to 5/0 to 10
V (selectable), 4 inputs,
1/4,000 resolution
4 to 20 mA, 1 to 5/0 to 10
V/–10 to +10 V (selectable); 8 inputs;
1/4,000 resolution
4 to 20 mA, 1 to 5/0 to 10
V/–10 to +10 V (selectable); 8 inputs;
1/4,000 resolution
Ánalog Output
4 to 20 mA, 1 to 5/0 to 10
Units
V (selectable); 2 outputs;
1/4,075 resolution
4 to 20 mA, –10 to +10 V
(selectable), 4 outputs;
voltage: 1/8,190
current: 1/4,095
1 to 5 V, –10 to +10 V
(selectable), 8 outputs;
1/4,000 resolution
4 to 20 mA, 8 outputs; 1/
4,000 resolution
Analog I/O Units 2 inputs (4 to 20 mA,1 to
5 V, etc.)
2 outputs (4 to 20 mA, 1
to 5 V, etc.)
354
Model
CS1 Expansion Racks
C200H-TS001
Mountable Racks
CPU
C200H ExRack
pansion I/O
Racks
Yes
Yes
Unit No.
Standards
0 to 9
U, C
C200H-TS002
Yes
C200H-TS101
0 to 9
U, C, CE
---
---
0 to 9
U, C
---
---
0 to F
U, C, CE
Yes
0 to 9
U, C, N, L
No
Yes
0 to F
U, C, N, L, CE
Yes
No
Yes
Yes
Yes
No
Yes
0 to 9
U, C, N, L
Yes
Yes
Yes
No
Yes
0 to F
U, C, N, L, CE
C200H-DA003
Yes
Yes
Yes
No
Yes
C200H-DA004
Yes
Yes
Yes
No
Yes
C200H-MAD01
Yes
Yes
Yes
No
Yes
Yes
CS1 Longdistance
Racks
No
SYSMAC
BUS Slave
Racks
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Yes
C200H-TS102
Yes
Yes
Yes
No
Yes
C200H-PID01
Yes
Yes
Yes
No
Yes
C200H-PID02
Yes
Yes
Yes
No
Yes
C200H-PID03
Yes
Yes
Yes
No
Yes
C200H-DSC01
---
C200H-CN225
C200H-CN425
C200H-CP114
----Yes
C200H-DSC01
---
C200H-CN225
C200H-CN425
C200H-ASC11
----Yes
Yes
Yes
No
Yes
C200H-ASC21
Yes
Yes
Yes
No
Yes
C200H-ASC31
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
C200H-AD003
Yes
Yes
C200H-DA001
Yes
C200H-DA002
Yes
Yes
No
Yes
Programmable Controllers
Specifications
Customizable
Counter Units
Model
Pulse input: 2 pts Pulse
output: 2 pts Contact input: 12 pts Contact output: 8 pts
Pulse input: 1 pt, Analog
input: 1 pt, Analog output: 2pts, Contact input:
12 pts, Transistor outputs: 8 pts
Pulse input: 2 pts Analog
output: 2 pts Contact input: 12 pts Contact output: 8 pts
Contact input: 12 pts
Contact output: 8 pts
Analog Input Units 4 inputs (1 to 5 V, 0 to 5
V, 0 to 10 V, –10 to 10 V,
4 to 20 mA) Resolution:
1/4,000
8 inputs (1 to 5 V, 0 to 5
V, 0 to 10 V, –10 to 10 V,
4 to 20 mA) Resolution:
1/4,000
Analog Output
4 outputs (1 to 5 V, 0 to 5
Units
V, 0 to 10 V, –10 to 10 V,
4 to 20 mA) Resolution:
1/4,000
8 outputs (1 to 5 V, 0 to 5
V, 0 to 10 V, –10 to 10 V,
4 to 20 mA) Resolution:
1/4,000
8 outputs (4 to 20 mA)
Resolution: 1/4,000
Analog I/O Unit
4 inputs (4 to 20 mA, 1 to
5 V, etc.)
4 outputs (1 to 5 V, 0 to
10 V, etc.)
CS1W-HCP22-V1
Loop Control
Unit
CS1W-LC001
Process I/O Units
Isolated Thermocouple Input
Unit
Isolated Temperature- resistance
Thermometer
Input Unit
Isolated Temperature- resistance
Thermometer
Input Unit
(Ni508.4 Ω)
Isolated Twowire Transmission Device Input Unit
Isolated DC Input Unit
Control loops: 32
Processes: 250
Mountable Racks
CPU
C200H ExRack
pansion I/O
Racks
Yes
No
Unit No.
Standards
Yes
CS1 Longdistance
Racks
Yes
SYSMAC
BUS Slave
Racks
No
0 to 95
U, C, CE
Yes
No
Yes
Yes
No
0 to 95
U, C, N, L, CE
Yes
No
No
No
No
---
0 to F
Yes
No
Yes
Yes
No
0 to 95
U, C, CE
---
---
CS1 Expansion Racks
CS1W-HCA12-V1
CS1W-HCA22-V1
CS1W-HIO01-V1
CS1W-AD041-V1
CS1W-AD081-V1
CS1W-DA041
CS1W-DA08V
CS1W-DA08C
CS1W-MAD44
4 inputs, B, E, J, K, N, R, CS1W-PTS01-V1
S, T ±80 mV
4 inputs, Pt100, JPt
CS1W-PTS02
4 inputs, Ni508.4Ω
CS1W-PTS03
4 inputs, 4 to 20 mA, 1 to CS1W-PTW01
5V
4 inputs, 4 to 20 mA, 1 to CS1W-PDC01
5 V, 0 to 5 V, ±5 V, 0 to
10 V, ±10 V
4 inputs
CS1W-PPS01
Isolated Pulse
Input Unit
Isolated Control 4 outputs, 4 to 20 mA, 1
Output Unit
to 5 V
4 outputs, 0 to 10 V,
±10 V, 0 to 5 V, ±5 V,
0 to 1 V, ±1 V
Power Trans8 inputs, 0 to 1 mA, ±1
ducer Input Unit mA
100-mV DC In- 8 inputs, 0 to 100 mA,
put Unit
±100 mV
Support SoftSetting tool software for
ware
the Processing I/O Units,
OS: Windows 95, 98, NT
4.0 (see note)
CS1W-PMV01
CS1W-PMV02
CS1W-PTR01
CS1W-PTR02
WS02-PUTC1-E
---
355
Programmable
Controllers
Name
Name
High-speed
Counter Units
High-speed
Counter Units
SSI Unit
Motion Control
Units
MC Support
Software
Computer Connecting Cables
Specifications
Two-axis pulse input,
counting rate: 75 kcps
max., line driver compatible
Solder terminal; 40p and
a Connector Cover
Solderless terminal; 40p
and a Connector Cover
(Crimped)
Pressure welded terminal; 40p
Solder terminal; 40p and
a Connector Cover (Horizontal-type)
Crimp-style terminal;
40p and a Connector
Cover (Horizontal-type)
Pulse input: 2 pts Counting speed: 500 kcps
max.
Pulse input: 4 pts Counting speed: 500 kcps
max.
SSI encoder inputs:
2 channels
4 axes, analog outputs,
G language
2 axes, analog outputs,
G language
MCH high-speed serial
link
Windows 95, 98, or NT
Model
C200H-CT021
Mountable Racks
CPU
C200H ExRack
pansion I/O
Racks
Yes
Yes
C500-CE401
---
C500-CE402
---
C500-CE403
---
C500-CE404
---
C500-CE405
---
CS1W-CT021
Yes
No
Yes
Yes
No
0 to 92
U, C, CE
CS1W-CTS21
Yes
No
Yes
Yes
No
0 to 94
CE
CS1W-MC421
Yes
No
Yes
Yes
No
0 to 93
U, C, CE
Yes
CS1 Longdistance
Racks
No
SYSMAC
BUS Slave
Racks
Yes
Unit No.
Standards
0 to F
U, C, CE
---
---
CS1W-CT041
CS1W-MC221
CS1W-MCH71
[email protected]
Peripheral port on CPU CS1W-CN226 (2 m) --Unit
CS1W-CN626 (6 m)
RS-232C port on CPU XW2Z-200S-CV (2
Unit
m)
XW2Z-500S-CV (5
m)
Teaching Box
CVM1-PRO01
--Teaching Box Connecting Cable (2 m)
CV500-CN224
Memory Pack
CVM1-MP702
MC Terminal Block Conversion Unit for 2
XW2B-20J6-6
Axes (simplifies wiring I/O connectors)
MC Terminal Block Conversion Unit for 4
XW2B-40J6-7
Axes (simplifies wiring I/O connectors)
MC Terminal Block Conversion Unit Cable XW2Z-100J-F1
Motion Control
G-language programC200H-MC221
Yes
Units
mable, two-axis analog
outputs
MC Support Software
CV500-ZN3AT1-E
--IBM PC/AT or compatible
Connecting Cable: 3.3 m CV500-CIF01
--Teaching Box
CVM1-PRO01
--Connection cable for
CV500-CN224
--Teaching Box:
2 m long
Memory Pack
CVM1-MP702
--Terminal Block Conver- XW2B-20J6-6
--sion Unit
Simplifies wiring.
Connecting Cable for
XW2Z-100J-F1
--Terminal Block Conversion Unit
4 axes, analog+digital
C200HW-MC402-E Yes
I/O, Motion Perfect
BASIC language
356
CS1 Expansion Racks
0 to F
---
--CE
---
Yes
Yes
No
Yes
---
U, C, CE
CE
U, C, CE
---
0 to F
U, C, CE
---
---
U, C, CE
CE
U, C, CE
---
Yes
Yes
No
No
0 to F
CE
Programmable Controllers
Position Control
Units
Specifications
One-axis pulse-train
open-collector output
Two-axis pulse-train
open-collector output
Four-axis pulse-train
open-collector output
NC Support Software
(SYSMAC-NCT)
Peripheral Port Connecting Cables for computer
Model
C200HW-NC113
Mountable Racks
CPU
C200H ExRack
pansion I/O
Racks
Yes
Yes
C200HW-NC213
Yes
C200HW-NC413
Yes
WS01-NCTF1-E
---
CS1 Expansion Racks
Yes
CS1 Longdistance
Racks
No
SYSMAC
BUS Slave
Racks
Yes
Yes
Yes
No
Yes
Yes
Yes
No
Yes
CS1W-CN226 (2 m) --CS1W-CN626 (6 m)
RS-232C Port Connect- XW2Z-200S-CV
--ing Cables for computer (2 m)
NCT V1.11 or earlier
XW2Z-500S-CV
(5 m)
NCT V1.11 or earlier
XW2Z-200S (2 m)
(See note 1.)
XW2Z-500S (5 m)
(See note 1.)
1-axis Relay Unit for
XW2B-20J6-1B
C200HW-NC113
2-axis Relay Unit for
XW2B-40J6-2B
C200HW-NC213/
NC413
1-axis U, H, M Connect- XW2Z-050J-A6
ing Cables for C200HW- (0.5 m)
NC113
XW2Z-100J-A6 (1 m)
2-axis U, H, M Connect- XW2Z-050J-A7
ing Cables for C200HW- (0.5 m)
NC213/NC413
XW2Z-100J-A7 (1 m)
1-axis UEP Connecting XW2Z-050J-A8
Cables for C200HW(0.5 m)
NC113
XW2Z-100J-A8 (1 m)
2-axis UEP Connecting XW2Z-050J-A9
--Cables for C200HW(0.5 m)
NC213/NC413
XW2Z-100J-A9 (1 m)
Serial Communications Unit
RS-232C–RS422A Conversion Unit
Ethernet Unit
Controller Link
Units
Two RS-232C Ports
CS1W-SCU21-V1 Yes
1 RS-232C port and 1
RS-422A terminal
block
10Base-5
10Base-T
100Base-Tx
NT-AL001
Wired
Optical (H-PCF cable)
Optical
(GI fiber 62.5/125 µm)
Wired
Controller Link
Support Boards Optical (H-PCF cable)
Optical
(GI fiber 62.5/125 µm)
DeviceNet Unit Functions as master
and/or slave; allows
control of 2,048
points max. per master.
PROFIBUS-DP Master Unit
Unit
for up to 7000 remote
I/O words
Master Unit
for up to 300 remote
I/O words
I/O Link for up to
200 I/O words
CAN/CANopen Freely configurable
Unit
CAN communication, or CANopen
protocol
Standards
0 to F
U, C, CE
---
--CE
---
No
Yes
Yes
No
---
CS1W-ETN01
Yes
CS1W-ETN11
CS1W-ETN21
CS1W-CLK21-V1 Yes
Unit No.
---
---
0 to F
U, C, L, N,
CE
---
---
No
Yes
Yes
No
0 to F
U, C, L, N,
CE
No
Yes
Yes
No
0 to F
CS1W-CLK12-V1
CS1W-CLK52-V1
0 to F
U, C, L, N,
CE
U, C, CE
3G8F7-CLK21-V1 --3G8F7-CLK12-V1
3G8F7-CLK52-V1
---
CE
CS1W-DRM21
Yes
No
Yes
Yes
No
---
0 to F
CS1W-PRM21
Yes
No
Yes
Yes
No
0 to F
CE
Yes
Yes
No
No
C200HW-PRM21 Yes
C200HW-PRT21
C200HWCORT21-V1
U, L, C, CE
Yes
Yes
Yes
No
No
0 to F
U, C, CE
357
Programmable
Controllers
Name
Name
CX-Process
License Key
for Monitor
Software
Peripheral
Device Connecting Cables (for
peripheral
port)
Peripheral
Device Connecting Cables (for RS232C port)
Specifications
Model
For Loop Control
Unit, Programming
Tool and Monitor Tool
software, OS for Tool:
Windows 95, 98,
NT 4.0, OS for Monitor: Windows NT 4.0
(License key sold
separately)
Hardware key for
Monitor software,
with license
Connects DOS computers, D-Sub 9-pin
receptacle (Length:
0.1 m) (Conversion
cable to connect RS232C cable to peripheral port)
Peripheral bus or
Host Link, Connects
DOS computers, DSub 9-pin (Length:
2.0 m)
Peripheral bus or
Host Link, Connects
DOS computers, DSub 9-pin (Length:
6.0 m)
Peripheral bus or
Host Link, Connects
DOS computers, DSub 9-pin
(Length: 2.0 m)
Peripheral bus or
Host Link, Connects
DOS computers, DSub 9-pin
(Length: 5.0 m)
Mountable Racks
CPU
C200H ExRack
pansion I/O
Racks
CS1 Expansion Racks
CS1 Longdistance
Racks
Unit No.
Standards
SYSMAC
BUS Slave
Racks
WS02-LCTC1-J
---
---
---
WS02-LCTK1JL01
---
---
---
CS1W-CN118
---
---
---
CS1W-CN226
---
---
---
CS1W-CN626
---
---
---
XW2Z-200S-V
---
---
---
XW2Z-500S-V
---
---
---
Note: 1. A 25-pin to 9-pin adapter is required to connected to a 9-pin, D-sub RS-232C connector on an IBM PC/AT or compatible.
Note: Setting tool software for the Processing I/O Units also supports [email protected]@@, [email protected]@@, and CS1W-MAD44.
Optional Products
Name
I/O Unit Cover
Terminal Block Covers
C200H Unit Connector Cover
CS1 Special I/O Unit
Connector Cover
C200H Expansion I/O
Backplane Insulation Plates
Relay
Programming Console
Mounting Bracket
Space Unit
Terminating Resistor (See note.)
Specifications
Cover for 10-pin terminal block
Short protection for 10-pin terminal block (package of 10 covers); 8 pts
Short protection for 19-pin terminal block (package of 10 covers); 12 pts
Protective cover for unused I/O Connecting Cable connectors
Protective cover for unused I/O Connecting Cable connectors
Model
C200H-COV11
C200H-COV02
C200H-COV03
C500-COV01
CV500-COV01
Standards
---
Electrically insulate C200H Expansion I/O Backplanes from For 3-slot Backplane
the control panel to increase noise resistance.
For 5-slot Backplane
For 8-slot Backplane
For 10-slot Backplane
24 V DC, for C200H-OC221/OC222/OC223/OC224/OC225
Used to attach C200H-PRO27-E Hand-held Programming Console to a panel.
C200HW-ATT32
C200HW-ATT52
C200HW-ATT82
C200HW-ATTA2
G6B-1174P-FD-US
C200H-ATT01
N, L, CE
Used for empty I/O slot.
Mounts to end of CS1 Long-distance Expansion Rack
C200H-SP001
CV500-TER01
---
--U, C
Note: Two Terminating Resistors are included with the CS1W-IC102 I/O Control Unit.
Mounting Rails and Accessories
Name
DIN rail Mounting Bracket
DIN rails
End Plate
Spacer
358
Specifications
1 set (2 included)
Length: 50 cm; height: 7.3 cm
Length: 1 m; height: 7.3 cm
Length: 50 cm; height: 16 mm
---
Model number
C200H-DIN01
PFP-50N
PFP-100N
PFP-100N2
PFP-M
PFP-S
Standards
---
Programmable Controllers
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement