Announces the NEW Symbol DS3408 DPM/UID Imager!
Announces the NEW Symbol DS3408 DPM/UID Imager!
Reads All Bar Codes and Direct Part Marks (DPM/UID) Automatically!
The all new DS3408 DPM Series industrial DPM/UID readers from Symbol Technologies use digital signal processing (DSP)
CCD imaging technology to accurately read laser, dot peen marked, chemical etch and other types of direct part
markings at distances from 1” to 12” or more. In addition the DS3408 reads all types of two-dimensional (2D) and
one-dimensional (1D) printed bar codes automatically.
A Non Contact DPM/UID High Performance Reader with Variable Focus!
The DS3408 DPM comes equipped with newly designed charge-coupled device (CCD) image sensor and special direct part
mark reading software, which allow it to more accurately capture and process DPM at speeds, angles and distances never
before seen in a DPM/UID reader. With Symbol’s patented variable focus technology, you are able to read DPM at
ranges from 1” to over 12” automatically without refocusing. In addition, the DS3408 DPM’s omni-directional
reading functionality lets operators quickly capture both DPM/UID marks and bar codes from any angle,
eliminating the need to read DPM/UID straight on. The DS3408 DPM has the widest working range of any DPM
Reader in its class. Its smart focus technology, unique to Symbol, allows you to read DPM/UID marks and bar codes
regardless of the size or density of the code from a variety of distances automatically. This means that this single device
can work well for all your DPM/UID and barcode scanning needs.
Reads Very Low Contrast and Poorly Marked DPM/UID With Ease!
Because the DS3408 DPM uses Digital Signal Processing (DSP) CCD technology instead of cameras to read DPM/UID
marks, the DS3408 DPM can easily distinguish and read very low contrast or poorly marked DPM/UID marks with ease.
No other camera based DPM reader on the market today can make that claim! In addition the DS3408 DPM can read
DPM/UID marks as tiny as 4 mil to more than 12 inches or more in size. Because of Symbol’s extensive bar code reading
knowledge acquired from years of being the world’s largest manufacturer of bar code reading devices, the DS3408 DPM
can read pin marked DPM/UID marks easily from angles as steep as 80 degree tilt away from
perpendicular! Other camera based imagers can only read at a 7 degree tilt.
Best of all, by using DSP technology to read DPM/UID marks on the DS3408 DPM, we are able to offer a reader that is
priced significantly less than our competition while providing much higher performance on all UID/DPM marks.
Corporate Office - 10370 Citation Dr Suite 200 - Brighton, MI 48116 - P 810.227.3737 - F 810.227.3909
www.freedomcorp.com
DS3408 DPM Specification Highlights
Physical Characteristics
Dimensions
7.34 in. H x 4.82 in. W x 2.93 in. D 18.65 cm H x 12.25 cm W x 7.43 cm D
Weight (without cable)
12.56 oz./356 gm
Input Voltage
5 volts +/- 10%
Operating Current
250mA (average)
Depending on host:
- Host power
- External power supply
Power Sources
Color
Twilight Black/Yellow
Performance Characteristics
Light Source
650 nm visible laser diode
Resolution
640 x 480
Minimum Element Width
5 mil/0.127 mm
Nominal Working
Distance
From 1 in./ 2.5 cm to 14 in. /35 cm on 100% UPC/EAN symbols
Print Contrast
15% minimum reflective difference or less
Roll (Tilt) 1
+/- 180 degrees from normal
2
+/- 60 degrees from normal
Skew (Yaw) 3
+/- 50 degrees from normal
Pitch
Decoding Capability
1D Codes
UPC.EAN, UPC.EAN with Supplementals, UCC.EAN 128, JAN 8 & 13, Code 39, Code 39 Full ASCII, Code 39 Trioptic, Code 128, Code 128
Full ASCII, Codabar (NW7), Interleaved 2 of 5, Discrete 2 of 5, Code 93, MSI, Code 11, Code 32, Bookland EAN, IATA, UCC/EAN RSS and
RSS variants
2D Codes
Direct Part Marking (DPM/UID) PDF417, microPDF417, MaxiCode, DataMatrix (ECC 2000), Composite Codes, QR Code
Postal Codes
U.S. Postnet, U.S. Planet, U.K. Postal, Japan Postal, Australian Postal, Dutch Postal
Interfaces Supported
RS232, Keyboard Wedge, Wand Emulation, Scanner Emulation, IBM 468X/469X, USB and Synapse
User Environment
Operating Temperature
32° to 122° F/0° to 50° C
Storage Temperature
-40° to 158° F/-40° to 70° C
Humidity
5% to 95% relative humidity, noncondensing
Drop Specifications
Unit functions normally after repeated 6.5 ft./2 m drops to concrete
© 2006Copyright Freedom Technologies. All Rights Reserved.
Corporate Office - 10370 Citation Dr Suite 200 - Brighton, MI 48116 - P 810.227.3737 - F 810.227.3909
www.freedomcorp.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising