Typhoon 1610P/1612 (Nobles Wet/Dry Vacuum)

Typhoon 1610P/1612 (Nobles Wet/Dry Vacuum)
Typhoon
1610P/1612
Wet/Dry Vacuum
Model No.:
608240 – 1610P
608239 – 1612
Operator and Parts Manual
CleaningPartsDirect.com
662-393-3045
NOBLES
12875 RANSOM STREET
HOLLAND MI 49424 U.S.A.
CUSTOMER SERVICE: 1-800-365-6625
FAX: 1–800–678–4240
OUTSIDE U.S. : 1-616-786-2330
Home
608612
Rev. 01 (01-00)
Find...
Go To..
OPERATION
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed,
including the following:
READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE)
WARNING -To reduce the risk of fire, electric shock, or injury:
1.
Do not leave appliance when plugged in. Unplug from outlet when not in use and before
servicing.
2.
Use indoors only. Always install float before any wet pick–up operation.
3.
Do not allow to be used as a toy. Close attention is necessary when used by or near
children.
4.
Use only as described in this manual. Use only manufacturer’s recommended attachments.
5.
Do not use with damaged cord or plug. If appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped into water, return it to a service center.
6.
Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord
around sharp edges or corners. Do not run appliance over cord. Keep cord away from
heated surfaces.
7.
Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
8.
Do not handle plug or appliance with wet hands.
9
Do not put any object into openings. Do not use with any opening blocked; keep free of
dust, lint, hair, and anything that may reduce air flow.
10. Keep hair, loose clothing, fingers, and all parts of body away from openings and moving
parts.
11. Turn off all controls before unplugging.
12. Use extra care when cleaning on stairs.
13. Do not use to pick up flammable or combustible liquids such as gasoline or use in areas
where they may be present.
14. Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.
2
Home
Find...
Go To..
Typhoon 1610P/1612 (01–00)
OPERATION
INSTRUCTIONS DE SÉCURITÉ
LIRE TOUTES LES INSTRUCTIONS AVANT DE FAIRE FONCTIONNER (CET APPAREIL)
ADVERTISSEMENT - Pour réduire les risques d’incendie, de choc électrique ou de blessure:
1.
Ne pas laisser l’appareil san surveillance lorsqu’il est branché. Débrancher lorsque
l’appareil n’est pas utilisé et evant l’entretien.
2.
Utiliser á l’intererieur seulement. Installer un flotteur avant d’aspirer des matières humides.
3.
Ne pas permettre aux enfants de jouer avec l’appareil. une attention particuliér est
nécessarie lorsque lappareil est utilisé par des enfants ou à proximite de ces deniers.
4.
Nutiliser que conformément à cette notice avec les accessories recommandés par le
fabricant.
5.
Ne pas utiliser si le cordon ou la fiche est endommagé. Retourner lappareil a un atelier
de réparation s’il ne fonctionne pas bien, s’il est tombé ou s’il a été endommage, oublie
à l’extérieur ou immergé.
6.
Ne pas tirer soulever ou traîner l’appareil par le condon. Ne pas uliliser le cordon
comme une poignée, le coincer dans l’embrasure d’une porte ou l’appuyer contre des
arêtes vives ou des coins. Ne pas faire rouler l’appareil sur le cordon. Garder le cordon à
l’écart des surfaces chaudes.
7.
Ne pas débracher en tirant sur le cordon. Tier plutôt la fiche.
8.
Ne pas toucher la fiche ou l’appareil lorsque vos mains sont humides.
9.
N’insérer aucun objet dans les ouvertures. Ne pas utiliser l’appareil losqu’une ouverture
est bloquée. S’assurer que de la poussière, de la peluche, des cheveuxou d’autres
matières ne réduisent pas le débit d’air.
10. Maintenir les cheveux, les vêtements amples, les doigts et toutes les parties du corps l’écart
des ouvertures et des piéces mobiles
11. Mettre toutes les commandes a’la postion ARRêT avant de de’brancher l’appareil.
12. User de prudence lors du nettoyage des escaliers.
13. Ne pas aspirer des liquides inflammables ou combustibles, comme de l’essence, et ne
pas faire fonctionner dans des endroits où peuvente se trouver de tels liquides.
14. Ne pas aspirer de matières en combustion ou qui dégagent de la furmée, comme des cigarettes,
des allumettes ou des dendres chaudes.
Typhoon 1610P/1612 (01–00)
Home
Find...
Go To..
3
OPERATION
GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should malfunction or breakdown, grounding provides a
path of least resistance for electric current to reduce the risk of electric shock. This appliance is
equipped with a cord having an equipment–grounding conductor and grounding plug. The plug
must be plugged into an appropriate outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
WARNING – Improper connection of the equipment–grounding conductor can result
in a risk of electric shock. Check with a qualified electrician or service person if you are in
doubt as to whether the outlet is properly grounded. Do not modify the plug provided with
the appliance – if it will not fit the outlet, have a proper outlet installed by a qualified
electrician.
This appliance is for use on a nominal 120–volt circuit and has a grounding attachment plug that
looks like the plug illustrated in sketch. Make sure that the appliance is connected to an outlet
having the same configuration as the plug. No adaptor should be used with this appliance.
GROUNDED OUTLET
(3 HOLE)
GROUNDING PIN
INSTRUCTIONS VISANT LA MISE ‘A LA TERRE
Cet appareil doit être mis à la terre. En cas de défaillance ou de panne éventuelles, la mise à la
terre fournit au courant un chemin de moindre résistance qui réduit le risque de choc électrique.
Cet appareil est pourvu d’un cordon muni d’un conducteur de terre et d’une fiche avec broche de
terre. La fiche doit être branchée dans une prise appropriée correctement installée et mise à la
terre conformément aux règlements et ordonnances municipaux.
AVERTISSEMENT. Un conducteur de terre mal raccordé peut entraîner un risque de choc
électrique. Consulter un électricien ou un technicien d’entretien qualifié si vous n’êtes
pas certain que la prise est correctement mise à la terre. Ne pas modifier la fiche fournie
avec l’appareil – si elle ne peut être insérée dans la prise, faire installer une prise adéquate
par un électricien qualifié.
Cet appareil est destiné à un circuit de 120 v et est muni d’une fiche de mise à la terre semblable à
celle illustrée par le croquis. S’assurer que l’appareil est branché à une prise de courant ayant la même
configuration que la fiche. Aucun adaptateur ne devrait être utilisé avec cet appareil.
4
Home
Find...
Go To..
Typhoon 1610P/1612 (01–00)
OPERATION
This manual is furnished with each new model. It
provides necessary operation, machine maintenance
instructions and an illustrated parts list.
MACHINE DATA
Read this manual completely and understand the
machine before operating or servicing.
Please fill out at time of installation for future reference.
This machine will provide excellent service. However,
the best results will be obtained at minimum costs if:
Model No.Install. Date -
The machine is operated with reasonable care.
The machine is maintained regularly - per the
Serial No.-
1999 Tennant Company
machine care instructions provided.
The machine is maintained with manufacturer
supplied or equivalent parts.
Printed in U.S.A
Nobles is a registered United States trademark of Tennant Company.
Typhoon is a United States trademark of Tennant Company.
TABLE OF CONTENTS
SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . 6
STORING MACHINE . . . . . . . . . . . . . . . . . . . . 11
MACHINE INSTALLATION . . . . . . . . . . . . . . . 7
TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . 12
MACHINE SETUP . . . . . . . . . . . . . . . . . . . . . . . . 8
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . 13
MACHINE OPERATION . . . . . . . . . . . . . . . . . . 9
PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
DRAINING RECOVERY TANK . . . . . . . . . . . 10
OPTIONAL ACCESSORIES . . . . . . . . . . . . . 20
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . 11
Typhoon 1610P/1612 (04–99)
Home
Find...
Go To..
5
OPERATION
SAFETY PRECAUTIONS
4. Before leaving or servicing machine:
– Turn off machine.
– Unplug cord from wall outlet.
This machine is intended for commercial use. It is
suited for wet/dry vacuuming in an indoor environment
and is not constructed for any other use. Use only
recommended accessory tools.
5. When servicing machine:
– Unplug cord from wall outlet.
– Use manufacturer supplied or approved
replacement parts.
The following safety alert symbols are used throughout
this manual as indicated in their description.
WARNING: To warn of hazards or unsafe
practices which could result in severe personal
injury or death.
WARNING: Hazardous Voltage. Shock or
electrocution can result. Unplug machine before
servicing.
FOR SAFETY: To identify actions which must be
followed for safe operation of equipment.
WARNING: Flammable materials or reactive
metals can cause an explosion or fire. Do not pick
up.
The following information signals potentially dangerous
conditions to the operator or equipment:
GROUNDING INSTRUCTIONS
FOR SAFETY:
1. Do not operate machine:
– Unless trained and authorized.
– Unless operator manual is read and
understood.
– In flammable or explosive areas unless
designed for use in those areas.
– With damaged cord or plug.
– If not in proper operating condition.
– In outdoor areas.
– In standing water.
– Without bag and/or filters in place.
– With the use of additional extension cords.
Only use manufacturer’s extension cord
equipped with machine which has proper
capacity and is grounded.
Machine must be grounded. If it should
malfunction or breakdown, grounding provides a
path of least resistance for electrical current to
reduce the risk of electrical shock. This machine
is equipped with a cord having an
equipment–grounding conductor and grounding
plug. The plug must be plugged into an
appropriate outlet that is properly installed in
accordance with all local codes and ordinances.
Do not remove ground pin; if missing, replace
plug before use.
GROUNDED OUTLET
(3 HOLE)
2. Before operating machine:
– Make sure all safety devices are in place
and operate properly.
GROUNDING PIN
3. When using machine:
– Do not run machine over cord.
– Do not pull machine by plug or cord.
– Do not pull cord around sharp edges or
corners.
– Do not unplug by pulling on cord.
– Do not stretch cord.
– Do not handle plug with wet hands.
– Keep cord away from heated surfaces.
– Do not pick up burning or smoking debris,
such as cigarettes, matches or hot ashes.
– Report machine damage or faulty
operation immediately.
6
Home
Find...
Go To..
Typhoon 1610P/1612 (11–99)
OPERATION
ATTACHING OPTIONAL SQUEEGEE KIT
MACHINE INSTALLATION
See Optional Accessories.
Check carton for signs of damage. Report damages
to carrier immediately.
1. Empty recovery tank.
Check machine contents list, contact distributor for
missing items.
3. Tip machine on back.
MACHINE CONTENTS
5. Install squeegee mounting bracket with bolts and
washers (Figure 2).
2. Remove vacuum bag.
4. Remove (2) bolts and washers located at bottom
of machine.
1 – 3 m (10 ft) vacuum hose – For accessory tools
1 – Cloth bag
1 – Paper bag
1 – 15 m (50 ft) power cord
NOTE: Squeegee and Accessory Tool Kits are sold
separately. See Optional Accessories.
ATTACHING HANDLE
1. Remove handle from ship position. Also remove
upper handle mounting screws and washers from
machine (Figure 1).
FIG. 2
6. Fasten squeegee to mounting bracket. Use (2)
clevis and cotter pins provided (Figure 3).
Handle
(4) Screws
w/Washers
Cord Grip
FIG. 3
Exhaust Hose
7. Stand vacuum upright.
FIG. 1
2. Realign handle as shown and replace screws and
washers.
3. Push excess cord slack up into cord grip. Tighten
cord grip with 5/16 inch wrench until cord is
secure. DO NOT overtighten.
8. Insert spacer through hole in pedal as shown.
Position pedal between two holes in bracket and
slide hex head screw through bracket and pedal.
Secure with washer and nut (Figure 4).
4. Connect exhaust hose to bottom of handle
housing.
FIG. 4
Typhoon 1610P/1612 (04–99)
Home
Find...
Go To..
7
OPERATION
9. Slide pedal between two mounting arms on back
of machine. Align and insert clevis pin through
arms and slot in pedal, secure with cotter pin
(Figure 5).
MACHINE SETUP
1. Connect 15m (50 ft) power cord to machine pigtail
cord.
2. Plug power cord into a grounded outlet (Figure 8).
Grounded
Outlet
Grounded
3 Hole Outlet
Grounding
Edge/hole
Ground Pin
(120V)
(230V)
FIG. 8
FIG. 5
10. Attach squeegee assembly to bracket. Use (2)
thumb screws to secure (Figure 6).
FOR SAFETY: Do not operate machine with the
use of additional extension cords. Only use
manufacturer’s extension cord equipped with
machine which has proper capacity and is
grounded.
WET VACUUMING
1. Open machine cover and remove vacuum bag
from recovery tank (Figure 9).
FIG. 6
11. Connect 840mm (33 in) vacuum hose to
squeegee assembly and to neck on machine lid
(Figure 7).
FIG. 9
2. Make sure automatic float shut-off screen is in
place (Figure10).
FIG. 7
FIG. 10
8
Home
Find...
Go To..
Typhoon 1610P/1612 (11–99)
OPERATION
ATTENTION: To prevent vacuum motor damage,
automatic float shut-off screen must be in place.
DRY VACUUMING
1. Open vacuum machine cover and install cloth filter
bag, make sure that the bag edge is properly
seated on compartment rim (Figure 11).
For easy debris disposal and to prolong cloth bag
life, use a paper vacuum bag inside the cloth bag.
Tuck the top of paper bag around outside rim of
cloth bag. Never use paper bag without cloth filter
bag in place. Do not reuse paper bags – always
dispose (Figure 11).
FIG. 12
3. Activate ON/OFF switch and operate accessory
tool as normal.
4. During DRY vacuuming, check bag periodically for
fullness. For best suction performance, empty bag
at 3/4 full.
During WET vacuuming, the float shut-off screen
will automatically stop water intake when recovery
tank becomes full (See DRAINING RECOVERY
TANK).
ATTENTION: If foam develops in recovery tank
during wet vacuuming, use a quality defoamer
chemical to eliminate the foam. Foam buildup will
NOT activate float, and will cause damage to the
vacuum motor. Damage due to foam is NOT
covered by warranty.
FIG. 11
FOR SAFETY: Do not operate machine without
bag and/or filter in place.
2. Close cover and fasten latches.
OPERATING SQUEEGEE KIT OPTION
3. Leave automatic float–off screen in place when
dry vacuuming. It can provide limited vacuum
motor protection for a faulty bag.
1. Lower squeegee to floor, lightly kick the pedal
forward to release from transport position
(Figure 13).
MACHINE OPERATION
FOR SAFETY: Do not operate machine unless
operator manual is read and understood.
Perform MACHINE SETUP instructions before operating
machine.
WARNING: Flammable materials or reactive
metals can cause an explosion or fire. Do not pick
up.
FIG. 13
2. Activate the ON/OFF switch.
OPERATING ACCESSORY TOOLS
1. Connect 3 m (10 ft) vacuum hose to machine
cover snout.
3. Begin operating by pushing and pulling machine in
either direction.
2. Select desired accessory tool and connect to
vacuum hose (Figure 12).
Typhoon 1610P/1612 (04–99)
Home
Find...
Go To..
9
OPERATION
4. During operation, the float shut-off screen will
automatically stop water intake when recovery
tank becomes full (See DRAINING RECOVERY
TANK).
ATTENTION: If foam develops in recovery tank
during wet vacuuming, use a quality defoamer
chemical to eliminate the foam. Foam buildup will
NOT activate float, and will cause damage to the
vacuum motor. Damage due to foam is NOT
covered by warranty.
5. To raise squeegee, step downward on pedal until
pedal engages in the transport position
(Figure 14).
FIG. 15
3. After draining recovery tank, open cover and
thoroughly rinse out tank with clean water.
4. Replace drain hose knob securely and return to
holder.
ATTENTION: Be certain drain hose knob is secure
to prevent suction loss.
ELEVATED DRAINING
NOTE: Machine must be equipped with pump–out
feature.
1. Disconnect vacuum hose from attachment tool or
from squeegee attachment.
FIG. 14
NOTE: Squeegee Kit can be used to pick up fine
particles (dust, sand, sawdust, etc.). Squeegee not
recommended for ordinary dry pick up.
2. Disconnect exhaust hose from rear of machine
and connect it to vacuum hose (Figure 16).
VACUUM MOTOR THERMAL PROTECTOR
Vacuum motor is thermally protected by a temperature
sensor device. It will trip if motor has an overload. If
motor should quit, wait 20 minutes for motor to cool
and remove obstruction before continuing.
DRAINING RECOVERY TANK
FIG. 16
3. Hang drain hose elbow over edge of drain sink
(Figure 17).
FLOOR DRAINING
1. Push machine to nearest floor drain, if not
available use a bucket to drain machine.
2. Remove drain hose from holder, twist off drain
hose knob and drain. Raise hose to stop flow of
water (Figure 15).
10
Home
Find...
Go To..
Typhoon 1610P/1612 (04–99)
OPERATION
ATTENTION: Always have float shut–off screen in
place before operating. During wet operation, the
shut–off float protects the vacuum motor from
water. During dry vacuuming, the float screen can
provide limited protection for a faulty filter bag.
7. Inspect vacuum hose regularly for holes, loose
cuff or clogged debris.
8. To maintain maximum performance, wash cloth
filter bag by hand with a mild detergent. Let bag
dry thoroughly before replacing.
9. Lubricate axle grease fittings with a water resistant
grease monthly.
FIG. 17
10. Lubricate front swivel casters with a silicone spray
monthly.
4. Pull up on drain lever and turn on switch
(Figure 18).
11. Check machine for loose nuts and bolts.
12. Every 250 hours of operation, check motor for
carbon brush wear, replace brushes if worn to
10 mm (0.38 in) or less.
STORING MACHINE
Before storing the machine perform the following
instructions:
1. Empty and rinse recovery tank and accessory
tools.
FIG. 18
2. Empty or replace vacuum bag.
5. Vacuum motor will pressurize tank and force
water up into drain sink.
3. Raise or remove squeegee assembly.
4. Store machine in a dry area in the upright position.
MAINTENANCE
ATTENTION: Do not store outdoors and avoid
getting wet. Do not allow machine to freeze.
To keep machine in good working condition, simply
follow machine’s daily, weekly and monthly
maintenance procedures.
ATTENTION: If storing machine in freezing
temperatures, be certain to drain machine of all
water. Damage due to freezing is not covered by
warranty.
WARNING: Hazardous Voltage. Shock or
electrocution can result. Unplug machine before
servicing.
1. Drain and rinse recovery tank after wet
vacuuming.
2. Remove and clean float shut–off screen from
recovery tank.
3. Clean squeegee blades with a cloth. Replace
blades when they become worn.
4. Check bag for fullness, empty bag at 3/4 full.
5. Wipe machine housing with a nonabrasive,
nonsolvent cleaner.
6. Check cords and cord grips for damage. If worn or
damaged, replace immediately. Coil cord neatly.
Typhoon 1610P/1612 (04–99)
Home
Find...
Go To..
11
OPERATION
TROUBLE SHOOTING
PROBLEM
CAUSE
SOLUTION
Machine does not run.
ON/OFF switch is OFF.
Vacuum not plugged into wall outlet.
Faulty ON/OFF switch.
Faulty wiring.
Faulty power cord.
Building circuit breaker tripped.
Turn switch to ON.
Plug power cord to wall outlet.
Replace switch.
Contact Service Center.
Contact Service Center.
Reset circuit breaker and change to a
different power circuit.
Find air obstruction. Let motor cool for 20
minutes.
Contact Service Center.
Clear hose.
Replace hose.
Remove hose from elbow and remove
clogged material.
Tighten drain knob.
Latch both sides of lid securely.
Inspect all gaskets, and replace if
necessary.
Empty tank or bag.
Close drain valve.
Connect elbow to plug securely.
Wipe off squeegee blades.
Replace squeegee blades.
Tighten thumbscrews.
Push vacuum hose onto squeegee mount
securely.
Vacuum motor over heated.
Machine has little or no
suction.
ti
Faulty vacuum motor.
Hose is clogged.
Holes in hose.
Intake elbow in lid is clogged.
Drain hose knob is loose or open.
Lid is not securely latched.
Worn gasket which is leaking air.
Machine with Pump–Out
f t
feature:
Squeegee
q
g has poor pick
up.
12
Recovery tank or bag is full.
Drain valve is open.
Drain hose elbow is loose or off plug.
Debris is wedged under squeegee blade.
Squeegee blades are worn.
Squeegee blade is loose.
Vacuum hose connection on squeegee
mount is loose.
Home
Find...
Go To..
Typhoon 1610P/1612 (04–99)
WIRING DIAGRAM
120V
VACUUM
MOTOR
MASTER
SWITCH
BLK
BLK
WHT
GRN
GRN
GRN
WHT
BLK
WHT
GRN
POWER CORD
220V
VACUUM
MOTOR
MASTER
SWITCH
BRN
BLU
BLU
GRN
GRN
BRN
BLU
GRN
BRN
GRN
POWER CORD
Typhoon 1610P/1612 (04–99)
Home
Find...
Go To..
13
PARTS LIST
TANK GROUP
8
7
9
20
21
14
10
6
19
11
22
5
15
17
16
13
4
23
24
25
27
28
29
12
18
2
31
20
26
3
49
1
30
44
43
45
46
47
36
42
41
32
39
40
33
38
37
34
48
35
14
Home
Find...
Go To..
Typhoon 1610P/1612
(04–99)
PARTS LIST
TANK GROUP
REF
PART #
DESCRIPTION
QTY.
REF
PART #
DESCRIPTION
QTY.
1
140028
WASHER, FLAT
4
28
140011
WASHER, FLAT
4
2
140017
WASHER, LOCK
4
29
140802
SCREW, 8–32X5/8
4
3
140231
SCREW, 3/8–16X1 1/2
4
30
608616
TANK, GREEN (16 GAL. MODEL)
1
4
608618
HANDLE, GREEN
1
608615
TANK, GREEN (16 GAL. MODEL W/PUMP-
1
5
140825
SCREW, #6X1/2
2
6
230696.BK
HANGER, DRAIN HOSE
1
7
19417
SWITCH
1
8
608613
COVER, GREEN
1
9
130201
ASM., CORD 16/3X28” (120V)
1
10
140195
SCREW, 1/4–20X1/2
4
11
140000
WASHER, FLAT
4
12
230318
HINGE, COVER (16 GAL. MODEL)
1
13
140195
SCREW, 1/4–20X1/2
4
14
100097
15
140824
16
578244000
17
140197
GASKET, COVER (16 GAL. MODEL)
2
WASHER, LOCK
2
2
18
130110
BUSHING, STRAIN RELIEF
1
19
230497
BRACKET, AIR DEFLECTOR
1
20
140932
LATCH, RUBBER & KEEPER
LATCH, CHROME (PUMP–OUT MODEL)
2
230512
KEEPER (PUMP–OUT MODEL)
2
21
140023
WASHER, LOCK
4
22
140801
SCREW, 8–32X3/8
4
23
140824
SCREW, 1/4–20X5/8 (16 GAL. MODEL)
2
24
578244000
WASHER, LOCK (16 GAL. MODEL)
2
25
140003
WASHER, FENDER (16 GAL. MODEL)
2
26
230482.BK
BRACKET, SUPPORT (16 GAL. MODEL)
1
27
28990
NUT, LOCK
4
Typhoon 1610P/1612
Find...
BAG, PAPER
1
900105
BAG, CLOTH (16 GAL. MODEL)
1
33
103065
CASTER, SWIVEL
1
34
140015
WASHER, LOCK
4
35
140226
SCREW, 5/16–18X5/8
4
36
130250
CORD, 16/3X50’
1
37
140307
CLAMP
1
130041
WIRE TIE
1
701058
ASM., DRAIN HOSE
1
40
160457
HOSE, DRAIN
1
41
140921
SLEEVE
1
42
140072
CLAMP
2
∇43
701061
ASM., PLUG
1
44
230831
KNOB
1
45
230882
STRAP
1
46
140056
WASHER, FENDER
1
47
140955
PLUG
1
48
160481
HOSE, VACUUM
1
49
130267
CORD, HANDLE 16/3X30”
1
∇ ASSEMBLY
INCLUDED IN ASSEMBLY
DECAL LIST
REF
PART #
DESCRIPTION
N/S
602596
DECAL, WARNING
1
N/S
120657
DECAL, PUMP–OUT INST.
1
N/S
608186
DECAL, “NOBLES”
1
N/S
608492
DECAL, “TYPHOON 1610P”
2
N/S
608493
DECAL, “TYPHOON 1612”
2
(04–99)
Home
900102
32
38
2
140953
31
∇39
1
SCREW, 1/4–20X5/8
SCREW, 10–24X3/8
OUT)
Go To..
QTY.
15
PARTS LIST
BASE GROUP
37
35
38
34
28
31
32
27
33
30
39
29
25
26
24
23
20
40
22
15
14
18
21
17
16
19
3
13
12
4
11
5
10
2
9
41
8
42
43
44
7
6
1
36
16
Home
Find...
Go To..
Typhoon 1610P/1612
(04–99)
PARTS LIST
BASE GROUP
REF
PART #
DESCRIPTION
1
140195
SCREW, 1/4–20X1/2
2
2
140003
WASHER, FENDER
2
3
103060
WHEEL (16 GAL. MODEL)
2
4
140045
WASHER, FLAT
2
5
230317
AXLE (16 GAL. MODEL)
1
6
140553
QTY.
SCREW, 1/4–20X1/2
140016
WASHER, LOCK
4
8
230746
BRACKET, AXLE
2
140201
SCREW, 3/8–16X3/4
140017
WASHER, LOCK
2
11
140028
WASHER, FLAT
2
13
230486.BK
PLATE, COVER (16 GAL. MODEL)
1
230331.BK
PLATE, COVER (16 GAL. W/PUMPOUT)
1
140900
SCREW, 10–24X3/4
140519
NUT, KEP
3
15
100095
GASKET, VAC MOTOR
1
140504
NUT, CONDUIT
140000
WASHER, FLAT
5–6
18
140195
SCREW, 1/4–20X1/2
5–6
140340
2
130417
MOTOR, VACUUM 120V (TYPHOON
1
1
17
19
–BRUSH, CARBON (2/PK)
1
14
16
DESCRIPTION
190155
2
10
12
PART #
27
SCREW, #10X5/8
4
QTY.
1612)
4
7
9
REF
600272
–BRUSH, CARBON (2/PK)
2
130415
MOTOR, VACUUM 120V (TYPHOON 1610P)
1
190161
–BRUSH, CARBON (2/PK)
2
130403
MOTOR, VACUUM 230V (TYPHOON 1610P)
1
190158
–BRUSH, CARBON (2/PK)
2
28
100038
GASKET, MOTOR
1
29
140003
WASHER, FENDER
4
30
578244000
WASHER, LOCK
4
31
140199
SCREW, 1/4–20X4 1/2 (TYPHOON 1612)
4
32
140308
CLAMP
2
33
180613
FLOAT, SCREEN SHUT–OFF
1
34
100381
ELBOW, VACUUM TUBE
1
35
100096
GASKET, VACUUM TUBE
1
37
700435
ELBOW
1
38
160482
HOSE, VACUUM
1
39
100380
MOUNT, VACUUM MOTOR
1
100302
MOUNT, VAC. MOTOR (PUMP–OUT
1
MODEL)
20
230496.BK
SUPPORT, DRAIN HOSE
1
40
140501
NUT, LOCK
4
21
578244000
WASHER, LOCK
2
41
12481
NUT
4
22
140824
SCREW. 1/4–20X5/8
2
42
130164
PLUG, DOME (220V)
1
23
230522
BRACKET, MOTOR MOUNT
1
43
140022
WASHER, LOCK (120V)
1
24
140900
SCREW, 10–24X3/4
1
44
611110000
BREAKER, CIRCUIT 10A
25
100143
GASKET, MOTOR
1
130670
BREAKER, CIRCUIT 12A
26
140519
NUT, KEP
3
Typhoon 1610P/1612
(04–99)
Home
Find...
Go To..
1
(PUMP–OUT
1
MODEL)
17
PARTS LIST
PUMP–OUT GROUP
33
3
4
34
5
32
35
36
37
2
42
44
41
1
8
38
39
45
40
31
6
7
30
9
43
10
48
13
11
47
19
12
28
29
27
24
25
15
46
26
16
14
21
17
22
18
23
18
20
Home
Find...
Go To..
Typhoon 1610P/1612
(04–99)
PARTS LIST
PUMP–OUT GROUP
REF
PART #
DESCRIPTION
QTY.
REF
PART #
DESCRIPTION
1
160482
HOSE, VACUUM
1
∇30
701059
ASM., DRAIN HOSE PUMPOUT
1
2
140308
CLAMP
2
31
160458
HOSE, DRAIN
1
3
700461
VALVE, GATE
1
32
140307
CLAMP
1
4
100096
GASKET,VAC TUBE
1
33
230357
DOWNSPOUT, PVC 1 1/2”
1
5
100381
ELBOW,VAC TUBE
1
34
140899
SCREW, 10–24X1 1/4
1
6
140837
SCREW, 10–24X3/8
4
35
140011
WASHER, FLAT
1
7
140018
WASHER, LOCK
4
36
140950
PLUG, DRAIN HOSE
1
8
230334
HANDLE, AIR VALVE
1
37
230394.BK
BRACKET, DRAIN HOSE
1
9
230493
SPACER
1
38
140825
SCREW, #6X1/2
3
10
230338
BRACKET, AIR VALVE
2
39
140522
NUT, LOCK 3/8–16
1
11
210231
VALVE, DRAIN
1
40
607498
TAPE, BUMPER 1/16X1 (3.2 FT)
1
12
100302
HOUSING, VACUUM MOUNT
1
41
102531
FILTER, FOAM
1
13
140501
NUT, LOCK
3
42
608620
HOUSING, FILTER, GREEN
1
14
140000
WASHER, FLAT
3
43
160459
HOSE, VAC W/CUFF
1
15
100038
GASKET, VACUUM MOTOR
1
230905
TUBE, INLET
1
16
130415
MOTOR, VACUUM 120V
1
44
140012
WASHER, FLAT
4
1
45
140341
SCREW, #10X1
4
190161
BRUSH, CARBON (2/PK)
QTY.
17
2998.28
SCREW, 1/4–20X3 1/2
3
46
140504
NUT, COUDUIT
1
18
100095
GASKET, VACUUM MOTOR
1
47
140000
WASHER, FENDER
3
19
230331.BK
PLATE, COVER (16 GAL. MODEL)
1
48
602744
SCREEN, GATEVALVE
1
20
140900
SCREW, 10–24X3/4
1
21
230746
BRACKET, AXLE
2
22
140195
SCREW, 1/4–20X1/2
2
23
140003
WASHER, FENDER
2
24
103060
WHEEL
2
25
140063
WASHER, FLAT
2
26
230317
AXLE (16 GAL. MODEL)
1
27
140519
NUT,, KEP
3
28
140195
SCREW, 1/4–20X1/2
6
29
140000
WASHER, FLAT
6
Typhoon 1610P/1612
∇ ASSEMBLY
INCLUDED IN ASSEMBLY
(04–99)
Home
Find...
Go To..
19
OPTIONAL ACCESSORIES
SQUEEGEE KIT BREAKDOWN
10
9
2
7
3
8
6
5
4
11
9
8
1
Factory Installed
on Machine.
25
26
24
15
13
20
21
14
23
22
17
17
16
18
20
Home
12
19
Find...
Go To..
Typhoon 1610P/1612
(04–99)
OPTIONAL ACCESSORIES
SQUEEGEE KIT BREAKDOWN
REF
PART #
DESCRIPTION
QTY.
REF
∇
190108
190972
PART #
DESCRIPTION
SQUEEGEE KIT 67CM (26 IN)
1
SQUEEGEE KIT 84CM (33 IN)
1
190958
SQUEEGEE KIT 99CM (39 IN)
1
1
230453.BK
WELDMENT, SQUEEGEE LIFT
1
2
230456
PEDAL, LIFT
1
14
100150
GASKET
1
15
230725.BK
PLATE, REAR 67CM (26 IN)
1
230669.BK
PLATE, REAR 84CM (33 IN)
1
230685.BK
PLATE, REAR 99CM (39 IN)
1
230723.BK
PLATE, FRONT 67CM (26 IN)
3
230454
BRACKET, SQUEEGEE MOUNT
1
1
230670.BK
PLATE, FRONT 84CM (33 IN)
1
4
140232
SCREW, 3/8–16X1-1/4
1
5
140925
SPACER, 3/16
1
230686.BK
6
140028
WASHER, FLAT 3/8
1
7
140515
NUT, LOCK NYLON 3/8-16
1
8
630258
PIN, CLEVIS
3
18
9
612254000
16
17
QTY.
PLATE, FRONT 99CM (39 IN)
1
603659
BLADE, SQUEEGEE 67CM (26 IN)
2
603661
BLADE, SQUEEGEE 84CM (33 IN)
2
603662
BLADE, SQUEEGEE 99CM (39 IN)
140890
SCREW, 10-24X1/2
18-28
18-28
2
PIN, HAIR
3
19
140018
WASHER, #10 INT LOCK
10
102560
PAD, NONSTICK
1
20
27257
KNOB, SQUEEGEE
2
11
160462
HOSE, VACUUM 1.5 X 84CM (33 IN)
1
21
140221
SCREW, 5/16-18X1-1/4
2
12
602831
ASM., SQUEEGEE 67CM (26 IN)
1
22
630450
WHEEL
2
603494
ASM., SQUEEGEE 84CM (33 IN)
1
23
140799
SCREW, 5/16-18X1-1/2
2
603496
ASM., SQUEEGEE 99CM (39 IN)
1
24
700844
ASM., SQUEEGEE ROLLER
2
230727.BK
WELDMENT, SQUEEGEE 67CM
(26 IN)
1
25
140226
SCREW, 5/16-18X5/8
2
26
140015
WASHER, LOCK
2
230682.BK
WELDMENT, SQUEEGEE 84CM
(33 IN)
1
230692.BK
WELDMENT, SQUEEGEE 99CM
(39 IN)
1
13
Typhoon 1610P/1612 (04–99)
Home
Find...
∇ ASSEMBLY
INCLUDED IN ASSEMBLY
Go To..
21
OPTIONAL ACCESSORIES
1
2
3
2
REF
PART #
DESCRIPTION
1
190108
KIT, 66CM (26 IN) SQUEEGEE
1
190972
KIT, 84CM (33 IN) SQUEEGEE
1
190958
KIT, 99CM (39 IN) SQUEEGEE
1
16593
∇KIT, ACCESSORY TOOL
1
6108.1
TWO
1
2
22
QTY.
PIECE WAND
6117
DUSTING
6057
10CM
6170
CREVICE
BRUSH
1
(4 IN) UPHOLSTERY TOOL
TOOL
14043
41CM
13840
SQUEEGEE
(16 IN) FLOOR TOOL
TOOL
Home
1
REF
PART #
DESCRIPTION
3
190142
∇KIT, ACCESSORY TOOL
1
190722
TWO
1
603840
36CM
(14 IN) CARPET TOOL
SCALLOPED FACE
1
13840
36CM
1
PIECE WAND
(14 IN) SQUEEGEE TOOL
QTY.
∇ ASSEMBLY
INCLUDED IN ASSEMBLY
1
1
1
Find...
Go To..
Typhoon 1610P/1612
(04–99)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising