Laser Scanner Programming Guide (SE923 laser

Add to my manuals
48 Pages

advertisement

Laser Scanner Programming Guide (SE923 laser | Manualzz

Laser Scanner Programming Guide

(SE923 laser engine)

����������

CONTENT

Technical note ................................................................................................................................ 5

How to recognise the type of the laser barcode engine ............................................................ 5

How to program the laser barcode reader into default value ................................................... 6

Operational parameters ................................................................................................................ 6

Laser on Time ................................................................................................................................ 8

Aim Duration .................................................................................................................................. 8

Power Mode ................................................................................................................................... 8

Triggering Modes ........................................................................................................................... 9

Time-out Between Same Symbol .............................................................................................. 10

Transmit “No Read” Message .................................................................................................... 10

When disabled, if a symbol does not read, nothing is sent to the host. ................................ 10

Parameter Scanning .................................................................................................................... 11

Linear Code Type Security Level ................................................................................................ 11

Linear Security Level 1 ............................................................................................................ 11

Linear Security Level 2 ............................................................................................................ 11

Linear Security Level 2 ............................................................................................................ 12

Linear Security Level 3 ............................................................................................................ 12

Linear Security Level 4 ............................................................................................................ 12

Bi-directional Redundancy ......................................................................................................... 13

Enabling/disabling UPC-A bar code .......................................................................................... 13

Enabling/disabling UPC-E bar code .......................................................................................... 14

Enabling/disabling UPC-E1 bar code ................................................................................... 14

Enabling/disabling EAN-8 ........................................................................................................... 15

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

����������

Enabling/disabling EAN-13 ......................................................................................................... 15

Enabling/disabling Bookland EAN

........................................................................................ 16

Decode UPC/EAN Supplementals

........................................................................................ 16

Decode UPC/EAN Supplemental Redundancy

.................................................................. 17

Transmit UPC-A Check Digit

.................................................................................................. 17

Transmit UPC-E Check Digit

.................................................................................................. 18

Transmit UPC-E1 Check Digit

................................................................................................ 18

UPC-A Preamble

....................................................................................................................... 19

UPC-E Preamble

....................................................................................................................... 20

UPC E1 PREAMBLE

................................................................................................................. 20

Convert UPC-E to UPC-A

....................................................................................................... 21

Convert UPC-E1 to UPC-A

..................................................................................................... 21

EAN Zero Extend

....................................................................................................................... 22

Convert EAN-8 to EAN-13 Type

............................................................................................. 22

UPC/EAN Security Level

......................................................................................................... 23

UPC/EAN Security Level 0 ...................................................................................................... 23

UPC/EAN Security Level 1 ...................................................................................................... 23

UPC/EAN Security Level 2 ...................................................................................................... 24

UPC/EAN Security Level 3 ...................................................................................................... 24

UPC/EAN Coupon Code

.......................................................................................................... 24

CODE 128

................................................................................................................................... 25

Enable/Disable USS-128

......................................................................................................... 25

Enable/Disable UCC/EAN-128

............................................................................................... 25

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

����������

Enable/Disable ISBT 128

......................................................................................................... 25

CODE 39

...................................................................................................................................... 26

Enable/Disable Trioptic Code 39

........................................................................................... 26

Convert Code 39 to Code 32

.................................................................................................. 27

Code 32 Prefix

........................................................................................................................... 27

Set Lengths for Code 39

......................................................................................................... 28

One Discrete Length ............................................................................................................... 28

Two Discrete Lengths ............................................................................................................. 28

Length Within range ................................................................................................................ 29

Any Length ............................................................................................................................... 29

Code 39 Check Digit Verification ........................................................................................... 29

Transmit Code 39 Check Digit ................................................................................................ 30

Enable/Disable Code 39 Full ASCII ........................................................................................ 30

Code 93

....................................................................................................................................... 31

Set lengths for Code 93 .......................................................................................................... 31

Set Length for Code 93 ........................................................................................................... 32

Any Length ........................................................................................................................... 32

Interleaved 2 of 5

...................................................................................................................... 32

Set Lengths for Interleaved 2 of 5 .......................................................................................... 33

Length Within Range ........................................................................................................... 33

Any length ............................................................................................................................ 33

I 2 or 5 Check Digit Verification .............................................................................................. 34

Transmit I 2 of 5 Check Digit .................................................................................................. 34

Convert I 2 of 5 to EAN-13 ...................................................................................................... 35

Discrete 2 of 5

............................................................................................................................ 35

Set Lengths for Discrete 2 of 5 ............................................................................................... 36

Length Within Range ........................................................................................................... 36

Any length ............................................................................................................................ 36

Codabar.....................................................................................................................................37

Set Lengths for Codabar ........................................................................................................................37

Length Within Range ..........................................................................................................................38

Any length ............................................................................................................................................38

CLSI Editing .........................................................................................................................................38

NOTIS Editing ......................................................................................................................................39

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

����������

MSI Plessey

................................................................................................................................ 39

Set Lengths for MSI Plessey ..................................................................................................................40

Length Within Range ........................................................................................................... 40

Any length ............................................................................................................................................40

MSI Plessey Check Digits ......................................................................................................................41

Transmit MSI Plessey Check Digit .........................................................................................................41

MSI Plessey Check Digit Algorithm .......................................................................................................42

Transmit Code ID Character

.................................................................................................. 42

Prefix/Suffix Values

.................................................................................................................. 43

Scan Data Transmission Format

........................................................................................... 44

Scan Angle

................................................................................................................................. 45

Numeric Bar Codes

.................................................................................................................. 46

CANCEL

...................................................................................................................................... 47

Nordic ID International Headquarters

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

����������

Technical note

There are two types of laser barcode scanner engines used in RF-series hand terminals. This document applies to hand terminals with serial numbers above 46330. As a default the hand terminal reads most of the common barcode types. However, sometimes it is necessary to manually program it to support certain types of barcodes as well as different features of the barcodes. For the programming you need the hand terminal and this manual including special programming barcodes.

The hand terminals are programmed by reading the programming barcodes that can be found in this manual with the hand terminal’s barcode reader.

How to recognise the type of the laser barcode engine

The type of the laser barcode reader engine can be recognised by checking how the engine looks like through the laser lens window.

Note! Do not switch the laser reader on when you check the type of the laser barcode reader.

Se923 laser engine LM500 laser engine

Picture 1: This programming manual is valid for SE923 laser engine only. There is another document available at

Nordic ID internet pages with which you are able to program the LM500+ laser engine. This programming manual is valid for only RF-series products (PiccoLink RF600 and Nordic ID RF650/RF650Direct). Please note that sometimes the SE923 laser engine is located in the other side of the whole inside the laser lens; this is the case when the hand terminal is equipped also with an RFID reader/writer.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

5

����������

How to program the laser barcode reader into default value

Please make sure you are in the starting page by resetting the hand terminal (SHIFT+DEL). Please read the below barcode with the hand terminal by pressing the SCAN-button (the yellow button with barcode image marked on it). Note! Hand terminal does not acknowledge a successful reading e.g. by giving any beep – it only shuts down the laser beam immediately after a successful reading. Please note that if you have a hand terminal software version 4.8 or upper, all barcode scanning takes place under Settings (SHIFT+0), Choose

‘Laser Configuration’.

SET ALL DEFAULTS

Operational parameters

The SE-923 is shipped with the default settings shown in below Table 1. These default values are stored in non-volatile memory and are preserved even when the scanner is powered down. You can change the default values by scanning the appropriate bar codes included in this chapter. These new values replace the standard default values in memory. The default parameter values can be recalled by scanning the SET ALL

DEFAULTS bar code on previous page.

Below table lists the defaults for all parameters. If you wish to change any option, scan the appropriate bar code(s).

Parameter

Set Default Parameter

Laser on Time

Aim Duration

Power Mode

Trigger Mode

Time-out Between Same Symbol

Transmit “No Read” Message

Parameter Scanning

Linear Code Type Security Levels

Bi-directional Redundancy

UPC/EAN

UPC-A

UPC-E

UPC-E1

EAN-8

EAN-13

Bookland EAN

Decode UPC/EAN Supplementals

Decode UPC/EAN Supplemental Redundancy

Default

All Defaults

3.0 sec

0.00 sec

Low Power

Level

1.0 sec

Disable

Enable

1

Disable

Enable

Enable

Disable

Enable

Enable

Disable

Ignore

7

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

6

����������

Transmit UPC-A Check Digit

Transmit UPC-E Check Digit

Transmit UPC-E1 Check Digit

UPC-A Preamble

UPC-E Preamble

UPC-E1 Preamble

Convert UPC-E to A

Convert UPC-E1 to A

EAN-8 Zero Extend

Convert EAN-8 to EAN-13 Type

UPC/EAN Security Level

UPC/EAN Coupon Code

Code 128

USS-128

UCC/EAN-128

ISBT 128

Code 39

Code 39

Trioptic Code 39

Convert Code 39 to Code 32

Code 32 Prefix

Set Length(s) for Code 39

Code 39 Check Digit Verification

Transmit Code 39 Check Digit

Code 39 Full ASCII Conversion

Code 93

Code 93

Set Length(s) for Code 93

Interleaved 2 of 5

Interleaved 2 of 5

Set Length(s) for I 2 of 5

I 2 of 5 Check Digit Verification

Transmit I 2 of 5 Check Digit

Convert I 2 of 5 to EAN 13

Discrete 2 of 5

Discrete 2 of 5

Set Length(s) for D 2 of 5

Codabar

Codabar

Set Length(s) for Codabar

CLSI Editing

NOTIS Editing

MSI Plessey

MSI Plessey

Set Length(s) for MSI Plessey

MSI Plessey Check Digits

Transmit MSI Plessey Check Digit

MSI Plessey Check Digit Algorithm

Data Options

Transmit Code ID Character

Prefix/Suffix Values

Prefix

Suffix 1

Suffix 2

Scan Data Transmission Format

Scan Angle

Scan Angle

Enable

Enable

Enable

Enable

Disable

Disable

Disable

2-55

Disable

Disable

Disable

Enable

Enable

Enable

System Character

System Character

System Character

Disable

Disable

Disable

Type is EAN-13

0

Disable

Disable

4-55

Enable

14

Disable

Disable

Disable

Disable

12

Disable

5-55

Disable

Disable

Disable

6-55

One

Disable

Mod 10/Mod 10

None

NULL

LF

CR

Data as is

Normal Width

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

7

����������

Laser on Time

This barcode sets the maximum time decode processing continues during a scan attempt. It is programmable in 0.1 second increments from 0.5 to 9.0 seconds. To set a Laser On Time, scan the bar code below. Next scan two numeric bar codes on page 46 that correspond to the desired on time. Times less than 1.0 second must have a leading zero. For example, to set an on time of 0.5 seconds, scan the bar code below, then scan the “=” and “5” bar codes. If you make an error, or wish to change your selection, scan the CANCEL bar code on page 47.

Aim Duration

The aim mode is programmable in 0.1 second increments from 0.0 to 9.9 seconds. No aim pattern is visible when the value is 0.0.

To set aim duration, scan the bar code below. Next scan two number bar codes beginning on page 46 that correspond to the desired aim duration. Times less than 1.0 second must have a leading zero. For example, to set an aim duration of 0.5 seconds, scan the bar code below, then scan the “0” and “5” bar codes. If you make an error , or wish to change your selection, scan the CANCEL bar code on page 47.

Power Mode

This parameter determines whether or not power remains on after a decode attempt. When in Low Power mode, the scanner enters into a low power consumption mode whenever possible, provided all WAKEUP signals have been released. When in Continuous On mode, power remains on after each decode attempt.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

8

����������

Triggering Modes

Choose one of the options below to trigger the scan engine.

Level

Pulse

Continuous

Blinking

Host

A trigger pull activates the laser and decode processing. The laser remains on, and decode processing continuous until a trigger release, a valid decode, or the Laser On Time-out is reached.

A trigger pull activates the laser and decode processing. The laser remains on and decode processing continues until a valid decode, or the Laser On Time-out is reached.

The laser is always on and decoding.

This trigger mode is used for triggerless ScanStand operation.

Scanning range is reduced in this mode. This mode cannot be used with scanners that support an aim mode.

Triggering signal comes from a host command. Any actual trigger pull will be interpreted by the scan engine as level triggering option.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

9

����������

Time-out Between Same Symbol

When in Continuous triggering mode, this parameter sets the minimum time that must elapse before the scanner decodes a second bar code which is identical to one which has just been decoded. This reduces the risk of accidentally scanning the same symbol twice. It is programmable in 0.1 second increments from

0.00 to 9.9 seconds.

To set a time-out between same symbol, scan the bar code below. Next scan two numeric bar codes beginning on page 46 that correspond to the desired time-out. Times les than 1.0 second must have a leading zero. For example, to set a time-out of 0.5 seconds, scan the bar code below, then scan the “0” and

“5” bar codes. If you make an error, or wish to change your selection, scan the CANCEL barcode on page

47.

Transmit “No Read” Message

When enabled, if a symbol does not decode, “NR” is transmitted. Any prefix or suffixes which have been enabled are appended around this message.

When disabled, if a symbol does not read, nothing is sent to the host.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

10

����������

Parameter Scanning

To disable decoding of parameter bar codes, scan the bar code below. Note that the Set Defaults parameter bar code will still be decoded. To enable decoding of parameter bar codes, scan ENABLE PARAMETER

SCANNING, SET ALL DEFAULTS.

Linear Code Type Security Level

The scanner offers four levels of decode security for linear code types (e.g. Code 39, Interleaved 2 of 5).

Please note this does not apply to Code 128. Higher security levels are selected for decreasing levels of bar code quality. AS security levels increase, the scanner’s aggressiveness decreases.

Linear Security Level 1

The following code types must be successfully read twice before being decoded:

Length

All

4 or less

8 or less

8 or less

Code Type

Codabar

MSI Plessey

Discrete 2 of 5

Interleaved 2 of 5

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

11

����������

Linear Security Level 2

The following code types must be successfully read twice before being decoded:

Code Type

All

Length

All

Linear Security Level 3

Code types other than the following must be successfully read twice before being decoded. The following codes must be read three times:

Code Type

MSI Plessey

Discrete 2 of 5

Interleaved 2 of 5

Length

4 or less

8 or less

8 or less

Linear Security Level 4

The following code types must be successfully read three times before being decoded:

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

12

����������

Bi-directional Redundancy

This parameter is only valid when a Linear Code Type Security Level has been enabled. When this parameter is enabled, a bar code must be successfully scanned in both directions (forward and reverse) before being decoded.

Enabling/disabling UPC-A bar code

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

13

����������

Enabling/disabling UPC-E bar code

Enabling/disabling UPC-E1 bar code

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

14

����������

Enabling/disabling EAN-8

Enabling/disabling EAN-13

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

15

����������

Enabling/disabling Bookland EAN

Decode UPC/EAN Supplementals

Supplementals are additionally appended characters (2 or 5) according to specific code format conventions

(e.g. UPC a+2, UPC E+2, EAN 8+2). Three options are available:

• If UPC/EAN with supplemental characters is selected, UPC/EAN symbols without supplemental characters are not decoded.

• If UPC/EAN without supplemental characters is selected, and the scanner is presented with a

UPC/EAN plus supplemental symbol, the UPC/EAN is decoded and the supplemental characters ignored.

• An autodiscriminate option is also available. If this option is selected, scan Decode UPC/EAN

Supplemental Redundancy on page 17, then select a value form the numeric bar codes beginning on page 46. A value of 5 or more is recommended.

Note: In order to minimize the risk of invalid data transmission, the scanner manufacturer recommends that you select whether to read or ignore supplemental characters.

Select the desired option by scanning one of the below bar codes.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

16

����������

Decode UPC/EAN Supplemental Redundancy

With Autodiscriminate UPC/EAN Supplementals selected, this option adjusts the number of times a symbol without supplementals will be decoded before transmission. The range is from 2 to 20 times. Five or above is recommended when decoding a mix of UPC/EAN symbols with and without supplementals, and the autodiscriminate option is selected.

Scan the bar code below to select a decode redundancy value. Next scan two numeric bar code beginning on page 46. Single digit numbers must have a leading zero. If you make an error, or wish to change your selection, scan the CANCEL bar code on page 47.

Transmit UPC-A Check Digit

Scan the appropriate bar code below to transmit the symbol with our without the UPC-A check digit.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

17

����������

Transmit UPC-E Check Digit

Scan the appropriate bar code below to transmit the symbol with or without the UPC-E check digit.

Transmit UPC-E1 Check Digit

Scan the appropriate bar code below to transmit the symbol with or without the UPC-E1 check digit.

Nordic ID International Headquarters

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

18

����������

UPC-A Preamble

Three options are given for lead-in characters for UPC-A symbols transmitted to the host device: transmit system character only, transmit system character and country code, and no preamble transmitted. The lead-in characters are considered part of the symbol.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

19

����������

UPC-E Preamble

Three options are given for lead-in characters for UPC-E symbols transmitted to the host device: transmit system character only, transmit system character and country code, and no preamble transmitted. The lead-in characters are considered part of the symbol.

UPC E1 Preamble

Three options are given for lead-in characters for UPC-E1 symbols transmitted to the host device: transmit system character only, transmit system character and country code, and no preamble transmitted. The lead-in characters are considered part of the symbol.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

20

����������

Convert UPC-E to UPC-A

This parameter converts UPC-E (zero suppressed) decoded data to UPC-A format before transmission. After conversion, data follows UPC-A format and is affected by UPC-A programming selections (e.g. Preamble,

Check Digit).

Scanning DO NOT CONVERT UPC-E TO UPC-A allows you to transmit UPC-E (zero suppressed) decoded data.

Convert UPC-E1 to UPC-A

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

21

����������

EAN Zero Extend

When this parameter is enabled, five leading zeros are added to decoded EAN-8 symbols to make them compatible in format to EAN-13 symbols. Disabling this parameter returns EAN-8 symbols to their normal format.

Convert EAN-8 to EAN-13 Type

When EAN Zero Extend is enabled, this parameter gives you the option of labeling the extended symbol as either an EAN-13 bar code, or an EAN-8 bar code. This affects Transmit Code ID Character and DECODE_

DATA message. When EAN Zero Extend is disabled, this parameter has no effect on bar code data.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

22

����������

UPC/EAN Security Level

The scanner offers four levels of decode security for UPC/EAN bar codes. Increasing levels of security are provided for decreasing levels of bar code quality. There is an inverse relationship between security and scanner aggressiveness, so be sure to choose only that level of security necessary for any given application.

UPC/EAN Security Level 0

This is the default setting which allows the scanner to operate in its most aggressive state, while providing sufficient security in decoding “in-spec” UPC/EAN bar codes.

UPC/EAN Security Level 1

As bar code quality levels diminish, certain characters become prone to mis-decodes before others (i.e. 1,

2, 7, 9). If you are experiencing mis-decodes of poorly printed bar codes, and the mis-decodes are limited to these characters, select this security level.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

23

����������

UPC/EAN Security Level 2

If you are experiencing mis-decodes of poorly printed bar codes, and the mis-decodes are not limited to characters 1, 2, 7 and 8, select this security level.

UPC/EAN Security Level 3

If you have tried Security Level 2, and are still experiencing misdecodes, select this security level. Be advised, selecting this option is an extreme measure against mis-decoding severely out of spec bar codes.

Selection of this level of security significantly impairs the decoding ability of the scanner. If this level of security is necessary, you should try to improve the quality of your bar codes.

UPC/EAN Coupon Code

When enabled, this parameter decodes UPC-A, UPC-A with 2 supplemental characters, UPC-A with 5 supplemental characters, and UPC-A/EAN128 bar codes. Autodiscriminate UPC/EAN Supplementals must be enabled.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

24

����������

CODE 128

Enable/Disable USS-128

Enable/Disable UCC/EAN-128

Enable/Disable ISBT 128

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

25

����������

CODE 39

Enable/Disable Trioptic Code 39

Trioptic Code 39 symbols always contain six characters. Trioptic Code 39 and Code 39 Full ASCII should not be enabled simultaneously.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

26

����������

Convert Code 39 to Code 32

Code 32 Prefix

Enable this parameter to add the prefix to add the prefix character “A” to all Code 32 bar codes.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

27

����������

Set Lengths for Code 39

Lengths for Code 39 may be set for any length, one or two discrete lengths, or lengths within a specific range. The length of a code refers to the number of characters (i.e. human readable characters), including check digit(s) the code contains. If Code 39 Full ASCII is enabled, Length Within a Range or Any Length are the preferred options.

One Discrete Length

This option allows you to decode only those codes containing a selected length. For example, if you select

Code 39 One Discrete Length, then scan 1, 4, only Code 39 symbols containing 14 characters are decoded.

Numeric bar codes begin on page 46. If you make an error, or wish to change your selection, scan the

CANCEL bar code on page 47.

Two Discrete Lengths

This option allows you to decode only those codes containing two selected lengths. For example, if you select Code 39 Two Discrete Lengths then scan 0, 2, 1, 4 only Code 39 symbols containing 2 or 14 characters are decoded. Numeric bar codes begin on page 46. If you make an error, or wish to change your selection, scan the CANCEL bar code on page 47.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

28

����������

Length Within range

This option allows you to decode a code type within a specified range. For example, to decode Code 39 symbols containing between 4 and 12 characters, first scan Code 39 Length Within Range. Then scan 0,4,1 and 2 (single digit numbers must always be preceded by a leading zero). Numeric bar codes begin on page

46. If you make an error, or wish to change your selection, scan the CANCEL bar code on page 47.

Any Length

Scanning this option allows you to decode Code 39 symbols containing any number of characters.

Code 39 Check Digit Verification

When enabled, this parameter checks the integrity of a Code 39 symbol to ensure it complies with specified algorithms. Only those Code 39 symbols which include a modulo 43 check digit are decoded when this parameter is enabled.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

29

����������

Transmit Code 39 Check Digit

Scan this symbol if you want to transmit the check digit with the data.

Scan this symbol if you want to transmit the data without the check digit.

Enable/Disable Code 39 Full ASCII

To enable or disable Code 39 Full ASCII, scan the appropriate bar code below. When enabled, the ASCII character set assigns a code to letters, punctuation marks, numerals, and most control keystrokes on the keyboard. The first 32 codes are non-printable and are assigned to keyboard control characters such as

BACKSPACE and RETURN. The other 96 are called printable codes because all but SPACE and DELETE produce visible characters.

Code 39 Full ASCII interprets the bar code special character ($ + % /) preceding a Code 39 character and assigns an ASCII character value to the pair. For example, when Code 39 Full ASCII is enabled and a +B is scanned, it is interpreted as b, %J as ?, and $H emulates the keystroke BACKSPACE. Scanning ABC$M outputs the keystroke equivalent of ABC ENTER.

Code 39 full ASCII and Trioptic Code 39 should not be enabled simultaneously. The scanner does not autodiscriminate between Code 39 and Code 39 Full ASCII.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

30

����������

Code 93

Set lengths for Code 93

Lengths for Code 93 may be set for any length, one or two discrete lengths, or lengths within a specific range. The length of a code refers to the number of characters (i.e. human radable characters), including check digit(s) the code contains.

One & two discrete Lengths – Please see explanation on one & two discrete lengths on preceding chapter about Code 39.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

31

����������

Set Length for Code 93

Please see explanation on length within range on preceding chapter about Code 39.

Any Length

Scanning this option allows you to decode Code 93 symbols containing any number of characters.

Interleaved 2 of 5

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

32

����������

Set Lengths for Interleaved 2 of 5

Lengths for I 2 of 5 may be set for any length, one or two discrete lengths, or lengths within a specific range.

The length of a code refers to the number of characters (i.e. human readable characters), including check digit(s) the code contains.

One & two discrete Lengths – Please see explanation on one & two discrete lengths on preceding chapter about Code 39.

Length Within Range

Please see explanation on length within range on chapter about Code 39.

Any length

Scanning this option allows you to decode I 2 of 5 symbols containing any number of characters. (Note:

Selecting this option may lead to misdecodes for I 2 of 5 codes).

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

33

����������

I 2 or 5 Check Digit Verification

When enabled, this parameter checks the integrity of an I 2 of 5 symbol to ensure it complies with a specified algorithm, either USS (Uniform Symbology Specification), or OPCC (Optical Product Code Council).

Transmit I 2 of 5 Check Digit

Scan this symbol if you want to transmit the check digit with the data.

Scan this symbol if you want to transmit the data without the check digit.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

34

����������

Convert I 2 of 5 to EAN-13

This parameter converts a 14 character I 2 of 5 code into EAN-13, and transmits to the host as EAN-13. In order to accomplish this, the I 2 of 5 code must be enabled, one length must be set to 14, and the code must have a leading zero and a valid EAN-13 check digit.

Discrete 2 of 5

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

35

����������

Set Lengths for Discrete 2 of 5

Lengths for Discrete 2 of 5 may be set for any length, one or two discrete lengths, or lengths within a specific range. The length of a code refers to the number of characters (i.e. human readable characters), including check digit(s) the code contains.

One & two discrete Lengths – Please see explanation on one & two discrete lengths on chapter about Code

39.

Length Within Range

Please see explanation on length within range on chapter about Code 39.

Any length

Scanning this option allows you to decode D 2 of 5 symbols containing any number of characters. (Note:

Selecting this option may lead to misdecodes for D 2 of 5 codes).

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

36

����������

Codabar

Set Lengths for Codabar

Lengths for Codabar may be set for any length, one or two discrete lengths, or lengts within a specific range. The length of a code refers to the number of characters (i.e. human readable characters) the code contains. It also includes any start or stop characters.

One & two discrete Lengths – Please see explanation on one & two discrete lengths on chapter about Code

39.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

37

����������

Length Within Range

Please see explanation on length within range on chapter about Code 39.

Any length

Scanning this option allows you to decode Codabar symbols containing any number of characters.

CLSI Editing

When enabled, this parameter strips the start and stop characters and inserts a space after the first, fifth, and tenth characters of a 14-character Codabar symbol. (Note: Symbol length does not include start and stop characters).

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

38

����������

NOTIS Editing

When enabled, this parameter strips the start and stop characters from decoded Codabar symbol.

MSI Plessey

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

39

����������

Set Lengths for MSI Plessey

Lengths for MSI Plessey may be set for any length, one or two discrete lengths, or lengths within a specific range. The length of a code refers to the number of characters (i.e. human readable characters) the code contains. It also includes any start or stop characters.

One & two discrete Lengths – Please see explanation on one & two discrete lengths on chapter about Code

39.

Length Within Range

Please see explanation on length within range on chapter about Code 39.

Any length

Scanning this option allows you to decode MSI Plessey symbols containing any number of characters.

(Note: Selecting this option may lead to misdecodes for MSI Plessey codes).

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

40

����������

MSI Plessey Check Digits

These check digits at the end of the bar code verify the integrity of the data. At least one check digit is always required. Check digits are not automatically transmitted with the data.

If two check digits are selected, an MSI Plessey Check Digit Algorithm must also be selected.

Transmit MSI Plessey Check Digit

Scan this symbol if you want to transmit the check digit with the data.

Scan this symbol if you want to transmit the data without the check digit.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

41

����������

MSI Plessey Check Digit Algorithm

When the Two MSI Plessey check digits option is selected, an additional verification is required to ensure integrity. Either of the two following algorithms may be selected.

Transmit Code ID Character

A

B

D

E

G

J

K

L

M

N

A code ID character identifies the code type of a scanned bar code. This may be useful when the scanner is decoding more than one code type. In addition to any single character prefix already selected, the code

ID character is inserted between the prefix and the decoded symbol. The user may select no code ID character, a Symbol Code ID character, or an AIM Code ID character. The Symbol Code ID characters are listed below.

UPC-A, UPC-E, UPC-E1, EAN-8, EAN-13

Code 39, Code 32

Code 93

Interleaved 2 of 5

MSI Plessey

UCC/EAN-128

Bookland EAN

Coupon Code

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

42

����������

Prefix/Suffix Values

A prefix and/or one or two suffixes may be appended to scan data for use in data editing. These values are set by scanning a four digit number (i.e. four bar codes) that correspond to terminal’s key codes. See

Numeric Bar Codes on page 46. If you make an error, or wish to change your selection, scan the CANCEL bar code on page 47. (Note: In order to use Prefix/Suffix values, the Scan Data Transmission Format must be set. See next page).

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

43

����������

Scan Data Transmission Format

To change the Scan Data Transmission Format, scan one of the eight bar codes below or on the following pages corresponding to the desired format.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

44

����������

Scan Angle

Choose one of the options below to adjust the visible scan width in scanners that support laser clipping.

The scan width is reduced by software control.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

45

����������

Numeric Bar Codes

For parameters requiring specific numeric values, scan the appropriately numbered bar code(s).

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

46

����������

CANCEL

If you make an error, or wish to change your selection, scan the bar code below.

©2005 Nordic ID Oy

Laser Scanner Programming Guide (SE923 laser engine), rev 1, August 1st 2005

47

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement