Product overview
Product overview
Record player - Debut-Line
Debut III
Debut III E
Debut III/ Phono USB
Debut III/ Phono SB
Debut SE II
1 Xpression III
1 Xpression III Comfort
2 Xperience
2 Xperience Comfort
2 Xperience SuperPack
6 PerspeX
6 PerspeX Anniversary
Xtension
RPM 1 Genie
RPM 5
RPM 5 SuperPack
RPM 6.1 SB
RPM 6.1 SB SuperPack
RPM 9.1
RPM 9.1 SuperPack
RPM 9.1X
RPM 10
Record player - Classic-Line
Record player - RPM-Line
Models with an end-of-side switch-off: Pro-Ject Debut III E, Pro-Ject 1 Xpression III Comfort, and Pro-Ject 2 Xperience Comfort
Models with an electronic speed change between 33 and 45 r.p.m.: Pro-Ject Debut III /Phono SB, Pro-Ject 2 Xpression III Comfort, Pro-Ject 2 Xperience Comfort,
Pro-Ject 2 Xperience SuperPack 1 & 2, Pro-Ject RPM 5 SuperPack Pro-Ject RPM 6.1 SB, Pro-Ject RPM 6.1 SB SuperPack and Xtension
78 r.p.m. as a standard: Pro-Ject Debut III/ Phono SB, Pro-Ject 2 Xpression III Comfort, Pro-Ject RPM 5 SuperPack,
Pro-Ject RPM 6.1 SB, Pro-Ject RPM 6.1 SB SuperPack an Xtension
78 r.p.m. optional with all models except: Pro-Ject 2 Xperience, Pro-Ject 2 Xperience Comfort,
Pro-Ject 2 Xperience SuperPack 1 & 2, Pro-Ject 6 PerspeX, 6 PerspeX SuperPack, Pro-Ject RPM 9.1/9.1X,
Pro-Ject RPM 9.1 SuperPack 1 & 2 and Pro-Ject RPM 10
Models equipped with an internal MM phono stage: Pro-Ject Debut III/ Phono USB, Pro-Ject Debut III /Phono SB
Transparent plastic dust cover supplied with all models except Pro-Ject RPM 5, Pro-Ject RPM 5 SuperPack,
Pro-Ject RPM 6.1 SB, Pro-Ject RPM 6.1 SB SuperPack, Pro-Ject RPM 9.1/9.1X, Pro-Ject RPM 9.1 SuperPack 1 & 2 and RPM 10
Dust cover optional: Pro-Ject RPM 9.1, Pro-Ject 9.1X and Pro-Ject RPM 9.1 SuperPack 1 & 2
Universal dust cover Pro-Ject Cover it optional: Pro-Ject RPM 5, Pro-Ject RPM 5 SuperPack,
Pro-Ject RPM 6.1 SB, Pro-Ject RPM 6.1 SB SuperPack, Pro-Ject RPM 9.1/9.1X, Pro-Ject RPM 9.1 SuperPack 1 & 2 and Pro-Ject RPM 10
Technical specifications
Dimensions W x H x D
Fitted cartridge
Built in phono pre-amplifier (MM)
A/D converter with USB output
Nominal speeds
Electronic speed change
End-of-side switch-off
Dust cover
RCA phono sockets
Feet / damping material
Tonearm
Armtube / headshell made of
Eff. tonearm length / eff. tonearm mass
Overhang
Downforce range
Speed variance
Wow and flutter
Signal to noise
Platter – weight / diameter
Power consumption
Dimensions (dust cover open)
Dimensions (dust cover closed)
Weight
Debut III
Debut III E
Debut III/Phono USB
Debut III/Phono SB
Debut SE II
Ortofon OM 5E
–
–
A
33 / 45 / 78
–
–
8
Ortofon OM 5E
–
–
B
33 / 45
–
8
8
Ortofon OM 5E
8
8
Ortofon OM 5E
8
Ortofon 510 mk II
–
–
A
33 / 45 / 78
–
–
8
8
A
33 / 45 / 78
–
–
8
8
C
–
33 / 45 / 78
8
–
8
–
–
–
PVC / rubber
PVC / rubber
PVC / rubber
PVC / rubber
aluminium cones / rubber
Pro-Ject 8.6
Pro-Ject 8.6
Pro-Ject 8.6
Pro-Ject 8.6
Pro-Ject 8.6
aluminium / aluminium aluminium / aluminium aluminium / aluminium aluminium / aluminium aluminium / aluminium
8,6“ (218,5mm) / 9,5 g 8,6“ (218,5mm) / 9,5 g 8,6“ (218,5mm) / 9,5 g 8,6“ (218,5mm) / 9,5 g 8,6“ (218,5mm) / 9,5 g
18,5 mm
18,5 mm
18,5 mm
18,5 mm
18,5 mm
10 - 30 mN
10 - 30 mN
10 - 30 mN
10 - 30 mN
10 - 30 mN
±0,8 %
±0,8 %
±0,8 %
±0,8 %
±0,8 %
±0,12%
±0,12%
±0,12%
±0,12%
±0,12%
-65dB
-65dB
-65dB
-65dB
-65dB
1,3 kg / 280mm
1,3 kg / 280mm
1,3 kg / 280mm
1,3 kg / 280mm
2,2 kg/300mm
2W
2W
2W
6,5W
2W
415 x 365 x 405mm
415 x 365 x 405mm
415 x 365 x 405mm
415 x 365 x 405mm
415 x 365 x 405mm
415 x 118 x 320mm
415 x 118 x 320mm
415 x 118 x 320mm
415 x 118 x 320mm
415 x 118 x 320mm
5,5kg
5,5kg
6kg
6kg
6,9kg
A Electronic speed change between 33 and 45 r.p.m. when the optional Pro-Ject Speed Box II (Pro-Ject Speed Box SE II) is used.
Using the Pro-Ject Speed Box II (Pro-Ject Speed Box SE II), 78 r.p.m. is available after fitting a special pulley, which may be purchased as an optional extra.
B Switching between 33 and 45 r.p.m. is done manually. The Debut III E can not be used with the Pro-Ject Speed Box II (Pro-Ject Speed Box SE II).
C Electronic speed change between 33 and 45 r.p.m.. Switching to 78 r.p.m. is done manually.
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
2
Technical specifications
Dimensions W x H x D
1 Xpression III
1 Xpression III Comfort
6 PerspeX
6 PerspeX SuperPack
Fitted cartridge
Magnet supported sub-chassis
Nominal speeds
Electronic speed change
End-of-side switch-off
Dust cover
Motor in a separate housing
Record clamp / record puck
RCA phono sockets
Feet / damping material
Tonearm
Armtube / headshell made of
Eff. tonearm length / eff. tonearm mass
Overhang
Supplied counterweights for cartridge weight
Ortofon 2M Red
–
A
33 / 45 / 78
–
–
8
Ortofon 2M Red
–
C
33 / 45 / 78
8
8
8
–
8
Ortofon MC Valencia
8
–
–
8
–
–
8
aluminium cones / rubber
Pro-Ject 8.6c
carbon-fibre / aluminium
8,6“ (218,5mm) / 8,7g
18,5 mm
7 - 12g
aluminium cones / rubber
Pro-Ject 8.6c
carbon-fibre / aluminium
8,6“ (218,5mm) / 8,7g
18,5 mm
7 - 12g
Optional counterweights for cartridge weight
Downforce range
Speed variance
Wow and flutter
Signal to noise
Platter – weight / diameter
Power consumption
Dimensions (dust cover open)
Dimensions (dust cover closed)
Weight
4 - 7g
10 - 30 mN
±0,5 %
±0,1%
-70 dB
0,9kg / 300mm
2W
415 x 370 x 400mm
415 x 118 x 320mm
5,5kg
4 - 7g
10 - 30 mN
±0,5 %
±0,1%
-70 dB
0,9kg / 300mm
10W
415 x 370 x 400mm
415 x 118 x 320mm
5,5kg
D
33 / 45
–
–
8
8
record clamp
8
D
33 / 45
–
–
8
8
record clamp
8
aluminium cones / Sorbothane aluminium cones / Sorbothane
Pro-Ject 9cc Evolution
Pro-Ject 9cc Evolution
carbon-fibre / carbon-fibre
carbon-fibre / carbon-fibre
9“ (230mm) / 8g
9“ (230mm) / 8g
18 mm
18 mm
5 - 7,5g, 7 - 10g
5 - 7,5g, 7 - 10g
9 - 11g, 10 - 14g
9 - 11g, 10 - 14g
–
–
15 - 30 mN
15 - 30 mN
±0,5 %
±0,5 %
±0,06 %
±0,06 %
-73 dB
-73 dB
2kg / 300mm
2kg / 300mm
2W
2W
460 x 420 x 465mm
460 x 420 x 465mm
460 x 160 x 365mm
460 x 160 x 365mm
10,5
10,5
A Electronic speed change between 33 and 45 r.p.m. when the optional Pro-Ject Speed Box II (Pro-Ject Speed Box SE II) is used.
Using the Pro-Ject Speed Box II (Pro-Ject Speed Box SE II), 78 r.p.m. is available after fitting a special pulley, which may be purchased as an optional extra.
C Electronic speed change between 33 and 45 r.p.m.. Switching to 78 r.p.m. is done manually.
D Electronic speed change between 33 and 45 r.p.m. when the optional Pro-Ject Speed Box II (Pro-Ject Speed Box SE II) is used.
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
3
Technical specifications
Dimensions W x H x D
Fitted cartridge
Nominal speeds
Electronic speed change
End-of-side switch-off
Dust cover
Record clamp / record puck
Inverted main bearing with ceramic thrust-pad
Magnet supported main bearing
Central metal block damps main bearing
RCA phono sockets
Feet / damping material
Magnet supported feet
Tonearm
Armtube / headshell made of
Eff. tonearm length / eff. tonearm mass
Overhang
Supplied counterweights for cartridge weight
Optional counterweights for cartridge weight
Downforce range
Speed variance
Wow and flutter
Signal to noise
Platter – weight / diameter
Power consumption
Dimensions (dust cover open)
Dimensions (dust cover closed)
Weight
2 Xperience
2 Xperience Comfort
2 Xperience SuperPack 1/2
*Ortofon M2 Red,
SP1 Ortofon MC Rondo Red
*Sumiko Blue Point No. 2 or
SP2 Ortofon MC Salsa
**Ortofon MC Rondo Red
D
E
E
33 / 45
33 / 45
33 / 45
8
8
–
8
–
–
8
8
8
record clamp
record clamp
record clamp
–
–
–
–
–
–
–
–
–
8
8
8
aluminium cones / Sorbothane aluminium cones / Sorbothane aluminium cones / Sorbothane
–
–
–
Pro-Ject 9c
Pro-Ject 9c
Pro-Ject 9c
carbon-fibre / aluminium
carbon-fibre / aluminium
carbon-fibre / aluminium
9“ (230mm) / 9,5g
9“ (230mm) / 9,5g
9“ (230mm) / 9,5g
18 mm
18 mm
18 mm
6 - 9g
6 - 9g*, 9 - 11g**
9 - 11g
10 - 15g, 9 - 11g, 4 - 6g
10 - 15g, 9 - 11g, 4 - 6g
15 - 10g, 6 - 9g, 4 - 6g
10 - 30 mN
10 - 30 mN
10 - 30 mN
±0,5 %
±0,5 %
±0,5 %
±0,08 %
±0,08 %
±0,08 %
-70 dB
-70 dB
-70 dB
2,0 kg / 300mm
2,0 kg / 300mm
2,0 kg / 300mm
2W
10W
2W
460 x 390 x 460mm
460 x 417 x 460mm
460 x 390 x 460mm
460 x 133 x 350mm
460 x 160 x 350mm
460 x 133 x 350mm
7,6kg
7,7kg
7,6kg
Xtension
–
–
C
33 / 45 / 78
8
–
8
record puck
8
8
8
8 Pro-Ject tonearms only
aluminium / Sorbothane
8
Pro-Ject 9cc Evolution
Pro-Ject 9cc Evolution
Ortofon AS-212S
Ortofon AS-309S
Ortofon RS-212D
Ortofon RS-309D
without tonearm
±0,09%
±0,01%
-73 dB
5,7 kg / 300mm
2W
550 x 550 x 560mm
550 x 250 x 450mm
20kg
C Electronic speed change between 33 and 45 r.p.m.. Switching to 78 r.p.m. is done manually.
D Electronic speed change between 33 and 45 r.p.m. when the optional Pro-Ject Speed Box II (Pro-Ject Speed Box SE II) is used.
E Electronic speed change between 33 and 45 r.p.m..
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
4
Technical specifications
Dimensions W x H x D
Fitted cartridge
Nominal speeds
Electronic speed change
Dust cover
Record clamp / record puck
Inverted main bearing with ceramic thrust-pad
Central metal block damps main bearing
RCA phono sockets
Feet / damping material
Tonearm
Armtube / headshell made of
Eff. tonearm length / eff. tonearm mass
Overhang
Supplied counterweights for cartridge weight
Optional counterweights for cartridge weight
Downforce range
Speed variance
Wow and flutter
Signal to noise
Platter – weight / diameter
Power consumption
Dimensions (dust cover open)
Weight
RPM 1 Genie
RPM 5 / RPM 5 SuperPack
RPM 6.1 SB
RPM 6.1 SB SuperPack
Ortofon OM 3E
–
Ortofon MC Samba
–
8
Ortofon 2M Red / Pro-Ject
Pick it MC1H
A/C
33 / 45 / 78
– / 8
Cover it optional
record clamp
–
8
8
ABS plastic
Pro-Ject 8.6s
aluminium / aluminium
8,6“ (218,5mm) / 8,5g
19 mm
4 - 9g
–
15 - 30 mN
±0,8 %
±0,15%
-70 dB
1,6kg / 300mm
2W
* 380 x 115 x 350mm
3,3kg
aluminium cones / rubber
Pro-Ject 9c
carbon-fibre / aluminium
9“ (230mm) / 9,5g
18 mm
6 - 10g
10 - 15g, 9 - 11g, 4 - 6g
10 - 30 mN
±0,5 %
±0,08 %
-70 dB
1,75 kg / 300mm
2W
* 371 x 145 x 300mm
6,5kg
A
33 / 45 / 78
–
–
–
8
C
33 / 45 / 78
8
Cover it optional
record puck
8
8
8
C
33 / 45 / 78
8
Cover it optional
record puck
8
8
8
aluminium cones / Sorbothane aluminium cones / Sorbothane
Pro-Ject 9c
Pro-Ject 9c
carbon-fibre / aluminium
carbon-fibre / aluminium
9“ (230mm) / 9,5g
9“ (230mm) / 9,5g
18 mm
18 mm
6 - 10g
6 - 10g
10 - 15g, 9 - 11g, 4 - 6g
10 - 15g, 9 - 11g, 4 - 6g
10 - 30 mN
10 - 30 mN
±0,5 %
±0,5 %
±0,08 %
±0,08 %
-70 dB
-70 dB
3,5kg / 330mm
3,5kg / 330mm
6W
6W
* 385 x 170 x 330mm
* 385 x 170 x 330mm
8kg
8kg
A Electronic speed change between 33 and 45 r.p.m. when the optional Pro-Ject Speed Box II (Pro-Ject Speed Box SE II) is used.
Using the Pro-Ject Speed Box II (Pro-Ject Speed Box SE II), 78 r.p.m. is available after fitting a special pulley, which may be purchased as an optional extra.
C Electronic speed change between 33 and 45 r.p.m.. Switching to 78 r.p.m. is done manually.
* Without dust cover. Dust cover Pro-Ject Cover it optional. Dimensions Cover it 1: 525 x 290 x 425mm. Dimensions Cover it 2: 460 x 225 x 365mm
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
5
Technical specifications
Dimensions W x H x D
RPM 9.1 / RPM 9.1X
RPM 9.1 SuperPack 1
RPM 9.1 SuperPack 2
RPM 10
Fitted cartridge
–
Ortofon MC W-10
Sumiko Blue Point No. 2
–
D
C
C
D
Nominal speeds
33 / 45
33 / 45
33 / 45
33 / 45
8
8
Electronic speed change
–
–
Dust cover
Cover it optional
Cover it optional
Cover it optional
Cover it optional
8
8
8
8
Motor in a separate housing
Record clamp / record puck
record puck
record puck
record puck
record puck
Inverted main bearing with ceramic thrust-pad
8/8
8/8
8/8
8/8
8
Magnet supported main bearing
–
–
–
8
8
8
8
Central metal block damps main bearing
8
8
8
Granulate filled plinth
–
8
Granulate filled equipment base Ground it deluxe 1
–
–
–
8
8
8
8
RCA phono sockets
Feet / damping material
aluminium cones / Sorbothane aluminium cones / Sorbothane aluminium cones / Sorbothane aluminium cones / Sorbothane
Tonearm
Pro-Ject 9cc
Pro-Ject 9cc
Pro-Ject 9cc
Pro-Ject 10cc
Armtube / headshell made of
carbon-fibre / carbon-fibre
carbon-fibre / carbon-fibre
carbon-fibre / carbon-fibre
carbon-fibre / carbon-fibre
Eff. tonearm length / eff. tonearm mass
9“ (230mm) / 8,5g
9“ (230mm) / 8,5g
9“ (230mm) / 8,5g
10“ (254mm) / 9g
Overhang
18 mm
18 mm
18 mm
16 mm
Supplied counterweights for cartridge weight
6 - 10g
8 - 11g
6 - 10g
6 - 9g
Optional counterweights for cartridge weight
11 - 15g, 8 - 11g, 5 - 8g
11 - 15g, 6 - 10g, 5 - 8g
11 - 15g, 8 - 11g, 5 - 8g
10 - 15g, 7 - 11g
Downforce range
10 - 30 mN
10 - 30 mN
10 - 30 mN
10 - 35 mN
Speed variance
±0,5 %
±0,5 %
±0,5 %
± 0 , 5%
Wow and flutter
±0,06 %
±0,06 %
±0,06 %
± 0 , 01 %
Signal to noise
-73 dB
-73 dB
-73 dB
-73 dB
Platter – weight / diameter
3,5kg / 300mm
3,5kg / 300mm
3,5kg / 300mm
5,4kg / 300mm
Power consumption
2W
2W
2W
2W
Dimensions (dust cover open)
* 440 x 180 x 325mm
* 440 x 180 x 325mm
* 440 x 180 x 325mm
* 480 x 210 x 330mm
Weight
10,5kg + 2kg Motor
10,5kg + 2kg Motor
10,5kg + 2kg Motor
14,5kg + 2kg Motor
D Electronic speed change between 33 and 45 r.p.m. when the optional Pro-Ject Speed Box II (Pro-Ject Speed Box SE II) is used.
C Electronic speed change between 33 and 45 r.p.m..
* Without dust cover. Dust cover Pro-Ject Cover it optional. Dimensions Cover it 1: 525 x 290 x 425mm. Dimensions Cover it 2: 460 x 225 x 365mm
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
6
Technical specifications
1”= 2,54cm
Headshell 0,5” standard:
Mounting distance arm base
Armtube made of
Headshell made of
Eff. tonearm length
Eff. tonearm mass
Overhang
Supplied counterweights for
cartridge weight
Optional counterweights for
cartridge weight
Downforce range
Weight (without counterweight)
Pro-Ject 9
Pro-Ject 9c
Pro-Ject 9cc
Pro-Ject 9cc
Evolution
Pro-Ject 10cc
Pro-Ject 10cc
Evolution
Pro-Ject 12cc
Pro-Ject 12cc
Evolution
8
8
8
8
8
8
8
8
212mm
aluminium
aluminium
9“ (230mm)
11g
18 mm
6 - 14g
------------------2 - 6g
4 - 10g
10 - 16g
10 - 35 mN
250g
212mm
carbon-fibre
aluminium
9“ (230mm)
11g
18 mm
6 - 9g
------------------4 - 6g
9 - 11g
10 - 15g
10 - 35 mN
250g
212mm
carbon-fibre
carbon-fibre
9“ (230mm)
8,5g
18 mm
6 - 10g
------------------3 - 6g
5 - 8g
11 - 15g
10 - 30 mN
250g
212mm
carbon-fibre
carbon-fibre
9“ (230mm)
8g
18 mm
5 - 7,5g
7 - 10g
9 - 11g
10 - 14g
------------------10 - 35 mN
265g
238mm
carbon-fibre
carbon-fibre
10“ (254mm)
9g
16 mm
6 - 9g
------------------2 - 5g
7 - 11g
10 - 15g
10 - 35 mN
254g
238mm
carbon-fibre
carbon-fibre
10“ (254mm)
8,5g
16 mm
4 - 6g
5 - 8g
6 - 10g
8 - 14g
------------------10 - 35 mN
269g
291,6mm
291,6mm
carbon-fibre
carbon-fibre
carbon-fibre
carbon-fibre
12“ (304,8mm) 12“ (304,8mm)
10,5g
10,5g
13,2mm
13,2mm
4 - 6g
4 - 7g
7 - 9g
6 - 9g
------8 - 12g
------10 - 15g
9,5 - 13g
------------------------------10 - 35 mN
10 - 35 mN
257g
271g
All tonearms are available either with flying leads terminated with a 5-pole standard tonearm socket, or with a cable terminated with RCA phono sockets.
9" Tonearms fit record players fitted with mounting boards drilled to the Linn standard geometry.
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
7
Product information
Pro-Ject 9cc Evolution
9" precision tonearm with carbon-fibre armtube
The tonearm's design efficiently leads parasitic vibrations away from the cartridge into the mounting board,
guarantees the precise tracing of the record groove by the needle and also facilitates fine adjustment of vertical
and horizontal tracing due to the following constructional details:
The headshell and armtube are fashioned from a single piece of carbon-fibre.
Conical armtube avoids standing wave reflections.
Inverted bearing design with four ABEC7 spec ballraces.
Arm bearing housing of solid ring type. The massive outside ring is open to avoid resonances.
Sorbothane®-damped counterweight effectively counteracts unwanted resonances.
Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing warped
records.
Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
Straight armtube reduces toe-in error.
Silicone-damped armlift can be adjusted to suit arm height.
The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated
phono sockets.
Available with 5-pole standard socket, flying leads or terminal with phono sockets and earth screw.
Technical specifications
Headshell:
Mounting distance:
Supplied counterweight:
Downforce range:
Effective length:
Effective mass:
Overhang:
Weight:
0,5” (12,7mm) standard
212mm (platter
tonearm base, Linn standard mount)
suitable for cartridges weighing between 5 - 7,5g, 7 - 10g, 9 - 11g and 10 - 14g
10 - 35mN
9” (230mm)
8g
18mm
265g (without counterweight)
The manufacturer reserves the right to alter the technical specifications without notice.
8
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
Product information
Pro-Ject 10cc Evolution
10" precision tonearm with carbon-fibre armtube
The tonearm's design efficiently leads parasitic vibrations away from the cartridge into the mounting board,
guarantees the precise tracing of the record groove by the needle and also facilitates fine adjustment of vertical
and horizontal tracing due to the following constructional details:
The headshell and armtube are fashioned from a single piece of carbon-fibre.
Conical armtube avoids standing wave reflections.
Inverted bearing design with four ABEC7 spec ballraces.
Arm bearing housing of solid ring type. The massive outside ring is open to avoid resonances.
Sorbothane®-damped counterweight effectively counteracts unwanted resonances.
Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing warped
records.
Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
Straight armtube reduces toe-in error.
Silicone-damped armlift can be adjusted to suit arm height.
The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated
phono sockets.
Available with 5-pole standard socket, flying leads or terminal with phono sockets and earth screw.
Technical specifications
Headshell:
Mounting distance:
Supplied counterweight:
Downforce range:
Effective length:
Effective mass:
Overhang:
Weight:
0,5” (12,7mm) standard
238mm (platter
tonearm base)
suitable for cartridges weighing between 4 - 6g, 5 - 8g, 6 - 10g and 8 - 15g
10 - 35mN
10” (254mm)
8,5g
16mm
269g (without counterweight)
The manufacturer reserves the right to alter the technical specifications without notice.
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
9
Product information
Pro-Ject 12cc Evolution
12" precision tonearm with carbon-fibre armtube
The tonearm's design efficiently leads parasitic vibrations away from the cartridge into the mounting board,
guarantees the precise tracing of the record groove by the needle and also facilitates fine adjustment of vertical
and horizontal tracing due to the following constructional details:
The headshell and armtube are fashioned from a single piece of carbon-fibre.
Conical armtube avoids standing wave reflections.
Inverted bearing design with four ABEC7 spec ballraces.
Arm bearing housing of solid ring type. The massive outside ring is open to avoid resonances.
Sorbothane®-damped counterweight effectively counteracts unwanted resonances.
Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing warped
records.
Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
Straight armtube reduces toe-in error.
Silicone-damped armlift can be adjusted to suit arm height.
The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated
phono sockets.
Available with 5-pole standard socket, flying leads or terminal with phono sockets and earth screw.
Technical specifications
Headshell:
Mounting distance:
Supplied counterweight:
Downforce range:
Effective length:
Effective mass:
Overhang:
Weight:
0,5” (12,7mm) standard
291,6mm (platter
tonearm base)
suitable for cartridges weighing between 4 - 7g, 6 - 9g, 8 - 12g and 10 - 15g
10 - 35mN
12” (304,8mm)
10,5g
13,2mm
271g (without counterweight)
The manufacturer reserves the right to alter the technical specifications without notice.
10
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
Product information
Pro-Ject Align it
Cartridge alignment tool
Tool for cartridge alignment and adjustment
Special slip-proof tool for defining the turning centre of Pro-Ject tonearms
Adaptable to accommodate differing tonearm lengths
Suitable for other manufacturers’ tonearms
Suitable for tonearms between 8” (203mm) and 12“(305mm) effective length
The manufacturer reserves the right to alter the technical specifications without notice.
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
11
Product information
Pro-Ject Measure it
Electronic stylus balance
4 digit LCD-Display with backlight
Capacity 0 - 5g
Variance ±0,002g
Auto calibration function
Auto off after 120 seconds
Replacement batteries supplied
The manufacturer reserves the right to alter the technical specifications without notice.
12
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
Product information
Pro-Ject Ground it deluxe 1 & 2
Equipment bases
Dark grey piano lacquer finish (like Pro-Ject RPM 5, RPM 9.1 and RPM 10)
Filled with granulate for universal damping
Height-adjustable spikes. Three or four spikes may be fitted according to taste/application.
Dimensions Ground it deluxe 1 (W x H x D):
Dimensions Ground it deluxe 2 (W x H x D):
Weight Ground it deluxe 1:
Weight Ground it deluxe 2:
500 x 65 x 400mm (height incl. spikes). Height without feet 450mm
435 x 65 x 340mm (height incl. spikes). Height without feet 450mm
11,6kg
8,5kg
Pro-Ject Cover it 1 & 2
Universal dust cover
Outside dimensions Cover it 1 (W x H x D):
Outside dimensions Cover it 2 (W x H x D):
Inside dimensions Cover it 1 (W x H x D):
Inside dimensions Cover it 2 (W x H x D):
Weight Cover it 1:
Weight Cover it 2:
525 x 290 x 425mm
460 x 225 x 365mm
515 x 285 x 415mm
450 x 250 x 355mm
4,3kg
2,9kg
The manufacturer reserves the right to alter the technical specifications without notice.
Picture: the Pro-Ject Ground it deluxe 2 supporting a Pro-Ject RPM 9.1 (not included).
The Pro-Ject RPM 10 is supplied complete with a Ground it deluxe 1.
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
13
Product information
Pro-Ject Wallmount it
Wall mount equipment racks
Wallmount it 1
Welded steel frame construction with
four height-adjustable spikes to level the board.
Veneered wooden board, black finish
Surface area (w x d): 460 x 355mm
Overall dimensions (w x h x d): 460 x 90 x 415mm
Wallmount it 2
Welded steel frame construction with
four height-adjustable spikes to level the board.
Veneered wooden board, black finish
Surface area (w x d): 460 x 355mm
Overall dimensions (w x h x d): 490 x 260 x 455mm
Wallmount it 3
Screwed steel construction with
three height-adjustable spikes to level the board.
Matt black MDF board.
Surface area (w x d): 520 x 450mm
Overall dimensions (w x h x d): 635 x 290 x 455mm
The manufacturer reserves the right to alter the technical specifications without notice.
14
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
Product information
Pro-Ject Debut III
Manual turntable with fitted
cartridge Ortofon OM 5E
Turntable
Chassis available in matt black, glossy black, silver, glossy white, red, yellow, blue and green
A quiet running AC motor with a two-step metal pulley drives the hub and platter via a flat-ground belt.
The medium density fibre plinth stands on four feet which act as shock absorbers.
The motor is decoupled from the plinth to reduce vibration transmission.
The platter is a sandwich construction utilising the hub, a sheet-steel platter weighing 1,3Kg and a felt mat.
The platter's low-tolerance chrome-plated stainless-steel axle runs on a polished ball bearing in a brass
bearing housing.
External power supply avoids potential electro-mechanical interference.
Tonearm Pro-Ject 8.6
The turntable is supplied with Ortofon OM 5E MM-cartridge fitted.
Uniform material: the tonearm tube and bearing housing are constructed from aluminium.
The headshell and undamped armtube are fashioned from a single piece.
The inverted horizontal bearings consist of two hardened stainless steel points bearing in sapphire cushes.
Flexible counterweight shaft avoids vibration at undesirable frequencies.
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
The straight armtube with an effective length of 8,6" reduces toe-in error.
The internal wiring consists of high-grade flexible copper from the headshell right through to the connection cable.
The connection cable has gold-plated plugs and appropriate capacitance and inductance values.
Dimensions W x H x D: With dust cover closed 415 x 118 x 320mm, dust cover open 415 x 365 x 405mm.
Cartridge: Output voltage 4mV. Recommended load resistance 47kohms (MM-input).
The manufacturer reserves the right to alter the technical specifications without notice.
The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process.
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
15
Product information
Pro-Ject Debut III E
Manual turntable with automatic
cut-off and fitted cartridge Ortofon OM 5E
Turntable
Chassis available in silver or matt black
A quiet running AC motor with a two-step metal pulley drives the hub and platter via a flat-ground belt.
The medium density fibre plinth stands on four feet which act as shock absorbers.
The motor is decoupled from the plinth to reduce vibration transmission.
The platter is a sandwich construction utilising the hub, a sheet-steel platter weighing 1,3Kg and a felt mat.
The platter's low-tolerance chrome-plated stainless-steel axle runs on a polished ball bearing in a brass
bearing housing.
An opto-electronic switch stops the motor as soon as the cartridge has reached the run-out groove.
External power supply avoids potential electro-mechanical interference.
Tonearm Pro-Ject 8.6
The turntable is supplied with Ortofon OM 5E MM-cartridge fitted.
Uniform material: the tonearm tube and bearing housing are constructed from aluminium.
The headshell and undamped armtube are fashioned from a single piece.
The inverted horizontal bearings consist of two hardened stainless steel points bearing in sapphire cushes.
Flexible counterweight shaft avoids vibration at undesirable frequencies.
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
The straight armtube with an effective length of 8,6" reduces toe-in error.
The internal wiring consists of high-grade flexible copper from the headshell right through to the connection cable.
The connection cable has gold-plated plugs and appropriate capacitance and inductance values.
Dimensions W x H x D: With dust cover closed 415 x 118 x 320mm, dust cover open 415 x 365 x 405mm.
Cartridge: Output voltage 4mV. Recommended load resistance 47kohms (MM-input).
The manufacturer reserves the right to alter the technical specifications without notice.
The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process.
If a cartridge of differing height is used it may be necessary to adjust the automatic cut-off.
16
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
Product information
Pro-Ject Debut III/Phono SB
Manual turntable with electro mechanic speed
change, fitted cartridge Ortofon OM 5E and
integrated MM phono pre-amplifier
Turntable
Chassis available in silver or matt black
A quiet running AC motor with a two-step metal pulley drives the hub and platter via a flat-ground belt.
The medium density fibre plinth stands on four feet which act as shock absorbers.
The motor is decoupled from the plinth to reduce vibration transmission.
The platter is a sandwich construction utilising the hub, a sheet-steel platter weighing 1,3Kg and a felt mat.
The platter's low-tolerance chrome-plated stainless-steel axle runs on a polished ball bearing in a brass
bearing housing.
Electronic speed change for 33 / 45 r.p.m. Switching to 78 r.p.m. is done manually.
External power supply avoids potential electro-mechanical interference.
Tonearm Pro-Ject 8.6
The turntable is supplied with Ortofon OM 5E MM-cartridge fitted.
Uniform material: the tonearm tube and bearing housing are constructed from aluminium.
The headshell and undamped armtube are fashioned from a single piece.
The inverted horizontal bearings consist of two hardened stainless steel points bearing in sapphire cushes.
Flexible counterweight shaft avoids vibration at undesirable frequencies.
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
The straight armtube with an effective length of 8,6" reduces toe-in error.
The internal wiring consists of high-grade flexible copper from the headshell right through to the connection cable.
The connection cable has gold-plated plugs and appropriate capacitance and inductance values.
A supplied 3,5 mm connector can be used to connect your Pro-Ject Debut III / Phono to any line level/auxiliary
input (Computer, Midi System, Mixer etc.).
Dimensions W x H x D: With dust cover closed 415 x 118 x 320mm, dust cover open 415 x 365 x 405mm.
Phono Pre-amplifier
Optimal channel separation through dual-mono circuitry
Technical specifications Phono Pre-amplifier
Noise floor:
THD:
Input impedance:
Power consumption:
Gain:
Output voltage typically:
RIAA-equalisation curve accuracy:
88dB
0,005%
47kohms/100pF
16V/40mA AC
32dB
160mV/1kHz at 4mV/1kHz
> 0,5dB/20Hz - 20kHz
The manufacturer reserves the right to alter the technical specifications without notice.
The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process.
The unit may only be connected to a line level input.
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
17
Product information
Pro-Ject Debut III/Phono USB
Manual turntable with fitted cartridge
Ortofon OM 5E and
integrated MM phono pre-amplifier with
A/D converter and USB output
Turntable
Chassis available in silver or matt black
A quiet running AC motor with a two-step metal pulley drives the hub and platter via a flat-ground belt.
The medium density fibre plinth stands on four feet which act as shock absorbers.
The motor is decoupled from the plinth to reduce vibration transmission.
The platter is a sandwich construction utilising the hub, a sheet-steel platter weighing 1,3Kg and a felt mat.
The platter's low-tolerance chrome-plated stainless-steel axle runs on a polished ball bearing in a brass
bearing housing.
External power supply avoids potential electro-mechanical interference.
Tonearm Pro-Ject 8.6
The turntable is supplied with Ortofon OM 5E MM-cartridge fitted.
Uniform material: the tonearm tube and bearing housing are constructed from aluminium.
The headshell and undamped armtube are fashioned from a single piece.
The inverted horizontal bearings consist of two hardened stainless steel points bearing in sapphire cushes.
Flexible counterweight shaft avoids vibration at undesirable frequencies.
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
The straight armtube with an effective length of 8,6" reduces toe-in error.
The internal wiring consists of high-grade flexible copper from the headshell right through to the connection cable.
The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated
phono sockets.
A supplied 3,5 mm connector can be used to connect your Pro-Ject Debut III / Phono to any line level/auxiliary
input (Computer, Midi System, Mixer etc.).
Dimensions W x H x D: With dust cover closed 415 x 118 x 320mm, dust cover open 415 x 365 x 405mm.
Phono Pre-amplifier
Optimal channel separation through dual-mono circuitry
Digitalisation of analog signals for recording direct to disk via USB with suitable recording programs
Runs on Windows™ and Mac OS™operating systems
Technical specifications Phono Pre-amplifier - A/D converter
Noise floor:
THD:
Input impedance:
Power consumption:
Gain:
Output voltage typically:
RIAA-equalisation curve accuracy:
USB output:
88dB
0,005%
47kohms/100pF
16V/40mA AC
32dB
160mV/1kHz at 4mV/1kHz
> 0,5dB/20Hz - 20kHz
digital serial data protocol USB 1.1
The manufacturer reserves the right to alter the technical specifications without notice.
The unit may only be connected to a line level input.
18
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
Product information
Pro-Ject Debut SE II
Manual turntable with fitted cartridge
Ortofon 510 mk II
Turntable
Chassis matt black
A quiet running AC motor with a two-step metal pulley drives the hub and platter via a flat-ground belt.
The medium density fibre plinth stands on three height-adjustable rubber-damped aluminium cones.
The motor is decoupled from the plinth to reduce vibration transmission.
The platter is a sandwich construction utilising the hub, a fine-balanced aluminium alloy platter weighing
2,2Kg and a felt mat.
The platter's low-tolerance chrome-plated stainless-steel axle runs on a polished ball bearing in a brass
bearing housing.
Connection to the phono input of the amplifier can be made with connecting cables of your taste through the
gold plated phono sockets and earth screw. A standard cable is provided.
External power supply avoids potential electro-mechanical interference.
Tonearm Pro-Ject 8.6
The turntable is supplied with Ortofon 510 mk II MM-cartridge fitted.
Uniform material: the tonearm tube and bearing housing are constructed from aluminium.
The headshell and undamped armtube are fashioned from a single piece.
The inverted horizontal bearings consist of two hardened stainless steel points bearing in sapphire cushes.
Flexible counterweight shaft avoids vibration at undesirable frequencies.
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
The straight armtube with an effective length of 8,6" reduces toe-in error.
The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated
phono sockets.
Dimensions W x H x D: With dust cover closed 415 x 118 x 320mm, dust cover open 415 x 365 x 405mm.
Cartridge: Output voltage 3mV. Recommended load resistance 47kohms (MM-input).
The manufacturer reserves the right to alter the technical specifications without notice.
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
19
Product information
Pro-Ject 1 Xpression III
Manual turntable with fitted cartridge
Ortofon 2M Red
Turntable
Chassis piano-lacquered dark grey
A quiet running AC motor with a two-step metal pulley drives the hub and platter via a flat-ground belt.
The medium density fibre plinth stands on three height-adjustable rubber-damped aluminium cones.
The motor is decoupled from the plinth to reduce vibration transmission.
The resonance-optimised platter is a sandwich construction utilising the hub and an acrylic platter.
The platter's low-tolerance chrome-plated stainless-steel axle runs on a polished ball bearing in a brass
bearing housing.
Connection to the phono input of the amplifier can be made with connecting cables of your taste through the
gold plated phono sockets and earth screw. A standard cable is provided.
External power supply avoids potential electro-mechanical interference.
Tonearm Pro-Ject 8.6c
The turntable is supplied with Ortofon 2M Red-cartridge fitted.
Conical carbon-fibre armtube avoids standing wave reflections.
Low mass aluminium headshell securely glued to armtube.
The inverted bearings consist of four hardened stainless steel points bearing in sapphire cushes.
Flexible counterweight shaft avoids vibration at undesirable frequencies.
Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
The straight armtube with an effective length of 8,6" reduces toe-in error.
Silicone-damped armlift can be adjusted to suit working height of the arm.
The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated
phono sockets.
Dimensions W x H x D: With dust cover closed 415 x 118 x 320mm, dust cover open 415 x 365 x 405mm.
Cartridge: Output voltage 5,5mV. Recommended load resistance 47kohms (MM-input).
The manufacturer reserves the right to alter the technical specifications without notice.
The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process.
20
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
Product information
Pro-Ject 1 Xpression III Comfort
Manual turntable with electronic
speed change, automatic
cut-off and fitted cartridge
Ortofon 2M Red
Turntable
Chassis piano-lacquered dark grey
A quiet running AC motor with a two-step metal pulley drives the hub and platter via a flat-ground belt.
The medium density fibre plinth stands on three height-adjustable rubber-damped aluminium cones.
The motor is decoupled from the plinth to reduce vibration transmission.
The resonance-optimised platter is a sandwich construction utilising the hub and an acrylic platter.
The platter's low-tolerance chrome-plated stainless-steel axle runs on a polished ball bearing in a brass
bearing housing.
Electronic speed change for 33 / 45 r.p.m.. Switching to 78 r.p.m. is done manually.
An opto-electronic switch stops the motor as soon as the cartridge has reached the run-out groove.
Connection to the phono input of the amplifier can be made with connecting cables of your taste through the
gold plated phono sockets and earth screw. A standard cable is provided.
External power supply avoids potential electro-mechanical interference.
Tonearm Pro-Ject 8.6c
The turntable is supplied with Ortofon 2M Red-cartridge fitted.
Conical carbon-fibre armtube avoids standing wave reflections.
Low mass aluminium headshell securely glued to armtube.
The inverted bearings consist of four hardened stainless steel points bearing in sapphire cushes.
Flexible counterweight shaft avoids vibration at undesirable frequencies.
Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
The straight armtube with an effective length of 8,6" reduces toe-in error.
Silicone-damped armlift can be adjusted to suit working height of the arm.
The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated
phono sockets.
Dimensions W x H x D: With dust cover closed 415 x 118 x 320mm, dust cover open 415 x 365 x 405mm.
Cartridge: Output voltage 5,5mV. Recommended load resistance 47kohms (MM-input).
The manufacturer reserves the right to alter the technical specifications without notice.
The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process.
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
21
Product information
Pro-Ject 2 Xperience
Manual turntable
Turntable
A quiet running AC motor with a two-step acryl pulley drives the platter's outside edge via a belt.
The transparent acrylic plinth stands on three height-adjustable Sorbothane®-damped aluminium cones.
The motor is decoupled from the plinth to reduce vibration transmission.
The resonance-optimised platter is a sandwich construction utilising the hub, a fine-balanced medium density
fibre platter weighing 2Kg, a 4mm thick flat-ground layer of vinyl and a screw-down metal record clamp.
The platter's low-tolerance chrome-plated stainless-steel axle runs on a Teflon bearing plate in a sintered
bronze bearing housing.
Connection to the phono input of the amplifier can be made with connecting cables of your taste through the
gold plated phono sockets and earth screw. A standard cable is provided.
External power supply avoids potential electro-mechanical interference.
Tonearm Pro-Ject 9c
Conical carbon-fibre armtube avoids standing wave reflections.
Low mass aluminium headshell securely glued to armtube.
The inverted bearings consist of four hardened stainless steel points bearing in sapphire cushes.
Flexible counterweight shaft avoids vibration at undesirable frequencies.
The counterweight supplied is suitable for cartridges weighing between 6 - 9g. Alternative counterweights for
cartridges weighing between 10 - 15g, 9 - 11g or 4 - 6g are available as an accessory part.
Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
The straight armtube with an effective length of 9" reduces toe-in error.
Silicone-damped armlift can be adjusted to suit working height of the arm.
The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated
phono sockets.
Dimensions W x H x D: With dust cover closed 460 x 133 x 360mm, dust cover open 460 x 390 x 460mm.
The manufacturer reserves the right to alter the technical specifications without notice.
22
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
Product information
Pro-Ject 2 Xperience Comfort
Manual turntable with electronic
speed change, automatic cut-off and
fitted cartridge Ortofon 2M Red,
Sumiko Blue Point No. 2 or
Ortofon MC Rondo Red
Turntable
Available finishes
Cherry
Apple
Olive
Wenge
Black gloss
A quiet running AC motor with a two-step acryl pulley drives the platter's outside edge via a belt.
The medium density fibre plinth stands on three height-adjustable Sorbothane®-damped aluminium cones.
The motor is decoupled from the plinth to reduce vibration transmission.
The resonance-optimised platter is a sandwich construction utilising the hub, a fine-balanced medium density
fibre platter weighing 2Kg, a 4mm thick flat-ground layer of vinyl and a screw-down metal record clamp.
The platter's low-tolerance chrome-plated stainless-steel axle runs on a Teflon bearing plate in a sintered
bronze bearing housing.
Electronic speed change for 33 / 45 r.p.m.
An opto-electronic switch stops the motor as soon as the cartridge has reached the run-out groove.
Connection to the phono input of the amplifier can be made with connecting cables of your taste through the
gold plated phono sockets and earth screw. A standard cable is provided.
External power supply avoids potential electro-mechanical interference.
Tonearm Pro-Ject 9c
The turntable is supplied with MM-cartridge Ortofon 2M Red, Sumiko Blue Point No. 2 high output
MC-cartridge or with Ortofon MC Rondo Red low output MC-cartridge cartridge fitted.
Conical carbon-fibre armtube avoids standing wave reflections.
Low mass aluminium headshell securely glued to armtube.
The inverted bearings consist of four hardened stainless steel points bearing in sapphire cushes.
Flexible counterweight shaft avoids vibration at undesirable frequencies.
Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
The straight armtube with an effective length of 9" reduces toe-in error.
Silicone-damped armlift can be adjusted to suit working height of the arm.
The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated
phono sockets.
Dimensions W x H x D: With dust cover closed 460 x 160 x 360mm, dust cover open 460 x 417 x 460mm.
Ortofon 2M Red: Output voltage 5,5mV. Recommended load resistance 47kohms (MM-input).
Sumiko Blue Point No.2: Output voltage 2,5mV. Recommended load resistance 47kohms (MM-input).
Ortofon MC Rondo Red: Output voltage 0,5mV. Recommended load resistance 10 – 200 ohms (MC-input).
The manufacturer reserves the right to alter the technical specifications without notice.
The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process.
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
23
Product information
Pro-Ject 2 Xperience
SuperPack 1 & 2
Manual turntable with fitted cartridge
Ortofon MC Rondo Red or Ortofon MC Salsa
and Pro-Ject Speed Box
Turntable
A quiet running AC motor with a two-step acryl pulley drives the platter's outside edge via a belt.
The transparent acrylic plinth stands on three height-adjustable Sorbothane®-damped aluminium cones.
The motor is decoupled from the plinth to reduce vibration transmission.
The resonance-optimised platter is a sandwich construction utilising the hub, a fine-balanced medium density
fibre platter weighing 2Kg, a 4mm thick flat-ground layer of vinyl and a screw-down metal record clamp.
The platter's low-tolerance chrome-plated stainless-steel axle runs on a Teflon bearing plate in a sintered
bronze bearing housing.
Electronic speed change for 33 / 45 r.p.m.
Connection to the phono input of the amplifier can be made with connecting cables of your taste through the
gold plated phono sockets and earth screw. A standard cable is provided.
External power supply avoids potential electro-mechanical interference.
Tonearm Pro-Ject 9c
SuperPack 1: The turntable is supplied with Ortofon MC Rondo Red low output MC-cartridge fitted.
SuperPack 2: The turntable is supplied with Ortofon MC Salsa low output MC-cartridge fitted.
Conical carbon-fibre armtube avoids standing wave reflections.
Low mass aluminium headshell securely glued to armtube.
The inverted bearings consist of four hardened stainless steel points bearing in sapphire cushes.
Flexible counterweight shaft avoids vibration at undesirable frequencies.
Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
The straight armtube with an effective length of 9" reduces toe-in error.
Silicone-damped armlift can be adjusted to suit working height of the arm.
The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated
phono sockets.
Dimensions W x H x D: With dust cover closed 460 x 133 x 360mm, dust cover open 460 x 390 x 460mm.
SuperPack 1, cartridge: Output voltage 0,30mV. Recommended load resistance > 10 ohms (MC-input).
SuperPack 2, cartridge: Output voltage 0,38mV. Recommended load resistance > 20 ohms (MC-input).
The manufacturer reserves the right to alter the technical specifications without notice.
24
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
Product information
Pro-Ject 6 PerspeX
Manual turntable
Turntable
The transparent acrylic plinth stands on three individually height-adjustable Sorbothane®-damped aluminium
cones and carries the motor and the sub-chassis. The sub-chassis, made of Corian, rests on tree magnetic
fields. A supplied spirit level allows easy adjustment of the sub-chassis.
A quiet running AC motor with a two-step acryl pulley drives the platter's outside edge via a belt.
The inverted bearing uses a stainless-steel axle carrying a ceramic ball on which the ceramic bearing plate runs.
The resonance-optimised platter is a sandwich construction utilising a fine-balanced medium density fibre
platter weighing 2Kg and a 4mm thick flat-ground layer of vinyl and a screw-down metal record clamp.
Connection to the phono input of the amplifier can be made with connecting cables of your taste through the
gold plated phono sockets and earth screw. A standard cable is provided.
External power supply avoids potential electro-mechanical interference.
Tonearm Pro-Ject 9cc Evolution
The headshell and armtube are fashioned from a single piece of carbon-fibre.
Conical armtube avoids standing wave reflections.
Inverted tonearm bearing comprises four hardened stainless tips in ABEC7 spec ballraces.
Rings provide very solid arm bearing housings. The massive outside ring is open to avoid resonances.
Sorbothane®-damped counterweight effectively counteracts unwanted resonances.
The counterweights supplied are suitable for cartridges weighing between 5 - 7,5g, 7 - 10g, 9 - 11g or
10 - 14g.
Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing
warped records.
Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
The straight armtube with an effective length of 9" reduces toe-in error.
Silicone-damped armlift can be adjusted to suit working height of the arm.
The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated
phono sockets.
High quality connection cable Pro-Ject Connect it Phono RCA-C supplied (123cm)
Dimensions W x H x D: With dust cover closed 460 x 160 x 365mm, dust cover open 460 x 420 x 465mm.
The manufacturer reserves the right to alter the technical specifications without notice.
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
25
Product information
Pro-Ject 6 PerspeX SuperPack
Manual turntable with fitted cartridge
Ortofon MC Valencia and Pro-Ject connection
cable Connect it Phono RCA-C
Turntable
The transparent acrylic plinth stands on three individually height-adjustable Sorbothane®-damped aluminium
cones and carries the motor and the sub-chassis. The sub-chassis, made of Corian, rests on tree magnetic
fields. A supplied spirit level allows easy adjustment of the sub-chassis.
A quiet running AC motor with a two-step acryl pulley drives the platter's outside edge via a belt.
The inverted bearing uses a stainless-steel axle carrying a ceramic ball on which the ceramic bearing plate runs.
The resonance-optimised platter is a sandwich construction utilising a fine-balanced medium density fibre
platter weighing 2Kg and a 4mm thick flat-ground layer of vinyl and a screw-down metal record clamp.
Connection to the phono input of the amplifier can be made with connecting cables of your taste through the
gold plated phono sockets and earth screw. A standard cable is provided.
External power supply avoids potential electro-mechanical interference.
Tonearm Pro-Ject 9cc Evolution
The turntable is supplied with Ortofon MC Valencia low output MC-cartridge fitted.
The headshell and armtube are fashioned from a single piece of carbon-fibre.
Conical armtube avoids standing wave reflections.
Inverted tonearm bearing comprises four hardened stainless tips in ABEC7 spec ballraces.
Rings provide very solid arm bearing housings. The massive outside ring is open to avoid resonances.
Sorbothane®-damped counterweight effectively counteracts unwanted resonances.
The counterweights supplied are suitable for cartridges weighing between 5 - 7,5g, 7 - 10g, 9 - 11g or
10 - 14g.
Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing
warped records.
Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
The straight armtube with an effective length of 9" reduces toe-in error.
Silicone-damped armlift can be adjusted to suit working height of the arm.
The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated
phono sockets.
Dimensions W x H x D: With dust cover closed 460 x 160 x 365mm, dust cover open 460 x 420 x 465mm.
Cartridge: Output voltage 0,45mV. Recommended load resistance 100 ohms (MC-input).
The manufacturer reserves the right to alter the technical specifications without notice.
26
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
Produktinformation
Pro-Ject Xtension
Manual turntable with
9" or 12" Pro-Ject Evolution tonearm
and build in Pro-Ject Speed Box SE
(Picture shows Xtension/12cc Evolution)
Turntable
Available finishes
Cherry
Apple
Olive
Black gloss
A quiet running AC motor with a two-step metal pulley drives the platter's outside edge via a belt.
Electronic speed change between 33 and 45 r.p.m.. Switching to 78 r.p.m. is done manually.
The medium density fibre plinth rests on four individually height-adjustable magnetic field feet. A build in spirit
level allows easy adjustment of the chassis.
The resonance-optimised platter is a sandwich construction utilising a fine-balanced and damped aluminium
platter weighing 5,7kg and a 4mm thick flat-ground layer of vinyl and a brass record puck.
The magnet supported, inverted bearing uses a stainless-steel axle carrying a ceramic ball on which the ceramic
bearing plate runs.
Central metal block optimises centre of gravity and damps main bearing.
External power supply avoids potential electro-mechanical interference.
Tonearms Pro-Ject 9cc Evolution and 12cc Evolution
The headshell and armtube are fashioned from a single piece of carbon-fibre.
Conical armtube avoids standing wave reflections.
Inverted bearing design with four ABEC7 spec ballraces.
Arm bearing housing of solid ring type. The massive outside ring is open to avoid resonances.
Sorbothane®-damped counterweight effectively counteracts unwanted resonances.
Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
Modell X tension / 9cc Evolution with dynamic balanced 9" tonearm Pro-Ject 9cc Evolution
Modell X tension / 12cc Evolution with dynamic balanced 12" tonearm Pro-Ject 12cc Evolution
Modell X tension / without tonearm. Arm board for 9" and 12" tonearms
Dimensions W x H x D: With dust cover closed 550 x 250 x 450mm, dust cover open 550 x 550 x 560mm.
The manufacturer reserves the right to alter the technical specifications without notice.
The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process.
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
27
Produktinformation
Pro-Ject Xtension
Manual turntable with
static or dynamic balanced
9" or 12" Ortofon tonearm and
build in Pro-Ject Speed Box SE
(Picture shows Xtension/RS-309D)
Turntable
Available finishes
Cherry
Apple
Olive
Black gloss
A quiet running AC motor with a two-step metal pulley drives the platter's outside edge via a belt.
Electronic speed change between 33 and 45 r.p.m.. Switching to 78 r.p.m. is done manually.
The medium density fibre plinth rests on four individually height-adjustable magnetic field feet. A build in spirit
level allows easy adjustment of the chassis.
The resonance-optimised platter is a sandwich construction utilising a fine-balanced and damped aluminium
platter weighing 5,7kg and a 4mm thick flat-ground layer of vinyl and a brass record puck.
The magnet supported, inverted bearing uses a stainless-steel axle carrying a ceramic ball on which the ceramic
bearing plate runs.
Central metal block optimises centre of gravity and damps main bearing.
External power supply avoids potential electro-mechanical interference.
Tonearms
Modell X tension / AS-212S with static balanced 9" tonearm Ortofon AS-212S
Modell X tension / AS-309S with static balanced 12" tonearm Ortofon AS-309S
Modell X tension / AS-212D with dynamic balanced 9" tonearm Ortofon RS-212D
Modell X tension / AS-309D with dynamic balanced 12" tonearm Ortofon RS-309D
Modell X tension / without tonearm. Arm board for 9" and 12" tonearms
Dimensions W x H x D: With dust cover closed 550 x 250 x 450mm, dust cover open 550 x 550 x 560mm.
The manufacturer reserves the right to alter the technical specifications without notice.
The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process.
28
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
Product information
Pro-Ject RPM 1 Genie
Manual turntable with fitted cartridge
Ortofon OM 3E
Turntable
Chassis available in matt black
A quiet running synchronous motor with a two-step metal pulley drives the platter's outside edge via a
rubber belt.
The drive motor is isolated on its own platform and completely decoupled from the plinth to eliminate
vibration transmission.
The resonance-optimised platter is made of medium density fibre.
A inverted, chrome-plated stainless-steel axle runs on a polished metal ball in a sintered bronze bearing
housing.
Connection to the phono input of the amplifier can be made with connecting cables of your taste through
the gold plated phono sockets and earth screw.
External power supply avoids potential electro-mechanical interference.
Tonearm Pro-Ject 8.6s
The turntable is supplied with Ortofon OM 3E MM-cartridge fitted.
The headshell and armtube are fashioned from a single piece of aluminium.
The horizontal bearings consist of two hardened stainless steel points and ballraces.
Eccentrically mounted counterweight reduces cantilever forces and dynamic wow when playing
warped records.
Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
The S-shaped armtube with an effective length of 8,6" reduces toe-in error.
The internal wiring consists of silver coated, high-purity copper.
Dimensions W x H x D: 380 x 115 x 350mm
Cartridge: Output voltage 4mV. Recommended load resistance 47kohms (MM-input).
The manufacturer reserves the right to alter the technical specifications without notice.
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
29
Product information
Pro-Ject RPM 5
Manual turntable with fitted cartridge
Ortofon 2M Red
Turntable
Chassis piano-lacquered dark grey
A quiet running AC motor with a two-step metal pulley drives the hub and platter via a flat-ground belt.
The medium density fibre plinth stands on three height-adjustable rubber-damped aluminium cones.
The motor is decoupled from the plinth to reduce vibration transmission.
The resonance-optimised platter is a sandwich construction utilising the hub, an medium density fibre
platter, a cork mat (a standard felt mat is also supplied) and a screw-down record clamp.
The platter's low-tolerance chrome-plated stainless-steel axle runs on a Teflon bearing plate in a sintered
bronze bearing housing.
Central metal block optimises centre of gravity and damps main bearing.
Connection to the phono input of the amplifier can be made with connecting cables of your taste through the
gold plated phono sockets and earth screw. A standard cable is provided.
External power supply avoids potential electro-mechanical interference.
Tonearm Pro-Ject 9c
The turntable is supplied with Ortofon 2M Red-cartridge fitted.
Conical carbon-fibre armtube avoids standing wave reflections.
Low mass aluminium headshell securely glued to armtube.
The inverted bearings consist of four hardened stainless steel points bearing in sapphire cushes.
Rings provide very solid arm bearing housings. The outside ring is open to avoid resonances.
Design of counterweight effectively counteracts unwanted resonances.
Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing
warped records.
Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
The straight armtube with an effective length of 9" reduces toe-in error.
Silicone-damped armlift can be adjusted to suit working height of the arm.
The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated
phono sockets.
Dimensions W x H x D: 371 x 145 x 300mm. Dust cover Cover it optional. W x H x D: 525 x 290 x 425mm.
Cartridge: Output voltage 5,5mV. Recommended load resistance 47kohms (MM-input).
The manufacturer reserves the right to alter the technical specifications without notice.
The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process.
30
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
Product information
Pro-Ject RPM 5 SuperPack
Manual turntable with electronic speed change
and fitted cartridge Pro-Ject Pick it MC1H
Turntable
Chassis piano-lacquered dark grey
A quiet running AC motor with a two-step metal pulley drives the hub and platter via a flat-ground belt.
The medium density fibre plinth stands on three height-adjustable rubber-damped aluminium cones.
The motor is decoupled from the plinth to reduce vibration transmission.
The resonance-optimised platter is a sandwich construction utilising the hub, an medium density fibre
platter, a cork mat (a standard felt mat is also supplied) and a screw-down record clamp.
The platter's low-tolerance chrome-plated stainless-steel axle runs on a Teflon bearing plate in a sintered
bronze bearing housing.
Central metal block optimises centre of gravity and damps main bearing.
Electronic speed change for 33 / 45 r.p.m.. Switching to 78 r.p.m. is done manually.
Connection to the phono input of the amplifier can be made with connecting cables of your taste through the
gold plated phono sockets and earth screw. A standard cable is provided.
External power supply avoids potential electro-mechanical interference.
Tonearm Pro-Ject 9c
The turntable is supplied with Pro-Ject Pick it MC1H high output MC-cartridge fitted.
Conical carbon-fibre armtube avoids standing wave reflections.
Low mass aluminium headshell securely glued to armtube.
The inverted bearings consist of four hardened stainless steel points bearing in sapphire cushes.
Rings provide very solid arm bearing housings. The outside ring is open to avoid resonances.
Design of counterweight effectively counteracts unwanted resonances.
Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing
warped records.
Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
The straight armtube with an effective length of 9" reduces toe-in error.
Silicone-damped armlift can be adjusted to suit working height of the arm.
The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated
phono sockets.
Dimensions W x H x D: 371 x 145 x 300mm. Dust cover Cover it optional. W x H x D: 525 x 290 x 425mm.
Cartridge: Output voltage 2,2mV. Recommended load resistance 47kohms (MM-input).
The manufacturer reserves the right to alter the technical specifications without notice.
The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process.
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
31
Product information
Pro-Ject RPM 6.1 SB
Manual turntable with
electronic speed change
Turntable
A quiet running AC motor with a two-step metal pulley drives the acrylic hub and platter via a flat-ground belt.
The medium density fibre plinth stands on three height-adjustable Sorbothane®-damped aluminium cones.
The motor is decoupled from the plinth to reduce vibration transmission.
The resonance-optimised platter is a sandwich construction utilising the hub, an medium density fibre
platter, a 4mm thick flat-ground layer of vinyl and a brass record puck.
The inverted bearing uses a stainless-steel axle carrying a ceramic ball on which the ceramic bearing plate runs.
Electronic speed change for 33 / 45 r.p.m.. Switching to 78 r.p.m. is done manually.
Central metal block optimises centre of gravity and damps main bearing.
Connection to the phono input of the amplifier can be made with connecting cables of your taste through the
gold plated phono sockets and earth screw. A standard cable is provided.
External power supply avoids potential electro-mechanical interference.
Tonearm Pro-Ject 9c
Conical carbon-fibre armtube avoids standing wave reflections.
Low mass aluminium headshell securely glued to armtube.
The inverted bearings consist of four hardened stainless steel points bearing in sapphire cushes.
Rings provide very solid arm bearing housings. The outside ring is open to avoid resonances.
Design of counterweight effectively counteracts unwanted resonances.
The counterweight supplied is suitable for cartridges weighing between 6 - 10g. Alternative counterweights for
cartridges weighing between 10 - 15g, 9 - 11g or 4 - 6g are available as an accessory part.
Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing
warped records.
Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
The straight armtube with an effective length of 9" reduces toe-in error.
Silicone-damped armlift can be adjusted to suit working height of the arm.
The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated
phono sockets.
Dimensions W x H x D: 385 x 170 x 330mm. Dust cover Cover it optional. W x H x D: 525 x 290 x 425mm.
The manufacturer reserves the right to alter the technical specifications without notice.
32
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
Product information
Pro-Ject RPM 6.1 SB SuperPack
Manual turntable with electronic
speed change, and fitted cartridge
Ortofon MC Samba
Turntable
A quiet running AC motor with a two-step metal pulley drives the acrylic hub and platter via a flat-ground belt.
The medium density fibre plinth stands on three height-adjustable Sorbothane®-damped aluminium cones.
The motor is decoupled from the plinth to reduce vibration transmission.
The resonance-optimised platter is a sandwich construction utilising the hub, an medium density fibre
platter, a 4mm thick flat-ground layer of vinyl and a brass record puck.
The inverted bearing uses a stainless-steel axle carrying a ceramic ball on which the ceramic bearing plate runs.
Electronic speed change for 33 / 45 r.p.m.. Switching to 78 r.p.m. is done manually.
Central metal block optimises centre of gravity and damps main bearing.
Connection to the phono input of the amplifier can be made with connecting cables of your taste through the
gold plated phono sockets and earth screw. A standard cable is provided.
External power supply avoids potential electro-mechanical interference.
Tonearm Pro-Ject 9c
The turntable is supplied with Ortofon MC Samba low output MC-cartridge fitted.
Conical carbon-fibre armtube avoids standing wave reflections.
Low mass aluminium headshell securely glued to armtube.
The inverted bearings consist of four hardened stainless steel points bearing in sapphire cushes.
Rings provide very solid arm bearing housings. The outside ring is open to avoid resonances.
Design of counterweight effectively counteracts unwanted resonances.
Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing
warped records.
Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
The straight armtube with an effective length of 9" reduces toe-in error.
Silicone-damped armlift can be adjusted to suit working height of the arm.
The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated
phono sockets.
Dimensions W x H x D: 385 x 170 x 330mm. Dust cover Cover it optional. W x H x D: 525 x 290 x 425mm.
Cartridge: Output voltage 0,30mV. Recommended load resistance > 10 ohms (MC-input).
The manufacturer reserves the right to alter the technical specifications without notice.
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
33
Product information
Pro-Ject RPM 9.1
Manual turntable
Turntable
Chassis and motor housing piano-lacquered dark grey
A quiet running AC motor with a two-step acryl pulley drives the platter's outside edge via a belt.
The medium density fibre plinth stands on three height-adjustable Sorbothane®-damped aluminium cones.
A supplied spirit level allows easy adjustment. Granulate filled plinth guarantees constant damping.
The motor is mounted in a separate metal housing to eliminate vibration transmission.
The resonance-optimised platter is a sandwich construction utilising an acrylic platter weighing 3,5Kg
and a brass record puck.
The inverted bearing uses a stainless-steel axle carrying a ceramic ball on which the ceramic bearing plate runs.
Central metal block optimises centre of gravity and damps main bearing.
Connection to the phono input of the amplifier can be made with connecting cables of your taste through
the gold plated phono sockets and earth screw. A standard cable is provided.
External power supply avoids potential electro-mechanical interference.
Tonearm Pro-Ject 9cc
The headshell and armtube are fashioned from a single piece of carbon-fibre.
Conical armtube avoids standing wave reflections.
Inverted tonearm bearing comprises four hardened stainless tips in ABEC7 spec ballraces.
Rings provide very solid arm bearing housings. The outside ring is open to avoid resonances.
Design of counterweight effectively counteracts unwanted resonances.
The counterweight supplied is suitable for cartridges weighing between 6 - 10g. Alternative counterweights for
cartridges weighing between 8 - 11g and 11 - 15g are available as an accessory part.
The counterweight supplied is suitable for cartridges weighing between 6 - 10g. Alternative counterweights for
cartridges weighing between 11 - 15g, 8 - 11g or 5 - 8g are available as an accessory part.
Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing
warped records.
Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
The straight armtube with an effective length of 9" reduces toe-in error.
Silicone-damped armlift can be adjusted to suit working height of the arm.
The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated
phono sockets.
Dimensions W x H x D: Including motor unit 440 x 180 x 325mm.
Dust cover Cover it optional. W x H x D: 525 x 290 x 425mm.
The manufacturer reserves the right to alter the technical specifications without notice.
The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process.
34
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
Product information
Pro-Ject RPM 9.1 SuperPack 1 & 2
Manual turntable with fitted cartridge
Ortofon MC Rondo Red or Sumiko Blue Point No. 2
and Pro-Ject Speed Box SE
Turntable
Chassis and motor housing piano-lacquered dark grey
A quiet running AC motor with a two-step acryl pulley drives the platter's outside edge via a belt.
The medium density fibre plinth stands on three height-adjustable Sorbothane®-damped aluminium cones.
A supplied spirit level allows easy adjustment. Granulate filled plinth guarantees constant damping.
The motor is mounted in a separate metal housing to eliminate vibration transmission.
The resonance-optimised platter is a sandwich construction utilising an acrylic platter weighing 3,5Kg
and a brass record puck.
The inverted bearing uses a stainless-steel axle carrying a ceramic ball on which the ceramic bearing plate runs.
Central metal block optimises centre of gravity and damps main bearing.
Connection to the phono input of the amplifier can be made with connecting cables of your taste through
the gold plated phono sockets and earth screw. A standard cable is provided.
External power supply avoids potential electro-mechanical interference.
Tonearm Pro-Ject 9cc
SuperPack 1: The turntable is supplied with Ortofon MC Rondo Red low output MC-cartridge fitted.
SuperPack 2: The turntable is supplied with Sumiko Blue Point No. 2 high output MC-cartridge fitted.
The headshell and armtube are fashioned from a single piece of carbon-fibre.
Conical armtube avoids standing wave reflections.
Inverted tonearm bearing comprises four hardened stainless tips in ABEC7 spec ballraces.
Rings provide very solid arm bearing housings. The outside ring is open to avoid resonances.
Design of counterweight effectively counteracts unwanted resonances.
Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing
warped records.
Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
The straight armtube with an effective length of 9" reduces toe-in error.
Silicone-damped armlift can be adjusted to suit working height of the arm.
The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated
phono sockets.
Dimensions W x H x D: Including motor unit 440 x 180 x 325mm.
Dust cover Cover it optional. W x H x D: 525 x 290 x 425mm.
SuperPack 1, cartridge: Output voltage 0,30mV. Recommended load resistance > 10 ohms (MC-input).
SuperPack 2, cartridge: Output voltage 2,5mV. Recommended load resistance 47kohms (MM-input).
The manufacturer reserves the right to alter the technical specifications without notice.
The colours in the picture may differ slightly from the actual article due to inaccuracies in the printing process.
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
35
Product information
Pro-Ject RPM 9.1X
Manual turntable
Turntable
A quiet running AC motor with a two-step acryl pulley drives the platter's outside edge via a belt.
The transparent acrylic plinth stands on three height-adjustable Sorbothane®-damped aluminium cones.
A supplied spirit level allows easy adjustment.
The motor is mounted in a separate metal housing to eliminate vibration transmission.
The resonance-optimised platter is a sandwich construction utilising an acrylic platter weighing 3,5Kg
and a brass record puck.
The inverted bearing uses a stainless-steel axle carrying a ceramic ball on which the ceramic bearing plate runs.
Central metal block optimises centre of gravity and damps main bearing.
Connection to the phono input of the amplifier can be made with connecting cables of your taste through
the gold plated phono sockets and earth screw. A standard cable is provided.
External power supply avoids potential electro-mechanical interference.
Tonearm Pro-Ject 9cc
The headshell and armtube are fashioned from a single piece of carbon-fibre.
Conical armtube avoids standing wave reflections.
Inverted tonearm bearing comprises four hardened stainless tips in ABEC7 spec ballraces.
Rings provide very solid arm bearing housings. The outside ring is open to avoid resonances.
Design of counterweight effectively counteracts unwanted resonances.
The counterweight supplied is suitable for cartridges weighing between 6 - 10g. Alternative counterweights for
cartridges weighing between 11 - 15g, 8 - 11g or 5 - 8g are available as an accessory part.
Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing
warped records.
Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
The straight armtube with an effective length of 9" reduces toe-in error.
Silicone-damped armlift can be adjusted to suit working height of the arm.
The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated
phono sockets.
Dimensions W x H x D: Including motor unit 440 x 180 x 325mm.
Dust cover Cover it optional. W x H x D: 525 x 290 x 425mm.
The manufacturer reserves the right to alter the technical specifications without notice.
36
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
Product information
Pro-Ject RPM 10
Manual turntable with
10" tonearm and
equipment base
Pro-Ject Ground it deluxe 1
Turntable
Chassis, motor housing and granulate filled equipment base Ground it deluxe piano-lacquered dark grey
A quiet running AC motor with a two-step acryl pulley drives the platter's outside edge via a belt.
The medium density fibre plinth stands on three height-adjustable Sorbothane®-damped aluminium cones.
Granulate filled plinth guarantees constant damping. A supplied spirit level allows easy adjustment.
The motor is mounted in a separate metal housing to eliminate vibration transmission.
The resonance-optimised platter is a sandwich construction utilising an acrylic platter weighing 5,4Kg
and a brass record puck.
The magnet supported, inverted bearing uses a stainless-steel axle carrying a ceramic ball on which the ceramic
bearing plate runs.
Central metal block optimises centre of gravity and damps main bearing.
Connection to the phono input of the amplifier can be made with connecting cables of your taste through
the gold plated phono sockets and earth screw. A standard cable is provided.
External power supply avoids potential electro-mechanical interference.
Tonearm Pro-Ject 10cc
The headshell and armtube are fashioned from a single piece of carbon-fibre.
Conical armtube avoids standing wave reflections.
Inverted tonearm bearing comprises four hardened stainless tips in ABEC7 spec ballraces.
Rings provide very solid arm bearing housings. The outside ring is open to avoid resonances.
Design of counterweight effectively counteracts unwanted resonances.
The counterweight supplied is suitable for cartridges weighing between 6 - 9g. Alternative counterweights for
cartridges weighing between 10 - 15g or 7 - 11g are available as an accessory part.
Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing
warped records.
Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).
Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.
The straight armtube with an effective length of 10" reduces toe-in error.
Silicone-damped armlift can be adjusted to suit working height of the arm.
The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated
phono sockets.
Dimensions turntable, W x H x D: Including motor unit 480 x 210 x 330mm.
Dimensions equipment base Ground it deluxe: 500 x 65 x 400mm (H including feet). H without cone feet 45mm
Dust cover Cover it optional, W x H x D: 525 x 290 x 425mm.
The manufacturer reserves the right to alter the technical specifications without notice.
Pro-Ject Audio Systems is a registered trademark of Heinz Lichtenegger
1050 Vienna · Margareten Road 98 · Tel. +43(0)15448580 · Fax. +43(0)15456697
www.project-audio.com · © Heinz Lichtenegger · Revision 27.1.09
37
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising