LiftMaster, 892LT, 894LT, remote controls, transmitter, programming

LiftMaster, 892LT, 894LT, remote controls, transmitter, programming
2-BUTTON AND 4-BUTTON REMOTE CONTROLS
MODELS 892LT AND 894LT
The 892LT/894LT remote control is compatible with Security✚ 2.0™ garage door openers, gate operators,
commercial door operators and commercial receivers. The remote control can also be programmed to
Security✚ 2.0™ products with encrypted DIP switches. The remote control can also be used as a
replacement for LiftMaster® remote control models 972LM/974LM and 372LM/374LM.
After following the correct programming steps, the 892LT and 894LT remote control will work with
garage door openers or receivers which use the following accessories:
• 890 Series (Security✚ 2.0™)
• 370 Series (Security✚ 315 Mhz)
• 970 Series (Security✚ 390 Mhz)
MODEL 892LT
To prevent possible SERIOUS INJURY or DEATH from a
moving gate or garage door:
• ALWAYS keep remote controls out of reach of children.
NEVER permit children to operate or play with remote
controls.
• Activate gate or door ONLY when it can be seen clearly,
is properly adjusted and there are no obstructions to
door travel.
• ALWAYS keep gate or garage door in sight until
completely closed. NEVER permit anyone to cross path
of moving gate or door.
MODEL 894LT
The 892LT and 894LT can clone the following DIP switch remote controls:
• 61LM (390 Mhz)
• 361LM (315 Mhz)
• 811LM (Security✚ 2.0™)
PROGRAMMING
There are two different programming options depending on your application. If you are programming the remote control to an existing DIP switch remote control, refer to OPTION B. For all other
programming, refer to OPTION A.
A
OPTION A
The instructions are written for garage door openers, however the
steps still apply for compatible products. Make sure the garage door
opener has a working light bulb because it is a programming
indicator. The illustrations are generic, so your garage door opener
may look different.
1
2
Locate the Learn button on the garage door opener (Figure 1).
3
To enter programming mode, press the Program button until
the LED on the remote control turns on.
4
Press and release the Learn button on the garage door opener.
The Learn LED will light. Within 30 seconds...
5
Remove the battery cover from the new remote control and
locate the Program button (Figure 2).
Press and release the remote control button that you want to
use...
Check to see if the garage door opener light bulb blinks.
If not, wait for the remote control LED to light solid then slowly
press and release the remote control button again. Repeat until
the light bulb blinks. DO NOT press the button after the light
bulb blinks.
6
To exit programming mode, press and release the Program
button on the remote control. The LED on the remote control
will turn off.
7
To test, press and release the programmed button on the
remote control. The garage door opener will activate.
B
FIGURE 1
Learn
LED
Learn
Button
OR Learn
LED
Learn
Button
OR
Learn
LED
Learn
Button
Program
Button
LED
OPTION B
1
Make sure the existing dip-switch remote control and the
new remote control are in close proximity to each other.
2
Remove the battery cover from the new remote control and
locate the Program button (Figure 2).
3
To enter programming mode on the new remote control,
press the program button until the LED on the remote
control turns on.
4
Press and hold the button that currently activates your
product on the existing remote control that you want to
copy to the new remote control. The LED on the new remote
control will flash.
5
Press and release the button on the new remote control that
you want to program. The LED on the new remote control
will flash rapidly, then return to a flash slowly. DO NOT
press the button after the LED flashes.
6
To exit programming mode, press and release the Program
button on the remote control. The LED on the remote
control will turn off.
7
To test, press and release the programmed button on the
remote control. The gate operator or commercial door
operator will activate.
FIGURE 2
For more information
visit www.devancocanada.com
HOW TO USE THE REMOTE CONTROL
Press and hold the button down until the door or gate starts to
move. The remote control will operate from up to 3 car lengths
away on typical installations. Installations and conditions vary,
contact an installing dealer for more information.
BATTERY
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
To reduce risk of fire, explosion or chemical burn:
• DO NOT recharge, disassemble, heat above 212° F (100° C)
or incinerate.
WARRANTY
ONE YEAR LIMITED WARRANTY
The Chamberlain Group, Inc. warrants to the first consumer
purchaser of this product that is free from defect in materials
and/or workmanship for a period of 1 year from the date of
purchase.
REPLACEMENT PARTS
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or
modifications of this receiver and/or transmitter are prohibited, except for changing the
code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE
PARTS.
Tested to Comply with FCC Standards for Home or office use. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Visor Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29B137
The LED(s) on your remote control will stop flashing when the
battery is low and needs to be replaced. To replace battery, open
the cover as shown. Insert battery. Replace the battery with AAA
batteries. Dispose of old battery properly.
HOW TO ORDER
REPAIR PARTS
Additional buttons on the remote control can be programmed to
operate up to 3 devices such as additional garage door openers,
light controls, gate operators or access control systems.
DEVANCO CANADA
19192 HAY ROAD, UNIT Q
SUMMERSTOWN, ON K0C 2E0
TOLL FREE: 855-931-3334
www.devancocanada.com
WHEN ORDERING REPAIR PARTS
PLEASE SUPPLY THE
FOLLOWING INFORMATION:
3 PART NUMBER
3 DESCRIPTION
3 MODEL NUMBER
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising