Simon XTi Quick Operation Guide
Simon® XTi Quick Operation Guide
®
This is the Quick Operation Guide for the Simon XTi system
(models 600-1054-95R-16 & 600-1054-95R-16-CN). The
®
Simon XTi provides a graphical user interface for
programming and system operation. A piezo siren is provided
for alarm and status annunciation. A speaker and microphone
is provided for 2-way voice communication with the central
station.
Note: Upon initial installation, the battery may not be fully
charged for as long as 36 hours. A low battery icon will be
present and trouble beeps will sound until the battery is
sufficiently charged. After the initial charge, should the
panel lose AC Power and experience a low battery
condition, the icon will appear and trouble beeps will
sound unless silenced. You can silence trouble beeps by:
•
Safety Information
Arming or disarming the system.
or
IMPORTANT SAFETY INFORMATION. READ ENCLOSED
WARNINGS AND SAFETY INFORMATION.
•
This will disable the sounder for 4 hours but the trouble
indication will remain until the battery is recharged.
WARNING: CHOKING HAZARD. The product accessory
bag contains items that could be choking hazards. Please keep
away from small children.
ATTENTION: Le sachet d'accessoires produit contient des
éléments qui pourraient être les dangers d'étouffement.
Veuillez garder hors de la portée des jeunes enfants.
Pressing the STATUS & SETTINGS icon and
pressing LISTEN next to Panel Status.
Contact your installer to replace your backup battery.
This system is intended to be checked by a qualified technician
at least once every 3 years.
Home Screen
Operation
®
Use this document to quickly begin operating your Simon XTi
®
security system. Refer to the Simon XTi User Manual for full
operating details and programming options. To download the
®
Simon XTi User Manual see “Contact information” on page 9.
Note: The default master code is 1-2-3-4 when the security
system is shipped from the factory. You should change your
code after your system is installed (see “Programming” on
page 5).
There are multiple ways to reach the Home screen (Table 1
below describes its features):
•
•
•
To operate the security system:
•
Use the home screen icons to arm/disarm the system
when you enter or exit your home and to determine which
sensors are active and the system status.
•
Use the emergency screen to communicate with the
central monitoring station to report police, fire, or
emergency alarms.
•
By pressing the close icon. Depending on the screen you
are currently on, you may need to press the close icon
multiple times.
After a period of inactivity, the Home screen will return
(unless you set a blank screen as your default screen
saver).
If an alarm occurs, the screen will automatically return to
the Home screen.
Note: The touch screen will automatically blank at 2:00 am
daily for 60 minutes. Touch the screen to reactivate.
Table 1: Home Screen
From the home screen, press the Status & Settings
®
icon to program certain user features. Refer to the Simon
XTi User Manual for more information.
Icon
Description
Access the emergency screen to select the
appropriate emergency icon (Panic, Police, or
Fire).
Time
The current system time.
P/N 466-5235 • REV A • 06APR16
Icon
Description
Depicts the status of the AC power and battery.
Note: These icons only appear in red on the
main screen if the backup battery is not fully
charged or AC power is not working correctly.
This yellow triangle indicates faults within the
system.
This will appear on the home screen in the event
of an alarm. Messages will also display on this
icon describing what caused the alarm. Press
this icon to cancel the alarm.
Table 2: Arming Screen Icons
*
Depicts monitored door status. A green check
indicates all monitored doors are closed. A red
exclamation point indicates one or more doors
are open.
*
*
Depicts monitored window status. A green check
indicates all monitored windows are closed. A
red exclamation point indicates one or more
windows are open.
Description
Doors & Windows
Only
This option activates perimeter sensor only.
Motion Sensors Only
This option activates interior sensors only.
Note: Depending on your configuration, this
option may not appear.
Arm All
This option activates all sensors.
Note: You will see icons at the top of the screen depicting the current
state of your installed sensors.
Optional arming choices
*
*
Icon
Depicts motions sensor status. A green check
indicates no recent motion detected. A red
exclamation point indicates motion was detected
in the last 10 minutes.
These settings are optional (for more advanced arming
features).
•
Silent exit. Press this icon to silence your exit beeps
during arming. (Your exit time will double).
•
Entry delay. Press this icon to set your entrance timer to
*
*
*
Depicts other changes to protected property in
your system. A green check indicates all sensors
are closed and no activity since you last
checked. A red exclamation point indicates
either a sensor is tripped, or there is
unacknowledged activity.
zero. (Use the No Delay feature when you are asleep, or
when you are away from home and will carry a wireless
touchpad that allows you to disarm the system before
opening a protected door). If you select the No Delay
Press this icon to access the Arming Screen.
option,
(clock with a red strike through) will appear
over the lock when the system is armed.
One of these icons will display depending on
your arming level. Press to turn off
intrusion/burglary protection for your system.
Only intrusion/burglary sensors are disarmed.
Environmental sensors, such as smoke and
carbon monoxide detectors, stay active at all
times. Enter your code in the keypad screen that
appears. If you enter an incorrect code, press
the Clear icon and enter the correct code.
Arming errors
If you select an arming option on the Arm screen, and there is
an arming problem, an arming error message screen will
appear, indicating what the problem is and how to correct it.
For example, you might see a message that indicates that you
need to close the front door.
Press to access the Status & Settings screen.
Note: * Pressing the above sensor icons will open a new screen to
provide more detail. These icons may contain the text “N/A” which
indicates your system is not configured to support this feature. Consult
your dealer for additional information.
Correct the problem as indicated or press Bypass. You will see
the arming countdown message at the bottom of the screen.
You can touch Cancel and enter your code to stop the arming
process.
Arming Screen
When you touch the PRESS TO ARM icon on the Home
screen, the Arm screen appears with the following arming
choices:
2
Simon® XTi Quick Operation Guide
Status & Settings Screen
Item
Description
To access the Status & Settings screen, press
on the
Home Screen. Refer to Table 3 below for more information on
Status & Settings screen options.
Default screen
Use this feature to set this panel’s screen
saver mode. Select “Blank” to have the screen
go dark after a period of inactivity. Otherwise,
the default will be the Home screen and the
screen will be lit. If AC power is lost, the
screen will go blank after 2 minutes of inactivity
to maximize battery life. The green AC power
icon will blink.
Note: The screen will automatically go blank at
2:00 am daily for 60 minutes.
Calibration
Press the Show icon to enter the calibration
screen. This screen will allow you to
recalibrate the touch screen.
Help
Press the Help icon to access the Help menu.
Set Date/Time
Press ENTER next to Set Date/Time to set the
date and time. (A valid master code is
required.)
System Tests
Press ENTER next to System Tests to access
Sensor Test, Comm Test, and System
Download options. (A valid master code is
required.)
Programming
Press the Show icon to view system events
Note: If a # appears in the Event History list,
the event was not sent to the central station.
Press ENTER next to Programming to access
the programming menu. (A valid master code
is required.)
Version
Displays the system’s firmware version, touch
screen version and copyright information.
Press the Select icon to enter the sensor
bypass screen. Sensor can only be bypassed
if actively armed.
To set the time
A gold icon indicates an option is selected.
A blue icon indicates an option is not selected.
Table 3: Status & Settings screen options
Item
Description
Depicts the status of the AC power and backup
battery. A red power cord represents loss of
AC power to the system. A green power cord
icon represents AC power to the system. A red
battery icon represents a low battery charge. A
green battery icon represents a fully charged
battery.
Note: These icons only appear on the main
screen if the backup battery is not fully
charged or AC power is not working correctly.
It is recommended that the backup battery be
replaced every 3-5 years. Contact your
installer to replace the backup battery.
Event History
Direct Bypass
1.
From the Status & Settings screen, select Set Date/Time.
2.
Enter access code.
Press the On/Off icon to set the chime feature
On/Off.
Note: This option may or may not appear
depending on panel programming.
3.
From the Set Date/Time screen press the first box to set
hour and press SAVE.
4.
Press the second box to set minutes and press SAVE.
Special Chime
Press the On/Off icon to set the special chime
feature On/Off.
Note: This option may or may not appear
depending on panel programming.
5.
Press a.m/p.m. box to toggle a.m/p.m. setting.
Lights
Optional. Ask your dealer for more
information.
Note: Has not been investigated by UL.
Door Locks
Optional. Ask your dealer for more
information.
Note: Has not been investigated by UL.
Voice Volume
Press the arrows to adjust the speech volume
level.
Beep Volume
Press the arrows to adjust the beep volume
level.
To set the date
Brightness
Press the arrows to adjust the screen’s
brightness.
1.
From the Set Date/Time screen press the first box in the
second row to set the month and press SAVE.
2.
Press the second box to set the day and press SAVE.
3.
Press the third box and enter the year and press SAVE.
4.
Press CLOSE repeatedly to exit.
Panel Status
Chime
Press the Listen icon to listen to the status of
your security system. Press Clear to clear the
status.
Simon® XTi Quick Operation Guide
3
Emergency icon
Unvacated premises
In an emergency, touch the Emergency icon. An Emergency
screen appears (see Emergency icon in Table 1 on page 1).
You will see three icons (Panic, Police, or Fire). Select the
appropriate icon.
Unvacated premises is a feature that determines whether the
system automatically arms down to level 2 (doors and
windows) if you arm the system to level 4 (doors, windows, and
motion sensors) without opening or closing a perimeter door
(on), or remains at the armed level chosen (off). This feature
does not work from a key fob. Autobypass must be on for this
feature to work. Check with your installer to see how these
options are programmed for your system.
Note: If your system is connected to a security monitoring
service, the authorities will be notified. This option may not be
enabled. Contact your dealer for details.
If you initiate an emergency alarm by mistake, you can cancel
the alarm by touching the red Alarm icon and entering your
code within 30 seconds (typical time limit, contact your dealer
for more information on your system configuration).
Fire alarm verification
If this option is off, the panel immediately reports to the central
station when a smoke detector goes into alarm.
With this option on, if a single smoke detector goes into alarm,
the panel will not report for 60 seconds unless another smoke
detector goes into alarm. If the first smoke detector is cleared
of an alarm within the first 60 seconds, no report will be sent to
the central station unless it or a second smoke detector goes
into alarm within the panel siren timeout period (5 minutes).
Ask your installer how this option is programmed.
Swinger Shutdown
This setting determines if a sensor or zone will go into alarm
only once during an arming period (an active arming level) and
will not be active again until the alarm is canceled (Swinger
Shutdown is enabled) or the sensor or zone will always be
active and will go into alarm multiple times during an arming
period (an active arming level) without canceling the alarm
(Swinger Shutdown is disabled).
Note: Swinger Shutdown does not affect Smoke, Fire, Carbon
Monoxide and Environmental sensors.
Ask your installer how this option is programmed and have
them explain how it will affect your system operation.
Exit/entry delay
®
Arming and disarming
Your Simon XTi provides a delay after entering or exiting your
home before the system is armed or disarmed.
Use the steps below to arm and disarm your system:
Exit delay extension
To disarm:
1.
Press PRESS TO DISARM.
2.
Enter your code when the keypad screen appears. If you
enter an incorrect code, press the Clear icon and enter the
correct code.
Note: You have four seconds between number presses to
enter the code or you will be returned to the home screen.
If enabled by your installer, the exit delay extension feature will
recognize when you arm the system, leave your house and
then quickly reenter (for example, if you forget your car keys).
If this happens, the system will restart your exit delay to give
you the full exit delay again.
Ask your installer how this option is programmed.
Alarms
To arm Doors and Windows Only, Motion Sensors Only, or
Arm All:
1.
Press PRESS TO ARM.
2.
Press DOORS & WINDOWS ONLY, MOTION SENSORS
ONLY, or ARM ALL.
3.
If a code is required, enter your code when the keypad
screen appears.
The panel starts an exit delay and sounds exit beeps until the
exit delay expires (see Table 4 on page 5).
4
The system provides annunciation to indicate an alarm
condition. When an alarm is active, the home screen will
display the alarm status (see Table 1 on page 1).
To cancel the alarm
•
If you would like to hear additional alarm information,
press Listen.
•
To cancel the alarm, press the red alarm icon and enter a
valid master or user code.
After alarms are canceled, the system will be disarmed.
Simon® XTi Quick Operation Guide
System status
Alarm sirens
In the Status & Settings screen, press Listen (no code is
required) to cause the system to speak the following types of
information:
Exterior and interior sirens make three different alarm sounds
on the premises, each indicating a different type of alarm.
Sirens are programmed by the installer to time out and stop
sounding after a specified time.
•
•
•
•
•
Alarm conditions
Alarm history
Trouble conditions
Open sensors
Bypassed sensors
The
and
icons appear when abnormal conditions
such as a trouble or open sensor exists in the system.
You can clear certain status entries from the system (such as
old alarm history) by listening to the message or by pressing
Clear next to Panel Status in the Status & Settings screen.
Table 5 below describes the siren sounds used by the security
system.
Table 5: Siren sounds
Function
Fire
Intrusion
Emergency
Interior and
panel siren
Temporal 3
Steady
Fast on/off
Exterior siren
Temporal 3
Steady
Note: Temporal 3 refers to a continuous pattern of three siren
pulses, then off for 1.5 seconds, three siren pulses, then off for
1.5 seconds.
Touchpads and key fobs
You can use touchpads and key fobs to control the security
system from remote locations in and near your home.
Interfacing with the system using a touchpad is similar to using
the panel.
Status beeps
The panel sounds status beeps to alert you to various system
events and conditions as shown in Table 4 below.
Trouble beeps
Your security system is able to automatically test itself for:
•
•
•
•
Power failures
Low batteries
Sensor supervision
Communication trouble with the central monitoring station
Activity
Beep response
When your system detects one of the problems above, six
rapid beeps sound every minute until the trouble condition is
corrected. To stop the trouble beeps, enter the Status &
Settings screen and press Listen. Trouble beeps will resume 4
hours later unless the trouble condition is corrected.
Doors+Windows
Exit delay and entry delay beeps sound two times
every 5 seconds and two times per second during
the last 10 seconds.
Programming
Table 4: Status beeps
®
Motions
Exit delay and entry delay beeps sound three times
every 5 seconds and three times per second during
the last 10 seconds.
Your Simon XTi security system allows you to program
certain user options, such as access codes.
Doors+Windows
and Motions
Exit delay and entry delay beeps sound four times
every 5 seconds and four times per second during
the last 10 seconds.
To enter programming mode:
Disarm
One beep.
Chime
Two beeps.
Special chime
Three beeps.
Property/asset
management
One beep. (Information displays only on the TwoWay Talking Touch Screen).
Trouble beeps
Six beeps every minute. Press Listen next to Panel
Status to stop beeps for 4 hours.
1.
From the Status & Settings screen, scroll down to the
Programming option and press Enter.
2.
Enter the access code and press OK.
Access codes
No activity
beeps
Twenty beeps every minute for 5 minutes (feature
must be programmed by the installer).
Simon® XTi Quick Operation Guide
To add/edit access codes:
1.
From the Programming screen, press ACCESS CODES.
2.
To add or edit an access code, press the white field next
to the access code.
3.
Enter the new/edited code on the numbered keypad and
press SAVE.
5
4.
Press CLOSE repeatedly to exit menus.
Chimes
Use the chime feature to signal when a protected door is
opened while the system is disarmed. The panel chimes when
a chime sensor is tripped, if the chime mode is enabled. This
feature allows you to be notified when family members are
going in and out of your home. The chime feature is turned on
or off in the Status & Settings screen.
kitchen, the motion sensor in the kitchen is tripped, sounding a
local alarm. If motion is detected by the living room motion
sensor within two minutes, an alarm report will be sent to the
central station.
Figure 1: Cross-zone diagram
Note: If there are no chime sensors in your system, you will
not be able to enable the chime feature.
Your installer may have programmed the system to speak the
sensor name or make a custom chime sound when a chime
sensor is tripped. The chime sound, if programmed, will be
played in place of the standard chime beeps.
To enable or disable the chime feature:
1.
Open the Status & Settings screen. The gold icon
indicates an option is selected.
2.
To change the value, press On or Off next to Chime
(depending on the settings your installer programmed, it
may not be possible to turn on the feature).
3.
Press Close to exit.
Special chime
The special chime feature allows you to install motion sensors
in a patio or at the front door, and be notified when someone is
approaching those areas. These motion sensors are not used
for intrusion protection. The panel will chime, if the special
chime mode is enabled.
Note: If there are no special chime sensors in your system, the
special chime option will not appear in the Status & Settings
screen.
System tests
Sensor test
You should test sensors one at a time to make sure they are
sending strong signals to the panel. You should test the
sensors at least once a week.
To perform the sensor test:
1.
Enter the Status & Settings menu.
2.
Scroll until System Tests is listed, Press Enter.
3.
Enter your master code and press OK.
4.
Press Sensor Test. All sensors learned into your system
will be listed
5.
Test any sensor you want by tripping the sensor (see
Table 6 below for details on how to trip each device).
6.
The display will update with the total number of packets
received from each individual sensor (see Table 6 below
for minimum number of packets required).
To enable or disable the special chime feature:
1.
2.
3.
Open the Status & Settings screen. Scroll down until you
find the Special Chime feature. The gold icon indicates an
option is selected.
To change the value, press On or Off next to Special
Chime.
Press Status to exit.
Table 6: Tripping sensors for sensor test
Sensor
Instructions
Minimum
packets
required
Hardwire
contact
Open the hardwire contact.
1
Door/window
Open the secured door or
window.
6 of 8
Carbon
monoxide alarm
Press and hold the Test/Hush
button (approximately 5
seconds) until the unit beeps
two times, and then release the
button.
6 of 8
Cross-zoning
Cross zoning (two-trip) refers to two different motion sensors
that must be tripped within two minutes of each other to report
an alarm to the central station. The Cross-zoning figure shows
the path of a person walking from the kitchen to the living
room. When the person is detected walking through the
6
a
Simon® XTi Quick Operation Guide
Sensor
Instructions
Minimum
packets
required
Glassbreak a
Test with an appropriate glass
break sensor tester.
6 of 8
Motion sensor
Avoid the motion sensor field of
view for 5 minutes, and then
enter its view.
6 of 8
Press and hold the test button
until the system sounds
transmission beeps.
6 of 8
Key fob
Press and hold the Lock and
Unlock buttons simultaneously
for 3 seconds.
6 of 8
Simon XT
talking
touch screen a
For sensor testing a 1.0. touch
screen, press and hold the
Emergency icon for 5 seconds.
For sensor testing a 1.1 or
greater touch screen, press the
Settings (gear) icon, scroll
down, and then press the RF
Test icon.
6 of 8
Smoke
a.
Not investigated for use by UL.
Note: Refer to specific sensor installation instructions for
complete operation and testing details.
Sensor testing notes
•
Conduct sensor test in all possible environmental
conditions (For example: interior doors open and closed,
HVAC system on and off, wireless music system turned on
and off).
Conduct sensor test whenever changes are made to the
installation environment that may impact RF performance
(For example: mirrors installed, metal backed wall paper,
addition of other RF equipment).
If a sensor doesn’t meet minimum packet requirements,
contact your installer.
Central station communication
After performing sensor tests, check that the system is
reporting alarms successfully to the central station.
To test communication with the central station:
1.
Call the central station and tell the operator that you will be
testing the system.
2.
Arm the system.
3.
Test an emergency panic icon and trip at least one sensor
of each type (fire, intrusion, etc.) to verify that the
appropriate alarms are working correctly. There could be a
30 second delay on intrusion devices.
4.
When you finish testing the system, call the central station
to verify that the alarms were received.
Note: If your system is not connected to a central monitoring
station you won’t be able to perform the communication test.
Emergency planning
Since an emergency is always unexpected, you should
develop plans to help prepare for a variety of emergencies.
Periodically discuss and rehearse emergency plans to include
the following:
•
Understand how to use your security system.
•
Know the normal state of doors and windows: open,
closed, or locked.
•
Escape fast! (Do not stop to pack).
•
Use a different escape route if closed doors feel hot to the
touch.
•
Crawl and hold your breath as much as possible to help
reduce smoke inhalation during your escape.
Comm test
•
Meet at a designated outdoor location.
The comm test is used to check proper communication.
•
Note: If Comm Test is not finished, it will continue to run even
if you exit program mode.
Emphasize that no one should return to the premises if
there is a fire.
•
Notify the fire department from a neighbor’s phone.
•
Emphasize that no one should enter the premises if they
hear sirens in the house.
•
If you arrive at the premises and hear sirens, do no enter.
Call for emergency assistance with your cell phone, or
from a neighbor’s phone.
•
•
To perform a comm test:
1.
Enter the Status & Settings menu.
2.
Scroll until System Tests is listed, Press Enter.
3.
Enter your master code and press OK.
4.
Press Comm Test.
The panel displays if the comm test was successful or not.
Simon® XTi Quick Operation Guide
7
Smoke Detector Placement
Your floor plan
Use the following guidelines when drawing your floor plan:
Cleaning the touch screen
•
Show all building levels.
If necessary, use a soft cloth to clear smudges on the touch
screen; do not use glass cleaner on the touch screen.
•
Show exits from each room (two per room are
recommended).
Disposal
•
Show the location of all security system components.
•
Show the location of any fire extinguishers.
8
Dispose of all equipment is accordance with local
requirements. Contact your installer for more information.
Simon® XTi Quick Operation Guide
Support
Warranty Information
There may be additional features or programming options for
your system depending on how it was installed. Contact your
dealer or UTC Fire & Security for more information.
MANUFACTURER HEREBY DISCLAIMS ALL WARRANTIES
AND REPRESENTATIONS, WHETHER EXPRESS, IMPLIED,
STATUTORY OR OTHERWISE INCLUDING (BUT NOT
LIMITED TO) ANY WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE WITH
RESPECT TO ITS CONCORD 4 PRODUCTS AND RELATED
SOFTWARE. MANUFACTURER FURTHER DISCLAIMS ANY
OTHER IMPLIED WARRANTY UNDER THE UNIFORM
COMPUTER INFORMATION TRANSACTIONS ACT OR
SIMILAR LAW AS ENACTED BY ANY STATE.
FCC compliance
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a residential environment. This equipment
generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
FCC Part 15 registration number: B4Z-910C-SIMON
IC: 1175C-910CSIMO
(USA only) SOME STATES DO NOT ALLOW THE
EXCLUSION OF IMPLIED WARRANTIES, SO THE ABOVE
EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY
ALSO HAVE OTHER LEGAL RIGHTS THAT VARY FROM
STATE TO STATE.
MANUFACTURER MAKES NO REPRESENTATION,
WARRANTY, COVENANT OR PROMISE THAT ITS
SECURITY PRODUCTS AND/OR RELATED SOFTWARE (I)
WILL NOT BE HACKED, COMPROMISED AND/OR
CIRCUMVENTED; (II) WILL PREVENT, OR PROVIDE
ADEQUATE WARNING OR PROTECTION FROM, BREAKINS, BURGLARY, ROBBERY, FIRE; OR (III) WILL WORK
PROPERLY IN ALL ENVIRONMENTS AND APPLICATIONS.
Part 68. This equipment complies with Part 68 of the FCC rules
and the requirements adopted by the ACTA.
FCC registration number: US: B4ZAK02B55910
Canada: 1175C-910CSIXT
Ringer Equivalence 0.2B
Load Number 0.2
Contact information
www.utcfireandsecurity.com or www.interlogix.com
For customer support, see www.interlogix.com/contact
All trademarks are the property of their respective owners.
Interlogix is part of UTC Climate, Controls & Security, a unit of
United Technologies Corporation.
© 2016 United Technologies Corporation. All rights reserved
Simon® XTi Quick Operation Guide
9
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising