GB-short 891365A TCH-digital modules

GB-short 891365A TCH-digital modules
TRIAX TCH
Compact Headend
TCSD Digital Modules (QPSK/PAL- SECAM)
Installation and User Manual
896365A
05-2001
1
UK
TCSD Modules
The modules for receiving digital programs
(DVB-S) have been designed to fit into an analog TCH system, so that a mix of analog and
digital modules is possible in the same system.
Due to the fact that digital receiving modules
need more space, it is necessary to use 2 modules occupying 2 TCH slots to receive digital
programs.
The first module in the system is similar to the
analog modules of the TCH sat receiver, where
the analog sat receiver is replaced by a DVB-S
receiver, and the 15P D-SUB connector is replaced by a 34P IDC connector. This connector is for I2C control, TS output and A/V input
to/from the MPEG2/CI module.
The second module in the system consists of
2 pc boards: A MPEG2 decoder pc board and
a Common Interface pc board, which is
mounted on the MPEG2 decoder pc board. On
the Common Interface pc board is a 34P IDC
connector, which is for I2C control, TS input and
A/V output from/to the DVB-S receiver pc board.
If conditional access is needed to receive the
program, a PC card module from the program
provider is to be inserted the PC card connector on the Common Interface pc board.
TCSD 661 =
TCSD 662 =
TCSD 663 =
TCSD 664 =
TCSD 641 + TCSD 651.
TCSD 642 + TCSD 651.
TCSD 643 + TCSD 651.
TCSD 644 + TCSD 651.
#
1
#
2
#
3
#
4
#
5
TCSD 661
TCSD 661
TCSD 661
The 2 modules are connected by means of the
34P IDC cable.
TCSD 641
DVB-S / DSB multi standard
VHF mono.
TCSD 642
DVB-S / DSB multi standard
UHF mono.
TCSD 643
DVB-S / DSB multi standard
VHF stereo.
TCSD 644
DVB-S / DSB multi standard
UHF stereo.
TCSD 651
DVB-MPEG2 / CI.
TCSA 631
Example:
TCSA 618
The 2 modules for receiving digital programs
(e.g. TCSD661 consisting of TCSD641 +
TCSD651) must be placed besides each other
with the TCSD 651 in the highest slot number.
#
6
#
7
#
8
Module Slot No.
TV Standard
The TV standard is programmed on the DIPSW on TCSD 641/2/3/4 as shown in the figure
below. Settings of the DIP-SW also control the
video standard of the MPEG2 decoder, so that
at the same time it is set to correct PAL or
Secam standard.
Note: The modules are pre-set for system B/G
(PAL). All other parameters are set by means
of the keyboard and at the same time stored in
the memories in the System Control and
MPEG2 decoder.
Receiver module
DIP SWITCH
The Dip Switch is set according to TV-standard as shown in the figure below.
TV standard. Dip-sw.
B/G
1=ON 2=ON
I (PAL) 1=OFF 2=ON
L (Secam) 1=ON 2=OFF
D/K (PAL)1=OFF 2=OFF
MPEG 2 + CI Module
Country
Europe, others
UK
France
Eastern, Europe
ON
On
Off
1
2
2
Replacement of module:
Features
Digital satellite module:
• Input frequency range: 920-2150 MHz.
• Output frequency range: 175-350 MHz
(490641/3)
• Output frequency range: 470-862 MHz
(490642/4)
• AFC control.
• Programmable LNB control:
0/14/18V - 0/22kHz.
• Input modulation: QPSK.
• Compliant with PI DVB/MPEG2 Transport
Streams (EN 50083-9).
• Programmable multi standard system
(DIP-SW).
• A2 Stereo/Dual mode (490643/4).
• µ-processor control with PLL-tuning
of sat-tuner and modulator.
• Compliant with Common Interface Specification for Conditional Access (EN 50221)
• Fully DVB/MPEG2 compliant: Main profile/
main level.
• Output video norm: Pal/Secam.
• Teletext: Reinserted in VBI.
• Software downloading through RS232.
• Easy installation and operation.
• Easy servicing.
SW
• Check that the software version number
printed on the label of the module
(e.g. SW. 1.1) is lower or equal to the
version number which is shown shortly in
the display at power-on.
• Check that the module is set at the TV
standard wanted
(see programming of TV standard).
• Place the module in the Basic Unit and
finally programme the module.
n
sio
ver
re
a
w
oft
=S
When changing from one module to another
similar module, the modulator set-up is not
changed, but the MPEG/CI module is changed
in the MPEG flash memory.
When replacing a module of another type,
problems of placing the output channel may
arise. The system control will automatically
allocate the next vacant channel to the module.
If problems arise when placing a new module,
the display will show an error code at poweron.
Causes and a detailed explanation of the
different error codes are shown in a table on
the programming schema.
Contact your dealer if you need an upgrade of
the software.
Programming:
When the equipment is switched on the software version of the System Control is displayed for approx. 2 seconds, and then the
modules are programmed with the settings
stored last in the memories of the System
Control and the MPEG2 decoder.
Error no.
No Module
I2C bus no communication
No response from Memory
No responce from the Backplane
Only Unknown modules
The programming instructions show how to
set different parameters by means of the
keyboard.
During programming the display only shows
the menus to which the module type in
question has access.
If an already applied channel is chosen
during the programming of the output channel
of a module, the display will flash.
....
Wrong software version
or defect module
Module Identification
Module No.
(#1- # 8)
ID
ID
Module no. X defect
Indentification des modules
Indication
Module type
Unknown Module
Module inconnu
or
ou
DSB satellite Module VHF
Module satellite MA VHF
or
ou
DSB satellite Module UHF
Module satellite MA UHF
DSB modulator Module VHF
Voie de modulation MA VHF
DSB modulator Module UHF
Voie de modulation MA UHF
VSB satellite Module
Module satellite MABLR
Display
at power-on
Indication
à la mise
sous tension
Error messages table
Cause
or
ou
VSB modulator Module
Voie de modulation MABLR
DSB -VHF / DVB-sat Module
Module satellite MA VHF DVB
DSB -UHF / DVB-sat Module
Module satellite MA UHF DVB
3
Solution
Place Modul
Contact your dealer
Contact your dealer
Contact your dealer
Check Software version
Check Software version
or replace Module
Replace Modul
PROGRAMMING MENUS
UK
PROGRAMMING MENUS
Software version 2.0 or later.
To unlock the module for programming press the buttons “left” and “right” at the same time.
Locked:
Ready for programming:
.
1. Program (module no.).
Pr01 – Pr08
The System Control checks for correctly mounted module in the selected place.
2.
Input frequency.
0920 – 2150 SAT IF, Frequency (MHz)
3.
LNB control.
L0 – L14 – L18 – L14t – L18t
Off – 14V – 18V – 14V/22kHz – 18V/22KHz
4.1 Symbol rate 2MSD.
4.2 Symbol rate 3LSD.
Sr01 - Sr44
r000 - r999
Example:
SR
SR01 - SR44
r000 - r999
= 22.500
= SR 22
= r500
5. Search mode.
SEAr
Search for services in Transponder stream
(Read light indicates that the transponder is found)
If Search mode finished and result OK:
6.1 Service select mode.
S 01 – S 99 (Service list OSD)
Select service from the multiplex
If Search mode finished and result error:
6.2 Error mode.
Err (Error OSD)
7.
Audio language mode.
SW
twa
re v
on
ersi
Au
7.1 Audio language.
StER - Lb - LA - dual
8
Subtitles.
OFF - 790 - 791 - 792 (text pages with different subtitle languages)
9.
Output channel.
(490641/490643)
S21-S38
System B/G
E05-E12
S11-S38
System D/K
r06-r21
S21-S38
System I
I04-I19
S21-S38
System L
L05-L19
Ch21-Ch60
Ch21-60
Ch21-60
Ch21-60
(490642/490644)
of
=S
To lock the module for programming press the buttons “left” and “right” at the same time.
OUTPUT / SORTIE
ATTENUATOR
DSB / MA MODULE
How to upgrade MPEG2 soft ware
If you want to upgrade your MPEG2 software you will find the
software program and Installation Manual on the Internet.
You can find our web-site on the adress:
www.triax.dk
4
NOTE !!!!
Be sure to place the EPROM in the right
position when you upgrade.
TECHNICAL DATA
Electrical data: TCSD 641/2/3/4
TCSD 651
RF:
Frequency range
Input level
Input impedance
Return loss
(MHz)
(dBm)
(Ohm)
(dB)
920-2150
-65..-25
75
>10
LNB CONTROL:
V/H programmable
LO/HI programmable
(V/mA)
(kHz)
0-14-18 / 400
0 / 22kHz
DEMODULATOR:
Type
Symbol rate
Viterbi decoder:
Reed Solomon decoder
Deinterleaver
Output
(Mbps)
Output frequency range
(MHz)
Output frequency range
(MHz)
Picture carrier stability
(kHz)
Spurious signals ref. picture carrier (dB)
Output level max
(dBµV)
Output level max
(dBµV)
Output impedance
(Ohm)
Return loss (MOD OUT)
(dB)
Differential gain
(%)
Differential phase
(deg.)
Crominance / luminance delay
(ns)
Luminance non-linearity
(%)
Video S/N ratio
(dB)
Sound sub carrier 1
(MHz)
Sound sub carrier 2 (TSCA 623 only)(MHz)
Sound sub carrier stability
(kHz)
Audio distortion, 1kHz
(%)
Audio S/N ratio
(dB)
(V, mA)
CONNECTORS:
Aerial input, SAT
Aerial output, MOD
MPEG2 decoder
Power supply/control
ENVIRONMENT:
Temperature, operation
Temperature, storage
Humidity, operation
Humidity, storage
CONTROL:
Software download
QPSK
1-30 (SCPC/MCPC)
1/2, 2/3, 3/4, 5/6, 7/8.
204,188, t=8.
I=12.
DVB PI TS (LVDS).
Weight
VSB Satellite module
DSB Satellite module
9P RS232 extern
B/G, I, L, D/K
VHF DSB mono
(TCSD 641)
VHF DSB A2 stereo/dual
(TCSD 643)
UHF DSB mono
(TCSD 642)
UHF DSB A2 stereo/dual
(TCSD 644)
175-350 (TCSD 641/3)
470-862 (TCSD 642/4)
< +/-70
> -60
99 (175-350MHz)
96 (470-862MHz)
75
>10
<8
<8
<80
<8
54
5,5 / 6,0 / 6,5
5,74
< +/-5
1
50
5/1100 - 12/10
9P RS232
ENVIRONMENT:
Temperature, operation
Temperature, storage
Humidity, operation
Humidity, storage
-10..+55
-20..+70
20..80
10..90
34P IDC.
EDGE CONNECTOR
(Deg. C)
(Deg. C)
(%)
(%)
DIMENSIONS:
L x W x H)
Weight
(mm)
(kg)
192 x 122 x 40
0,25
Indentification des modules
Module Identification
Module No.
(#1- # 8)
ID
ID
Indication
à la mise
sous tension
Indication
Module type
Unknown Module
Module inconnu
or
ou
DSB satellite Module VHF
Module satellite MA VHF
or
ou
DSB satellite Module UHF
Module satellite MA UHF
Display
at power-on
or
ou
DSB modulator Module VHF
Voie de modulation MA VHF
DSB modulator Module UHF
Voie de modulation MA UHF
VSB satellite Module
Module satellite MABLR
VSB modulator Module
Voie de modulation MABLR
DSB -VHF / DVB-sat Module
Module satellite MA VHF DVB
DSB -UHF / DVB-sat Module
Module satellite MA UHF DVB
5/415 -12/420 - 30/5
18/400 - 23/400 for LNB
F
IEC-M
34P IDC
EDGE CONNECTOR
2X10P
(Deg. C)
(Deg. C)
(%)
(%)
(V/mA)
CONNECTORS:
Transport Stream Input / A-V Output
Power Supply/Control Internal
2X10P
Control Extern
Error no.
Error messages table
Cause
No Module
I2C bus no communication
No response from Memory
No responce from the Backplane
Only Unknown modules
-10..+50
-20..+70
20.....80
10.....90
Mechanical data:
Wrong software version
or defect module
(mm)
192 x 70 x 45
192 x 115 x 45
....
DIMENSIONS:
LxWxH
DSB
VSB
MPEG2/DVB (Main Profile/Main Level)
DVB PI TS (LVDS).
Common Interface (EN 50221)
Pal/Secam
Reinserted in VBI
(Mbps)
<65
(Mbps)
<15
POWER SUPPLY:
MODULATOR:
TV-standard switchable on DIP-switch
System
POWER SUPPLY:
Voltage/current
DECODER:
Type
Input
Conditional Access
Video output norm
Teletext
Demultiplexer data rate
Video data rate
(kg)
0,3
0,2
5
Module no. X defect
Solution
Place Modul
Contact your dealer
Contact your dealer
Contact your dealer
Check Software version
Check Software version
or replace Module
Replace Modul
6
*
M
Search
M
Symbol rate
M
LNB Settings
M
1.Sat MF Input
950-2150 MHz
Fréquence
d’entrée
M
Program (module no.)
Pr.01 , Pr.02 , ...Pr.08
M
M
M
M
M
Programmation
L’accés aux menus de
programmation s’effectue
par action simultanée des
touches “ Droite” & “Gauche”
M
M
M
MS/S
01 - 45
*
M
LNB Off
Vert.
Search
Error
Service
*
OK
KS/S
000 - 999
Searching for service
(approximately 30 sec.)
Ex : 22.500
M
*
Polarity
Vert. = 14 Volt
Horz. = 18 Volt
Low Band
10700 - 11700MHz
See. ex. (A)
Symbol rate
LNB 14 Volt
LNB 18 Volt
Horz.
LNB 14V/22KHz
Vert.
LNB 18V/22KHz
Horz.
High Band
11700 - 12750MHz
See. ex. (B)
Hi Band
(B) 12000MHz (minus) 10600MHz = 1400 MHz
LNB Settings
Lo Band
LNB
1.Sat.MF
(Loc.Osc.)
(A) 11258MHz (minus) 9750 MHz = 1508 MHz
Sat. freq.
Example how to calculate 1. Sat. MF (with a universal LNB)
To “open” the unit for
programming press
left and right buttons
at the same time.
(App. 2 sec.)
Programming
start
Triax Compact Headend :
M
ID
Dot right
Le digit à modifier est selectionné
à l’aide des touches “Droite” & “Gauche”
*Enable moving dot
M
With the “left”/”right” buttons,
one of the digits in the display
can be chosen to be affected.
This digit is indicated by a dot
in the bottom right corner.
Dot left
1
2
3
4
5
6
7
Eng
Eng/Hun
Fre
Eng
Ger
Eng
Fre
BER : E-8
Bit error rate
T
T
T
T
T
R
T
S
S
S
S
Eng =
Single language
Fre / Eng = Multi language
CNN Int.
Travel
Travel
Catoon Network
Cartoon Network
CNN Radio
TCM
Program . No. Name
On screen Service
Mode
“non” = Television
T
= Text tv
S
= Scrambled
T S = Text tv / Scrambled
R
= Radio
Module satellite MABLR DVB
VSB / DVB-sat Module
Language
Module satellite MA VHF DVB
Module satellite MA UHF DVB
DSB -UHF / DVB-sat Module
Voie de modulation MABLR
VSB modulator Module
DSB -VHF / DVB-sat Module
Module satellite MABLR
Voie de modulation MA UHF
DSB modulator Module UHF
VSB satellite Module
Voie de modulation MA VHF
DSB modulator Module VHF
or
ou
Module satellite MA UHF
Module satellite MA VHF
DSB satellite Module UHF
or
ou
Module inconnu
Indication
Indentification des modules
*
(-)
or ou
(+)
Sélection du digit
Move dot left or right
DSB satellite Module VHF
Unknown Module
Module type
Module Identification
= Press Button
Bouton à actionner
Down
M
Up
Déplacement menu
Sélection des paramètres
Move menu or digit
or
ou
ID
+ Program No.
Indication
à la mise
sous tension
M
M
Sub
Menu
The “up” button,
The “right” button,
makes possible
select sub menu
jumping to previus
menu
M
Backwards
Menu
Display
at power-on
Module No.
(#1- # 8)
La valeur affichée est
mémorisée à l’aide
de la touche “M” ,
le menu suivant est
alors accéssible
The displayed value
is selected by means
of the “M” button, and
programming jumps
to next menu.
M
Select
Menu
Operation Digital QPSK - PAL / Secam modules
M
Unlocked
M
M
Stereo
or
Mono
Single language
M
M
M
Language
set at TV
Language
A
Language
B
Affichage de la
version de soft.
( 1 à 2 sec.)
Pour effacer la programmation,
actionner simultanément les
boutons pendant 3 à 5 sec
Reset usine
Code
M
Insérez un module
Contactez votre revendueur
Contactez votre revendueur
Contactez votre revendueur
Vérifiez version de
programme
Vérifiez version de programme
ou remplacez module
Remplacez module
Module défectueux ou Version
de programme non conforme
Module nr. X défectueux
Solution
Replace Modul
Check Software version
or replace Module
Place Modul
Contact your dealer
Contact your dealer
Contact your dealer
Check Software version
Solution
S
S
S
S
Pas de module présent
Pas de communication sur le bus I2C
Pas d’accès mémoire
Pas de dialogue avec les modules
Modules inconnus
Messages d’erreur
Cause
Module no. X defect
Wrong software version
or defect module
T
T
T
T
Select
Fre
Eng/Spa
Ger
Eng/Pol
Error messages table
Cause
7 TCM
8 TCM
9 Bloomberg
10 Bloomberg
No Module
I2C bus no communication
No response from Memory
No responce from the Backplane
Only Unknown modules
Error no.
Dual language only to be used
with stereo modules
Remark:
This menu is only avaiable
on programs with milti language
- Program No.
All segment
Tous les segments sont
on (in 1-2 sec.) apparents (in 1 à 2 sec.)
Software
Revision no.
(in 1-2 sec.)
Press the
buttons
3-5 sec
Reset
Remark:
If one of the button is not affected for more
than 30 minutes in programming mode the unit
automatically goes back in lock mode.
Remarque:
L’appareil revient automatiquement en mode
normal au bout d’une demi heure lorsqu’aucune
touche n’est actionnèe.
Pour sortir du mode
programmation, action
ner simultanément les
boutons
“Gauche” & “Droite”
To “lock” the unit for
programming press
left and right buttons
at the same time.
Light on
(Red LED)
To indentify languages
numbers use teletext
M
Tuner module
Multi language
Lights when
receiving signal
All settings are transfered to systemcontrol
Mèmorisation des paramètres
Programming lock
Sortie mode programmation
M
M
Subtitles language choise:
Mode normal
programming locked
See technical
data sheet
M
Output channel.
Canal de sortie
Return to
Programming start
*
M
Language
M
M
Service
....
....
7
Notes
8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising