RMGA108 - Arrow sheds

RMGA108 - Arrow sheds
Owner's Manual & Assembly Instructions
XK01
Model No.
RMGA108
715900110
Storage Area: 74 Sq. Ft.
6,9 m2
444 Cu. Ft.
12,6 m3
BUILDING DIMENSIONS * Size rounded off to the nearest foot
*Approx.
Size
Base
Size
CAUTION: SOME PARTS HAVE SHARP EDGES. CARE
MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES
TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ
SAFETY INFORMATION PROVIDED IN THIS MANUAL
BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES
WHEN HANDLING METAL PARTS.
Exterior Dimensions
(Roof Edge to Roof Edge)
Width
Depth
Height
Interior Dimensions
(Wall to Wall)
Width
Depth
Height
118 1/4"
10' x 8'
121" x 92 3/4"
123 1/4"
95 1/4"
77 7/8"
3,0 m x 2,3 m
307,3 cm x 235,6 cm
313,1 cm
241,9 cm
197,8 cm
300,4 cm
90"
76 5/8"
228,6 cm 194,6 cm
Door
Opening
Width Height
55 1/2"
65"
141,0 cm 165,1 cm
BEFORE YOU BEGIN....
XA02
Owner's Manual
Before beginning construction, check local building codes regarding footings, location
and other requirements. Study and understand this owner's manual.
Important information and helpful tips will make your construction easier and more
enjoyable.
Instructions are supplied in this manual and contain all
appropriate information for your building model. Review all instructions before you begin,
and during assembly, follow the step sequence carefully for successful results.
Assembly Instructions:
Flooring and Anchoring: Your storage building must be anchored to prevent wind
damage. A base is necessary to construct a square and level building. Anchoring and
base materials are not included with your building. Your assembly instructions provide
information on a few methods commonly used to secure and level a storage building.
Parts and Parts List: Check to be sure that you have all the necessary parts for your
building.
•All part numbers can be found on the parts. All of these numbers (before the -) must agree with the
numbers on the parts list. The parts list is located on page 9.
•If you find that a part is missing, include the model number of your building
and contact the retailer where you purchased your shed.
•Separate contents of the carton by the part number while reviewing parts list. The first few steps
show how to join related parts to make larger sub assemblies which will be used later.
•Familiarize yourself with the hardware and fasteners for easier use during construction. These are
packaged within the carton. Note that extra fasteners have been supplied for your convenience.
2
PLAN AHEAD....
XA03
Watch the Weather: Be sure the day you select to install your building is dry and calm.
Do not attempt to assemble your building on a windy day. Be careful on wet or muddy ground.
Whenever possible, two or more people should work together to assemble
your building. One person can position parts or panels while the other is able to handle the
fasteners and the tools.
Teamwork:
These are some basic tools and materials you will need for the
construction of your building. Decide which method of anchoring and the type of base you
wish to use in order to form a complete list of the materials you will need.
Tools and Materials:
Required
• Eye Goggles
• No. 2 Phillips Screwdriver
(With Hardened Magnetic Tip)
Note: A power screwdriver or variable speed drill with Phillips-tip attachment can speed assembly by
as much as 40%.
Required
• Work Gloves
• Step Ladder
• Utility Knife / Scissors
• Pliers
• Carpenter's Level
• Tape Measure
Optional Time-Savers
• Wrench / Nut Driver
• Electric / Cordless Drill
• Square
• String (for squaring frame)
Base Preparation
• Hammer and Nails
• Spade or Shovel
• Hand Saw / Power Saw
• Lumber and/or Concrete
Selecting and Preparing Your Site: Before assembly, you will want to decide on
a location for your building. The best location is a level area with good drainage.
•Allow enough working space for ease of moving parts into position during assembly. Be sure there
will be enough space at entrance for doors to open fully and enough space around the building to
be able to fasten the panel screws from the outside.
•Before you begin the first steps in assembling your parts, a base should be constructed and
an anchoring system should be ready to use.
3
SAFETY FIRST....
XA04
Safety precautions are important to follow throughout the construction of your building.
•Care must be taken when handling various
pieces of your building since some contain
sharp edges. Please wear work gloves, eye
protection and long sleeves when assembling
or performing any maintenance on your building.
•Practice caution with the tools being used in the
assembly of this building. Be familiar with the
operation of all power tools.
safety edge
sharp edge
sharp edge
safety edge
•Keep children and pets away from worksite to
avoid distractions and any accidents which
may occur.
•Do not attempt to assemble the building if parts
are missing because any building left partially
assembled may be seriously damaged by light
winds.
•Never concentrate your total weight on the
roof of the building. When using a step ladder
make sure that it is fully open and on even
ground before climbing on it.
•Do not attempt to assemble the building on a
windy day, because the large panels acting as a
"sail", can be whipped about by the wind making
construction difficult and unsafe.
4
CARE & MAINTENANCE....
XA05
For long lasting finish, periodically clean and wax the exterior surface. Touchup scratches as soon as you notice them on your unit. Immediately clean the area with
a wire brush; wash it and apply touch-up paint per manufacturer's recommendation.
Finish:
Roof: Keep roof clear of leaves and snow with long handled, soft-bristled broom. Heavy
amounts of snow on roof can damage building making it unsafe to enter.
Doors: Always keep the door tracks clear of dirt and other debris that prevent them from
sliding easily. Lubricate door track annually with furniture polish or silicone spray. Keep
doors closed and locked to prevent wind damage.
Fasteners: Use all washers supplied to protect against weather infiltration and to protect
the metal from being scratched by screws. Regularly check your building for loose
screws, bolts, nuts, etc. and retighten them as necessary.
A plastic sheet (vapor barrier) placed under the entire floor area with good
ventilation will reduce condensation.
Moisture:
Other Tips....
• Wash off inked part numbers on coated panels with soap and water.
• Silicone caulking may be used for watertight seals throughout the building.
Do not store swimming pool chemicals in your building. Combustibles and
corrosives must be stored in air tight approved containers.
Keep this Owner's Manual and Assembly Instructions for future reference.
5
Base
XK06
The Base For Your Building
OPTION 1: Wood Platform
If you decide to build your own base, be sure to select the appropriate materials.
These are the recommended materials for your base:
● 2 x 4's (38 mm x 89 mm) Pressure Treated Lumber ● 5/8" (15,5 mm) 4 x 8 (1220 mm x 2440 mm) Plywood-exterior grade
● 10 & 4 penny Galvanized Nails ● Concrete Blocks (optional)
40,
The platform should be level and flat (free of bumps, ridges etc.)
to provide good support for the building. The necessary materials
may be obtained from your local lumber yard.
To construct the base follow instructions and diagram.
Construct frame (using 10 penny galvanized nails)
Measure 16"/24" (40,6 cm/61,0 cm) sections to construct
inside frame (see diagram)
Secure plywood to frame (using 4 penny galvanized nails)
FRONT
(DOOR)
Allow 6 - 7 hours for construction.
16
6 c "/24"
m/6
1,0
c
1
307 21"
,3 c
m
m
"
3/4
92 ,6 cm
5
23
Note: Platform/Slab will extend 9/16" (1,4 cm) beyond
floor frame on all four sides. Seal this 9/16" (1,4 cm) of
wood with a roofing cement (not included), or bevel
this 9/16" (1,4 cm) of concrete when pouring,
for good water drainage.
OPTION 2: Concrete Slab
The slab should be at least 4" (10,2 cm) thick. It must be level and flat to provide good support for the frame.
The following are the recommended materials for your base.
● 1 x 4's (19 mm x 89 mm) (will be removed once the concrete cures)
● Concrete ● Sheet of 6 mil plastic
● We recommend for a proper strength concrete to use a mix of:
1 part cement ● 3 parts pea sized gravel ● 2 1/2 parts clean sand
Prepare the Site/Construct a Base
1. Dig a square, 6" (15,2 cm) deep into the ground (remove grass).
2. Fill up to 4" (10,2 cm) in the square with gravel and tamp firm.
3. Cover gravel with a sheet of 6 mil plastic.
4. Construct a wood frame using four planks of 1x4 (19 mm x 89 mm)
lumber.
5. Pour in concrete to fill in the hole and the frame giving a
total of 4" (10,2 cm) thick concrete. Be sure surface is level.
1
307 21"
,3 c
FRONT
m
(DOOR)
Note: Finished Slab dimensions, with lumber removed.
Allow 3 - 5 hours for construction and a week for concrete curing time.
6
"
3/4 m
2
9 ,6 c
5
23
Anchoring
XA07
Anchoring Down The Building
It is important that the entire floor frame be anchored after the building is erected.
Below are recommended ways of anchoring.
Anchoring into Wood/Post:
Use 1/4" (6 mm) Wood Screws. There are 1/4" (6 mm)
dia. holes provided in the frames for proper anchoring.
1.
2.
Anchoring into Concrete:
1. For poured concrete slab or footing or patio blocks:
Use 1/4" x 2" (6 mm x 51 mm) Lag Screws.
2. For Anchor Post of Concrete poured after building is
erected: Use 1/4" x 6" (6 mm x 152 mm) Lag Screws.
2.
1.
7
Hardware
XK08
Remove from bag of screws
and save for the last step
65103
#8-32 Hex Nut (161)
65900A
#10Bx1/2" (13 mm)
Black Screw (8)
(Packed with Screws)
65923
#8-32x3/8" (10 mm)
Bolt (161)
65004
#8Ax5/16" (8 mm)
Screw (326)
66045
Handle (2)
66646
Washer (369)
(10 sheets of 40)
65109
#8-32 Acorn Nut (4)
(Packed with Screws)
67468
Peak Cap (2)
(Arrow Logo)
66769
Door Slide (4)
66382
Lower Door Guide (4)
66183
Roof Trim Cap
(2 right & 2 left)
6228
Track Support (2)
5971
Roof Beam Bracket (4)
67293
Weather Stripping (1)
8
Parts List
XK09
Parts in Carton One
Assembly
Key No.
1
2
3
4
5
6
7
8
9
10
11
12
Assembly
Key No.
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Part
Number
Part
Description
8200
9374
6000
6001
6627
6529
10477
7483
8468
8469
8471
69835
Wall Panel (Side)
Front Wall Panel
Right Gable
Left Gable
Wall Panel
Roof Panel
Right and Left Doors
Roof Panel
Right Roof Panel
Left Roof Panel
Corner Panel
Edge Trim (Green)
Parts in Carton Two
Part
Part
Number Description
3719
9365
5986
10497
6300
6403
9366
6635
9370
9917
8485
8840
10470
8836
9922
8839
8486
8934
9367
8936
8937
Door Handle Brace
Front Wall Channel
Rear Wall Angle
Horizontal Door Brace
Vertical Door Brace
Door Track Splice
Door Track
Gable Brace
Door Jamb
Rear Wall Channel
Left Side Roof Trim
Ridge Cap
Roof Beam
Right Side Roof Trim
Side Wall Channel
Side Wall Angle
Ridge Cap
Ramp
Front Floor Frame
Rear Floor Frame
Side Floor Frame
9
Quantity
in Carton
Check
List
4
2
2
2
6
2
2
4
2
2
4
4
Quantity
in Carton
2
2
2
4
2
1
2
2
2
2
2
1
8
2
4
4
1
1
2
2
4
Check
List
Assembly by Key No.
XK10
10
23
29
25
28
8
3
11
9
1
28
12
8
6
26
24
25
5
1
11 19
4
27
2
25
25 27
21
3
4
25
6
12
26
15
5
28
23
22
11
5
5
12
1
32
19
33
8
8
5
16 18
28
27
5
17
7 13
13
33
31
22
10
16
14
9
25 25 20
15
25
20
17
12
7
21
1
2
11
16
33
14
30
16
33
31
10
32
27
● 8934 Ramp (1)
● 9367 Front Floor Frame (2)
● 8936 Rear Floor Frame (2)
● 8937 Side Floor Frame (4)
● Parts Needed For ●
Step 1
Floor Frame Assemblies
XK11
(8)
(13)
The front floor frame is made up of
three pieces. The side floor frames
and the rear floor frame are made up
of two pieces. The holes in these
pieces will align when the pieces are
positioned with correct amount of
overlap. The illustrations below show
the proper overall length for the sides,
rear and front. Proceed as follows:
1
9367
8934
9367
8936
8937
STEP
Front Floor
Frame Assembly
119 3/8" 303,2 cm
8934
1
9367
Place the front floor frames as
shown. Center the ramp, with drain
holes facing outside, on top of the two
front floor frames. Join the frames by
inserting eight screws.
9367
DRAIN HOLES FACE
OUTSIDE
8937
Side Floor Frame 91 1/8" 231,5 cm
2 Overlap the side floor frames and
the rear floor frames as shown. The
holes in these pieces will align when
the pieces are positioned with correct amount of overlap. See the illustrations below for the proper overall
length of the side and rear floor frames.
Join the frames by inserting four/five
bolts into each frame set as shown.
8937
STEP
2
8936
Rear Floor Frame 119 3/8"
303,2 cm
8936
3
Double check the length of each
and set these pieces aside for later
use.
91 1/8" 231,5 cm
91 1/8" 231,5 cm
119 3/8" 303,2 cm
STEP
Front & Rear
3
119 3/8" 303,2 cm
11
Step 2
● 5986 Rear Wall Angle (2)
● 9917 Rear Wall Channel (2)
● 9922 Side Wall Channel (4)
● 8839 Side Wall Angle (4)
● Parts Needed For ●
Frame Assemblies
XK12
Rear Wall Channel
118 1/8" 300,0 cm
9917
9917
(6)
The main frame pieces reinforce the
walls. These pieces will later be installed in the center and at the top
edge of the side walls and the rear
wall. Proceed as follows:
Side Wall Channels
89 7/8"
228,3 cm
9922
9922
1
Overlap the rear wall channel
pieces as shown in the figure and
fasten the two pieces together with
one bolt in the center hole (three
holes will align).
STEP
STEP
1
2
Rear Wall Angle
118 1/8" 300,0 cm
5986
5986
2 Make two side wall channels by
overlapping the side wall channel
pieces as shown. Fasten each set
together with one bolt in the center
hole of each set.
Side Wall Angles
89 7/8" 228,3 cm
8839
8839
3
Overlap the rear wall angle
pieces as shown in the figure and
fasten them together with one bolt in
the center hole.
STEP
STEP
3
4
Rear Wall Channel
118 1/8" 300,0 cm
4
Make two side wall angles by
overlapping the side wall angle pieces as shown. Fasten each set together with one bolt in the center hole.
Side Wall Channels
89 7/8" 228,3 cm
5
Double check the length of each
and set these pieces aside for later
use.
Rear Wall Angle
118 1/8" 300,0 cm
STEP
5
12
Side Wall Angles
89 7/8" 228,3 cm
● Parts Needed For ●
Step 3
Roof Beam Assemblies
● 10470 Roof Beam (8)
XK13
(30)
10470
The roof beams join the two gables
and support the roof panels. The main
roof beam is made up of four pieces
overlapped back to back at the center. The left and right roof beam assemblies are made up of two pieces.
Hint: These pieces are force-fitted,
so you may have to press hard to join
them together.
10470
STEP
1
Roof Beam 91 7/8"
233,4 cm
1
Place the end of one roof beam
inside a second roof beam so that the
six holes in each piece align. Make
four sets of roof beams by repeating
this procedure. Do not insert bolts
yet.
2 Take two of the pressed-together
ASSEMBLED
roof beams and join them as shown
to form the main roof beam assembly.
Hold the assembly together and fasten with 14 bolts. Build only one
Doubled Beam Assembly.
STEP
END
VIEW
2
10470
Build one Doubled Main Roof
Beam Assembly for Peak in Roof
10470
3
Fasten the other two pressedtogether roof beams with eight bolts
to make the left and right roof beam
assemblies.
STEP
3
10470
4
Double check the length of each
and set these pieces aside for later
use.
10470
Build two Single Beam Assemblies
91 7/8"
233,4 cm
13
91 7/8"
233,4 cm
● Parts Needed For ●
Step 4
Door Track Assembly
● 6403 Door Track Splice (1)
● 9366 Door Track (2)
XD14
NOTE:
Door Track Splice (painted part)
(4)
The door track assembly supports
the sliding doors and reinforces the
front wall. It is made up of three pieces.
6403
1
Using the door track splice,
(painted), join the door track
(galvanized) pieces end-to-end as
shown.
2 Insert four screws from the underside only.
66769
9366
9366
STEP
STEP
1
2
Short Leg
on Bottom
9366
Hint: The holes in the top side of the
door track assembly are for fastening
the gable to the top of the front wall in
a later step.
6403
9366
118 1/8"
300,0 cm
3
Position door slides onto the
legs, from the end of door track
assembly, as shown in the end view.
4 Set this piece aside for later use.
END VIEW
Long Leg
on Top
STEP
STEP
3
4
118 1/8"
300,0 cm
66769
118 1/8"
300,0 cm
14
● Front Floor Assembly (1)
● Side Floor Assembly (2)
● Rear Floor Assembly (1)
● Parts Needed For ●
Step 5
Floor Frame
XK15
(8)
(2)
RIGHT
REAR
8937
1 Assemble the four corners of the
floor frame using two screws at each
corner as shown. At the front corners
fasten bolts through from
the bottom with nuts on top.
STEP
8936
1
FR
ON
T
RIGHT
FRONT
8937
2
Measure the floor frame diagonally. When the diagonal measurements are equal, the floor frame is
square.
9367
NOTE
If using a wood platform or
concrete slab do not fasten the
floor frames to your base at this
time. You will anchor the
building after it is erected.
When Diagonal Measurements
are Equal the Floor Frame
is Square.
STEP
2
Level
The floor frame must be square
and level or holes will not align.
15
● Parts Needed For ●
Step 6
● 6627 Wall Panel (2)
● 9374 Front Wall Panel (2)
● 8471 Corner Panel (4)
Corners
XK16
(26)
8471
(4)
Narrow
Side
Wide Side
NOTE
The remainder of the building assembly
requires many hours and more than one
person. Do not continue beyond this point
if you do not have enough time to complete the assembly today. A partially
assembled building can be severely
damaged by light winds.
REAR
8471
SIDE
Each screw and bolt in the wall requires a washer.
STEP
SIDE
TOP VIEW
8471
1
8471
FRONT
1
CORRECT
INCORRECT
6627
6627
Position a corner panel at the
corner of the floor frame as shown.
The widest part of each corner panel
must be placed along the side of the
building for all four corners. Fasten
the corner panel to the floor frame
with one screw.
STEP
3
STEP
2
Support the corner panel with a step
ladder until a wall panel is attached.
front corner panels, as shown. A small
gap will exist between front wall panel
and ramp.
3 Attach the wall panels to the rear
corner panels, as shown.
STEP
6627
8471
4
8471
6627
Crimped Rib
Underneath
8471
9374
Washer
NOTE
Be careful to install the correct
panel in each position as shown
9374
4 Double-check the part numbers of
the wall panels, before proceeding.
The floor frame must be square
and level or holes will not align.
9374
9374
2 Attach the front wall panels to the
Panels rest on
frame as shown
16
8471
● Parts Needed For ●
Step 7
Frames
XK17
● Door Track Assembly (1)
● Rear Wall Angle Assembly (1)
● Side Wall Angle Assemblies (2)
● Rear Wall Channel Assembly (1)
● Side Wall Channel Assemblies (2)
5986
(30)
(2)
The main frame pieces give rigidity to
the side walls and provide a surface
for attaching the gables which support the roof.
Wall Angles
Must Face
Inside
Building
9917
1
Fasten the rear wall angle assembly across the inside top of the
rear wall using screws.
2 Fasten the rear wall channel assembly across the middle of the rear
wall using screws.
STEP
STEP
1
2
FRONT
8839
3 Fasten the side wall angles across
the inside top of the side panels using screws. Side wall angles must
overlap rear wall angle in corners.
9922
4
Fasten the side wall channel
assemblies across the middle of the
side panels using screws. Fasten
overlaps in rear corners with screws.
5 Fasten the door track assembly
(holes on top) across the top of the
front wall panels using screws. See
the figure.
STEP
STEP
3
4
FRONT
Long Leg
on Top
9366
Opening
Facing in
Door Track
Assembly
Short Leg
on Bottom
NOTE
The wall channels behind the
front wall panels will be installed
in a later step.
STEP
5
FRON
T
17
● Parts Needed For ●
Step 8
● 8200 Wall Panel (4)
● 6627 Wall Panel (4)
Wall Panels
XK18
STEP
6627 6627
1
(112)
(17)
8200
The wall panels come in two widths.
6627
Each wall panel has a crimped rib on 8200
one side. The crimped rib should go
under the rib of the panel that follows
it.
STEP
2
8200
6627
1 Locate all of the wall panels and
Panels rest on
frame as shown
set each one alongside the building.
2 Be sure that you have the correct
8200
Crimped Rib
Underneath
panels in each position. Do this by
overlapping the panels and determining if the holes line up with the
holes in the frame.
Detail Showing
Center of Panel Screwed
to Wall Channel
3 Fasten the wall panels at the top
and bottom with screws.
4 Fasten the center of each panel to
the wall channel with screws. Fasten
overlapping ribs as before.
STEP
3
STEP
5
4
When you have attached all wall
panels in the correct positions, the
building will look like this.
Use bolts and
nuts thru wall
angle overlaps
at the top of
panel at sides
and rear.
STEP
5
18
Bolt and nut
does not go thru
wall channel
at overlap
● Parts Needed For ●
Step 9
● 9370 Door Jamb (2)
● 9365 Front Wall Channel (2)
Front Channel/Door Jamb
XD19
9365
(4)
STEP
T
1
ON
The door jambs reinforce the door
opening and provide an attractive
trim. Follow these steps for both
door jambs.
FR
(18)
INSIDE OF
BUILDING
1 Fasten the front wall channels
in their positions between the end of
the side wall channel and the corner panel using screws. Do not put
a screw in the hole at the end behind the door opening at this time.
STEP
(2) bolts
2
Door Track
Acorn Nut
9370
Bolt
2 Fasten a door jamb to the front
panel with two bolts, nuts and acorn
nuts, as shown.
Hex Nut
Front Wall Channel
Acorn Nut
Screw
STEP
Screw
9370
3
T
ON
FR
4 Fasten the top of the door jamb to
Front Wall Channel
Cross-Section
Top View
TOP VIEW
3
Fasten the center of the door
jamb to the front wall panel and the
front wall channel with two screws.
TOP VIEW
the door track with two screws. Do
the same for the bottom into frame.
TOP VIEW
Repeat steps 2 through 4 for the
opposite door jamb.
Door Track
Screw
STEP
4
19
Screw
Step 10
● Parts Needed For ●
● 6000 Right Gable (2)
● 6001 Left Gable (2)
● 5971 Roof Beam Bracket (4)
Gable Assemblies
XD20
(8)
Edge Trim
(Plastic Piece)
The gables go on top of the front and
rear walls to support the roof beams.
STEP
1
NOTE
The gables are packed nested
together and might be mistaken
as one piece. Carefully separate
them before continuing.
1 Apply edge trim to the top edge of
the right gables and left gables.
2
Attach the four roof beam
brackets to the gables using two
bolts, washers and nuts.
6001
NOTE
Mounting leg of bracket must
face toward center of gable
and holes closest together
must be on top
FR
6000
ON
T
Washer
CAUTION:
To avoid mishap on the sharp
edge the edge trim must remain
in place on the top edge of the
gable until right and left roof
panels are in place.
5971
Roof Beam
Brackets
6001
STEP
2
20
● Left Gable Assemblies (2)
● Right Gable Assemblies (2)
● 6635 Gable Brace (2)
● Parts Needed For ●
Step 11
Gables/Braces
XD21
(20)
(5)
1
Lift and fasten a right and left
gable, under angle at corner, to the
door track and rear wall angle with
screws.
Hint: On the rear gable, use a bolt
and nut at the overlapping rear wall
angle. On the front gable, leave out 2
screws closest to center gable leg.
2
Join the left and right gables
together with a gable brace using a
bolt and nut in the bottom hole only.
3
Repeat Steps 1 & 2 for the door
track on the front of building, except
for the track supports, fasten as
shown.
STEP
1
Gable
6635 Gable Brace
STEP
2
Track Supports 6228
STEP
3
21
● Parts Needed For ●
Step 12
● Main Roof Beam (1)
● Single Roof Beam (2)
Roof Beams
XD22
(12)
STEP
1 Spread the two halves of the main
3
roof beam and fasten the roof beam
to the gable brace of the front gable.
Single Roof Beam Assembly
2 Fasten the other end of the main
roof beam to the gable brace of the
rear gable.
STEP
2
3
Fasten the single roof beams,
small holes on top, as shown using
bolts and nuts.
Spread Two Halves
Of Roof Beams
STEP
1
Main Roof Beam Assembly
22
● Parts Needed For ●
Step 13
● 8468 Right Roof Panel (1)
Right Roof Panel
XK23
STEP
1
(2)
(5)
Installing the roof panels is best done
with a step ladder. Begin installing
roof panels at the back right corner of
the building. Each screw and bolt in
the roof requires a washer.
NOTE
Measure the building diagonally
again and make adjustments to
make sure the building is square.
This will make the roof panels fit
better, and holes will align.
NOTE
If a Roof Beef-Up Kit was
purchased, assemble prior to
attaching the roof panels.
1
Locate the roof panels by their
numbers. Note the sequence and
position they are to be installed.
8469
2
1
8468
7483
6
5
7483
6529
8
7
6529
7483
10
9
7483
8468
4
3
8469
FRONT
STEP
STEP
STEP
2
3
4
Hint: Follow the fastener sequence
shown for proper alignment.
7
3
back right corner and fasten to the top
roof beam using a screw.
Remove edge trim from the left
gable under the roof panel.
8468 Right Roof Panel
2
2 Position a right roof panel at the
3
1
FRON
T
4
Gable
Continue fastening the right roof
panel to the gable and lower roof
beam using screws, bolts and nuts
as shown. Do not fasten the lower
end of the panels to the side wall
angles at this time.
Nut
Washer
23
Bolt
4
5
6
● 8468 Right Roof Panel (1)
● 8469 Left Roof Panel (2)
● 7483 Roof Panel (2)
● 6529 Roof Panel (2)
● Parts Needed For ●
Step 14
Roof Assembly
XK24
(38)
(19)
1 Install a left roof panel at the left
STEP
STEP
8469 Left Roof Panel
7483 Roof Panel
2
1
Weather Stripping
7483 Roof Panel
Tape Roll
6529 Roof Panel
6529 Roof Panel
rear and right front corner of the roof.
Install a right roof panel at the left 8468 Right
Roof Panel
front corner of the roof.
2 Cut 4 short 2" (5,1 cm) strips off the
roll of weather stripping tape, and
put them aside. Cover the joint at the
peak with weather stripping tape.
Unroll the tape and press it down
over the opening at the ridge as you
install each roof panel. Do not cut the
tape at this time.
3 Install 2 narrow and 2 wide roof
panels in the sequence and positions shown on previous page. Do
not fasten the lower end of the panels
to the side wall angles at this time.
Continue weather stripping the ridge
opening.
FRON
STEP
T
3
Screws To
Roof Beam
NOTE
Narrow roof panel crimped rib is
overlapped by wide rib of
adjacent panel where possible.
Fasten At
Overlap with
Bolt
Fasten At
Overlap with
Bolt
Screws To
Roof Beam
NOTE
If roof beam holes do not line up
with the roof panel holes, shift the
building from left to right.
If this does not help, your building
may not be level. Shim the
corners until holes line up.
Do not fasten
at this time
24
● Parts Needed For ●
Step 15
Ridge Caps & Panels
● 8840 Ridge Cap (1)
● 7483 Roof Panel (2)
● 8486 Ridge Cap (1)
XK25
(40)
(16)
1
Install the first ridge cap on the
completed roof section using bolts
and nuts. Fasten roof panel overlaps
not used for ridge cap. Cover the
head of bolt with the 2" (5,1 cm) piece
of weather stripping tape. Do not
fasten the ends of the ridge cap at this
time.
8840
STEP
Strips
1
2 Install the second ridge cap overlapping the first ridge cap while installing the remaining narrow roof
panels. Continue weather stripping
the ridge.
3 Fasten the lower end of the panels
to the side wall angles using screws
and washers. Use bolts and nuts
through wall angle overlaps at the
bottom of the panel.
8486
Cut Weather
Stripping and
Fold Under
STEP
2
7483
7483
STEP
3
25
● Parts Needed For ●
Step 16
● 8485 Left Side Roof Trim (2)
● 8836 Right Side Roof Trim (2)
Roof Trim
XK26
(8)
(4)
(4)
1 Attach the right and left side roof
trim to the lower end of the roof panels on each side of the building using
screws at each panel overlap.
NOTE
A single screw fastens both trim
pieces at the overlap.
2
Using your thumb and index finger, overbend the bottom flange of
the side roof trim at the corner inward
enough so the right and left roof trim
caps fit onto right and left corners.
STEP
1
8485
Roof Trim
3
Fasten the roof trim caps to the
side trim using a screw.
8836
4
8836
Fasten the roof panel ribs, peak
caps and ridge caps together using
bolts and nuts.
8485
Peak Cap
STEP
4
Roof Trim Cap
26
STEP
STEP
2
3
Tuck Flange
Inward to Fit
Inside of
Roof Trim Cap
Step 17
● 3719 Door Handle Brace (2)
● 10477 Right and Left Doors (2)
● 10497 Horizontal Door Brace (4)
● 6300 Vertical Door Brace (2)
● Parts Needed For ●
Door Assembly
XD27
(6)
(12)
The steps on this page tell how to
assemble the right door. You will
perform exactly the same procedures
for the left door. Each bolt and screw
in the door requires a washer. Proceed as follows:
1 Attach the door handle brace and
(4)
66045
10497 6300
3719
66045
3719
6300
10497
66382
66382
handle to the door with 1 bolt as
shown. Don't tighten the bolt yet.
66382
10477
Right Door
10477
Left Door
2 Swing the door handle brace up to
66382
the hole on the center of the door and
insert a screw.
10497
3
Hold the vertical door brace
against the center of the inside surface of the door and turn the screw to
hold the vertical door brace and door
handle brace in place. Fasten to
door above and below center
connection using 2 screws.
STEP
6300
4
the top edge and bottom edge and
fasten with 1 bolt in the center.
66045
STEP
STEP
4
STEP
2
Insert a second bolt in the door
handle and tighten both bolts.
5 Put a horizontal door brace onto
1
3719
5
STEP
3
6 Attach the lower door guides and
10497
END VIEW
SHOWING:
bolts as shown.
Horizontal
Door Brace
7
Repeat steps 1 through 6 for the
left door.
DOOR
WASHER
66382
STEP
6
27
GUIDE
Step 18
● Parts Needed For ●
● Right Door Assembly (1)
● Left Door Assembly (1)
Door Installation & Adjustment
XD28
Gable
Horizontal Door Brace
Door Track
(8)
Door Slide
1
Door
From inside the building, put the
bottom of the right door assembly (on
your left when you are inside the
building) behind door jamb into the
front frame track.
STEP
STEP
1
2
2 Position the top of the door so that
the holes in the door line up with the
holes in the door slides.
Front Floor Frame Assembly
3 Fasten the door to the door slides
using two #10Bx1/2" (13 mm) screws
per door slide.
Door Slide
NOTE
The holes in the door slides allow
you to adjust the doors. Place the
door in the middle holes.
Adjustment Holes
4
Repeat steps 1 through 3 for the
left door.
#10Bx1/2" (13 mm)
Screw
STEP
3
Adjustment Holes Allow
Doors to Meet Evenly
Along Their Length
Right Door
Left Door
STEP
4
Keep this Owner's Manual and Assembly Instructions for future reference.
28
RMGA108
XK31
Anchoring
Anchor your building at this time.
SOME FACTS ABOUT RUST
Rusting is a natural oxidizing process that occurs
when bare metal is exposed to moisture. Problem
areas include screw holes, unfinished edges, or
where scrapes and nicks occur in the protective
coating through normal assembly, handling and
use. Identifying these natural rusting problem areas
and taking some simple rust protection precautions
can help to stop rust from developing, or stop it
quickly as soon as it appears.
1. Avoid nicking or scraping the coating surface,
inside and out.
2. Use all the washers supplied. In addition to protecting against weather infiltration, the washers protect the metal from being scraped by the screws.
3. Keep roof, base perimeter and door tracks free of
debris and leaves which may accumulate and retain
moisture. These can do double damage since they
give off acid as they decay.
4. Touch up scrapes or nicks and any area of visible
rust as soon as possible. Make sure the surface is
free of moisture, oils, dirt or grime and then apply an
even film of high quality touch-up paint.
715900110
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising