FAAC Swing Gate Systems

FAAC Swing Gate Systems
O p e n i n g a W h o l e N e w Wo r l d :
FAAC Sw ing Gate Systems
Models402 & 422
The Models 402 and 422 hydraulic
Swing Gate Operators
swing gate operators are designed for
Slide Gate Operators
private residences. They offer many
Barrier Gate Operators
of the benefits of a large gate operator
Accessories
in a compact form.
The Models 402 and 422 are
UL 325 compliant.
FAAC is the world’s
largest specialized
manufacturer of gate
operating equipment.
Model 402 and 422
Hydraulic Swing
Model 402 and 422 Kits include:
Gate Operators
The Models 402 and 422 hydraulic swing gate
operator are designed for private residences.
They offer many of the benefits of a large gate
operator in a compact form.
positions. Both models have versions that
allow your gate system be set up to provide
special options including “gate-safe” or “
gate-secure” configurations:
A high-speed version of the 422 is available
for pedestrian gates that require quick closure.
• Gate-safe: during power outages, a
magnetic lock releases a closed gate to
permit emergency access.
• Gate-secure: during power outages, an
electric lock keeps a closed gate locked.
Hydraulic swing gate operators are inherently
safer than other types of operators because
they have fewer “pinch points.” In addition,
FAAC 402 and 422 operators are equipped
with a hydraulic bypass valve for extra entrapment protection and a manual release that
allows you to operate your gate if there is
a power failure. A battery back-up unit is
also available.
The 402 hydraulic system can hydraulically lock
the gate in your choice of the opened or closed
positions.
The 422 system can hydraulically lock the gate
in your choice of the opened and/or closed
The versatile FAAC control panel allows for six
operating modes including garage-door-like
operation and a new HOLD OPEN function.
The 402 and 422 can be mounted inside the
gate and still allow the gate to open to the
inside or to the outside. All FAAC operators
can be finished to blend with the gate.
. One or two hydraulic gate operators with
mounting hardware
. One 450 MPS control panel
. One 14 x 16 in. weather resistant UL Listed
fiberglass enclosure
. Two photobeam sets for opening and closing
reversing devices
. One or two manual release keys
. One plug-in radio receiver
. Two radio transmitters
. 115 VAC receptacle for accessories (5 amp max.)
. ON/OFF switch controlling power to control panel,
accessories and plug outlet
. Pre-wired for dual photobeams – open and closing
reversing devices
. Pre-wired motors to terminal strip
. Pre-wired Open/Hold Open contacts
. Test button
. Two or four warning signs
All swing gates require gate stops that limit
the travel of each gate leaf and thus protect
the operator. Optional concealed gate stops
are available.
Model 402
Model 422
A convenient manual release is standard
on all models.
Use FAAC to build a complete gate system
Model 450
pre-wired control panel
Telephone entry systems
Electric and
magnetic locks
Battery back-up
Some access control
options to open a gate
Loops and photobeam safety
Model 402 and 422
hydraulic swing
gate operators
Photobeams
All Model 402 and 422 kits include
a Model 450 MPS Control panel.
Positive gate stops
Positive gate stops, which limit the travel of each gate leaf, are required in the opened and
closed positions for all gate systems using FAAC operators.
FAAC offers three innovative gate stops. The Stop-O-Matic Model 80 is an adjustable gate
stop that attaches directly to the gate operator. For aesthetic purposes, the Model 80 is totally concealed under the operator cover.
GATE CLOSED
GATE OPEN
Features include:
. Stainless steel construction
. Mounts with existing FAAC hardware and does not require additional attachment points
. Accommodates inward or outward swing with no additional fabrication
. Maximum degrees of swing: limited by operator
. Maximum leaf length & weight: limited by operator
features include:
. One 450 MPS operates single leaf or
bi-parting gates
. Easy interconnection of loop detectors,
photobeams, etc. to reverse a gate if
an obstacle is sensed
. Easy interconnection of actuating devices
like remote control radios, key pads and
telephone entry systems
. Selectable logics:
. A (automatic): The gate opens on command
and automatically closes after a pause
phase. A second command on opening is
ignored; a second command during the
pause phase interrupts the pause time; a
second command durring closing reopens
the gate. A maintained open command will
hold the gate open.
. S (security): The security mode is like A
logic except that a second signal during
opening immediately closes the gate.
. E (semi-automatic): Garage-door-like
operation. This mode requires a signal
to open and a signal to close. A second
signal during opening or closing causes
the gate to stop. A third signal then
closes the gate.
. EP (semi-automatic): Similar to E logic,
but second signal stops gate, third signal
reverses gate.
. B (manned): Designed for guard station
use and requires a 3-button switch
(pulsed) to open, close and stop the gate.
. C (manned and constant): Similar to
B logic, but 3-button switch requires
constant pressure on each button.
Duty Cycle
Typical Use
Class 1
Residential
vehicular gate
operator
400, 412, 402
422, 750, 760
620, 640, 885
Limited
duty
.Home use
.Small apartment
Class 4 Class 3 Class 2
UL 325 Class Descriptions & FAAC Operators
FAAC Models
Commercial/General
access vehicular
gate operator
Industrial/Limited
access vehicular
gate operator
Restricted Access
vehicular gate
operator
400, 620, 640
885
Continuous
duty
building, up to 4
units per building,
limited public access
.Apartment buildings
.Open public access
400, 620, 640
885
Continuous
Duty
620, 640, 885
Continuous
Duty
Class
.No public access
.Prison related
Parameter
Model 402
Standard
Application
Single family residence, single leaf or bi-parting gate
(vehicles only, not for pedestrian use)
(not recommended for solid gates)
Cycles per hour
30
30
Maximum gate
swing
90 degrees
90 degrees
90 degree
opening time
12 seconds
12 seconds
Maximum weight
per gate leaf
900 pounds
(410 kg)
900 pounds
(410 kg)
Maximum length
per gate leaf
10 feet (3 m)
10 feet (3 m)
Approx. operating
temperature range
-33oF to 165oF (-36oC to 74oC)
(For extreme temperature conditions,
arctic grade fluid is available upon request)
Hydraulic locking
Available in
opened or
closed positions
Voltage
115 VAC (2.5 A) or 230 VAC (1.5 A)
security
Duty Cycle
The duty cycle achieved by a swing gate operator
in terms of "operations per hour" is, in large part,
a function of the installation. For example, an
operator swinging a leaf through 125o will be able
to complete fewer operations per hour than the
same operator swinging only 90o.
The duty cycles listed below reflect performance
at an ambient temperature of 72o F (22o C) and
at normal voltages of 115 or 230 VAC. Changes
in environmental conditions, voltage and gate
condition will affect achievable duty cycle.
FAAC Operator Model
400
402
412
422
750
760
Specifications
Cycles per hour
80
30
50
30
30
30
Model 422
Standard
Available in
opened and/or
closed positions
Note: Operator specifications are approximate. Environmental factors can change the
performance of the operator. Your installer will advise you which model of operator will
work best for your site and application.
Speed and leaf length
Some thought should be given to the speed at which the gate will travel.
The longer the gate leaf, the faster the traveling edge must move to clear
an area in a given amount of time.
Model 450 MPS Control Panel and
fiberglass enclosure (cover not shown)
402 Dimensions
m)
m)
9c
.8 c
95.
(71
n. (
in.
5i
7
6
.
2
37
26.
Examples illustrating the relationship between operator speed, gate leaf
length, and the velocity of the leaf’s traveling edge
3.2
(8.5 6 in.
cm)
.
9 in
9.3 cm)
(24
2.38
in. (6
.1
cm)
)
m)
cm
.7 c
9.3
(98
. (6
in.
n
i
8
8
25
38.
27.
n
8i
9.8 4 cm)
(2
422 Dimensions
2.38
in. (6
.1
cm)
A speed of 40 feet/minute (12.2 meters/minute) is a “bench mark” velocity.
It permits efficient operation while limiting the energy in the moving gate leaf.
The lower the energy, the less chance of damage to property or injury to
people in the event of accidental contact with the moving gate.
3.2
(8.5 6 in.
cm)
4.3
(11.3 9 in.
cm)
Speed options available
(time needed to swing a
gate 90o)
EXAMPLE:
Velocity of the traveling
edge of an 8 ft (2.4 m) leaf
[in feet/m and (meters/m)]
Longest leaf which can be
used if the velocity of the
traveling edge is not to
exceed 40 fpm (12.2 mpm)
6 sec.
126 fpm (38 mpm)
2.5 ft (0.8 m)
12 sec.
63 fpm (19 mpm)
5 ft (1.5 m)
15 sec.
50 fpm (15 mpm)
6 ft (1.9 m)
17 sec.
44 fpm (14 mpm)
7.5 ft (2.3 m)
23 sec.
33 fpm (10 mpm)
10 ft (3 m)
Model 402 and 422
How many degrees of
swing are required?
Mounting Geometry
Sometimes the mounting measurements will result in a flush mounting. Other applications require
a column to be notched in order to accommodate the correct mounting geometry.
Note: If, in your installation, notching a column is not practical, other solutions are available:
. Install operators using an outward swing.
. Upgrade to an operator with more mounting flexibility.
. Use a Pantograph.
. Use an in-ground operator.
Notched
column
. One FAAC gate operator (Model 750)
can swing a gate up to 180o.
. All models of FAAC operators can
swing a gate at least 90o.
. Openings which require swings
.
greater than 90o will need certain
FAAC operator models.
The swing of an operator applies
equally to inward or outward
swinging gates.
Drive
90o
Flush mounting
Notched mounting
Decisions regarding mounting geometry apply to gate mounted operators:
Models 400, 402, 422 and 412 .
As shown in the diagrams below, the operators must be mounted at an angle to the gate.
Correct mounting geometry assures that the desired degrees of swing are achieved, that the gate
speed is correct, and that the operator and gate will operate properly and have a long life.
Street
All FAAC operators:
Models 412, 402, 422, 400,
750, 760
Drive
Mounting dimensions for
OUTWARD-swinging 402
operators, top view
Dimensions
A
4.5 in. (11.4 cm)
B
4.5 in. (11.4 cm)
C
26.5 in. (67.3 cm)
E
MUST be less than A
Mounting dimensions for
INWARD-swinging 402
operators, top view
Dimensions
A
4.5 in. (11.4 cm)
B
4.5 in. (11.4 cm)
C
35.5 in. (90.2 cm)
D
If greater than 2 in. (5cm)
110o
Street
Models 412, 400, 750, 760.
Drive
115
o
Street
Models 400, 750, 760.
construct a recess liner.
E
MUST be less than A
Drive
Mounting dimensions for
OUTWARD-swinging 422
operators, top view
125o
Dimensions
A
4.75 in. (12 cm)
B
4.75 in. (12 cm)
C
27 in. (68.6 cm)
E
MUST be less than A
Street
Models 400 EG
(extended geometry),
750, 760.
Mounting dimensions for
INWARD-swinging 422
operators, top view
Dimensions
A
4.75 in. (12 cm)
B
4.75 in. (12 cm)
C
36.63 in. (93 cm)
D
max 2.75 in. (7 cm)
E
MUST be less than A
Drive
140o
Street
Models 750 (up to 180o),
760 (up to 148o
with “soft stop”)
HEADQUARTERS
Bologna, Italy
RESEARCH & DEVELOPMENT
Bologna, Italy
Dublin, Ireland
FAAC’s U.S.
headquarters
in Cheyenne,
Wyoming
PRODUCTION FACILITIES
Bologna, Italy
Founded in 1965, FAAC has risen to become
the world’s largest specialized manufacturer
SUBSIDIARY OFFICES
Wals-Siezenheim, Austria
Corbas-Lyon, France
Freilassing, Germany
Alcobendas-Madrid, Spain
Illnau, Switzerland
Basingstoke, Hampshire, U.K.
Cheyenne, Wyoming, U.S.A.
of automated operators for swing, slide and
barrier gate systems.
International company headquarters, research
& development and primary production facilities
are located in Bologna, Italy. Dublin, Ireland is the
site of FAAC’s research, design and production

facility for electronic controls including photocells,
radio controls and code opening systems.
INTERNATIONAL, INC.
FAAC is an ISO 9001 Certified Company
FAAC International, Inc.
303 Lexington Avenue
Cheyenne, WY 82007
1-800-221-8278
Fax: (307) 632-8148
Web: www.faacusa.com
LIT-402/422REV-01/02
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising