Walk-Behind Scarifer

Walk-Behind Scarifer
CPL8-CPM-4-8-10-I-0416
EQUIPMENT DEVELOPMENT CO., INC.
Operator’s Instruction Manual
Walk-Behind Scarifer
Models CPL-8, CPM-4, 8 & 10
CPM-4
CPL-8
CPM-8
CPM-10
Gasoline/Electric
Concrete/Asphalt Planer
EQUIPMENT DEVELOPMENT CO., INC.
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone: 301-638-3326 • 301-663-1600
Page 1
Fax: 800-447-3326 • 301-663-1607
edcoinc.com • sales@edcoinc.com
CPL8-CPM-4-8-10-I-0416
READ AND UNDERSTAND THE OPERATORS INSTRUCTION MANUAL THOROUGHLY
BEFORE ATTEMPTING TO OPERATE THIS EQUIPMENT.
Death or serious injury could occur if this machine is used improperly.
SAFETY
MESSAGES
EQUIPMENT DEVELOPMENT
CO., INC.power by pulling cord. To disconnect, grasp
• Do not disconnect
SAFETY MESSAGES
• Safety Instructions are proceeded by a graphic alert symbol
of DANGER, WARNING, or CAUTION.
Indicates an imminent hazard which, if not
avoided, will result in death or serious injury.
Indicates an imminent hazard which, if not
avoided, can result in death or serious injury.
Indicates hazards which, if not avoided, could
result in serious injury and or damage to the
equipment.
GASOLINE/PROPANE POWERED EQUIPMENT
• Engine exhaust from this product contains
chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm.
• Gasoline is extremely flammable and poisonous.
It should only be dispensed in well ventilated areas,
and with a cool engine.
• Small gasoline engines produce high concentrations of carbon monoxide (CO) example: a 5 HP 4 cycle
engine operation in an enclosed 100,000 cu. ft. area with
only one change of air per hour is capable of providing
deadly concentrations of CO in less than fifteen minutes.
Five changes of air in the same area will produce noxious
fumes in less than 30 minutes. Gasoline or propane powered equipment should not be used in enclosed or partially
enclosed areas. Symptoms of CO poisoning include, headache, nausea, weakness, dizziness, visual problems and
loss of consciousness. If symptoms occur - get into fresh
air and seek medical attention immediately.
ELECTRICAL POWERED EQUIPMENT
•
•
•
•
Extreme care must be taken when operating electric
models with water present: Ensure power cord is properly grounded, is attached to a Ground-Fault-Interrupter
(GFI) outlet, and is undamaged.
Check all electrical cables - be sure connections are tight and
cable is continuous and in good condition. Be sure cable is
correctly rated for both the operating current and voltage of
this equipment.
Improper connection of the equipment-grounding conductor can
result in a risk of electric shock. Check with qualified electrician or service person if there is any doubt as to whether the
outlet is properly grounded. Adhere to all local codes and
ordinances.
NOTE: In the event of a malfunction or breakdown, grounding
provides a path of least resistance for the electric current to
dissipate. The motor is equipped with a grounded plug and
must be connected to an outlet that is properly installed and
properly grounded. DO NOT modify the plug provided on the
motor. If the plug does not fit the outlet have a qualified electrician install the proper receptacle.
Switch motor OFF before disconnecting power.
the plug, not the cord.
• Unplug power cord at the machine when not in use and before
servicing.
GENERAL INSTRUCTIONS
• Equipment should only be operated by trained personnel in
good physical condition and mental health (not fatigued). The
operator and maintenance personnel must be physically able
to handle the bulk weight and power of this equipment.
• This is a one person tool. Maintain a safe operating distance
to other personnel. It is the operators’ responsibility to keep
other people (workers, pedestrians, bystanders, etc.) away
during operation. Block off the work area in all directions with
roping, safety netting, etc. for a safe distance. Failure to do so
may result in others being injured by flying debris or exposing
them to harmful dust and noise.
• This equipment is intended for commercial use only.
• For the operator’s safety and the safety of others, always keep
all guards in place during operation.
• Never let equipment run unattended.
• Personal Protection Equipment and proper safety attire must
be worn when operating this machinery. The operator must
wear approved safety equipment appropriate for the job such
as hard hat and safety shoes when conditions require. Hearing protection MUST be used (operational noise levels of this
equipment may exceed 85db). Eye protection MUST be worn
at all times.
Keep body parts and loose clothing away from moving
parts. Failure to do so could result in dismemberment
or death.
• Do not modify the machine.
• Stop motor/engine when adjusting or servicing this equipment.
Maintain a safe operating distance from flammable
materials. Sparks from the cutting-action of this machine
can ignite flammable materials or vapors.
DUST WARNING
Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities contains chemicals known to cause cancer,
birth defects, or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints, and
• Crystalline silica from bricks and concrete and other
masonry products.
Your risk of exposure to these chemicals varies depending
on how often you do this type of work. To reduce your risk:
work in a well ventilated area, use a dust control system, such
as an industrial-style vacuum, and wear approved personal
safety equipment, such as a dust/particle respirator designed
to filter out microscopic particles.
Page 2
800-638-3326 • edcoinc.com • sales@edcoinc.com
CPL8-CPM-4-8-10-I-0416
Equipment Instruction Manual
EDCO Models CPL-8, CPM-4, CPM-8, CPM-10
EQUIPMENT
DEVELOPMENT
CO., INC.
Table
of Contents
Section
Page Number
Safety Messages.................................................................................................................................. 2
Table of Contents and Specifications................................................................................................... 3
Safety Guidelines................................................................................................................................. 4-5
Operating Instructions.......................................................................................................................... 5-9
Cutting, Drum Removal/Replacement.............................................................................................. 10-12
Dry Planing........................................................................................................................................... 13
What to expect from your EDCO product......................................................................................... 14-15
SMI Dust and Silica Warning................................................................................................................ 16
Maintenance Instructions, Maintenance Schedule........................................................................... 17-19
Limited Equipment Warranty.................................................................................................. back cover
Height
Length
Width
CPM-10 Shown
Figure 1
Specifications and dimensions are
approximate and subject to change.
HOW TO ORDER REPAIR PARTS
To insure product safety and reliability, always use genuine
EDCO replacement parts when making repairs to the equipment.
CPM-4
CPM-8
CPM-10
CPL-8
Length 46”/117cm
35”/89cm
42”/107cm
31.25”/99.4cm
17”/43cm
19”/47cm
23”/58cm
19”/47cm
40”/101cm
41”/104cm
42.5”/108cm
Model
When ordering parts, please specify the MODEL and SERIAL
NUMBER of the machine as given on the NAMEPLATE. In
addition, give part number, description and quantity as listed
on the parts list.
Please note: Due to improvements and changes in the equipment the illustrations shown may be different from the actual
machine.
Height 38.5”/98cm
Toll Free: Phone 1-800-638-3326 • Fax 1-800-447-3326
Width
Weight 185lbs/84kg 214lbs/97kg 270lbs/123kg 153lbs/69kg
Page 3
800-638-3326 • edcoinc.com • sales@edcoinc.com
CPL8-CPM-4-8-10-I-0416
Read and understand the Operator’s Manual,
and the Engine/Motor Manufacturer’s Owner’s Manual
before operating
this equipment.
EQUIPMENT
DEVELOPMENT
CO., INC.
Death or serious injury can result if this machine is used improperly.
Safety Guidelines
Eye and ear protection must be worn at all times when this machine is in use. During normal use,
sound levels exceed 85dB. Use only ANSI approved safety glasses to help prevent eye injury. Everyday eyeglasses have only impact resistant lenses; they are NOT safety glasses.
Operator must wear appropriate clothing and footwear. Do not wear loose clothing or jewelry that can get
tangled or caught in moving parts. Steel toe safety shoes should be worn.
•
Maintain the machine in safe operating condition with all guards in place and secure, all mechanical fasteners
tight, all controls in working order and the machine configured for the job application. Be sure all safety decals can
be clearly read and understood. Replace damaged or missing decals immediately.
•
The CPL-8, CPM-4-8 & 10 Planers are designed to plane flat, horizontal concrete or asphalt slabs. They
may be called Planers, Mills, Grinders or Scarifiers and may be equipped with gasoline, propane engines or
electric motors. They are designed to be operated by a single operator from a position at the rear of the equipment.
•
Keep a safe operating distance to other personnel in the area and never leave the machine running unattended.
•
Avoid deck inserts, pipes, columns, openings, electrical outlets, or any objects protruding from slab surface.
•
Never operate this machine while under the influence of drugs, alcohol or when taking medications that impair the senses or reactions, or when excessively tired or under stress.
For Electric Models:
Electric motors must be properly grounded at all times. Check the outlet box to be sure the electrical
service is properly grounded. Be sure adequate power is available. Insufficient power will cause a
motor to overheat and burn out. Use only grounded extension cords correctly sized for the current
draw and voltage drop (amp rating and length). Never use frayed, damaged, taped or under rated
extension cords. Electrical shock could result in death or serious injury to the operator and damage to
the equipment.
NOTE: On 5HP, single-phase, turn rotary power switch to the OFF position before pressing the
manual reset button on the motor. On 3 phase push button on control box before pressing reset on
the motor. Failure to do so could cause bodily harm and damage to the machine and/or work surface.
IMPORTANT NOTE:
Make sure the ON/OFF power switch is in the OFF
position before pressing the reset button on the motor.
Failure to do so could cause bodily harm and damage to
the machine and/or work surface.
IMPORTANT NOTE:
Make sure the ON/OFF power switch is in the OFF
position before pressing the reset button on the motor.
Failure to do so could cause bodily harm and damage to
the machine and/or work surface.
Page 4
800-638-3326 • edcoinc.com • sales@edcoinc.com
CPL8-CPM-4-8-10-I-0416
For Gasoline or Propane Models:
Poisonous exhaust gas. Do not operate gasoline or propane powered equipment without adequate
ventilation. Carbon monoxide is an invisible, odorless gas that can kill. NEVER REFUEL A HOT
ENGINE OR AN ENGINE WHILE IT IS RUNNING. Only refuel a cool “stopped” engine in a well
EQUIPMENT
DEVELOPMENT
INC.
ventiated area. Properly
clean any spilled
fuel before CO.,
starting
the engine.
Safety warnings and guidelines do not by themselves eliminate danger.
They are not given as substitutes for proper accident prevention and good judgement.
Operating Instructions
1. Cutter Head Lever
2. Depth Control Knob
3. Emergency Stop Tether (CPM-10)
Stop button on (CPM-4 & CPM-8) *
4. Cushioned Handles
5. Ignition Switch (Position will vary) *
6. Throttle Control *
7. Water Hook Up
8. Fuel Tank *
9. Emergency Stop Switch Lanyard
(CPM-10) *
10. Easy Lift Handle
11. Fuel Lockoff Solenoid Toggle
For Propane Models Only.
(Not Shown) *
* Not on Electric models
NOTE: Controls are similar on all models.
5
8
5
1
10
2
3
6
4
4
9
7
Figure 2
Page 5
800-638-3326 • edcoinc.com • sales@edcoinc.com
CPL8-CPM-4-8-10-I-0416
CPL8, CPM-4-8-10 OPERATING INSTRUCTIONS
When using Hi-carbon
steelDEVELOPMENT
or Tungsten
cutter wheels:
EQUIPMENT
CO.,Carbide
INC.
IMPORTANT!
Read the engine manufacturer’s manual, familiarize yourself with engine start procedures.
BEFORE STARTING THE ENGINE:
*Gasoline models only
Be sure that the cutter drum assembly has been properly installed and the cutter
drum shaft is in place and secured.
1. Select a level place at the job site. Set the “disengage lever” in the full DOWN
position. Refer to (Figure A).
It is most important to determine the position of the cutter wheels as they relate to
the slab or floor surface. If the drum assembly is filled with cutters, the cutter
wheels will most likely contact the slab when the “disengage lever” is lowered.
Refer to (Figure B).
Turn the “depth adjustment crank” UP until the cutter wheels are clear of the slab.
Refer to (Figure A). Follow these instructions each time before the engine is
started to prevent accidental damage to the slab.
Figure A
2. Raise the “disengage lever” to the full UP position. DO NOT force the lever. If
resistance is felt, turn the “depth adjustment crank” DOWN one or two turns.
This will allow the “disengage lever” to reach its normal full UP position. Refer to
(Figure C).
3. Check level of oil in engine crankcase (engines are usually shipped dry, oil must
be added as per engine manufacturers instructions). *
4. Check fuel level ( follow engine manufacturers instructions). *
5. Be sure all guards (belt, motor, cutter wheel) are in place and secure.
Figure B
6. Vacuum hose port should have hose attached or cap installed to control dust
generated during the cutting operation.
7. Locate engine on/off switch, if the engine is so equipped. On some engines the
throttle control is also the engine shut-off switch. Familiarize yourself with this
operation. *
8. All EDCO gasoline engine operated planers are equipped with a STOP switch,
usually located on the handle. Use this switch for emergency engine shut-off. *
9.
Cold engine starting: Be sure fuel line valve is open. Set choke (separate lever
on some engines - others have choke as part of throttle control). Open throttle
(full to engage choke) 3/4 to full on engines with a separate choke. Turn engine
ignition switch ON. Be sure emergency STOP switch is ON. *
10. Before starting determine that the recoil starter assembly turns freely, starter
rope pulls easily and the rope retracts properly. *
Figure C
Page 6
800-638-3326 • edcoinc.com • sales@edcoinc.com
CPL8-CPM-4-8-10-I-0416
Before Starting the Machine:
• Perform a visual inspection of the entire machine and all daily maintenance according to the Maintenance Schedule on page 19.
EQUIPMENT DEVELOPMENT CO., INC.
• Locate and be familiar with all engine/motor and operating controls .
• For Gasoline models, obtain the Engine Manufacturer’s Owner’s Manual. Read it and understand it before continuing. Follow the engine manual for break-in instructions.
• Use the correct cutters for the job. Be sure cutter drum is balanced, the number, size and type of cutter wheels
are correct and the cutter drum shaft is locked and secured.
• Be sure all fasteners are tight and secure, check for signs of metal cracking or fatigue, inspect for damage to
electrical wiring, damage to fuel lines, check bearings, etc.
• Be sure all guards are in place. Do not operate unless cutter drum guard is in place and secure.
• Inspect work area to determine the presence and location of deck inserts, pipes, columns and objects protruding from the slab surface so that they may be avoided during operation.
Starting the Engine/Motor:
For Electric Models:
•
•
Be sure the “ON/OFF” rotary cam switch is in “OFF” position.
•
Hook up the correct voltage/phase electrical power source by plugging into the connector provided.
If the cord does not mate with the connector, consult a qualified licensed electrician before continuing.
•
Verify that the electrical current being supplied is the proper voltage and phase required to run the equipment.
Check motor rotation. Cutter drum rotation on the model CPM machines is “down cut.” DO NOT use if drum
rotation is incorrect - have a qualified electrician make the necessary change in the main control panel or motor
connection box.
For Gasoline Models:
•
Consult the Engine Manufacturer’s Owner’s Manual and follow the directions
for starting the engine and allow the engine to warm up.
DO NOT operate gasoline/propane
powered equipment without adequate
ventilation. Carbon monoxide is an
invisible, oderless gas that can kill.
Lanyard Kill Switch (CPM-10 Only):
• The CPM-10 comes equipped with a lanyard kill switch. The operator should attach
the snap hook around his wrist or to his belt. If control of the machine is lost the hook
will pull free and release from the stop switch, immediately stopping the machine.
Page 7
800-638-3326 • edcoinc.com • sales@edcoinc.com
CPL8-CPM-4-8-10-I-0416
EQUIPMENT DEVELOPMENT CO., INC.
CUTTING
Starting the Cut:
•
Slowly lower the cutter head to the slab surface with the cutter head lever.
(Figure 2, Item 1) & (Figure 4)
•
Lift the knob of the Depth Control to unlock and turn the hand wheel slowly
until the cutter head contacts the slab (you will hear the sound of the cutter
wheels contacting the slab). Continue adjusting the depth of cut until the
desired depth is reached; max depth of cut 3/8” (9.5 mm).
•
Use an Industrial Vacuum Dust Control System for dry planing operations.
•
Optional water hookup also available.
Figure 4
To Stop Cutting:
•
Move cutter head control lever to raise cutter head assembly above slab surface.
•
For gasoline and propane models, close throttle and turn the ignition switch to the “off” position.
•
For electric models, depress the “OFF” button.
After Cutting:
•
At the end of the day, clean the entire machine after it has cooled. Check for worn or damaged cutters and perform any required maintenance. See Maintenance Schedule page 19 and Instructions on page 17.
•
If water was used for dust control - - - clean slurry under machine before it drys.
Page 8
800-638-3326 • edcoinc.com • sales@edcoinc.com
CPL8-CPM-4-8-10-I-0416
Cutting Heads / Drums:
•
Drum assembly revolves at approximately 1200-1800 R. P. M.; Model CPM-10 is a “down-cut” planer, Model
CPM-8 is a “down-cut” planer, and ScariLite-8 is a down-cut planer, Model CPM-4 is an “up-cut” planer. Depth
EQUIPMENT
DEVELOPMENT
CO.,ofINC.
of cut is completely determined by
the material to
be cut, horsepower
the engine/motor and spacing of the
cutter wheels on the cutter head.
•
All cuts should be started from a stationary position - when the cutting depth is reached the planer should then
move forward.
•
The engine/motor should not labor. Run at full speed and adjust forward speed to fit the work being performed.
Very hard concrete will have to be cut at a slower pace than asphalt or deteriorated surfaces.
• If it is necessary to make deep cuts - make several shallow cuts to achieve the desired depth. If the cutting depth
is set too deep the cutter wheels will not be able to absorb the shock and damage to the equipment will result.
• The cutter wheels have an oversized arbor hole. This “play” is needed to absorb some of the shock of the cutter
contacting the concrete and allow the cutter to “rebound” from the surface.
• Cutting speed is directly proportional to the amount of material to be removed in one pass; an example - cutters
spaced on 1” centers will penetrate to a greater depth than those spaced at 1/2” centers, and the planer will
move forward faster. Most of the material in the path of the cutting head will be removed either by the cutters
them selves or through the natural hammering action and spalling of the material being cut. A later pass with
cutters spaced closer together will remove the ridges.
To Reach Maximum Depth in Concrete:
• It is best to make several passes - increments of 1/32-1/8” or even less if surface is extremely hard.
• Use coarse (wide spacing) for initial passes. Complete job with medium spacing. Never use a fine spaced cutter
head to cut deeper than 1/32-1/8”.
• Some concrete slabs, especially if they are covered with water a good deal of the time or if they have been treated with hardeners, develop an extremely high surface strength.
• Material removal depth should not exceed 1/32-1/8” per pass thus requiring several passes to reach the desired
depth of cut.
To Cut Asphalt:
• This surface can be easier to penetrate than concrete. In some instances depths of 1/4” per pass can be
achieved with the larger machines. In general though, 1/8” per pass is still standard and should be maintained
until the hardness of the asphalt is determined.
Note: Specific information on asphalt cutting is available upon request.
Fine Cutting:
• This assembly should be used for very shallow or cleaning operations. Check with dealer for special cutter
wheels for removal of paint build-up or similar surface coatings.
Page 9
800-638-3326 • edcoinc.com • sales@edcoinc.com
CPL8-CPM-4-8-10-I-0416
CPM-4 DRUM REMOVAL / REPLACEMENT
CPM-4 and CPM-8 EDGER ATTACHMENT
EQUIPMENT DEVELOPMENT CO., INC.
To remove or replace drum assembly on the CPM-4 remove
the two (2) bolts securing the drum cover plate in the photo
on the left.
Next remove the socket head screw as shown in the photo
on the left.
Slide the drum out as shown in the photo on the left.
Reverse procedure to reassemble.
Page 10
800-638-3326 • edcoinc.com • sales@edcoinc.com
CPL8-CPM-4-8-10-I-0416
CPL-8/CPM-8 DRUM REMOVAL / REPLACEMENT
EQUIPMENT DEVELOPMENT CO., INC.
RETAINING NUTS
(LEFT-HAND THREAD)
PLASTIC
PLUG
RIGHT
WRONG
DRIVE
STUDS
DIRECTION OF
ROTATION
MAIN SHAFT
DRUM ASSEMBLY
TURN CLOCKWISE TO
REMOVE
TURN COUNTERCLOCKWISE
TO INSTALL.
1. Remove plastic plug from belt guard, set aside for later use.
2. Use a socket wrench to loosen left-hand thread retaining nuts. Be sure the socket is over the outer retaining nut
only. The outer retaining nut has to be loosened first and removed, then remove the second retaining nut. Use
drift pin to hold the other end of the shaft during this procedure.
3. Be careful not to damage threads on end of shaft when removing or installing the drum. Support the weight of the
drum to minimize the possibility of damage.
4. With the left-hand thread retaining nuts removed, use a drift pin to turn the other end of the shaft in a clockwise direction for removal. Support drum during shaft removal so the drum will not fall when the shaft is removed,
possibly causing damage to machine and personal injury.
5. Once the drum is removed, maintenance and/or cutter replacement can be performed.
6. Reverse this procedure for reassembly insuring the drive studs are lined up with drive holes in drum before inserting the main shaft. Be sure to install plastic plug removed in step #1.
Page 11
800-638-3326 • edcoinc.com • sales@edcoinc.com
CPL8-CPM-4-8-10-I-0416
CPM-10 DRUM REMOVAL / REPLACEMENT
EQUIPMENT DEVELOPMENT CO., INC.
To remove or replace the drum assembly on the CPM-10
remove the four (4) bolts circled securing the bearing plate
in the photo on the left .
NOTE: Bearing grease point.
Next remove the bearing plate as shown in the photo on the
left.
Slide the drum out as shown in the photo on the left.
Reverse procedure to reassemble.
Page 12
800-638-3326 • edcoinc.com • sales@edcoinc.com
CPL8-CPM-4-8-10-I-0416
DRY PLANING
EQUIPMENT DEVELOPMENT CO., INC.
Dry Planing:
Dry Planing creates a large volume of airborne dust. For health reasons, the
operator should wear an applicable respirator. The dust may contain chemicals
known to cause serious illnesses, including Silicosis a fatal disease of the lungs.
Check the chemical properties of the material to be removed and follow all
EPA/OSHA regulations.
Vac-200
•
An Industrial vacuum, capable of handling high volume of fine dust, such as the
VAC-200 (Figure 5), should be used when dry planing with this machine. If the material
being used is hazardous or contains Silica - the vacuum unit should be capable of
removing Respirable Silica and hazardous particles of less than 3 microns and if
necessary, have the capability to be equipped with a HEPA filter.
•
Most standard drum type units use a paper bag filter. The dust created during
planing is extremely fine and will clog the filter bag of these units and eventually
damage the vacuums motor. In addition, damage to the CPM-4-8-10 engine could
occur.
•
The collected debris and filters should be disposed of according to procedures that
comply with current EPA/OSHA standards.
Figure 5
FOR YOUR SAFETY AND WELL BEING
DO NOT operate gasoline/propane
powered equipment without adequate
ventilation. Carbon monoxide is an
invisible, oderless gas that can kill.
Page 13
800-638-3326 • edcoinc.com • sales@edcoinc.com
CPL8-CPM-4-8-10-I-0416
What to Expect from your
CPL-8 , CPM-4, CPM-8, CPM-10 EDCO Concrete Planer
EQUIPMENT DEVELOPMENT CO., INC.
The CPL-8-CPM-4-8-10 EDCO concrete Planers were
designed to remove material from the surface of concrete
slabs. The material may consist of excess concrete, coatings,
contaminants such as industrial debris, sealer, paint,
production line spill and virtually any foreign substance that
creates a safety or health hazard on walks, passageways
or floor surfaces.
Since the hardness of the surface cannot be changed
and the cutter type is limited to present state of the art
material and the power source is fixed - there may be
conditions that are beyond the capability of the planer.
To exceed these limits will only cause problems. Cutter
life will be shortened drastically, excessive vibration will
most likely cause the scarifier to self destruct.
The EDCO planers are primarily used for surface preparation
in commercial and industrial buildings. The machine’s total
weight is an advantage when used on upper floors where lbs
per sq. feet is an important factor. We have kept the overall
width to less than 36 inches (91 cm) to allow for passage
through most commercial doorways.
EDCO cannot accept responsibility if the conditions found
on the job site exceed the ability of the equipment to meet
the contractors expectations. It is the obligation of the
purchaser, user or renter to determine the compatibility
of the planer with the job to be performed.
Since the maximum depth of cut is 1/2” (2 cm) in increments
of 1/32” to 3/16”, it is not suited for removal of very hard
concrete such as the kind found on roads, bridge decks or
runways. This work is best accomplished by heavy duty
milling machines built for that purpose.
The basic mechanical structure consists of a fabricated steel
frame, a power source - electric, gasoline, or propane (an air
motor can also be adapted), and a rotating drum like cutter
head that can be raised or lowered to a chosen depth by
the operator.
The CPM-4 model is designed with an “up-cut” rotation of
the cutter drum assembly, consequently a milling type action
occurs. The CPM-8, CPM-10 and CPM-8 are down-cut
machines.
The push units require very little manual labor to operate the operator controls speed, forward and reverse directions.
Note that it will cut in forward or reverse directions.
The 4” to 10” inch wide drum assemblies consist of a welded
cage holding 4, 6 or 8 hardened shafts - locked in place during
operation and removable when replacing cutters.
Several styles and sizes of cutters are available. All types of
cutters may be used on all sizes of drum assemblies. Cutters
vary in size - 2 3/8” for light removal, 3” diameter for longer
life. Additional cutter wheel specifications can be found on
literature and price lists.
The efficiency of the planer is determined by 3 factors - the
hardness and type of surface to be removed, the type of
cutting tool and the power behind the cutters.
We at EDCO are prepared to assist the user. We can
provide technical information and comparison data
on jobs of a similar nature. Given information on the
project we can advise the contractor which tools, in our
opinion, will suit the job best, approximate production
rates and possibly arrange a demonstration or suggest
an alternative method or equipment.
EDCO concrete planers, when properly used, will perform
efficiently and economically, but as with all “demolition”
equipment, unless proper maintenance is provided they
tend to wear out faster than other mechanical devices.
It is important that each job be considered individually.
Testing should be carried out and a determination made
if the project is feasible under the circumstances. In
those instances where no other alternative is available,
various changes in procedure can be tried - shallower
cutting depth, slower forward speeds, spacing of cutters
changed - extra weight added. We do not guarantee
life of cutters, depth of cut, life of equipment (except for
workmanship). Equipment of this type is capable of self
destruction through misuse or abuse and the owner/
operator is the vital component that can mean success
or failure of the project.
Our technical information has been obtained from years
of experience on all types of job sites and we will gladly
share this information with you. New materials are
constantly being introduced - concrete is made harder
with additives, chemicals and new curing techniques. We
try to keep up with these changes, it’s a never ending job
for us and we need your cooperation to provide us with
accurate job site conditions and information.
Page 14
800-638-3326 • edcoinc.com • sales@edcoinc.com
CPL8-CPM-4-8-10-I-0416
TYPICAL DRUM SET-UPS
EQUIPMENT DEVELOPMENT CO., INC.
Surface preparation
six shaft drum CPM-4
Surface preparation six
shaft drum CPL-8
Surface preparation
eight shaft drum CPM-10
Surface preparation
six shaft drum CPM-8
Surface preparation
six shaft drum CPM-8
Grooving six shaft
drum CPM-10
Page 15
800-638-3326 • edcoinc.com • sales@edcoinc.com
CPL8-CPM-4-8-10-I-0416
SMI Dust and Silica Warning
EQUIPMENT DEVELOPMENT CO., INC.
Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust,
mists and fumes containing chemicals known to cause serious or fatal injury or illness, such
as respiratory disease, cancer, birth defects or other reproductive harm. If you are unfamiliar
with the risks associated with the particular process and/or material being cut or the composition of the tool
being used, review the material safety data sheets and/or consult your employer, the manufacturers/suppliers,
governmental agencies such as OSHA and NIOSH and other sources on hazardous materials. California and
some other authorities, for instance, have published lists of substances known to cause cancer, reproductive
toxicity, or other harmful effects.
Control dust, mist and fumes at the source where possible. In this regard use good work practices and follow
the recommendations of the manufacturers/suppliers, OSHA/NIOSH, and occupational and trade associations.
Water should be used for dust suppression when wet grinding/cutting/drilling is feasible. When the hazards from
inhalation of dust, mists and fumes cannot be eliminated, the operator and any bystanders should always wear
a respirator approved by NIOSH/MSHA for the material being used.
Grinding/cutting/drilling of masonry, concrete and other materials with silica in their composition
may give off dust or mists containing crystalline silica. Silica is a basic component of sand,
quartz, brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial
inhalation of airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis. In addition,
California and some other authorities have listed respirable crystalline silica as a substance known to cause
cancer. When grinding/cutting/drilling such materials, always follow the respiratory precautions mentioned above.
Page 16
800-638-3326 • edcoinc.com • sales@edcoinc.com
CPL8-CPM-4-8-10-I-0416
Remove spark plug lead on gasoline/propane engine models
or disconnect the supply voltage connector on
electric models before performing any maintenance.
EQUIPMENT
CO.,machine.
INC.
Disconnect
the DEVELOPMENT
power cord at the
Maintenance Instructions
Refer to the Engine/Motor Manufacturer’s Owner’s Manual
for maintenance information specific to the engine/motor used.
Never work on or under equipment without first securing the equipment to prevent it from moving or falling. Always work on a flat and level surface.
IMPORTANT!
Grease cutter assembly bearings (2 ea)
after every 4 hours of use.
Cutter assembly
bearings (2)
CPM 8 & 10
CPM-4
Depth Control
Grease point
all models. Bearing
Jacking Bolt
Manual Reset
Button
Power Switch
Depth Control
Multi Vac Port
Multi Vac Port
Grease Depth Control grease point
every 40 hours.
Wheel
CPM-8 Electric
CPL-8
Page 17
800-638-3326 • edcoinc.com • sales@edcoinc.com
CPL8-CPM-4-8-10-I-0416
CPL-8, CPM-4-8-10 MAINTENANCE INSTRUCTIONS
Important!
• Check oil level before operation. Change engine oil and filter according to engine manufacturers recommendations.
• Clean air filter element daily.
Belts:
• On new equipment, and after replacing a set of belts, they should be re-tensioned after the first four hours of use.
• New belts will be stiff and will loosen with use. Proper belt tension must be maintained to transmit the engine/motor
power to the cutting drum. Slipping belts will overheat, belt life will be shortened and the cutting speed limited.
Over tensioned belts will shorten belt and bearing life.
• Damaged, stretched or excessively worn belts should be replaced with a complete set. DO NOT mix new and used
belts, doing so will only shorten the life of new belt(s) and limit power transfer from the engine/motor to the cutting
drum. This will have a definite impact on machine efficiency and production rate.
• To tension belts, loosen motor mounting hardware slightly. Use the jacking bolt to adjust the engine/motor until the
belts are tight. Tighten the engine/motor mounting hardware.
ENGINE AIR FILTER GASOLINE/PROPANE MODELS ONLY
Engine Air Filter:
• Inspect the air filter (Figure 8) for excess dust, dirt or damage before the engine is operated. More often if operating
in a extremely dusty environment.
• Operating the engine with a damaged or dirty air filter, or
without an air filter, will allow dirt to enter the engine causing
premature engine wear which is not covered under the
engine manufacturer’s warranty.
• Follow the engine manufacturer’s procedures for keeping
filters in good condition.
Page 18
800-638-3326 • edcoinc.com • sales@edcoinc.com
Figure 8
CPL8-CPM-4-8-10-I-0416
Maintenance Schedule
X
Cutter Shaft Wear
(bushings, drum)
X
Check Cutters for
uneven wear
X
Every Cutter
Change
X
Clean Air Filter Element*
X
Clean Dust & Dirt
Off Machine
X
Change Engine Oil*
(Refer to engine manual)
X
Grease Wheel Bearings
X
Belt Tensioning
As Required
Daily
X
Check Engine Oil*
Grease Cutter
Assembly Bearings
Every 40-50 Hours
of Operation
X
Visual Inspection of
Entire Machine
Every 4 Hours
All maintenance to
be performed by
qualified
personnel.
Before Operation
Repairs are
to be done
EQUIPMENT
DEVELOPMENT CO.,Read
INC. and follow instructions
in the engine owner’s
by authorized EDCO
manual.
Dealers only.
X
New
Check Cutter Shaft
and Bushings
X
X
* Gasoline and propane models only.
Page 19
800-638-3326 • edcoinc.com • sales@edcoinc.com
CPL8-CPM-4-8-10-I-0416
LIMITED EQUIPMENT WARRANTY OF SALE - TERMS & CONDITIONS
Equipment Development Company, Inc. herein referred to as EDCO (Seller) warrants that
each new unit manufactured by EDCO to be free from defects in material and workmanship
in normal use and service for a period of (1) one year (except for the cutter drum assembly
on all model concrete/asphalt planes, in which case the warranty period shall be 90 days)
from date of shipment to the original retail or equipment rental center owner.
2. PAYMENT TERMS
Payment terms are as follows. 2% 10 days (to approved and qualified accounts). Net 30
days. This is a cash discount for invoices paid within 10 days after the invoice date, regardless of date of receipt of shipment. This is not a trade discount and will not be granted to
accounts that do not adhere to stated terms.
Accessories or equipment furnished and installed on the product by EDCO but manufactured by
others, including, but not limited to engines, motors,electrical components, transmissions etc.,
shall carry the accessory manufacturers own warranty.
*All past due accounts are subject to a late payment fee of 1.5% per month or a maximum
allowed by law if different, along with the expenses incidental to collection including reasonable attorney’s fees and costs.
EDCO will, at its option, repair or replace, at the EDCO factory or at a point designated by
EDCO, any part which shall appear to the satisfaction of EDCO inspection to have been
defective in material or workmanship.
*Seller reserves the right to hold shipments against past due accounts.
EDCO reserves the right to modify, alter and improve any part or parts
without incurring any obligation to replace any part or parts previously sold without such
modified, altered or improved part or parts.
3. FREIGHT TERMS
All shipments will be made F.O.B. shipping point as designated in these Terms and Conditions, and title shall pass at the F.O.B. point. Delivery to the initial common carrier shall
constitute delivery to the Purchaser. Any claims for loss or damage during shipment
are to be filed with carrier by the Purchaser. Seller will not assume responsibility for the
performance of the carrier.
EQUIPMENT DEVELOPMENT CO., INC.
This warranty is in lieu of and excludes all other warranties, expressed, implied, statutory,
or otherwise created under applicable law including, but not limited to the warranty of
merchantability and the warranty of fitness for a particular purpose in no event shall seller
or the manufacturer of the product be liable for special, incidental, or consequential damages, including loss of profits, whether or not caused by or resulting from the negligence
of seller and/or the manufacturer of the product unless specifically provided herein. In addition, this warranty shall not apply to any products or portions there of which have been
subjected to abuse, misuse, improper installation, maintenance, or operation, electrical
failure or abnormal conditions and to products which have been tampered with, altered,
modified, repaired, reworked by anyone not approved by seller or used in any manner
inconsistent with the provisions of the above or any instructions or specifications provided
with or for the product
FORCE MAJEURE
Seller’s obligation hereunder are subject to, and Seller shall not be held responsible for, any
delay or failure to make delivery of all or any part of the Product due to labor difficulties,
fires, casualties, accidents, acts of the elements, acts of God, transportation difficulties,
delays by a common carrier, inability to obtain Product, materials or components or qualified
labor sufficient to timely perform part of or all of the obligations contained in these terms
and conditions, governmental regulations or actions, strikes, damage to or destruction in
whole or part of manufacturing plant, riots, terrorist attacks or incidents, civil commotions,
warlike conditions, flood , tidal waves, typhoon, hurricane, earthquake, lightning, explosion
or any other causes, contingencies or circumstances within or without the United States not
subject to the Seller’s control which prevent or hinder the manufacture or delivery of the
Products or make the fulfillment of these terms and conditions impracticable. In the event
of the occurrence of any of the foregoing, at the option of Seller, Seller shall be excused
from the performance under these Terms and Conditions, or the performance of the Seller
shall be correspondingly extended.
This document sets forth the terms and conditions pursuant to which the purchaser (“Purchaser”) will purchase and Equipment Development Co.Inc. (“Seller”)will sell the products,
accessories, attachments (collectively the Products “) ordered by the Purchaser. These
terms and conditions shall govern and apply to the sale of Seller’s Products to Purchaser,
regardless of any terms and conditions appearing on any purchase order or other forms
submitted by Purchaser to Seller, or the inconsistency of any terms therein and herein.
1. PRICE
All prices set forth on any purchase order or other document are F.O.B. Sellers facility or distribution point, as may be determined by Seller (F.O.B.Point). All prices are exclusive of any
and all taxes, including, but not limited to, excise, sales, use, property or transportation taxes
related to the sale or use of the Products, now or hereafter imposed, together with all penalties
and expenses. Purchaser shall be responsible for collecting and/or paying any and all such
taxes, whether or not they are stated in any invoice for the Products. Unless otherwise specified herein, all prices are exclusive of inland transportation, freight, insurance and other costs
and expenses relating to the shipment of the Products from the F.O.B. point to Purchaser’s
facility. Any prepayment by Seller of freight insurance and other costs shall be for the account
of Purchaser and shall be repaid to Seller.
*Seller reserves the right to alter payment terms.
Back orders will be shipped in the most practical fashion with charges consistent with
our freight policy established with the original order. UPS, FED EX, MAIL or shipments
by other couriers are subject to the same terms and conditions as outlined in paragraph
#3”Freight Terms”.
4. DELIVERY, DAMAGES, SHORTAGES
Seller shall use reasonable efforts to attempt to cause the Products to be delivered as provided
for in these Terms & Conditions. Delivery to the initial common carrier shall constitute the delivery
to the Purchaser. Sellers responsibility, in so far as transportation risks are concerned ceases
upon the delivery of the Products in good condition to such carrier at the F.O.B. point and all the
Products shall be shipped at the Purchaser’s risk. Seller shall not be responsible or liable for
any loss of income and/or profits, or incidental, special, consequential damages resulting from
Seller’s delayed performance in shipment and delivery.
5. RETURN OF DEFECTIVE PRODUCTS
Defective or failed material shall be held at the Purchaser’s premises until authorization has
been granted by Seller to return or dispose of Products. Products that are to be returned
for final inspection must be returned Freight Prepaid in the most economical way. Credit
will be issued for material found to be defective upon Seller’s inspection based on prices
at time of purchase.
6. PRODUCTS ORDERED IN ERROR
Products may be returned, provided that claim is made and Seller is notified within 7 days
of receipt of Products, and the Products are in original buyer’s possession not more than
30 days prior to return, subject to Seller’s approval. If Products are accepted for return,
they must be Freight Prepaid and buyer will be charged a minimum of 15% restocking
charge, plus a charge back for outbound freight charges if the original order was shipped
prepaid. Returns are not accepted for any Products that are specifically manufactured to
meet the buyer’s requirement of either specifications or quantity.
AGREEMENTS
These Terms and Conditions constitute the entire agreement between Seller and Purchaser as
it relates to terms and conditions of sale, and supersedes any and all prior oral or written agreements, correspondence, quotations or understandings heretofore in force between the parties
relating to the subject matter hereof. There are no agreements between Seller and Purchaser
with respect to the Product herein except those specifically set forth in and made part of these
terms and conditions. Any additional terms, conditions and/or prices are rejected by Seller.
These terms and conditions may be modified, cancelled or rescinded only by a written
agreement of both parties executed by their duly authorized agents.
USE ONLY GENUINE EDCO PARTS & ACCESSORIES
For your own safety, the safety of others and the life of your machine.
Equipment Development Company, Inc.
Page 20
800-638-3326 • edcoinc.com • sales@edcoinc.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising