Addendum Instr.indd

Addendum Instr.indd
ENGLISH
2.1 Check Brake Lines at hub
1. Remove Steering Limiter Bolt
During shipping, the Brake Arm may engage and push the Cable Housing out of
its Barrel Adjustor. End of Cable Housing must insert fully into its Barrel Adjustor to
function properly.
20 mm or equivalent wrench required.
1. Steering Limiter Bolt is located behild the left rear ChildPod® wheel. Remove by
turning counterclockwise with wrench.
2.1.1 ChildPod® Rear Wheels may not install due to Brake Arm engagement
during shipment
Incorrect
2. Press Plastic Plug (included in package) into hole.
Cable Housing
Brake Arm engaged
Barrel Adjustor
Correct
Steering Limiter Bolt
2. Troubleshooting LeaderLink® Braking
Cable Housing
NOTE
Brake Arm disengaged
Barrel Adjustor
Section 9.7.1: Adjust Brake Hub Barrel Adjustor in the Zigo® Leader™
Owner’s Manual is incorrect. The Brake Lines are reversed.
2.2 Adjusting Barrel Adjustors
2.2.1 ChildPod® Rear Wheels may not install due to excess Brake Arm tension
If the ChildPod® Rear Wheel does not install due to excess Brake Arm tension, Barrel
Adjustors should be moved inward to bring the Brake Arm in.
Jogging/Parking Brake
Barrel Adjustor
LeaderLink® Barrel Adjustor
Barrel Adjustor Locking Nut
Barrel Adjustor
© 2009 SOMA Cycle, Inc. All Rights Reserved.
71 So. Orange Ave., Ste. 396, So. Orange, NJ, 07079, USA : www.myzigo.com : (973)378-8788
05/2009
1080-03-0100
ENGLISH
ADDITIONAL INSTRUCTIONS
ENGLISH
3. Setting up the Cycle - Additional Items
2. Move top and bottom Barrel Adjustors inward by turning clockwise. Turn both
Barrel Adjustors evenly and test for Rear Wheel fit every 2 or 3 turns.
3.1 Install the Front Cantilever Brake Cable Yoke
3. After installing Rear Wheel, turn Barrel Adjustor Locking Nut clockwise to lock Barrel
Adjustor in place.
ENGLISH
1. Release top and bottom Barrel Adjustor Locking Nuts to allow for Barrel Adjustor
movement. Turn counterclockwise.
3.2 Setting up the Front Cantilever Brake
3.3 Installing the LeaderLink® Post
1. Remove all packaging materials from Cycle.
2.2.2 Front Brake Lever (left lever on Cycle) and Brake Arm may not spring back
to unengaged position
2. Insert LeaderLink® Post into Cycle head tube located in center of Stem Clamp.
This occurs when there is slack in any of the Brake Lines. Excess slack is most likely
to occur on ChildPod® between base of LeaderLink® Post (located near Steering
Interface) and hub.
LeaderLink® Post
1. Uncouple Cycle from ChildPod®. Pull back Brake Arms to ensure that they have
each returned to the unengaged position.
Stem
2. Turn ChildPod® on its side. Check all Brake Lines for slack in Cable Housing.
3. Once the slack Brake Line is identified:
a. Turn its Barrel Adjustor Locking Nut counterclockwise to allow for Barrel Adjustor
movement.
b. Remove Brake Line slack by turning Barrel Adjustor of slack Cable Line
counterclockwise. Do not overtighten Barrel Adjustor. See Section 2.2.1 if you
overtighten.
3.4 Installing Reflectors
CAUTION
c. Lock Barrel Adjustor Locking Nut by turning clockwise.
d. Couple Cycle to ChildPod® and check Front Brake lever action.
Always make sure to use the reflectors in their correctly mounted
orientation for best safety and visibility.
4. Restraint Harness
Brake Arm disengaged
Ensure that Lap Belts are properly configured for either one or two children. See
Section 8.1 in the Zigo Leader Owner’s Manual.
Barrel Adjustor Locking Nut
Barrel Adjustor
© 2009 SOMA Cycle, Inc. All Rights Reserved.
71 So. Orange Ave., Ste. 396, So. Orange, NJ, 07079, USA : www.myzigo.com : (973)378-8788
05/2009
1080-03-0100
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising