CFR Perfect Heat Pro 500 Series Instruction manual

CFR Perfect Heat Pro 500 Series helps you achieve professional-grade cleaning results. With its Perfect Heat system, this machine provides heated cleaning solution up to 200 degrees Fahrenheit, enhancing the cleaning power and ensuring faster drying times. Ideal for commercial use, it features a powerful vacuum motor for effective dirt and water removal. Maintain a clean and healthy environment with ease using the CFR Perfect Heat Pro 500 Series.

PDF Download

Document

Perfect Heat, Pro 500 and Pro 750 Series

INSTRUCTION MANUAL

Read all instructions before using this machine.

IMPORTANT SAFETY INSTRUCTIONS

This manual is to ensure that the CFR Pro Series is operated correctly.

All operators must read, understand and practice the following safety instructions.

72671A 01/2005

Introduction . . . . . . . . . . . . . . . . . . . . . . . . .2

Unpacking instructions . . . . . . . . . . . . . . . .3

Safety instructions . . . . . . . . . . . . . . . . . . . .3

Preparing for cleaning . . . . . . . . . . . . . . . . .4

Operating instructions . . . . . . . . . . . . . . . . .4

Maintenance . . . . . . . . . . . . . . . . . . . . . . . .5

Parts and drawings . . . . . . . . . . . . . . . . . . .8

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . .12

UNPACKING INSTRUCTIONS

Your Pro 500/750 was thoroughly inspected, tested, and packaged to deliver the equipment in good operating condition. The freight carrier received and signed for the equipment in good condition. Damage can occur during shipping and to protect your interest, all cartons must be inspected for damage (including any concealed damage) that might have occurred during shipment. Any damage is the responsibility of the freight carrier and should be reported immediately to the carrier. It is your responsibility to issue a claim and to receive compensation from the freight carrier for any damage done in transit. Shipping damage is not warranted.

INTRODUCTION

Congratulations on your purchase of a CFR Pro 500/750.

Read this entire manual before operating or servicing the .

CAUTION

Please complete and return the enclosed warranty card.

Read All Instructions, Warnings and Cautions

Before Using

Parts and Service

The Paramount is covered by CFR’s Preventative

Maintenance Program which is designed to maintain the

Paramount on a quarterly basis. The program focuses on: inspecting the equipment, replacing covered parts as required, and identifying potential situations where a more in-depth service or training may be required.

If service is required, it must be performed by an authorized

CFR repair center. Contact your local dealer or call

1.800.533.2557 for the location of a repair center.

These guidelines are provided for your protection and convenience. Please read them carefully. If you have any questions regarding the use of your equipment call CFR

Technical Service at 800.533.2557 Failure to adhere to instructions provided can potentially void any warranties.

Precautions and safety warnings are provided for your protection Failure to observe these warnings could result in personal injury and damage to the equipment. When using an electrical appliance, basic safety precautions should always be followed.

Serial Number

The serial number of the machine is located on the nameplate, located next to power switch. This information is needed when ordering parts or scheduling repairs. Fill in the information below for future reference:

WARNING!

To avoid fire, do not use with a flammable or combustible liquid to clean floor.

Serial Number ___________________________________________________________________

Part Number _ ____________________________________________________________________

Purchase Date _________________________________________________________________

IMPORTANT SAFETY INSTRUCTIONS

The Pro 500/750 is intended for use only as described in this manual. Using the equipment in any manner not described in this manual can void the warranty. Use only manufacturer’s recommended accessories.

READ ALL INSTRUCTIONS BEFORE USING

THIS PRODUCT IS INTENDED FOR

COMMERCIAL USE ONLY

When using a electrical piece of equipment basic precautions should be followed, including the following:

CFR PRO SERIES

WARNING! To reduce the risk of electric shock, fire, or injury:

Operators must read and understand this manual completely before operating the equipment.

Make sure all caution, warning, and instructional decals are in place and legible. Replace damaged or missing labels.

Do not leave unit when plugged in. Unplug from outlet when not in use and before servicing.

Connect to a proper grounded outlet only.

(See Grounding Instructions.)

Do not use with damaged cord or plug.

Do not handle plug or unit with wet hands.

Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.

Turn off all controls before unplugging.

Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

10. Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.

11. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

12. Do not use without filters in place.

13. Use extra care when cleaning stairs.

14. Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present.

15. Do not expose to rain. Store indoors.

16. If unit is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, take it to a local CFR service center.

WARNING! Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance – if it will not fit the outlet; have a grounded outlet installed by a qualified electrician.

SET UP INSTRUCTION

Filter Installation

There are three filters in the Pro 500/750: inlet filter, main filter and pump protection filter. It is imperative to the efficient operation of the Pro 500/750 that the filters are installed properly.

Pump Protection Filter – Position on brass fitting on the filter mound. Slide it down.

Main Filter – Wet the rim of the filter and position it on the filter mound. (white plastic disc) Twist and slide over the mound by pushing downward.

Inlet Filter – Position on top of the tank.

GROUNDING INSTRUCTIONS

This unit must be grounded. Grounding provides the path of least resistance for electric current, in the event of malfunction or breakdown, to reduce the risk of electric shock.

This unit is equipped with a cord having an equipmentgrounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

OPERATING INSTRUCTIONS

Remove lid and inlet filter.

Check main filter. Make sure the main filter is installed snugly.

Fill tank with water to a desired level. Use solution level gauge.Maximum water temperature to be used is 120 to 130 degrees F.

Add CFR in-tank cleaner per chemical label use instructions. In addition, pre-spraying is often desirable and will assist in producing the fastest and best cleaning results. See chemical product labels for more information. Note: Use caution when moving machine

(especially on inclines) with fluid in the tank to prevent fluid from entering vacuum standpipe at back of machine tank and flooding the vacuum.

CFR chemicals have been speically formulated to work with this machine.

Prime pump by re-circulating fluid through priming hose included for 15/30 seconds. Re-circulating the fluid primes the pump and expels trapped air from the system.

Replace inlet filter and lid

Attach hose assembly to machine. Connect fluid hose to the quick-disconnect found on the front of machine.

Attach the desired tool to the valve end of the hose assembly.

Close tank cover lid, turn on vacuum and pump switches.

CFR PRO SERIES

10. Clean surface with tool attached to hose assembly.

11. During the cleaning process, the fluid level will be reduced and the lower level float switch will shut off the pump. When the pump shuts off, drain and rinse tank, rinse main filter, refill with fresh water and cleaning chemical, and continue cleaning.

Perfect Heat System

WARNING! The Perfect Heat TM Plus System can produce very hot water that could damage some delicate fabrics and fibers. Please ensure the surface being cleaned will not be damaged by hot water up to 200 degrees Fahrenheit.

CAUTION! When cleaning, monitor foam in the machine's tank. Areas cleaned with other cleaning equipment or chemicals may cause excessive foam to collect in the tank.

This machine is equiped with the Perfect Heat TM Plus System for heating the cleaning solution. This system uses a combination of the patent pending Perfect Heat TM cal heater.

coils and an inline electri-

WARNING! EXCESSIVE FOAM IN THE

TANK MAY CAUSE VACUUM MOTOR FLOODING AND

MACHINE DAMAGE. Pour one to two ounces of CFR

Defoam directly into the tank or into the vacuum hose while the vacuum is running. CFR Defoamer has

been speically formulated to work with this machine.

Operation:

1. Follow operating instructions steps for filling the machine with water and cleaning solution.

2. Turn on electrical heater, switch is located on panel.

3. Pre-heat machine for 5-10 minutes before use.

When finished cleaning, perform the daily maintenance procedure. Be sure that all filters are cleaned thoroughly and replaced in machine. Leave lid off for drying.

NOTE: There is a valve in the upper compartment that either

sends the water through the heating components, or bypasses them. The machine is preset in the “HOT” position. To clean with cold water, turn the valve to “COLD” or UP position. This should be done prior to filling the tank with water. For general cleaning, it is recommended leaving the valve in the “HOT” or down position and cleaning with hot water.

inlet filter main filter drain hose valve pump filter switch panel

CFR PRO SERIES

MAINTENANCE

Daily Maintenance

To maintain optimum performance the equipment, tools and filters should be cleaned after each use. Replace any filters that cannot be cleaned or are damaged. Nozzles that cannot be cleared should be discarded. Wipe down the equipment with a damp cloth to keep clean and preserve the appearance.

Wands and Tools

Rinse opening of tool with water to eliminate any debris.

Wand only – open and clean in-line strainer.

A. Disconnect the In-line Strainer by using the quick disconnect coupler.

B. Remove the filter and rinse with water.

C. Remove any debris from the strainer.

D. Keep o-ring and threads of the plug lubricated.

CFR DEFOAM is a good lubricant or use a non-petroleum based lubricant. This will ensure a tighter seal.

Wipe tool with damp cloth and store with head up to prevent clogging of nozzle.

Periodic Maintenance

Check power cord for any breaks, separations, or cuts.

Make sure the ground pin on the connector is intact or the machine will be unsafe. Make sure the ground pin on all three prongs on the twist lock connector are intact.

Check for plugged nozzles when using tools. If streaking occurs during cleaning, a plugged nozzle may be the cause. A plugged or partially plugged nozzle can be identified by holding the tool 5-7" above the surface and checking for an even spray pattern.

To clean a plugged nozzle, remove the nozzle and direct pressurized air backwards through the nozzle or backwash the nozzle with water. A convenient method is to insert the nozzle into a garden hose ball valve, tighten the ball valve to a faucet, and turn on the water. (CFR has ball valves available, part #7AX020).

Inspect nozzle and repeat cleaning procedure, if necessary. Discard nozzles that cannot be cleared.

Tool nozzles wear and must be replaced after 200-250 hours of use.

Occasionally open the base and inspect hose and other connections for leaks. Repair or replace any leaking parts. Always disconnect power cord, before removing side panels.

Periodic Maintenance

It is very important to monitor machine operating hours for proper maintenance of the motors and pumps. After

700 hours of operation, the vacuum motor brushes should be inspected by an authorized repair station and replaced if worn (length is .5 inches or less).

Filters

In-Line Strainer Filter – Disconnect the In-line Strainer

Filter on the wand by using the quick disconnect coupler. Remove the filter and rinse with water.

Remove any debris from the strainer. Keep o-ring and threads of the plug lubricated. CFR DeFoam is a good lubricant or use a non-petroleum based lubricant.

This will ensure a tighter seal.

Inlet Filter – Remove the inlet filter. Dump and clean debris at the end of each cleaning job.

Main Filter – Remove the main filter sleeve and rinse out and clean thoroughly.

Check vacuum motor performance using a vacuum gauge. Place this gauge on the tank inlet fitting with the vacuum turned on. Water lift should be between

135 and 150 inches. If the reading is lower, check for air leaks in the tank, cover gasket, and drain hose.

Check pump performance occasionally against built-in pressure gauge. Pump running pressure on the Pro

500 should be 500 + 10 p.s.i, Pro 750 should be 750+

15 p.s.i. If the pumping pressure is outside of this range, call your dealer or authorized station. After 400 hours, the pump valves should be replaced. After 700 hours of operation the pump cam bearing and plunger should be replaced. The pressure regulator should be rebuilt after 400 hours of operation.

Pump Protection Filter – This ball-shaped filter should be in place when the tank is cleaned and rinsed. Remove and rinse only after the tank is rinsed.

CFR PRO SERIES

tank inlet pressure guage pump vac motor

SPECIFICATIONS - Pro 500

Power Cord . . . . . . . . . . . . . . One Cord, 12 Ga, 3 Wire, Molded End

Plug

Voltage . . . . . . . . . . . . . . . . . . 115/120 volts AC, 60 HZ

Vacuum Motor . . . . . . . . . . . . 1’ amps

Pump Motor . . . . . . . . . . . . . . 3 amps

Tank Volume. . . . . . . . . . . . . . 15 gallons max

Fill Level . . . . . . . . . . . . . . . . . 1” below the bottom of the Inlet filter.

Vacuum Motor . . . . . . . . . . . . (2) 2 stage with150" water lift

Pump Motor . . . . . . . . . . . . . . 1/2 hp AC motor

Pump . . . . . . . . . . . . . . . . . . . plunger type; 0 to 500 psi.

Weight . . . . . . . . . . . . . . . . . . 124 lbs.

Height . . . . . . . . . . . . . . . . . . . 41"

Width . . . . . . . . . . . . . . . . . . . 29"

Length. . . . . . . . . . . . . . . . . . . 22"

Wheels . . . . . . . . . . . . . . . . . . non-marking wheels

Casters . . . . . . . . . . . . . . . . . . non-marking wheels

Body . . . . . . . . . . . . . . . . . . . . rotomolded polyethelene

Filters . . . . . . . . . . . . . . . . . . .three filters: inlet filter, main filter, and pump protection filter.

Circuit Breakers: Overload circuit breakers are placed in both the pump and vacuum circuits to protect against unusually heavy current

(ampere) loads. If either breaker trips, the pump motor or vacuum motor is overloaded.

SPECIFICATIONS – Pro 750

Power Cord . . . . . . . . . . . . . .One Cord, 12 Ga, 3 Wire, Molded End

Plug

Voltage . . . . . . . . . . . . . . . . . .115/120 volts AC, 60 HZ

Vacuum Motor . . . . . . . . . . . .5.4 amps

Pump Motor . . . . . . . . . . . . . .3 amps

Tank Volume . . . . . . . . . . . . .15 gallons max

Fill Level . . . . . . . . . . . . . . . . .1” below the bottom of the Inlet filter.

Vacuum Motor . . . . . . . . . . . .3 stage with135" of maximum water lift

Pump Motor . . . . . . . . . . . . . .1/2 hp AC motor

Pump . . . . . . . . . . . . . . . . . . .plunger type; 0 to 750 psi.

Weight . . . . . . . . . . . . . . . . . .128 lbs.

Height . . . . . . . . . . . . . . . . . . .41"

Width . . . . . . . . . . . . . . . . . . .29"

Length . . . . . . . . . . . . . . . . . .22"

Wheels . . . . . . . . . . . . . . . . . .non-marking wheels

Casters . . . . . . . . . . . . . . . . . .non-marking wheels

Body . . . . . . . . . . . . . . . . . . . .rotomolded polyethelene

Filters . . . . . . . . . . . . . . . . . . three filters: inlet filter, main filter, and pump protection filter.

Circuit Breakers: Overload circuit breakers are placed in both the pump and vacuum circuits to protect against unusually heavy current

(ampere) loads. If either breaker trips, the pump motor or vacuum motor is overloaded.

CFR PRO SERIES

TROUBLE SHOOTING GUIDE

Vacuum or pump will not run Check that electrical cord is firmly seated in wall outlet.

Check and reset building circuit breaker if tripped.

Check vacuum/pump switch. It should be in the “on” position.

Trips building circuit breaker

Vacuum won’t run.

Pump won’t run

Pump tries to run and then blows circuit breaker

Pump starts and stops

Water dripping from bottom of machine exhaust.

Vacuum hose or tool leaks.

Carpet too wet.

Streaks on carpet.

Circuit is overloaded – move cord to a different wall outlet.

If using an additional extension cord, make sure it is in good condition, less than 70 feet long and #10 gauge or heavier.

Check plug end and cord for damage.

Check vacuum switch. It should be in the “on” position.

Check fuses and replace if tripped. (located on base of machine)

Check pump switch – it should be in the “on” position.

Check pump circuit breaker (5 amp) and reset if tripped.

Check fluid level, must have at least 5 gallons in tank.

Check fluid level inside of Main Filter Cage – pump float must be at highest position to operate.

If fluid is lower inside filter, drain tank and remove and clean filter.

Check power cord for frayed, cut or worn spots.

If using an extension cord,make sure it is in good condition, less than 70 feet long and #10 gauge or heavier.

Check pump static PSI – must be 400 psi or less

Check wall outlet voltage. If below 105 volts, pump will not work.

Check for dirty Main Filter. Water level should be the same inside and outside of filter.

Check for sticking pump float.

Check fluid level – must have at least 5 gallons in tank.

Check machine for excess foaming. Add CFR Defoam to tool hose and tank. Open machine top cover and let vacuum run for 10 minutes to dry out vacuum motor, then close lid and resume cleaning.

Leave vacuum running for 1 minute when finished cleaning to clear hose.

Check for holes/breaks in vacuum hose.

Make sure the inline strainer is properly tightened and fluid hose connectors are fully seated.

NOTE: CFR floor tool is used in forward direction only.

Check carpet tool position – head must be completely “seated” on carpet to provide good drying times.

Check tool and hose for any obstructions.

Check lid cover sealing properly – is filter case properly seated in tank? Is lid gasket in good shape with no cuts, cracks, or worn/compressed areas?

Check for cracks in lid cover.

Check drain hose and fittings for cracks and tears.

Check tool hose for holes, cracks, or cuts.

Check hose cuffs – must seat firmly on tank fitting and tool.

Check water dripping from bottom of machine exhaust. If present, check machine for excess foaming.

Check carpet installation. Some carpets are installed on uneven surfaces with ridges and bumps. It is difficult to get good drying times with this type of installation.

Check tool and hose for obstructions.

Check and clean inline strainer filter.

Check and clean main filter.

Check and clean stainless back flush filter screen inside tank.

Check nozzles for full spray. Clean if clogged or replace if worn.

Check pump pressure drop while cleaning. Should not drop more than 100 p.s.i. Make sure air is out of system by re-priming pump. If there is still a problem, remove and clean back flush filter screen.

Make sure strokes overlap a minimum of 3 inches.

Check CFR chemical usage instructions for proper application.

Multiple cleanings may be needed to clean deeply imbedded dirt that is pulled to the surface by CFR’s deep cleaning technology. Offset cleaning passes by 6 inches.

Excessive pressure drop when cleaning.

(exceeds 100 p.s.i.)

Adjust static pressure to 500/750 p.s.i. when not cleaning.

Check and clean main filter and inner stainless back flush filter.

Check and replace worn spray nozzles and loose or leaking fittings on hose.

Purge excess air from pumping system using hose with no nozzle or priming hose.

CFR PRO SERIES

Base Assembly

CFR PRO SERIES

Base Assembly

Ref # Part #

72620AM

72633A

X9066+

7GL002

7CM007

72635A

72640A

72623A

7CW002

X9204+

72000A

72651A

70020B

1942-C

72365A

72611A

7BF003

7CM003

72624A

72630A

72641A

72662A

72638A

72636A

72388A

PX65

7DT001

X8851

72639A

7BF008

X8239

PX6

7CX002

7AV001

72642A

72625A

7DL003

71521A

X9069

X8848

7GF033

72667A

72643A

72644A

71644A

70079C

7DL008

X8235

7EW001

7BS003

X9014

72020A

PF1750

PF1750-2

Description

Base, PFX1350, Maroon

Axle, 23.375” Long

Wheel, 12” x 1.75” Non-Marking

Push Nut, 1/ 2”

Washer, 1/ 2 USS Flat, 18-8 SS

Spacer, 1/ 2” ID x 3/ 4” OD x 1/ 4” Long

Gasket, Vac Manifold, Long

Cover, Vacuum manifold

Screw, #6 x 3 /4 Phil Pan TS, Type A 18-8 SS

Rod, 10-24, “T” Bolt

Rod, 3/16 x 5-1/2, All Thread Stud, 18-8 SS

Spacer, VAC Motor, 2.375”

Gasket, Vacuum Motor Seal

Vacuum Motor, 115VAC, 2 – satage

Vacuum Motor, 3 stage, 120V For Pro 750

Vacuum Motor, 3 stage, 230V, 5.7IN

Nut, Kep, #10-24 Zinc

Washer, #10 USS Flat, 18-8 SS

Cover, Vacuum manifold, Shor

Cover, Vacuum manifold, Flat

Gasket, Vac manifold, Short

Screw, #10 x 1/ 2”, Flat Phill SM, Black

Pressure regulator plate

Cover Plate, Bottom

Screw, #10 x 5/8, Tap phil, SS pan Head

Caster, 4” Black

Screw, 5/16-18 x 5/8, Hex Tap Zinc

Screw, 10-32 x 1’ Phil, Pan MS, Black, Zinc

Gasket, mounting pressure regulator

Nut, kep, 10-32 Zinc

Washer, 1/ 2 USS Flat Zinc

1/ 4 x 1/ 4 Female Quick disconnect, Brass

Nipple, Hex 1/ 4 MPT

Tee, Union, 1/ 4 NPT

Gasket, Vac manifold, Circle

Cover, Vacuum manifold, Circle

Clamp, Hose 1/ 4”

Tee, barb, 1/ 2” x 1/ 2”

End Loop, SS, w / 2 holes, 16G

Jacknut, 1/ 4 -20 Steel, #8 LJN

Pad, Motor mount

Washer, Rubber, 29 ID, .688OD, .093THK

Pump Assembly, 500 PSI

Pump Assembly, 750 PSI, .140 CAM

Screw, #10 x 1 Phil Pan TS, 18-8 SS

Hose, 1/ 4” Wire Reinforced

Clamp, 1/ 4” Worm Gear, SS, Hex Slot, Phil HD

Washer, 1 /4 Flat USS Zinc

Screw, 1 /4-20 x 3/ 4” Phil pan MS SS

Screw, 1 /4-20 x 1 /2, Phil, pan, MS 18-8 SS

Hinge

Screw, #12 x 1”, Self tap, PHMS, Zinc

Heater Unit, 1750 Watts

Heater unit, 220V

Ref # Part #

PX212

PD8

7FC010

71653A

72710B

X9173

72411A

71544A

72387A

PX112

72632B

72715A

X8008N

71379A

71379B

72684A

72665A

72661A

71952A

71953A

71716AP

72698A

X9179

71775A

7GG003

71570A

71810A

71629A

71999A

72702A

72699A

72718A

75 72700A

72701A

72703A

71743A

7CY006

X8260+

71804A

72142A

X8256

X8254

PC66

71130A

70101A

72713A

72713B

X8244

7AT003

PC38

72726A

SW158

7BF030

Description

Fitting, Brass, 90 degree elbow, 1 /4 NPTM

Strain Relief, 1/ 2” NPT

Circuit Breaker, 8A

Circuit Breaker, 10A

Circuit Breaker magnetic, 5A

Hole plug, Switch Hole

Hour meter, AC

Hour meter, 230V

Screw, #8 x 5/8, Black, Tap Phil, Pan Head

Pigtail, Black, 12/3 SJT x 39” Long

Switch Panel, With fan

Switch Panel, Perfect Heat (no fan)

Nut, Lock, 1 /2” Steel Conduit

Relay, 25A, 120V

Relay, 240V

Screw, 1 /4-20 x 2-1/2 Phil, Pan

Insert, Tee Nut, 1 /4 -20 Thread

Wand Holder

Convertor Kit, OZ Long

Convertor Kit, OZ Long, 230V carbon Filter

Cover, Carbon Filter, Pro Series

Pump motor, 100 PSI, 115V

Elbow, 1 /2” Hose x 3/8” NPT, 90deg Plastic

Hose A/S Braided

Injector, ozone

Hose, Clear, tygon, 1/8” ID x 1 /4” OD

O-ring, Shaft end pulley

Barb Hose, 1/2H

Cover, Fan

Foam, Switch panel

Foam, Switch Panel , Pro 400

Fan, Cooling, 115V, 92mm, 35CFM

Fan, Cooling, 230V, 92mm, 50CFM

Screw, 8-32 x 2” L, phil, Pan MS, Zinc

Screw, 8-32 x3/16” PHMS

Washer #8 Internal Tooth Lock, 18-8 SS

Nut, 8-32 Lock w/ Nylon Insert

Plug, 1 /2” Hole, Black Nylon

Plug, 7/8” black nylon

Mut, 8-32, keps, Zinc

Hose, Solution, 1 /4” Id, 400 PSI

Fitting, Brass, 1/8 NPTM x 1 /4 Barb Hose

Coupler QD, 1/8 M

Nipple, QD, 1/8F, Brass

Heater Coil, 2- stage vacuum

Heater Coil, 3- stage Vacuum

Screw, 1—24 x 2”, Phil, Pan MS, Zinc

Barb, Hose, 1/4H – 1/4M

Connector, Double thread, female

Valve, 3-way

1 /4” Cable Clamp

Nut, 10-24, Nylon Insert Lock, 18-8 SS

CFR PRO SERIES

Tank Assembly

CFR PRO SERIES

Tank Assembly

Ref # Part #

72619A

PX25+

X9014+

7BS003

71644A

71920A

72388A

72631A

72666A

PX14A+

72173A

72224B

72326A

72323B

72321A

7DE016

71576A

71495A

7AT006

71817A

7DL003

71897A

7DL008

70079C

PC25+

7AF003

Description

Tank, Recycling

Fitting, Plastic, 1- ?” NPT x 1- ?” Hose Barb

Tank Hinge

Screw, ?-20 x 1/2” Phil Pan MS 18-8 SS

Screw, #10 x 1” Phil Pan TS

Ring Washer

Screw, #10 x 5/8, Tapping Phil, SS Pan Head 4

Latch Bracket 2

Inlet Fitting, Short 1

Dump Valve Gasket 1- ?”, 2.5 OD x 1.75 Rubber2

Spring Clip, Black Vinyl Coated

Main Filter, New, Smaller

Filter, Inlet

Gasket, Lid 43”

Qty

Lid, Tank

Nozzle H 1/8 VV CH SS 11001

Nipple QD 1/8 M SS

Pump Protection Filter

Barb Elbow, 90°, ?-1/8

Hose, ?” Braided

Hose Clamp, ?”

Gasket, Filter Mount

Hose Clamp, ?” SS

Hose, ? Wire Reinforced

?” to ?” Male/Male Barb

Plug, Counter Hex ?”

22”

42”

Ref # Part #

72317A

70343A

71553A

70100A

7CX001

SW139+

71485A

72628A

PX63+

X8235+

72486A

7DL005

PAS37+

PAS36+

72645A

X8025+

7BH004

72656A

72476A

72598A

72589A

72659A

72588A

50 72660A

Description

Filter Mount

Switch Float 2 Pole

E-Ring, Float Switch 70143A

Coupler QD 1/8F

Nipple Hex 1/8

Elbow, 1/8 Street (90 degree)

Header Backflush Nozzle

Vacuum Standpipe, New Pro

Coupler, Plastic, 1- ?” Slip

Washer, ?” Flat, USS Zinc

Spacer, 1.625 Long, .50 OD, .313 ID

Clamp Worm Gear 1-1/2 SS

Drain Hose

Expansion Plug Drain

Bolt, 5/16-18 x 2-1/4, Hex

Wheel, Black, 4” x 1-1/4”

Screw, 10-32 x 3/8” Phil Pan 18-8 SS

Hose, 1-1/2” Wire-Reinforced, Black

32”

Fitting, Nylon Hose Barb, 1-1/4” ID, 1-1/2” NPT 1

Screw, 1/4-20 x 3/4” Phil Flat, SS 1

White Delrin Hollow Rod, 1/2" OD, 1/4" ID, 7” Long

Qty

Decal, Water Level Gauge

Heat Shrink Tubing, Clear PVC,

5/8” Exp. ID, 7.5”L1

Rope

26”

CFR PRO SERIES

Warranty

CFR, a Tacony company, warrants new products manufactured and sold under the name CFR to be free from defects in materials and workmanship under normal use and service. CFR’s obligation under this warranty is limited to repairing or replacing, at our option, such products or parts which are returned to our factory authorized service center, freight prepaid, within the warranty period and are found to be defective in materials or workmanship. For rotationally molded polyethylene housings and aluminum frames and chassis this warranty expires 60 months from the date of registration; if the warrant is not registered, it expires 60 months from the factory shipment date. For all other components, with the exception of wear items (i.e. filter, nozzles, etc.) this warranty expires 12 months from the date of registration on the warranty.

If not registered, is expires 12 months from the factory shipment date. For hoses, tools, and other attachments manufactured and sold by CFR, this warranty expires 12 months form factory shipment date. Parts replaced or repaired under warranty are guaranteed for the remainder of the original warranty period. Replacement parts that have become defective through wear or abuse are not included in this warranty. CFR will pay service labor to the distributor or authorized service repair center per the warranty flat rate schedule. Service labor will be paid for two years on all warranted polyethylene housings, aluminum frames and chassis, and one year on all other warranted components.

CFR systems are designed for use only with specially formulated CFR Recyclable Cleaning Chemicals. Use of any other chemical in CFR systems may cause damage to the pump, motor and other components and may void the warranty.

This warranty shall cease to be in effect if repairs, replacements or alternations are made by the purchaser or any nonauthorized service station. This warranty does not apply to damage caused by misuse, abuse, or negligence of the buyer or third party, or damage due to transportation of product.

CFR MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATIONS, ANY WARRANTIES OF

FITNESS OR MERCHANTABILITY, EXCEPT AS EXPRESSLY SET FORTH ABOVE WITH RESPECT TO SUCH PROD-

UCTS OR PARTS THEREIN. NOR SHALL CFR HAVE INCURRED ANY OTHER OBLIGATIONS OR LIABILITIES ON

ITS PART OR BE LIABLE FOR ANY ANTICIPATED OR LOST PROFITS, INCIDENTAL DAMAGES, CONSEQUENTIAL

DAMAGES, TIME CHARGES OR ANY OTHER LOSSES INCURRED IN CONNECTION WITH THE PURCHASE,

INSTALLATION, REPLACEMENT OR REPAIR OF SUCH PRODUCTS OR ANY PARTS THEREIN WHETHER ORIGI-

NAL EQUIPMENT OR INSTALLED AS A REPLACEMENT, COVERED BY THIS WARRANTY OR OTHERWISE; AND

CFR DOES NOT AUTHORIZE ANY PERSONA TO ASSUME FOR CFR ANY OTHER LIABILITY IN CONNECTION

WITH THE PRODUCTS OR PARTS THEREIN.

For more information about top quality CFR products please see your local CFR distributor or visit us at www.CFRcorp.com

Thank you for purchasing

CFR Cleaning Systems.

3101 Wichita Court ■ Fort Worth, TX 76140 ■ 800.533.2557 ■ www.CFRcorp.com

72671A 01/2005

Hello! I am an AI chatbot specifically trained to assist you with the CFR Perfect Heat Pro 500 Series Instruction manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant terminated