ONIX Installation Guide

ONIX Installation Guide
ONIX_IDMK_IG_532105-2_A.qxp:ONIX Installation Guide
6/1/15
12:00 PM
Page 4
4
IN-DASH MOUNTING Installation Guide
CONTACT HUMMINBIRD
Web site
E-mail
Telephone
Direct Shipping
humminbird.com
532105-2_A
ENVIRONMENTAL COMPLIANCE STATEMENT: It is the intention of
Johnson Outdoors Marine Electronics, Inc. to be a responsible
corporate citizen, operating in compliance with known and applicable
environmental regulations, and a good neighbor in the communities
where we make or sell our products.
service@humminbird.com
1-800-633-1468
Humminbird
Service Department
678 Humminbird Lane
Eufaula, AL 36027 USA
WARNING! This device should not be used as a navigational aid
to prevent collision, grounding, boat damage, or personal injury.
When the boat is moving, water depth may change too quickly
to allow time for you to react. Always operate the boat at very
slow speeds if you suspect shallow water or submerged objects.
WARNING! Disassembly and repair of this electronic unit should
only be performed by authorized service personnel. Any
modification of the serial number or attempt to repair the
original equipment or accessories by unauthorized individuals
will void the warranty.
WARNING! This product contains chemicals known to the State
of California to cause cancer and birth defects or other
reproductive harm.
WARNING! Do NOT travel at high speed with the unit cover
installed. Remove the unit cover before traveling at speeds above
20 mph.
WEEE DIRECTIVE: EU Directive 2002/96/EC “Waste of Electrical and
Electronic Equipment Directive (WEEE)” impacts most distributors,
sellers, and manufacturers of consumer electronics in the European
Union. The WEEE Directive requires the producer of consumer
electronics to take responsibility for the management of waste from
their products to achieve environmentally responsible disposal during
the product life cycle.
WEEE compliance may not be required in your location for electrical &
electronic equipment (EEE), nor may it be required for EEE designed
and intended as fixed or temporary installation in transportation
vehicles such as automobiles, aircraft, and boats. In some European
Union member states, these vehicles are considered outside of the
scope of the Directive, and EEE for those applications can be
considered excluded from the WEEE Directive requirement.
This symbol (WEEE wheelie bin) on product indicates the
product must not be disposed of with other household refuse. It
must be disposed of and collected for recycling and recovery of
waste EEE. Johnson Outdoors Marine Electronics, Inc. will mark
all EEE products in accordance with the WEEE Directive. It is our goal to
comply in the collection, treatment, recovery, and environmentally
sound disposal of those products; however, these requirements do vary
within European Union member states. For more information about
where you should dispose of your waste equipment for recycling and
recovery and/or your European Union member state requirements,
please contact your dealer or distributor from which your product was
purchased.
ROHS STATEMENT: Product designed and intended as a fixed
installation or part of a system in a vessel may be considered beyond
the scope of Directive 2002/95/EC of the European Parliament and of
the Council of 27 January 2003 on the restriction of the use of certain
hazardous substances in electrical and electronic equipment.
1
532105-2_A
IN-DASH MOUNTING Installation Guide
OVERVIEW
Following are instructions for the installation of this accessory. Before you start the installation, we
encourage you to read these instructions carefully in order to get the full benefit from your
Humminbird® accessory.
Installation Kit: This accessory includes the following supplies*:
• (2) bolts, hex head 1/4-20 x 4"
• (2) 1/4" split-ring washers
• (2) hex nuts, 1/4 - 20
• (2) screws, 1/4-20 x 3/8"
• (2) end caps
• (1) mounting template
*Product supplies and features are subject to change without notice.
Customer Service: If you find that any items are missing from your installation kit, visit our Web site
at humminbird.com or call Customer Service at 1-800-633-1468.
Supplies: In addition to the hardware supplied with your installation kit, you will need a drill and various
drill bits, a cutting tool for the dashboard material, a Phillips head screwdriver, a wrench, safety glasses
and a dust mask, and masking tape.
INSTALLATION
Perform the procedures in the following sections to in-dash mount the ONIX® control head.
NOTE: Your control head might not look exactly like the illustrations in this guide, but the
control head will mount in the same way.
1 | Determine the Mounting Location
Start by locating a suitable, flat area of the dashboard for mounting. Consider the following to find the
best mounting location:
Planning Depth Space for the
Control Head and Cables
• Standard Compass Safe Distance: The control head must be installed at least 4 ft (1.2 m)
from the compass or other magnetic equipment on the vessel. Also, see your compass
installation guide for details.
• Interference: The mounting location must provide adequate distance from electric motors or
any equipment that may cause electronic interference.
• Stability: The mounting area should be protected from waves, shock, vibration, and water.
• Visibility: The operator must have a clear view of the screen during operation. Review the visibility
in relation to other dashboard equipment, sun, and the operator’s main steering position.
• Cover: See the In-dash Mounting Template to allow space for the cover.
• Depth: The mounting area should have a depth of 6" (152.4 mm) to allow space for the control
head and cables.
6" (152.4 mm)
• Ventilation: The area beneath the mounting surface should be well-ventilated.
• Accessibility: The location should be easily accessible for all cables to reach the ports on the
back of the control head.
NOTE: If a cable is too short for your application, extension cables are available. For
assistance, contact Customer Service.
© 2015 Johnson Outdoors Marine Electronics, Inc. All rights reserved.
ONIX_IDMK_IG_532105-2_A.qxp:ONIX Installation Guide
6/1/15
12:00 PM
Page 2
2
532105-2_A
IN-DASH MOUNTING Installation Guide
3
532105-2_A
IN-DASH MOUNTING Installation Guide
4 | Install the Control Head
2 | Cut the In-Dash Mounting Hole
To in-dash mount the ONIX control head, start by placing the hardware on the surfaces where you plan
to install them.
1. Confirm you have the correct In-dash Mounting Template for your control head model.
Installing the Screws
1. Carefully lower the control head into the mounting hole.
2. From under the dash, slide the bracket arms onto the control head. Line up the screw holes on
the bracket arms with the screw holes on the control head (see the illustration below and the
illustration Installing the Screws).
2. Review the instructions, measurements, and cutting options on the template before you
proceed with the installation.
split-ring
washer
control head
3. Tape the template to the chosen mounting location.
dashboard
(partial view)
4. Using the template, select the cutting method that is best for your boat:
nut
Drill one entry hole away from the main cut line that is large enough to insert the blade of your
cutting tool.
OR
bracket
Drill a corner hole away from the main cut line using a drill bit that will create a hole as close as
possible to the diameter measurement shown on the template. Repeat for the other three
corners as indicated on the template. Use one of the corner holes as an entry hole, or drill an
additional entry hole away from the main cut line.
5. Carefully begin cutting toward the dotted cut line, and continue cutting to the inside of the line
around the template.
CAUTION! The corner cut lines are critical to the installation. Carefully cut along the inside
of the line.
6. Test the Mounting Hole: Install the control head in the mounting hole to test the fit. Make
adjustments to the mounting hole as needed. Remove the control head and template when
finished.
7. Thoroughly clean and deburr the mounting hole.
screw hole
screw hole
screw hole
3. Install each 3/8" (9.5 mm) screw using a Phillips head screwdriver. Make sure the bracket stays
level and doesn’t block the control head ports. Hand tighten only.
Securing the Installation
end cap flush
against the
dashboard
4. Hand-tighten each bolt until the end cap is flush against the dash (see the illustration Securing
the Installation). Do NOT overtighten the bolts.
5. Using a wrench, hand tighten each nut so the split-ring washer flattens against the bracket.
CAUTION! The split-ring washers must be fully compressed for a secure installation.
3 | Install the Bracket
5 | Route and Connect the Cables
1. Install one nut and one split-ring washer onto each 4" (101.6 mm) bolt. See the illustration
below.
1. See the installation guides included with each hardware component to install power, GPS, and
other optional equipment (transducer, radar, AIS, autopilot, and accessories).
2. Insert each bolt into each threaded bolt hole on the bracket. Hand-tighten the bolts until they
are installed approximately 1" (25.4 mm) through the bracket. You will fully tighten the bolts in
a later step.
CAUTION! Do NOT mount the cables where the connectors could be submerged in water or
flooded. If cables are installed in a splash-prone area, it may be helpful to apply dielectric
grease to the inside of the connectors to prevent corrosion. Dielectric grease can be
purchased separately from a general hardware or automotive store.
hand tighten each nut until
the split-ring washer flattens
Securing the Cables
(magnified view)
2. Route the cables to the control head and insert the connectors into the proper ports on the
control head. The ports are labeled and the cable connectors are keyed to prevent incorrect
installation, so be careful not to force the connectors into the ports.
4" bolt
nut
split-ring washer
3. Install one end cap on the end of each bolt.
cable label
(optional)
3. Hand tighten the screw nut on each cable to secure the connection. Any unused ports should
be covered with the port covers to prevent potential damage.
4. Apply labels to the cables (optional, not included). Use nylon cable ties (not included) to secure
the cables and create a clean assembly.
5. See the Humminbird Operations Manual to configure the control head.
end cap
screw nut
port cover
ONIX_IDMK_IG_532105-2_A.qxp:ONIX Installation Guide
6/1/15
12:00 PM
Page 2
2
532105-2_A
IN-DASH MOUNTING Installation Guide
3
532105-2_A
IN-DASH MOUNTING Installation Guide
4 | Install the Control Head
2 | Cut the In-Dash Mounting Hole
To in-dash mount the ONIX control head, start by placing the hardware on the surfaces where you plan
to install them.
1. Confirm you have the correct In-dash Mounting Template for your control head model.
Installing the Screws
1. Carefully lower the control head into the mounting hole.
2. From under the dash, slide the bracket arms onto the control head. Line up the screw holes on
the bracket arms with the screw holes on the control head (see the illustration below and the
illustration Installing the Screws).
2. Review the instructions, measurements, and cutting options on the template before you
proceed with the installation.
split-ring
washer
control head
3. Tape the template to the chosen mounting location.
dashboard
(partial view)
4. Using the template, select the cutting method that is best for your boat:
nut
Drill one entry hole away from the main cut line that is large enough to insert the blade of your
cutting tool.
OR
bracket
Drill a corner hole away from the main cut line using a drill bit that will create a hole as close as
possible to the diameter measurement shown on the template. Repeat for the other three
corners as indicated on the template. Use one of the corner holes as an entry hole, or drill an
additional entry hole away from the main cut line.
5. Carefully begin cutting toward the dotted cut line, and continue cutting to the inside of the line
around the template.
CAUTION! The corner cut lines are critical to the installation. Carefully cut along the inside
of the line.
6. Test the Mounting Hole: Install the control head in the mounting hole to test the fit. Make
adjustments to the mounting hole as needed. Remove the control head and template when
finished.
7. Thoroughly clean and deburr the mounting hole.
screw hole
screw hole
screw hole
3. Install each 3/8" (9.5 mm) screw using a Phillips head screwdriver. Make sure the bracket stays
level and doesn’t block the control head ports. Hand tighten only.
Securing the Installation
end cap flush
against the
dashboard
4. Hand-tighten each bolt until the end cap is flush against the dash (see the illustration Securing
the Installation). Do NOT overtighten the bolts.
5. Using a wrench, hand tighten each nut so the split-ring washer flattens against the bracket.
CAUTION! The split-ring washers must be fully compressed for a secure installation.
3 | Install the Bracket
5 | Route and Connect the Cables
1. Install one nut and one split-ring washer onto each 4" (101.6 mm) bolt. See the illustration
below.
1. See the installation guides included with each hardware component to install power, GPS, and
other optional equipment (transducer, radar, AIS, autopilot, and accessories).
2. Insert each bolt into each threaded bolt hole on the bracket. Hand-tighten the bolts until they
are installed approximately 1" (25.4 mm) through the bracket. You will fully tighten the bolts in
a later step.
CAUTION! Do NOT mount the cables where the connectors could be submerged in water or
flooded. If cables are installed in a splash-prone area, it may be helpful to apply dielectric
grease to the inside of the connectors to prevent corrosion. Dielectric grease can be
purchased separately from a general hardware or automotive store.
hand tighten each nut until
the split-ring washer flattens
Securing the Cables
(magnified view)
2. Route the cables to the control head and insert the connectors into the proper ports on the
control head. The ports are labeled and the cable connectors are keyed to prevent incorrect
installation, so be careful not to force the connectors into the ports.
4" bolt
nut
split-ring washer
3. Install one end cap on the end of each bolt.
cable label
(optional)
3. Hand tighten the screw nut on each cable to secure the connection. Any unused ports should
be covered with the port covers to prevent potential damage.
4. Apply labels to the cables (optional, not included). Use nylon cable ties (not included) to secure
the cables and create a clean assembly.
5. See the Humminbird Operations Manual to configure the control head.
end cap
screw nut
port cover
ONIX_IDMK_IG_532105-2_A.qxp:ONIX Installation Guide
6/1/15
12:00 PM
Page 4
4
IN-DASH MOUNTING Installation Guide
CONTACT HUMMINBIRD
Web site
E-mail
Telephone
Direct Shipping
humminbird.com
532105-2_A
ENVIRONMENTAL COMPLIANCE STATEMENT: It is the intention of
Johnson Outdoors Marine Electronics, Inc. to be a responsible
corporate citizen, operating in compliance with known and applicable
environmental regulations, and a good neighbor in the communities
where we make or sell our products.
service@humminbird.com
1-800-633-1468
Humminbird
Service Department
678 Humminbird Lane
Eufaula, AL 36027 USA
WARNING! This device should not be used as a navigational aid
to prevent collision, grounding, boat damage, or personal injury.
When the boat is moving, water depth may change too quickly
to allow time for you to react. Always operate the boat at very
slow speeds if you suspect shallow water or submerged objects.
WARNING! Disassembly and repair of this electronic unit should
only be performed by authorized service personnel. Any
modification of the serial number or attempt to repair the
original equipment or accessories by unauthorized individuals
will void the warranty.
WARNING! This product contains chemicals known to the State
of California to cause cancer and birth defects or other
reproductive harm.
WARNING! Do NOT travel at high speed with the unit cover
installed. Remove the unit cover before traveling at speeds above
20 mph.
WEEE DIRECTIVE: EU Directive 2002/96/EC “Waste of Electrical and
Electronic Equipment Directive (WEEE)” impacts most distributors,
sellers, and manufacturers of consumer electronics in the European
Union. The WEEE Directive requires the producer of consumer
electronics to take responsibility for the management of waste from
their products to achieve environmentally responsible disposal during
the product life cycle.
WEEE compliance may not be required in your location for electrical &
electronic equipment (EEE), nor may it be required for EEE designed
and intended as fixed or temporary installation in transportation
vehicles such as automobiles, aircraft, and boats. In some European
Union member states, these vehicles are considered outside of the
scope of the Directive, and EEE for those applications can be
considered excluded from the WEEE Directive requirement.
This symbol (WEEE wheelie bin) on product indicates the
product must not be disposed of with other household refuse. It
must be disposed of and collected for recycling and recovery of
waste EEE. Johnson Outdoors Marine Electronics, Inc. will mark
all EEE products in accordance with the WEEE Directive. It is our goal to
comply in the collection, treatment, recovery, and environmentally
sound disposal of those products; however, these requirements do vary
within European Union member states. For more information about
where you should dispose of your waste equipment for recycling and
recovery and/or your European Union member state requirements,
please contact your dealer or distributor from which your product was
purchased.
ROHS STATEMENT: Product designed and intended as a fixed
installation or part of a system in a vessel may be considered beyond
the scope of Directive 2002/95/EC of the European Parliament and of
the Council of 27 January 2003 on the restriction of the use of certain
hazardous substances in electrical and electronic equipment.
1
532105-2_A
IN-DASH MOUNTING Installation Guide
OVERVIEW
Following are instructions for the installation of this accessory. Before you start the installation, we
encourage you to read these instructions carefully in order to get the full benefit from your
Humminbird® accessory.
Installation Kit: This accessory includes the following supplies*:
• (2) bolts, hex head 1/4-20 x 4"
• (2) 1/4" split-ring washers
• (2) hex nuts, 1/4 - 20
• (2) screws, 1/4-20 x 3/8"
• (2) end caps
• (1) mounting template
*Product supplies and features are subject to change without notice.
Customer Service: If you find that any items are missing from your installation kit, visit our Web site
at humminbird.com or call Customer Service at 1-800-633-1468.
Supplies: In addition to the hardware supplied with your installation kit, you will need a drill and various
drill bits, a cutting tool for the dashboard material, a Phillips head screwdriver, a wrench, safety glasses
and a dust mask, and masking tape.
INSTALLATION
Perform the procedures in the following sections to in-dash mount the ONIX® control head.
NOTE: Your control head might not look exactly like the illustrations in this guide, but the
control head will mount in the same way.
1 | Determine the Mounting Location
Start by locating a suitable, flat area of the dashboard for mounting. Consider the following to find the
best mounting location:
Planning Depth Space for the
Control Head and Cables
• Standard Compass Safe Distance: The control head must be installed at least 4 ft (1.2 m)
from the compass or other magnetic equipment on the vessel. Also, see your compass
installation guide for details.
• Interference: The mounting location must provide adequate distance from electric motors or
any equipment that may cause electronic interference.
• Stability: The mounting area should be protected from waves, shock, vibration, and water.
• Visibility: The operator must have a clear view of the screen during operation. Review the visibility
in relation to other dashboard equipment, sun, and the operator’s main steering position.
• Cover: See the In-dash Mounting Template to allow space for the cover.
• Depth: The mounting area should have a depth of 6" (152.4 mm) to allow space for the control
head and cables.
6" (152.4 mm)
• Ventilation: The area beneath the mounting surface should be well-ventilated.
• Accessibility: The location should be easily accessible for all cables to reach the ports on the
back of the control head.
NOTE: If a cable is too short for your application, extension cables are available. For
assistance, contact Customer Service.
© 2015 Johnson Outdoors Marine Electronics, Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising