Whalen XLGTD-8 XLGTD-8 Gaming Theater™ Console User manual

LOT NUMBER:

DATE PURCHASED: / /

3-in-1 Gaming Theater

TM

Console with Storage Drawer

Model # WMCXLGTD-8

This item is designed to be a 3-in-1 configuration. Please choose the option that best suits your needs. DO NOT discard any of the hardware or parts that you will not use on your set option. This will give you the opportunity to use this TV Stand for different configurations in case you decide to upgrade your TV set in the future.

ADULT ASSEMBLY REQUIRED

If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our toll-free customer service number and have your instructions and parts list ready to provide the model name, part name or factory number:

1-866-942-5362 8:30 a.m. - 4:30 p.m

., PST, Monday - Friday

ONLINE: www.whalenstyle.com

EMAIL: [email protected]

On-line Video Instruction Guides

Go to http://whalen.showuhow.com to view step-by-step instructional videos for assembling and installing your product. Enter the following product number on the ShowUhow homepage.

WMCXLGTD-8

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE

READ AND KEEP FOR FUTURE REFERENCE.

Whalen Furniture Mfg., Inc. Page 1 Factory # 11906

M A X I M U M R E C O M M E N D E D W E I G H T L O A D S

MANUFACTURER: Whalen Furniture

CATALOG: 3-in-1 Gaming Theater

TM

Console with Storage Drawer (WMCXLGTD-8)

DATE OF MANUFACTURE: March 2012

MADE IN CHINA

MAXIMUM LOAD 15 lb. (6.8 kg)

FITS UP TO MOST 60 ” FLAT PANEL TVs


FITS UP TO MOST 60

” FLAT PANEL TVs

WITHOUT SWIVELING BRACKET


PLACE TV BEHIND THE STOPPER



THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH

FLAT PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND

WEIGHT LIMITS. NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT

PANEL TVS OR EQUIPMENT. TO AVOID INSTABILITY, PLACE FLAT PANEL TV IN CENTRE

OF UNIT; CRT TVS, IMPROPERLY POSITIONED FLAT PANEL TVS, OR FLAT PANEL TVS OR

OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND WEIGHT LIMITS COULD

FALL OFF OR BREAK THE UNIT, CAUSING POSSIBLE SERIOUS INJURY.

G E N E R A L I N F O R M A T I O N , T I P S a n d T R I C K S

1. Please read the Assembly Instructions prior to assembling this product.

2. Remove all hardware from box and sort by size.

3. Check to see that all hardware and parts are present BEFORE assembling.

4. Ask a friend to assist you with the assembly of this furniture.

5. To avoid damage, assemble the product on a sturdy, level and protective surface.

6. Please wait until all steps are completed before tightening bolts.

7. Make sure all bolts are tightly fastened before the unit is used.

This product is sold with Tip Restraint Hardware kit. You must install the Tipping Restraint

Hardware between the wall and the TV stand to prevent any accidents or damages. When properly installed, this restraint can provide protection against the unexpected tipping of the unit due to small tremors, bumps or climbing. The restraint is only a deterrent and is not a substitute for proper adult supervision. Use of tip-over restraints may only reduce, but not eliminate, the risk of tip-over.

Please call for replacement parts or assistance: 1-866-942-5362


Parts and Hardware List

Please read completely through the instructions and verify that all parts listed are present before beginning assembly.

A- TOP SHELF FRAME (1) B- MIDDLE UPPER METAL FRAME (1) C- BOTTOM SHELF FRAME (1)

D- LONG SPINE (1) D1- SHORT SPINE (1) E- LEFT SIDE FRAME (1)

F- RIGHT SIDE FRAME (1) G- LEFT SIDE PANEL (1) H- RIGHT SIDE PANEL (1)

I- DIVIDER PANEL (1) J- LEFT LEG (1) K- RIGHT LEG (1)

L- TOP GLASS (1) M- GLASS SHELF (2) N- SWIVELING BRACKET (1)

PL

PR

O- XYZ MOUNTING FRAME (1) P- MONITOR BRACKET (2) Q- SSS SPINE (1)





R- SENSOR/SOUND SHELF (1) S- LEFT DRAWER FRONT (1) T- RIGHT DRAWER FRONT (1)

U- DRAWER BACK (2) V- DRAWER LEFT SIDE (2) W- DRAWER RIGHT SIDE (2)

X- DRAWER BOTTOM Y- DRAWER BOTTOM SUPPORT Z- SPINE DECORATIVE PANEL

(2) (2) (1)

AA- ADJUSTABLE SHELF FRAME (1) BB- GAMING GUITAR CLIP (1) CC- CABLE WHEEL (2)

(1) SUCTION CUP (2) 1/2 ” BOLT (3) 5/8” BOLT (4) 1” BOLT

(7+1 extra) (8+1 extra) (33+1 extra) (14+1 extra)

(5) 1-5/8 ” BOLT

(6+1 extra)

(6) LOCK WASHER (7) FLAT WASHER (8) LARGE FLAT WASHER

(50+2 extra) (50+2 extra) (4+1 extra)





(9) 2-1/2

” LAG BOLT

(10) CONCRETE ANCHOR (11) GLASS BUMPER

(4) (4) (11+1 extra)

(12) PLASTIC HOUSING (13) HANDLE w/BOLTS

(8) (2)

(14) ACRYLIC STOPPER

(1)

M4 ALLEN WRENCH 3/16 ” ALLEN WRENCH TOUCH-UP PEN TIPPING RESTRAINT HARDWARE KIT (1)

(2) (1) (1) (Inside Plastic Bag)

TV Mounting Kit

M4 x 12 BOLT (4) M4 x 30 BOLT (4) M5 x 12 BOLT (4) M5 x 30 BOLT (4)

M6 x 12 BOLT (4) M6 x 35 BOLT (4) M8 x 16 BOLT (4) M8 x 40 BOLT (4)

M4 LOCK WASHER (4) M5 LOCK WASHER (4) M6 LOCK WASHER (4) M8 LOCK WASHER (4)

LARGE SPACER (4) SMALL SPACER (4) M4/M5 FLAT WASHER (8) M6/M8 FLAT WASHER (4)

Tools required: Allen Wrench (provided) and Phillips Screwdriver (not provided).



Drawer Assembling

V/W

PLASTIC HOUSING

(2 used in this step)

U

⑫

12

V/W

U

U

1. Unpack the unit and confirm that you have all the hardware and required parts listed.

2. Locate a DRAWER BACK (U) on a flat and protected surface with the groove facing up.

Connect one DRAWER RIGHT SIDE (W) to the DRAWER BACK (U) by inserting one PLASTIC

HOUSING (12) all the way onto the corner PLASTIC JOINTS.

NOTE: Using the end wood dowels for easy alignment. Make sure the grooves line up with each other.

3. Repeat last step to connect one DRAWER LEFT SIDE (V) to the DRAWER BACK (U) at the other end.




Y

U

4. Align and attach the DRAWER BOTTOM SUPPORT (Y) to the DRAWER BACK (U) by engaging the PLASTIC FITTING.

NOTE: Turn the Lever if necessary when aligning the PLASTIC FITTING. Once the latch of

PLASTIC FITTING is connected inside Socket, push the Lever all the way to the side with cutout to connect them together.

5. Slide the DRAWER BOTTOM (X) into the grooves in the DRAWER SIDES and DRAWER

BACK. Ensure the unfinished surface of DRAWER BOTTOM will face floor.




S/T

Y

6. Align and attach one DRAWER FRONT (S or T) to the other end of DRAWER BOTTOM

SUPPORT (Y) by engaging the PLASTIC FITTING. Make sure that DRAWER BOTTOM (X) fits securely into the groove of the DRAWER FRONT as shown above.




S/T

PLASTIC HOUSING


⑫

13

S/T

12

S/T

HANDLE AND BOLTS


⑬

U/V

7. Align and insert two PLASTIC HOUSINGS (12) all the way onto the corner PLASTIC JOINTS to secure the DRAWER FRONT in place.

8. Remove the bolts in one HANDLE (13), then use the bolts to attach the HANDLE to the outside of DRAWER FRONT (S or T).

9. Repeat the process to assemble the other drawer.



Assembly Instructions

5/8” BOLT


③

1” BOLT


④

LOCK WASHER


⑥

FLAT WASHER


⑦

NOTE: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled, go back and fully tighten all bolts. This will make it easier during assembly of unit.

10. Choose the option suits your needs. Locate LONG SPINE (D) or SHORT SPINE (D1) and set back face down on a scratch-free surface as shown above.

11. Fasten TOP SHELF FRAME (A) to the SPINE using two 5/8 ” BOLTS (3) with LOCK WASHERS

(6) and FLAT WASHERS (7). Make sure that the flush surfaces of TOP SHELF FRAME will face up after assembly.

12. Fasten the MIDDLE UPPER METAL FRAME (B), ADJUSTABLE SHELF FRAME (AA) and

BOTTOM SHELF FRAME (C) to the SPINE using six 1 ” BOLTS (4). Make sure the metal tabs on shelf frames point upward and the flush surfaces of ADJUSTABLE SHELF FRAME (AA) will face down after assembly. NOTE: Choose the upper hole sets for the ADJUSTABLE SHELF

FRAME (AA) to increase the bottom space.




5/8” BOLT


③

LOCK WASHER


⑥

FLAT WASHER


⑦

13. Fasten DIVIDER PANEL (I) to the middle rail of TOP SHELF FRAME (A) and MIDDLE UPPER

METAL FRAME (B) using four 5/8 ” BOLTS (3) and WASHERS (6 and 7).

NOTE: Make sure the drawer slides locate at bottom portion and slide opening face front of unit.




1” BOLT


④

LOCK WASHER


⑥

FLAT WASHER


⑦

14. Fasten the LEFT SIDE PANEL (G) to the LEFT SIDE FRAME (E) using four 1

” BOLTS (4) and

WASHERS (6 and 7).

NOTE: Make sure that the slide track on SIDE PANEL faces inward and the slide opening points toward the front end of SIDE FRAME (with metal brackets).

15. Repeat last step to fasten the RIGHT SIDE PANEL (H) to the RIGHT SIDE FRAME (F).




5/8” BOLT


③

D

LOCK WASHER


⑥

D1

E/F

A

7 6

3

FLAT WASHER


⑦

16. Stand last assemblies upright.

17. Fasten the LEFT SIDE FRAME (E) to the back rail of SHELF FRAMES (A, B, AA and C). Use four 5/8 ” BOLTS (3) and WASHERS (6 and 7).

18. Repeat last step for the RIGHT SIDE FRAME (F).




5/8” BOLT


A/B/C

J/K

J/K

③

7 6

5

E/F

7 6

3

1-5/8” BOLT


⑤

F

LOCK WASHER


⑥

FLAT WASHER


⑦

19. Fit and attach LEFT LEG (J) and RIGHT LEG (K) to the front of SIDE FRAMES (E and F) and

ADJUSTABLE SHELF FRAME (AA) using eight 5/8 ” BOLTS (3) with WASHERS (6 and 7) through the inner hole of metal brackets.

NOTE: Make sure top surfaces are even with each other and there are no gaps between

LEGS (J and K) and SIDE PANELS (G and H).

20. Fasten LEGS (J and K) to the front rail of SHELF FRAMES (A, B and C). Use six 1-5/8 ”

BOLTS (5) and WASHERS (6 and 7) through the outer hole of metal brackets on SIDE

FRAMES (E and F).




21. Go back and tighten all bolts with enclosed M4 ALLEN WRENCH.

22. Adjust the FLOOR LEVELERS pre-attached at the bottom of LEGS (J and K) to level the unit.

If you choose Table-top configuration, continue to next step.

If mounting TV with the Floating Swivel

Mount, skip ahead to PAGE 21.



Assembly Instructions for Table-top

5/8” BOLT


③

D1

BB

CC

3

3

23. Attach GAMING GUITAR CLIP (BB) and CABLE WHEELS (CC) onto the backside of SHORT

SPINE (D1) using five 5/8

” BOLTS (3).

NOTE: You can use the CABLE WHEELS to help keep your entertainment center’s cables and cords organized. The GAMING GUITAR CLIP (BB) can provide storage of gaming guitar controllers.




I

G/H/I

V/W

24. To insert the assembled drawers into your unit, extend the SLIDE TRACKS on the SIDE

PANELS (G and H) and DIVIDER PANEL (I) all the way forward (including ball bearing cart).

Then align the SLIDE RUNNERS on the assembled drawers with the SLIDING TRACKS and push the drawer carefully inside until it stops.

NOTE: If they do not go smoothly, please take out and repeat the step. If you need to remove the drawer, please pull the drawer all the way out, then simultaneously push the PLASTIC

RELEASE LEVER of the ball bearing slides up on one side and down on the other side, and then pull it completely out.




SUCTION CUP


AA

C

1

11

GLASS BUMPER


C/AA

① ⑪

25. Put SUCTION CUPS (1) firmly into the top holes of TOP SHELF FRAME (A) and evenly place the GLASS BUMPERS (11) on the ADJUSTABLE SHELF FRAME (AA) and BOTTOM SHELF

FRAME (C) as shown above.

Tip: If a SUCTION CUP resists insertion, try pressing down on the middle of the cup with the

Allen Wrench while twisting it clockwise into the hole.

26. Place GLASS SHELVES (L and M) with the black side of glass down onto the SUCTION

CUPS (1) and GLASS BUMPER (11). Push each glass all the way back against the SPINE.

NOTE: If glass is scratched you can minimize the damage by using a BLACK marker and filling in scratched area from underneath.



Assembly Instructions

ACRYLIC STOPPER


⑭

L

NOTE: You must install the Acrylic TV Stopper to prevent TV from tipping when placing your flat panel television directly on the table-top console.

27. Remove the tape of ACRYLIC STOPPER (14) and place it on the cut-out of the warning label on the front of TOP GLASS (L). Make sure it is aligned before applying pressure.

28. Remove the warning label for ACRYLIC STOPPER carefully.




Tools required: Allen Wrench (provided), Phillips Screwdriver, Mallet, Power Drill, and 3/8

” Drill Bit.

29. Position the assembled Table-top in your desired location against a wall. Now follow the instructions printed on the plastic bag containing the TIPPING RESTRAINT HARDWARE to mount the tipping restraint to the SPINE and the wall.

NOTE: YOU MUST USE THIS TIPPING RESTRAINT TO ATTACH THIS UNIT TO THE

WALL, TO PREVENT ACCIDENTS AND/OR INJURIES.

30. The Table-top is ready for use now. Be sure to position your Flat Panel TV in center of the console.

NOTE: For Tilting Wall Mount, proceed to PAGE #30.



A s s e m b l y I n s t r u c t i o n s f o r

F l o a t i n g S w i v e l M o u n t

5/8” BOLT


LOCK WASHER


FLAT WASHER


③ ⑥ ⑦

31. Fasten the SWIVELING BRACKET (N) to the top of LONG SPINE (D) with six 5/8

” BOLTS (3) and WASHERS (6 and 7). Make sure the pivoting bolt head is up. Tighten the bolts with enclosed M4 Allen Wrench.

NOTE: The Spine can provide four height options for your TV set. Refer to your TV size, adjust the Swiveling Bracket at your desired height to offer optimum viewing.



Assembly Instructions for Floating Swivel Mount

1/2” BOLT


②

LOCK WASHER


⑥

FLAT WASHER


⑦

The SENSOR/SOUND SHELF (R) provides two options: position gaming accessories above

TV or sound bar below TV.

32. Choose the option you prefer, slide SSS SPINE (Q) onto the XYZ MOUNTING FRAME (O) properly. Adjust the height of SSS SPINE and attach in place using four 1/2

” BOLTS (2) and

WASHERS (6 and 7). Make sure the SENSOR/SOUND SHELF (R) will not hit your TV.




O

7

6

2

N

D

7

6

7

6

1/2” BOLT


LOCK WASHER


FLAT WASHER


② ⑥ ⑦

33. Hold and attach the flat side of XYZ MOUNTING FRAME (O) onto the SWIVELING BRACKET

(N) using four 1/2

” BOLTS (2) and WASHERS (6 and 7). Make sure the recess holes on the

XYZ MOUNTING FRAME are at the bottom.




R

34. Pick up SENSOR/SOUND SHELF (R) and securely fit the back tabs into the small slots of

SSS SPINE (Q). Tighten both LOCK BOLTS pre-attached on the SSS SPINE with a PHILLIPS

SCREWDRIVER until they hit the back tabs of SENSOR/SOUND SHELF.



Mounting Monitor Brackets to a Television with a Flat Back

NOTE: For televisions with a curved back or recessed back proceed directly to next page.

35. Determine the correct diameter of the bolt your TV requires by hand threading them into the threaded insert on the back of the TV. If you encounter any resistance, stop immediately. If you are unable to find the correct bolt consult a local hardware store.

36. Follow the appropriate diagram above to attach MONITOR BRACKETS (PL/PR) to the back of your TV with selected fasteners. Make sure the MONITOR BRACKETS are centered and level with each other. Secure the bolts with a PHILLIPS SCREWDRIVER. DO NOT over tighten the bolts.

NOTE: Lean the TV up against a wall or other solid surface when attaching with the Monitor

Brackets. DO NOT place the TV face down on the glass this may cause permanent damage.



Mounting Monitor Brackets to a Television with a Curved/Recess Back

37. Determine the correct diameter of the bolt your TV requires by hand threading them into the threaded insert on the back of the TV. If you encounter any resistance, stop immediately. If you are unable to find the correct bolt consult a local hardware store.

38. Follow the appropriate diagram above to attach MONITOR BRACKETS (PL/PR) to the back of your TV with selected fasteners. Make sure the MONITOR BRACKETS are vertically centered and level with each other. Secure the bolts with a PHILLIPS SCREWDRIVER. DO NOT over tighten the bolts.




PL/PR

2

O

1

PL/PR

O

PR

PL

O

MAKE SURE ALL BOLTS ARE TIGHT AND SPINE IS AT A 90 DEGREE ANGLE AND USING

A QUALITY LEVEL TO VERIFY THE MOUNTING FRAME IS LEVEL PRIOR TO

INSTALLATION OF TV.

39. Ask for assistance to lift the television up to hang the MONITOR BRACKETS (PL/PR) onto the

XYZ MOUNTING FRAME (O). Set the hooks on MONITOR BRACKETS over the MOUNTING

FRAME then lower them onto the bars of MOUNTING FRAME.

NOTE: Loosen the LOCK BOLT pre-attached on the MONITOR BRACKETS to ensure an easy fit at the bottom hooks.

40. Center the television and tighten both LOCK BOLTS with a long PHILLIPS SCREWDRIVER until they hit underside of XYZ MOUNTING FRAME (O) to secure it in place.




41. The MONITOR BRACKETS (PL/PR) can tilt up to 11˚ downward and 5˚ upward, depending on your optimum viewing position. Have your assistant hold the TV steady before you start to adjust the tilt. Simply reach behind the TV and turn the both Tilt Adjustment Knobs with enclosed 3/16 ” ALLEN WRENCH to adjust your TV to provide optimum viewing and minimize glare.




Tools required: Allen Wrench (provided), Phillips Screwdriver, Mallet, Power Drill, and 3/8 ” Drill Bit.

42. Repeat the same process to attach the GAMING GUITAR CLIP (BB) and CABLE

WHEELS (CC) and install the TOP GLASS (L) and GLASS SHELVES (M) in place.

43. Carefully move the console and position in your desired location against a wall. Now follow the instructions printed on the plastic bag containing TIPPING RESTRAINT HARDWARE KIT to mount the tipping restraint to the SPINE and the wall.

NOTE: You must install the Tipping Restraint Hardware with the unit in use to prevent any accidents or damage to the unit.

44. You can enjoy your home entertainment center now. Swivel left-or-right for optimum viewing control.

45. Optional wood SPINE DECORATIVE PANEL (Z) is provided. If needed, remove the back tapes and stick the panel to the front of LONG SPINE (D). Make sure it is centered properly.



The following steps are only for those who wish to mount their

TV directly to the wall. If you have already mounted your TV to the Swinging Floater or plan to display your TV on the top surface of the stand, disregard the following steps.

Assembly Instructions for Universal Wall Mount

Installing XYZ Mounting Frame onto WOODEN STUD WALL

NOTE: If you are mounting your TV onto brick, solid concrete or concrete block, skip this section.

This assembly requires an electric drill, level and stud finder (not included).

46. Using a stud finder, locate the edges of the wood studs. Find the center line of each stud and draw a vertical reference line on the wall over each one. Place the XYZ MOUNTING FRAME

(O) level against the wall where you intend to mount the TV. Using the MOUNTING FRAME (O) as a template, mark 4 drill points (2 on top, 2 on bottom) with a pencil on the vertical reference lines you just drew.

47. With an electric drill (not included) drill 3/16 inch diameter holes to at least 2½ inch deep on the four drill points. While holding the Bracket Plate in place, loosely screw in the Lag Bolts (9).

48. Secure the XYZ MOUNTING FRAME (O) to wall with LAG BOLTS (9) and WASHERS (8) at the drill points. Tighten bolts firmly, but be careful not to over-tighten.

Do not over-tighten the Lag Bolts. Tighten Lag Bolts only until the Lag

Bolt Washer is pulled firmly against the metal plate of Mounting Frame. If there is a layer of drywall or other material, this drywall or other material may not exceed 5/8 inch in thickness. Failure to heed this caution may result property damage and/or personal injury.



Assembly Instruction for installing XYZ Mounting Frame onto BRICK,

SOLID CONCRETE OR CONCRETE BLOCK

Maximum weight 135 lb. (61.2 kg)

Concrete Anchors should only be used for masonry mounting.

NEVER use the wall anchors to mount the unit to drywall.

NOTE: If you are mounting your TV to a wall with wooden studs, skip this section.

This assembly requires an electric drill and level (not included).

49. Begin by placing the XYZ Mounting Frame (O) level against the wall where you intend to mount the TV. Using the Mounting Frame (O) as a template, mark 4 drill points with a pencil.

50. With an electric drill (not included) on its low setting, drill 7/16 inch diameter holes to at least

2½ inch deep. Insert Concrete Anchors (10) into pre-drilled holes so that they are flush with the wall.

51. Place the XYZ Mounting Frame (O) level in the desired position against the wall. Secure the

Mounting Frame (O) to wall with Lag Bolts (9) and washers (8) at the drill points. Tighten bolts firmly, but be careful not to over-tighten.




52. The Sensor/Sound Shelf (R) provides two options: position gaming accessories above TV or sound bar below TV. Choose the option you prefer, slide SSS Spine (Q) onto the XYZ

Mounting Frame (O) properly. Adjust the height of SSS Spine and attach in place. Make sure the Sensor/Sound Shelf (R) will not hit your TV.

53. Once the Monitor Brackets (PL/PR) are attached onto the back of television, ask for assistance to lift the television up to attach the Monitor Brackets onto the XYZ Mounting

Frame (O). Set the hooks on Monitor Brackets over the Mounting Frame then lower them onto the bars of Mounting Frame. Proceed to center the television.

54. If you want to adjust the tilt, ask for help from your friends to hold the TV steady before you start to adjust. Simply turn the both Tilt Adjustment Knobs on Monitor Brackets (PL/PR) with

3/16

” Allen Wrench to adjust your TV to provide optimum viewing and minimize glare. When the TV is in its intended position, tighten both Lock bolts with a long Phillips Screwdriver until they hit underside of XYZ Mounting Frame (O) to ensure your TV is safe and secure on the wall.

55. Repeat the process on page 24 to install Sensor/Sound Shelf (R) onto the SSS Spine (Q).

56. Place assembled console under your TV set. Finally, connect the A/V and power cables to your

TV. You are now ready to enjoy your wall-mounted Flat Panel TV.



Care and Maintenance

 Use a soft, clean cloth that will not scratch the surface when dusting.

 Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.

 Using solvents of any kind on your furniture may damage the finish.

 Never use water to clean your furniture as it may cause damage to the finish.

 Always use coasters under beverage glasses and flowerpots.

 Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing.

 Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create spotting within the furniture finish.

 Stains or marks from crayons or ink markers will be difficult to remove.

 In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a professional to repair your furniture.

 Check bolts/screws periodically and tighten them if necessary.

Further advice about furniture care

It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from direct sunlight as sun may damage the finish.

Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful tips will enhance your furniture as it ages.

A Touch-up Pen has been provided to repair any small nicks or scratches that may occur during assembly or shipping.

We hope you enjoy your purchase for many years.

Thank you for your purchase!

QUALITY GUARANTEE

We are confident that you will be delighted with your Whalen Furniture purchase.

Should this product be defective in workmanship or materials or fail under normal use, we will repair or replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet your highest expectations. We guarantee that you will immediately see the value of our fine furniture.

This warranty gives you specific legal rights and you may also have other rights which vary from State to State (province to province).

Customer Service: 1-866-942-5362

8:30 a.m. - 4:30 p.m., PST, Monday to Friday www.whalenstyle.com



Whalen XLGTD-8 XLGTD-8 Gaming Theater™ Console User manual 34 Pages

Whalen XLGTD-8 XLGTD-8 Gaming Theater™ Console User manual

ADULT ASSEMBLY REQUIRED

WMCXLGTD-8

M A X I M U M R E C O M M E N D E D W E I G H T L O A D S

7 6

3

A/B/C

J/K

J/K

7 6

5

E/F

7 6

3

If you choose Table-top configuration, continue to next step.

If mounting TV with the Floating Swivel

Mount, skip ahead to PAGE 21.

BB

G/H/I

V/W

Assembly Instructions for Table-top

PL/PR

O

PL/PR

O

The following steps are only for those who wish to mount their

TV directly to the wall. If you have already mounted your TV to the Swinging Floater or plan to display your TV on the top surface of the stand, disregard the following steps.

Care and Maintenance

Further advice about furniture care

QUALITY GUARANTEE

Related manuals

Whalen XLGTD-8 XLGTD-8 Gaming Theater™ Console User manual 34 Pages

Whalen XLGTD-8 XLGTD-8 Gaming Theater™ Console User manual

ADULT ASSEMBLY REQUIRED

WMCXLGTD-8

M A X I M U M R E C O M M E N D E D W E I G H T L O A D S

7 6

3

A/B/C

J/K

J/K

7 6

5

E/F

7 6

3

If you choose Table-top configuration, continue to next step.

If mounting TV with the Floating Swivel

Mount, skip ahead to PAGE 21.

BB

G/H/I

V/W

Assembly Instructions for Table-top

PL/PR

O

PL/PR

O

The following steps are only for those who wish to mount their

TV directly to the wall. If you have already mounted your TV to the Swinging Floater or plan to display your TV on the top surface of the stand, disregard the following steps.

Care and Maintenance

Further advice about furniture care

QUALITY GUARANTEE

Related manuals

Riverside Furniture

81068

Riverside Furniture

81069

Leick Home

10074-GR

Whalen Furniture

TGXLD-1

Crosley Furniture

CF1309

Unbranded

BH-1236-0252

Leick Home

11404

Leick Home

11432

MOR/ryde

TV5-003H

Home Decorators Collection

1753400820

Whalen

XLDEC54-NV

HAI

Omni 33A00-3