Hyundai Elantra 2017-up 95-7376B

Hyundai Elantra 2017-up 95-7376B
INSTALLATION INSTRUCTIONS FOR PART 95-7376B
Hyundai Elantra 2017-up
95-7376B
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets
REV. 9/27/2016 INST95-7376B
Dash Disassembly.................................................. 2
Kit Preparation........................................................ 3
Kit Assembly
–. ISO DDIN radio provision....................................... 3
KIT FEATURES
• ISO DDIN radio provision
• Painted matte black
A
Table of Contents
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
B
CAUTION! All accessories, switches, climate controls panels,
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: 70-7304 (without 7-inch display radio) • 70-7306 (with 7-inch display radio)
Antenna Adapter: N/A (without 7-inch display radio) • 40-KI11 (with 7-inch display radio)
METRA – The World’s best kits.®
metraonline.com
and especially air bag indicator lights must be connected before
cycling the ignition. Also, do not remove the factory radio with
the key in the on position, or while the vehicle is running.
© COPYRIGHT 2016 METRA ELECTRONICS CORPORATION
95-7376B
Dash Disassembly
1. Open the passenger front door,
then unclip and remove the trim
panel from the side of dashboard.
Remove the (1) Phillips screw
securing the silver trim panel.
2. Unclip and remove the silver
trim panel that runs along the
dashboard from under the radio,
and above the glovebox.
3. Open the driver’s door, then unclip
and remove the trim panel from
the side of the dashboard. Remove
the (1) Phillips screw securing the
silver trim panel.
5. Unclip the trim panel above the
steering column, and then unclip
and remove the entire panel
surrounding the instrument cluster.
Note, these two panels are one
assembly.
Please visit Metraonline.com for
dash disassembly illustrations.
6. Remove the (2) Phillips screws
securing the radio trim panel, then
unclip and remove the panel.
7. Remove the (4) Phillips screws
securing the radio and then
remove.
Continue to Kit Assembly
4. Unclip and remove the silver trim
panel from under the driver’s side
A/C vent.
2
95-7376B
Kit Preparation
Kit Assembly
ISO DDIN radio provision
1. Remove the (3) Phillips screws
securing the A/C vents to the radio
trim panel and then remove.
2. Secure the vents onto the radio
trim panel using the factory
hardware.
3. Attach the radio brackets to the
radio using the screws supplied
with the radio. (Figure A)
Please visit Metraonline.com for
kit preparation illustrations.
4. Locate the factory wiring harness
and antenna connector in the
dash and complete all necessary
connections to the radio. Metra
recommends using the proper
mating adapter from Metra and/or
AXXESS. Test the radio for proper
operation.
5. Secure the assembly into the dash
opening using the factory hardware.
6. Snap the radio trim panel over
the radio assembly, and then
reassemble the dash in reverse
order of disassembly.
3
(Figure A)
INSTALLATION INSTRUCTIONS FOR PART 95-7376B
IMPORTANT
If you are having difficulties with the installation
of this product, please call our Tech Support line
at 1-800-253-TECH. Before doing so, look over
the instructions a second time, and make sure
the installation was performed exactly as the
instructions are stated. Please have the vehicle
apart and ready to perform troubleshooting
steps before calling.
KNOWLEDGE IS POWER
REV. 9/27/2016 INST95-7376B
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
METRA – The World’s best kits.®
metraonline.com
© COPYRIGHT 2016 METRA ELECTRONICS CORPORATION
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising