RL Flo - Cobb Carpet Supply

RL Flo - Cobb Carpet Supply
IF YOU HAVE QUESTIONS OR CONCERNS, OR ARE MISSING PARTS...
DO NOT RETURN SPRAYER TO THE STORE!
PLEASE CALL OUR CONSUMER HOTLINE AT 1-800-253-4642
Year-round Mon.-Fri., 8 a.m. - 7 p.m. ET
March 1 – August 31 Sat. and Sun. 10:00 a.m. to 4:00 p.m. ET
Or write us at: Root-Lowell Manufacturing Co. • 1000 Foreman Rd.
P.O. Box 289 • Lowell, MI 49331
Visit us on the Internet at: http://www.rlflomaster.com
e-mail: service@rlflomaster.com
OPERATION AND SERVICE INSTRUCTIONS
LAWN & GARDEN POLYMER SPRAYERS
with Funnel Top Tank Openings
MODELS: 1401, 1401HD, 1402, 1403, 1996, 2301, 2302, 2302F, 2303, 2401, 2402, 9001, 1001, 1002, 1003, 1025HD, 1101,
1102, 1102D, 1125D, 7015, 1215
WARNING!!! THIS PRODUCT IS DESIGNED TO SPRAY CHEMICALS THAT MAY BE HARMFUL AND COULD CAUSE
SERIOUS PERSONAL INJURY IF INHALED OR BROUGHT INTO CONTACT WITH THE USER. FAILURE TO READ AND
FOLLOW OPERATING INSTRUCTIONS BEFORE USE AND/OR MISUSE OF THIS PRODUCT COULD RESULT IN EXPLOSIVE FAILURE WITH MAJOR INJURIES.
•
•
•
•
•
•
•
•
•
ALWAYS water test unit before using.
ALWAYS wear protective clothing, eye protection, and gloves.
ALWAYS READ AND FOLLOW label instructions for chemicals to be applied.
AFTER USE - release pressure, empty, and clean the sprayer.
RELEASE pressure in sprayer before servicing.
DO NOT alter sprayer.
DO NOT spray gasoline or other flammables.
DO NOT store liquids in tank.
DO NOT leave sprayer in the sun.
INITIAL ASSEMBLY INSTRUCTIONS:
1.Be sure to first insert pink siphon tube into hose insert otherwise sprayer will not operate.
2.Lubricate (with grease or petroleum jelly), the o-ring on the hose insert and slide into tank until fully seated.
3.Slide tank nut to threaded connection and securely screw onto tank.
4.Attach the flow control to the hose by unscrewing the flow control nut from the back of the flow control. Slide it directly onto
the end of the hose.
5.Push the hose onto the back of the flow control all the way past the barb and up to the threads and screw together. Hand
tighten only.
6.Push the extension rod into the flow control until it stops. Slide extension nut o-ring to the flow control and screw together.
Hand tighten only.
!OPERATING INSTRUCTIONS:
1.Remove the pump from the tank by turning counter clockwise.
2.Prepare spray solution following instructions provided with the chemicals. For best results, mix in a separate container and
strain through cloth sieve when pouring into tank. Do not fill tank above the maximum fill marker.
3.Close tank by inserting pump assembly through opening. Turn clockwise until pump is sealed tightly into tank.
4.When the sprayer is filled, 20-30 strokes on the pump should supply enough pressure for spraying. More strokes will be
needed if tank is only partially filled. As the fluid level goes down, more strokes may be needed. To work the pump,
unlock pump handle from pump cap by turning counter clockwise. Lock the handle again by turning clockwise.
5.To start spraying, squeeze the flow control lever. Release pressure from the lever and
the spray will stop. To spray continuously, squeeze the lever, and slide the lock forward.
See Figure.
6.If your sprayer has an adjustable cone nozzle, screw it in clockwise for a fine mist, and counter clockwise for a coarse
stream. Flat fan nozzles are not adjustable.
7.To depressurize the tank, turn the tank upside down. Squeeze the flow control lever until all air pressure is gone. If your
sprayer has a pressure relief valve, pull up on the valve stem.
WARNING!!! To prevent ejected pump assembly and/or solution from striking and injuring you, never stand with
face or body over the top of the tank when pumping or loosening pump.
8.Empty any remaining solution into a proper storage container or disposal container. Do not store chemicals in the tank. If the
chemical is stored in the tank, it can clog the system as it dries and can promote corrosion.
9.Clean the sprayer after each use to prolong its life. After using water-based products, rinse thoroughly with water, being sure
to flush out hose and flow control. After spraying solvent or oil-based products, follow chemical manufacturer’s recommended
cleaning procedure.
10.To store the sprayer, hang the tank upside down with the pump removed and the flow control locked “on”. This allows for
proper drainage and drying.
11.Check for worn or damaged parts frequently.
!
MAINTENANCE AND DISASSEMBLY:
To keep the pump working smoothly and efficiently, the plunger u-cup seal needs
to be lubricated often. Disassemble pump, according to the instructions below,
and apply grease or petroleum jelly around the outside of the plunger cup. Note:
Your sprayer was lubricated at the time of manufacture.
To disassemble pump, lay pump down on table.
With a flat blade screwdriver, push in on the tabs
on each side of the pump and pry down. Pull up
on the handle and the plunger assembly should
come out of the pump cylinder. To reassemble,
insert plunger assembly into cylinder and push the
tabs back into place. See Figure.
! TROUBLESHOOTING: Always depressurize the sprayer, remove chemical solution, and clean the sprayer before making
repairs. Refer to the parts diagram for part numbers and names. Replacement parts may be purchased at most RL FLOMASTER dealers, or they can be ordered from our Consumer Service Hotline at 1-800-253-4642.
PROBLEM: Pump works hard or does not pressurize tank.
CAUSE: Plunger cup or plunger o-ring either not lubricated or damaged.
SOLUTION: Apply petroleum jelly around outside of plunger cup or plunger o-ring. Check for cracks or other damage and
replace if necessary.
PROBLEM: Spray solution backs up through pump cylinder.
CAUSE: Check valve on bottom of pump cylinder prevented from sealing by dirt, residue, or damage.
SOLUTION: Remove pumps cylinder and examine check valve. Clean if dirty. Replace if damaged.
PROBLEM: Hose leaks at tank connection.
CAUSE: (1) Hose/tank screw connector loose OR (2) Hose damaged.
SOLUTION: (1) Tighten screw connector - hand tighten only. OR (2) Cut off damaged section of hose and reassemble with
gear clamp, or replace with new hose/flow control assembly.
PROBLEM: Flow control leaks.
CAUSE: (1) Extension o-ring prevented from sealing by dirt or damage OR (2) Extension nut not screwed in all the way on flow
control.
SOLUTION: (1) Clean and examine o-ring, replace if damaged OR (2) Push extension into flow control until it is fully seated
into place. Then screw extension nut into flow control. Hand tighten only.
PROBLEM: Bad spray pattern or low spray volume.
CAUSE: Extension nozzle clogged with dirt or damaged.
SOLUTION: Remove nozzle and clean. Remove extension and clean. If extension cannot be unclogged, replace it.
PROBLEM: Nozzle leaks when flow control is closed.
CAUSE: (1) Extension o-ring prevented from sealing by dirt or damage. OR (2) Nozzle is worn.
SOLUTION: (1) Clean and examine o-ring, replace if damaged. OR (2) Replace nozzle cap.
PROBLEM: Leak at tank opening.
CAUSE: (1) Pump cylinder not sealed tightly into tank OR (2) Damaged cylinder gasket or o-ring.
SOLUTION: (1) Apply grease or petroleum jelly to cylinder gasket. OR (2) Thoroughly clean cylinder gasket or o-ring and
surrounding area then apply grease or petroleum jelly to cylinder gasket. OR (3) Replace with new gasket or o-ring.
PROBLEM: Tank leaks around or through pressure release valve (does not apply to all models).
CAUSE: (1) Valve prevented from closing properly by dirt or residue. OR (2) Valve assembly not screwed in completely. OR
(3) Valve gasket prevented from sealing by residue, dirt, or damage.
SOLUTION: (1) Pull up on valve stem several times, allowing it to snap back into place. OR (2) Screw in valve assembly
tightly. OR (3) Unscrew valve from tank and examine the gasket. Clean if dirty, replace if damaged.
REPAIR PARTS
PUMP ASSEMBLY
MODELS
1401, 1402,1401HD,
1403,2401, 2402,
1101, 1102,9001,
1102D, 1215
MODELS
2301, 2301F,1001
2302,2302F,1002
2303,1003, 1996
1025HD
Pump Cylinder Gasket
Pump Cylinder Gasket
Plunger O-Ring
Plunger O-Ring
Check Valve
Check Valve
TANK
MODELS
2301, 2301F
2302,2302F
2303, 2303F
1996
MODELS
1401,1402
1402HD, 1403
2401, 2402,
9001, 1215
FLOW CONTROL
Flow control assembly: 1913, 1914
Flow control assembly: 942-145
MODELS
1001,1101
1002, 1102
1003, 1102D
1025HD
DESCRIPTION
2302F
1001, 2301,1002,
2302,1003, 2303
1996
1401, 1401HD,
1402, 1403,2401,
2402,9001,7015
1101
1102
1102D
1025HD
1125D
Pump Assembly
942-802
942-802
942-110
942-110
942-812
942-103
Soft Goods Kit
(replacement seals,
gaskets, o-rings, etc.)
1910RG
1910RG
1910RG
1910RG
1910F S
1910F S
Flow control, hose,
extension assembly
942-145
1913
1914
1913
1913P B
1913P B
Strap (not supplied on
1 and 2 gallon units)
955-020
955-020
955-020
955-020
955-020
955-020
Pressure Relief Valve
(only on some models)
952-562
952-562
n/a
n/a
952-562
925-562
Siphon Tube
956-392
956-392
956-392
956-392
956-392
956-392
Nozzle Cap Kit
942-111
942-111
942-111
942-111
942-111
942-111
LIMITED WARRANTY
Root-Lowell Manufacturing Co. warrants to the original purchaser only that this product will continue to function as intended if
used in accordance with operating instructions (under NORMAL CONSUMER USE) for the time period as specified for model
numbers listed below: If the product fails to function as intended—DO NOT RETURN IT TO THE STORE—call our CONSUMER SERVICE HOTLINE AT 1-800-253-4642 (toll free) for fast service. We will, at our option, repair or replace any nonfunctioning parts without charge (shipping and handling charges will apply.) Root-Lowell Manufacturing Co. shall have the
option of requiring the return of the non-functioning product to the address listed below together with the proof of purchase to
establish a claim under this warranty. This warranty does not apply to damage resulting from accident, misuse, neglect,
alterations, operation not in accordance with instructions, commercial use, or normal wear of o-rings or seals.
Model Number
Warranty Period
1401HD, 7015, 9001, 1215
1 Year Limited
1101, 1102, 1102D, 1401, 1402, 1403
3 Year Limited
2301, 2302, 2303, 1001, 1002, 1003, 1996,1125D,
2401, 2402, 1025HD
5 Year Limited
ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR CONSUMER USE, ARE LIMITED TO THE DURATION SPECIFIED ABOVE. ROOT-LOWELL MANUFACTURING CO.’S LIABILITY
IS LIMITED SOLELY TO THE REPAIR OR REPLACEMENT OF THE NON-FUNCTIONING PRODUCT OR PART. ROOTLOWELL MANUFACTURING CO. EXCLUDES LIABILITY UNDER THIS WARRANTY FOR ANY AND ALL INCIDENTAL AND
CONSEQUENTIAL LOSS OR DAMAGE.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or
consequential damages, so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights
and you may have other rights which vary from state to state.
IF YOU HAVE QUESTIONS OR CONCERNS, PLEASE CALL OUR CONSUMER SERVICE HOTLINE AT 1-800-253-4642
(Mon. through Fri., 8:00 a.m. to 7:00 p.m. EST) or WRITE: ROOT-LOWELL MANUFACTURING CO. • ATTN: CONSUMER SERVICE •
1000 FOREMAN ROAD • P. O. BOX 289 • LOWELL, MICHIGAN 49331-0289.
HELP PROTECT THE ENVIRONMENT. PLEASE USE CHEMICALS CAREFULLY, ACCORDING TO CHEMICAL
MANUFACTURER’S GUIDELINES, AND ALWAYS DISPOSE OF THEM PROPERLY.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising