Mytee-Lite-man_0516_web - Kleen

Mytee-Lite-man_0516_web - Kleen
Instructions for
D
8070 Mytee Lite™
Please read before use.
Register your product
at http://www.mytee.com/
support/register
C
B
Model #
General information p. 2
Set up p. 5
Parts & pricing p. 9
Wiring diagram p. 11
Notes p.12
Serial #
Form # ADP-8070
05-16
NAME
DRAWN
M.LaBarbera
DATE
mytee
13655 Stowe Dr., Poway, CA 92064
PRODUCTS,
1/2014
1
858-679-1191
INC.
GENERAL INFORMATION
Dear Customer:
Unpacking the Machine
Keep in mind that the 8070 Mytee Lite™ is a machine, so neglect or abuse
will cause unnecessary damage and void the warranty. However with simple
maintenance the 8070 will give quality performance for many years to come.
Caution and Warnings
When the machine is delivered, carefully inspect the shipping carton and the
machine for damage. If damage is evident, save the shipping carton so that it can
be inspected by the carrier that delivered it. Contact the carrier immediately to file a
freight damage claim.
Congratulations on the purchase of your new 8070 Mytee Lite™. As you are
already aware, the scene of the equipment world is becoming more high tech, and
we at Mytee Products Inc. strive to keep you on the cutting edge with superior
quality and technology.
Symbols
Mytee uses the symbols below to signal potentially dangerous conditions. Always
read this information carefully and take the necessary steps to protect personnel
and property.
If warranty questions arise, please consult your user manual or get in touch with
your distributor. If you have questions about maintenance, replacing parts or
ordering parts, please call an authorized Mytee Products Inc. Service Center.
To see an updated list, visit our website at www.mytee.com
Is used to warn of immediate hazards that will cause severe personal injury or death.
Before you begin cleaning, please read your manual thoroughly.
Sincerely,
Mytee Customer Care Dept.
Is used to call attention to a situation that could cause severe personal injury.
Grounding Instructions
This machine must be grounded. If it should malfunction or breakdown, grounding
provides a path of least resistance for electrical shock. This machine is equipped with
a cord having an equipment-grounding conductor and grounding plug. The plug must
be plugged into an appropriate outlet that is properly installed in accordance with all
local code and ordinances. Do not remove ground pin; if missing, replace plug before
use.
Is used to call attention to a situation that could cause minor personal injury or
damage to the machine or other property. When using an electrical appliance, basic
precautions should always be followed, including the following: Read all instructions
before using this machine. This product is intended for commercial use only.
To reduce the risk of fire, electrical shock, or injury:
1. Read all instructions before using equipment.
2. Use only as described in this manual. Use only manufacturer’s recommended
attachments.
3. Always unplug power cord from electrical outlet before attempting any adjustments
or repairs.
4. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
5. Do not pull or carry by cord. Do not close a door on cord or pull cord around sharp
edges or corners.
6. Do not run appliance over cord. Keep cord away from heated surfaces.
7. Do not use with damaged cord or plug. If cord is damaged, repair immediately.
8. Do not use outdoors or on wet surfaces and or standing water.
9. Always unplug or disconnect the appliance from power supply when not in use.
10. Do not allow to be used as a toy. Close attention is necessary when used by or
near children.
11. Do not use in areas where flammable or combustible material may be present.
12. Do not leave the unit exposed to harsh weather elements. Temperatures below
freezing may damage components and void warranty.
13. Use only the appropriate handles to move and lift unit. Do not use any other parts
of this machine for this purpose.
14. Keep hair, loose clothing, fingers, and all parts of the body away from all
openings and moving parts.
15. Use extra care when cleaning on stairs.
16. To reduce the risk of fire or electric shock, do not use this machine with a solidstate speed control device.
17. The voltage and frequency indicated on the name plate must correspond to the
wall receptacle supply voltage.
18. When cleaning and servicing the machine, local or national regulations may apply
to the safe disposal of liquids which may contain: chemicals, grease, oil, acid, alkalines, or other dangerous liquids.
19. Do not leave operating unattended.
Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or service person if you are in doubt
as to whether the outlet is properly grounded. Do not modify the plug provided with
the machine. If it will not fit the outlet, have a proper outlet installed by a qualified
electrician.
This appliance is for use on a nominal 120-volt circuit, and has a grounding plug
that looks like the plug illustrated in Figure 1 below. A temporary adapter illustrated
in Figures 2 and 3 may be used~to connect this plug to a 2-pole receptacle as
shown in Figure 2 if a properly grounded outlet is not available. The temporary
adapter should be used only until a properly grounded outlet (Figure 1) can be
installed by a qualified electrician. The green colored rigid ear, tab or the like
extending from the adapter must be connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the adapter is used, it must be held
in place by a metal screw. Grounding adapters are not approved for use in Canada.
Replace the plug if the grounding pin is damaged or broken.
The Green (or GreenYellow) wire in the cord is the grounding wire. When replacing
a plug, this wire must be attached to the grounding pin only.
DO NOT use extension cords.
Please Note for America use only
Grounded Outlet
Adapter
Metal
Screw
Grounding Pin
Grounded Outlet Box
Figure 1
Parts and Service
Figure 2
Filling the Solution Tank
Tab for Grounding
Screw
1. Fill the solution tank with the approved cleaning solution.
2. Do not fill up the solution tank completely: 1” should be left free at the top.
3. Typically, the solution should be a mixture of water and a cleaning chemical
appropriate for the type of job.
4. Always follow the dilution instructions on the chemical container label.
5. The temperature of the cleaning solution must not exceed 70oC/160oF.
Figure 3
Repairs, when required, should be performed by Mytee service personnel or Mytee
authorized Service Center using Mytee original replacement parts and accessories.
Call Mytee for repair parts or service. Please specify the Model and Serial Number
when discussing your machine.
Name Plate
Use only non-flammable liquid in this machine.
The Model and Serial Number of your machine are shown on the Nameplate on the
back panel of the machine. This information is needed when ordering repair parts
for the machine. Use the space provided on the front cover to note the Model and
Serial Number of your machine for future reference.
2
GENERAL INFORMATION
Setup
Maintenance Schedule
1. Fill solution tank with water or approved cleaning agent. For best results, fill with
warm water (140o). Replace vacuum tank.
Flammable materials can cause an explosion or fire. Do not use flammable solutions
or materials in tank(s).
FOR SAFETY: When using machine, follow mixing and handling instructions on
chemical containers.
ATTENTION: If using powdered cleaning chemicals, mix prior to adding.
Maintenance item
Daily
Clean and inspect Tanks
Clean and inspect Hoses
Check power supply cable
Clean machine with all purpose cleaner and cloth
Check spray nozzles
Flush solution system with Mytee system maintainer
Remove and clean float shut-off screen from tank
Inspect vacuum hoses for holes and loose cuffs
Inspect machine for water leaks and loose hardware
x
x
x
x
Once a week
x
x
x
x
x
Trouble Shooting
2. Attach solution hose (located front of machine). NOTE: Make sure the quick
disconnect snap together firmly. As you do this, always inspect hoses for cracks or
fraying. Do not use if hoses are damaged.
3. Attach other end of solution hose to cleaning tool.
4. Attach vacuum hose to recovery tank.
5. Plug machine’s cord into a grounded wall outlet. FOR SAFETY: Do not operate
machine unless cord is properly grounded. FOR SAFETY: Do not operate machine
with the use of an extension cord.
6. Turn on pump. Pull trigger on tool until you have a steady flow.
7. Release tool trigger. Turn on heater.
8. Wait 5–7 minutes for unit to pre-heat.
9. Pull trigger on tool until hot water begins flowing.
10. Turn on vacuum motor.
11. Begin cleaning. Make two dry passes to every wet pass.
12. For floor cleaning, unplug tool and attach floor wand.
13. Work away from cords to avoid damage.
14. Use a defoamer in your recovery tank.
15. To clean heavily soiled areas, repeat cleaning from different directions.
16. When vacuum tank is full, empty tanks.
17. When work is complete, unplug cords and hoses.
18. Wrap and clean hoses. Clean all tanks.
There is no power.
1. Plug machine in proper outlet.
2. Check circuit breaker; reset circuit breaker, other items should not run on the
same circuit as machine. Outlet must be a 20-amp circuit.
Pump does not work properly.
1. Snap quick disconnects firmly together.
2. Check solution tank; may be empty.
3. Jets clogged, remove jet and flush clean.
4. Filters clogged, remove filters and rinse clean with water.
5. Heater is blocked; flush out with Mytee’s system maintainer.
6. If brass check valve is stuck replace valve.
7. Check pump wire. May need to reconnect wire.
8. Switch plate switch may need to be replaced.
9. If pump motor brushes are worn, replace pump.
Heater does not work properly.
1. If sensor mounted on the heater has popped, reset sensor by pushing in button.
2. Heating element may need to be replaced.
1. Vacuum carpet and upholstery and remove other debris.
2. Perform machine setup procedures.
3. Inspect power cord for damage.
Vacuum motor does not work properly.
1. Check that hose is tightly connected.
2. Close drain hose valve completely.
3. Check and clean foam filter located in recovery tank.
4. If water is coming out of vacuum motor, use a low foaming detergent.
5. Clean upholstery tool or floor wand jets.
Operation
Accessories (optional)
Pre-Operation
1. Turn pump switch on.
2. Pull up on tool lever to release air in the line. Hold lever until a steady flow of water
comes out of the wand.
3. Once pump is primed and there is pressure in the solution line, turn on heater switch
(if model is equipped with heater) and wait a few minutes for water to heat up.
4. Once water is heated, turn on vacuum and begin cleaning.
Note: When cleaning upholstery, always check manufacturer’s cleaning instructions.
3601 System Maintainer
8400DX Mytee Dry™ Upholstry Tool
8390-EZ-C Cleaning Wand
8700 Crevice Tool
FAQs
Q: How much does the 8070 weigh and what are the dimensions?
A: 43 Pounds - Dimensions are w/handle: 33” x 12 3/4” x 37”,
w/o handle: 21 1/2” x 12 3/4” x 28 1/2”.
Shipping weight is 72.5 lbs. and shipping dimensions are 31 3/4” x 17 1/4” x 41 3/4”
1. Work away from outlet and power cord to prevent cord damage.
2. Use a recommended foam control solution in the recovery tank to prevent vacuum
motor damage. Periodically check for excessive foam buildup in solution tank, and
recovery tank.
3. To clean heavily soiled areas, repeat cleaning path from different direction.
4. When vacuum tank is full, it is time to empty the dirty water from the recovery tank,
and refill solution tank.
5. After cleaning, relieve water pressure from tool before disconnecting hose.
Squeeze trigger for five seconds after turning main power switch off.
Q: What comes standard with the 8070?
A: The 8070 comes with 15’ 1-1/4” Hose-n-Hose™ Vacuum/ Internal Solution Hose
Combo (8501), a 4” Stainless Steel Upholstery Tool (8400), Cuff-Lynx™ H122, and a
drain hose (A110).
Q: Does Mytee recommend a tool for the machine?
A: A variety of tools can be used with the unit, including our 8390 wand, 8700 crevice
tool, 8400 upholstery tool, and 8400DX Mytee Dry™ upholstery tool.
After Use
Q: Where do I plug the machine in?
A: The 8070 requires a 20A grounded circuit. Please note: GFI outlets may trip
before the breaker setting.
1. Unplug.
2. Empty solution tank and rinse it with clean water.
3. Inspect hoses and replace if damaged.
4. Attach 45° drain elbow to dump valve and lift up drain valve lever to empty
recovery tank.
5 Inspect solution filter. Clean or replace if damaged.
6. Store the machine in a clean, dry place.
7. Open recovery tank cover to promote air circulation.
8. Do not expose to rain. Store indoors.
Q: What is the proper pre heat cycle for the 8070?
A: Turn pump switch to the on position and prime pump through the solution hose
and the tool. Then turn the heater switch to the on position. Let the machine sit idle
for 5-7 minutes. Spray tool until you feel the hot water from the jet.
Q: Are the pumps re-buildable for the 8070?
A: Yes, both the seals and the pistons have repair kits available.
Please see the pump manual that shipped with your machine for the
maintenance schedule.
3
GENERAL INFORMATION
Q: Is there anything I can do to increase the expected life of my machine?
A: Running the vacuum motors with the tank empty and lid off will allow excess
moisture in the vacs to dry off. You should also run a System Maintainer through
the system to keep the hoses, pump, and heater clean and free of debris.
4
a
8
7
6
4
5
3
8070 MYTEE LITE™
a
a
F
a
REV.
OD
D
a
a
FRONT
a
a
BACK
1
a
E
8
a
a
2
C
D
3
9
4
C
10
11
7
B
5
B
14
6
1. Hose hanger
2. Recovery tank lid
3. Cuff-Lynx™ vacuum hose connector
4. Open fill for solution tank
NAME connector
DATE
5. Solution hose
mytee PRODUCTS, INC.
1/2014
M.LaBarbera
DRAWN
6. Solution
tank drain
TITLE:
CHECKED
7. Solution
tank faucet fill
COMMENTS:
858-679-1191
7
8
A
7
8
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
REV
ACCESSORIES
6
QTY.
MSRP
1
$4.99 ea
1
$15.99 ea
1
$9.99 ea
2
5
4
8070
1
2
PROPRIETARY AND CONFIDENTIAL
5
6
4
5
MATERIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE FINISH
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
4
3
1
2
3
REV.
DESCRIPTION
OD
ORIGINAL DRAFT
DATE
APPROVED
JFL
SHEET 1 OF 3
DO NOT
SCALE DRAWING
3
DIMENSIONS A
TOLERANCES:
ANGULAR: MA
ONE PLACE D
TWO PLACE D
THREE PLACE D
CONNECTING THE HANDLE
E
F
SCALE: 1:24
6
UNLESS OTHER
REVISIONS
SIZE DWG. NO.
C
12
8. Basket
9. Recovery tank drain hose
10. Service latch
11. Switch plate
12. 25’ single power cord
13. 6” wheels
14. 2” casters
A
MyteeLite II
(2014)
13
1
REVISIONS
REV.
DESCRIPTION
DATE
APPROVED
OD
ORIGINAL DRAFT
9/1/2015
JFL
F
E
3
E
D
8400 - 4” Stainless Steel
Upholstery Tool
850 1 - 15’ 1-1/4”
Hose-n-Hose™ Vacuum/Solution Hose
D
C
2
C
B
B
1
In the rear of the machine, with handle/basket facing
outward, line up the four inserts on the handle with the
four inserts on the machine, located on the top sides of the
recovery tank. When installing the handle on your new
Mytee Lite™, make sure you use a hand tool (screwdriver)
for the screws and NOT a power tool. This will insure you
do not strip the hole and puncture the recovery tank.
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES
TOLERANCES:
A
H122 Cuff-Lynx™ - 2”
Female Reducer
6
5
4
A110 Drain Hose
DRAWN
NAME
DATE
M.LaBarbera
9/2015
COMMENTS:
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
8
3
mytee PRODUCTS, INC.
TITLE:
CHECKED
2
ANGULAR: MACH .5
ONE PLACE DECIMAL
TWO PLACE DECIMAL
THREE PLACE DECIMAL
858-679-1191
Drain hose w/plug,
8070
SIZE DWG. NO.
C
SCALE: 1:2
PROPRIETARY AND CONFIDENTIAL
A110
DO NOT
SCALE DRAWING
REV
OD
.03
.05
.003
DRAWN
NAME
DATE
V. LaBarbera
1/2014
CHECKED
COMMENTS:
MATERIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE FINISH
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
A
7
6
SHEET 1 OF 1
1
5
5
4
3
2
mytee PRODUCTS, INC.
TITLE:
858-679-1191
MyteeLite II (2014
SIZE DWG. NO.
REV
C 8070 (2014) E
SCALE: 1:8
DO NOT
SCALE DRAWING
1
SHEET 1 OF
8070 MYTEE LITE™
FILL SOLUTION TANK
EMPTY SOLUTION TANK
To fill the solution tank, use a bucket to pour water into
the tank’s opening located at the front of the unit. You can
also use the easy faucet fill also located at the front of the
unit. For best results, fill with warm water (140° F).
To empty any remaining water in the solution tank, remove
cap which is located at the front of the solution tank.
ATTACH HOSES
PUMP SWITCH
Attach female end of a solution hose to a wand or tool
and the male end to the Mytee Lite’s™ QD. Then connect
a vacuum hose to a wand and the male Cuff-Lynx™
hose port.
After the machine has been plugged into a 20 amp
grounded outlet, turn on pump. Pull trigger on cleaning
tool until tool releases a steady flow.
6
8070 MYTEE LITE™
VACUUM SWITCH
HEATER SWITCH
Turn on vacuum motor and begin cleaning. For best
results make two dry passes for every wet pass.
Release tool trigger. Turn on heater. Wait 5 – 7 minutes for
unit to pre-heat. Once heated, pull trigger on tool until hot
water begins flowing.
RECOVERY TANK DRAIN
VACUUM STACK FILTER
Located at the rear of the Mytee Lite™ is a bucket high
drain valve. Before extracting, screw on the included
A110 drain hose. When you’re finished extracting, unscrew the T-handle cap on the hose to drain the tank.
The Mytee Lite’s™ internal filter must be cleaned regularly and is located in the recovery tank. Twist the filter
to remove then clean and replace. If the filter is torn or
damaged, replace with a new one.
7
8070 MYTEE LITE™
SYSTEM MAINTAINER
SERVICE LATCH
Weekly flushing of the solution system with Mytee®
System Maintainer helps keep lines clean and prevents
chemical build-up, improving pump life, performance and
pressure.
To open lower housing flip-up latch that is located in the
back of the unit. Twist counter clockwise for release.
To close unit, place latch, twist clockwise and press latch
to secure.
DEFOAMER
Add defoamer in the recovery tank to reduce foam, prolonging the life of the Mytee Lite™ vacuum motor.
8
9
A
B
C
D
E
F
G021
H203
H210
H216
H213
15
16
17
18
19
B241
PH612-60
H681
H273
P585
H212
H427
H279
H042
H254
H241
H029
E515
E531
H445
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
H256
B652
AH157
C305
B170
B105
B152
PH634-13
B110
B107
46
47
48
49
50
51
52
53
54
55
56
8
H486
G068
45
H221
44
H310
H178
26
43
G004
C302P
25
P584
G022
14
24
G031
13
B119
P560
12
H379
G055
11
23
H688-A
10
22
H222
9
H201
H423
8
H846B
H350
7
21
H303
6
20
G103
5
H312
3
H230
P583
4
H135
1
2
8
PART NO.
ITEM
NO.
7
7
nipple, brass, 1/4"m, hex
adapter, brass, 1/4" sw barb x 1/4" fpt, w/gasket
sol hose, 1/4" silicone braided, clear
elbow, brass, 90 deg, 1/4" barb x 1/4" mpt
bushing, brass, 3/8"mpt x 1/4"
ferrule, 1/4" brass
pump, 120 psi, 115V
hose, 3/8" x9" (OAL), f x fsw
elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt
screw, 10-32 x 3/4" phil pan head, zinc
bumper, 7/8" x 1/4" head
latch, front
nut, lock, 1/2" steel
plate, switch, MyteeLite, 3 hole
fitting, strain relief, w/ spring, 1/2" npt
power cord, end, 25', 12/3 black
switch, rocker, 2 position
plastite screw, 10 x 1/2"
axle, 13.63" x .50" dia
washer, axle, cut 1/2" id
c-clip, 12mm, external
wheel, 6"
washer, wave, axle
flat washer, 9/16"ID x 1 1/16"OD, AN960-C916
base, MyteeLite
nut, kep, #10-32 zinc
caster, 2", black hub, gray tread
clear tubing, 1/2" OD x 3/8" ID, faucet fill
adapter, brass, 3/8" barb x 1/4"mpt
faucet fill
vac motor, 3 stage
gasket, vacuum motor
sol tank, MyteeLite
filter, strainer, 1/4"
bracket, front, small
cap, gallon jug, 1-5/8"
bolt, 1/4-20 x 1/2" hex head, zinc
washer, 1/4" lock, s/s
nut, lock, 1/4-20, nylon insert, s/s
washer, 1/4" flat, s/s
bolt, 1/4-20 x 1-1/4" hex head, s/s
screen, mesh filter, 2-3/8" dia
filter, foam, 2-3/8" x 1"
gasket, 3.25" i.d. x 5.88" o.d.
cap, 6", threaded
tether, cap, 6 1/2"
handle, MyteeLite
screw, 10-32 x 1-1/4" phil pan head, s/s
plug, 7/8", black, heyco
drain, hose plug, 1-1/2"
hose, drain, 14"
cap, 2.5" threaded, w barb
screw, 10-32 x 1/2" phil pan head, s/s
plate, connecting, MyteeLite
vac tank, MyteeLite
Cuff-Lynx, 2" m cuff x 2" mpt
DESCRIPTION
2
1
1
1
1
2
1
1
1
2
2
1
1
1
1
1
3
4
1
2
2
2
2
4
1
15
2
1
1
1
1
2
1
1
1
1
2
2
2
6
2
1
1
1
1
1
1
6
2
1
1
1
28
4
1
1
QTY.
6
6
$3.19 ea
$3.99 ea
$6.49 ft
$5.49 ea
$3.19 ea
$0.99 ea
$151.99 ea
$25.99 ea
$8.49 ea
$0.99 ea
$1.99 ea
$13.99 ea
$1.99 ea
$6.99 ea
$8.99 ea
$52.99 ea
$13.99 ea
$0.99 ea
$15.99 ea
$0.99 ea
$0.99 ea
$25.99 ea
$1.49 ea
$0.99 ea
$89.99 ea
$0.99 ea
$8.99 ea
$1.99 ft
$1.99 ea
$10.99 ea
$148.99 ea
$8.99 ea
$149.99 ea
$3.99 ea
$3.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$4.99 ea
$2.99 ea
$6.99 ea
$23.99 ea
$12.99 ea
$65.99 ea
$0.99 ea
$0.99 ea
$9.99 ea
$15.99 ea
$4.99 ea
$0.99 ea
$6.99 ea
$159.99 ea
$3.99 ea
MSRP
59
B111
B102
69
70
5
DESCRIPTION
4
5
quick disconnect, 1/4" female x 1/4" fpt
B102
hose, vac, 15' x 1-1/4" w/ 1 1/2 black cuffs
tool, upholstery w/valve
Cuff-Lynx, 1.25" hose cuff x 2" female cuff
Cuff-Lynx, 1-1/4" hose x male & female
cuties, 1/4" qd, strandard pack of 2
manaul, Mytee-Lite
A935
H701
H282
H122
H133
P590
ADM-8070
4
hose wrap, heat guard
sol hose, pigtail, 1/8 x 7 1/2
G079
cap, 2.5" threaded, tethered
sol hose, 1/5" x 15', 1/8 mpt x 1/4 mpt
G036
AH136
bushing, hex, 1/4" mpt x 1/8" fpt
quick disconnect, male, 1/4" male x 1/4" fpt
B101
B104
1
1
1
2
1
1
1
1
1
1
1
1
1
2
QTY.
DESCRIPTION
harness, electrical
A997
1
1
1
1
1
1
2
1
5
1
1
1
1
1
QTY.
PART NO.
qd, brass, 1/4" f x 1/4" fpt
adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex
plate, mounting, QD
45 deg, street elbow, brass, 1/4" male
hose, pulse, 3/8" x 14-1/2" (OAL), f
elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt
elbow, brass, 90 deg, 1/4" fpt x 1/4" fpt
valve, brass, 1/4" check
screw, 6 x 3/16, phil pan head, self-tapping
Thermostat, 310°F ± 10°F, Manual, 1/4"
Thermostat, 200°, Auto, 1/4"
heating rod, 1000W, 115V
heater, aluminum cast, single
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
ITEMS NOT SHOWN
B130
AH184
66
H484
B136
65
68
B207
64
67
B108
62
63
E574
H274
61
E573
E519
58
60
B103
H903A
57
PART NO.
ITEM
NO.
3
3
$2.99 ea
$9.99 ea
$3.99 ea
$98.99 ea
$43.99 ea
$14.99 ea
$2.99 ea
$3.99 ea
$44.99 ea
$1.99 ea
$17.49 ea
$8.49 ea
$47.99 ea
MSRP
$17.99 ea
$3.49 ea
$4.99 ea
$5.49 ea
$27.99 ea
$4.99 ea
$5.99 ea
$13.99 ea
$0.99 ea
$17.99 ea
$16.49 ea
$51.99 ea
$78.99 ea
$4.49 ea
MSRP
DATE
1/2014
NAME
M.LaBarbera
2
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
COMMENTS:
CHECKED
DRAWN
2
SCALE: 1:24
1
DO NOT
SCALE DRAWING
8070
F
REV
SHEET 1 OF 3
Mytee Lite
858-679-1191
SIZE DWG. NO.
C
TITLE:
mytee PRODUCTS, INC.
1
A
B
C
D
E
F
8070 MYTEE LITE™ PARTS & PRICING
Part prices are subject to change.
10
A
B
C
D
E
F
8
10
8
7
9
6
5
8
7
7
4
4
3
15
14
13
12
11
2
6
6
1
3
4
5
5
24
25
26
25
23
56
to pump
"IN"
thru B106A
20
22
27
4
29
28
4
19
18
21
40
17
16
39
41
36
37
42
3
33
32
31
17
47
63
to heater
"IN"
thru
31
45
48
49
34
4
35
44
38
43
3
31
46
50
4
49
to pump
"OUT"
thru AH157
53
63
51
DATE
2
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
4
70
58
23
56
to QD
thru B107
67
858-679-1191
66
to sol tank
thru B119
1
SCALE: 1:24
1
DO NOT
SCALE DRAWING
8070
F
REV
SHEET 2 OF 3
Mytee Lite
SIZE DWG. NO.
C
TITLE:
mytee PRODUCTS, INC.
64
68
1/2014
67
56
59
33
33
69
62
56
65
57
to heater
"OUT"
thru
64
61
55
NAME
60
9
54
M.LaBarbera
COMMENTS:
CHECKED
DRAWN
30
52
2
A
B
C
D
E
F
8070 MYTEE LITE™ PARTS & PRICING
1/15/2014
L2
L1
G
Primary Cord
11
E-515
E-515
E-515
1000 Watt Heat
G
L1
L2
Pump
VAC
L2
C-305
C-302P
L1
G
G
8070
115 Volt System
To Metal
Plate
8070 MYTEE LITE™ WIRING DIAGRAM
NOTES
Mytee Products Inc.
13655 Stowe Dr.
Poway, CA 92064
www.mytee.com
© 2016 Mytee Products Inc.
Printed in the U.S.A.
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising