User Guide - Webcollage.net

User Guide - Webcollage.net
81L21 SERIES
USER GUIDE
HARD FLOOR EXPERT
™
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING YOUR VACUUM.
Always connect to a polarized outlet (one slot is wider than the other) for charging. Unplug from outlet when not in use and before conducting
maintenance. When using an electrical appliance, basic precautions should be observed, including the following:
WARNING
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, OR INJURY:
»Do not use outdoors or on
wet surfaces.
»Do not allow to be used as a toy.
»Close attention is necessary
when used by or near children.
»Do not use for any purpose
other than described in this
User’s Guide.
»Use only manufacturer’s
recommended attachments.
»Do not use with damaged cord
or plug.
»If appliance is not working as
it should, has been dropped,
damaged, left outdoors, or
dropped into water, have it
repaired at an authorized
service center.
»Do not pull or carry by cord, use
cord as a handle, close a door on
cord, or pull cord around sharp
edges or corners. Do not run
appliance over cord. Keep cord
away from heated surfaces.
»Do not unplug by pulling on cord.
To unplug, grasp the plug, not
the cord.
»Do not handle charging base,
including plug and charging base
terminal with wet hands.
»Do not charge the unit outdoors.
»Use only the charger supplied by
the manufacturer to recharge.
»Do not incinerate the appliance
even if it severely damaged. The
batteries can explode in a fire.
»Do not put any object into
opening.
»Do not use with any opening
blocked.
»Keep openings free of dust, lint,
hair and anything that may
reduce airflow.
»Keep hair, loose clothing, fingers,
and all parts of body away from
openings and moving parts.
»Use extra care when cleaning
stairs.
»Do not pick up flammable
materials (lighter fluid, gasoline,
kerosene, etc.) or use in the presence of explosive liquids
or vapors.
»Always turn off this appliance
before connecting or
disconnecting the motorized
nozzle.
»Do not pick up toxic material
(chlorine bleach, ammonia,
drain cleaner, etc.).
»Do not use vacuum cleaner in an
enclosed space filled with vapors
given off by oil base paint, paint
thinner, some moth proofing
substances, flammable dust, or
other explosive or toxic vapors.
»Do not pick up hard or sharp
objects such as glass, nails,
screws, coins, etc.
»Do not pick up anything that
is burning or smoking, such as
cigarettes, matches, or hot ashes.
»Do not use without dust cup or
filters in place.
»Use only on dry, indoor surfaces.
»Keep appliance on a level surface.
SAVE THESE INSTRUCTIONS
FOR FUTURE USE
This model is for household use only.
Always connect the charging base to a polarized outlet (one slot is wider than the other). Do not modify the polarized plug to fit a non-polarized outlet or extension cord.
THIS APPLIANCE HAS A
POLARIZED
PLUG
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install a proper outlet. Do not change the plug in any way.
2
www.BISSELL.com
Thanks for buying a BISSELL vacuum
We’re glad you purchased a BISSELL
vacuum. Everything we know about
floor care went into the design and
construction of this complete,
high-tech home cleaning system.
Your BISSELL vacuum is well made,
and we back it with a limited
one-year warranty. We also stand
behind it with a knowledgeable,
dedicated Consumer Care
department, so, should you ever
have a problem, you’ll receive fast,
considerate assistance.
My great-grandfather invented the
floor sweeper in 1876. Today, BISSELL
is a global leader in the design,
manufacture, and service of high
quality homecare products like your
BISSELL vacuum.
Safety Instructions . . . . . . . . . . 2
Product View . . . . . . . . . . . . . . . 4
Assembly . . . . . . . . . . . . . . . . . . . 5
Operations . . . . . . . . . . . . . . . . . . 5
Maintenance & Care . . . . . . . 6-8
Troubleshooting . . . . . . . . . . . . 9
Replacement Parts . . . . . . . . . 10
Warranty . . . . . . . . . . . . . . . . . . . 11
Service . . . . . . . . . . . . . . . . . . . . . 11
Consumer Care . . . . . . . . . . . . . 12
Product Registration . . . . . . . . 12
Thanks again, from all of us
at BISSELL.
Mark J. Bissell
Chairman & CEO
www.BISSELL.com
3
Product View
1
1Handle Grip
2 Upper Handle
3 Power Switch
4 Upper Tank
5 Separator Grill
6 Dirt Container
7 Dirt Cup Release
8Filter
9Edge Cleaning
Path
10 Swivel Head
11 Large Suction Paths
12 Cord Clip
13 Carry Handle
14Quick Release Cord Wrap
15 Long Power Cord
16 Foot Release Latch
2
3
4
5
12
13
14
15
6
7
8
10
9
16
11
WARNING
Plastic film can be dangerous. To avoid
danger of suffocation, keep away from
babies and children.
4
www.BISSELL.com
WARNING
Do not plug in your vacuum cleaner until
you are familiar with all instructions and
operating procedures.
WARNING
To reduce the risk of electric shock, turn
power switch off and disconnect polarized
plug from electrical outlet before performing
maintenance or troubleshooting checks.
Assembly
WARNING
Do not plug in your vacuum cleaner until
you are familiar with all instructions and
operating procedures.
The Hard Floor Expert is shipped in three pieces:
Upper handle, Body, Foot
No tools are required for assembly.
1. Slide upper handle into body and push in
firmly until handle locks into place.
1.
2.
2. Slide foot onto body of unit until foot
locks into place.
3. Wrap power cord on back of unit.
3.
Operations
Transporting unit
Place unit in upright position and tip back
to roll on rear wheels.
Power switch
The power switch is located on the top of the
body of unit.
Power
Switch
Push switch ON (l) to vacuum and OFF (O)
when cleaning is complete.
1. Turn quick release cord wrap to remove
power cord; plug into electrical outlet.
2 Lightly press the foot of the vacuum and
pull handle back to detent.
3. Turn power switch to ON (I) position
1.
2.
4. Clean your hard floors, under cabinets, and
easily maneuver around furniture. To clean
along edges, align the end suction points
along the areas you want to clean.
5. When finished cleaning, turn power switch
to OFF (O) position.
6. To store the unit, return handle to upright
position.
4.
www.BISSELL.com
5
Maintenance & Care
To maintain maximum cleaning performance, the
following maintenance steps must be performed:
Emptying the dirt container
Dirt container should be emptied before
debris reaches the FULL line.
WARNING
To reduce the risk of electric shock, turn power switch off
and disconnect polarized plug from electrical outlet before
performing maintenance or troubleshooting checks.
1. Turn power OFF (O). Unplug unit from
electrical outlet.
2. Grasp the two release buttons on the front
of the dirt container, depress both at same
time and pull container straight out to remove
from vacuum.
Full Line
3. Empty dirt into garbage can.
NOTE: The dirt container may be washed in
warm water with mild detergent. Make sure it
is completely dry before replacing. DO NOT
PUT IN DISHWASHER.
2.
4. Replace dirt container back in vacuum until
it snaps firmly into place.
NOTE: To ensure full suction power, make sure
dirt container is thoroughly positioned and
locked into place.
4.
Cleaning the separator grill
1. Unplug unit from electrical outlet.
2. Separator grill can be reached by
removing the dirt container, reaching into
upper tank and turning rim of separator grill
counter-clockwise to unlock.
. Pull straight
down to remove.
3. Separator grill may be wiped clean with a
damp cloth. Air-dry thoroughly before replacing.
4. Replace separator grill by inserting into upper
tank and turning clockwise until it is secured in
place
.
6
www.BISSELL.com
2.
4.
Maintenance & Care
WARNING
Cleaning or replacing the filters
Use only genuine BISSELL model number
54A2 replacement filters in your BISSELL
vacuum. To purchase visit: WWW.BISSELL.COM
or call 1-800-237-7691.
1. Turn power OFF (O). Unplug unit from
electrical outlet.
2. Remove the dirt container as previously
directed on page 6 and set aside.
To reduce the risk of electric shock, turn power switch off
and disconnect polarized plug from electrical outlet before
performing maintenance or troubleshooting checks.
3.
3. Grasp the filter cup and lift up and out.
4. Rotate top of filter cup to the
position and remove.
unlock
5. Remove filter assembly from cup. Separate
the foam filter from the inner pleated filter.
6. Foam filter may be washed in warm water.
Mild detergent may be used if desired. Rinse
well and let air dry thoroughly before replacing.
5.
7. Pleated filter should be tapped firmly against
the inside of a trash can, removing any visible
dirt. Do not wash the pleated filter.
8. Before replacing filters back into unit, be
sure they are dry and nested back together.
8.
9.
9. Place filters back into filter cup, replace
cover and twist to lock position, making sure
the dots are aligned.
Replace filter cup back into machine, insert
dirt container and snap firmly into place.
WARNING
Never operate without the filter in place.
Doing so may damage the motor and void
the warranty.
www.BISSELL.com
7
Maintenance & Care
Clearing clogs
Low suction or poor pickup may be due to a
clog in the dirt container. If this occurs, follow
these steps to check for and clear clog.
1. Turn power OFF (O). Unplug unit from
electrical outlet.
2. Remove and empty dirt container as
previously directed on page 6. While dirt
container is out check upper tank for build
up of clogs.
3. Remove separator grill as instructed on
page 6 and check suction inlet for clog.
4. Check foot for clog in air path.
Brush and wiper maintenance
Regularly check rear angle brush and front
wipers on the underside of the unit and
wipe any debris that has accumulated with
a damp cloth.
Thermal motor protection
An internal thermal protector has been designed
into your cleaner to protect it from overheating.
When the thermal protector activates, the main
vacuum motor will stop operating. If this
happens, proceed as follows.
1. Turn the cleaner OFF and unplug from
electrical outlet.
2. Check the cleaner for the source of
overheating problem (i.e. full dirt cup, dirty
filters or clog).
3. Fix the problem by following the steps in
the maintenance section of the user guide.
4. When the motor cools for approximately 30
minutes, the thermal protector automatically
resets and cleaning may continue. If the cleaner
will not turn on or the thermal protector
continues to activate, your cleaner may need
servicing. Call BISSELL Consumer Services or
visit the website.
8
www.BISSELL.com
WARNING
To reduce the risk of electric shock, turn power switch off
and disconnect polarized plug from electrical outlet before
performing maintenance or troubleshooting checks.
Troubleshooting
WARNING
To reduce the risk of electric shock, turn power switch off
and disconnect polarized plug from electrical outlet before
performing maintenance or troubleshooting checks.
Problem
Possible causes
Remedies
Vacuum
cleaner won’t
turn on
Power cord not plugged in
Check electrical plug
Blown fuse/tripped breaker
Check/replace fuse or reset breaker
Dirt container is full
Empty dirt container
Dirt container is not installed
properly
Position container correctly and
snap firmly into place
Separator grill is not installed
properly
Position separator grill in upper tank
and twist firmly into place
Clog in vacuum
Follow instructions on page 8 to
clear clog
Separator grill is clogged with
debris
Remove and wipe separator grill
of all debris
Foot is loose
Make sure foot is fully inserted into
body of unit
Filters need replacing
Visit www.bissell.com or call 1-800237-7691 to order replacement filters.
Dirt container is full of debris
Empty dirt container
Filter is missing or installed
incorrectly
Check filter for correct installation
Dirt container installed incorrectly
Position container correctly and
snap firmly into place
Separator grill is missing or
installed incorrectly
Position separator grill in upper tank
and twist firmly into place
Vacuum
cleaner
has low
suction
Visible dirt
escaping from
vacuum
Please do
not return
this product
to the store.
Other maintenance or service not included in the manual should be
performed by an authorized service representative.
Thank you for selecting a BISSELL product.
For any questions or concerns, BISSELL is happy to
be of service. Contact us directly at 1-800-237-7691.
www.BISSELL.com
9
Replacement Parts
These items are available for your BISSELL Hard Floor Expert vacuum.
Call 1-800-237-7691 or visit www.bissell.com
10
PART #
PART NAME
PART #
PART NAME
1604667
Handle assembly
1604668
Dirt container
1604670
Separator grill
54A2
Pleated filter/Foam filter
assembly
203-1215
Pre-motor mesh filter
203-0250
Filter cup assembly
1604669
Cord wrap
www.BISSELL.com
Warranty
Service
Limited One-Year Warranty
Visit BISSELL.com or contact BISSELL Consumer Care to locate a
BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you
have questions about your warranty, contact BISSELL Consumer Care.
This warranty gives you specific legal rights, and you may also
have other rights which may vary from state to state. If you need
additional instruction regarding this warranty or have questions
regarding what it may cover, please contact BISSELL Consumer Care
by E-mail, telephone, or regular mail as described below.
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon
receipt of the product BISSELL will repair or replace (with new or
remanufactured components or products), at BISSELL’s option, free of
charge from the date of purchase by the original purchaser, for one
year any defective or malfunctioning part.
See information below on "If your BISSELL product should require
service".
This warranty applies to product used for personal, and not
commercial or rental service. This warranty does not apply to fans
or routine maintenance components such as filters, belts, or brushes.
Damage or malfunction caused by negligence, abuse, neglect,
unauthorized repair, or any other use not in accordance with the
User's Guide is not covered.
BISSELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S
LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
If your BISSELL product should
require service:
Website:
www.BISSELL.com
Or Call:
BISSELL Consumer Care
1-800-237-7691
Monday – Friday 8am - 10pm ET
Saturday 9am - 8pm ET
Sunday 10am - 7pm ET
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM
THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER
WARRANTIES EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES
WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED TO THE ONE YEAR DURATION FROM THE DATE
OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied
warranty last so the above limitation may not apply to you.
NOTE: Please keep your original sales
receipt. It provides proof of date of
purchase in the event of a warranty claim.
www.BISSELL.com
11
Register your product today!
Registering is quick, easy and offers you benefits over the lifetime of your product.
You’ll receive:
BISSELL Rewards Points
Automatically earn points for
discounts and free shipping on
future purchases.
Faster Service
Supplying your information now
saves you time should you need
to contact us with questions
regarding your product.
Product Support
Reminders and Alerts
We’ll contact you with any
important product maintenance
reminders and alerts.
Special Promotions
Optional: Register your email
to receive notice of offers,
contests, cleaning tips and more!
Visit www.BISSELL.com/registration now!
BISSELL Consumer Care
For information about repairs or replacement parts, or questions about your warranty:
Call:
Email:
BISSELL Consumer Care
www.BISSELL.com
1-800-237-7691
Monday - Friday
Saturday
Sunday
8 am - 10 pm ET
9 am - 8 pm ET
10am - 7pm ET
Visit the BISSELL website: www.BISSELL.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It provides proof of purchase
date in the event of a warranty claim. See Warranty on page 11 for details.
©2014 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 160-4056 Rev 05/14
Visit our website at: www.BISSELL.com
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising