670AN3 - Alemlube
 Italiano................................Pagina
Español
.................................Página
9 33
...........Página 9
Includes Battery Charger
Français ................................. Page 17
and Carrying Case
Français .......... Page
17
OWNER’S
TECHNICAL MANUAL
Description
Deutsch ................................. Seite 25
670AN3
These model guns are designed to dispense
18V Cordless
Grease Gun 450g
Italiano................................Pagina
petroleum-based
greases (up to NLGI 2) for 33
general
lubrication applications. A 36-inch (0.91 meter) long
Description whip hose, heavy-duty grease coupler,
high-pressure
Description
Thesefast
model
guns are
dispense case are
1-hour
charger
anddesigned
moldedtocarrying
These model gunsgreases
are designed
to
dispense
petroleum-based
petroleum-based
(up
to
NLGI
2) for
general
included.
The
guns
arelubrication
equippedapplications.
with
low
battery
andgreases
(up
to
NLGI
2)
for
general
A
36-inch
lubrication applications. A 36-inch (0.91 meter) long
stall
indicator
lights andflexible
an LED
flashlight.
(0.91m)
long high-pressure
hose
extension, heavy-duty grease
high-pressure whip hose, heavy-duty grease coupler,
coupler, 1-hour fast charger and molded carrying case are included.
1-hour
charger
carrying
case are
Thefast
guns
use aand
18molded
V motor
with three
stages of gear
included. The
guns
are and
equipped
with
low batterydrives
and
reduction.
crank
mechanism
The guns areAequipped
with yoke
low battery
and stall indicator a
lights and
stall
indicator
lights
and
an
LED
flashlight.
an LED flashlight. The guns use a 18V motor with three stages of gear
reciprocating piston pump. The motor is powered by a
reduction.
A crank
andVyoke
mechanism
drives
a reciprocating
piston
The guns
use18
a 18
with
three
stages
of gearbattery
rechargeable
Volt motor
/ 3000
mAh
Lithium-ion
pack.
pump. The motor is powered by a rechargeable 18V / 3000 mAh
reduction. A crank and yoke mechanism drives a
Lithium-ion battery pack. Includes 2 18V batteries as standard.
Each model
gun
is designed
3-way loading;
reciprocating
piston
pump.
The motorfor
is powered
by a
rechargeable
18 Volt /and
3000loader
mAh Lithium-ion
batteryoptional
pack.
cartridge,
suction,
pump (requires
Each model gun is designed for 3-way loading; cartridge, suction, and
Mode l
loader
fitting
322610).
Theloader
guns
are 322610).
spring-primed
loader
(requires
fitting
are
Eachpump
model
gun isoptional
designed
for 3-way
loading;The guns and
spring-primed
and
include
an
air
bleed
valve
to
aid
priming.
include
air bleed
valve pump
to aid(requires
priming.
cartridge,an
suction,
and loader
optional
loader fitting 322610). The guns are spring-primed and
include an air bleed valve to aid priming.
595-A
Optional
Accessories
Optional Extras
Accessories
Optional
Mobile Battery
Shoulder
Charger
Tool Bag
Mobile Battery
Strap Shoulder
(12 Vdc to 18 Vdc) Loader
Tool Bag
Strap
339812
340057
339812
Charger
(12 Vdc to 18 Vdc)
Fitting
343154
343154
340057
595-B
Loader
Fitting
322610
322610
Specifications
Specifications
Specifications
Maximum Maximum
Flow
Flow
RateRate
Pressure
Pressure
psi
psi
bar
8,000
552
8,000
bar
552
Oz./Min. Gms/Min.
6
170
170
595-C
Batte ry
1
595-B
(North / South America
2
595-C
1
1
595-D
595-D
Cartridges
2724
27
Sound pressure (LpA) 72.3 dB(A), uncertainty (K) 3 dB(A)
) 83.3
dB(A),
uncertainty
(K) 3(K)
dB(A)
Acousticpressure
power (L(L
Sound
(LpA)
dB(A),
uncertainty
3 dB(A)
) 72.3
dB(A),
uncertainty
(K)
3 dB(A)
Sound
WApA
2 , uncertainty (K) 1.5 m/s2
Vibration
emission
value
(a
)
0.6
m/s
h
Acoustic power (LWA) 83.3 dB(A), uncertainty (K) 3 dB(A)
230 V
(Euro
230
2 Vac / 50 Hz
(Europe / Middle East)
2
Figure 1 Cordless Grease Gun Mode
Figure 1 Cordless Grease Gun Models 595-A,-B,-C,-
Cartridges
Ba
1Batte ry C harge r
120 V
(Nort
2
120 Vac / 60 Hz
595-A
Q uantity
Hose Length Grease
CylinderHose
Capacity
Grease Cylinder
Capacity
Length
Delivery
when
Delivery
CapacityCapacity
when
Cartridge
Cartridge
Fully Charged
Fully Charged Bulk
Length
Bulk
Size
Size
Oz./Min. Gms/Min.
6
Batte ry
Q uantity
Mode l
Ounces Gms
Ounces
Ounces Gms
16
454
16
14
454
Weight
(Empty)
Length
Inches Meters
Ounces
36
14
Lbs
Kg
7.2
3.3
Inches Meters
0.91
36
0.91
Acoustic power (LWA) 83.3 dB(A), uncertainty (K) 3 dB(A)
Vibrationemission
emissionvalue
value(ah)
(a h)0.6
0.6m/s2,
m/s2,uncertainty
uncertainty(K)
(K)
m/s2
Vibration
1.51.5
m/s2
Alemite, LLC
167 Roweland Drive, Johnson City, Tennessee 37601
Alemite, LLC
www.alemite.com
167 Roweland ©Drive, Johnson City, Tennessee 37601
Copyright 2011 by Alemite, LLC
www.alemite.com
671018
671018
NSW
TEL: (02) 9939 0711
FAX: (02) 9939 0411
This document contains confidential information that is the pr operty of Alemite, LLC
©
and is not to be copied, used, or disclosed
to others
without
written
Copyright
2011
by express
Alemite,
LLCpermission.
VIC/TAS
TEL: (03) 8787 8288
FAX: (03) 8787 8266
WA
TEL: (08) 9209 3066
FAX: (08) 9209 3933
SA/NT
TEL: (08) 8241 7111
FAX: (08) 8241 7011
Visit our website at www.alemlube.com.au or www.alemlube.co.nz
Lbs
7.2
SER 595
Revision (10-
This document contains confidential information that is the pr operty of Alemite, LLC
and is not to be copied, used, or disclosed to others without express written permission.
QLD/PNG
TEL: (07) 3204 9166
FAX: (07) 3204 1224
W
(E
NZ
TEL: (09) 447 1007
FAX: (09) 447 1008
Parts And Drawing Breakdown For The 670AN3
SER 595‐A
Cordless Grease Gun
NSW
TEL: (02) 9939 0711
FAX: (02) 9939 0411
QLD/PNG
TEL: (07) 3204 9166
FAX: (07) 3204 1224
VIC/TAS
TEL: (03) 8787 8288
FAX: (03) 8787 8266
WA
TEL: (08) 9209 3066
FAX: (08) 9209 3933
SA/NT
TEL: (08) 8241 7111
FAX: (08) 8241 7011
Visit our website at www.alemlube.com.au or www.alemlube.co.nz
NZ
TEL: (09) 447 1007
FAX: (09) 447 1008
2
Parts And Drawing Breakdown For The 670AN3
Cordless Grease Gun
SER 595-A
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Insert, Coupler (
Housing Cover
Washer, Lock
Screw, Machine
Screw, Tapping
Trigger
Screw, M3 x 6
Washer, M3, Lo
Cover, Head
Ring, Retaining
Washer, 0.24 ID
Q31631-35.SLD
Q31631-36.SLD
Washer, 0.24 ID
Gear Assembly,
coupler holster
Head & Bearing
Trigger Spring
Gear, Internal
Q31631-25.SLD
Q31631-23.SLD
Q31631-21.SLD
Q31631-19.SLD
Q31631-15.SLD
Washer, kcoL
21.SLDPRT
Screw, M3 x 16
393795-19*
Insert, Coupler (Rubber)
Housing, Right
Washer, Lock
Screw, Machine
Screw, Tapping
Trigger
Screw, M3 x 6
Washer, M3, Lock
Cover, Head
Ring, Retaining
Washer, 0.24" ID x 0.67" OD
Yoke
Bearing, Roller
Washer, 0.24" ID x 0.59" OD
Gear Assembly, Output
Holster
Head & Bearing Assembly
Trigger Spring
Gear, Internal
Gear, Output Pinion
Gear, Planet (Second Stage)
Gear, Sun (Second Stage)
Gear, Planet (First Stage)
Washer
Washer, kcoL
Mount, Motor
Screw, M3 x 16
Motor Assembly (with Sun Gear)
29
343151
Battery Pack, 18V
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
339820
Switch, Three W
336523
Q31631-53.SLD
Spring, Bleed V
Valve, Bleed
Plug
Piston
Pin, Roll
340067
308730
343170
Lens Support
PCB board
Ball, Check, 3-8
Spring, Check
Gasket (Copper)
Plug, Check
TP
PCB
Housing ASSY
343152
343153
Cylinder Assembly, Grease
Switch
Gasket
O-Ring
Spring, Bleed Valve
Valve, Bleed
Plug
Piston
Pin, Roll
Hose Assembly, Grease
Coupler, Grease
Flashlight with Clip
Lens, LED
Circuit Board, LED
Ball, Check, 3/8" Diameter
Spring, Check
Gasket (Copper)
Plug, Check
Protector, Thermal
Circuit Board and Battery Connector
Housing, Left
Charger, Battery (120 Vac / 60 Hz)
Charger, Battery (230 Vac / 50 Hz)
Case, Carrying
51
52
Qty
1
1
10
8
4
2
6
4
1
2
1
1
1
1
1
1
1
1
1
1
3
1
3
1
2
1
5
1
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
393795-12 Head*
Description
393795-20
Electronic Circuitry*
Part No.
393757 Bleed Valve
Item No.
393795-6 Ball Check
Repair Kits
Notes
•
•
Models 595-A, -C
Models 595-B, -D
•
•
•
•
•
•
Never Substitute
•
•
•
•
•
•
•
•
Models 595-A, -B
Models 595-C, -D
Optional
A
340338
Relief Valve with Gasket
B
6304-B
Coupler, Grease
Legend:
Part numbers left blank are not available separately.
*Replacement of these items by other than an authorized Alemite Service Center voids the warranty.
NSW
TEL: (02) 9939 0711
FAX: (02) 9939 0411
Alemite, LLC
QLD/PNG
TEL: (07) 3204 9166
FAX: (07) 3204 1224
VIC/TAS
TEL: (03) 8787 8288
FAX: (03) 8787 8266
WA
TEL: (08) 9209 3066
FAX: (08) 9209 3933
SA/NT
TEL: (08) 8241 7111
FAX: (08) 8241 7011
Visit our website at www.alemlube.com.au
or www.alemlube.co.nz
3
NZ
TEL: (09) 447 1007
FAX: (09) 447 1008
Revision (10-11)3
General Safety Rules
WARNING
Read all instructions: Failure to follow all instructions listed below may result in electric shock,
fire and/or serious injury. Save these instructions.
Work Area
• Keep work area clean and well lit. Cluttered and dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids,
gases or dust. Power tools create sparks which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control. Electrical Safety
•
•
•
•
•
•
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric
shock.
Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of
electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of
electric shock.
When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.
Personal Safety
• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a
power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in serious personal injury.
• Use personal protective equipment. Always wear eye protection. Safety equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power
source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on
the switch or energising power tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached
to a rotating part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and collection facilities, ensure these are
connected and properly used. Use of these devices can reduce dust related hazards.
Revision (10-11)
NSW
TEL: (02) 9939 0711
FAX: (02) 9939 0411
Alemite, LLC
4
QLD/PNG
TEL: (07) 3204 9166
FAX: (07) 3204 1224
VIC/TAS
TEL: (03) 8787 8288
FAX: (03) 8787 8266
WA
TEL: (08) 9209 3066
FAX: (08) 9209 3933
SA/NT
TEL: (08) 8241 7111
FAX: (08) 8241 7011
Visit our website at www.alemlube.com.au or www.alemlube.co.nz
NZ
TEL: (09) 447 1007
FAX: (09) 447 1008
SER 595-A
Cordless Grease Gun
General Safety Rules (Continued)
WARNING
Read all instructions: Failure to follow all instructions listed below may result in electric shock,
fire and/or serious injury. Save these instructions.
Power Tool Use and Care
• Do not force the power tool. Use the correct power tool for your application. The correct power tool
will do the job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn it on and off. Any power tool that can not be
controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source before making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures reduce the risk of starting the power tool
accidentally.
• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool. Power tools are dangerous in the hands of
untrained users.
• Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any
other condition that may affect the power tools operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the
manner intended for the particular type of power tool, taking into account the working conditions and
the work to be performed. Use of the power tool for operations different from intended could result in a
hazardous situation.
Battery Use and Care
• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with another battery pack.
• Use power tools only with specifically designated battery packs. Use of any other battery packs may
create a risk of injury and fire.
• When battery pack is not in use, keep it away from other metal objects like paper clips, coins,
keys, nails, screws, or other small metal objects that can make a connection from one terminal to
another. Shorting the battery terminals together may cause burns or a fire.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
• Disconnect battery pack from gun before changing accessories, storing gun or unscrewing
grease cylinder from the gun.
• Ensure the switch is in the off position before inserting battery pack. Inserting the battery pack into
power tools that have the switch on invites accidents.
• Never attempt to open the battery pack for any reason.
• Do not expose the battery pack to water.
• Do not store the battery pack in locations where the temperature may exceed 104° F (40° C).
• Charge the battery pack only at ambient temperatures between 40° F (4° C) or above 104° F (40° C).
Service
• Have your power tool serviced by a qualified repair person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
NSW
TEL: (02) 9939 0711
Alemite,
FAX: (02)LLC
9939 0411
QLD/PNG
TEL: (07) 3204 9166
FAX: (07) 3204 1224
VIC/TAS
TEL: (03) 8787 8288
FAX: (03) 8787 8266
5
WA
TEL: (08) 9209 3066
FAX: (08) 9209 3933
SA/NT
TEL: (08) 8241 7111
FAX: (08) 8241 7011
Visit our website at www.alemlube.com.au or www.alemlube.co.nz
NZ
TEL: (09) 447 1007
Revision
(10-11)
FAX: (09) 447
1008
SER 595-A
Specific Safety Rules
Suction Loading
1. Unscrew Grease Cylinder (30) from gun.
Cordless Grease Gun
WARNING
2. Insert the head of the Grease Cylinder below the
surface of the grease.
The gun can develop high pressure up to
8,000 psi (552 bar). Rupture of components can
inject grease into skin and eyes, causing serious
injury and possible amputation. If injured, seek
immediate medical attention.
3. Slowly pull the follower rod outward from the Grease
Cylinder cap until the groove is visible.
4. Engage the groove in the follower rod with the slot in
the Grease Cylinder’s cap.
Do not operate without proper safety protection,
gloves, and goggles. Hold hose at spring guard
only. Do not use if hose is damaged or worn.
Inspect hose before each use. Use only Alemite
340067 Grease Whip Hose.
5. Screw the Grease Cylinder onto the gun.
6. Disengage the follower rod from the slot in the Grease
Cylinder cap.
• Push the follower rod into the Grease Cylinder.
This gun uses lubricants, that may be flammable
and poisonous if ingested. Do not use gun near
open flame or other fire hazards. Read all
warnings on lubricants before using this gun.
Loader Pump
Use ear protection to reduce the risk of induced
hearing loss.
WARNING
The gun can be equipped with an optional
low-pressure Loader Fitting. Do not substitute with
a high-pressure grease fitting. Personal injury can
occur due to excessive pressure.
Disconnect battery pack from gun before changing
accessories or storing the gun.
Warning! To reduce the risk of inj ury, the
user must read the instruction manual.
The use of a grease fitting will void the warranty.
Separate collection. This product must not be
disposed of with normal household waste.
CAUTION
The Loader Fitting on the gun must mate with the
loader coupler. The pump may not operate if the
components are not compatible.
Loading and Priming the Gun
NOTE: Refer to Figure 2 for component
identification on the following procedures.
Cartridge Loading
1. Unscrew Grease Cylinder (30) from the gun.
2. Pull the follower rod and engage the groove in the
follower rod with the slot in the Grease Cylinder cap.
3. Remove the plastic cap from the cartridge.
4. Apply a film of grease to the exposed inside surface of
the cartridge.
NOTE: This is only necessary for a virgin
gun.
1. Pull the follower rod and engage the follower by
rotating the rod.
2. Seat the Loader Fitting into the loader coupler.
• Push down to hold the coupler valve open.
3. Operate the pump and view the movement of the
follower rod.
4. Discontinue pump operation once the groove on the
follower rod is visible.
5. Disengage follower rod from follower and push into
the Grease Cylinder.
5. Insert the cartridge into the Grease Cylinder.
• Remove the tabbed seal from the cartridge.
6. Screw the Grease Cylinder onto the gun.
7. Disengage the follower rod from the slot in the Grease
Cylinder cap.
• Push the follower rod into the Grease Cylinder.
Revision
NSW
(10-11)
TEL: (02) 9939 0711
FAX: (02) 9939 0411
QLD/PNG
TEL: (07) 3204 9166
FAX: (07) 3204 1224
VIC/TAS
TEL: (03) 8787 8288
FAX: (03) 8787 8266
6
WA
TEL: (08) 9209 3066
FAX: (08) 9209 3933
SA/NT
TEL: (08) 8241 7111
FAX: (08) 8241 7011
Visit our website at www.alemlube.com.au or www.alemlube.co.nz
NZ
Alemite,
LLC
TEL: (09) 447 1007
FAX: (09) 447 1008
SER 595-A
Cordless Grease Gun
Priming the Gun
In most cases the gun will prime simply by
operating the Trigger several times.
Should grease fail to appear, air must be bled.
Force Prime
This process manually assists air within the gun to
be bled at the Bleed Valve.
1. Pull the follower rod and engage the follower by
rotating the rod.
2. Depress Bleed Valve (35) and at the same time
push on the follower rod.
Once the air is eliminated, operate the gun several
times.
Once grease appears, disengage the follower rod
from the follower and push into the Grease Cylinder.
Gun Operation
Battery Pack (29) is intentionally shipped with a
low charge.
Charge Battery Pack prior to use.
• Refer to the following section for details.
The battery needs to be charged before first use
and whenever it fails to produce sufficient power
on jobs that were easily done before. The battery
may become warm while charging; this is normal
and does not indicate a problem.
Low Battery Indicator
The low battery indicator illuminates when there
is sufficient battery charge to dispense approximately
three cartridges of grease.
Stall Indicator
The stall indicator illuminates when a stall
condition causes the thermal protector to
open. Release the trigger to turn off the stall
indicator. The thermal protector resets
automatically.
NSW
LLC
TEL: (02) 9939 0711
Alemite,
FAX: (02) 9939 0411
QLD/PNG
TEL: (07) 3204 9166
FAX: (07) 3204 1224
VIC/TAS
TEL: (03) 8787 8288
FAX: (03) 8787 8266
CAUTION
Air pockets in the grease can cause the gun to lose
prime. Check for prime after each refill and before
lubrication.
The gun is equipped with a thermal protector to
prevent the motor from overheating. When a blocked
bearing, line, or grease fitting causes the gun to stall,
the thermal protector will open.
For maximum motor life, avoid operating at stall
Check Valve Contamination
Should the gun fail, the outlet check may be held
open. Remove Plug (47), clean Ball (44), and the Ball
seat of Head (17).
Battery Pack and Charger Safety Rules
This manual contains important safety and operating
instructions for Battery Pack part number 343151 and Battery
Chargers 343152 and 343153.
WARNING
Before using the Battery Charger read all
instructions and cautionary markings on Battery
Charger (51), Battery Pack (29), and products using
the Battery Pack.
To reduce the risk of injury, charge only Lithium-ion
type rechargeable batteries. Other types of batteries
may burst causing injury.
An extension cord should not be used unless absolutely necessary. Use of an improper extension cord
could result in a risk of fire and electric shock. If an
extension cord must be used, make sure it is 18gauge. Check to ensure that the pins on the plug of
the extension cord are the same number, size, and
shape as those of the plug on the Charger. Make sure
that the extension cord is properly wired and in good
electrical condition.
Do not incinerate the Battery Pack, even if it is
severely damaged or completely worn out. The Battery
Pack may explode in fire.
7
WA
TEL: (08) 9209 3066
FAX: (08) 9209 3933
SA/NT
TEL: (08) 8241 7111
FAX: (08) 8241 7011
Visit our website at www.alemlube.com.au or www.alemlube.co.nz
NZ
Revision
(10-11)
TEL: (09) 447 1007
FAX: (09) 447 1008
SER 595-A
Cordless Grease Gun
Battery Charger Operation
CAUTION
Do not expose the Charger to rain, snow, or frost.
Charge the Battery only with the Charger provided.
Make sure power circuit voltage is same as that shown
on the charger specifications plate. Press down to ensure
the battery properly engages with the charger’s contacts.
To reduce the risk of damage to electric plug and
cord, pull by the plug rather than the cord when
disconnecting the Charger.
Make sure the cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
Do not operate the Charger with damaged cord or plug.
Replace immediately. Do not operate the Charger if it has received a
sharp blow, been dropped, or otherwise damaged
in any way.
Do not disassemble the Charger.
Do not charge the Battery when the temperature
is below 40° F (4° C) or above 104° F (40° C).
The Charger is designed to operate on standard
household electrical power. Do not attempt to use
it on any other voltage.
Consecutive charging may cause overheating. If
you need to recharge the Battery consecutively,
wait for about 15 minutes to allow the Charger
to cool.
Red Light Flash
When the charger is powered on, the Red light
will flash once.
Green Light Flashing
Charging
Green Light On
Battery fully charged
Red Light Rapid Flashing at 4HZ
Battery will not charge
Red Light Slow Flashing at 1HZ
Battery too hot. Charging will restore when the
battery pack cools down to 104° F (40° C).
Battery overheating could be attributed to:
A. Long continuous running
B. Hot ambient temperature
C. One or more cells are damaged
1 hour of charge time is required to fully
charge the battery.
The Battery will become slightly warm to the
touch while charging. This is normal and does not
indicate a probl em.
Do not insert foreign material into the hole for the
Battery in the Charger stand.
Do not disassemble the Battery.
Do not Store the gun and Battery assembly
in locations where the temperature may reach or
exceed 104° F (40° C).
Do not short-circuit the Battery.
Function of Red and Green Lights
Do not place the Charger in an area of extreme heat
or cold. It works best at normal room temperature.
Changes Since Last Printing
BOM & Parts List Revisions
Revision (10-11)
NSW
TEL: (02) 9939 0711
FAX: (02) 9939 0411
Alemite, LLC
8
QLD/PNG
TEL: (07) 3204 9166
FAX: (07) 3204 1224
VIC/TAS
TEL: (03) 8787 8288
FAX: (03) 8787 8266
WA
TEL: (08) 9209 3066
FAX: (08) 9209 3933
SA/NT
TEL: (08) 8241 7111
FAX: (08) 8241 7011
Visit our website at www.alemlube.com.au or www.alemlube.co.nz
NZ
TEL: (09) 447 1007
FAX: (09) 447 1008
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising