Haiku Bamboo S3150-S1 | Haiku K3150-S1, Bamboo S3150-S1 Ceiling Fan Installation Guide

www.haikufan.com

©2012 Delta T Corporation

Installation Guide

S1

Installation Guide:

090512–May 2012

Rev. C

Model Number: K3150-S1

S3150-S1

May be protected by one or more of the following patents:

Australian Registered Design No. 325331, 328015; U .S. Pat. Nos. D612476 and D614757; Malaysian Registered Design

No. MY09-00255-0101, MY09-00973-0101; and Singapore Registered Design No. D2008/951/E and D2009/235/G.

Haiku and the Haiku logo are trademarks of Delta T Corporation, registered in the United States and/ or other countries.

Thank you for buying the world’s most innovative fan. Please take a few moments to register your fan with us online at www.haikufan.com/warrantyregistration.

This product is sold by a plant whose

Management System is certified as being in conformity with ISO 9001:2008.

4004784

4004783

Conforms to ANSI/UL STD 507

Certified to CAN/CSA C22.2 No. 113

This device complies with Part 15 of the

FCC Rules. This device complies with

Canada ICES-003, Class B.

INTRODUCTION

1

About Haiku

Technical specifications

2

Parts & hardware

Fan diagram

PREPARATION

3

Unpacking your fan

Determining fan location

Tools needed

Contents

OPERATION

9

Powering the fan

Replacing remote battery

Changing fan speed

Sleep mode

Timer mode

Whoosh mode

10

Fan mode indicators

TROUBLESHOOTING

11

General troubleshooting

INSTALLATION

4

Installing the airfoils

5

Installing the lower cover

Installing rubber bumpers

6

Attaching the mounting plate

Securing the safety cable

7

Wiring the fan

Hanging the fan

Securing the wiring cover

8

Wire color chart

Wiring diagram

MAINTENANCE

12

Annual maintenance

WARRANTY

13

Warranty policy

HAIKU by Big Ass Fans

i

IMPORTANT SAFETY INSTRUCTIONS

Read and save these instructions prior to installing and operating your Haiku. Retain this installation guide for maintenance and troubleshooting information. If you have further questions, contact Haiku Customer Service at www.haikufan.com/service.

WARNING: To reduce the risk of fire, electric shock, and serious bodily injury to persons, observe the following:

• Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards.

• When cutting or drilling into ceiling, do not damage electrical wiring and other hidden utilities.

• Use this fan only in the manner intended by the manufacturer.

CAUTION: The installation of this fan must be in accordance with the requirements specified in this installation manual and with any additional requirements set forth by the national electrical code (NEC),

ANSI/NFPA 70-2008, and all local codes. Code compliance is ultimately YOUR responsibility!

WARNING: If installing the fan in Australia, a licensed electrician must perform the electrical installation.

CAUTION: Exercise caution and common sense when powering the fan. Do not connect the fan to a damaged power source. Do not attempt to resolve electrical malfunctions or failures on your own.

WARNING: The fan must be used with the supplied remote control. Other parts cannot be substituted.

CAUTION: When service or replacement of a component in the fan requires the removal or disconnection of a safety device, the safety device must be reinstalled or remounted as previously installed.

WARNING: Power must be disconnected before installation and servicing, cleaning, and other usermaintenance. Failure to disconnect power creates risk of fire, electric shock, and serious bodily injury.

CAUTION: The product warranty will not cover equipment damage or failure that is caused by improper installation or operation.

CAUTION: The fan must be mounted a minimum of 7 ft (2.1 m) from the floor and 3 ft (1 m) from the nearest wall. The ceiling should be stable with no shaking, high vibrations or heavy impacts.

WARNING: Do not install the fan in an environment that is excessively dusty, conductive, corrosive, or gas-filled, is exposed to open flames (e.g., gas-burning stoves), is near strong chemicals or solvents, or where there is excessive heat, shock, or vibration.

WARNING: Do not bend the airfoils when installing or servicing the fan. Do not insert foreign objects in between the rotating fan airfoils.

CAUTION: This fan is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the fan by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the fan.

WARNING: Before installing or servicing the fan, ensure power is disconnected.

CAUTION: Haiku (K3150-S1) is rated for use in damp environments and can be operated indoors or outdoors. Haiku Bamboo (S3150-S1) is not rated for damp environments and must be operated indoors only.

CAUTION: The fan will begin rotating when power is applied.

ii

©2012 DELTA T CORP. ALL RIGHTS RESERVED.

INTRODUCTION

Thank you for your Haiku purchase and congratulations on your selection of an elegant, efficient, and cost-effective way to stay cool! We are proud to assure you that the fan you have chosen is backed by extensive research, thorough testing, and quality manufacturing.

If you have any questions or comments, please contact Customer Service by visiting our Web site at www.haikufan.com/service.

About Haiku

Haiku products are inspired by the seamless integration of natural forms and materials with the latest technologies. Haiku fans consume up to 80% less energy than traditional ceiling fans and maximize the sustainable use of global resources so you can now help save the planet in STYLE.

Backed by the engineering resources of Big Ass Fans, the fan of choice for smaller spaces that need extraordinary air movement is crystal clear—it’s Haiku.

Technical specifications

Before assembling and installing your fan, review the technical specifications in the table below. A fan diagram and parts list can be found on the following page.

Model

Model number

Fan diameter

Number of airfoils

Weight

Number of fan speeds

Operating voltage

Operating frequency

Full load amps

Wattage

Ambient operational temperature range

Operational humidity range

Status indication

Haiku / Haiku Bamboo

K3150-S1 / S3150-S1

60 in. (1.5 m)

3

13.2 lb (6 kg)

6

100–240VAC 1Φ

50–60 Hz

0.363A

Max: 25 Watts

Min: 4 Watts

32°–104° F (0–40° C)

20–90% non-condensing

LED display

HAIKU by Big Ass Fans

1

INTRODUCTION (CONT.)

Parts and hardware

If you are missing any parts or hardware required for the installation or operation of your Haiku, contact

Haiku Technical Service. Note: Drawings below are not to scale.

1 2

3

4

Mounting plate

5

(2) Rubber bumper

(2) Mounting bracket

6

(3) Airfoil Motor hub Lower cover

*The remote control holder and hardware are not shown.

8

7

(4) 6 mm Flat washer

(4) 6 mm

Nylock nut

Remote control*

Safety cable shackle*

(2) Extension tube screw cap

9

(6) Airfoil grommet

(Haiku Bamboo only)

(6) 5 mm

Lock washer

(6) M5 Airfoil screw

1

6

(4) Wire Nut

*Safety cable is not shown in diagram.

**Wiring is hardware not shown in diagram.

2

3

7

5

8

4

2

9

6

©2012 DELTA T CORP. ALL RIGHTS RESERVED.

Preparation

Before assembling and operating your fan, review the following tips and guidelines to ensure a safe and easy installation, particularly the safety guidelines on page ii. If you have questions about any aspect of the installation process, consult a structural engineer or electrical contractor or contact

Haiku Technical Service.

Unpacking the fan

As you remove the fan from its packaging, make sure you are not missing any components required for assembly and operation. Refer to the fan diagram and the Parts and Hardware section for a list of components. Do not discard the packaging! It will be used during the installation process. If you are missing a part required for installation, contact Haiku Technical Service.

!

If you ordered multiple fans, be sure to keep the components of each fan together! Certain fan components are not interchangeable.

Determining fan location

Consider the following guidelines as you decide where to install your Haiku:

• Do not mount the fan in an environment that is excessively dusty, conductive, corrosive, or gasfilled, near strong chemicals or solvents, or where there is excessive heat, shock, or vibration.

• Do not install the fan near open flames such as those from a gas stove.

• The ceiling should be stable with no high vibrations, shaking, or heavy impacts.

• Install the fan so that the airfoils are at least 2.4 m above the floor.

• Make sure the space around the fan has a clearance of at least 1 m from obstructions such as cabinets, doors, lighting fixtures, etc.

• Make sure the space between the fan and ceiling is clear of any obstructions.

• Install the fan on a switched circuit so that you can turn off the fan using a wall switch in addition to using the remote control.

No

Obstructions

1 m Min. to

Obstruction

2.4 m Min. to Floor

Tools needed

You will need the following tools to install the fan:

• Ladder

• Hex key (provided)

• Wire stripper

• Adjustable wrench

HAIKU by Big Ass Fans

• #1 Phillips screwdriver

3

Installation

Review the safety guidelines. If you are not completely comfortable or have questions about any aspect of the installation process, consult a structural engineer or electrical contractor or contact

Haiku Technical Service for assistance.

Step 1. Installing the airfoils

Position the fan upside-down on the provided foam work aid located inside the packaging as shown on the right. Remove the protective covering from the circuit board.

Moving clockwise around the fan, align each airfoil with a fan hub tab and firmly press it into place. Make sure that the colored stickers

match the colors of the stickers on the attachment of the fan hub.

Loosely secure the airfoils with the provided (6) airfoil screws. Once the airfoils are in position, fully tighten the screws to secure the airfoils to the fan hub.

tip!

Visit www.haikufan.com to view installation videos illustrating the airfoil installation process.

!

Be careful not to damage the circuit board while installing airfoils!

Haiku Bamboo

4

!

When installing the Bamboo airfoils, the edge of each airfoil should tuck under the airfoil next to it.

Haiku

tip!

To ease airfoil installation, the (3) motor top screws can be loosened. Do not forget to retighten them!

Motor top screw

©2012 DELTA T CORP. ALL RIGHTS RESERVED.

INSTALLATION (CONT.)

Step 2. Installing the lower cover

With the fan still positioned upside-down on the work aid, remove the protective covering from the bottom of the fan. With the fan still in the upside-down position, align the three tabs on the lower cover with the three slots in the undersides of the airfoils and secure.

Haiku Bamboo

For Haiku Bamboo, simply snap the lower cover to the bottom of the fan hub.

Lower

Cover

Haiku

For Haiku, position the lower cover, and then place both hands flat on the cover and turn clockwise to lock the lower cover into place.

Lower

Cover

Step 3. Installing rubber bumpers

Slide the rubber bumpers on the extension tube brackets as shown on the right.

Rubber bumper

HAIKU by Big Ass Fans

5

INSTALLATION (CONT.)

Step 4. Installing anchor bolts

Ensure wiring has been routed to the fan site. Drill four 8 mm holes. The hole depth should not exceed 40 mm.

Drill one 14 mm hole (for safety anchor hook) in the pattern shown below. The hole depth should not exceed 50 mm.

Remove any dust from the holes. Insert the (4) anchor bolts and (1) anchor hook into the pre-drilled holes. Strike the heads of the anchor bolts with a hammer, ensuring the bolt sleeves are flush with the ceiling surface. Make sure the anchor hook is fully tightenend.

08 mm

(Anchor Bolt)

40 mm

Concrete Ceiling

014 mm

(Anchor Hook)

80 mm

Step 5. Securing the mounting plate

Position the mounting plate on the (4) anchor bolts. Ensure all anchor bolts are fully tightened to expand and lock the anchors.

Step 6. Securing the safety cable

Attach one mounting bracket to the mounting plate, but do not fully tighten. Raise the fan to the mounting bracket and temporarily rest one rubber bumper in the space between the bracket and plate to help support the fan while securing the safety cable with the shackle.

Safety cable

Mounting bracket

6

©2012 DELTA T CORP. ALL RIGHTS RESERVED.

INSTALLATION (CONT.)

CAUTION: Disconnect power to the fan location before wiring the fan!

Step 6. Wiring the fan

With the fan hanging from the safety cable, connect the fan wires to the ceiling wires by twisting the ends together and securing them with a terminal strip. Refer to the wiring chart and diagram on the following page to determine the wire connections. Test the connection by tugging on the wires. Install the fan on a switched circuit so that you can turn off the fan using a wall switch in addition to using the remote control.

Step 7. Hanging the fan

Raise the fan to mounting bracket, and then insert one rubber bumper between the mounting plate and mounting bracket.

Position the fan, and then secure it with the other mounting bracket with the remaining mounting hardware. Tighten all hardware.

!

Be careful not to drop any hardware in the wiring cover during installation!

Mounting bracket

Step 8. Securing the wiring cover

Slide the wiring cover into position, allowing about a 1/8” (3 mm) gap to the ceiling. Rotate the wiring cover so that the mounting slots align with the screw holes. Secure the wiring cover screws on both sides of the extension tube to hold the cover in position. Make sure that there are no wires visible.

Slide the wiring cover trim up the extension tube, aligning the tabs on the inside of the ring with the slots on the bottom of the wiring cover. Twist clockwise to snap the wiring cover trim into position as shown.

tip!

If there is not enough clearance between the wiring cover and ceiling, the screw can be moved to the lower hole on the extension tube.

Wiring cover

Wiring cover trim

HAIKU by Big Ass Fans

7

INSTALLATION (CONT.)

Wiring diagram

Ensure power is disconnected before installing the fan!

WARNING: Do not connect the fan to a damaged power source! Do not attempt to resolve electrical failures on your own. Consult a qualified electrician if uncertain of the electrical installation of this fan.

Wire color chart

50/60 Hz Compatible

Fan Power Supply

Wire Color

Southeast Asia

220-240V System

AC Line (L1)

Brown

Brown, Black, or Grey

AC Line/Neutral (L2/N)

Blue

Earth/PE

(connected to fan chassis)

Green with Yellow Tracer

Blue Green with Yellow Tracer

Switched 100-240VAC 1Ф,

50-60Hz, 0.36A

PE / Earth Ground

AC Neutral / L2

AC Hot / L1

8

©2012 DELTA T CORP. ALL RIGHTS RESERVED.

Operation

Before using the Haiku remote control, remove the plastic tab in the battery tray.

!

The fan mode indicators are located on the bottom of the fan hub when viewed from the floor.

Remote Front

Powering the fan

To turn the fan on or off, press the On/Off button on the fan remote. This button can also be used to reset the fan’s speed. The remote must be pointing toward the fan mode indicators to function properly.

!

The fan will automatically restart at the last operating speed upon connection to the power source!

Replacing the remote control battery

The Haiku remote control operates on a CR 2025 3V lithium battery.

To

replace the battery, on the bottom of the remote, push the small tab to the right while sliding the battery tray outward. Replace the battery, and then close the battery tray. Recycle or dispose of the old battery properly.

Changing fan speed

Fan speed is increased or decreased by pressing the Up or Down

Speed button on the remote. Six fan speeds are available to accommodate your comfort level. Note: Seven speed indicators appear on the controller; however, only six are active on the fan.

To change the fan speed, press a Speed button. The Up Speed button increases fan speed; the Down Speed button decreases fan speed.

Press and hold a Speed button to step through the speeds automatically.

The fan mode indicators will illuminate and a short beep will be heard until speed 6 (high) or 0 (off) is reached.

Sleep mode

Sleep mode reduces the fan speed by one increment every hour until the lowest speed is reached. When the programmed time period ends, the fan automatically turns off. Sleep mode is only active when Timer mode

is used.

To activate Sleep mode, set the fan speed and Timer mode, and then press the Sleep button. The Sleep indicator will illuminate.

To exit Sleep

mode, press the Sleep, Clear, or On/Off button.

1.2” (33 mm)

Remote Back

Timer mode

In Timer mode, the fan runs at a set speed until the programmed time period ends. Note: Timer mode is disabled if the fan speed is 0 (off) or if the fan is not running.

To set Timer mode, press the Timer button 1–7 times (once for each hour) to program the end time.

During adjustment, the fan mode indicators will flash, and then the Timer setting is displayed on the speed indicator bar. To exit Timer mode, press the Clear button.

Whoosh mode

Whoosh mode simulates natural, relaxing breezes by automatically varying the fan speed in a quasisinusoidal pattern.

To activate Whoosh mode, set the desired maximum fan speed, and then press the Whoosh button.

The top Speed indicator will flash to indicate that Whoosh mode is active.

To exit Whoosh mode, press the Whoosh, Speed, or On/Off button once.

HAIKU by Big Ass Fans

9

OPERATION (CONT.)

Fan mode indicators

Each operating mode is indicated by a pattern on the fan mode indicator display, which is located on the bottom of the fan and is visible from the floor. The display includes an LED (light emitting diode) bar graph to indicate fan speed and Whoosh mode, and separate LEDs to indicate Timer mode and

Sleep mode.

All indicators automatically turn off approximately one minute after the last button is pressed to minimize power consumption and prevent nuisance lighting at night. The indicators will display the current speed setting by default. tip!

The indicators can be reactivated by pressing any button on the remote control except the On/Off button. This will not change the current operating setting.

Speed indicators

When the fan is running, the Speed indicator LEDs show the current fan speed (1–6). Whoosh mode is indicated when the highest set speed indicator is flashing. When all indicators are simultaneously flashing, Timer mode is active. Note: The controller shows seven speed indicators; however, only six are active on the fan.

You can toggle the display from Speed mode to Timer mode by pressing the Timer button once. To toggle from the Timer mode to Speed mode, simultaneously press the Speed button and Whoosh button once. See the previous page for instructions on changing fan speed.

Sleep mode indicator

The Sleep LED indicates that Sleep mode is active. A flashing Sleep LED indicates that the Timer mode is being adjusted. See the previous page for instructions on using Sleep mode.

Timer mode indicator

The Timer LED indicates that Timer mode is active. A flashing Timer LED indicates that the Timer mode is being adjusted. See the previous page for instructions on using Timer mode.

4

3

6

5

2

1 sleep timer

10

©2012 DELTA T CORP. ALL RIGHTS RESERVED.

Troubleshooting

WARNING: To avoid electric shock, remove power from the fan before servicing!

WARNING: Risk of fire, electric shock, or injury to persons during cleaning and servicing!

WARNING: Do not operate fan with missing or damaged components!

General troubleshooting

Some issues can be resolved before requesting service. Review the below troubleshooting tips before contacting Haiku Customer Service for support.

Symptom

The fan will not start.

The fan is noisy during operation.

The fan wobbles.

The fan does not produce airflow.

The fan jerks upon startup.

Possible Solution(s)

• Verify that supply power is adequate. Check your circuit breaker or fuse and wall switch for functionality.

• Check all mounting and fan hardware. If loose, tighten.

• For Haiku Bamboo fans, remove the airfoil to ensure the colored sticker matches the sticker on the fan hub. For

Haiku fans, remove the bottom cover and ensure the colored sticker on the bottom of the airfoil matches the sticker on the fan tab. If necessary, move the airfoils to the matching hub attachment points.

• Make sure that all mounting hardware is secure and tight.

• Make sure that all the airfoils are aligned properly and securely fastened to the fan hub.

• If an airfoil is damaged, contact Haiku Customer Service.

Note: Airfoils must be replaced as a set. Do not replace individual airfoils.

• If you installed multiple fans, ensure the serial numbers on the airfoils match the serial number on the fan hub.

• Make sure the airfoils are aligned properly.

• Make sure the fan is rotating counterclockwise when viewed from the floor.

• This is normal and may happen occasionally upon startup. An initial slight jerking forward and backward does not affect fan operation.

HAIKU by Big Ass Fans

11

Maintenance

WARNING: Disconnect the fan from power before servicing!

Annual maintenance

Please take a few moments each year to perform the following preventative maintenance procedures on your fan to ensure its safe and efficient operation. If you have any questions, require assistance with your fan, or need replacement parts, contact Haiku Customer Service at www.haikufan.com/ service.

Note: Actual fan setup may differ from the illustration below.

• Check that the safety cable is properly installed by sliding the wiring cover and trim down the extension tube, and then examining the safety cable and hardware.

• Make sure the mounting hardware is securely fastened.

• Make sure the hardware securing the airfoils to the fan hub is securely fastened.

• Dust the airfoils regularly. If the fan becomes dirty, clean it with a damp cloth and ordinary soap and water. Do not use solvents, gasoline, or any other chemical cleaners! These may cause surface distortion and damage to the fan.

• Make sure the wires are secure and the ground wire is securely connected.

Anchor

Hook

Safety cable

Wiring cover trim

Wiring cover

Airfoil

12

©2012 DELTA T CORP. ALL RIGHTS RESERVED.

Limited Lifetime Warranty

What this warranty covers

This Warranty covers the motor and other components of your Haiku ceiling fan against all defects in workmanship and materials. You must be the original purchaser or user of the Product to be covered.

The Limited Lifetime Warranty is subject to all provisions, conditions, limitations, and exclusions described within this document.

What is the period of coverage?

The Warranty Period commences on the date the Product is purchased. The Warranty Period for is two

(2) years for the motor, components, and accessories. Labor to repair the defect will be provided free of charge at our service center in the first year. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE OR SATISFACTORILY QUALITY, MADE WITH RESPECT TO

COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR.

What will we do?

During the Warranty Period, Big Ass Fan Company will, at its option and cost: a) Repair or replace the affected component(s) of any defective product; b) Repair or replace the defective product; or c) Refund the price you paid for the product upon return of the product to Big Ass Fan Company, shipping and insurance prepaid.

BIG ASS FAN COMPANY WILL SHIP THE REPAIRED PRODUCT OR REPLACEMENT TO YOU AT NO

CHARGE; HOWEVER, YOU ARE RESPONSIBLE FOR ALL COSTS OF REMOVAL, REINSTALLATION,

AND SHIPPING OF THE PRODUCT TO BIG ASS FAN COMPANY.

The foregoing constitutes your exclusive remedy and the limit of liability for Big Ass Fan Company, and for any and all losses in connection with this product.

What steps are required to obtain warranty service?

YOU MUST HAVE PROOF OF PURCHASE OF THE CEILING FAN TO OBTAIN LIMITED WARRANTY

SERVICE. KEEP YOUR RECEIPT OR OTHER PROOF OF PURCHASE.

Contact Haiku Technical Service Department as soon as possible after the issue is discovered by visiting our Web site at www.haikufan.com and submitting a Technical Support form, or calling

+65 6747 8857.

If the Haiku Technical Service Representative determines that the warranty claim may be valid and that a replacement part is required, the Representative will process the claim and the replacement part will be shipped to you. Included in the shipment of the replacement part will be any shipping labels and documents needed to return the original part including a Return Materials Authorization (RMA) number.

You will be responsible for all shipping insurance, freight, or other transportation charges to our service center. Your Haiku fan should be properly packed to avoid damage in transit since we will not be responsible for such damage.

What is not covered?

This warranty does not cover any defects, malfunctions, or failures caused by: a) Repairs by persons not authorized by Big Ass Fan Company; b) Use of parts and accessories not authorized by Big Ass Fan Company; c) Mishandling, improper installation, modifications, or damage to your ceiling fan while in your possession; or d) Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and tear.

HAIKU by Big Ass Fans

13

LIMITED LIFETIME WARRANTY (CONT.)

e) Any event beyond the control of Big Ass Fans and occurring after the Product is no longer in our control.

Additionally, this warranty ceases to apply when: a) The original purchaser or user ceases to own the product; or b) The product is moved from its original point of installation.

This warranty is only valid within the 50 states of the United States and the District of Columbia and the 10 Canadian Provinces and Territories. No other written or oral warranties apply, and no employee, agent, dealer, or other person is authorized to give any warranties on behalf of Big Ass Fan Company.

This warranty is only valid within Singapore and Malaysia. No other written or oral warranties apply, and no employee, agent, dealer or other person is authorized to give any warranties on behalf of Big

Ass Fans.

REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS

WARRANTY AND BIG ASS FANS IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING

INCIDENTAL AND CONSEQUENTIAL DAMAGES. Incidental damages include but are not limited to such damages as loss of time and loss of use. Consequential damages include but are not limited to the cost of repairing or replacing other property which was damaged if this product does not work properly.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED

OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE OR SATISFACTORY QUALITY,

AND OF ALL OTHER OBLIGATIONS AND LIABILITIES ON BIG ASS FAN COMPANY’S PART, AND

BIG ASS FAN COMPANY NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO ASSUME FOR

IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THE PRODUCTS. NO OTHER

WARRANTY EXPRESSED OR IMPLIED, WHETHER OF FITNESS FOR A PARTICULAR PURPOSE OR

OF MERCHANTABILITY OR OF SATISFACTORY QUALITY OR OF ANY OTHER KIND, WHETHER

OR NOT SIMILAR IN NATURE TO ANY PREVIOUSLY SPECIFIED, SHALL EXIST WITH RESPECT TO

SUCH PRODUCTS, ALL SUCH WARRANTIES BEING HEREBY WAIVED BY CUSTOMER, UNLESS

SUCH WARRANTIES CANNOT BE EXCLUDED BY LAW. UNDER NO CIRCUMSTANCES SHALL BIG

ASS FAN COMPANY BE LIABLE FOR ANY LOSS, DAMAGE, COST OF REPAIR, OR CONSEQUENTIAL

DAMAGES OF ANY KIND IN CONNECTION WITH THE USE, SALE, OR REPAIR OF ANY PRODUCTS

PURCHASED FROM BIG ASS FAN COMPANY, UNLESS SUCH DAMAGES CANNOT BE EXCLUDED BY

LAW.

Big Ass Fan Company reserves the right to change this warranty at any time without advance notice.

14

©2012 DELTA T CORP. ALL RIGHTS RESERVED.

www.haikufan.com

©2012 Delta T Corporation

002494

Installation Guide

S1