CAL. Z46G MECHANICAL WATCHES ENGLISH ● Automatic winding ● Time and date calendar ● Power reserve indicator DISPLAY AND CROWN/BUTTONS Power reserve hand Minute hand Click button Hour hand E V R RES E 0 9 10 2 0 10 3 4 English ER 2 40 PO 30 AUTOMATIC 7 a: Normal position W 8 8 Second hand 2 A 12 1 11 21 Jewels 6 5 b: First click a b CROWN Date HOW TO START THE WATCH ● This is an automatic-winding mechanical watch. To initially start your watch: Swing it from side to side in a horizontal arc for about 30 seconds, to start the second hand moving. English * If the watch is worn on the wrist, the mainspring will be wound automatically through normal wrist movement. 3 SCREW DOWN CROWN [for models with screw down crown] Unlocking the crown 1 Turn Crown counterclockwise until you no longer feel the threads turning. English 2 Crown can be pulled out. Locking the crown 1 Push Crown back in to normal position. 2 Turn Crown clockwise while pressing it lightly until tight. 4 TIME / CALENDAR SETTING Setting the time and adjusting the date Hour hand Minute hand 1 ➠ E V R RES E 0 9 10 ER 2 40 PO W 30 2 0 10 2 ➠ 1 Press the click button and set it to the date of a previous day. 3 CROWN 3 AUTOMATIC 7 21 Jewels 6 5 ➠ 8 4 8 4 Date Second hand 2 Pull out the crown. (The second hand does not stop.) English 12 1 11 A 3 Turn the crown clockwise until you reach the today’s date. * Advance the hand further and set it to the current time. 4 Press in the crown to the normal position. 5 POWER RESERVE INDICATOR E V R RES E 2 ER 0 W 30 2 0 10 3 8 4 8 AUTOMATIC 7 6 PO 9 10 12 1 11 40 English Power reserve hand 21 Jewels 6 5 The power reserve indicator shows the amount the watch is wound as an amount of time, so you can see how long the watch will run at a glance. The power reserve hand indicates the remaining amount. The time pointed to by the power reserve hand is the remaining amount of time. NOTES ON OPERATING THE WATCH TIME/CALENDAR SETTING English ● Do not set the date between 9:00 p.m. and 2:00 a.m. Otherwise, it may not change properly. * If it is necessary to set the date during that time period, first change the time to any time outside it, set the date and then reset the correct time. ● When setting Hour hand, check that AM/PM is correctly set. * The watch is so designed that the date changes once in 24 hours. Turn the hands past the 12 o’clock marker to determine whether the watch is set for the A.M. or P.M. period. If the date changes, the time is set for the A.M. period. If the date does not change, the time is set for the P.M. period. ● When setting Minute hand, be sure to turn back the hands a little behind the desired time and then advance them to the exact time. ● It is necessary to adjust the date at the end of February and 30-day months. AUTOMATIC WINDING ● This is an automatic winding mechanical watch and cannot be wound manually. ● This watch will run approximately 40 hours after it is fully wound. If it is not wound enough, the watch may lose time. In order to maintain the watch’s accuracy, we recommend wearing the watch at least 8 hours a day. 7 English POWER RESERVE INDICATOR 8 ● The remaining time shown is only an approximation. The time shown may be different from actual remaining time. This product has an automatic-winding system which comes with a power reserve indicator function. The mainspring will be automatically wound by your natural arm movements while you wear it on your wrist. The power reserve hand is pointing to the fully-wound position (40H). The amount the watch is wound will change with the frequency of your arm movements and the amount of time you wear the watch, so the hand will not always point to the fully-wound position. If you remove the watch from your arm and do not wind manually, the power reserve hand will move toward zero as time passes. SPECIFICATIONS ● Vibration ● Loss/Gain ● Jewels : 21,600 Oscillations / 1hr : Within +25 and –15 second (Daily Rate)* : 21 Jewels English * The mechanism of mechanical watches is very precise and delicate. Time accuracy may change depending of which direction the watch faces. Therefore, any actual loss/gain may not fall within the range of time accuracy specified above, and depends on the condition of use, such as the length of time during which the watch is worn on the wrist, temperature, affection of strong magnetism, vibration like motorcycles or chain saws, life style (whether much arm movement is involved or not), whether the watch is wound up fully or not, etc. 9 TO PRESERVE THE QUALITY OF YOUR WATCH WATER RESISTANCE ● Water resistance (5 bar)* English If “WATER RESISTANT 5 BAR” ● Non-water resistant is inscribed on the case back, your If “WATER RESISTANT” is not watch is designed and manuinscribed on the case back, your 5 bar WR factured to withstand up to 5 bar watch is not water resistant, and care should be taken not to get it and is suitable for swimming, yachting and taking wet as water may damage the movement. If a shower. the watch becomes wet, we suggest that you ● Water resistance (10 bar/15 bar/20 bar)* have it checked by an AUTHORIZED PULSAR If “WATER RESISTANT 10 BAR”, DEALER or SERVICE CENTER. “WATER RESISTANT 15 BAR” 10/15/20 or “WATER RESISTANT 20 BAR” ● Water resistance (3 bar) bar WR is inscribed on the case back, If “WATER RESISTANT” is inscribed on the case back, your watch is your watch is designed and manufactured to designed and manufactured to withstand up to 10 bar/15 bar/20 bar and is withstand up to 3 bar, such as acci- suitable for taking a bath, shallow diving, but not dental contact with splashes of water or rain, but it is for scuba diving. We recommend that you wear a 10 not designed for swimming or diving. PULSAR Diver’s watch for scuba diving. * Before using the water resistance 5, 10, 15 or 20 bar watch in water, be sure the crown is pushed in completely. Do not operate the crown when the watch is wet or in water. If used in sea water, rinse the watch in fresh water and dry it completely. * When taking a shower with the water resistance 5 bar watch, or taking a bath with the water resistance 10, 15 or 20 bar watch, be sure to observe the following: • Do not operate the crown when the watch is wet with soapy water or shampoo. • If the watch is left in warm water, a slight time loss or gain may be caused. This condition, however, will be corrected when the watch returns to normal temperature. TEMPERATURES +35°C +5°C Your watch works stably within a temperature range of 5°C and 35°C (41°F and 95°F). Do not leave your watch in very low or high temperatures. English NOTE: Pressure in bar is a test pressure and should not be considered as corresponding to actual diving depth since swimming movement tends to increase the pressure at a given depth. Care should also be taken on diving into water. MAGNETISM N S Your watch will be adversely affected by strong magnetism. Keep it away from close contact with magnetic objects. 11 CARE OF CASE AND BRACELET PERIODIC CHECK English To prevent possible rusting It is recommended that the of the case and bracelet watch be checked once every caused by dust, moisture and 2-3 2 to 3 years. Have your Years perspiration, wipe them watch checked by an periodically with a soft dry AUTHORIZED PULSAR cloth. DEALER or SERVICE CENTER to ensure that the case, crown, buttons, gasket and SHOCKS crystal seal remain intact. Light activities will not affect your watch, but be sure to take the watch off your wrist when you engage in strenuous sports. Also be careful not to drop your watch on the floor. CHEMICALS 12 Be careful not to expose the watch to solvents, mercury, cosmetic spray, detergents, adhesives or paints. Otherwise, the case, bracelet, etc. may become discolored, deteriorated or damaged. PRECAUTION REGARDING CASE BACK PROTECTIVE FILM If your watch has a protective film and/or a sticker on the case back, be sure to peel them off before using your watch.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project