PG5908/PG5916 Series Industrial Protocol

PG5908/PG5916 Series Industrial Protocol
Industrial Protocol Gateway
PG5908/PG5916 Series
Feature Highlights

Dual 10/100Mbps Ethernet for networking redundancy

Remotely monitor, manage, and control industrial field devices

Relay out indicator for Network link-status

LCM display with 4-key touch pad for configuration

Same hardware platform for different protocol conversion (Modbus TCP/RTU/ASCII, DNP3.0 TCP
or serial, IEC 60870-5-101, IEC 60870-5-103, IEC 60870-5-104, IEC 61850)

User friendly configuration with a Java-Based Windows utility
Product Description
The PG5908/PG5916 Series is a highly reliable and fault tolerant Industrial Protocol Gateway. Its powerful
architecture provides seamless conversion between the different protocols Ethernet or Serial based. The
serial devices communicating on different protocols could be integrated into the system and extend its
reach over the gateway’s redundant Ethernet. This device is designed to work in most demanding
industries such as power substations, power generation, oil and gas, farming and manufacturing.
The configuration carried out through a use friendly, Java- Based Windows Utility called eNode Designer. It
allows configuring target platforms, set device properties and protocol data point mapping. To do so, a
project file representing the system should be created. This will include devices and the protocol
applications running on them. The configuration is completely dependent on the “eNode Module” which
represents that device or application – but may include things such as changing the communication port
settings and defining where data point information enters and leaves the eNode Designer system.
Atop Technologies, Inc.
TEL: +886-3-5508137
FAX: +886-3-5508131
sales@atop.com.tw
http://www.atop.com.tw
Design and specification are subjected to change without notice.
All product names referenced herein are registered trademarks of their respective companies.
V0.1
Application
Features
The protocol gateway’s embedded protocol stacks allow
Seamless conversion
Exception/error Management
Unsolicited event management for the protocols requiring them (such as DNP3)
High performance
Low cost
General Architecture
* Protocol A and Protocol B - Please refer to Protocol Availability Matrix and order information
Atop Technologies, Inc.
TEL: +886-3-5508137
FAX: +886-3-5508131
sales@atop.com.tw
http://www.atop.com.tw
Design and specification are subjected to change without notice.
All product names referenced herein are registered trademarks of their respective companies.
V0.1
Example
The example shows how to Easily connect a Modbus Serial HMI, through Atop’s Protocol Gateway to a DNP3.0
Ethernet slave IED. The host HMI has the role of a Modbus Serial Master while the end-device to be accessed is
a DNP3.0 Ethernet Server.
Atop’s protocol Gateway acts towards the HMI seamlessly as a Modbus Serial Slave, answering the poll
commands or the write commands required by the Host by its virtual Modbus ID. Meanwhile, it acts as a
DNP3.0 Ethernet Client with regard to the end-device whose DNP3.0 address is mapped to the virtual Modbus
ID that the HMI is accessing.
Be careful! – all gateway functions listed in the datasheet refer to the “Gateway” role, and not which “host” or
“slave” the gateway is connected to. In this example, the SKU shown is “MBSS-DNEC” (Modbus Serial Slave to
DNP3.0 Ethernet Client)
Protocol Availability Matrix for PG5908/PG5916 Series
Protocol A
Ethernet Server
Protocol B
Ethernet
Client
Serial Slave
Modbus IEC 60870TCP
5-104
IEC 61850
DNP3
IEC 61850
n/a
n/a
n/a
n/a
DNP3
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
50ESDNSM
50ESMBSM
50ES01SM
50ES03SM
DNESDNSM
DNESMBSM
DNES01SM
DNES03SM
MBESDNSM
04ESDNSM
04ESMBSM
04ES01SM
04ES03SM
DNSSDNSM
DNSSMBSM
DNSS01SM
DNSS03SM
Modbus
TCP
IEC 608705-104
DNP3
Modbus
Serial RTU/ASCII
Master IEC 608705-101
IEC 608705-103
n/a
MBES01SM
MBES03SM
DNP3
Modbus IEC 60870- IEC 60870RTU/ASCII
5-101
5-103
n/a
n/a
n/a
n/a
DNSSDNEC
DNSSMBEC
MBSSDNEC
n/a
n/a
n/a
n/a
n/a
n/a
n/a
01SSDNSM
01SSMBSM
03SSDNSM
03SSMBSM
03SS01SM
MBSS04EC
MBSSDNSM
n/a
MBSS01SM
MBSS03SM
n/a
01SS03SM
n/a
Atop Technologies, Inc.
TEL: +886-3-5508137
FAX: +886-3-5508131
sales@atop.com.tw
http://www.atop.com.tw
Design and specification are subjected to change without notice.
All product names referenced herein are registered trademarks of their respective companies.
V0.1
Protocol Specifications
IEC61850 Server/ Client
Supported
Functions
Supported
Control Type
of commands
Implemented
Protocol
Subsets
 Generic access to the data
(Read, Write)
 Clock Synchronization
 8 Logical Devices per Port
 GOOSE (Generic Object Oriented
Substation Event) – a GOOSE
message will be generated by the
gateway automatically upon
event(*)
(*)Being other protocols not RealTime, there is no guarantee that
GOOSE message is generated within
1 ms from the event itelf.
 Direct-with-Normal-Security
Select Before Operate (SBO)-withNormal-Security
 Direct-with-Enhanced Security
Select Before Operate (SBO)with-Enhanced-Security
 IEC 61850-6 (Substation
Configuration Language
Description: SCL)
 IEC 61850-7-1 (Principles and
Models)
 IEC 61850-7-2 (Abstract
Communication Service
 Interface: ACSI
 IEC 61850-7-3 (Common Data
Classes: CDC)
 IEC 61850-7-4 (Logical Nodes and
data Object Classes)
 IEC 61850-8-1 (Mapping to
Manufacturing Message
Specification: MMS)
 Edition 1 & Edition 2 are both
Supported
DNP3 Server/ Client/ Master/ Slave
General
 Serial Mode or Ethernet with TCP or
Specifications
UDP Mode
 Server side supports serving up to 5
client in TCP Mode
 Client side in a single RS-485 port,
supports connecting up to 16 IEDs
 Client side supports connecting up to
16 IEDs
 Maximum Fragment size 2048 octets
 Protocol implementation with
configurable parameters conforms to
IEEE Std 1815-2012 level 2
Supported
Functions
Supported
DNP3 Object
Library
 Time Synchronization generic access to
the data(Read, Write)
 Commands with or without
preselection (Select, Operate, Direct
Operate)
 Transmission of time-tagged events
 Counter management (Immediate
Freeze, Freeze and Clear)
 Self-address
 Binary Inputs up to 8000 pts
 Binary Outputs up to 2000 pts
 Double Inputs up to 4000 pts
 Analog Inputs up to 250 pts
 Analog Outputs up to 250 pts
 Counters up to 250 pts
Atop Technologies, Inc.
TEL: +886-3-5508137
FAX: +886-3-5508131
sales@atop.com.tw
http://www.atop.com.tw
Design and specification are subjected to change without notice.
All product names referenced herein are registered trademarks of their respective companies.
V0.1
Modbus Server/ Client/ Master/ Slave
IEC 60870-5-101 Master/ Slave
General
 Support Modbus RTU and ASCII in
Specifications
Serial mode
 Support Modbus in TCP mode
 For Modbus Client in TCP mode,
support connecting up to 64
Modbus servers
 For Modbus Server in TCP mode,
support serving up to 64 Modbus
clients
 Support maximum number of
data points in read direction: 8000
pts
 Support maximum number of
commands in write direction:
4000 pts
Supported
1: Read Coils
Function
2: Read Discrete Inputs
Codes
3: Read Holding Registers
4: Read Input Registers
5: Write Single Coil
6: Write Single Register
15: Write Multiple Coils
16: Write Multiple Registers
43/14: Read Device Identification
(server side only)
Supported
1: illegal function
Exception
2: illegal data address
Codes
3: illegal data value
4: server device failure
6: server device busy
General
 Protocol implementation with
Specifications
configurable parameters conforms to
the IEC 60870-5-101 edition 2
specification
 Process Information in Monitor and
Control Direction
 Balanced and Unbalanced Modes
 CP24Time2a or CP56Time2a timestamp
for monitor direction report
Supported
Functions




Supported
Data Types
 Monitors Points:
Each supports up to 1000 pts: Single
Point, Double Point, Step Position, Bit
String, Measured with Normalized Value,
Measured with Scaled Value, Measured
Short Floating Point Value, Integrated
Totals
 Control Points:
Each supports up to 500 pts: Single
Command, Double Command, Regulating
Step Command, Set Point Command with
Normalized Value, Set Point Command
with Scaled Value, Set Point Command
Short Floating Point, Bit string
Station Initialization
Interrogation
Read Procedure
Cyclic Data and Spontaneous
Transmission (Slave Side only)
 Clock Synchronization
 Transmission of Integrated Totals
 Direct and SBO command
Atop Technologies, Inc.
TEL: +886-3-5508137
FAX: +886-3-5508131
sales@atop.com.tw
http://www.atop.com.tw
Design and specification are subjected to change without notice.
All product names referenced herein are registered trademarks of their respective companies.
V0.1
IEC 60870-5-103 Master/ Slave
IEC 60870-5-104 Server/ Client
General
General
 Protocol implementation with
 Server side supports serving up to 5
Specifications
Specifications
configurable parameters conforms
client
to the IEC 60870-5-103:1997
 Client side supports connecting up to
 Master supports connecting up to
10 IEDs
16 IEDs
 Protocol implementation with
configurable parameters conforms to
 Process Information in Monitor
and Control Direction
the IEC 60870-5-104 specification
edition 2
 Unbalanced Modes
 Process Information in Monitor and
Control Direction
 CP56Time2a timestamp for Control
Commands
Supported
 Station Initialization, Supports Supported
 Station Initialization
Functions
Functions
reset FCB and CU
 Interrogation
 General Interrogation
 Read Procedure (Server side only)
 Clock Synchronization
 Cyclic Data and Spontaneous
 Command Transmission
Transmission (Server side only)
 Test Mode
 Clock Synchronization
 Blocking of Monitor Direction
 Transmission of Integrated Totals
 Direct and SBO command
Supported
Supported
 Monitor direction:
 Monitors Points:
Information
Data Types
Each supports maximum 1000 pts: Single
 Status indications in monitor
Point, Double Point, Step Position, Bit
direction: from <16> to <30>
String, Measured with Normalized Value,
 Supervision indications in monitor
Measured with Scaled Value, Measured
direction: <32>, <33>, from <35>
Short Floating Points Value, Integrated
to< 39>, <46>, <47>
Totals.
 Earth fault indications in monitor
 Control Points:
direction: from <48> to <52>
Each supports maximum 500 pts: Single
 Fault indications in monitor
Command, Double Command, Regulating
direction: from <64> to <93>
Step Command, Set Point Command with
 Auto-reclosure indications in
Normalized Value, Set Point Command
monitor direction: from <128> to
with Scaled Value, Set Point Command
<130>
Short Floating Point, Bitstring.
 Measurands in monitor direction:
 Event Logging (Server Side only)
from <144> to <148>
Universal Event Buffer up to 20,000
 Control direction:
Events
General commands in control
direction: from <16> to <19>, from
<23> to <26>
Atop Technologies, Inc.
TEL: +886-3-5508137
FAX: +886-3-5508131
sales@atop.com.tw
http://www.atop.com.tw
Design and specification are subjected to change without notice.
All product names referenced herein are registered trademarks of their respective companies.
V0.1
Hardware Specifications
Network Interface
Ethernet Port
LAN Mode
Compliance
2 x RJ-45
Dual Subnets or LAN Redundancy
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-T(X)
Serial Interface
Connector
Port
Mode
Baud Rate
Parity
Data Bits
Stop Bits
Flow Control
RJ-45
8 or 16
RS-232/422/485, software selectable
50~921,600 bps
None, Odd, Even, Space, Mark
5,6,7,8
1,2
None, Xon/Xoff, RTS/CTS (RS-232 only)
Power Characteristics
Connector
Input Voltage
Power Consumption
Power Redundancy
Reverse Polarity Protection
IEC 60320-1 C14 AC Power Inlet (AC models)
5.08mm 3-pin Lockable Terminal Block (DC models)
24-48 VDC for DC models
100-240 VAC for AC models
0.54A @ 24 VDC
0.21A @ 100 VAC
No
Yes (DC Input only)
Mechanicals
Housing
Dimensions(W x H x D)
Installation
Reset Button
Weight
IP30 protection, metal housing
436 mm x 43.5 mm x 200 mm
19” Rack Mount
Yes
3.2kg (16 ports) / 3.0 kg ( 8 ports)
Environmental Limits
Operating Temperature
Storage Temperature
Ambient Relative Humidity
-20°C ~ 70°C (-4°F ~ 158°F)
-40°C ~ 85°C (-40°F ~ 185°F)
5 ~ 95% RH, (non-condensing)
Software
Protocols
IPv4, ARP, ICMP, TCP, UDP, DHCP Client, DNS Client, Telnet, HTTP, SNMP v1/v2c,
Syslog
Atop Technologies, Inc.
TEL: +886-3-5508137
FAX: +886-3-5508131
sales@atop.com.tw
http://www.atop.com.tw
Design and specification are subjected to change without notice.
All product names referenced herein are registered trademarks of their respective companies.
V0.1
Regulatory Approvals
Safety
EMC
Test
IEC 61000-4-2
EN 60950-1/IEC60950-1 LVD
FCC Part 15, Subpart B, Class B
EN 55022, Class B
EN 61000-3-2
EN 61000-3-3
EN 55024
Item
ESD
Contact Discharge
Air Discharge
Enclosure
AC Power Port
DC Power Port
Signal Port
AC Power Port
AC Power Port
DC Power Port
DC Power Port
Signal Port
AC Power Port
DC Power Port
Signal Port
Enclosure
AC Power Port
IEC 61000-4-3
IEC 61000-4-4
RS
EFT
IEC 61000-4-5
Surge
IEC 61000-4-6
CS
IEC 61000-4-8
IEC 61000-4-11
Shock
Drop
Vibration
RoHS
MTBF
Warranty
PFMF
DIP
IEC60068-2-27
ISTA Test Procedure 2A
IEC60068-2-64
Yes
TBD
5 years
Value
±8KV
±15KV
10 V/m
±4.0KV
±4.0KV
±2.0KV
Line-to Line±2.0KV
Line-to Earth±4.0KV
Line-to Line±1.0KV
Line-to Earth±2.0KV
Line-to Line±2.0KV
10 Vrms
10 Vrms
10 Vrms
1A/m
-
Level
4
4
3
4
4
3
4
4
3
3
4
3
3
3
3
-
Ordering Information
Hardware
PG5916-N-DC
PG5916-N-US
PG5916-N-EU
PG5908-N-DC
PG5908-N-US
PG5908-N-EU
Ind. 16-Port Protocol Gateway, RS-232/422/485 Software Selectable, DC TB3
Ind. 16-Port Protocol Gateway, RS-232/422/485 Software Selectable, AC Inlet, US Plug
Ind. 16-Port Protocol Gateway, RS-232/422/485 Software Selectable, AC Inlet, EU Plug
Ind. 8-Port Protocol Gateway,RS-232/422/485 Software Selectable, DC TB3
Ind. 8 Port Protocol Gateway, RS-232/422/485 Software Selectable, AC Inlet, US Plug
Ind. 8 Port Protocol Gateway, RS-232/422/485 Software Selectable, AC Inlet, EU Plug
Atop Technologies, Inc.
TEL: +886-3-5508137
FAX: +886-3-5508131
sales@atop.com.tw
http://www.atop.com.tw
Design and specification are subjected to change without notice.
All product names referenced herein are registered trademarks of their respective companies.
V0.1
Optional Accessories
Model Name
SDR-75-24
Part Number
50500752240001G
Power Adapter-AD17-24C
(US-Y)
Power Adapter-AD17-24D
(EU-Y)
GDC-120
ADP-DB9(F)-TB5
CBL-RJ45(8P)-DB9(M)-90
CBL-RJ45(8P)-DB9(M)-200
CBL-RJ45(8P)-DB9(F)-90
CBL-RJ45(8P)-DB9(F)-90-C
CBL-RJ45(8P)-DB9(F)-200-C
RMK-718-Black
Power Cable (US)
Power Cable (EU)
Fuse
50500151240002G
50500151240012G
59906861G
59906231G
50891781G
50891951G
50891791G
50891971G
50891961G
70100000000040G
50801041G
50801051G
59907561G
Description
75W/3.2A DIN-Rail 24VDC power supply 88~264VAC / 124370VDC input
Y-Type power adaptor,100-240VAC input, 0.6A @ 24VDC
output, US plug
Y-Type power adaptor,100-240VAC input, 0.6A @ 24VDC
output, EU plug
120mm copper woven grounding cable
Female DB9 to Female 3.81mm TB5 Converter
RJ45 to DB9 Male Cable, 90cm
RJ45 to DB9 Male Cable, 200cm
RJ45 to DB9 Female Cable, 90cm
RJ45 to DB9 Female Cross Over Cable, 90cm
RJ45 to DB9 Female Cross Over Cable, 200cm
Rack Mount Mounting-Kit, Black
6 feet Power Cable, US
6 feet Power Cable, EU
250V, 2A, 20mm (length) * 5mm (diameter)
Protocols
04ES-01SM
04ES-DNSM
04ES-MBSM
DNES-01SM
DNES-DNSM
DNES-MBSM
DNSS-DNEC
DNSS-MBEC
MBES-01SM
MBES-DNSM
MBSS-04EC
MBSS-DNEC
01SS-DNSM
01SS-MBSM
DNSS-01SM
DNSS-DNSM
DNSS-MBSM
MBSS-01SM
MBSS-DNSM
04ES-03SM
50ES-01SM
50ES-03SM
50ES-DNSM
IEC 60870-5-104 Ethernet Server to IEC 60870-5-101 Serial Master
IEC 60870-5-104 Ethernet Server to DNP3 Serial Master
IEC 60870-5-104 Ethernet Server to Modbus Serial Master
DNP3 Ethernet Server to IEC 60870-5-101 Serial Master
DNP3 Ethernet Server to DNP3 Serial Master
DNP3 Ethernet Server to Modbus Serial Master
DNP3 Serial Slave to DNP3 Ethernet Client
DNP3 Serial Slave to Modbus Ethernet Client
Modbus Ethernet Server to IEC 60870-5-101 Serial Master
Modbus Ethernet Server to DNP3 Serial Master
Modbus Serial Slave to IEC 60870-5-104 Ethernet Client
Modbus Serial Slave to DNP3 Ethernet Client
IEC 60870-5-101 Serial Slave to DNP3 Serial Master
IEC 60870-5-101 Serial Slave to Modbus Serial Master
DNP3 Serial Slave to IEC 60870-5-101 Serial Master
DNP3 Serial Slave to DNP3 Serial Master
DNP3 Serial Slave to Modbus Serial Master
Modbus Serial Slave to IEC 60870-5-101 Serial Master
Modbus Serial Slave to DNP3 Serial Master
IEC 60870-5-104 Ethernet Server to IEC 60870-5-103 Serial Master
IEC 61850 Ethernet Server to IEC 60870-5-101 Serial Master
IEC 61850 Ethernet Server to IEC 60870-5-103 Serial Master
IEC 61850 Ethernet Server to DNP3 Serial Master
Atop Technologies, Inc.
TEL: +886-3-5508137
FAX: +886-3-5508131
sales@atop.com.tw
http://www.atop.com.tw
Design and specification are subjected to change without notice.
All product names referenced herein are registered trademarks of their respective companies.
V0.1
50ES-MBSM
DNES-03SM
MBES-03SM
01SS-03SM
03SS-01SM
03SS-DNSM
03SS-MBSM
DNSS-03SM
MBSS-03SM
IEC 61850 Ethernet Server to Modbus Serial Master
DNP3 Ethernet Server to IEC 60870-5-103 Serial Master
Modbus Ethernet Server to IEC 60870-5-103 Serial Master
IEC 60870-5-101 Serial Slave to IEC 60870-5-103 Serial Master
IEC 60870-5-103 Serial Slave to IEC 60870-5-101 Serial Master
IEC 60870-5-103 Serial Slave to DNP3 Serial Master
IEC 60870-5-103 Serial Slave to Modbus Serial Master
DNP3 Serial Slave to IEC 60870-5-103 Serial Master
Modbus Serial Slave to IEC 60870-5-103 Serial Master
Atop Technologies, Inc.
TEL: +886-3-5508137
FAX: +886-3-5508131
sales@atop.com.tw
http://www.atop.com.tw
Design and specification are subjected to change without notice.
All product names referenced herein are registered trademarks of their respective companies.
V0.1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising