automatic sliding door operator drawings 2015

automatic sliding door operator drawings 2015
AUTOMATIC
SLIDING DOOR
OPERATOR
DRAWINGS
2015
—
CONTENTS PAGE
—
Product
Drawing number
EL 301
Aluminium frame shopfront
Aluminium door SA1
Aluminium door SA2
Frameless glass door 12mm
Frameless glass door 15mm
Frameless glass door 19mm
Frameless with top & bottom rail
Telescopic aluminium frame door (TS 301)
Telescopic frameless with top and bottom rail
Telescopic frameless with top rail K-TYPE (TS 301)
Compact profile aluminium door SA1
Compact profile aluminium door SA2
Compact profile frameless glass door 12mm
Compact profile frameless glass door 15mm
Slimline frame system SA1
Slimline frame system SA2
Slimline frame system plan view
Timber door SA1
1A201107
10201070
1A201084
1A201086
1B201087
92031210
10201201
10701030
10701031
10701032
10501032
10501037
10501031
10501034
10201100
10201096
10201102
92031517
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
HD 200
Aluminium door SA1
Aluminium door SA2
Frameless glass door 12mm
Telescopic aluminium frame door (TS 200)
Telescopic frameless with top and bottom rail
Telescopic frameless with top rail K-TYPE
Slimline frame system SA1
Slimline frame system SA2
10601000
10601001
10601002
20801000
20801003
20801009
10601005
10601006
22
23
24
25
26
27
28
29
AL 401
Aluminium door SA1
Frameless glass door 12mm
Frameless glass door 15mm
Frameless glass door 19mm
10101075
1A101076
1B101078
1B101077
30
31
32
33
AL 501
Aluminium door SA2
Frameless glass door 19mm
Frameless glass door 25mm
50301002
50301000
50301001
34
35
36
B08013001
B08013015
A08013012
B08003023
37
38
39
40
FLOOR GUIDES
Type A: Standard to suit aluminium door frame
Type C: Telescopic to suit aluminium door frame
Type F: Nylon 12mm for frameless glass door
Type H: Frameless glass door with bottom rail
Installation details
Door Height Calculations
Aluminium frame door fittings and adjustments
Frameless glass fittings and adjustments
Frameless glass hole detail (TIB 40)
DORMA CDS 43S top rail glass preparation
Standard floor guide fittings and adjustments
Access requirements for above ceiling mounting
Page
41
42
43
44
45
46
47
48
EL 301
—
Aluminium frame shopfront (1A201107)
DOOR HEIGHT = FFL TO
UNDERSIDE OF TRANSOM
(10MM CLEARANCE =
10MM DOOR COVER)
EL 301
—
Aluminium door SA1 (10201070)
Operator drawings
EL 301
—
Aluminium door SA2 (1A201084)
EL 301
—
Frameless glass door 12mm (1A201086)
Operator drawings
EL 301
—
Frameless glass door 15mm (1B201087)
EL 301
—
Frameless glass door 19mm (92031210)
ALLOW APPROX.
15mm CLEARANCE
BETWEEN TOP OF OPERATOR
AND FINISHED CEILING LINE
TO ALLOW FOR REMOVAL OF
FASCIA.
HINGED FASCIA IMPORTANT:
THIS AREA OF OPERATOR
MUST REMAIN ACCESSIBLE.
NO RIGID FIXINGS TO THIS
AREA.
M8x1.25 PITCH GRADE 8.8
FIXING @ 300mm CTRS.
MINIMUM OR AS PER
YOUR DESIGN ENGINEERS SPEC.
M6x1.00 PITCH GRADE 8.8
FIXINGS @ 300mm CTRS.
MINIMUM OR AS PER
YOUR DESIGN ENGINEERS SPEC.
40
40
9
Operator drawings
EL 301
—
Frameless with top & bottom rail (10201201)
153.40
15.00
FINISHED CEILING LEVEL
ALLOW APPROX.
15mm CLEARANCE
BETWEEN TOP OF OPERATOR
AND FINISHED CEILING LINE
TO ALLOW FOR REMOVAL OF FACIA
240.00
FIXINGS REQUIRED TO THIS
FACE OF OPERATOR
@ APPROX. 600mm c/c AS PER
YOUR ENGINEERS DETAILS
217.50
266.00
60.00
HINGED FASCIA
IMPORTANT: THIS AREA OF
OPERATOR MUST REMAIN
ACCESSIBLE. NO RIGID FIXINGS
TO THIS AREA.
7.70
44.50
UNDERSIDE OF
OPERATOR
20.90
30.00
4.60
REINFORCEMENT TO WEB
30.00
12.50
85.00
96.00
CDS43S
TOP RAIL
11.40
34.00
CLEAR OPENING HEIGHT
27.00
12mm THICH TOUGHENED
GLASS DOORS
R3.00
R.300
10.00
UNIT MOUNTING HEIGHT
70.00
53.00
28.40
25.30
15.00
Ø19.00
Ø19.00
3.00
34.00
80.00
26.00
GRAPHITE IMPREGNATED
NYLATRON ROLLERS
85.00
26.00
CDS41S - BOTTOM SLIDING DOOR RAIL
58.00
10.00
6.50
6.50
26.00
FLOOR GUIDE DETAIL
FLOOR GUIDE WITH
GRAPHITE IMPREGNATED
NYLATRON ROLLERS
PART No. B08013018
EL 301
—
Telescopic aluminium frame door (10701030)
UNDERSIDE OF
OPERATOR
Operator drawings 1
EL 301
—
Telescopic frameless with top and bottom rail (10701031)
UNDERSIDE OF
OPERATOR
EL 301
—
Telescopic frameless with top rails (10701032)
Operator drawings
EL 301
—
#OMPACTPROlLEALUMINIUMDOOR3!
UNDERSIDE OF
OPERATOR
EL 301
—
#OMPACTPROlLEALUMINIUMDOOR3!
Operator drawings
EL 301
—
#OMPACTPROlLEFRAMELESSGLASSDOORMM
EL 301
—
#OMPACTPROlLEFRAMELESSGLASSDOORMM
Operator drawings
EL 301
—
Slimline frame system SA1 (10201100)
EL 301
—
Slimline frame system SA2 (10201096)
Operator drawings
EL 301
—
Slimline frame system plan view (10201102)
EL 301
—
Timber door SA1 (92031517)
153.40
15.00
ALLOW APPROX. 15mm
CLEARANCE BETWEEN TOP OF
OPERATOR AND FINISHED CEILING
LINE TO ALLOW FOR REMOVAL OF
FASCIA
85.00
217.50
266.00
240.00
FIXINGS REQUIRED TO THIS
FACE OF OPERATOR @
APPROX. 600mm c/c AS PER
YOUR ENGINEERS DETAILS.
60.00
7.70
44.50
HINGED FASCIA
IMPORTANT: THIS AREA
OF OPERATOR MUST BE
ACCESSIBLE. NO RIGID
FIXINGS TO THIS AREA.
20.90
UNDERSIDE OF
OPERATOR
FULL LENGTH MILD STEEL FLAT
REINFORCING FIXED TO TOP OF
TIMBER DOOR FOR MOUNTING
DOOR HANGER BRACKETS
6.00
90.00
6.00
28.40
7mm I.D x 1.6mm THICK
GAL. MILD STEEL WASHERS
25.00
50.00
50.00
6.00
85.00
Ø22.00 DELRON CORED
RUBBER ROLLER
37.50
REINFORING METAL CHANNEL
FITTED TO BOTTOM OF TIMBER
DOOR AND NOT PROTRUDING
BELOW BOTTOM OF DOOR LEAF
FULL LENGTH OF DOOR TRAVEL
MILD STEEL BRACKET
31.00
5.00
23.00
57.00
1/4 INCH B.S.W LOXIN FIXINGS
45.00
10.00
32.00
Operator drawings
HD 200
—
Aluminium door SA1 (10601000)
HD 200
—
Aluminium door SA2 (10601001)
Operator drawings
HD 200
—
Frameless glass door 12mm (10601002)
HD 200
—
TS 200 Telescopic aluminium frame door
(20801000)
Operator drawings
HD 200
—
TS 200 Telescopic frameless with top and bottom rail
(20801003)
HD 200
—
TS 200 Telescopic frameless with top rail K-TYPE (20801009)
Operator drawings
HD 200
—
Slimline frame system SA1 (10601005)
HD 200
—
Slimline frame system SA2 (10601006)
Operator drawings
AL 401
—
Aluminium door SA1 (10101075)
AL 401
—
Frameless glass door 12mm (1A101076)
Operator drawings
AL 401
—
Frameless glass door 15mm (1B101078)
AL 401
—
Frameless glass door 19mm (1B101077)
Operator drawings
AL 501
—
Aluminium door SA2 (50301002)
AL 501
—
Frameless glass door 19mm (50301000)
Operator drawings
AL 501
—
Frameless glass door 25mm (50301001)
FLOOR GUIDE
—
Type A: Standard to suit aluminium door frame (B08013001)
Operator drawings
FLOOR GUIDE
—
Type C: Telescopic to suit aluminium door frame (B08013015)
FLOOR GUIDE
—
Type F: Nylon 12mm for frameless glass door (A08013012)
Operator drawings
FLOOR GUIDE
—
Type H: Frameless glass door with bottom rail (B08003023)
41.00
6.00
82.00
35.00
6.00
35.00
140.00
7.00
70.00
26.00
40.00
30.00
40.00
30.00
SELF TAPPING SCREWS
No. 10x12mm TYPE C.(2)
35.00
35.00
35.00
6.00
25.30
6.00
82.00
BOTTOM SLIDING DOOR RAIL
D42LS/950mm
15.00
30.00
33.00
24.50
33.00
24.00 MIN
17.50
35.00
33.00
41.00
8.00
41.00
INSTALLATION & COMMISSIONING GUIDE
—
Operator installation
Factors for Installation Mounting Height of Operator
STANDARD MOUNTING HEIGHT
POWERLEAD - LOOKING AT UNIT
EL 301
MODELL
+25mm Min
EL 301=LHS
TELESCOPIC (TS 301)
+44mm Min
TS 301=LHS
COMPACT PROFILE (CP 301)
+20mm Min
TS 301=LHS
HD 200
+30mm Min
HD 200=RHS
TS 200
+54mm Min
TS 200=RHS
AL 401
+25mm Min
AL 401=LHS
Note: Standard mounting height is generally taken as the operator cowl mounting height above underside of transom.
1. Unpack and inspect the automatic door operator. It should be free of any visual defects, dents or
scratches.
2. Remove the fascia and check that all the accessories for the commissioning are inside. This will include
the endplates, floor guides, sensors, operator manual and PE cells.
3. Measure the operator length checking that it is the correct size for the application, taking into the
consideration the endplate thickness.
4. Remove the door brackets so they can be attached to the top of the door later. Remove the hanger bars to
allow for the drilling of fixing holes through the cowl. This is done by unscrewing.
5. Mark the centre of the operator, this will allow you to align it with the centre mark on the wall. If possible
pre-drill fixing holes through the cowl prior to installation.
6. De-burr all fixing holes drilled.
7. Using suitable clamps position the blocks of timber at the operator height.
8. Fit the endplates to the operator before installation, as this may be difficult afterwards.
9. Raise the operator into position and check for level. Fix the operator using the appropriate fixings.
10. Ensure all fixings are secure and the operator is well fastened prior to removing the clamps.
11. The operator is now installed and ready for commissioning.
Operator drawings
DOOR HEIGHT CALCULATIONS
—
OPERATOR
BRACKETS
DRAWING
UNIT HEIGHT DOOR HEIGHT CALCULATION
EL301
SA-1 Framed
10201070
266mm
FFL to top of operator minus 266mm
EL301
SA-2 Framed
1A201084
266mm
FFL to top of operator minus 266mm
EL301
12mm Glass
1A201086
266mm
FFL to top of operator minus 173mm
EL301
15mm Glass
1B201087
266mm
FFL to top of operator minus 175mm
EL301
19mm Glass
92031210
266mm
FFL to top of operator minus 175mm
TS301
Framed
1A701030
266mm
FFL to top of operator minus 260mm
TS301
Glass Rails
1A701031
266mm
FFL to top of operator minus 260mm
CP 301
SA-1 Framed
10501032
165mm
FFL to top of operator minus 170mm
CP301
SA-2 Framed
10501037
165mm
FFL to top of operator minus 170mm
CP301
12mm Glass
10501031
165mm
FFL to top of operator minus 79mm
CP301
15mm Glass
10501034
165mm
FFL to top of operator minus 81mm
HD200
SA-1 Framed
10601000
155mm
FFL to top of operator minus 155mm
HD200
SA-2 Framed
10601001
155mm
FFL to top of operator minus 155mm
HD200
12mm Glass
10601002
155mm
FFL to top of operator minus 59mm
TS200
Framed
20801000
266mm
FFL to top of operator minus 259mm
TS200
Glass Rails
20801003
266mm
FFL to top of operator minus 261mm
AL401
SA-1 Framed
10101075
266mm
FFL to top of operator minus 266mm
AL401
12mm Glass
1A101076
266mm
FFL to top of operator minus 173mm
AL401
15mm Glass
1B101078
266mm
FFL to top of operator minus 175mm
AL401
19mm Glass
1B101077
266mm
FFL to top of operator minus 175mm
AL501
SA-2 Framed
50301002
266mm
FFL to top of operator minus 266mm
AL501
19mm Glass
50301000
266mm
FFL to top of operator minus 175mm
AL501
25mm Glass
50301001
266mm
FFL to top of operator minus 175mm
FITTING OF ALUMINIUM FRAMED DOOR
—
1. Ensure the Automatic Sliding Door Operator is at the correct height.
2. Remove Door Brackets from Hanger Bar and attach using suitable fixings to top of metal frame door.
Note: Always fix Door Brackets so they are as close as possible to the Track Wheels to give maximum stability
during operation.
Hanger Bar
Door Bracket
Detail on construction
& installation of metal
framed doors
Stile
Bottom Rail
Note: Door frame webbing to be removed to ensure unimpeded door travel.
Operator drawings
FRAMELESS GLASS DOOR
—
Fitting Adjustment
1. Ensure the Automatic Sliding Door Operator is at the correct height.
2. Pull Frameless Hanger Bar Assemblies to the half open position.
3. Disconnect Chain Bracket and remove continuous Hanger Bar, leaving Frameless Bogies on the track.
4. Rotate cam into position to allow fitting of glass.
5. Place Door Leaf on packer at floor level and fit top to Frameless Bogies.
Note: Nominal 10mm clearance from F.F.L
6. Refit continuous Hanger Bar to complete Frameless Hanger Bar Assembly.
DO NOT FULLY TIGHTEN NUTS
7. To align Door Leaf, rotate Glass Spacer Cam via both 12mm bolts. (Note: Do not raise/lower door weight via
nylon cams - door weight to be chocked/supported)
8. When correct height achieved, tighten 12mm nuts.
9. Check Door Leaf travels freely along track and then re-connect Chain Bracket to the Frameless Hanger Bar
Assembly.
10. BEFORE TURNING THE OPERATOR ON, MANUALLY CHECK THAT THE CONTACT AT THE MEETING OF
THE DOORS IS NOT GLASS TO GLASS.
Frameless Glass Door, Frameless Bogies and Continuous Hanger Bar (Glass hole detail for 10/12mm and
15/19mm thick glass panels, shown up to <1300mm W)
37mm for 10/12mm
54mm for 15/19mm
FRAMELESS GLASS DOOR
—
Glass Hole Details for 10/12mm & 15/19mm thick panel width <1300mm to <1800mm (TIB40)
37mm for 10/12mm
54mm for 15/19mm
Glass hole detail for panel width >1800mm
37mm for 10/12mm
54mm for 15/19mm
Operator drawings
DOOR RAILS
—
CDS 43S DORMA top rail preparation
(10 & 12mm shown)
CDS 43S SPECIFICATION: On-Eazi 85mm High Bolt through Top Door
Rail to suit most automatic or manual Sliding Door Systems.
Specify Glass Thickness 10, 12, 15 or 19mm. Alternative rail cover heights
on application. ILLUSTRATED
FINISHES
ALUMINIUM:
MILL, SAA
STAINLESS: SSS, PSS
Special finishes available
on request.
STANDARD FLOOR GUIDE INSTALLATION
—
PLACED S UCH THAT DOOR
CAN FULLY CLOSE
VIEW FROM INSIDE
OUTSIDE
SIDELIGHT
.
SIDELIGHT
SIDELIGHT
½ DOOR
THICKNESS +
10mm
1
CLOSE DOORS FULLY. SQUARE AND
ALIGN DOORS. CHECK DOORS
PARALLEL TO JAMBS. MARK POSITIONS.
2
PLACE FLOORGUIDE SO DOORS ARE
PLUMB.
OUTSIDE
SIDELIGHT
3
DRILL 2 × Ø13mm HOLES AND FIX WITH
SUPPLIED LOXIN AND WASHERS.
12
(if necessary)
5
4
ENSURE DOORS CAN CLOSE FULLY.
(MILLING INTERNAL WEB OF DOOR MAY
BE NECESSARY)
TURN FLOORGUIDE UNTIL APPROX. 1mm
CLEARANCE BETWEEN ROLLER AND RAIL.
SIDELIGHT
CHECK CLEARANCE BY MOVING DOOR LEAF
BACK AND FORTH.
VIEW FROM INSIDE
SIDELIGHT
SIDELIGHT
NOTE : Instructions shown are for
STANDARD aluminium doors and
STANDARD Floor guides.
6
HANG, SQUARE AND ALIGN DOORS.
CHECK DOORS PARALLEL TO JAMBS (10mm
CLEARANCE). CHECK DOORS CLOSE FULLY.
8
Operator drawings
EL 301
—
Access requirement for above ceiling mounting
ACCESS TO OPERATOR REQUIRED.
400MM WIDE X LENGTH OF OPERATOR.
(IF PANELS HINGED, SWING AWAY FROM OPERATOR
CEILING SUPPORT TO BE
CLEAR OF OPERATOR
FINISHED POINT OF CEILING
DEPENDENT ON THICKNESS OF DOOR
FIXINGS REQUIRED TO THIS
FACE OF OPERATOR @ APPROX.
60mm c/c AS PER YOUR
ENGINEERS DETAILS
UNDERSIDE OF
OPERATOR
NOTES
—
NOTES
—
NOTES
—
AMA03005, 06/15, OPERATOR DRAWINGS
*Subject to change without notice
DORMA Australia
(EAD/FlCE
46-52 Abbott Road
HALLAM
6ICTORIA
0HONE
INFOAU DORMACOM
WWWDORMACOMAU
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising