w800bt user manual
W800BT
USER
MANUAL
Contents
1 Important safety instructions 2
Hearing Safety General information 2
2
2 Onkyo Bluetooth wireless headset 3
Box content 3
Other devices 3
Overview of your Bluetooth wireless
headset 3
3 Charge and pair your headset 4
Charge the battery 4
Pair between both sides of the
headset 5
Pair your headset with the
Bluetooth device 5
4 Use your headset 7
Connect the headset to a Bluetooth
device 7
Operate your headset 7
Wear your headset 8
5 Technical data 9
6Notice 10
Declaration of conformity 10
Disposal of your old product and
battery 10
Compliance with EMF 11
Trademarks 11
7 Frequently asked questions 12
EN
1
1 Important
safety
instructions
General information
To avoid damage or malfunction:
Caution
•• Do not expose the headset to excessive heat.
•• Do not drop your headset.
•• Headset shall not be exposed to dripping or
Hearing Safety
splashing.
•• Do not allow your headset to be submerged in
water.
•• Do not use any cleaning agents containing alcohol,
ammonia, benzene, or abrasives.
•• If cleaning is required use a soft cloth, if necessary
••
Danger
•• To avoid hearing damage, limit the time you use
headphones at high volume and set the volume to
a safe level. The louder the volume, the shorter the
safe listening time is.
Be sure to observe the following guidelines
when using your headset.
• Listen at reasonable volumes for
reasonable periods of time.
• Be careful not to adjust the volume
continuously upwards as your hearing
adapts.
• Do not turn up the volume so high that
you can’t hear what’s around you.
• You should use caution or temporarily
discontinue use in potentially
hazardous situations.
• Excessive sound pressure from
earphones and headphones can cause
hearing loss.
• Using headphones with both
ears covered while driving is not
recommended and may be illegal in
some areas while driving.
• For your safety, avoid distractions
from music or phone calls while in
traffic or other potentially dangerous
environments.
2
EN
••
dampened with a minimum amount of water or
diluted mild soap, to clean the product.
The integrated battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
Risk of explosion if battery is replaced by an
incorrect type. Replace only with the same or
equivalent type.
About operating and storage temperatures
and humidity
• Operate or store in a place where
temperature is between -15ºC (5ºF)
and 55ºC (131ºF) (up to 90% relative
humidity.
• Battery life may be shorter in high or
low temperature conditions.
2 Onkyo
Bluetooth
wireless
headset
Other devices
Box content
Overview of your Bluetooth
wireless headset
A mobile phone or electronic device (e.g.
notebook, PDA, Bluetooth adapters, MP3
players etc) which supports Bluetooth and
is compatible to the headset (see 'Technical
data' on page 6).
9
1
8
2
3
Onkyo Bluetooth wireless headset W800BT
4
5
6
Replaceable rubber ear caps x 2 pairs
7
a On/off, call control button
b LED indicator
c Microphone
d USB cable (for charging)
Charging case
e Headset charging socket
f Battery indicator
g Battery indicator button
h LED indicator
i On/off button
Quick start guide
EN
3
3 Charge and pair
your headset
Charging case
Plug the USB cable into the power source.
The charging case starts charging.
Charge the battery
Note
•• Before you use your headset/charging case for
••
••
the first time, charge the battery for 5 hours for
optimum battery capacity and lifetime.
Use only the original USB charging cable to avoid
any damage.
Finish your call before charging the headset, as
connecting the headset for charging will power the
headset off.
Tip
•• Normally, a full charge takes 2 hours.
•• When the charging case is charging, the battery
••
4
EN
indicator keeps flashing until charging is complete.
There are 5 indicator lights. The leftmost LED light
indicates the charging status. The other 4 LED
lights indicate the battery level. Each LED light
indicated 25% battery. When all 4 LED lights are
turned on and stable, the charging case is fully
charged.
Press the battery indicator button to show the
battery level status.
Headset
Place the headset on the charging case.
The headset starts charging.
•
•
When the headset is charging, a white
LED light will be displayed.
When the headset is fully charged, the
white light goes off.
Pair between both sides of
the headset
1
Make sure that the headset is fully
charged.
2
Press and hold the power on/off button
on both sides of the headset for 2
seconds.
The white LED light on the left side
of the headset flashes slowly after
pairing with the right side of the
headset.
The white LED light on the right side
of the headset flashes rapidly. The
headset is ready to pair with the
Bluetooth device.
Pair your headset with the
Bluetooth device
Tip
•• Normally, a full charge takes 70 minutes.
1
Turn on the Bluetooth function of your
mobile phone.
2
Pair the headset with the mobile phone.
For detailed information, refer to the
user manual of your mobile phone.
Tip
•• The headset stores the last 4 devices in the
memory. If you try to pair more than 4 devices, the
earliest paired device is replaced by the new one.
EN
5
The following example shows you how to
pair the headset with your mobile phone.
1
Activate the Bluetooth feature of your
mobile phone, select Onkyo W800BT.
2
Enter the headset password "0000" (4
zeros) if prompted. For those mobile
phones featuring Bluetooth 3.0 or
higher, no need to enter a password.
Onkyo W800BT
6
EN
4 Use your
headset
Connect the headset to a
Bluetooth device
1
Turn on your mobile phone/Bluetooth
device.
2
Press and hold the power on/off button
for 2 seconds on both sides of the
headset.
The white LED light on the left side
of the headset flashes slowly after
pairing with the right side of the
headset.
The white LED light on the right side
of the headset flashes rapidly. The
headset is ready to pair with the
Bluetooth device.
The headset is reconnected
to the last connected mobile
phone/Bluetooth device
automatically.
Tip
•• If you turn on the mobile phone/Bluetooth device
••
or activate the Bluetooth feature after turning on
the headset, you have to reconnect the headset and
mobile phone/Bluetooth device manually.
If your mobile phone/Bluetooth device cannot
reconnect automatically, try to reconnect
manually by clicking the headset's name again
under the Bluetooth setting menu on your mobile
phone/Bluetooth device.
Operate your headset
On/off
Task
Turn the
headset
on.
Button
On/off,
call control
Turn the
headset
off.
on/off,
call control
Operation
Press and hold for
2 seconds.
You hear a
power on
signal tone.
Press and hold for
4 seconds.
The white
LED is on for
2 seconds
and then the
headset is off.
You hear a
power off
signal tone.
Call control
Task
Pick
up/hang
up a call.
Reject an
incoming
call.
Button (right
headset)
On/off,
call control
Operation
On/off,
call control
Press and
hold for 2
seconds.
Press once.
Note
•• If the headset fails to connect to any Bluetooth
device within range in 5 minutes, it will switch off
automatically to save the battery life.
EN
7
LED indicator status
Headset
status
Off/Charging
is complete.
Unconnected
between
both sides of
the headset.
Ready for
pairing
between
both sides of
the headset.
Pairing
with the
Bluetooth
device.
Paired and
ready to use.
During
music
playback.
When
there is an
incoming
call.
In a call.
Right side of
the headset
Off
Left side of the
headset
Off
N/A
The blue LED
flashes slowly.
The blue
and white
LEDs flashes
rapidly.
The blue and
white LEDs
flashes rapidly.
The white LED N/A
light flashes
rapidly.
The white LED
light flashes
slowly
One short
beep.
The blue LED
flashes slowly.
The white LED
light flashes
slowly.
The blue LED
flashes slowly.
The blue and The white LED
white LEDs
flashes slowly.
flashes slowly
The blue LED
is on.
The white LED
flashes slowly.
Charging is
in progress.
The white LED The white LED
is on.
is on.
Low battery
level.
The white
The blue and
LED light
white LEDs
flashes twice flashes rapidly.
for every 10
seconds.
Low
battery
signal tone
for every
minute.
8
EN
Wear your headset
1
Push your headset inward and rotate it
forward to ensure the winglet is nested
inside the cavity above the ear canal.
2
Rotate your headset forward and
backward accordingly for the best
personal fit.
5 Technical data
Headset
• Play time: up to 3 hrs (up to 15 hrs with
charging case)
• Standby time: 40 hrs (up to 200 hrs
with charging case)
• Charging Time: 70 mins
• Rechargeable Li-ion battery: 55mAh
• Bluetooth 4.1, Bluetooth mono support
(Headset profile - HSP, Hands-Free
Profile - HFP), Bluetooth stereo
supported (Advanced Audio Distribution
Profile - A2DP)
• Operating range : Up to 10 meters (33
feet)
• Digital noise and echo reduction
• Auto power off
Charging case
• Charging time: 2hrs
• Rechargeable Li-ion battery : 900mAh
• Number of recharges supported: 5
Note
•• Specifications are subject to change without notice.
EN
9
6 Notice
Declaration of conformity
Hereby, Gibson Innovations declares that
this product is in compliance with the
essential requirements and other relevant
provisions of Directive 2014/53/EU. You
can find the Declaration of Conformity on
www.onkyo-headphones.com
Disposal of your old product
and battery
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
This symbol means that the product
contains a built-in rechargeable battery
covered by European Directive 2013/56/EU
which cannot be disposed of with normal
household waste. We strongly advise you
to take your product to an official collection
point to have a professional remove the
rechargeable battery.
Inform yourself about the local separate
collection system for electrical and
electronic products and rechargeable
batteries. Follow local rules and never
dispose of the product and rechargeable
10
EN
batteries with normal household waste.
Correct disposal of old products and
rechargeable batteries helps prevent
negative consequences for the environment
and human health.
Remove the integrated battery for
disposal
If there is no collection/recycling system for
electronic products in your country, you can
protect the environment by removing and
recycling the battery before disposing the
headset.
•
1
2
3
Make sure the headset is disconnected
from the charging case before
removing the battery.
•
Make sure the charging case is
disconnected from the USB charging
cable before removing the battery.
Compliance with EMF
This product complies with all applicable
standards and regulations regarding
exposure to electromagnetic fields.
Environmental information
All unnecessary packaging has been
omitted. We have tried to make the
packaging easy to separate into three
materials: cardboard (box), polystyrene
foam (buffer) and polyethylene (bags,
protective foam sheet.)
Your system consists of materials
which can be recycled and reused if
disassembled by a specialized company.
Please observe the local regulations
regarding the disposal of packaging
materials, exhausted batteries and old
equipment.
Trademarks
Bluetooth
The Bluetooth® word mark and logos
are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such
marks by Gibson Innovations Limited
is under license. Onkyo® is a registered
trade mark of Gibson Brands Inc. Other
trademarks and trade names are those of
their respective owners.
7 Frequently
asked
questions
My Bluetooth headset does not switch on.
The battery level is low. Charge the headset.
I cannot pair my Bluetooth headset with a
mobile phone.
The Bluetooth is disabled. Enable the
Bluetooth feature on your mobile phone and
turn on the mobile phone before you turn on
the headset.
Pairing does not work.
Make sure the headset is in pairing mode.
• Follow the steps described in this user
manual (see ‘Charge and pair your
headset’ on page 4).
• Make sure that the LED light flashes
rapidly on the right side of the headset.
The mobile phone cannot find the headset.
•• The headset may be connected to a
previously paired device. Turn off the
connected device or move it out of
range.
•• Pairing may have been reset or the
headset has been previously paired
with another device. Pair the headset
with the mobile phone again as
described in the user manual (see
‘Charge and pair your headset’ on page
4).
12
My Bluetooth headset is connected to a
Bluetooth stereo enabled mobile phone,
but music only plays on the mobile phone
speaker.
Refer to the user manual of your mobile
phone. Select to listen to music through the
headset.
The audio quality is poor and crackling noise
can be heard.
The Bluetooth device is out of range. Reduce
the distance between your headset and
Bluetooth device, or remove obstacles
between them.
The audio quality is poor when streaming
from the mobile phone is very slow, or audio
streaming does not work at all.
Make sure your mobile phone not only
supports (mono) HSP/HFP but also supports
A2DP (see ‘Technical data’ on page 9). Why is there a lag between the sound and
video when I use the ONKYO True Wireless
Headphones for watching videos or playing
games?
Constant audio lag behind video scenes would
be found when you are watching videos or
playing games with the ONKYO True Wireless
Headphones. The audio lag is due to the time
for audio synchronization between the left
and right sides of the headset, so the audio
may have delay compared to the video scenes.
Audio lag is not a problem for listening
to music with the Onkyo True Wireless
Headphones.
For further support, visit
www.onkyo-headphones.com
[ 4.0 Using
MUSIC CONT
Play/Pause
Volume up
Volume down
Skip forward
www.onkyo.com
Skip backwar
[ 5.0 LED In
A white light
An alternatin
A blue light fl
A blue light fl
Limited. All rights reserved.
factured by, and is sold under
nnovations Ltd., and Gibson
ntor in relation to this product.
nds B.V. Building
2016 © Gibson Innovations Limited. All rights reserved.
This product has been manufactured by, and is sold under the
responsibility of Gibson Innovations Ltd., and Gibson Innovations
Ltd. is the warrantor in relation to this product.
Onkyo® is a registered trade mark of Onkyo Corporation. Other
trademarks and trade names are those of their respective owners.
[ 6.0 Corde
You can also
using the au
[ 7.0 Multip
Pairing add
A total of 4 b
simultaneou
Switching b
The multipoi
one device a
When you re
the audio res
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising