S-3.5G Turbo User Manual

S-3.5G Turbo User Manual
R
S-3 .5 G TURBO
Manual contents
• Safety instructions
• Charging instructions
• Flying instructions
• Calibration control
• Battery installation
• Part list
Main motor 2
Tail motor
ON/OFF switch
Power
indicator light
Main motor 1
Infrared
directional
signal
Left / Right
Forward -Backward
throttle-stick
A/B band selector
Up / Down
throttle-stick
SPARE PARTS
Turbo ON/OFF
switch
Controller USB
charge port
Packing list
(1) Extreme indoor helicopter
(1) Infrared remote controller
(1) Set of extra blades
(1) USB charging wire
(1) Warranty registration card
(1) Instruction manual
Main blades
USB charging wire
Calibration trim L/R buttons
Tail blade
Parts - Service - Repairs ... www.ExtremeRcByRsi.com or call our MI service center: 586-757-1336 x 1
Battery cover
R/C
+
+
-
+
+
-
-
4
4 x1.5V ‘AA’ batteries
Remote control charging
Computer charging
WHEN CHARGING BE SURE TO TURN THE SWITCH ON THE HELICOPTER TO ‘OFF’
(A) Charging helicopter with Remote Controller: plug provided USB cord into R/C and into
helicopter. Turn on R/C, the light on the USB plug will light up until the helicopter is fully
charged - light will turn off when fully charged. A full charge takes approximately 60-minutes.
(B) Charging helicopter with computer: plug provided USB cord into computer and into helicopter.
Turn on R/C, the light on the USB plug will light up until the helicopter is fully charged - light
will turn off when fully charged. A full charge takes approximately 60-minutes.
Charge time: up to 60 minutes - Flight time: up to 10 minutes
Fresh alkaline batteries strongly recommended
FLYING YOUR HELICOPTER
Select band ‘A’ or ‘B’ by pressing band selector button down for 3 seconds (see pg.3).
Turn power switches for helicopter and R/C to ‘ON’-lights will turn on.
Point top of controller towards helicopter and step back 6-8 feet.
For best signal strength always keep the top of the R/C pointed towards the helicopter.
Turn safety off by moving left throttle up / down. You are now ready to start flying!
REMOTE CONTROL
THROTTLES
Parts - Service - Repairs ... www.ExtremeRcByRsi.com or call our MI service center: 586-757-1336 x 1
TURBO BUTTON
Low speed: press TURBO button once, power indicator light will flash once.
High speed: press TURBO button again, power indicator light will flash twice.
BAND SELECTOR
Press R/C center button with indicator.
Band A: press indicator button for 3 seconds, power indicator will flash once.
Band B: press indicator button again for 3 seconds, power indicator will fash twice.
Calibration Trim Control: if the helicopter is turning excessively to the right or left,
or turning out of control, adjust the trim control button using the instructions below.
IR
If helicopter rotates counter-clockwise ... Continually push right R/C calibration until excessive turning stops.
IR
If helicopter rotates clockwise ... Continually push left R/C calibration until excessive turning stops.
Parts - Service - Repairs ... www.ExtremeRcByRsi.com or call our MI service center: 586-757-1336 x 1
T
C
6
Use good common sense when flying!
x1
#
1
Head cover
#
2 Tail and fin set
#
3
Main blades
#
4 Blade connecting
buckles
#
5
#
6
Top blade
connectors
#
7 Rear tail blade
#
8 Body main-frame
#
9 Landing gear
#
10 Motor drive
gears
#
11
Main shaft
connector
#
12
Main frame
metal part
#
13 Tail support pipe
#
14 Tail - pipe with
motor
#
15 Main shaft pipe
#
16 Rear motor
#
17 Front motor
#
18 3.7V Battery
Li-Poly
#
19 Circuit board
with ON/OFF
switch
#
20 USB charging
wire
#
Balance bar
21 Remote Controller
Parts - Service - Repairs ... www.ExtremeRcByRsi.com or call our MI service center: 586-757-1336 x 1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising