the growing family of Hot Spring spa owners.

the growing family of Hot Spring spa owners.
HIGHLIFE™ COLLECTION
Congratulations on your decision to enjoy the finest spa available...
Welcome to the growing family of Hot Spring spa owners.
Pre-Delivery Instructions
Please take the time to read this booklet carefully, as it will provide you with the information you will need to ensure
the safe, secure, and timely installation of your new spa. The following sections are guidelines on how to prepare for
delivery and set-up of your new spa. Specifically covered are site selection, delivery access, ground preparation, and
electrical requirements.
Remember to carefully review the Owner’s Manual that accompanies your spa, and to register the spa's warranty
within 10 days of delivery. These items, along with other valuable information, will be found in the Owner’s Package
which has been placed in the equipment compartment of your spa, where you will also find its serial number.
Watkins Manufacturing Corporation reserves the right to change features, specifications and design without
notification and without incurring any obligation.
DATE PURCHASED: _________________________________________________________________
DATE INSTALLED: ___________________________________________________________________
DEALER: ___________________________________________________________________________
ADDRESS:__________________________________________________________________________
TELEPHONE: _______________________________________________________________________
In most cities and counties, permits will be required for the installation of electrical circuits or the construction of
exterior surfaces (decks and gazebos). In addition, some communities have adopted residential barrier codes which
may require fencing and/or self-closing gates on the property to prevent unsupervised access to a pool (or spa) by
children under 5 years of age. Your Hot Spring spa is equipped with a locking cover that meets the ASTM F1346-91
Standard for Safety Covers and as a result, is usually exempt from most barrier requirements. As a general practice,
your local Building Department will inform you of any applicable barrier requirements at the time a permit is obtained
for the installation of an electrical circuit. Your Hot Spring dealer can provide information on which permits may be
required.
x
Hot Spring Spa Pre-Delivery
Page x
Instructions
x
Site Selection and Preparation
IMPORTANT: Site selection and preparation are your responsibility. Carefully read these instructions and consult
your authorized Hot Spring® dealer if you have any questions.
You probably have a spot picked out for your new spa, whether it’s indoors or outdoors, on a patio or on a deck.
Just make sure you check the following:
certain that the location you choose can support the weight of your filled spa.
Manual.)
where water will drain away from it. Allowing water into the equipment compartment can damage the
electronics, or may result in tripping your house’s circuit breaker.
switch on the end of the power cord (115 volt models).
or into the electrical outlet that your spa is plugged into. Your 115 volt Hot Spring spa will come with a
is raintight when installed correctly with the door closed.
OUTDOOR AND PATIO INSTALLATION
No matter where you install your new spa, it’s important that you have a solid foundation to support it. Structural
damage to the spa resulting from incorrect installation or placement on an inadequate foundation is not covered
under the spa’s limited warranty.
If you install the spa outdoors, a reinforced concrete pad at least four inches thick is required for the Vista® and
Grandee® spas, and recommended for the Envoy®, Vanguard®, Sovereign®, Aria ®, Prodigy® and Jetsetter® spas.
The reinforcing rod or mesh in the pad should be attached to a bond wire (see your Owner’s Manual). All Hot
Spring spas may be installed onto a deck, provided that the load capacity of the deck is greater than the
dead weight of the spa (see Deck Installation).
If you place the spa on the ground, even temporarily, place stepping stones under the leveling areas (see Spa
Leveling Instructions in your Owner’s Manual). The stones should be at least two inches thick and twelve inches
square. Even with stones in place, the spa will inevitably settle and become unlevel. Plus, a spa surrounded by
dirt or grass will soon be filled with dirt or grass from users’ feet; therefore, it is important to get it onto a solid
foundation as soon as possible.
DECK INSTALLATION
To be certain your deck can support your spa, you must know the deck’s maximum load capacity. Consult a
qualified building contractor or structural engineer before you place the spa on an elevated deck or
indoors. To find the weight of your spa, its contents and occupants, refer to the Spa Specification chart. This
weight per square foot must not exceed the structure’s rated capacity, or serious structural damage could result.
INDOOR INSTALLATION
Be aware of some special requirements if you place your spa indoors. Water will accumulate around the spa, so
flooring materials must provide a good grip when wet. Proper drainage is essential to prevent a build-up of water
around the spa. When building a new room for the spa, it is recommended that a floor drain be installed. The
humidity will naturally increase with the spa installed. Water may get into woodwork and produce dryrot, mildew,
or other problems. Check for airborne moisture’s effects on exposed wood, paper, etc. in the room. To minimize
these effects, it is best to provide plenty of ventilation to the spa area. An architect can help to determine if more
ventilation must be installed.
Your Hot Spring dealer can help you with local information such as zoning regulations and building codes.
x
Pre-Delivery
Instructions
Page x
x
DELIVERY ACCESS
First, locate the dimensions of your spa on the following chart. The
dimensions shown are the measurements of the spa in the vertical
position, laid on its side.
Next, contact your dealer to find the height and width added by
the delivery cart which the dealer will use to deliver your new
spa. Use the height of the cart plus the dimension shown as H to
determine the vertical clearance required to pass the spa and cart.
Use the width of the cart, or dimension W, whichever is greater, to
determine the maximum width of clearance necessary.
NOTE: It may be necessary to allow for additional over-head
clearance if the spa will be rolled up or down an incline or moved
up or down a short flight of stairs.
Use the information below to determine the requirements for
access to your desired location.
Model
Width W
Length L
Vista® (SS)
38”
8’ 4”
7’ 7”
Grandee ® (GG)
38”
8’ 4”
7’ 7”
Envoy ® (KK)
36”
7’ 9”
7’ 5”
Aria ® (AR)
36”
7’ 3”
7’ 3”
36”
7’ 3”
7’ 3”
33”
7’ 9”
6’ 8”
Vanguard®
(VV)
Sovereign ® (II)
Height H
Prodigy ®
Jetsetter ®
How is your width clearance?
BACK YARD
Check all gates
Protruding electric meters
Gas meters
A/C units
Do you have sufficient
overhead clearance?
Check low roof eaves,
overhanging branches,
rain gutters
HOUSE
Is the path clear?
Move away branches, dog
houses, firewood, etc.
If there is a 90 turn, can we
clear it? (The spa will not bend)
No more than 6 consecutive
stairs without a landing
x
STREET
Page 3
x
Pre-Delivery Instructions
x
It may be necessary to remove a gate, part of a fence, or other movable obstructions in order to roll the spa to its
installation site. About ten percent of the time, a crane is the only way to install the spa by lifting it to its final destination.
If the spa has to be taken off of the cart to go over a wall (either because the entry area is too narrow, the eaves are
too low, the corner is too tight, or the stairway is too steep), a crane will be required. Don’t be alarmed!
The crane has a truck-mounted boom which can fit right in your driveway. It is run by a licensed and insured
operator. For a charge, the crane operator will lift your spa over walls, buildings, or any other obstruction and place it
as close to the installation site as possible. The Hot Spring® spa delivery personnel will supervise the crane delivery
and complete the spa installation. Crane delivery typically takes an average of 30 minutes to complete.
NOTE: If your spa delivery requires the use of a crane, you may be required to pay for its services at the completion
of the delivery.
GROUND PREPARATION
Your Hot Spring spa has been engineered to perform on all kinds of
common yard surfaces. While a concrete slab is best for long-term use*,
other foundations are acceptable so long as a level base is prepared
prior to delivery. Three foundation base pictures, shown at right,
represent examples of alternatives to a concrete slab for spas installed
without gazebos or other accessories.
*NOTE: A reinforced concrete pad at least four inches thick or a deck
that is able to withstand more than 115 lbs. per square foot is required
for the Vista® and Grandee® spas , and recommended for the Envoy ®,
Vanguard®, Sovereign®, Aria ®, Prodigy ® and Jetsetter® spas.
INSTALLATION NOTES:
FOUNDATIONS FOR SPAS ONLY
(No accessories such as cover or gazebo)
PEA GRAVEL
OR CRUSHED ROCK
RAILROAD TIES
If stepping stones or railroad ties are selected for the spa
foundation, they should be placed at the designated leveling areas
of your spa to maintain even distribution of the spa weight.
It is important to note that soft surfaces, even when stepping
stones are used to distribute the weight of the spa as evenly as
possible, will still have a tendency to settle unevenly, resulting in
an unlevel spa.
Remember, placing the spa on grass or dirt may increase the
amount of debris which is inadvertently brought into the spa
water on the user’s feet.
PRE-CAST
STEPPING STONES
FOUNDATIONS FOR SPAS
WITH ACCESSORIES
If you are purchasing a deck package or a gazebo with your spa, a
solid foundation becomes mandatory. Placing them on any surface
other than a single level pad could create problems with their
installation. Pictured at right are a few of the recommended surfaces.
As a homeowner, it is your responsibility to provide a suitable, level
foundation for your spa. Keep in mind that most delivery crews are
not equipped to level and prepare spa sites.
If you are interested in having a concrete slab, brick surface, or wood
deck installed, your Hot Spring dealer should be able to suggest a
qualified, licensed contractor.
NOTE: In order for the spa to operate properly and the internal
plumbing to drain completely, you must ensure that the spa is leveled
after it has been installed. The diagrams on the following pages
indicate the recommended shimming points on your spa’s base
support system. Your Hot Spring spa delivery crew can help you
perform the procedure.
Pre-Delivery
Instructions
x
Page
Page 4
x
CONCRETE PADS
BRICK SURFACES
WOOD DECKING
x
Vista® (Model SS)
Dimensions
(Front view)
22" (56. cm)
33" (83.8 cm)
MAIN DRAIN
49" (124.5 cm)
1 3/4” (4.4 cm) ELECTRICAL CUTOUT
3 1/2" (8.9 cm)
DOOR
38" (96.5 cm)
34 1/2" (87.6 cm)
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
73 " (185.4 cm)
SECONDARY DRAIN
12" (30.5 cm)
EW
N
O
VI
W
19" (48.3 cm)
(Bottom view)
19" (48.3 cm)
F
A
SP
O
E
D
D
SI
91" (231 cm)
24 1/4" (61.6 cm)
73 1/2 " (186.7 cm)
24 1/4" (61.6 cm)
P
U
52 1/2" (133.3 cm)
42 1/2" (108 cm)
100" (254 cm)
DOOR SIDE
NOTE: Watkins Manufacturing Corporation requires that the Vista be installed on a minimum 4” thick reinforced
concrete pad or a deck that is able to withstand more than 115 lbs. per square foot.
WARNING: The Vista must not be shimmed in any manner.
x
Page 5
x
Pre-Delivery Instructions
x
Grandee® (Model GG)
Dimensions
(Front view)
22" (56. cm)
33" (83.8 cm)
MAIN DRAIN
49" (124.5 cm)
1 3/4” (4.4 cm) ELECTRICAL CUTOUT
3 1/2" (8.9 cm)
DOOR
38" (96.5 cm)
34 1/2" (87.6 cm)
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
73 " (185.4 cm)
SECONDARY DRAIN
24 1/4" (61.6 cm)
U
PS
ID
E
D
O
(Bottom view)
19" (48.3 cm)
W
N
VI
EW
O
F
19" (48.3 cm)
SP
A
12" (30.5 cm)
91" (231 cm)
24 1/4" (61.6 cm)
73 1/2 " (186.7 cm)
52 1/2" (133.3 cm)
42 1/2" (108 cm)
100" (254 cm)
DOOR SIDE
NOTE: Watkins Manufacturing Corporation requires that the Grandee be installed on a minimum 4” thick reinforced
concrete pad or a deck that is able to withstand more than 115 lbs. per square foot.
WARNING: The Grandee must not be shimmed in any manner.
x
Pre-Delivery
Instructions
Page 6
x
x
Envoy® (Model
KK)
ENVOY
Dimensions
(Front view)
16" (40.6 cm)
22 1/2" (57.1 cm)
MAIN DRAIN
43 1/2" (110.5 cm)
1 3/4” (4.4 cm) ELECTRICAL CUTOUT
3 1/2" (8.9 cm)
DOOR
36" (91.4 cm)
32 1/2" (82.5 cm)
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
67 1/2" (171.5 cm)
SECONDARY DRAIN
71" (180.3 cm)
93" (236.2 cm)
44 1/2" (113 cm)
44 1/2" (113 cm)
18" (45.7 cm)
(Bottom view)
N
O
VI
W
E
20" (50.8 cm)
O
D
D
I
PS
21 1/4" (54 cm)
U
DOOR SIDE
15 leveling points (place shims approx. 18” in from edge, then center middle shims).
x
Page 7
x
Pre-Delivery Instructions
x
89" (226.1 cm)
F
EW
A
SP
20" (50.8 cm)
22 1/4" (56.5 cm)
18" (45.7 cm)
Aria® (Model AR)
Dimensions
(Front view)
21" (53.3 cm)
MAIN DRAIN
25" (63.5 cm)
ELECTRICAL KNOCKOUT
30 3/4" (78.1 cm)
36.75" (93.3 cm)
SECONDARY DRAIN
3 1/2" (8.9 cm)
DOOR
36" (91.4 cm)
32 1/2" (82.5 cm)
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
62.0 " (157.5 cm)
12" (30.5 cm)
F
N
O
16 1/2" (42 cm)
EW
A
SP
VI
W
E
(Bottom view)
D
19" (48.3 cm)
O
ID
PS
22 1/4" (56.5 cm)
U
87" (221 cm)
24 1/4" (61.6 cm)
65 3/4" (167.0 cm)
18" (45.7 cm)
18" (45.7 cm)
41 1/2" (105.4 cm)
41 1/2" (105.4 cm)
87" (221 cm)
DOOR SIDE
15 leveling points (place shims at illustrated locations).
x
Pre-Delivery
Instructions
Page 8
x
x
Vanguard ® (Model VV)
Dimensions
32 1/2" (82.5 cm)
(Front view)
MAIN DRAIN
21" (53.3 cm)
25" (63.5 cm)
ELECTRICAL KNOCKOUT
30 3/4" (78.1 cm)
36.75" (93.3 cm)
SECONDARY DRAIN
3 1/2" (8.9 cm)
DOOR
36" (91.4 cm)
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
62.0 " (157.5 cm)
12" (30.5 cm)
F
N
O
16 1/2" (42 cm)
EW
A
SP
VI
W
E
D
19" (48.3 cm)
O
(Bottom view)
D
I
PS
22 1/4" (56.5 cm)
U
87" (221 cm)
24 1/4" (61.6 cm)
65 3/4" (167.0 cm)
18" (45.7 cm)
18" (45.7 cm)
41 1/2" (105.4 cm)
41 1/2" (105.4 cm)
87" (221 cm)
DOOR SIDE
15 leveling points (place shims at illustrated locations).
x
Page 9
x
Pre-Delivery Instructions
x
Sovereign® (Model II)
Dimensions
29 1/2" (74.9 cm)
(Front view)
17 1/2" (45.1 cm)
MAIN DRAIN
31 1/2" (80 cm)
1 3/4” (4.4 cm) ELECTRICAL CUTOUT
34.5" (67.6 cm)
58 1/2" (148.6 cm)
SECONDARY DRAIN
59 1/2" (151.1 cm)
38" (96.5 cm)
38" (96.5 cm)
18" (46 cm)
18" (46 cm)
12" (30.5 cm)
F
20" (50.8 cm)
EW
N
A
SP
O
VI
W
O
(Bottom view)
E
D
U
23 1/4" (59 cm)
20" (50.8 cm)
D
I
PS
93" (236 cm)
24 1/4" (61.6 cm)
3 1/2" (8.9 cm)
DOOR
33" (83.8 cm)
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
80" (203 cm)
DOOR
SIDE
DOOR SIDE
15 leveling points (place shims approx. 18” in from edge, then center middle shims).
x
Pre-Delivery
Instructions
Page
Page10
x
x
Prodigy ® (Model H)
Dimensions
(Front view)
13" (33 cm)
14 1/2" (36.8 cm)
MAIN DRAIN
1 3/4” (4.4 cm) ELECTRICAL CUTOUT
33 1/4" (84.5 cm)
3 1/2" (8.9 cm)
DOOR
33" (83.8 cm)
29 1/4" (74.3 cm)
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
43 1/2" (110.5 cm)
57" (144.8 cm)
SECONDARY DRAIN
74" (188 cm)
15" (38.1 cm)
12" (30.5 cm)
F
VI
W
O
E
D
19" (48.3 cm)
D
I
PS
U
23 1/4" (59.1 cm)
(Bottom view)
87" (221 cm)
N
O
19" (48.3 cm)
EW
A
SP
23 1/4" (59.1 cm)
15" (38.1 cm)
70 3/4 (179.7 cm)
DOOR SIDE
10 Leveling Points (place shims approx. 15" in from edge.)
10 leveling points (place shims approx. 15” in from edge).
Page 11
Pre-Delivery Instructions
Jetsetter ® (Model JJ)
Dimensions
1 3/4” (4.4 cm) ELECTRICAL CUTOUT
22" (55.9 cm)
28" (71.1 cm)
47" (119.4 cm)
SECONDARY DRAIN
2 1/2" (6.4 cm)
DOOR
29" (73.7 cm)
(Front view)
25 1/2" (64.8 cm)
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
58" (147.3 cm)
MAIN DRAIN
64" (162.6 cm)
84" (213.4 cm)
12" (30.5 cm)
W
IE
N
A
SP
O
V
W
O
(Bottom view)
E
D
ID
PS
15" (38.1 cm)
U
20 3/4" (52.7 cm)
19 1/4" (48.9 cm)
19 1/4" (48.9 cm)
20 3/4" (52.7 cm)
DOOR SIDE
10 leveling points (place shims approx. 15” in from edge).
Pre-Delivery Instructions
65" (165.1 cm)
F
61" (155 cm)
15" (38.1 cm)
80" (203.2 cm)
ELECTRICAL REQUIREMENTS
To ensure you will have an opportunity to use your spa soon after delivery, it is very important that the required
electrical service has been installed. Unless otherwise stipulated by your dealer, THIS IS YOUR RESPONSIBILITY.
IMPORTANT: All electrical circuits must be installed by a qualified, licensed electrician.
Hot Spring® spas are manufactured in two different electrical versions. The Vista®, Grandee®, Envoy®, Vanguard®,
Sovereign® and Aria ®
converted to 115 volt operation.
The remaining spa models, the Prodigy® and Jetsetter®
systems. These models come standard from the factory with 115 volt heating systems; however, with the addition of
115 VOLT OPERATION REQUIREMENTS
correct polarity throughout the circuit.
WIRE SPECIFICATION NOTE: Long electrical runs may require a larger gauge feed wire than stated. We
recommend that a maximum voltage drop of 3% be used when calculating the larger wire size.
NOTE: The term “dedicated” means that only the spa operates on the circuit.
Each 115 volt model comes equipped with approximately 15 feet of usable power cord. (This is the maximum length
allowed by Underwriters Laboratory.) When the spa is installed, the power cord will come out of the bottom of the
equipment compartment.
This receptacle, which contains an outdoor-rated, weather-resistant receptacle cover plate, will be provided to you.
The single receptacle and cover plate should be installed by your electrician prior to the delivery of your spa.
For your safety, when your electrician is installing the electrical outlet, it should be no closer than five (5) feet and no
farther than ten (10) feet from the spa. (Reference National Electric Code 680-6a(1) and 680-41a.)
WARNINGS: Do not connect your spa to an extension cord!
The 115 volt GFCI switch and the receptacle must be protected from weather and landscape sprinklers–they should
never get wet.
NOTE: If you require the services of a licensed electrician, your Hot Spring® Dealer should be able to suggest one
for you.
Your Hot Spring spa has been carefully engineered to provide maximum safety against electric shock. Remember,
connecting the spa to an improperly wired circuit will negate many of its safety features.
x
Page
Page13
x
Pre-Delivery Instructions
x
230 VOLT OPERATION REQUIREMENTS
spas must be wired in accordance with applicable local and national electrical codes, all
electrical work must be done by a licensed electrician.
NOTE: Watkins Manufacturing Corporation REQUIRES THE USE OF A SUBPANEL TO SUPPLY POWER AND
PROTECT THE SPA. On the Vista®, Grandee®, Envoy®, Vanguard®, Sovereign® and Aria ® models, the subpanel
® and Jetsetter®
models, the subpanel containing GFCI breakers must be purchased separately and can be purchased from your
Hot Spring dealer.
A licensed electrician should install a four-wire electrical service (two line voltages, one neutral, one ground) from
the main electrical service panel to the subpanel, and from the sub-panel to the spa per the appropriate wiring
diagram as illustrated below.
the spa but it should not be closer than five (5) feet from the spa water edge (NEC 680-38 to 41-A-3).
INSTALLATION NOTE: After the spa has been installed by the dealer’s delivery crew, your electrician can connect
®
Control Box and then complete the wiring connections in the
control box.
IMPORTANT NOTE: Three different wiring diagrams are shown: one for Vista, Grandee, Envoy, and Aria models.
One for Vanguard and Sovereign models, and one for Prodigy and Jetsetter models. Always follow the wiring
diagram for your specific model.
NOTE:
the Owner’s Manual and with each sub-panel, which can be obtained from your dealer.
WARNING: Removing or bypassing the GFCI breakers in the subpanel at any time will result in an unsafe spa and
will void the warranty.
WIRE SPECIFICATION NOTE: Long electrical runs may require a larger gauge feed wire than stated. We
recommend that a maximum voltage drop of 3% be used when calculating the larger wire size.
Vista (Model SS), Grandee (Model GG), Envoy (Model KK)
& Aria (Model AR)
WARNING! The exact physical location of the terminals
on the GFCI breaker will vary between manufacturers.
Connecting the hot wire to the neutral terminal will
cause irreversible damage to the control box.
See owner’s
manual or
control box
schematic
for electrical
connection
details.
**
GRD
System Ground Terminal
NOTE: The wire connections to GFCI breakers are for reference only. Always ensure the
white neutral wire is connected to the load neutral of the 30 amp breaker.
*PROVIDED WITH SPA.
x
Pre-Delivery
Instructions
NOTE: ALL WIRING SHOULD BE COPPER.
Page
Page14
x
x
Vanguard® (Model VV) and Sovereign® (Model II)
WARNING! The exact physical location of the terminals
on the GFCI breaker will vary between manufacturers.
Connecting the hot wire to the neutral terminal will
cause irreversible damage to the control box.
230V, 50 Amp,
2–POLE,
CIRCUIT BREAKER
(NON GFCI)
HEATER
GROUND
TB1
N
1
See owner’s
manual or
control box
schematic
for electrical
connection
details.GRD
L1
#8 AWG WHITE, NEUTRAL
GRD
#8 AWG BLUE, L1
50A
20A
#8 AWG RED, L2
2 3 4 5
L2
#10 AWG GREEN, GROUND
L2 #12 AWG RED
L1 #12 AWG BLUE
N #12 AWG WHITE
L2 #10 AWG RED
30A
L1 #10 AWG BLUE
MAIN SERVICE
ELECTRICAL
PANEL
GROUND #10 AWG GREEN
CONTROL BOX
LESS THAN 100 FT.
NOTE: The wire connections to GFCI breakers are for reference only. Always ensure the
*PROVIDED WITH SPA.
NOTE: ALL WIRING SHOULD BE COPPER.
Prodigy® (Model H) and Jetsetter® (Model JJ)
WARNING! The exact physical location of the terminals
on the GFCI breaker will vary between manufacturers.
Connecting the hot wire to the neutral terminal will
cause irreversible damage to the control box.
230V, 50 Amp,
2–POLE,
CIRCUIT BREAKER
(NON GFCI)
TB1
N
20A
#8 AWG RED, L2
L1 #12 AWG BLUE
N #12 AWG WHITE
L2 #10 AWG RED
30A
L1 #10 AWG BLUE
MAIN SERVICE
ELECTRICAL
PANEL
GROUND #10 AWG GREEN
2 3 4 5
L2
GRD
#8 AWG BLUE, L1
See owner’s
manual or
control box
schematic
for electrical
conversion
and
connection
GRD
details.
1
L1
#8 AWG WHITE, NEUTRAL
#10 AWG GREEN, GROUND
50A
HEATER
GROUND
CONTROL BOX
LESS THAN 100 FT.
NOTE: The wire connections to GFCI breakers are for reference only. Always ensure the
*AVAILABLE FROM DEALER.NOTE: ALL WIRING SHOULD BE COPPER.
x
Page
Page15
x
Pre-Delivery Instructions
x
WIRE INSTALLATION
FOR CONTROL BOX TERMINAL BLOCK
(Layout of Spa’s Terminal Blocks may vary)
Insert
screwdriver to
engage cage
clamp
3
Push top of
screwdriver away
from wire
Terminal Block
Wire Installation Steps
4
1/2”
Strip wire
insulation back
½”
Refer to spa’s wiring
diagram on back of Control
Box Cover for proper wiring
3
Entire stripped
end of wire
must be inside
Terminal
Block
Install
Stripped end
of wire into
Terminal
Block
After step 6,
pull on wire to
ensure proper
installation
Remove
screwdriver
6
5
SERVICES AVAILABLE FROM YOUR
HOT SPRING® SPA DEALER
Service
Pre-Delivery site inspection
Deliver spa to installation site
Unwrap spa and haul away packaging material
Set up & level spa
Fill the spa with water
Connect the spa to its power source (115 volt models)
Explain and test the spa’s operation
Jet system
Moto-Massage® jet
Set temperature control
Control panel functions
Explain the safety features
GFCI
Heater high limit
Cost
_____________
_____________
_____________
_____________
_____________
_____________
Comfort Control® system
Heater thermal cut-off
General spa operation & maintenance orientation
Water quality and maintenance orientation
Adjust the water’s Total Alkalinity, Calcium Hardness and pH
Sanitize the water
Inspect the spa cover, place on spa
Review winterizing instructions
Review Owner’s Manual & Warranty Card
Follow-up call
In-store spa water analysis
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
TOTAL COST
_____________
x
Pre-Delivery
Instructions
Page
Page16
x
x
ADDITIONAL PRODUCTS AVAILABLE FROM YOUR
HOT SPRING ® SPA DEALER
®
Salt Water Sanitizing System
® water care system featuring the FreshWater ® III high output ozone, MPS, and
FreshWaterAg+ Silver Ion Cartridge
™ Pre-filter
™ Calcium Remover
®,
CoverCradle II, UpRite and Lift’n Glide® systems.
Cover Cradle
UpRite - 7” Clearance required
Lift ’n Glide - 14” Clearance required
CONTRACTOR SUGGESTIONS
Electrician
Name:
Telephone:
Name:
Telephone:
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
Masonry
Name:
Telephone:
Name:
Telephone:
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
General
Name:
Telephone:
Name:
Telephone:
x
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
Page
Page17
x
Pre-Delivery Instructions
x
Vista®
(Model SS)
Seats 6
7'7" x 8'4"
38"
2.31m
x
2.54m
0.97 m
Grandee®
(Model GG)
Seats 7
7'7" x 8'4"
38"
2.31m
x
2.54m
0.97 m
Envoy®
(Model KK)
Seats 5
7'9" x 7' 5"
36"
2.36m
x
2.26m
0.91 m
Aria®
(Model AR)
Seats 5
7'3" x 7'3"
36"
2.21m
x
2.21m
0.91 m
Vanguard®
(Model VV)
Seats 6
7'3" x 7'3"
36"
2.21m
x
2.21m
0.91 m
Sovereign®
(Model II)
Seats 6
6'8" x 7'9"
33"
2.03m
x
2.36m
0.84 m
Prodigy®
(Model H)
Seats 5
6'2" x 7'3"
33"
1.88m
x
2.21m
0.84 m
Jetsetter
(Model JJ)
Seats 3
5'5" x 7'0"
29"
1.65m
x
2.13m
0.74 m
Dr
yW
eig
ht
Fil
led
We
igh
t*
De
ad
We
igh
t*
Ele
c
Re tric
qu al
ire
me
nts
Eff
Fil ectiv
ter
e
are
a
He
(W ater
att
s)
Wa
ter
Fo
Dim otprin
en t
sio
ns
He
igh
t
Spa Specifications
325**
square
feet
4,000
325**
square
feet
4,000
325**
square
feet
4,000
325
square
feet
4,000
150
square
feet
6,000
120
square
feet
6,000
90
square
feet
1,500
or
6,000
90
square
feet
500
gallons
1008
lbs.
457
kg.
6,228
lbs.
500
gallons
1,008
lbs.
6,403
lbs.
1,893 litres
457
kg.
2,904
kg.
450
gallons
875
lbs.
397
kg.
5,503
lbs.
365
gallons
789
lbs.
4,708
lbs.
1,385 litres
358
kg.
2,136
kg.
400
gallons
789
lbs.
5,175
lbs.
1,514
litres
358
kg.
2,347
kg.
355
gallons
713
lbs.
4,724
lbs.
1,344 litres
322
kg.
2,143
kg.
325
gallons
613
lbs.
4,199
lbs.
1,230 litres
278
kg.
1,905
kg.
225
gallons
450
lbs.
2,852
lbs.
852 litres
204
kg.
1,294
kg.
1,893 litres
1,703 litres
1,500
or
6,000
2,825
kg.
2,496
kg.
120
lbs. per
square
foot
230 volt, 50 amp
Single phase GFCI
protected circuit
125
lbs. per
square
foot
230 volt, 50 amp
Single phase GFCI
protected circuit
120
lbs. per
square
foot
230 volt, 50 amp
Single phase GFCI
protected circuit
120
lbs. per
square
foot
230 volt, 50 amp
Single phase GFCI
protected circuit
135
lbs. per
square
foot
230 volt, 50 amp
Single phase GFCI
protected circuit
115
lbs. per
square
foot
230 volt, 50 amp
Single phase GFCI
protected circuit
120
lbs. per
square
foot
115 volt, 20 amp
Dedicated GFCI
protected circuit or
100
lbs. per
square
foot
115 volt, 20 amp
Dedicated GFCI
protected circuit or
230 volt, 50 amp
Single phase GFCI
protected circuit
230 volt, 50 amp
Single phase GFCI
protected circuit
CAUTION: Watkins Manufacturing Corporation suggests a structural engineer or contractor be
consulted before the spa is placed on an elevated deck.
* NOTE: The “Filled weight” and “Dead weight” of the spa includes the weight of the occupants
(assuming an average occupant weight of 175 lbs).
**Effective filter area is based on 6.5 square feet actual area per filter with 10 times effectivity rating.
x
Pre-Delivery
Instructions
Page
Page18
x
x
x
Page
Page19
x
Pre-Delivery Instructions
x
WATKINS MANUFACTURING CORPORATION
©
CoverShield, EverFresh, FreshWater, Reduce, Revitalize, Refresh and The Home Relaxation Specialists are trademarks of
Watkins Manufacturing Corporation.
x
Page x
x
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising