- Surveillance
INSTALLATION
MANUAL
Cross Platform Control
Part # ELK-M1EZ8
TM
A member of the M1 Family
Specifications, Installation and Programming
Includes the SIA CP-01 Standards for False Alarm Reduction
L Rev. F 12/22/05
WWW.DIYALARMFORUM.COM
Current with Firmware 4.3.8
Introduction
LIMITATION
This control is designed to warn against unauthorized entry and other situations. However, it is not a guarantee of protection against the
occurrence of burglary, fire, or other emergency. Any alarm system is subject to compromise or failure to warn for various reasons. For
example:
- Unauthorized access can be gained through unprotected points or by disarming or bypassing protected points.
- Sensing devices are power driven and do not operate without electrical power. Battery-operated devices will not work without batteries, with
dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any
reason, however briefly.
- Telephone lines over which alarm signals are transmitted may be out of service or rendered inoperable by an intruder.
- Even if the system responds to the emergency as intended, occupants may have insufficient time to protect themselves from the emergency
situation. In the case of a monitored alarm system, authorities may not respond appropriately.
- Smoke detectors have limitations and cannot detect all types of fires. According to data published by the Federal Emergency Management
Agency, while smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or provide
early warning for a variety of reasons in as many as 35% of all fires, . Some of the reasons some detectors used in conjunction with this
System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense
fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke
detectors also may not sense a fire on another level of a residence or building. A second floor detector, for example, may not sense a first floor
or basement fire. Finally, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general,
detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas,
improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending an the nature of the
fire, and/or location of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all
occupants to escape in time to prevent injury or death..
- Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path
has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path.
- Wireless transmitters (used in some systems) are designed to provide long battery life under normal operating conditions. Longevity of
batteries may be as much as 4 to 7 years, depending on the environment, usage, and the specific wireless device being used. External
factors such as humidity, high or low temperatures, as well as large swings in temperature, may all reduce the actual battery life in a given
installation. This wireless system, however, can identify a true low battery situation, thus allowing time to arrange a change of battery to
maintain protection for that given point within the system.
- Installing an alarm system may make the owner eligible for a lower insurance rate, but an alarm system is not a substitute for insurance.
Homeowner, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and
property.
- A user may not be able to reach a panic or emergency button quickly enough.
- Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive
Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can only be detected
in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed
doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows
or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the
ambient temperature of the protected area approaches the temperature range of 90 to 105F (32 to 40C), the detection performance can
decrease.
- Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other side of
closed or partly open doors. If warning devices are located on a different level of the residence from the bedrooms, they are less likely to
waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled by noise from a
stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearingimpaired people.
- This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 20
years, the electronic components could fail at any time.
- The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm
system should be tested weekly to make sure all sensors and transmitters are working properly.
ALL RIGHTS RESERVED
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise without the prior written permission of the manufacturer. The material in this publication is for information
purposes and subject to change without notice. The manufacturer assumes no responsibility for any errors which may appear in this publication.
Printed in U.S.A.
Use of this control for fire detection and/or annunciation may not be permitted by certain states, counties, municipalities or local jurisdiction. It is
the responsibility of the installing alarm company to check with the local A.H.J. (Authority Having Jurisdiction) or State Fire Marshal’s office prior
to using this control for fire detection.
Page 2
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
Table of Contents
Specifications, Features, and Benefits ..................................................................................................... 4
Wiring & Hookup Diagram ........................................................................................................................... 5
Section 1 - Installation and Wiring ............................................................................................................. 7
1.1 Planning the Installation ...................................................................................................................... 7
1.2 Parts Diagram & Descriptions ........................................................................................................... 7
1.3 Mounting and Wiring Preparation ....................................................................................................... 7
1.4 Control Wiring .................................................................................................................................... 8
Data Bus E.O.L. Termination - VERY IMPORTANT! ............................................................................... 11
Section 2 - Operating the System ............................................................................................................ 13
2.1 Introduction ....................................................................................................................................... 13
2.2 Powering Up (One Keypad) ............................................................................................................. 13
2.3 User Codes and Authorities .............................................................................................................. 13
2.4 Installer Program Code and Authorities ............................................................................................ 13
2.5 Keypad Overview ............................................................................................................................. 14
Keypad Menus ........................................................................................................................................ 15
Multi-area (Partition) Operation ............................................................................................................... 18
Section 3 - Programming The Control ..................................................................................................... 19
3.1 Introduction ....................................................................................................................................... 19
3.2 Local Keypad Programming ............................................................................................................. 19
3.3 Local or Remote Computer Programming (ELK-RP) and Anti-Takeover ......................................... 19
3.4 Area Partitioning ................................................................................................................................ 19
3.5 Communicator Setup Checklist ....................................................................................................... 20
3.6 Entering Installer Level Programming ............................................................................................... 20
Menu 01 - Bus Module Enrollment .......................................................................................................... 22
Menu 02 - User Code Options ................................................................................................................ 23
Menu 03 - Area Definitions ...................................................................................................................... 24
Menu 04 - Keypad Definitions ................................................................................................................. 26
Menu 05 - Zone Definitions ..................................................................................................................... 28
Menu 06 - Alarm Duration Timers ........................................................................................................... 31
Menu 07 - Global System Definitions ..................................................................................................... 32
Menu 08 - Telephone Account Setup ...................................................................................................... 36
Menu 09 - Area Reporting Codes ........................................................................................................... 38
Menu 10 - Zone Reporting Codes ........................................................................................................... 40
Menu 11 - Keypad F-Key Reporting Codes ............................................................................................ 41
Menu 12 - Sys Report Code Options & Codes ...................................................................................... 42
Menu 13 - User Report Codes ................................................................................................................ 44
Menu 14 - Wireless Definitions ............................................................................................................... 45
Section 4 - PC Programming and Automation Capabilities .................................................................... 47
4.1 ELK-RP Software ............................................................................................................................ 47
4.2 Update/Verify Firmware in the Control and Peripherals ................................................................... 48
4.3 Automation Rules and Attributes ...................................................................................................... 49
Appendix A - Event Codes ........................................................................................................................ 56
Appendix B - Two Way “Listen-in/Talk” Interface (optional) ................................................................. 58
Appendix C - SIA CP-01 Compliance ........................................................................................................ 59
Appendix D - Regulatory Agency Statements ......................................................................................... 60
Appendix E - Additional Keypad Information ........................................................................................... 64
Index ............................................................................................................................. 67
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 3
Specifications, Features, and Benefits
General:
• Large zone capacity: 8 on-board zones expandable to 200
• Wireless capability: Up to 48 zones
• Two Way Listen-in interface
• Flash Memory - Allows field updates to firmware electronically
• Time/Date stamped 512 event history log
• Menu driven, text keypad programming
• 12 On-Board Outputs: 1 siren driver/voltage, 1 form “C” Relay,
and 10 low current (10 mA) voltage outputs
• Total Number of Outputs Supported: 204
• Supports 4 wire (any zone) and 2 wire (zone 8) smoke
detectors
• Includes Fire alarm verification routine
• Can be partitioned into 8 areas and account numbers
• User Codes: 99 (4 or 6 digit) with assignable authority levels
• Arm levels: Away, Stay, Stay Instant, Nite, Nite Instant, Vacation
• Hardware "watchdog" and nonvolatile EEPROM memory
• Supervised phone line and alarm output
• Connection for optional ELK-MSI RS-232 serial port 0 to
interface PCs and peripheral devices
• Total serial ports with expansion: 8
Communications
• True V.22 bis Modem for fast reliable upload/download
• Phone Number Capacity: 8
• Optional Ethernet int. for reporting, operation, programming
• Communicator formats: SIA, Contact ID, 4 + 2, and Pager
• Elk-RP PC programming software with conflict resolution to
easily highlight differences between control and PC
- Connect via Dial-up, Optional RS232 port, or Opt. Ethernet
- Automatic answering machine bypass
Keypad
• Backlit, Large Character LCD Display, 16 x 2 lines
• Built-in Temperature Sensor
• Optional Plug-in Prox Access reader (26 bit Weigand format)
• Menu navigation keys and 6 programmable function keys
• Plug-in connector, only 4 wires to the control
• 1 Zone input and 1 Output Programmable per Keypad
• Programmable display of time, date, & temperature
• Displays system diagnostics and settings.
• Maximum Keypads allowed: 16
Automation & Integration
• Create lifestyle enhancing comfort, convenience, and security
• Powerful “Whenever/And/Then” RULES Programming allows
almost any imaginable operation. No need to chain rules
Page 4
•
•
•
•
•
•
together. Any single “Whenever” event can have one or more
ANDs and THENs (conditions and commands).
Total number of Rules Supported: 528
Rules utilize easy to understand text based references
Control lighting using RS-232 serial or 2-way Power Line
Control (PLC) ports including On, Off, Dim, All On, All Off
commands
Transmit and receive custom serial ASCII strings
Read Temperature Sensors - Communicate with Thermostats
Total thermostats supported: 16
Sunset/Sunrise calculation and activation built-in
•
• Advanced Lighting Options (Pre-set Dim, Extended, Levels,
Scenes)
Power Supply
• Heavy duty - 2.5 Amp power supply w/ 1.5 Amp continuous
• Dynamic battery test
• PTC (fuseless) resettable overload protection
Part Numbers and Accessories:
ELK-M1EZ8CB Control “Board only”
ELK-M1EZ8
Control in 12 x 12” metal can (Base Unit)
ELK-M1EZ8KB Control KIT: Board, 12 x 12” can, Xfmr, M1KP
Keypad, 5Ah Battery, SP35 Speaker, RJSET,
ELK-M1EZ8K
Control KIT - NO METAL CAN (for structured
wiring systems) Includes Board,XFMR,M1KP
Keypad, 5Ah Battery, SP35 Spkr, RJSET
Utilizes most ELK-M1 Accessories
ELK-M1KP
ELK-M1XIN
ELK-M1XOVR
ELK-M1XOV
ELK-M1RB
ELK-M1DBH
ELK-M1XEP
ELK-M1XSP
ELK-M1PR
ELK-M1EZ8TWI
ELK-M1EZ8MSI
ELK-M1TWS
ELK-M1ZTS
ELK-RP
Keypad, LCD,16 character x 2 line
16 Zone (input) expander
16 Output expander, 8 Voltage/8 Relays
16 Output expander, Voltage only
Relay board, 8 form ”C” relays
Data bus wiring hub
Ethernet Port Exp/Interface (Qtr 2 of 05)
Lighting, Thermostat Interface & Serial exp.
Mini prox reader for keypad
Two Way Listen-in Int. w/3 mic inputs
Main Serial Interface, supplies RS232 Port 0
Speaker & Mic for Two Way Listen-in
Zone Temperature Sensor -50 to 140 F
PC software, free with 1st Control purchase
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
Wiring & Hookup Diagram
12V
Battery
Status LED:1 blink = Normal Operation.
2 fast blinks = Bootloader mode.
4 fast blinks = Initializing EEPROM memory.
5 fast blinks = Memory/Operation overflow.
Testing of this system should be performed
regularly. Control panel specifications are subject
to change without notice. Figures not to scale.
ELK PRODUCTS, INC.
HILDEBRAN, N.C., 28637, USA
+12V
KP
RED
GREEN
WHITE
BLACK
Data Bus-See Note in Manual
Keypad
JP3 Terminating Jumper (JP3)
See manual for important information
about Data Bus Termination.
A
2 WAY
-X101 WAY
B
NEG
Out 2 - Alarm (Siren or Voltage)
Connect a UL Listed siren or bell.
Default is Siren Min. 15 watt
(4-16 Ohm) speaker ELK-SP30
or equiv.
+ (Supervised)
J7
Programmable Outputs (J16)
OUT 7 thru 16 are +12V switched positive
voltage outputs rated at 10mA max.
Connect optional ELK-M1RB Relay Board
for 8 general purpose relays.
8
1
Two-Way
Listen-In (J7)
Connects to
(M1EZ8TWI)
1
Aux Data Bus (J3)
For wireless receiver. Presently
works with GE-Caddx NX408E,
NX416E, or NX448E
J16
+12V
NEG
OUT 16
OUT 15
OUT 14
OUT 13
OUT 12
OUT 11
OUT 10
OUT 9
OUT 8
OUT 7
J3
B
A
C
+
LINE SEIZE
JP1
2WIRE NORMAL
SMOKE ZONE 8
Line Seize LED is ON if Dialer
is in use (communicating)
2200 Ohm EOL Resistors are part # ELK-ER2200
+VAUX NEG +VSMK Z8
NEG
Z6
Z7
NEG
Z5
Z4
NEG
Z3
Z2
NEG
Z1
PHONE LINE HOUSE LINE
TIP RING T1
R1
Green
+
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.
Zone
8
Zone
7
Zone
6
Zone
5
Zone
4
Zone
3
Zone
2
Zone
1
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
2200
Ohm
EOL
2200
Ohm
EOL
2200
Ohm
EOL
2200
Ohm
EOL
2200
Ohm
EOL
2200
Ohm
EOL
2200
Ohm
EOL
2200
Ohm
EOL
RJ31X Jack
(ELK-RJSET)
T1 8
To Zone Input
2200
Ohm
EOL
To Zone NEG
-
+
+
U.L. Listed EOL Supervision Relay
(ESL #204 or Equivalent).
(shown energized, contacts closed)
+12VDC Switched
Smoke Power
1.1 Amp PTC protected
T 5
-
+
Z8 NEG
Demark
Block
splices
T1 R1 Ring Tip
House
Phones
2-Wire
Smoke
Detector
680 Ohm EOL
To J5
Connector
Zone 8 can be configured as a 2-wire smoke zone. Set JP1 to "2
WIRE SMOKE" and use 680 Ohm EOL resistor, part # ELK-ER680
Use Only Compatible Detectors:
System Sensor: 2WTA-B, 2WTR-B, 2100, 2100T
GE: 429AT, 521BXT, 521B.
Hochiki America: SLK-835.
Detection Systems: DS250, DS250TH, DS282, DS282TH,
DS282THS, DS282THC.
Maximum Number = 20 Do not mix models.
4 R
Yellow
Red
Black
Green
2-Wire Smoke Circuit
TELCO
Line
Compiles with FCC Part 68
Reg. Number: US:5K6AL03BELK-M1
Ringer Equivalence REN: 0.3B
Use USOC RJ-31X connector.
Complies with the limits for class B computer
devices in accordance with the specifications
of subpart J of part 15 of FCC rules.
Note: Secondary phone line surge
su ppr essi on d evi ces ( ELK -95 0) ar e
recommended for areas prone to transient
or lightning strikes.
Connector J5 accepts either a 4 conductor modular cable for a PSC05 PLC
Lighting Interface OR an 8 conductor modular cable for a EZ8MSI Main Serial Port
Interface w/PSC05 pass through connector. (This connection not evaluated by UL)
4 Con
Modu ductor
lar Ca
ble
OR
8 Conductor
Modular Cable
End view
PSC05
or
equiv.
ELK-M1EZ8MSI
Main Serial Port Interface
(Sold separately)
PSC05 or
Equivalent
1 R1
4-Wire Smoke Detector
N.O. Alarm
Contacts
1
Red Brown Grey
-
NOTE: Maximum continuous current drain from
+VAUX, +12VKP, +VSMK, and J16 combined must
not exceed 1 Amp (2.5 Amps in alarm)
J1
From
EZ8
1
1
Red
Black
White
Green
Brown
Blue
Orange
Yellow
Violet
Grey
Pink
Tan
OUTPUT 3
COM N/C
Out 3 - Relay Programmable
General Purpose Dry Contacts
rated: 5Amps @ 12 - 28VDC
Select PLC Mode (JP2)
Selects single or bi-directional
PLC Transmissions
JP2
For PLC Lighting
Interface
or M1EZ8MSI Main
Serial Port Interface
See Manual
Do Not Connect
to a Phone Line!
N/O
For Voltage (open collector)
program option G26 to a Yes. Max.
Current Draw: 1 Amp If output is not
used, install a 2200 Ohm resistor to
avoid Output 2 trouble.
J5
OUTPUT 2
+ ALARM -
Siren or Voltage
Auxiliary +12VDC
Power Output
Protected by 1.25A PTC.
ELK-M1EZ8
Power LED is ON when AC Voltage is present.
16V XFMR
AC AC
UL Listed
Transformer,
16.5VAC, 45VA.
Class II,
(ELK-TRG1640)
Do not connect to switched outlet.
-
RED BLK
BATTERY
Note: Test battery regularly with
ELK-BLT Battery Life Tester.
Replace every 3-5 years
POWER
STATUS
Sealed Lead Acid
Battery (ELK-1250)
12Volt - 5Ah min.
See UL requirements
for sizes and standby
times.
J2
Powerline
Interface
1
1
J3
RS-232
4 Conductor
Modular Cable
Computer, OEM
component, etc.
End view
1
Yellow
Green
Red
Black
Yellow
Green
Red
Black
1
1
4 conductor modular (standard) phone
cord for PLC Lighting (not supplied).
Pin 2 < to > 2
Pin 3 < to > 3
1
Pin 5 < to > 5
RS232 Serial Port Cable (9 pin male
to 9 pin female) Max. length = 50 ft.
083005
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
1
Wht/Org
Org/Wht
Wht/Grn
Blue/Wht
Wht/Blue
Grn/Wht
Wht/Brn
Brn/Wht
8 Conductor Cat5 cable from EZ8MSI Main Serial Port Interface.
PC
RS232
Serial
Cable
Brn/Wht
Wht/Brn
Grn/Wht
Wht/Blue
Blue/Wht
Wht/Grn
Org/Wht
Wht/Org
[Effective w/Firmware 4.3.6]
Page 5
Intentionally Left Blank
Page 6
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
Section 1 - Installation and Wiring
1.1 Planning the Installation
The first step in any multi-zone security system installation is planning the job.
1. Read this entire manual to familiarize yourself with all system features and procedures before actually beginning the
installation. Read all the information regarding Underwriters Laboratories (UL) and NFPA requirements.
2. Perform a physical survey of the installation site. Use the diagrams below as a guide in planning the installation.
3. Discuss the installation requirements and applications with the customer.
4. Compare the installation requirements and applications with the factory default settings to determine what customized
programming is needed to meet the specific installation requirements.
5. Bench test the system prior to installation.
TYPICAL BURGLARY INSTALLATION LAYOUT
Bedroom 2
TYPICAL FIRE INSTALLATION LAYOUT
Bedroom 1
Bedroom 2
S
Kitchen / Dining
M
C
C
C
S
K
C
A
S
Bedroom 3
Living Room
C
Kitchen / Dining
M
A
Bedroom 3
Bedroom 1
S
Living Room
C
K
All perimeter openings below 18" should be provided with protection.
A Smoke Detector shall be located in each sleeping area and between
the sleeping areas and the main living area.
Early warning fire detection is best achieved by the installation of fire
detection equipment in the location shown above.
M
A
S
C
K
Legend
- Main Control
- Audible Alarm
- Smoke Detector
- Contact
- Keypad
First Floor
In homes basements or multiple levels at least one smoke detector
shall be on each level.
Basement
1.2 Parts Diagram & Descriptions
See Wiring & Hookup Diagram on pages 5.
1.3 Mounting and Wiring Preparation
Control Mounting
Remove all packing material and familiarize yourself with the parts. Mount the control in a secure, dry location where the
ambient temperature inside the control box can remain at 32‘ to 120° Fahrenheit (0’ to +49' Celsius). Choose a location that
allows easy wiring to an unswitched power outlet and to a grounding conductor for the control. A central location makes
running system wiring easier. Remove control box knockouts that best suit your wiring needs. Mount the control using the
upper center slotted hole to level. Install and connect all necessary wiring for the power transformer, detection loops, keypads
and siren outputs.
Keypad Mounting and Wiring
Ideal keypad height is 50-58 inches above the floor. Select a location with an ambient temperature range between 32° and
120° F (0° to +49° C). Avoid direct sunlight if possible. Fasten mounting plate to electrical box (or directly to wall) using flat
head screws to prevent shorts to the back of the circuit board. Keypads have a removable wiring plug for connecting to the 4wire data bus. CAT5 or CAT6 eight (8) conductor cable is recommended for all Data Bus cables. The extra wires provide
data return paths. Splice the Black, Red, White, and Green wires from the removable wiring plug to the Data Bus cable. Plug
the connector into the back of the keypad. Tuck wires neatly into back plate and install Keypad on mounting plate. Each
keypad has connections for an optional programmable output and a programmable zone input.
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 7
Hookup Diagram for Keypad
Splice 6 Pin Keypad Wiring Assembly to the Data Bus cable using ELK-900-2 "B" Connectors.
BLACK
WHITE
GREEN
RED
BLUE
BROWN
Data Bus Cable
CAT5 or CAT6 Recommended
To Red (Pos) Wire
To Brown Wire
+
-
Keypad 1
1
6
To BROWN Wire
Load (50mA max)
i.e. Relay, LED
See Note about
Data Bus
Termination
ELK-M1KP
Keypad
Wiring
Assembly
To BLACK (Neg) Wire
The optional Zone Input # or Output # is
determined by the Keypad Address.
+
-
Load (50mA max)
I.E. LED, Relay
Optional programmable Output from Keypad
NOTE: The first batch of M1KP Keypads provided a switched
negative (pull to ground) output. Connect per diagram above.
These units have the letter "E" at the end of the ID number on the
lower back side of the board. EG: PC096E Boards with a letter
"F" or later provide the output as a switched positive.
To BLUE Wire
2200
Ohm
EOL
N.C. N.O.
To BLACK (Neg) Wire
Optional programmable Zone Input from Keypad
KP
Zone Output
Address #
#
1
193 193
2
194 194
3
195 195
4
196 196
5
197 197
6
198 198
7
199 199
8
200 200
KP
Zone Output
Address #
#
9
201 201
10 202 202
11 203 203
12 204 204
13 205 205
14 206 206
15 207 207
16 208 208
NOTE: Refer to the section ‘Data Bus E.O.L. Termination’ for information on multiple homerun cables. NEVER SPLICE OR
CONNECT WIRE WITH CONTROL POWER ON. Minimum cabling should be four conductor 22 or 24 gauge. Maximum resistance per wire is
25 Ohms. Device placement beyond 1000' is not recommended.
1.4 Control Wiring
Zone Inputs (1 thru 8 on main board, 17 thru 208 via expanders)
Zones Z1 thru Z8 are on the main board, others are in groups of 16, starting with Z17. Each 2 zones share a common
negative terminal. A zone may be programming for EOL resistor supervision (Default), or normally closed/normally open
without a resistor. In addition, Burglar and Keyswitch zones may be programmed for EOL with Security Alert on Short, or EOL
with Security Alert on Open/Short, also referred to as a Four (4) State Zone (firmware 4.3.5 or later). If EOL resistors are used,
they should be placed at the furthest most remote end of the detection device wiring. EOL zones permit a combination of
N.C. (normally closed) or N.O. (normally open) devices. Using voltage meter probes across the zone and com terminals, a
non-violated EOL zone will measures approx. 7.0 VDC. An open circuit will be approx. 13.8 VDC. A shorted circuit will be
0 VDC. The Keypad also provides the ability “Menu 8 “System Diagnostics” to view zone voltage.
Traditional Three (3) State Zone Wiring (1 series resistor)
2200
Ohm
EOL
Zone Input
N.O.
Contact
N.C.
Alarm
Contact
Wire in Series with zone
input or use another zone.
N.C. Tamper
Contacts
Neg.
Alarm Contact
Condition When:
Diagostic Table
Zone
Resistance
Approx. Range
of Zone Voltage
A to D
Value
Armed
Disarmed
Short ~
2.2k Ohms
Open ~
0 - 3.9 Volts
4.0 - 8.8 Volts
8.9 - 13.8 Volts
0 - 72
73 - 170
171 - 255
Alarm
Alarm
Not Ready
Ready
Not Ready
N.C. Alarm
Contacts
2200 Ohm
EOL Resistor
Neg.
Pos.
Neg.
Powered Motion, PIR, Glassbreak, etc.
Optional Four (4) State Zone Wiring (2 series resistors w/ N.C. contacts)
Tamper Contact
2200
Ohm
EOL
N.C.
N.C.
Alarm
Contact
2200 Ohm
EOL
Neg.
This feature
requires Firmware
2.3.5 or later.
Program Zone for EOL Wiring
Type 4 - Supervisory on Open
Zone
Input
N.C. Tamper
Contacts
Fig 1: N.C. Alarm Contact
(Unpowered) with N.C. Tamper
Diagnostic Table
Zone
Approx. Zone
Resistance Voltage Reading
Short ~
0 - 3.9 Volts
2.2k Ohms
4.0 - 7.3 Volts
4.4k Ohms
7.4 - 11 Volts
Open ~
11.1 - 13.8 Volts
Page 8
Zone Input
N.O.
Contact
2200 Ohm
EOL Resistor
Condition When:
A to D
Value
0 - 72
73 - 159
160 - 220
221 - 255
Zone
Input
Armed
Disarmed
Alarm
Alarm
Alarm
Sec. Alert/Tamper
Ready
Not Ready
Sec. Alert/Tamper
N.C. Alarm
Contacts
2200 Ohm
EOL Resistor
Neg.
Pos.
Neg.
Fig 2: Powered PIR, Glassbreak, etc. with Tamper
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
Two-Wire Smoke Zones (Zone 8)
To enable the use of two-wire smoke detectors on Zone 8, move Jumper JP1 to the 2 wire smoke position. Go to the installer
programming mode, Menu 05 - Zone Definitions, and program Zone 8 as a Fire zone (Def=10). Program the Wire Type as a 6.
NOTE Use only compatible two-wire detectors as listed on the front label of the control. Do not mix brands. The
maximum number of detectors is also listed on the front label. When jumper JP1 is set for two-wire operation, a 680
Ohm EOL resistor (furnished in the hardware pack) must be used instead of the 2,200 Ohm. Maximum wire resistance
must not exceed 60 Ohms.
Switched Power Connection (+VSMK)
Four-wire smoke detector and other devices that require a temporary power disruption in order to reset or unlatch from the
alarm state (i.e. smoke detectors, etc.) should be connected to the +VSMK 12 Volt DC switched power terminal. When a
smoke reset is performed, the operating voltage to these devices is momentarily interrupted.
Auxiliary Power Connections (+VAUX)
Motion detectors, glass breaks, etc. and other devices requiring unswitched 24-hour power should be connected to one of the
auxiliary terminals, +VAUX. All negative terminals on the terminal strip are at the same reference and may be used whenever
a common (circuit ground) negative is required. Use caution when wiring the control to distribute the load devices among the
supply and the negative terminals evenly. NOTE: Circuit ground refers to any negative terminal connection on this control.
This does not refer to earth ground or to the common terminal of the relay output.. These are not at the same voltage
potential and should not be wired so that they are electrically connected to a negative.
PTC (Positive Temperature Coefficient) Circuit Breakers
The +VAUX Auxiliary power and J16 power output terminals are protected against shorts and overloads by a 1.25A PTC. A PTC
is a solid state, auto-restoring type of circuit breaker. The +VSMK Switched (Smoke) power output is protected by a 1.1A PTC.
The +12VKP Keypad power output is protected by a 1.25A PTC. The alarm output is protected by a 1.25A PTC. NOTE:
Sometimes it may be necessary to remove power (unplug the outputs) for approx. 20 seconds after a short, to allow the
PTC to reset. Even if the short is no longer present, the remaining residual current draw may be so high that the PTC
cannot determine that the short is gone. If the PTC re-trips, check the field wiring and repair.
Transformer Primary Power Input (AC)
The control is powered by a 16.5 VAC, 40 min. VA, UL Listed Class II (power limited) transformer (ELK-TRG1640). The
specified sized and rated transformer must be used to operate this control. The transformer must be connected to a 120 VAC,
24-hour outlet not controlled by a switch other than an approved overcurrent protection device.
POWER
Power LED is ON when AC Voltage is present.
RED BLK
Status LED:1 blink = Normal Operation.
2 fast blinks = Bootloader mode.
4 fast blinks = Initializing EEPROM memory.
5 fast blinks = Memory/Operation overflow.
16V XFMR
AC
AC
UL Listed Transformer,
Class II, 16.5VAC, 45VA.
i.e ELK-TRG1640
Do not connect to a
switched outlet.
BATTERY
Test battery regularly with
ELK-BLT Battery Life Tester.
Replace every 3-5 years
12V Battery
STATUS
Sealed Lead Acid Battery
12Volt - 5Ah min. (ELK-1250)
NOTE: See UL requirements for
standby times and battery sizes.
The control is capable of
charging up to an 18Ah battery.
Connect the transformer to the AC Terminals using 16 to 18 gauge minimun wire. Do not exceed 50 feet between the
transformer and the control or run the AC power in a multiconductor with other system circuits. Leave the transformer
unplugged as well as the standby battery until all other connections have been made.
Standby Battery Connection
Connect the BLACK wire to the Neg (-) terminal on the battery, the connect the RED wire to the Pos (+) terminal on the battery.
The control is designed to operate with and recharge a 12 volt, sealed lead acid battery from 5Ah up to 18 Ah for backup of the
primary power supply. The control maintains a float charge for the battery of 13.8 VDC at 100 mA. This is in addition to the
continuous output of 1.5 Amps that the power supply maintains (see maximum current drains for UL Listed Systems).
CAUTION: Do not reverse the battery leads! The control has special circuitry which helps protect it from battery reversal
damage for short durations. However, prolonged reversal of the battery leads may cause permanent damage. A reverse
battery warning LED is located to the left of the power On/Off switch. If this light is ON, turn the power off immediately
and correct the battery lead connections.
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 9
AC Failure, Low Battery, and Automatic Low Voltage Shutdown
During an AC power failure the battery automatically takes over and AC Fail trouble annunciates at the keypad. The
communicator can be programmed to report AC Fail to the Central Station after a time delay (see Menu 12, System Option 01).
If the battery voltage falls below 11.2 VDC a Low Battery Trouble condition will occur. The communicator can be programmed
to report Low Battery to the Central Station. The battery will continue to run the control until its voltage reaches 10.5 VDC, at
which time the control will disconnect and shut down to prevent a false alarm and damage to the battery. The AC Fail trouble
display will clear if the AC restores. However, the Low Battery Trouble requires a manual or automatic battery load test before
it will clear. An automatic battery load test is performed every 24 hours. See Section 2.2 for powering up the control.
Telephone Line Connection (R1,T1,T,R)
The telephone interface is connected by the use of an approved RJ-31X interconnect jack. This device allows the subscriber
to disconnect the control/communicator from the public switched telephone network in the event of a malfunction. The control
is equipped with line seizure so that the premises telephone service is interrupted during communication to the central
station. Connection to the approved jack is done with a RJSET cord which connects the control terminals to the RJ31X jack.
HELPFUL HINT: The telephone cord can be supervised back to the RJ31X block or Telco demarcation block by installation of
a EOL resistor across the Orange and Blue wires (terminals 2 and 7 on the RJ31X jack). Back inside the control, connect the
Orange and Blue leads from the RJ cord to any 24hr Burglar zone input.
Outputs
There are 12 outputs on the main board. In programming these are numbered Out2, Out3, and Out 7 thru 16. The total
outputs may be expanded utilizing output expander boards connected to the RS-485 4-wire Keypad data bus. The Alarm
Output (Out 2) trips when any alarm is activated. All others must be enabled through the RP Rules Programming and can be
triggered by multiple conditions “events”. Do not exceed the current limits on voltage only outputs.
Output 2 is a traditional Alarm output. It is factory set to produce alarm siren sounds into standard 8 Ohm speakers (never go
below a total connected load of 4 Ohms). It can be alternately programmed to produce voltage only (12VDC) for driving selfcontained sirens or siren driver boards
Output 3 is a Single Pole Double Throw Relay with form “C” contacts (Com, N/O, and N/C).
Outputs 7, 8, 9, 10, 11, 12, 13, 14, 15, and 16 are low current, positive (+) voltage only, for driving LEDs, relays, etc. Outputs 4,
5, and 6 ARE NOT available from the main board. They can only be accessed with a data bus Output expander set to
address 1. This expander will replicate all the main board outputs, including outputs 4, 5, and 6.
ELK-924
+T -T NEG POS
Programmable Outputs (J16) OUT 7 - 16 are +12V switched
positive general purpose outputs rated at 50mA.
N/C COM N/O N/C COM N/O
+12V Red
Black
White
Green
Brown
Blue
Orange
Yellow
Violet
Grey
Pink
Tan
24V OPEN
+VAUX
NEG
OUT 16
OUT 15
OUT 14
OUT 13
OUT 12
OUT 11
OUT 10
OUT 9
OUT 8
OUT 7
D3
+12V
NEG
16
15
14
13
12
11
10
9
8
7
OUTPUTS
J16
Door
Strike
+
-
24V AC
Transformer
Using Output 7 (low current) with a sensitive relay to switch 24V AC to a Door Strike
Earth Grounding
Tests and studies have determined that the best results against lightning and transients are obtained by isolating the control
from ground. Do NOT connect any of the terminals, especially the Neg. terminals to earth ground. However, ancilliary devices
such as the ELK-950 Surge Protector on the incoming Telephone circuit are still recommended.
Keypad & Expanders on the RS-485 Data Bus (+12VKP, Data A, Data B, Neg)
Keypads and data bus expander devices connect to the four terminals marked +VKP, Data A, Data B, and Neg. The keypad
plug-in wire harness color code is: Red +VKP, Green Data A, White Data B, and Black (-) Neg. The +12VKP power terminal is
protected by an auto reset PTC device. In the event of a short circuit or malfunction, power will be removed from all devices
until the problem is resolved.
Page 10
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
Data Bus E.O.L. Termination - VERY IMPORTANT!
The control features a true RS-485 “differential” data bus operating at 38,400 bits per second. This is relatively high speed by
industry standards and ensures fast, accurate communications. With this speed, EOL data bus terminating resistors are
required to eliminate the possibility of reflection errors caused by varying cable lengths. Every data bus device; keypad, zone
expander, etc. and the control board has a built-in bus terminating resistor (120 Ohm) which is installed (activated) via a 2 pin
header/jumper (2 Gold Pins). The hardware pack includes two black shorting caps. When one of the shorting caps is placed
on the two gold pins, it installs (activates) the 120 Ohm terminating resistor across Data Lines A & B. Terminating resistors
are marked JP2 on the keypads and JP1 on the expanders. From the factory, no terminating resistors are installed (activated).
WARNING! The RS-485 Data Bus must NEVER have more than 2 terminating resistors header/jumpers installed.
Ideally, there should be no more than 2 home run cables (4 wire) with daisy chained devices along each. The last device on each cable
MUST have a terminating resistor installed (activated) via the gold 2 pin header/jumpers marked JP2 on keypads, JP1 on expanders. Place a
black shorting cap (see hardware pack) onto the 2 gold pins to install a 120 Ohm resistor across data lines A & B. If there is only 1 data bus
cable place a shorting cap on JP3 of Main Board. See alternate hookups below.
+VKP
DATA A
DATA B
NEG
EGND
ELK-M1XIN
ELK-M1KP
RS-485 Data Bus (Max. length is 4000 ft.
Max. bus devices vary by control.)
RS-485 DATA BUS
Jumper
Terminate
these two
devices.
ELK-M1KP
Keypad 2
Keypad 1
RED
GREEN
DO NOT Jumper
Terminate these devices.
ELK-M1XOV
WHITE
ELK-M1KP
Keypad 3
BLACK
Daisy Chain Connection of Data Bus Devices Using Two (2) Home Run Cables
For those that prefer to home run wires, use 6 or 8 conductor (CAT5 is ideal) cable. At each device, make a three way splice of the data A, the
device A wire (terminal), and a return data A1 wire (using one of the extra wires). At the control, make a two way splice of the data A1 return
wire (series connection) to the outgoing data A wire of the next cable. Repeat for the data B wire. Remember to install a terminating jumper on
the last wired device and the control JP3 ONLY! Electrically the data wires are now in series. Connect the POS (+) and Neg (-) power wires of
each device directly to the M1’s +VKP and Neg terminals. DO NOT SERIES THE POWER WIRES as this will cause unnecessary voltage loss.
NOTE: The power wires are parallel
connected to the +VKP & Neg terminals.
RED
+VKP
DATA A
DATA B
NEG
GREEN
WHITE
DATA
A1
B1
DATA
A1 A
DATA
A1 A
BLACK
For future
devices
+
RS-485 DATA BUS
RED +12
BLACK (-)
GREEN
WHITE
BLUE
BROWN
A
A1
SPARE
PAIR
Install Teminating Jumper
Cap on this last device
AND on the control JP3.
B
Keypad
Conductor
Cable
Keypad
B
1
Keypad
B1
B1 B
6 co
ndu
ctor
cab
les
6
-
Connect each device to the 6
conductor cable as shown.
B
See Keypad Diagram for connection
of Optional Output and Zone Input
Diagram for Daisy Chain Connection of Data Bus Devices Using 3 or More Home Run Cables.
The ELK-M1DBH † Data Bus Hub accepts CAT5 or CAT6 cable with RJ45 plugs on the ends and does all the work of series connecting the
DATA lines A & B. Terminate at the hub using the included RJ45 Terminating Plug in the first unused jack.
J3
J5
J7
J9
RS-485 DATA BUS
Front
view
CAT5 Cables
Keypad
Keypad
Pin1
8 - Brn/Wht
7 - Wht/Brn
6 - Org/Wht
5 - Wht/Blue
4 - Blue/Wht
3 - Wht/Org
2 - Grn/Wht
1 - Wht/Grn Pin1
rn
/B
ht
- W ht
/W
Org
+
J8
RJ45 Plug
CAT5
or
CAT6
Cable
A
Spare
Spare
RED +12V
BLACK (-)
GREEN (A)
G
rn
/W
ht
J1
J6
A1
J4
J2
Br
n/
W
ht
RJ45 Terminating Plug Insert in first unused jack and terminate the
control at JP3. DO NOT TERMINATE AT ANY OF THE DEVICES!
ELK-M1DBH Data Bus Hub †
B1
B
W
ht
/O
Wh
t/G
COLOR CODE for CAT5 or CAT6 Data Bus Cable
to RJ45 Plugs for ELK-M1DBH Data Bus Hub.
Mount M1DBH inside control. Connect it to the M1
Data Bus terminals using a 4 conductor cable.
rg
Keypad
WHITE (B)
BLUE
BROWN
rn
To BROWN Wire
To BLACK (Neg) Wire
+
-
Load (50mA max)
I.E. LED, Relay
Optional programmable Output from Keypad
To BLUE Wire
Daisy Chain Connection using the ELK-M1DBH and CAT5 Cables.
† Not evaluated by UL
N.C
.
N.O
.
2200
Ohm
EOL
Optional programmable Zone Input from Keypad
†† Not for use in UL Listed Installations
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
To BLACK (Neg) Wire
[Effective w/Firmware 4.3.6]
Page 11
The ELK-M1DBHR † "Active" Data Bus Hub Retrofit splits the Controls' main RS-485 Data Bus into 4 managed RS-485 branches. Each branch
can have 2 parallel home run cables for a total of 8 home runs. The last (end of line) device on each home run should be jumper terminated to
insure proper operation and supervision.
ELK-M1DBHR †
DATA BUS HUB FOR RETROFIT
RED
GREEN
WHITE
BLACK
Keypad
+
A
B
-
+
A
B
-
+
A
HILDEBRAN, N.C., 28637, USA
Mount M1DBHR inside control.
Connect it to the Data Bus terminals
using a 4 conductor cable.
The Maximum length of the
RS-485 Data Bus or any single
Branch is 4000 ft.
Max. devices varies by product.
+VKP protected with 1.25A PTC
ELK PRODUCTS, INC.
B
-
WHITE
-
DATA BUS
BRANCH 4
BLACK
B
WHITE
A
DATA BUS
BRANCH 3
BLACK
+
RED
Single Keypad /Bus Device:
If only one (1) Keypad or Bus Device
is connected to a branch (# 1 in this
example), place terminating jumper
on the Keypad/Bus Device AND on
JP2 of the M1DBHR.
JP5
JP4
DATA BUS
BRANCH 2
GREEN
DATA BUS
BRANCH 1
Jumper Terminate
this device AND JP2
on the M1DBHR.
JP3
RED
-
JP2
GREEN
B
This diagram illustrates the M1DBHR Hub as a single
branch on a Control. Terminate JP3 on Control and JP1
on the M1DBHR. If a second hub is wired to the Control
terminate JP1 on the hubs but DO NOT terminate JP3 on
Control. NEVER place more than two (2) terminating
jumpers on any branch of the RS-485 Data Bus!
WHITE
A
JP1
BLACK
WHITE
BLACK
INPUT
FROM CONTROL
GREEN
Terminating Jumpers (JP1 - JP5)
JP1 = Terminates Input from Control
JP2 = Terminates Branch 1
JP3 = Terminates Branch 2
JP4 = Terminates Branch 3
JP5 = Terminates Branch 4
See details about Data Bus Termination.
RED
RED
+
+VKP
DATA A
DATA B
NEG
GREEN
RS-485 DATA BUS
Keypad
Keypad
Jumper
Two Keypad /Bus Devices:
If two (2) Keypad/Bus Devices are connected to Terminate
a branch (#2 in this example), place terminating these two
devices.
jumper on both Keypads/Device and REMOVE
jumper JP3 on the M1DBHR.
Multiple Keypads/Bus Devices
(Series Connected):
If more than two (2) Keypad/Bus
Devices are connected to a
branch (#3 in this example), they
Jumper
MUST be series connected on no
Terminate
more than 2 homerun wires.
these two
Place terminating jumpers on
devices.
LAST device connected to each
homerun. REMOVE jumper JP4
on the M1DBHR.
DO NOT Jumper JP3.
DO NOT
Jumper JP5
Keypad
ELK-M1XIN
ELK-M1XIN
Keypad
One Keypad and one
Zone Expander:
When two (2) Bus
Jumper
Devices are connected
Terminate
these two to a branch (#4 in this
devices. example), place
terminating jumper on
both Bus Devices and
REMOVE jumper JP3
on the M1DBHR.
Keypad
ELK-M1KP
Keypad
DO NOT Jumper JP4.
DO NOT Jumper Terminate
these devices.
ELK-M1XOV
Diagram for Home run wiring using M1DBHR Active Data Bus Hub
Setting the Data Bus Address and Enrolling Device(s) into the System
Keypads and expander devices communicate over the RS-485 4-wire data bus. Each device must have a unique address
setting (from 1 to 16) within it's device type. Keypads are TYPE 1, input (zone) expanders TYPE 2, output expanders TYPE 3, etc.
The purpose of device types is so that the address numbers can be re-used in each different device type. It’s OK to have a
Keypad, Zone Expander, and Output Expander all set to address 2 and on the same data bus since each device is a different
device type. It is NOT OK to have duplications of addresses within the same device type. I.E. Multiple keypads on the same
control cannot be set to 'like' addresses.
ADDRESS: From the factory all keypads are set to address 1. Valid addresses are 1 to 16. The first keypad on the system
(Keypad 1) is automatically enrolled upon power up. Each additional keypad must be assigned a unique address and then
manually enrolled from “Menu 1 - Bus Module Enrollment”. (See Menu 01, for complete instructions on Bus Module Enrollment)
1. Press and hold the " * " key, followed by the F5 key . HOLD BOTH keys pressed for 5-10 seconds or until the LCD displays:
Exit when done. F1 Set Addr. (This is Keypad setup mode)
NOTE: An alternate method is to remove power from the keypad and then power up while holding any key pressed.
2. Press the F1 key to display the current address setting.
3. Set the desired address (from 1 to 16) by using the Up or Down arrow keys.
4. Press the Exit key twice when done.
ENROLLING:
1. Press the ELK key, then 9 (or scroll up) to display 9 - Installation Programming. Press the RIGHT
arrow key to select this menu. The Installer Program Code must be entered to access this menu.
2. Enter the Installer Program Code. (The default code is 172839)
3. The first Installer Programming menu displayed will be "Bus Module Enrollment"
4. Press the RIGHT arrow key to select this menu. "Enrolling Bus Modules" will display
5. After a few seconds the display will show the total Bus Modules that are enrolled. To view the
enrolled devices and/or remove a device press the RIGHT arrow key next to the word Edit.
6. Press the * or Exit keys to exit Installer Programming.
† Not evaluated by UL
Page 12
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
Auth. Required
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
Enter Valid Pin
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
01-Bus Module
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
Enrollment
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
XX Bus Modules
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
Enrolled, Edit r
12345678901234567890123456
12345678901234567890123456
†† Not for use in UL Listed Installations
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
Section 2 - Operating the System
2.1 Introduction
For best operation during bench testing, all zones should be terminated with end of line resistors and the correct transformer
and battery should be connected to the unit. The control comes with factory default programming, allowing it to be bench
tested prior to installation. The factory default code for user 1 is 3456. This code is authorized to operate all user related
features of the system. The control is designed to accommodate the grouping of specific zones into partitions called areas
and by default, all zones are assigned to area #1. This is the most common mode in which the system operates. This section
of the manual gives an overview of powering up and basic keypad functioning.
2.2 Powering Up (One Keypad)
After all other connections have been made and checked thoroughly, the controls AC transformer and battery may be
connected. Upon power up the control will perform self-diagnostics and auto-enroll the first keypad (Keypad Address #1). Any
additional keypads or expanders must be manually enrolled using Installer Level Programming. See “Menu 01 - Bus Module
Enrollment”.
NOTE: It is very important to make certain that every keypad, input expander, output expander, or any other data bus
device be assigned a unique data bus address within its type. See “MENU 01 - Bus Module Enrollment” for instructions
on setting keypad and expander addresses.
2.3 User Codes and Authorities
The control has 99 user passcodes plus one installer passcode. Each user code may be assigned specific authorities as to
what it is allowed to do. The authorities are assigned from the Installer level programming, however the code numbers and
user name is assigned from the keypad user menu 6 - Change User Codes. Only a Master authority level code or the
Installer code is allowed to access keypad user menu 6. The User’s Guide contains a description of panel
operations accessible to the user codes. Control operations accessed by the installer passcode are slightly different.
The Factory Default Code for User Code 1 is: 3 4 5 6 (Master Code)
(If the six digit code option is enabled, User Code 1 default will then be: 1 2 3 4 5 6)
The user code may be used for functions in a specific area or system-wide. Some options may be performed at any time,
even while the control is fully or partially armed. The menu system is designed to be next-step-oriented. After a brief
explanation of the options, the user should be able to begin operating the system immediately. For purposes of discussion,
the installer and the end consumer are both considered users, but have different capabilities.
2.4 Installer Program Code and Authorities
The installer code can access all the keypad user menus, including of course menu 9 - Installation Programming. The
Installer code also has limited arm/disarm privileges. It may be used to arm any area and may be used to disarm any area,
so long as that area was armed specifically by the installer code. The Installer code cannot disarm if an area was armed by
any user code. The Installer code may be used to silence 24hr alarms or a Burglary alarm in an area that was armed by the
installer or in an area that is not armed. The installer code may also be used to silence a trouble condition in a disarmed
area. See User’s Guide for a full description of arming and disarming procedures.
The Factory Default Installer Program Code is: 1 7 2 8 3 9
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 13
2.5 Keypad Overview
Ready Light - This light is ON when all burglar zones are secure and the system is OK for arming. If this light is OFF, one or more zones are
violated (not secure). For maximum security, all zones should be secured before the system is armed.
If FLASHING, one or more force-armable zones are violated. Force arming temporarily excludes violated zone(s) from the system. However, if
a force armed zone becomes secure while the system is armed, it will automatically restore to service. This is handy for a garage door. The
system may be armed with the door up, but once the car is backed out and the door is closed, it will become secured.
Armed Light- This light will be ON when the system is armed. The mode of arm will be indicated by the LCD display and the Exit or Stay
lighted pushbuttons. This light will be OFF when the system is disarmed.
Exit Key - This lighted key may be programmed for single or double press arming to the AWAY (not occupied) mode. If the Exit light is ON the
system is armed and all perimeter sensors and interior motions are active. The Away key may be pressed during the exit delay time t to
convert from Away mode to Away Vacation mode. The Away Vacation mode is primarily for use with the Whenever/And/Then Rules programming of Elk-RP to invoke long term energy savings.
Stay Key - This lighted key may be programmed for single or double press arming to the STAY (occupied) mode. If the Stay light is ON the
system is armed and all interior zones are excluded (bypassed). Only perimeter doors and windows are active in the Stay mode. This key
may also be programmed to change to other Stay modes such as: Stay Instant, Stay Night, and Stay Night Instant. Since interior zones are
automatically excluded once the Stay mode is activated, the M1 allows this key to Stay arm even while one or more interior zones are
violated, provided they are programmed for “force arming”. The Stay Night mode re-activates any interior night zones. To prevent a false
alarm the control will not allow change to the Stay Night mode when a interior night zone is violated unless it is programmed for “Force arm”.
Chime Key - Chime produces an audible tone alert whenever certain doors, windows, or other selected zones are violated. There are two
selections: Tone only and Off. Whenever Chime in On the Chime key will be illuminated. In the programming mode the Chime key also
functions as an insert character key for text programming.
Bypass Key - Pressing this key followed by a zone number and the bypass key again will exclude or bypass the selected zone. This
key may also be used to delete a character during text programming. When the Bypass key is lit, one or more zones are bypassed.
* Key - This key serves as a clear or reset key. If an error is made while entering digits, pressing this key clears the error. Three presses is
a master clear.
# Key - This key is currently a duplicate of the Bypass key.
Numerical Keys - These keys are used for entry of passcodes, programming, etc. Keys 2 - 9 also have an assigned alpha character
which are used for entering text.
Arrow Keys - The ELK and arrow keys have powerful functionality used for both normal operation and programming. Pressing the ELK
key displays relative information according to each application. The arrow keys allow scrolling through all available options. The user can
activate or select the displayed option by pressing the right arrow key. Once an option has been selected, the user may be prompted for
a passcode. Additional sub-menu options may appear to assist. The user may return to the status screen by pressing the * key.
Page 14
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
Keypad Menus
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
READY TO ARM
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
9:00AM 08/01/03
123456789012345678901234567890
123456789012345678901234567890
The control offers extended Menu Options via the center navigation “ELK” key. Some menus
may require a valid code to authorize. The Factory Default Code for USER Code 1 is: 3 4 5 6
(1 2 3 4 5 6 if the six digit code option is enabled)
Access to menus 1 to 5 can be restricted via programming to only Users that have “User Code Option 8” set. Menus 6, 7, and
8 required a Master or Installer Code. Menu 9 requires the Installer Code. Press ELK to begin, then press the UP or DOWN
arrow key to select a menu. Enter a code if prompted. To select a menu press the RIGHT arrow key.
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1-View/Control r
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
Automation Fncts
1234567890123456789012345678901
1234567890123456789012345678901
Allows viewing or controlling of the automation functions such as Tasks, Lighting, Outputs,
Temperature Sensor, Keypad Temperature, and Thermostats. Press the RIGHT arrow key to
select, then choose the desired function using the UP or DOWN arrow keys.
NOTE: The automation functions must be assigned and named using the ELK-RP software.
In most cases they cannot do anything unless they have been written into one of the
“Whenever/And/Then” automation rules.
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
1-Tasks
r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Water The Lawn
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
01: # Activates
123456789012345678901234567890
Tasks are like 1 button macros, performing multiple jobs with one push. To activate a task
press the RIGHT arrow key and press UP or DOWN to scroll through the list of available tasks.
To jump directly to a particular task, enter it’s two digit number. Once the task is displayed, all
it takes to activate it is to press the # key. A rule to use the “Water the Lawn” task might be:
WHENEVER “Water the Lawn” IS ACTIVATED THEN TURN ON Valve 19 FOR 5 MINUTES, etc.
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
2-Lighting
r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Kitchen Lights
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
001:=Off, # to Chg
123456789012345678901234567890
123456789012345678901234567890
Lighting allows the individual control of lights and/or appliances which have been assigned
through the ELK-RP software. Press the RIGHT arrow key to select Lighting, then press the
UP or DOWN arrow keys to scroll through the list. If you know the three digit number, you may
enter it to jump directly to that Lighting/Appliance. The current state of the unit will be
displayed. Press the # key to toggle (change) the unit from on > off or from off > on.
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
3-Outputs
r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
Pump Motor Cntrl
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
001:=Off, # to Chg
1234567890123456789012345678901
Outputs might be relays or voltages used to actuate something like a motor, fan, pump, etc.
Outputs can be turned on or turned off from this menu. Press the RIGHT arrow key to select
Outputs, then press the UP or DOWN arrow keys to scroll through the list. If you know the
three digit number, you may enter it to jump directly to that Output. The current state of the
output will display. Press the # key to toggle (change) the output from on > off or from off > on.
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
4-Temperature r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Sensor
123456789012345678901234567890
123456789012345678901234567890
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
Outside
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
S01:=032 Degrees
1234567890123456789012345678901
1234567890123456789012345678901
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
5-Keypad
r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Temperature
123456789012345678901234567890
123456789012345678901234567890
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
Keypad 01
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
K01:=073 Degrees
1234567890123456789012345678901
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
6-Thermostat
r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Temperature
123456789012345678901234567890
123456789012345678901234567890
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
Hallway
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
T01:=072 Degrees
1234567890123456789012345678901
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
2-Reset
r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Smoke Detectors
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
5 Seconds Smoke
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Output Reset
r
123456789012345678901234567890
Continued on next page..
Remote “Zone” Temperature Sensors can be read from this menu. Press the RIGHT arrow
key to select this menu, then press the UP or DOWN arrow keys to scroll through the list of
available sensors. To jump directly to a particular sensor enter it’s two digit number. The
current temperature will be displayed. Press the * key to exit.
Keypad Temperature Sensors can be read from this menu. Press the RIGHT arrow key to
select this menu, then press the UP or DOWN arrow keys to scroll through the list of available
keypads. To jump directly to a particular keypad enter it’s two digit number. The current
temperature at the keypad will be displayed. Press the * key to exit.
Thermostats can be read from this menu. Press the RIGHT arrow key to select this menu,
then press the UP or DOWN arrow keys to scroll through the list of available thermostats. To
jump directly to a particular thermostat enter it’s two digit number. The current temperature at
the thermostat will be displayed. Press the * key to exit.
Used for resetting latched smoke detectors after a fire alarm activation..
Press the RIGHT arrow key to actuate the Reset Smoke Detector feature. This causes the
power to smoke detectors to be removed for 5 seconds. During this time all fire zones will be
ignored to keep an accidental alarm from occurring.
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 15
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
3-Walk Test Area r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
< Area? Name >
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
000of016 Tested r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
A?-Violate Zones
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
4-View History r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Log
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
b08:00
L001:01/01b
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
AreaArmed
103A1
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
5-View Status
r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
of all zones
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
6-Change
r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
User Codes
123456789012345678901234567890
123456789012345678901234567890
Requires Master or
Installer
Code
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
b
123456789012345678901234567890
001:Selb
Prgr
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
< User Name >
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
7--Automation
r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Custom
Settings
123456789012345678901234567890
Requires Master or
Installer Code
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
b00:00Timer
CS01:b
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Sprklr On
123456789012345678901234567890
123456789012345678901234567890
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
8-System
r
1234567890123456789012345678901
1234567890123456789012345678901
1234567890123456789012345678901
Settings
1234567890123456789012345678901
1234567890123456789012345678901
Requires Master or
Installer Code
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
81-Set Sys Clock r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
24hr format
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
82-Not Used
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Menu 3 permits a local walk test of all zones assigned to this keypad’s area. The siren(s) and
communicator are disabled during a walk test. Press the RIGHT arrow key to begin a Walk
Test. The keypad displays the total tested zones adjacent to the total number of zones involved.
When a zone is activated, it’s name is displayed across the bottom and can be audible if the
Chime mode is on.
Allows viewing of the past 512 activities stored in the history log. Press the RIGHT arrow key to
view the History Log. History activities include: Arm, Disarm, Alarm, Trouble, etc. The top line
displays the Log number, Mth/Day, Time, and event description.
L001 is always the most recent event. Press the UP or DOWN arrow keys to move forward and
back. Event 512 will be the oldest event. The bottom line displays the event description, the
extended data (zone, user, etc.) and the area number (A1-A8).
Allows viewing of the current status of all zones. Press the RIGHT arrow key to select. Press
UP or DOWN to scroll through the zones or enter a three digit number to jump directly to a
particular zone. I.E. for zone 8 enter 008. Press the * key to exit.
For changing a user code and/or name for codes which have been previously enabled by the
Installer. Only a Master code OR the installer code can access this menu. Press the RIGHT
arrow key to begin. Press UP or DOWN keys to locate a user, or enter 3 digits to jump. Press
RIGHT arrow key to view the existing code. To change, enter the new code digits and listen for 3
beeps to confirm. To edit the name, press the RIGHT arrow key once, then press the DOWN
arrow key. Enter the text using the letters on the keys. I.E. For “K” press the 5 key twice. Move
RIGHT or LEFT with the arrow keys. Press Chime to insert a space. Press Bypass to erases a
letter. The UP and DOWN arrow keys shift from upper to lower case letters. Press the ELK key
to save and exit.
.
Allows an end user to change up to 20 settings incorporated into an automation rule. These
settings can be: time of day, time duration (seconds), or a numeric value. Each custom setting
has a reference number (CS) and a text description: I.E. CS01: Sprkl On 00:00 [Time] implying
a time of day setting. Press the RIGHT arrow key to begin.
Press the UP or DOWN arrow keys to locate a setting, then press the RIGHT arrow key to
select. Enter the new value and press the ELK key to save and exit.
Menu 8 consists of 8 sub-menus used for advanced system settings. Press the right arrow key
and enter a valid user code. Press the UP or DOWN arrow keys to select a sub-menu or enter
the one digit number to jump directly to any sub-menu. I.E. enter 6 to jump to 86.
To set the system clock press the RIGHT arrow key, then press the UP or DOWN arrow key to
select the day. Next, press the RIGHT arrow key to move to Date/Time setting. Enter two digits
for month, date, year, hour, and min. To exit press the * key.
123456789012345678901234567890
123456789012345678901234567890
To set keypad adjustments press the RIGHT arrow key. Then press the UP or DOWN keys to select
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
83-Keypad
r
123456789012345678901234567890
one of the three options.
123456789012345678901234567890
123456789012345678901234567890
Adjustments
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
1:Set Keypad
r To set keypad beep tones press the RIGHT arrow key, then select the desired tone using the UP or
123456789012345678901234567890
123456789012345678901234567890
DOWN keys. There are 9 settings (0-8). When done, exit by pressing the * key.
123456789012345678901234567890
Beep Tone
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
2:Set Keypress r To set key-press beep volume press the RIGHT arrow key, then select the desired volume using
123456789012345678901234567890
123456789012345678901234567890
the UP or DOWN keys. There are 7 volume levels (1-7) plus Off (0). To exit press the * key.
123456789012345678901234567890
Beep Volume
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
To set backlight dim level press the RIGHT arrow key, then select the desired level using the UP or
123456789012345678901234567890
123456789012345678901234567890
3:Set Backlight r
123456789012345678901234567890
123456789012345678901234567890 DOWN keys. There are 9 backlight levels (1-9) plus Off (0). The keypad automatically dims to this
123456789012345678901234567890
Dim
Level
123456789012345678901234567890 setting after 30 seconds of no activity in order to save energy. To exit press the * key.
Page 16
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
84-System
r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Tests
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
1:Battery Test
r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
for 30 Seconds
123456789012345678901234567890
123456789012345678901234567890
To perform system tests press the right arrow key. Then press the up or down arrow keys to
select one of the three tests.
The control’s standby battery is load tested automatically every 24hrs. However, it can also be
manually load tested anytime using this option. Press the right arrow key to start the test. The
battery is placed under load for 30 seconds and the battery voltage and system current is
displayed. If the battery falls below a set level, a Low Battery trouble will occur. If it’s necessary
to replace the battery, this test should be used to test and clear a Low Battery Trouble condition.
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
2:LCD Test
r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
3:Communicator r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Manual Test
123456789012345678901234567890
123456789012345678901234567890
To test the keypad’s LCD screen press the RIGHT arrow key. The entire screen should appear
black indicating all pixels are working. To exit press the * key.
To manually test the communicator (dialer) press the RIGHT arrow key. Testing is done using
the first phone number that is programmed to send a test code. If there is no phone number
programmed to send a test code, the test will end. To exit this menu press the * key.
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Send Test
r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Silently
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Clear Pending r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Dialer Reports
123456789012345678901234567890
123456789012345678901234567890
There are two types of test, silent and monitored. To silently send a test press the right
arrow key from this display. To hear the test using the inside speakers (OUT1) press the up
or down arrow key to bring up the following display.
This special option allows any pending (not reported) dialer communications to be cleared
or cancelled. Typically this will be used only for initial installation and testing.
NOTE: ALWAYS NOTIFY THE MONITORING STATION BEFORE TESTING THE DIALER! If the test
should fail, a Comm Fail trouble will occur. To clear a Comm Fail the dialer must be able to
complete a good communication.
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
85-Connect ‘RP’ r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Remote Program
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
1:Seize Line
r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Attended Mode
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
2:Seize Line
r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
UnAttended Mode
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
86-System
r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Diagnostics
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
1:DataBusErrors b
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
T2A1 Retry 00000
123456789012345678901234567890
123456789012345678901234567890
To connect ELK’s Remote Program PC software (RP) via the user assisted method, press the
RIGHT arrow key and then select the connection mode with the UP or DOWN arrow keys.
1:Seize Line Attended Mode - 1) Allows RP connection to begin on an already established voice
connection between the control phone line and the RP Computer. 2) Also useful for manually
answering an incoming call from the RP Computer with programming Rings to Auto Answer.
2:Seize Line Unattended Mode - Pressing the RIGHT arrow key causes the control to dial the
programmed RP telephone number. The RP Computer must be in the “wait for call” mode.
This is a collection of tools for diagnosing system problems. Press the RIGHT arrow key and
enter a valid user code to begin. Press the UP or DOWN keys to select one of the four tools:
This tool is useful for determining if data bus errors are accumulating. It displays the device
type and number of retries accumulated since the last power-up.
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
2:Sys Volt/Curr b
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
13.8V 0.440Amps
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
3:Zone=001 Volts
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Display Level
r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Zn=001 Volt=07.2
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
L04.6 H09.0 A132
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
4:LastOnHookTele
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Line V=57,+-20%
123456789012345678901234567890
123456789012345678901234567890
This tool displays the control’s voltage and the average current being drawn from the power
supply.
This tool allows the voltage on each zone to be displayed in real time. It changes as contacts
or devices are violated. Press the RIGHT arrow key to begin.
Use the UP or DOWN keys to scroll through each zone. The displayed information consists of:
the present zone voltage, the L low and H high alarm thresholds, and the analog (A to D)
equivalent of the zone voltage..
This is a read only screen displaying the telephone line voltage during the last on-hook
condition. It is an approximate measurement accurate to only +-20%.
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 17
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
9-Installation
r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Programming (0)
123456789012345678901234567890
123456789012345678901234567890
From this menu you may press the RIGHT arrow to enter Installation Level Programming. If
the Installer Programming Code has not already been entered it will be required at this
time. REFER TO PAGE 20 FOR PROGRAMMING INSTRUCTIONS
Requires
Installer
Code
NOTE: The ElkRP software can be used to lockout certain local program capabilities for “anti-takeover” purposes. The
number in the lower right corner of this menu will indicate the level of lockout as follows: (0) = No lockout, (1)=Lockout
Telephone number programming - view everything, (2)=Lockout ALL programming - view everything, (3)=Lockout ALL
Programming and Viewing. This can only be set or removed from the ELK-RP Remote Programming Software.
Menu 0 - Select Keypad Alternate Area - Multi-area (Partition) Operation
This menu allows the keypad to be mapped temporarily to any other area, allowing multi-area (partitioned) operation. An individually mapped area can be armed, disarmed, and controlled just as if the keypad were permanently
assigned to that area. It may also be used to access a consolidated display of all areas at once, showing the
status of each area.
To reach the keypad menus press the center navigation key labeled “ELK”. A user code may be required depending on how the control is programmed. The four arrow keys around the Elk key are used to scroll, backup, etc.
Pressing the RIGHT arrow key will select the displayed menu.
1.
2.
Press the ELK key. Enter a user code if prompted.
Use the UP or DOWN arrow keys to find menu “0-Select Keypad Alternate Area”.
1234567890123456789012345678
1234567890123456789012345678
1234567890123456789012345678
1234567890123456789012345678
0-Select Keypad
1234567890123456789012345678
1234567890123456789012345678
1234567890123456789012345678
Alternate Area r
1234567890123456789012345678
1234567890123456789012345678
1234567890123456789012345678
1234567890123456789012345678
1234567890123456789012345678
1234567890123456789012345678
1234567890123456789012345678
Auth. Required
1234567890123456789012345678
1234567890123456789012345678
1234567890123456789012345678
Enter Valid PIN
1234567890123456789012345678
1234567890123456789012345678
1234567890123456789012345678
Press the RIGHT arrow key to select this menu and display the following:
Enter a valid user code. The control does not allow (restricts) mapping or viewing of
areas that are not authorized for the user code.
MAPPING TO AN INDIVIDUAL AREA
Enter an area number from 1 to 8 OR scroll UP and DOWN with the arrow keys.
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
ChangeKPArea-1 r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
[Area Name] A1
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
ChangeKPArea-0 r
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
0=All Areas
123456789012345678901234567890
123456789012345678901234567890
12345678901234567890123456789
12345678901234567890123456789
12345678901234567890123456789
12345678901234567890123456789
12345678901234567890123456789
Area# 1 2 3 4 5 6 7 8
12345678901234567890123456789
12345678901234567890123456789
Status X r r r r r r r
12345678901234567890123456789
12345678901234567890123456789
12345678901234567890123456789
Press the Right Arrow key to map the Keypad to the area shown. The LCD display and
the Ready / Armed LEDs will show the status for the mapped area for 1 minute. During
this minute, it is possible to arm, disarm, bypass, etc. the mapped area from this
keypad. Each time a key is pressed the 1 minute is restarted. However, after 1 minute
of no keypress activity, the keypad will return to its original primary assigned area.
ACCESSING A CONSOLIDATED DISPLAY OF ALL VALID AREAS
Entering “0” for the area number immediately maps the Keypad to a consolidated
‘snapshot’ of all authorized areas. This permits quick arming and disarming only. If an
area is not ready to arm it will be necessary to map individually to that area to view the
violated zone(s) and either secure or bypass them prior to arming.
This example shows all 8 areas, meaning that the User Code was valid for all 8.
The display only shows the areas for which the user code is authorized.
Note the letter beneath each area number.
The single upper case “X” indicates the primary area. This area is controlled exclusively from
the regular operation screens.
A lower case “r” below an area indicates the area is Ready to Arm.
A lower case “n” below an area indicates the area is Not Ready.
A upper case “A” below an area indicates the area is Armed.
This example shows the user code was only authorized for areas 1, 2, and 3. The
unauthorized area(s) have a “-” below them.
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
Area# 1 2 3 4 5 6 7 8
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
Status X r r - - - - - r
12345678901234567890123456789012
12345678901234567890123456789012
To change or ‘toggle’ the arm status of an area, press the number key representing
the area number. IMPORTANT: The area status is not “real time”. It is a snapshot
taken when the RIGHT arrow key was pressed. If a zone has since become violated
the area will still be displaying “r”, however the letter will immediately change to “n”
and the keypad will emit an error tone when an attempt is made to arm by pressing
the area number.
When finished, press the “*” key to exit.
Page 18
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
Section 3 - Programming The Control
3.1 Introduction
The Security functionality of the Control can be programmed either from an ELK-M1KP LCD Keypad OR from the ELK-RP PC
Software. The keypad features a menu-driven “Text” based interface with simple Yes/No answers for most options. After just
a short amount of experience the average installer will not even require an instruction manual to keypad program the control.
For the Automation functionality the ELK-RP PC Software is a requirement. The options and capabilities available for
automation are so unique and powerful that it takes a PC to make use of all the benefits. The control features a powerful
“Whenever/And/Then” RULES based programming that allows almost any imaginable operation.
3.2 Local Keypad Programming
There are two levels of operation for programming the control locally, user level and installer level.
- User level programming provides the ability to add, change, or delete user passcodes and names. It also allows custom
automation settings to be viewed and changed. A master user code is required to access the user code and custom settings
screens. User programming is explained in the User’s Guide.
- Installer level programming allows total customizing of the Security operating features. Only the installer code may access
this level. If the installer code is lost or forgotten, it is impossible to program the control locally. Anyone attempting installer
level programming should be familiar with the contents of this publication prior to programming the control panel. If remote
programming is used, it is possible to “lock out” or prevent takeover of a control by another installation company by selecting
“Lockout Local Prog.” This prevents the installer passcode from gaining access to programming via an LCD keypad. The
installer passcode may still be used for the non-programming functions described in Chapter 2. Lockout Local Prog does not
affect remote programming.
3.3 Local or Remote Computer Programming (ELK-RP) and Anti-Takeover
ELK-RP programming utilizes extensive error checking and security safeguards, including data encryption, password log-on,
serial number, and dealer assigned RP access code. The serial # identifies the control to RP while the RP access code
identifies the computer to the control prior to a programming session. RP loads the access code during the first connection. It
cannot be viewed or changed from local keypad programming. In addition to these safeguards, you can set an anti-takeover
option from RP which prevents certain keypad programming. Even a total default of the panel programming cannot reset the
anti-takeover option once it is set..
The Factory Default Elk-RP Access Code is: 2 4 6 8 0 1
3.4 Area Partitioning
The control may be divided into 1 to 8 independent areas (partitions). Each area appears as a full-featured system, allowing
one control to be shared by multiple, independent departments within a common structure. Zones, User Codes, and
Keypads may be assigned to any 1 area up to the maximum number available. An example is a single business divided into
separate departments, each department occupied by different employees. Mount the control in a secure area (common utility
closet) with dedicated and uninterrupted AC power and telephone service. Then assign zones, codes, and keypads to each
department.
The Alarm Output (Output 2) activates on all alarms, regardless of the area. The RP Software Rules can be used create
additional (separate) outputs. When reporting to the central station events like AC Power Failure, Automatic tests, Low Battery,
etc., are considered system reports and are transmitted using the Area 1 account number. If area partitioning is not desired,
simply designate all zones to a single area (Area 1) which is the factory default setting for zones 1-8.
COMMON AREA - Another popular feature is the ability to have one or more areas made “common” to Area 1. This is often
referred to as a “Vestibule Feature”. Any of the Areas 2 thru 8 may be made common to Area 1. The result is: Area 1 cannot be
armed until all its common areas are armed. Once armed, Area 1 will disarm if any common area becomes disarmed. This
is good for lobbies or vestibules shared by two or more businesses. Each business must have their own area keypad.
NOTE: If you want Area 1 to automatically arm when all its common areas become armed, use a Whenever/And/Then rule
from the RP software to do this.
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 19
3.5 Communicator Setup Checklist
The Communicator (Dialer) can dial up to 8 telephone numbers in addition to the RP computer. Digital reporting formats
include: Pulse 4+2, SIA, Contact ID, and Pager. Use the following checklist for each required telephone number.
1.
2.
3.
4.
5.
6.
Under Menu 08 - Telephone Account Setup, select one of the telephone numbers and program the following:
Option 01: Select the desired reporting format - 0=Disable, 1=Contact ID, 2=SIA, 3=Pulse 4+2, 4=Pager.
Option 02: Set the priority for the first (primary number) to 0 = Always Report.
Option 03: Program the telephone number digits to be dialed. No special start or ending characters are required.
Option 04: Set the dial attempts to greater than 0. For Digital reports 8 is suggested.
Option 05 Program the digits for the account number to report. Each area (partition) has its own Acct. Number.
Option 13: Select Yes to have Area info, Zone Alarms, Zone Restores, and Zone Unbypasses reported to this Tel #.
Option 14: Select Yes if you wish to have Zone Bypasses reported to this Tel #.
Option 15: Select Yes if you wish to have Zone Troubles reported to this Tel #.
Option 16: Select Yes if you wish to have User (Open/Close) Reports reported to this Tel #.
Option 17: Select Yes if you wish to have Global System Events (AC Fail, Low Battery, etc.) reported to this Tel #.
Option 18: Although not required, you may program a text name for each telephone number.
Under Menu 09 - Area Reporting Codes, select the area (partition) and program the desired options such as: Dialer
Delay, Alarm Abort, Auto Open/Closings, etc. then .
Under Menu 10 - Zone Reporting Codes, select the zone number and program the desired options such as: Zone Alarms,
Restores, Bypasses, or Trouble.
Option A: For Zone Alarm program a two digit code. To have the automatic SIA or Contact ID report codes transmitted
simply program a nonzero value. I.E. Program a 1 (01).
Option R: For Zone Restore program a two digit code. For automatic SIA or Contact ID codes program a 1 (01).
Option B: For Zone Bypass program a two digit code. For automatic SIA or Contact ID codes program a 1 (01).
Option T: For Zone Trouble program a two digit code. For automatic SIA or Contact ID codes program a 1 (01).
Under Menu 11 - F Key Reporting Codes, select and program the alarm code for each desired Keypad Panic Key. NOTE:
Keypad Panics only have Alarm report codes, they do not have restore codes. For automatic SIA or Contact ID codes
program a 1 (01).
Under Menu 12 - Sys Report Code Options & Codes, select and program each desired option such as: AC Fail, Low
Battery, Automatic Test, and other system wide options, including the time values for certain options. For automatic SIA or
Contact ID report codes program a 1 (01).
Under Menu 13 - User Report Codes, select and and program an Open or Close report code for any User(s) that you
wish to track arm/disarm events, including arm/disarm by the Installer Code or Elk-RP computer.
3.6 Entering Installer Level Programming
1.
Press the center ‘ELK’ key once followed by the DOWN arrow key until display reads “9-Installation Programming”. NOTE:
The keypad may beep and display the following:
123456789012345678901234567890121234
2. Enter the Installer Program Code when required.
Press the right arrow key to select the “Installation Programming” option.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Auth. Required
Enter Valid Pin
The Factory Default Installer Program Code is: 1 7 2 8 3 9
For security against unauthorized programming changes, the installer code should be changed from its factory default setting.
This can be done from Menu 07 - Globals System Definitions, Option 42.
Once the Installer Code has been entered, the first programming menu will display and a 4 minute timer will be started.
If there is no key-press activity during this time period the control will automatically exit from the programming mode. It
is easy to navigate around and between the programming menus and options using the up and down arrow keys. When
the correct menu or option is located, press the right arrow key to proceed into that menu.
Refer to the Quick Reference Guide on the following page to locate a particular menu or to see what options
appear under each menu. Refer to the individual menus and their option descriptions for details about each of the
programmable items.
Page 20
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
M1EZ8 Installation and Programming
Menu 02
User Code Auth.
User 1
(1) Area #
(2) Arm
(3) Disarm
(4) Bypass
(5) Access
(6) Temporary
(7) Master
(8) Menu 1-5
(9) Duress
(10) [Name]
Enrolling
-Disp Totat Modules
-Allow Module Edit
Menu 01
Bus Mod Enroll
Menu 03
Area Defs
Area 1
(1) Exit Delay 1
(2) Entry Delay 1
(3) Exit Delay 2
(4) Entry Delay 2
(5) Auto Stay
(6) Exit Restart
(7) Closing Ringback
(8) SglKey Quickarm
(9) DblKey Quickarm
(10) StayKeyScroll
(11) Stay Instant
(12) Night Scroll
(13) Night Instant
(14) StayChgArmed
(15) [Name]
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
Page 21
Menu 05
Zone Defs
Zone 1
(1) Definition
(2) Type
(3) Area Assign
(4) Silent Alarm
(5) Dialer Delay
(6) Listen-In
(7) Bypass
(8) Force Arm
(9) Swinger
(10) Per. Trip
(11) Fast Loop
(12) Chime
(13) Cross Zn
(14) [Name]
Menu 04
Keypad Defs
Keypad 1
(1) Area Assgn
(2) Silent Entry
(3) Silent Exit
(4) Silent Chime
(5) Dark in 60 sec
(6) Show Date/Time
(7) Show Temp
(8) Show Area
(9) Byp Req Code
(10) F1 Key Def.
(11) F2 Key Def
(12) F3 Key Def
(13) F4 Key Def
(14) F5 Key Def
(15) F6 Key Def
(16) [Name]
Menu 07
Global Options
(1) Tel Remote
(2) 12hr TimeDisp
(3) DD/MM Disp.
(4) Celcius Disp.
(5) DST Observe
(6) Fast Loop Tm
(7) SlowLoop Tm
(8) Cross SelfVer
(9) Cross Zn Tm
(10) Aud Trbls
(11) 6 digit codes
(12) CodeLockout
(13) Common Area
(14) Out2 Yelp to Buz
15 thru 25 Not Used
Menu 06
Cutoff Timers
(1) Burglar
(2) Fire
(3) Medical
(4) Police
(5) Carbon Mon
(6) Emergency
(7) Freeze
(8) Gas
(9) Heat
(10) Water
(11) Aux1 24hr
(12) Aux2 24hr
(95) Default Wireless Definitions
(99) Default Entire Control Panel
Menu 07
Global Options (cont.)
(26) Out 2 Change to Voltage
(27) Out 2 Delay Time
(28) Out 2 Sgl Alarm Lockout
(29) Rings til Answer
(30) Ring/Hang/Answer
(31) 2 Way Listen-in Enable
(32) 2 Way Callback Time
(33) CS Alm Verify Time
(34) Baud Rate Port 0
(35) Xmit Event Log
(36) Xmit Zone Changes
(37) Xmit Output Changes
(38) Xmit Task Changes
(39) Xmit Light Changes
(40) Xmit Keypad Keys
(41) Req Code User Menus 1-5
(42) Local Prog. Code
(43) Serial Number [Read Only]
(44) Software Ver. [Read Only]
(45) Default Control Options
(81) Default User Codes
(82) Default Areas Data
(83) Default Keypads Data
(84) Default Zones Data
(85) Default Zone Names
(86) Default Cutoff Timers
(87) Default Global Data
(88) Default Telephone Data
(89) Default Telephone Numbers
(90) Default Area Report Codes
(91) Default Zone Report Codes
(92) Default System Report Codes
(93) Default User Report Codes
Menu 09
Area Report Codes
Area 1
(1) Dial Delay Time
(2) Abort Code
(3) Cancel Time
(4) Cancel Code
(5) Close Auto
(6) Close Early
(7) Close Extended
(8) Fail to Close
(9) Late Close
(10) Keyswitch Close
(11) Duress Code
(12) Open After Alarm
(13) Open Early
(14) Fail to Open
(15) Open Late
(16) Keyswitch Open
(17) User Lockout
(18) Exit Error
(19) Fail to Comm
Menu 08
Telephone #’s & Accts
Telephone #1
(1) Always Report
(2) Number
(3) Format
(4) Attempts
(5) Acct #1
(6) Acct #2
(7) Acct #3
(8) Acct #4
(9) Acct #5
(10) Acct #6
(11) Acct #7
(12) Acct #8
(13) Report Area/Alm
/Rest/Unbypass
(14) Report Zn Bypass
(15) Report Zn Troubles
(16) Report User Op/Cl
(17) Report Sys Globals
(18) [Name]
ELK-EZ8 QUICK REFERENCE - MENU PROGRAMMING
Menu 12
System Rpt Codes
(1) AC Fail Delay
(2) AC Fail Code
(3) Auto Test Code
(4) TstTime hr:mm
(5) Days betweenTest
(6) Not Used
(7) Exp Module Tbl
(8) Installer Begin
(9) Installer End
(10) Log 80% Full
(11) Low Battery
(12) Memory Error
(13) RP Download
(14) Tel Line Fault
(15) Output 2 Tbl
Menu 11
Keypad
Report Codes
Keypad 1
(1) F1 Key Alarm
(2) F2 Key Alarm
(3) F3 Key Alarm
(4) F4 Key Alarm
(5) F5 Key Alarm
(6) F6 Key Alarm
Menu 10
Zone Rpt Codes
Zone #1
Alarm Code
Restore Code
Bypass Code
Trouble Code
Menu 14
Wireless Defs
1: ReceiverOptions
(1) Receiver Size
(2) ZnBank(Start Zn)
(3) Reg Supv. Hrs.
(4) Fire Supv. Hrs.
2: Transmitter Opts
^ Select Transmitter
(1) Enable Xmtr.
(2) Supv. Type
(3) Enable Option 1
(4) Enable Option 2
(5) Keyfob User ID
3: Learn Transmitter
^ Select Transmitter
(1) Xmtr to Learn
(2) Push Xmtr
4: Keyfob Event Def.
(1) Button 1 Code
(2) Button 2 Code
(3) Button 3 Code
(4) Button 4 Code
(5) Button 5 Code
(6) Button 6 Code
(7) Button 7 Code
(8) Button 8 Code
User 101
- RP Computer
Upload/Download
(1) Open Code
Close Code
User 100
- Installer(1) Open Code
Close Code
Menu 13
User Rpt Codes
User #1
(1) Open Code
Close Code
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
01-Bus Module
Enrollment
r
Menu 01 - Bus Module Enrollment
Press RIGHT arrow key to select this menu. Press UP or DOWN arrow keys to select
another menu. The ELK key backs up one menu level. To exit press the * or Exit key.
NOTE: Every data bus device: Keypad, Input (Zone) Expander, Output Expander, etc. MUST have a unique
address within its type. This menu is then used to enroll the device into the system. SEE DETAILS BELOW:
Bus Module Enroll
Description of Option
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Press the RIGHT arrow key to select this menu and automatically start the bus enrollment
process. ALL data bus devices which are presently connected to the data bus should
become enrolled.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
The enrollment process only takes a few seconds. Once complete, this summary screen
will appear displaying the total number of bus modules that were found and enrolled. To
edit and/or view the devices individually, press the RIGHT arrow key one time.
Enrolling
Bus Modules
XX Bus Modules
Enrolled, Editr
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Keypad
Addr=01
T1 b
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Keypad
Addr=02
T1 b
lr
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
End Enrollment
0x Bus Modules
Each enrolled keypad/device can be viewed one by one. The first device will always be
Keypad 1 with a T1 (for type 1) and Addr=01 (for address 01). As explained below,
different kinds of devices can be identified by their device “Type”. Pressing the Up or Down
arrow keys will scroll through each enrolled device.
If a device is removed from the data bus, it should be removed by repeating the enrollment
process. The control will only enroll the devices that are connected. It will remove any
previously enrolled devices that it does not see.
After the last device is reviewed, the next press of the Up arrow key moves to the “End
Enrollment” screen which once again displays the total number of devices enrolled.
DATA BUS DEVICE TYPES AND ADDRESSES: Each data bus device is a specific “Device Type”. Keypads are TYPE
1, Input (Zone) Expanders are TYPE 2, Output Expanders are TYPE 3, Serial Port Expanders are TYPE 5. Any new
devices designed will be assigned a Device Type. Every data bus device MUST have a unique “Address” setting within
its type. Valid Input Expanders addresses are 2 to 13, Output Expander addresses are 1 to 13. The address determines
the starting and ending zone or output numbers for that expander. See chart below:
Addr Input Exp
1 = N/A (main bd)
2 = Zone 17-32
3 = Zone 33-48
4 = Zone 49-64
5 = Zone 65-80
Output Exp
Outputs 1-16
Output 17-32
Output 33-48
Output 49-64
Output 65-80
Addr
6=
7=
8=
9=
10 =
Input Exp
Zone 81-96
Zone 97-112
Zone 113-128
Zone 129-144
Zone 145-160
Output Exp.
Output 65-80
Output 97-112
Output 113-128
Output 129-144
Output 145-160
Addr Input Exp
11 = Zone 161-176
12 = Zone 177-192
13 = Zone 193-208
Output Exp.
Output 161-176
Output 177-192
Output 193-208
INPUT AND OUTPUT EXPANDER ADDRESSES: Locate the bank of four white (DIP) switches along the top edge of the
board. Each switch has a position of Off or On (0 or 1) and a binary value (1, 2, 4, 8). The addition of the binary values
(sum total) for the switches set to the On position determines the data bus address. For example: Data bus address 5
is set by placing switches 1 and 4 to the On position (1 + 4 = 5). All other switches must be in the down or Off position.
KEYPAD ADDRESSES: All keypads are factory set to address 1. Valid addresses are 1 to 16. The first keypad on the
system (Keypad 1) is automatically enrolled upon power up. Each additional keypad must be assigned a unique
address and then manually enrolled from “Menu 1 - Bus Module Enrollment”. To set the address on a keypad do the
following:
1. Hold down a key while applying power OR press and hold the (Asterisk) “ * ” and F5 keys for 5 seconds.
2. Press the F1 key, then use the UP or DOWN arrow keys to set the desired address number.
3. Press the EXIT key when done.
NOTE: If a device is removed from the data bus, it should be un-enrolled to prevent a trouble. To replace a
defective device, set the address to the same value as the old unit and initiate the Bus Enrollment process.
Page 22
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
02-UserCode Optn
Code used to:
r
Menu 02 - User Code Options
Press RIGHT arrow key to select this menu. Press UP or DOWN arrow keys to select
another menu. The ELK key backs up one menu level. To exit press the * or Exit key.
Default Code for User Code 1 is: 3 4 5 6 Note: If six digit code option is enabled, the
default will be 1 2 3 4 5 6. See Menu 07 - Global System Definitions, Option G11
User Code Options
Description of Option
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
There are 99 potential User codes. User 1 (001) is the first to display. Press the right
arrow key to program, or press the up or down arrow keys to select another user. Enter
three digits to jump to a specific user. The user name is displayed along the bottom.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
This option assigns the areas(s) in which this code may be used. For example: if the
numbers 1,2, & 4 are displayed, the code may be used in those areas. To assign or
remove an area press the numbers keys 1 thru 8. Each press toggles the number on/off.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
Selects Arm privileges. If Yes, this code can Arm it’s assigned area(s) (see option 01
above) from a keypad that is also assigned to the desired area. If No, this code cannot be
used to Arm.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
Selects Disarm privileges. If Yes, this user code can Disarm it’s assigned area(s) (see
option 01 above) from a keypad that is also assigned to the desired area. If No, this code
cannot be used to Disarm.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
A Yes allows this code to Bypass zones whenever Menu 04-Keypad Definitions, Option
09, “Byp Key Req PIN” is set to Yes. Code and Keypad must be in the same area.
Default value for both these options is No (code not required for bypass).
001: Selb
User 1
Prgr
001 01:12345678 r
Code used inArea
001 02:=Yes
Arm with Code
r
001 03:=Yes
r
Disarm with Code
001 04:=Yes
r
Bypass with Code
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
001 05:=No
r
Access with Code
A Yes allows this code to activate the Access Keypad Events 1313-1328 for the keypad
where code is entered. Use the Whenever/And/Then Rules from Elk-RP to assign an
output to this event for tripping a door strike or lock. Note: If this code is enabled for
arming, it will be necessary to press the Exit or Stay key to arm after the code.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
If Yes, this code can only disarm if the control was armed by it or another temporary code.
In other words: A temporary code cannot disarm the control if a regular code was used to
arm. A temporary code might be used for cleaning, repair personnel, etc.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
A Master Code can be used to review, change, or delete other users, and to modify
selected system options. Only one Master code is needed per system. For security
purposed, multiple Master codes are not recommended.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
001 08:=No
r
Menu 1-5 Allowed
When Menu 07 - Global System Definitions, Option 41, “Require Code User Menu 1-5” is
set to a Yes, this option is then used to set which codes are allowed to access Menus 1 5. NOTE: Menus 6, 7, and 8 are only available to a Master or Installer code.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
If Yes, this code will cause a silent Duress or “holdup” alarm to activate when the code is
used to arm or disarm the system. CAUTION: The communicator report code MUST
also be programmed! This feature is dangerous and should be used with caution.
001 06:=No
r
Temporary Code
001 07:=Yes
Master Code
001 09:=No
Duress
r
r
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
001 10:Usr Name l
User1
To edit the User (Name) text press the left arrow key. Enter text using the number keys.
I.E. For a “K” press the 5 key twice. To move the cursor, press the RIGHT or LEFT arrow
keys. The Chime key inserts a space, the Bypass key erases 1 digit. The up/down keys
to toggle between upper and lower case. Press the ELK key when complete.
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 23
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
03-Area
Definitions
r
Menu 03 - Area Definitions
Press RIGHT arrow key to select this menu. Press UP or DOWN arrow keys to select
another menu. The ELK key backs up one menu level. To exit press the * or Exit key.
Area Defintions
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
A1: Selb
Area 1
Prgr
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
A1 01:=060
r
Exit Delay1 Time
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
A1 02:=030
r
Entry Delay1Time
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
A1 03:=060
r
Exit Delay2 Time
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
A1 04:=030
r
Entry Delay2Time
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
A1 05:=No
r
AutoStay No Exit
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
A1 06:=Yes
r
Exit1TimeRestart
Description of Option
Of the 8 potential areas (partitions), Area 1 is the first to display. Press the right arrow
key to program, or press the up or down arrow keys to select another area. To jump to a
specific area enter the number (1-8). The area name is displayed on the bottom.
The amount of exit time in seconds for all zones programmed as Exit Delay 1. Range is
045 to 255 seconds. Default value is 060. NOTE: Due to the way force arm works, if
an Exit Delay 1 zone also has force arm enabled, its exit time will be the greater
of the time values for Exit Delay 1 or Exit Delay 2. Do not enable force arm on
Exit Delay 1 zones if this operation is not desired.
The amount of entry delay time in seconds for zones programmed as Entry Delay 1.
Range is 030 to 255 seconds. Default value is 030.
The amount of exit delay time in seconds for zones programmed as Exit Delay 2. Range
is 045 to 255 seconds. Default value is 060. See note above regarding force arm
and Exit Delay 1 zones.
The amount of entry delay time in seconds for zones programmed as Entry Delay 2.
Range is 030 to 255 seconds. Default value is 030.
If Yes, the control will switch from AWAY mode to STAY mode at the end of the exit delay
time if no exit zone is violated (no exit detected). NOTE: This tracks the longest of the
two exit timers. All interior zones are bypassed in the STAY mode. Default value is No.
If this option is set to Yes (default), the exit procedures will be affected in three ways:
1) ADDITIONAL EXIT1 “GRACE” FEATURE - During the initial Exit Delay 1 time if the
zone violates a second time and restores, the exit timer will automatically restart one
time. I.E. If the Exit1 door is opened, closed, and then opened again the timer will restart.
NOTE: This only works on Exit Delay 1 zones and the timer only restarts one time.
It does NOT work if the zone is enabled for force arm! This features complies with
the SIA CP-01 false alarm reduction standard.
* SIA
CP-01
2) SPOUSE “LEAVE FOR WORK” OR “LET PET OUT” FEATURE - If the system is
armed in one of the Stay modes, a User may press the Exit key to re-start the exit delay
time in order to open an exit/entry door and leave for work. The system remains in the
Stay mode for remaining family members that are still in the house. This can also be
used to let a pet outdoors. When the pet is ready to come back inside the User simply
presses the Exit key again to restart the timer.
3) GOING FROM STAY MODE TO AWAY MODE - If the system is armed in one of the
Stay modes, a User may change the arm mode to Away. This is done by pressing the
Exit key twice in short succession (within 3 seconds) and leaving the building.
Exit Error If an entry/exit zone is violated at the time the Exit Delay time expires, the Exit Error Feature will be * SIA
CP-01
activated. The local siren will sound immediately and the Entry Delay warning will begin. If the control is not
disarmed before the Entry Delay expires, the communicator will report the alarm along with an Exit Error code,
provided these codes are programmed. An Exit Error event flag will also be set which can be used by the
“Whenever/And/Then” rules (refer to the ELK-RP software) to sound a siren, or blink a light, or whatever.
Exit Error feature complies with the SIA CP-1 false alarm reduction standard.
Page 24
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
Menu 03 - Area Definitions (continued)
Area Definitions
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
A1 07:=No Sendr
Closing Ringback
Description of Option
If Yes, a Closing Ringback signal (otherwise known as closing report successful) will be
sent to all the keypads when the Communicator transmits a closing report and the Central
Station Receiver kissoff (acknowledgement) is received. The Exit Delay time will be
restarted at this time. The default value is No.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
If Yes, the control can be armed by a single press of the Exit or Stay keys. No code is
required except to disarm. Note: This option cannot be set to Yes if “Dbl Key Quick
Arm” (see below) is set to Yes. The default value is Yes.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
A1 09:=No
r
DblKeyQuickArm
If Yes, the system can be armed by a double press of the Exit or Stay keys. The second
press must follow the first very quickly. Note: This option cannot be set to Yes if “Sgl
Key Quick Arm” (see above) is set to Yes. The default value is No.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
A1 10:=Yes
r
Stay Key Scroll
If Yes, the Stay key may be pressed during the exit delay time to scroll (step) through the
selected levels of Stay arming. I.E. Stay Instant, Stay Night, etc. The options below
select the levels that will be available. The default value is Yes.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
If Yes, AND option 10 is set to Yes, multiple presses of the Stay key during exit delay will
be able to scroll to the Stay Instant arming level. The default value is No.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
If Yes, AND option 10 is set to Yes, multiple presses of the Stay key during exit delay will
be able to scroll to the Stay Night arming level. The default value is Yes.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
If Yes, AND option 10 is set to Yes, multiple presses of the Stay key during exit delay will
be able to scroll to the Stay Night Instant arming level. The default value is No.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
This option should be used with caution. If Yes, the Stay key may be used to scroll or
step the armed level after exit delay has expired and the control is fully armed. The
default value is No.
A1 08:=Yes
r
Sgl Key Quickarm
A1 11:=No
r
StayInstantScr
A1 12:=Yes
Night Scroll
r
A1 13:=No
r
NightInstantScr
A1 14:=No
r
StayChgIfArmed
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
A1 15:AreaNamel
Area 1
To program the text description of the Area (Name) press the left arrow key. Enter text
using the number keys. I.E. For a “K” press the 5 key twice. To move the cursor press
the right or left arrow keys. While programming the text, pressing the Chime key inserts
a space, and the Bypass key erases 1 digit. The up and down arrow keys toggle between
upper and lower case. Press the ELK key when complete.
VACATION MODE: During the exit delay time the Away key may be pressed to convert from Away mode to Away
Vacation mode. The Away Vacation mode does not alter any of the security arming times or zones. Its primary purpose
is for use with the Whenever/And/Then Rules programming of Elk-RP for enhanced energy savings modes.
AUTO ARMING: The control has an Auto Arming feature which may be setup using the “Whenever/And/Then Rules” in
the ELK-RP PC Programming Software. Basically, a rule must be written to initiate the auto arm sequence at a specific
time and/or date occurrence along with a programmable pre-warning time period. At the end of the pre-warn time, the
system will automatically arm to the AWAY mode, bypassing any violated Burglar zones. All area keypad(s) will beep
and display a warning when the initiating time occurs. Pressing the * key clears this warning for 1 minute. The auto arm
time may be extended in 10 minute increments by pressing the RIGHT arrow key. No further warnings will occur until 10
minutes prior to the newly “extended” auto arm time. Example 1: If a scheduled AutoArm is set for 06:00pm with a prewarn time of 20 minutes, the warning will start at 6:00pm and the auto arm will occur at 6:20pm. Pressing the RIGHT
arrow key to extend the time will cause the new auto arm time to be 6:30pm.
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 25
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
04-Keypad
Definitions
r
Menu 04 - Keypad Definitions
Press RIGHT arrow key to select this menu. Press UP or DOWN arrow keys to select
another menu. The ELK key backs up one menu level. To exit press the * or Exit key.
Keypad Definitions
Description of Option
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Up to 16 Keypads may be connected. Keypad 1 is the first to display. Press the right
arrow key to program, or press the up or down arrow keys to select another keypad. To
jump to any keypad enter the number (1-16). The keypad name displays on the bottom.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
A keypad can only be assigned as primary for a single area. However, it is possible to
“Map” a keypad to another area. Refer to Keypad Menus for instructions. Select which
“primary” area (1 to 8) that the keypad should be assigned. The default value is 1.
KP01: Selb
Keypad 1
Prgr
KP01 01:=1
r
Area Assigned To
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
KP01 02:=No
r
Silent on Entry
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
KP01 03:=No
Silent on Exit
r
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
KP01 04:=No
r
Silent on Chime
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
KP01 05:=No
r
Go dark in 60sec
If Yes, the keypad will not produce an entry warning signal during entry delay time after
violation of a delay 1 or delay 2 zone while armed. The default value is No.
If Yes, the keypad will not produce an exit warning tone during exit delay 1 or exit delay 2
times upon arming. The default value is No.
If Yes, the keypad will not produce any Chime tone even though the Chime mode may be
on and a chime type zone is violated. This is good for a baby’s room, etc. The default
value is No.
If Yes, the keypad will turn off all backlighting, including Armed or Ready lights, 60 secs.
after arming OR no pushbutton activity. This helps prevent unauthorized viewing of arm/
disarm status through a front glass window or door. Any button press resumes the status
display. The default value is No. NOTE: If any of the F Keys are being used as event
indicators this will also darken them, basically making them non-usable.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
KP01 06:=Yes
r
Show Date & Time
If Yes, the keypad will display the date and time on the bottom line of the LCD screen. If
there is too much information to display at once, the bottom line of the LCD will alternate.
The default value is Yes.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
KP01 07:=Yes
r
Show Temperature
If Yes, the keypad will display it’s local temperature on the bottom line of the LCD screen.
If there is too much information to display at once, the bottom line of the LCD will
alternate. The default value is Yes.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
If Yes, the keypad will display the name of the area in which it belongs. If there is too
much information to display at once, the bottom line of the LCD will alternate. The default
value is Yes.
KP01 08:=Yes
r
Show Area Name
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
KP01 09:=No
r
Byp Key Req PIN
If Yes, the Bypass key cannot be used unless a valid user code is entered. The default
value is No.
Keypad F1, F2, F3, F4, F5, F6 keys Each keypad has 6 lighted function keys that may be programmed to activate
specific operations. There are 7 programming attributes for each key: 1) KeyEvent - A four digit event code for the zone
definitions 0001 thru 0035, or the automation tasks 2001 - 2032. 2) KeyLight - A four digit event code which lights the
key when the event is active. This can be any of the Appendix A Event Codes. 3) Light Invert - A Yes/No option which
allows the light to be opposite of the event, off when active, on when not. 4) Light Blink - A Yes/No option which allows
the light to blink when active. 5) Key Requires PIN - A Yes/No option used to prevent the key from activating unless a
valid user code is entered. 6) Single Key Press - A Yes/No option which allows a single press of the key instead of the
normal double press to activate the event. NOTE: In the double press mode the key’s name is displayed on the LCD
screen as soon as the first press occurs. This serves to visually verify to the user that the correct key has been
selected prior to the second “activating” key press. 7) Key Name - A sixteen character programmable description that
describes the key’s function. I.E. Police Alarm, Garage Door, etc.
Page 26
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
Menu 04 - Keypad Definitions (continued)
Keypad Definitions
Description of Option
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
To program the F1 key definitions press the right arrow key. The program will branch off
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
into the 7 options for this key. To select another option press the UP or DOWN arrow
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
keys. To jump to a specific option enter the two digit number for that option.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
Key Event refers to what the key activates. F Keys can used to activate an Alarm, an
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
Automation Task, or by Elk-RP Whenever/And/Then Rules to activate most anything.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
Press the RIGHT arrow key and enter 4 digits. Enter 0000 if Elk-RP is going to be
12345678901234567890123456789012123
KP01 10:F1 Key r
Definitions
F1KeyEvent=0010r
Evt=Fire Alarm
used exclusively. Enter 0001-0036 for an alarm activation (see zone Defs), or 20012032 for an automation task activation (see Elk-RP software). The event description
is displayed along the bottom. Press the RIGHT arrow key to move to the next option.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
F1KeyLight=1001r
Evt=Fire Alarm
Key Light selects the event which will cause the key to light up. See Event Codes in
Appendix A. Press the RIGHT arrow key and enter 4 digits. The bottom line displays
the description of the event. Press the RIGHT arrow key to move to the next option.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Light Invert selects whether the key should be lighted when the event is On (normal) or
when the event is Off (Inverted). Press the RIGHT arrow key and select 1 for Yes or 0
for No. Press the RIGHT arrow key to move to the next option.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
Light Blink selects whether the key should blink when lighted or be steady. Press the
RIGHT arrow key and select 1 for Yes or 0 for No. Press the RIGHT arrow key to
move to the next option.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
F1 Key:=No
r
Key Requires PIN
Key Requires PIN selects whether the F key requires a valid user code prior to
activation. Press the RIGHT arrow and select 1 for Yes or 0 for No. Press the RIGHT
arrow key to move to the next option.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
If this option is No, a single press of the F key will activate the event. If Yes, then two
presses OR single press and hold 2 seconds is required. Press the RIGHT arrow and
select 1 for Yes or 0 for No. Press the RIGHT arrow key to move to the next option.
F1 Key:=No
Light Invert
F1 Key:=No
Light Blink
r
r
F1 Key:=No
r
SingleKeyPress
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
F1 Key Name
F1 = Fire
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
lr
The Key Name will be displayed whenever the F key is pressed. Press the LEFT
arrow key and enter text using the number keys. I.E. For “K” press the 5 key twice.
Move the cursor using the right or left arrow keys. The up or down arrow keys select
between lower and upper case. Press the ELK key when complete.
KP01 11:F2 Key r
Definitions
If the F2 Key is to be used, repeat the steps above.
KP01 12:F3 Key r
Definitions
If the F3 Key is to be used, repeat the steps above.
KP01 13:F4 Key r
Definitions
KP01 14:F5 Key r
Definitions
KP01 15:F6 Key r
Definitions
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
KP01 16:KP Namel
Keypad 1
If the F4 Key is to be used, repeat the steps above.
If the F5 Key is to be used, repeat the steps above.
If the F6 Key is to be used, repeat the steps above.
To edit the Keypad Name press the LEFT arrow key. Enter text using the number keys.
I.E. For “K” press the 5 key twice. Use the RIGHT or LEFT arrow keys to move the
cursor. The UP or DOWN keys select between lower and upper case. The Chime key
inserts a space, and the Bypass key erases 1 digit. Press the ELK key when complete.
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 27
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
05-Zone
Definitions
r
Zone Definitions
Menu 05 - Zone Definitions
Press RIGHT arrow key to select this menu. Press UP or DOWN arrow keys to select
another menu. The ELK key backs up one menu level. To exit press the * or Exit key.
Description of Option
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
ZN001: Selb Prgr
Zone 001
There is a maximum of 200 zones, numbered 1 to 8, and 17 to 208. Press the UP or
DOWN arrow key to scroll to a particular zone. To jump to a zone, enter the number from
001 to 208. The zone name displays along the bottom. Press the right arrow to program.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
This first option is used to set the zone definition. To locate a different option press the up
or down arrow key OR enter an option’s number to jump directly to it. Press the right
arrow key to program the selected option. The available definitions are:
ZN001 01:Def=01 r
Burg Entry/Exit1
Def Zone Description
Operating Characteristics
00
01
02
03
Disabled - Used to remove any unused zone(s). No need to put a jumper or resistor across the terminals.
Burglar Entry/Exit 1 - For perimeter entry/exit doors. Allows a time delay to enter and exit during arm and disarm.
Burglar Entry/Exit 2 - For perimeter entry/exit doors that require more time delay during arm and disarm.
Burglar Perimeter Instant - Windows and perimeter openings. Activates an immediate Burglary alarm if tripped
during ANY armed mode. Does not provide any exit or entry delay.
04 Burglar Interior - For motion detectors, interior doors, etc. Creates an instant alarm if tripped during the AWAY arm
mode. This zone type IS NOT ACTIVE during the STAY, STAY INSTANT, NITE, and NITE INSTANT arm modes.
05 Burglar Interior Follower - For motions detectors, interior doors, etc. which may be in the keypad or entry pathway.
If an entry delay zone is violated first, this zone will delay (Follow) also, otherwise it will create an instant alarm.
This zone type IS NOT ACTIVE during the STAY, STAY INSTANT, NITE, and NITE INSTANT arm modes.
06 Burglar Interior Nite - For motion detectors, interior doors, etc. which are not close to sleeping areas. The primary
use of this zone type is for increased security when the user is home. Interior Nite zones ARE ACTIVE during the
NITE and NITE INSTANT arm modes as well as the AWAY arm mode and will create an instant alarm if tripped.
This zone type is NOT ACTIVE during the STAY or STAY INSTANT arm modes.
07 Burglar Interior Nite Delay - For motion detectors, interior doors, etc. that are not close to sleeping areas. Same
as an Interior Nite zone except that Interior Nite Delay zones will delay for the entry/exit delay 1 time period. Interior
Nite zones ARE ACTIVE during the NITE and NITE INSTANT arm modes providing increased security when the
user is home and in bed. However, if the user accidentally wanders into a Nite Delay zone the entry delay timer
will start and the tone will sound, warning the user to disarm before a false alarm occurs.
NOTE: If “Auto Stay,No Exit” is set to YES (see Area Definitions) and the system is armed in the Away
mode, all interior zones will be bypassed if no exit is detected from the premises during the exit delay time.
Away Stay Stay Instant Nite
Nite Instant
Burg Entry/Exit (1 or 2) Zone
A
A
AN
A
AN
QUICK VIEW OF ARMING MODES
Burg Perimeter (Instant) Zone
AN
AN
AN
AN
AN
This illustrates the condition of Burg
Burglar Burg Interior Zone
AN
zone types in the various arm modes.
Burg Interior Follower Zone
A
Legend: A = Armed
Burg Interior Nite Zone
AN
AN
AN
“-” = Not Armed,
Burg Interior Nite Delay Zone
AN
A
AN
AN = Armed, No Delay
08
09
10
11
12
13
14
Page 28
Burglar 24 hr - Intended for tamper switches, etc. Activates an immediate Burglary alarm if tripped anytime
(during armed or disarmed state).
Burglar 24 hr Box Tamper - Intended for control, siren, and bell box tamper switches. Activates an immediate
Burglary Tamper alarm if tripped anytime (armed or disarmed state).
Fire 24 hr Alarm - Intended for Fire alarm sensors such as smoke detectors, heat stats, pull stations, etc.
Activates an immediate Fire alarm upon a short across the zone wires. A Fire Trouble will be activated if an open
(break in the zone wires) should occur.
Fire 24 hr ‘Verified’ - For smoke detectors in high-risk false alarm areas. Upon initial activation (short across the
zone), the control ignores the alarm and removes smoke power for 5 seconds to reset the detectors. During this 5
seconds, and for 25 additional seconds afterwards, no alarms will be recognized from this zone. Following this is
a 30 second verification time window, during which any additional activation will be regarded as verification of the
initial alarm and the control will initiate a Fire Alarm. If the 30 seconds expires with no further activations, the entire
process is cleared (reset). A Fire Trouble will be activated if an open (break in the zone wires) occurs.
Fire 24 hr Supervisory - Intended for monitoring water control valves on fire sprinkler systems. Same as Fire 24hr
except that a short across the zone activates a Fire Supervisory alarm. A Fire Trouble will be activated if an open
(break in the zone wires) should occur.
Auxiliary1 24 hr - This zone can trip anytime (armed or disarmed) and send a communicator report, but there is
no audible alarm output or keypad indication provided. It is displayed in the event log. A Whenever/And/Then rule
can be written from the RP software to do other things with this zone type. Resets upon restoral.
Auxiliary2 24 hr - This zone can trip anytime (armed or disarmed) and send a communicator report, but there is
no audible alarm output or keypad indication provided. It is displayed in the event log. A Whenever/And/Then rule
can be written from the RP software to do other things with this zone type. Resets upon restoral.
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
Menu 05 - Zone Definitions (continued)
Def Zone Description
Operating Characteristics
15 Keyfob - Used when a wireless keyfob is enrolled into a receiver at this zone ID location.
16 No Alarm - Intended for use in Whenever/And/Then rules from the Remote Programming RP software. This zone
type DOES NOT ACTIVATE any alarm and is not logged in the Event log. No reset is required.
17 Carbon Monoxide 24 hr - Activates an immediate Carbon Monoxide alarm if tripped anytime (armed or disarmed).
The keypad will display the alarm as well as the event log. This type of alarm can be silenced/reset with a valid
User Code. The audible alarm can be set in “Cutoff Timers”.
18 Emergency 24 hr - Similar to Def 17, this zone creates an alarm if tripped anytime (armed or disarmed).
19 Freeze Alarm 24 hr - Similar to Def 17, this zone creates an alarm if tripped anytime (armed or disarmed).
20 Gas Alarm 24 hr - Similar to Def 17, this zone creates an alarm if tripped anytime (armed or disarmed).
21 Heat Alarm 24 hr - Similar to Def 17, this zone creates an alarm if tripped anytime (armed or disarmed).
22 Medical Alarm 24 hr - Activates an immediate Medical alarm if tripped anytime (armed or disarmed).
23 Police Alarm w/Indication 24 hr - Activates an audible Police (Holdup) alarm if tripped (armed or disarmed).
24 Police Alarm no Indication 24 hr - Activates an non-audible Police (Silent) alarm if tripped (armed or disarmed).
25 Water Alarm 24 hr - Activates an immediate Water alarm if tripped anytime (armed or disarmed).
26 Keyswitch Momentary - Intended for a spring loaded momentary key switch. Toggles the armed state (disarmed/
armed) with each trip.
27 Keyswitch Momentary - Away Mode - Intended for a spring loaded momentary key switch. Arms the area in the
AWAY mode with each trip.
28 Keyswitch Momentary - Stay Mode - Intended for a spring loaded momentary key switch. Arms the area in the
STAY mode with each trip.
29 Keyswitch Momentary - Disarm Only - For a spring loaded momentary key switch. Disarms with each trip.
30 Keyswitch On/Off (Maintained) - Intended for a 2 position On/Off key switch. Arms the area in Open position.
Disarms the area in the Closed position.
31 Mute All Area Audibles - For silencing all area audibles by a two-way listen-in module (other manufacturer).
32 Power Supervisory 24 hr - For supervising an external power supply which provides alarm/trouble contacts. Wire
the power supply contacts to short the zone in a Low Battery event and open the zone in an AC Failure event.
33 Temperature - For use with ELK-M1ZTS Temperature Sensors. Requires the use of Whenever/And/Then rules
from the ELK-RP software. NOTE: This definition is for ZONES 1 thru 8 ONLY! Temperature zones must be set to
FAST LOOP (less that 200ms) response.
34 Analog - For sensors that produce a variable voltage (0 to 12 volt range). Requires the Whenever/And/Then rules
from the ELK-RP software.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
ZN001 02:Type=0r
0=EOL Supervised
Type
0
1
2
3
4
5
6
Refers to the wiring configuration for zones. Burglar and Keyswitch zones may be set to:
0, 1, 2, 3, & 4. Other non-fire zones may be set to: 0, 1 or 2 only. Fire zones may be
5=EOL Supervised 4-wire detectors, 6=EOL Supervised 2-wire detectors (zone 8 ONLY!)
Wiring Configuration
Operating Description
EOL Supervised, 2,200 Ohm resistor (Zones 1 - 8 are defaulted to Type=0)
Normally Closed only. No resistor required.
Normally Open only. No resistor required.
EOL Supervised with SECURITY ALERT on Short. (Burglar & Keyswitch Zones Only) When control is disarmed a
Security “Day” Alert will occur if the zone wiring is SHORTED. Keypads will beep and display the alert and zone
name. Press Star key to silence. User code must be entered to reset/acknowledge the alert. When control is
armed an alarm will occur regardless of whether the zone wiring is OPENED or SHORTED.
EOL Supervised - 4 State Wiring, with SECURITY ALERT on Open or Short. (Burglar & Keyswitch Zones Only)
Effective with firmware 4.3.5 this type provides 4 State Zone Wiring option, which uses 2 series EOL resistors, 1 in
series with the loop and 1 in parallel with the alarm contacts. When control is disarmed a Security “Day” Alert will
occur if the zone wiring is OPENED (tamper switch) or SHORTED. Keypad(s) will beep and display the alert and
zone name. Ideal for tampering motions, etc. Press Star key to silence. User code must be entered to reset/
acknowledge the alert. When control is armed an alarm will occur regardless of whether the zone is OPENED or
SHORTED.
NOTE: To define additional output/options on types 3 & 4 use the ElkRP Whenever/Then rules.
Fire, 4-Wire Smoke Detector with 2,200 Ohm EOL resistor. Trouble on open, alarm on short. (Zones 1 to 8).
Fire, 2-wire Smoke Detector with 680 Ohm EOL resistor. (ZONE 8 ONLY)
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
ZN001 03:Area=1 r
[Area Name]
ZN001 04: =No
Silent Alarm
r
Enter the area (partition) number that this zone is to be assigned to. A zone can only
reside in one area and fire zones can only reside in Area 1.
A zone programmed ‘Yes’ for Silent Alarm will not cause any audible alarm event from a
programmable output OR from any keypad. However, a visual display will occur on the
keypad(s) which are assigned to the same area as the zone.
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 29
Menu 05 - Zone Definitions (continued)
Zone Definitions
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
ZN001 05: =Yes
Dialer Delay
r
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
ZN001 06: =No
r
Enable Listen-In
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
ZN001 07: =No
r
Zone Bypassable
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
ZN001 08: =No
Force Armable
r
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
ZN001 09: =No
r
SwingerShutdown
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
ZN001 10: =No
r
Req PeriodicTrip
Description of Option
Dialer delay is designed to reduce false alarm dispatches. Upon an alarm from a zone
with this option the communicator delays dialing for the “Dialer Delay” time programmed in
Menu 09-Area Reporting Codes. If a valid code is entered before this delay expires, the
report will ABORT (no report). If an ‘Alarm Abort” code is programmed, (see Menu 09), the
communicator will transmit this in place of the alarm. NOTE: The Dialer Delay Time will
only start once per alarm, regardless of additional zone trips. Default setting is No.
Allows zone to trigger a listen-in session after alarm is reported. Control will hold the line
for 60 seconds after ‘kiss-off’, allowing Central Station to enter *55* to activate listen-in.
The Central Station can renew or terminate listen-in remotely. NOTE: Two-Way must be
enabled (Menu 07-Globals) and an interface (ELK-M1TWI) with one or more microphone/
speakers (ELK-M1TWS) must be installed. Default setting is No.
A Yes allows zone to be manually bypassed. A bypassed zone will be ignored by the
system. Burglar zone bypasses are canceled upon a disarm. To bypass a zone: Press
the Bypass key + [zone number] + the Bypass key once again. Default setting is Yes.
Force Arm allows a violated zone to be temporarily bypassed upon arming. Prior to arm,
the READY light blinks if force arm zone(s) are the only zones violated. Force arm
requires two entries of a user code. Quick arm cannot be used for force arming. Upon
the first code entry the keypad will display READY FORCE. The second code entry will
force arm. Force armed zone(s) automatically return to service if they become normal
while armed. CAUTION! Force arm operates in a unique way on entry/exit zones! Entry/Exit zones that are also force armable can be violated during the exit delay and still
become force armed. This allows a user to arm, open a garage door, back out, and then
shut the door at their leisure, without creating a false alarm and without a long exit delay
time. As soon as the garage door is closed, it will automatically return to service. Default
setting is No. NOTE: For UL installations Force Arm shall be disabled.
Swinger Shutdown prevents a runaway communicator by shunting a zone after two trips.
It cannot send another alarm until the control is reset OR a 48 hour time period elapse.
Default setting is No. NOTE: For UL installations this feature shall be disabled.
This type zone must be tripped at least once per disarm cycle*. This prevents blocked
PIRs or seldom used doors from being left not secure. Keypad will display “Not Ready” if
a periodic zone has not been tripped. * NOTE: A periodic trip will not be required for a
disarm period of 1 hour or less. Default setting is No.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Response is the time the zone must be violated before the system detects it. If No, the
zone responds to the Slow response time. The time values are in milliseconds and they
are programmed in the Menu 07 Global Sys. Definitions menu. Default setting is No.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Each zone may be selected to be included in the Chime annunciation whenever Chime
Mode is turned on from the keypad. Most zone types may be included via this option.
Default setting is No.
ZN001 11: =No
r
FastLoopResponse
ZN001 12: =No
Enable Chime
r
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
ZN001 13: =No
r
In CrossZonePool
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
ZN001 14:Namel
Zone 001
Page 30
Burglar zones programmed “In CrossZonePool” cannot cause an alarm unless another
zone in the cross zone pool also activates within a time window OR unless “Cross Zone
Self Ver“ is Menu 07 - Global System Definitions. Entry/exit zones should NOT be
programmed as Cross zones. Default setting is No.
To program the text description of the Zone (Name) press the left arrow key. Enter text
using the number keys. I.E. For a “K” press the 5 key twice. To move the cursor press
the right or left arrow keys. While programming the text, pressing the Chime key inserts
a space and the Bypass key erases 1 digit. The up and down arrow keys move between
upper and lower case. Press the ELK key when complete.
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
06-Alarm Cutoff
Timers
r
Menu 06 - Alarm Duration Timers
Press RIGHT arrow key to select this menu. Press UP or DOWN arrow keys to select
another menu. The ELK key backs up one menu level. To exit press the * or Exit key.
Each alarm type has a duration timer for cutting off the alarm after a programmable time period. Any output assigned to
the alarm type will turn on when the alarm activates and will turn off when the alarm cutoff timer expires. If multiple alarm
types are assigned to a single output, all alarms must turn off before the output can turn off. The range in seconds is
00000 to 65535. 00000=Never turn on. 65535=Never turn off NOTE: 65535 seconds is 1,092 minutes or 18.2 hours.
Alarm Cutoff Timers
Description of Option
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
Burglar Alarm duration time in seconds. Default time is 00600 sec. (10 min.). Burglar
always activates Siren/Voice Output (Out1) and Siren Output (Out2). Additional outputs
may be programmed using the RP software “Rules” function.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
Fire Alarm duration time in seconds. Default time is 65535 sec. (never cutoff). Fire always
activates Siren/Voice Output (Out1) and Siren Output (Out2). Additional outputs may be
programmed using the RP software “Rules” function.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
Medical Alarm duration time in seconds. Default time is 00600 sec. (10 min.). Medical
always activates Siren/Voice Output (Out1) and Siren Output (Out2). Additional outputs
may be programmed using the RP software “Rules” function.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
Audible Police Alarm duration time in seconds. Default time is 00600 sec. (10 min).
Audible Police always activates Siren/Voice Output (Out1) and Siren Output (Out2).
Additional outputs may be programmed using the RP software “Rules” function.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
CT05:=00600 secr
CO Duration
CO (Carbon Monoxide) Alarm duration time in seconds. The default time is 00600 sec. (10
min.). This alarm type is not preassigned to any outputs. The RP software “Rules”
function must be used to assign outputs.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
Emergency Alarm duration time in seconds. The default time is 00600 sec. (10 min.).
This alarm type is not preassigned to any outputs. The RP software “Rules” function must
be used to assign outputs.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
Freeze Alarm duration time in seconds. The default time is 00600 sec. (10 min.). This
alarm type is not preassigned to any outputs. The RP software “Rules” function must be
used to assign outputs.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
Gas Alarm duration time in seconds. The default time is 00600 sec. (10 min.). This alarm
type is not preassigned to any outputs. The RP software “Rules” function must be used
to assign outputs.
CT01:=00600 secr
BurgDuration
CT02:=00000 secr
FireDuration
CT03:=00600 secr
Med Duration
CT04:=00600 secr
Pol Duration
CT06:=00600 secr
EmerDuration
CT07:=00600 secr
FrezDuration
CT08:=00600 secr
Gas Duration
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
CT09:=00600 secr
HeatDuration
Heat Alarm duration time in seconds. The default time is 00600 sec. (10 min.). This alarm
type is not preassigned to any outputs. The RP software “Rules” function must be used
to assign outputs.
CT10:=00600 secr
WatrDuration
Water Alarm duration time in seconds. The default time is 00600 sec. (10 min.). This
alarm type is not preassigned to any outputs. The RP software “Rules” function must be
used to assign outputs.
CT11:=00600 secr
Aux1Duration
Aux 1 Alarm duration time in seconds. The default time is 00600 sec. (10 min.). This
alarm type is not preassigned to any outputs. The RP software “Rules” function must be
used to assign outputs.
CT12:=00600 secr
Aux2Duration
Aux 2 Alarm duration time in seconds. The default time is 00600 sec. (10 min.). This
alarm type is not preassigned to any outputs. The RP software “Rules” function must be
used to assign outputs.
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 31
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
07-Global System r
Definitions
Global Sys Definitions
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
G02: =Yes
12Hr Time Disp
r
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
G03: =No
r
DD/MM Date Disp
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
04: =No
r
Celcius TempDisp
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
G05: =Yes
r
Daylight Savings
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
G06: =0040 ms r
Fast Loop Resp
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
G07: =0400 ms r
Slow Loop Resp
Menu 07 - Global System Definitions
Press RIGHT arrow key to select this menu. Press UP or DOWN arrow keys to select
another menu. The ELK key backs up one menu level. To exit press the * or Exit key.
Description of Option
Keypads that are programmed to show time and date on their second display line will
either display 12 hour format or 24 hour military format, depending upon this option.
Default is Yes
If this option is No, the date will display as Month/Day/Year. If this option is Yes, the date
will display as Day/Month/Year. Default No.
Keypads that are programmed to show temperature on their second display line will either
display as Celsius or Fahrenheit, depending upon this option. Default is No.
The system will automatically adjust its internal clock for daylight savings time changes if
this option is set to ‘Yes’. Default is Yes.
Sets the time that a “Fast Loop” zone must remain open before the control responds. To
set, press the RIGHT arrow key and enter a number from 002 to 255. Time is adjusted in
10 millisecond increments from 20ms to 2550ms (2.55 seconds). Default is 40ms.
Sets the time that a “Slow Loop” zone must remain open before the control responds. A
“Slow Loop” zone is basically any zone that does not have the “FastLoopResponse”
option enabled in Menu 05 - Zone Definitions. To set, press the RIGHT arrow key and
enter a number from 002 to 255. Time is adjusted in 10 millisecond increments from
20ms to 2550ms (2.55 seconds). Default is 400ms.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Zones programmed with the ‘Cross Zone’ option may be allowed to self-verify an alarm
condition. I.E. A second trip of the same zone within the Cross Zone Verify Time window
will be considered a verified alarm. Default is No.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
This timer function is the amount of time in seconds that is allowed for two or more ‘Cross
Zone” zones to verify each other in an alarm condition OR for a second trip of the same
zone when ‘CrossZoneSelfVer’ has been enabled. Default is No.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
This option selects whether ordinary non-fire system troubles will cause audible alerts to
sound. This option does not affect fire trouble conditions, which will always be audible.
Default is No.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
The Control supports up to 99 User codes, plus the Installer code. The User codes can
be either 4 digits in length or 6 digits, depending upon this option. Default is No (4 digits).
NOTE: The Installer code is ALWAYS 6 digits.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
To prevent a would be thief or hacker from being able to hunt for a valid user code, the
system can automatically lock out all code entry for 1 minute after a sequence of invalid
digits. The range of value can be set from 13 to 99. Default is 99.
G08: =No
r
CrossZoneSelfVer
G09: =030
r
CrossZoneVerTime
G10: =Yes
r
Audible Troubles
G11: =No
r
6 Digit UserCode
G12:=99 Digits r
WrongCodeLockout
Page 32
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
Menu 07 - Global System Definitions (continued)
Global Sys Definitions
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
G13:_ _ _ _ _ _ _ _r
Common To Area1
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
G14:=No Out2r
Chg YelpToBuzzer
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
G26: =No
r
Out2 Voltage Out
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
G27:=000secOut2r
Delay Turn-On
Description of Option
Any of the Areas 2 thru 8 may be made common to Area 1. The result is: Area 1 cannot
be armed until all its common areas are armed. Once armed, Area 1 will disarm if any
common area becomes disarmed. This is good for lobbies or vestibules shared by two or
more businesses. Each business must have their own area keypad. NOTE: If you want
Area 1 to automatically arm when all its common areas become armed, use a
Whenever/And/Then rule from the RP software to do this.
Changes the Burglar Yelp sound on outputs 2 to a pulsing Buzzer sound. Default is No.
NOTE: When connecting 8 Ohm speakers, do not exceed an 4 Ohm total load.
Options G15 thru G25 are not used.
Allows Output 2 to be converted from a siren driver into a voltage only output. If set to
“No” the control produces alarm sounds for use with 8 Ohm speakers. If set to “Yes” the
control will produce +12 Volts for use with self-contained sirens or bells. Default is No.
Ordinarily, Outputs 1 & 2 activate immediately on alarms. However, Output 2 can be time
delayed up to 255 seconds. Using Output 1 strictly for interior sounders and Output 2 for
outside sounders, a false alarm will be heard inside first, giving the user time to disarm
before any outside sounders are activated. A “good neighbor” feature. Default is 000.
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 33
Menu 07 - Global System Definitions (continued)
Global Sys Definitions
Description of Option
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
G28:=No Out2 r
SingleAlmLockout
Output 2 can be set to alarm only once per armed cycle for burglary type alarms. This
feature is intended for noise abatement. The dialer will continue to transmit all alarms that
may occur. THIS ONLY LOCKS OUT AUDIBLE FROM OUTPUT 2.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
The control must be set to auto answer an incoming call in order for Remote Programming
(RP) to be accessed remotely. The range of rings can be set from 1 to 15. A value of “0”
disables auto answer.
G29:=00 Rings r
Until AutoAnswer
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
G30:=No
r
Ring/Hang/Answer
A Yes enables faster connection from an outside telephone. It works as follows: Call the
control and hang up after 1 or 2 rings. This starts a 45 second timer. Call the control a
2nd time during this 45 second time and the control will answer on the first ring. In some
cases this Ring/Hang/Answer option may be the only way to get around telephone
company provided answering services. Option 29 MUST also be set!
NOTE: If an on-site answering machine picks up, the RP software and the control
will automatically attempt to override the machine using tone sniffing methods.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
G31:=No
2Wayr
Listen-In Enable
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Set this option to Yes ONLY when an ELK-M1TWI Two Way Listen-In interface is
installed. This enables the correct software commands and procedures to make the two
way functional. Refer also to the instructions that are shipped with the ELK-M1TWI
G32:=00sec 2Wayr
CallbackTime
If Two Way is enabled, this timer provides a window for the CS to enter * 55 * and activate
two way listen-in by holding the phone line off-hook for 001 to 255 seconds after a kissoff.
Upon hangup, this timer re-starts to provide a window for the CS to callback and initiate
two way. Control will answer an incoming call on the first ring. Enter 000 to disable.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Allows the Central Station alarm verification by suspending (holding) new alarms after the
initial alarm kissoff. The phone line is kept free for this time period. The time value can be
from 001 to 255 seconds. Long time periods are not recommended. Enter 000 to disable.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
This location is used to select the initial (default) baud rate for the on-board RS-232 serial
port which is Port 0. The available baud rates are: 0 or 1=300 baud, 2=1200, 3=2400,
4=4800, 5=9600, 6=14400, 7=19200, 8=38400, and 9=115200
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
The control can transmit ASCII data via it’s RS-232 port to automation types of equipment.
The ELK ASCII Protocol document is available upon request. This first option sets the
control to transmit all event log information immediately as it occurs.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
This option sets the control to transmit zone status changes immediately as they occur.
The ELK ASCII Protocol document is available upon request.
G33:=000sec CSr
Verify Call Time
G34:=9 115200r
Baud Rate Port 0
G35:=No Xmitr
Event Log- ASCII
G36:=No Xmitr
Zone Chgs - ASCII
G37:=No Xmitr
OutputChgs-ASCII
Page 34
This option sets the control to transmit output status changes immediately as they occur.
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
Menu 07 - Global System Definitions (continued)
Global Sys Def
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
G38:=No Xmitr
Task Chgs - ASCII
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
G39:=No Xmitr
Light Chgs-ASCII
Description of Option
This option sets the control to transmit automation task status changes immediately as
they occur.
This option sets the control to transmit automation lighting status changes immediately
as they occur.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
G40:=No Xmitr
Keypad Key Chgs
Sets the control to transmit keypad key changes. This includes the Chime, Bypass, Exit,
Stay keys, the ELK key and it’s surrounding arrow keys, and the F keys. It does not
transmit any of the numeric keys..
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
G41:=No Require
Code UserMenu1-5
Allows User Menus 1 through 5 to be blocked from view until a valid User code is entered.
If set to “Yes”, only User Codes which have the “Menu 1-5 Allowed” option enabled will be
able to view or access Menus 1 through 5. Default is No.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
This is the 6 digit Installer program code that is required in order to access the local
installer programming mode. NOTE: Be careful when changing this code as it will be
impossible to program the panel if the code is programmed wrong or forgotten.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
This is a read-only location. Each control is assigned a unique serial number for
identification of the unit regarding warranty, technical support, anti-takeover, and other
issues that may arise.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
This is a read-only location displaying information about the current software and
bootloader revision that the control is operating with. This will only be needed with the
assistance of a factory technical support person.
G42:=172839
r
Local Prog Code
G43:=D1234567
Serial Number
r
G44:xxxxxxxxxxxx
Axxxxxx Bxxxxxx
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
G45:=DefaultCtl r
81=User Codes
This option allows factory default values to be restored by individual menus/categories.
Press the right arrow to select this option, then press the up or down arrow keys to scroll
through the choices. To factory default any single category enter the displayed number.
For example, entering 81 from this screen will cause all the User Codes to be factory
defaulted. Please be patient as it may take a minute or more to default some items.
82=Areas Data
Entering 82 from this screen causes all area definitions to be factory defaulted.
83=Keypads Data
Entering 83 from this screen causes all keypad definitions to be factory defaulted.
84=Zones Data
Entering 84 from this screen causes all zone definitions to be factory defaulted.
85=Zone Names
Entering 85 from this screen causes all zone names to be factory defaulted.
86=CutoffTimes
Entering 86 from this screen causes all the cutoff timers to be factory defaulted.
87=Global Data
Entering 87 from this screen causes all global system defs to be factory defaulted.
88=TeleAcct Data
Entering 88 from this screen causes all telephone reporting setup to be factory defaulted.
89=Tele #’s Only
Entering 89 from this screen causes all telephone numbers ONLY to be factory defaulted.
90=AreaRptCodes
Entering 90 from this screen causes all area report codes to be factory defaulted.
91=ZoneRptCodes
Entering 91 from this screen causes all zone report codes to be factory defaulted.
92=SysRptCodes
Entering 92 from this screen causes all system report codes to be factory defaulted.
93=UserRptCodes
Entering 93 from this screen causes all user report codes to be factory defaulted.
95=WirelessDef
Entering 95 from this screen causes all wireless definitions to be factory defaulted.
99=Entire Panel
Entering 99 from this screen causes the entire panel programming to be factory defaulted.
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 35
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
08-Telephone
r
Account Setup
Telephone Acct Setup
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
T1: Selb
Prgr
[Name for Tel#1]
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
T1: 01:Format=0 r
0=Disabled
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
T1: 02: = 0
r
0=Always Report
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
T1: 03:Num=
Menu 08 - Telephone Account Setup
Press RIGHT arrow key to select this menu. Press UP or DOWN arrow keys to select
another menu. The ELK key backs up one menu level. To exit press the * or Exit key.
Description of Option
The control can dial up to 8 telephone numbers plus the ELK-RP number. Each of the 8
phone numbers can be used to report alarms, troubles, closings, opening, etc. in digital
format as well as pager formats. Use the up/down arrow keys to select the telephone
number, then press the right arrow key to program the options, starting with option 01.
This selects the reporting format to be used with this number. The available formats are:
00 = Disable reporting
03 = Pulse 4+2
06 = Ethernet
01 = Contact ID
04 = Pager DTMF tones
02 = SIA
05 = not used
0=Always Report, meaning the number will be dialed when its “report to” options are
activated. 1=Backup, meaning the number will ONLY be dialed if the previous sequential
number failed to complete its call. When backup is selected the “report to” options will be
copied from the previous number and ONLY the name, number, format, and dial attempts
may be edited. To edit any “report to” options you must temporarily set this value to 0.
NOTE: Telephone # 1 cannot be set as a backup since it is the first number. A
backup cannot have another backup.
Up to 20 digits may be entered for a telephone number. Valid numeric digits are: 1, 2, 3,
4, 5, 6, 7, 8, 9, and 0. In addition, the following special characters may be programmed.
The cursor automatically moves right each time a digit is entered.
Comma (,) = forces the dialer to pause for 2 seconds
Slash (/) = forces the dialer to pause for 125 milliseconds.
Asteric (*) = simulates the * key on a touch tone phone
Pound (#) = simulates the # key on a touch tone phone
B = Program the 1st dialed digit as a “B” to force Pulse (rotary) dialing. Anywhere else in the dial string a “B” will simply
be handled as a DTMF tone signal
C = Not Used
D = Program the 1st dialed digit as a “D” to force Dial tone detection prior to dialing. Otherwise, it dials regardless of
dial tone presence. Anywhere else in the dial string a “D” will simply be handled as a DTMF tone signal.
EXCEPTION: Digit D (Dial tone detect) can be the 2nd digit but ONLY if B (Pulse dial) is the 1st dialed digit.
To enter special characters place the cursor where desired and press the up arrow key. The 1 key will now
produce characters 1, #, *, and /. The 2 key will produce 2, A, B, and C. The 3 key will produce 3, and D. When
finished press the down arrow key to return to numbers.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
T1: 04: = 08
Dial Attempts
r
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
T1: 05:=000000r
Acct # for Area1
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
T1: 06:=000000r
Acct # for Area2
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
T1: 07:=000000r
Acct # for Area3
Page 36
This sets the number of dial attempts (re-dials) that the communicator will make to this
number before a Comm Fail (fail to report) is logged. Valid range is 01 to 15 attempts.
Default is 08.
The Account number for Area 1 (up to 6 digits) when it is reported to this telephone
number. Since all 6 digits must be entered, enter leading zeros (0’s) if a shorter account
number is required.
The Account number for Area 2 (up to 6 digits) when it is reported to this telephone
number. Since all 6 digits must be entered, enter leading zeros (0’s) if a shorter account
number is required.
The Account number for Area 3 (up to 6 digits) when it is reported to this telephone
number. Since all 6 digits must be entered, enter leading zeros (0’s) if a shorter account
number is required.
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
Menu 08 Telephone Account Setup (continued)
Telephone Acct Setup
Description of Option
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
T1: 08:=000000r
Acct # for Area4
The Account number for Area 4 (up to 6 digits) when it is reported to this telephone
number. Since all 6 digits must be entered, enter leading zeros (0’s) if a shorter account
number is required.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
T1: 09:=000000r
Acct # for Area5
The Account number for Area 5 (up to 6 digits) when it is reported to this telephone
number. Since all 6 digits must be entered, enter leading zeros (0’s) if a shorter account
number is required.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
T1: 10:=000000r
Acct # for Area6
The Account number for Area 6 (up to 6 digits) when it is reported to this telephone
number. Since all 6 digits must be entered, enter leading zeros (0’s) if a shorter account
number is required.
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
T1: 11:=000000r
Acct # for Area7
The Account number for Area 7 (up to 6 digits) when it is reported to this telephone
number. Since all 6 digits must be entered, enter leading zeros (0’s) if a shorter account
number is required
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
The Account number for Area 8 (up to 6 digits) when it is reported to this telephone
number. Since all 6 digits must be entered, enter leading zeros (0’s) if a shorter account
number is required.
T1: 12:=000000r
Acct # for Area8
THE FOLLOWING 5 OPTIONS DEFINE WHAT IS REPORTED BY THIS TELEPHONE #
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
T1: 13:=Yes Rptr
AreaAlms,RestUnbp
This YES or NO option identifies whether this telephone number should report misc.
options from the AREA REPORTING CODES menu, Zone Alarms, Restores, and
Unbypasses from the ZONE REPORTING CODES menu, and Keypad Alarms from the
KEYPAD F-KEY REPORTING CODES menu.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
This YES or NO option identifies whether this telephone number should report the Zone
Bypasses from the ZONE REPORTING CODES menu.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
This YES or NO option identifies whether this telephone number should report the Zone
Troubles from the ZONE REPORTING CODES menu.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
This YES or NO option identifies whether this telephone number should report the user
opening and closing codes from the USER REPORTING CODES menu.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
This YES or NO option identifies whether this telephone number should report the global
system event codes from SYS REPORT OPTIONS & CODES menu.
T1: 14:=No Rptr
Bypasses
T1: 15:=No Rptr
Zone Troubles
T1: 16:=No Rptr
User ReportCodes
T1: 17:=Yes Rptr
Global SysEvents
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
T1: 18:Name
l
[Name for Tel#1]
To edit or program a text description (Name) such as “ACME Central Station” for the
Telephone number press left arrow key. Spell out the text using the number keys. I.E.
For a “K” press the 5 key twice. To move the cursor press the right or left arrow keys.
While programming the text, pressing the Chime key inserts a space, and the Bypass
key erases 1 digit. The up and down arrow keys toggles between upper and lower case.
Press the ELK key when complete.
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 37
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
09-Area Reporting
Codes
r
Menu 09 - Area Reporting Codes
Press RIGHT arrow key to select this menu. Press UP or DOWN arrow keys to select
another menu. The ELK key backs up one menu level. To exit press the * or Exit key.
NOTE: Enter a two digit value to enable a particular report code. To disable a report code enter 00. When SIA or
Contact ID is the reporting format, the two digit value can simply be 01 since the control automatically produces the
correct code according to the SIA or Contact ID protocol. For 4+2 pulse format, enter a value from 01 to FF. To enter
the A thru F HEX characters press the RIGHT arrow key to position the cursor under the desired digit, then press the UP
arrow (shift) key once. Each press of the 2 key will now produce the following: 2, A, B, C. Each press of the 3 key will
now produce the following: 3, D, E, F. Press the RIGHT arrow key to cancel shift and move to the next character. See
Appendix for a summary of the SIA and Contact ID codes.
Area Report Codes
Description of Option
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Each of the eight (8) Areas has specific communicator reporting codes for events that only
occur within that area. Using the up/down arrow keys, select the appropriate area, then
press the right arrow key to begin starting with option 01.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Dialer Delay Time is an amount of time following an alarm during which the report may be
aborted if the area is disarmed by a valid user. An optional alarm abort code may be
programmed to report. Range is 000 to 255 seconds. Default is 000 (delay disabled).
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Alarm Abort code is an optional code that may be reported when an alarm is aborted
during the Comm Abort Time window. Range is 00 to FF. Default is 00 (no report).
.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Cancel Window Time is the time following an alarm during which a cancel code will be
reported if the area is disarmed. Cancel is not the same as abort since the alarm has
already reported. Range is 00 to FF. Default is 00 (no report).
AR1: Selb
Prgr
ReportCodesArea1
AR1 01:000=Sec r
Dialer Delay Time
AR1 02:Code= 00r
Alm Abort Code
AR1 03:000=Sec r
CancelWindowTime
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
AR1 04:Code= 00r
Alm Cancel Code
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Alarm Cancel code is the code that will be reported if the area in alarm is disarmed within
the Cancel Window Time. Range is 00 to FF. Default is 00 (no report).
AR1 05:Code= 00r
Close Automatic
Close Automatic code will be reported anytime the area is armed automatically by a Rule
from the RP software programming. Refer to the ELK-RP Rules Programming
instructions. Range is 00 to FF. Default is 00 (no report).
AR1 06:Code= 00r
Close Early
Close Early code will be reported if the area is closed prior to a programmed Expected
Arm time. Refer to the ELK-RP Rules Programming instructions. Range is 00 to FF.
Default is 00 (no report).
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Close Extended code will be reported if a programmed Expected Arm time is extended by
a valid user. Refer to the ELK-RP Rules Programming instructions. Range is 00 to FF.
Default is 00 (no report).
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Fail to Close code will be reported if the area is not armed by a programmed Expected
Arm time. Refer to the ELK-RP Rules Programming instructions. Range is 00 to FF.
Default is 00 (no report).
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
AR1 09:Code= 00r
Late Close
Late to Close code will be reported if the area is armed after a programmed Expected Arm
time. Refer to the ELK-RP Rules Programming instructions. Range is 00 to FF. Default
is 00 (no report).
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Keyswitch Close code will be reported in place of a user code whenever the area is armed
by a keyswitch. Refer to the ELK-RP Rules Programming instructions. Range is 00 to
FF. Default is 00 (no report).
AR1 07:Code= 00r
Close Extended
AR1 08:Code= 00r
Fail To Close
AR1 10:Code= 00r
Keyswitch Close
Page 38
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
Menu 09 - Area Reporting Codes (continued)
Area Report Codes
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
AR1 11:Code= 00r
Duress Code
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
AR1 12:Code= 00r
Open After Alrm
Description of Option
Duress code will be reported if the area is armed or disarmed by a valid user code that is
programmed with the duress attribute. Range is 00 to FF. Default is 00 (no report).
Open After Alarm code will be reported whenever a valid user arrives and disarms the area
following an alarm activation. Range is 00 to FF. Default is 00 (no report).
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
AR1 13:Code= 00r
Open Early
Open Early code will be reported if the area is disarmed prior to a programmed Expected
Disarm time. Refer to the ELK-RP Rules Programming instructions. Range is 00 to FF.
Default is 00 (no report).
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
AR1 14:Code= 00r
Fail To Open
Fail to Open code will be reported if the area is not disarmed by a programmed Expected
Disarm time. Refer to the ELK-RP Rules Programming instructions. Range is 00 to FF.
Default is 00 (no report).
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
Open Late code will be reported if the area is disarmed after a programmed Expected
Disarm time. Refer to the ELK-RP Rules Programming instructions. Range is 00 to FF.
Default is 00 (no report).
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
Open Keyswitch code will be reported in place of a user code whenever the area is
disarmed by a Keyswitch zone. Range is 00 to FF. Default is 00 (no report).
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
User Lockout code will be reported if someone repeatedly enters digits (see Menu 07 Global System Definitions, Option 12 for the maximum number of digits allowed) in an
attempt to hack out a valid user code. Range is 00 to FF. Default is 00 (no report).
AR1 15:Code= 00r
Open Late
AR1 16:Code= 00r
Open Keyswitch
AR1 17:Code= 00r
User Lockout
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
AR1 18:Code= 00r
Exit Error
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
AR1 19:Code= 00r
Fail Communicate
Exit Error Code can be used to identify an accidental alarm caused by an error while
arming. Locally, it works as follows: If an exit delay rolls directly into entry delay as a
result of a zone being left violated, the entry delay warning AND the siren will sound. If the
control is not disarmed prior to the entry delay expiring, the communicator will report the
alarm along with the Exit Error code. Range is 00 to FF. Default is 00 (no report).
Fail to communicate displays on the keypad and the event log when the communicator
fails to complete it’s report using the number of dial attempts. A good communications
report must occur in order to reset/clear the failure. If this fail to communicate report code
is enabled, it will be reported with next good communications to indicate a “past” failure.
Range is 00 to FF. Default is 00 (no report).
Based on the event, the CID (Contact ID) or SIA Codes for Area Reporting Codes will be:
Area RCs
Alarm Abort
Alarm Cancel
Automatic Close
Early Close
Closing Extended
Fail To Close
Late Close
Key Switch Close
Duress
CID
406
406
403
451
464
454
452
409
121
SIA
OC
OC
CA
CK
CE
CI
CJ
CS
HA
Area RCs
Open After Alarm
Early Open
Fail To Open
Late Open
Key Switch Open
Keypad Locked Out
Exit Error
Fail To Communicate
CID
450
451
453
452
409
461
457
354
SIA
OR
OK
OI
OJ
OS
JA
EE
RT
NOTE: On CID reporting the 3 digit code will be preceded by a “1” for a new event or
an opening. It will be preceded by a “3” for a restore or a closing event.
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 39
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
10-Zone Reportng
Codes
r
Menu 10 - Zone Reporting Codes
Press RIGHT arrow key to select this menu. Press UP or DOWN arrow keys to select
another menu. The ELK key backs up one menu level. To exit press the * or Exit key.
NOTE: Enter a two digit value to enable a report code. To disable a report code enter 00. When SIA or Contact ID is the
reporting format, the two digit value can simply be 01 since the control automatically produces the correct code
according to the SIA or Contact ID protocol. For 4+2 pulse format, enter a value from 01 to FF. To enter the A thru F
HEX characters press the RIGHT arrow key to position the cursor under the desired digit, then press the UP arrow (shift)
key once. Each press of the 2 key will now produce the following: 2, A, B, C. Each press of the 3 key will now produce
the following: 3, D, E, F. Press the RIGHT arrow key to cancel shift and move to the next character. See Appendix for
a summary of the SIA and Contact ID codes.
Zone Report Codes
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Z001: Selb Prgr
[Name of Zone]
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Z001:A=00 R=00 r
Byp=00 Tbl=00
Description of Option
Each of the 208 Zones has specific communicator reporting codes for Alarm, Restore,
Bypass, and Trouble. Using the up/down arrow keys, select the appropriate zone, then
press the right arrow key to begin programming of that zone.
The cursor starts at the 00 beside A (Alarm). Enter the desired two digit reporting code
and press the right arrow key to advance to the R (Restore). To jump the cursor to another
report without changing this one simply press the right arrow key. The next press of the
right arrow key after Tbl (Trouble) will advance the screen back to the beginning of that
zone. Range is 00 to FF. Default for all entries is 00 (no report).
NOTE: Each reporting code must be programmed according to the desired reporting
format. However, for SIA and Contact ID formats the actual reporting digits will be
produced by the control according to the type of alarm or event. The only programming
required to enable reporting with the SIA and Contact ID formats is to set the programmed
code to a non zero (0) value. See below:
Based on the zone definition, the CID (Contact ID) or SIA formats for Zone Reporting Codes will be:
Zone RCs
01 = Burglar Entry/Exit 1
02 = Burglar Entry/Exit 2
03 = Burglar Perim Inst
04 = Burglar Interior
05 = Burglar Int Follower
06 = Burglar Int Night
07 = Burglar Int Nt Fllwr
08 = Burglar 24 Hour
09 = Burglar Box Tamper
10 = Fire Alarm
11 = Fire Verified
12 = Fire Supervisory
13 = Aux Function 1
14 = Aux Function 2
15 = Keyfob
16 = Non Alarm
17 = Carbon Monoxide
Alarms
CID SIA
134 BA
134 BA
131 BA
132 BA
132 BA
135 BA
135 BA
133 BA
137 TA
110 FA
110 FA
200 FS
150 UA
150 UA
---- ------- ---162 GA
Restore
CID SIA
134 B R
134 B R
131 B R
132 B R
132 B R
135 B R
135 B R
133 B R
137 T R
110 F R
110 F R
200 F R
150 U R
150 U R
---- ------- ---162 GR
Bypass
CID SIA
573 BB
573 BB
573 BB
573 BB
573 BB
573 BB
573 BB
573 BB
573 TB
571 FB
571 FB
571 FB
572 UB
572 UB
---- ------- ---572 GB
Trouble
CID SIA
370 BT
370 BT
370 BT
370 BT
370 BT
370 BT
370 BT
370 BT
370 BT
373 FT
373 FT
373 FT
---- ------- ------- ------- ------- ----
Zone RCs
18 = Emergency Alarm
19 = Freeze Alarm
20 = Gas Alarm
21 = Heat Alarm
22 = Medical Alarm
23 = Police Alarm
24 = Police No Indication
25 = Water Alarm
26 = Key Mom Arm/Disarm
27 = Key Mom Arm Away
28 = Key Mom Arm Stay
29 = Key Mom Disarm
30 = Key On/Off
31 = Mute Audibles
32 = Power Supervisory
33 = Temperature
34 = Analog Zone
Alarms
CID SIA
101 QA
159 Z A
151 GA
114 KA
100 MA
120 P A
120 P A
154 WA
---- ------- ------- ------- ------- ------- ---338 YT
---- ------- ----
Restore
CID SIA
101 Q R
159 Z R
151 G R
114 K R
100 M R
120 P H
120 H H
154 WR
---- ------- ------- ------- ------- ------- ---338 YR
---- ------- ----
Bypass
CID SIA
572 QB
572 ZB
572 GB
572 KB
572 MB
572 PB
572 PB
572 WB
---- ------- ------- ------- ------- ------- ---572 UB
---- ------- ----
Trouble
CID SIA
---- ------- ------- ------- ------- ------- ------- ------- ------- ------- ------- ------- ------- ------- ------- ------- ------- ----
NOTE: On CID reporting the 3 digit code is preceded by a “1” for new events or a “3” for restore (previous reported) events.
Page 40
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
11-Keypad F-Keyr
Reporting Codes
Menu 11 - Keypad F-Key Reporting Codes
Press RIGHT arrow key to select this menu. Press UP or DOWN arrow keys to select
another menu. The ELK key backs up one menu level. To exit press the * or Exit key.
Referring back to Menu 04-Keypad Definitions, each F Key (F1 thru F6) can be programmed to activate a specific event.
If the programmed “activate event” is an alarm such as: Burg, Fire, Medical, Police Panic, etc., then it is possible to have
an alarm report code transmitted when an F key is used to activate that event. Enter a two digit value for the “A” alarm
report code. To disable the alarm report code enter 00. If the reporting format is SIA or Contact ID, the value can simply
be 01 because the control will automatically produces the correct code according to alarm type using the SIA or Contact
ID protocol. For 4+2 pulse format, enter a value from 01 to FF. To enter the A thru F HEX characters press the RIGHT
arrow key to position the cursor under the desired digit, then press the UP arrow (shift) key once. Each press of the 2
key will now produce the following: 2, A, B, C. Each press of the 3 key will now produce the following: 3, D, E, F.
Press the RIGHT arrow key to cancel shift and move to the next character.
F-Key Report Codes
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
FK01: A=00
r
[KP01 FKey01]
Description of Option
Each Keypad has 6 programmable F keys. This menu displays the F keys starting at
FK01 thru FK06 for Keypad 1, then FK07 thru FK13 for Keypad 2, etc. Use the UP and
DOWN arrow keys to select the appropriate keypad and key, then press the RIGHT arrow
key to programming the code. It may take some experimenting but it is possible to jump
directly to a specific keypad and key by entering a two digit number.
To program the alarm report code press the RIGHT arrow key to move the cursor into the
A= column, then enter a two digit value. Range is 00 to FF. Default is 00 (no report). To
return back to the left column to select another key or keypad press the ELK key
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
FK02:A=00
[KP01 FKey02]
r
NOTE: Each reporting code must be programmed according to the desired reporting
format. However, for SIA and Contact ID formats the actual reporting digits will be
produced by the control according to the type of alarm or event. The only programming
required to enable reporting with the SIA and Contact ID formats is to set the programmed
code to a non zero (0) value. See below:
Based on the F Key Event definition, the CID (Contact ID) or SIA formats will be:
Keypad Alarm RCs
00 = Disabled
01 = Burglar Entry/Exit 1
02 = Burglar Entry/Exit 2
03 = Burglar Perim Inst
04 = Burglar Interior
05 = Burglar Int Follower
06 = Burglar Int Night
07 = Burglar Int Nt Delay
08 = Burglar 24 Hour
09 = Burglar Box Tamper
10 = Fire Alarm
11 = Fire Verified
12 = Fire Supervisory
13 = Aux1 24hr Alarm
14 = Aux2 24hr Alarm
15 = Keyfob
16 = Non-Alarm
17 = Carbon Monoxide
Alarms
CID SIA
---- ---134 BA
134 BA
131 BA
132 BA
132 BA
135 BA
135 BA
133 BA
137 TA
110 FA
110 FA
200 FS
150 UA
150 UA
---- ------- ---162 GA
Keypad Alarm RCs
18 = Emergency Alarm
19 = Freeze Alarm
20 = Gas Alarm
21 = Heat Alarm
22 = Medical Alarm
23 = Police Alarm
24 = Police No Indication
25 = Water Alarm
26 = Key Mom Arm/Disarm
27 = Key Mom Arm Away
28 = Key Mom Arm Stay
29 = Key Mom Disarm
30 = Key On/Off
31 = Mute Audibles
32 = Power Supervisory
33 = Temperature
34 = Analog
Alarms
CID SIA
101 QA
159 Z A
151 GA
114 KA
100 MA
120 P A
120 P A
154 WA
---- ------- ------- ------- ------- ------- ---338 YT
---- ------- ----
NOTE: On CID reporting the 3 digit code will be preceded by a “1”.
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 41
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12-Sys Rpt Code r
Options & Codes
Menu 12 - Sys Report Code Options & Codes
Press RIGHT arrow key to select this menu. Press UP or DOWN arrow keys to select
another menu. The ELK key backs up one menu level. To exit press the * or Exit key.
System Report Codes and Options are global to the entire system such as Low Battery, AC Fail, etc. Using the up/down
arrow keys, select the appropriate option, then press the right arrow key to begin programming that option.
NOTE: Enter a two digit value to enable a report code. To disable a report code enter 00. When SIA or Contact ID is the
reporting format, the two digit value can simply be 01 since the control automatically produces the correct code
according to the SIA or Contact ID protocol. For 4+2 pulse format, enter a value from 01 to FF. To enter the A thru F
HEX characters press the RIGHT arrow key to position the cursor under the desired digit, then press the UP arrow (shift)
key once. Each press of the 2 key will now produce the following: 2, A, B, C. Each press of the 3 key will now produce
the following: 3, D, E, F. Press the RIGHT arrow key to cancel shift and move to the next character. See Appendix for
a summary of the SIA and Contact ID codes.
Sys Rpt Code Options
Description of Option
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
AC Fail Report Delay may be set to delay from 001 to 255 minutes. Valid range is 000 254 minutes. Default setting is 15 minutes. Setting this location to 255 results in no AC
failure annunciation at the keypad or by the dialer.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
AC Fail T (Trouble) code will be reported upon AC failure, after any AC Fail Rpt delay time.
AC Fail R (Restore) will be reported immediately upon restoral of the AC power. Range is
00 to FF. Default is 00 (no report).
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Auto Test code may be periodically reported to verify that the telephone line and internal
communications circuitry is functioning properly. Range is 00 to FF. Default is 00 (no
report).
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
SR04: =00:00 r
Auto Test Hr:Min
Auto Test Hr:Min is normally set to occur during off-peak times. However, if may be set to
occur at any specific hour and minute. This location requires military time format. IE:
7:30 is AM while 19:30 is 7:30pm. Default is 00:00 which is Midnight.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Days Between Auto Test may be set to skip a certain number of days, from 1 to 255. The
default value is 000 which means that the test code, if programmed, will be reported every
day (24 hour interval) from the Auto Test time.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Aux. Overcurrent trouble (T) will be reported when the control’s auxiliary power is
overloaded. A restore (R) will be reported when the overload ceases. Range is 00 to FF.
Default is 00 (no report).
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Exp Module Tbl T (Trouble) will be reported when an enrolled data bus module fails to
respond or is missing. Exp Module Tbl R (Restore) will be reported when the module is
restored. Range is 00 to FF. Default is 00 (no report).
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
This report code may be programmed in order to know when the Installer Level of
Programming has been entered. Range is 00 to FF. Default is 00 (no report).
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
This report code may be programmed to notify when Installer Level Programming is ended.
To prevent unnecessary reports, the report will not transmit until the * key is pressed three
times to signify final end of programming. The report will occur automatically at Midnight if
the * key sequence is not pressed. Range is 00 to FF. Default is 00 (no report).
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
Log 80% Full will be reported whenever the Event Log becomes 80% full. Range is 00 to
FF. Default is 00 (no report). The Elk-RP is required to download the log and/or clear it.
SR01: 015=AC Fail
Rpt Delay - Minr
SR02: T=00 R=00 r
AC Fail Codes
SR03: 00 = Autor
Test Code
SR05: 000=Days r
Between AutoTest
SR06: T=00 R=00 r
Aux Overcurrent
SR07: T=00 R=00 r
Exp Module Tbl
SR08: 00=Instalr
Program Begin
SR09: 00=Instalr
Program End
SR10: 00= Logr
80% Full
Page 42
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
Menu 12 - Sys Report Code Options & Codes (continued)
Sys Rpt Code Options
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
SR11: T=00 R=00 r
Low Battery
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
SR12: T=00 R=00 r
Memory Error
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
SR13: 00= Up/ r
Download End
Description of Option
Low Battery T (Trouble) will be reported if the battery drops below 11.2 Volts. Low Battery
R (Restore) will be eligible to report once the battery has passed a test at 11.5 Volts or
higher. Range is 00 to FF. Default is 00 (no report).
Memory Error T (Trouble) will be reported if the system memory checksum fails. An
upload or review of the programming is the only way to detect where the error occurred.
To clear the error and send a R (Restore) you must enter and exit the installer
programming mode. Range is 00 to FF. Default is 00 (no report).
Up/Download End will be reported upon completion of a Up/Download session as a
verification that the control was accessed. Range is 00 to FF. Default is 00 (no report).
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
Phone Line Fault T (Trouble) will be reported if the Voltage and Current is lost on the
telephone line. Phone Line Fault R (Restore) will report upon restoral of the telephone
line. Range is 00 to FF. Default is 00 (no report).
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
Output 2 T (Trouble) will be reported if an open circuit occurs on Output 2. Output 2 R
(Restore) will be reported upon restoral of the connection. Range is 00 to FF. Default is
00 (no report).
SR14: T=00 R=00 r
Phone Line Fault
SR15: T=00 R=00 r
Output 2 Trouble
Based on the event, the CID (Contact ID) or SIA Codes for System Reporting Codes will be:
System RCs
CID
AC Fail
301
AC Restore
301
Automatic Test
602
Aux Over Current
312
Aux Over Current Restore
312
Expansion Module Trouble 333
Expansion Module Restore 333
Local Programming Begin 627
Local Programming End
628
SIA
AT
AR
RP
YP
YQ
ET
ER
LB
LX
System RCs
Log 80% Full
Low Backup Battery
Low Battery Restore
Memory Error
Remote Programming End
Telephone Line Fault
Telephone Line Restore
Output 2 Trouble
Output 2 Restore
CID
623
302
302
304
412
351
351
322
322
SIA
JL
YT
YR
YF
RS
LT
LR
YA
YH
NOTE: On CID reporting the 3 digit code is preceded by a “1” for new events
or a “3” for restore (previous reported) events.
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 43
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
13-User
Codes
Report
r
Menu 13 - User Report Codes
Press RIGHT arrow key to select this menu. Press UP or DOWN arrow keys to select
another menu. The ELK key backs up one menu level. To exit press the * or Exit key.
NOTE: Enter a two digit value to enable a report code. To disable a report code enter 00. When SIA or Contact ID is the
reporting format, the two digit value can simply be 01 since the control automatically produces the correct code
according to the SIA or Contact ID protocol. For 4+2 pulse format, enter a value from 01 to FF. To enter the A thru F
HEX characters press the RIGHT arrow key to position the cursor under the desired digit, then press the UP arrow (shift)
key once. Each press of the 2 key will now produce the following: 2, A, B, C. Each press of the 3 key will now produce
the following: 3, D, E, F. Press the RIGHT arrow key to cancel shift and move to the next character. See Appendix for
a summary of the SIA and Contact ID codes.
User Report Codes
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
UR001: Selb Prgr
[Name of User]
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
UR001:O=00 C=00r
[Name of User]
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
UR100:O=00 C=00r
Installer Op/Close
Description of Option
Each of the 99 User Codes and the Installer has communicator reporting codes for Open
(disarm) and Close (arm). Using the up/down arrow keys, select the appropriate user,
then press the right arrow key to begin programming of that user’s report codes.
The cursor starts at the 00 beside O (Open). Enter the desired two digit reporting code
and press the right arrow key to advance to the C (Close). Range is 00 to FF. Default is
00 (no report). To jump the cursor to the next report code without changing this one
simply press the right arrow key. The next press of the right arrow key will advance back
to the beginning screen.
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
UR101:O=00 C=00r
Up/Dnload Op/Cl
The CID (Contact ID) or SIA Codes for User Reporting Codes are:
User RCs
Open
Close
CID
SIA
401
401
OP
CL
NOTE: On CID reporting the 3 digit code is preceded by a “1” for an opening
event or a “3” for a closing event.
Page 44
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
Menu 14 - Wireless Definitions
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
12345678901234567890123456789012123
Press RIGHT arrow key to select this menu. Press UP or DOWN arrow keys to select
another menu. The ELK key backs up one menu level. To exit press the * or Exit key.
14-Wireless
Definitions
r
The Control is compatible with the Caddx brand wireless receivers: NX408E (8 zones), NX416E (16 zones), and NX448E
(48 zones) and transmitters. Only 1 Receiver may be connected to the Control. A special 5 pin wiring harness (ELKWO35A) is required and it plugs into connector J3 “Aux Data Bus” located on the upper right side of the board.
Requires
ELK-W035A
Wiring Assembly
Control Panel
J3
AUX
B
A
NEG
C
+
+12V
Connect
to J3
Caddx Brand Receiver Board
NX-408E
NX-416E
NX-448E
Brown (n/a)
White (n/a)
Red
Black
Green
+
A Data
SET ALL FOUR ADDRESS
SWITCHES TO OFF!
Wiring Diagram for Caddx NX Receiver
WirelessDefinitions
Description
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
The Wireless Definitions menu is broken into four parts: 1:Receiver Options, 2:Xmitter
Options, 3:Xmitter Enroll, and 4:Keyfob Event Definitions. To program Receiver Options
press the right arrow key. To move to Transmitter Options, Xmitter Enroll, or Keyfob
Event Definitions press the up or down arrow keys.
1:Rec Selb Prgr
Receiver Options
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
RO1:=0 Rec Sizer
0=8 ZoneReceiver
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
RO2:=00 ZnBank r
StartingZone xxx
02=(Zone 17)
12=(Zone 97)
R01: Receiver Size. Identifies the size of the connected Receiver so the appropriate
number of zones may be reserved. For the NX408E 8 zone receiver enter a 0, for a
NX416E 16 zone receiver enter a 1, for a NX448E 48 zone receiver enter a 2. The
Control will recognize these as wireless, starting from the ZnBank setting option.
R02:ZnBank Starting Zone. Identifies where the first wireless zone begins. Using the
receiver size and this starting number, the desired number of zones will be blocked out.
If another zone expander (hardwired) is encountered that results in a duplicate zone, the
Control will error tone and return to a 00 setting. To resolve the conflict: move the
starting zone to another setting, move the conflicting zone expander to another address,
or reduce the receiver size setting. Valid starting zones must be increments of 16:
04=(Zone 33) 06=(Zone 49) 08=(Zone 65) 10=(Zone 81)
14=(Zone 113) 16=(Zone 129) 18=(Zone 145) 20=(Zone 161) 22=(Zone 177)
Example: Entering a value of 2 for receiver size and 02 for starting zone would block out
48 zones from 17 thru 64 as wireless. NOTE: If an 8 zone receiver is installed, the upper
8 zones are not available (wasted) as far as the control is concerned. Receivers with
multiples of 16 zones (NX416E and NX448E) are therefore better economic choices.
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
RO3:=24 Hours r
Reg. Supervision
R03: Reg. Supervision sets the interval, in hours, for “check-in” by transmitters which are
programmed for “Supervision Type 1”, see transmitter option 01. Valid range is 001 to
255 hours, however a value lower than 4 is not recommended. Default value is 24.
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
R04: Fire Supervision sets the interval, in hours, for “check-in” by transmitters which are
programmed for “Supervision Type 2” (Fire), see transmitter option 02. Valid range is 001
to 255 hours, however a value lower than 4 is not recommended. Default value is 004.
RO4:=004 Hours r
Fire Supervision
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 45
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
2:Xmit Selb Prgr
Transmitter Optr
WZnxxx:Selr Prgr
Wireless Zone
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
WZnxxx 01:=No r
Enable Transmitr
Press the RIGHT arrow key to select 2:Transmitter Options.
Use the UP and DOWN arrow keys to locate a particular wireless transmitter. Press
the RIGHT arrow key to select and program the displayed transmitter.
Option 01 “Enable Transmitter” will be set to Yes whenever a new transmitter is
enrolled. To disable or remove this transmitter program this to No.
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
Option 02 selects the “Supervision Type” for the transmitter. 0=No Supervision,
1=Regular Supervision, 3=Fire Supervision. See receiver options R02 and R03 for
supervision time values. Default is 1.
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
Option 03 is used to disable the internal reed switch on the Caddx transmitter so that
an external switch may be hardwired to the transmitter. Refer to the Caddx NX
Series Receiver Instructions for complete transmitter details.
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
Option 04 is used to select whether an external switch should be normally open (N/O)
or normally closed (N/C). For N/O set option to No. For N/C set option to Yes. Refer
to the Caddx NX Series Receiver Instructions for complete transmitter details.
WZnxxx02:=0
r
Supervision Type
WZnxxx 03:=No r
Enable Option 1
WZnxxx 04:=No r
Enable Option 2
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
WZnxxx 05:=001
Keyfob User ID
r
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
3:Learn Selb Prgr
WirelessTransmtr
WZone = xxx r
TransmtToEnroll
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
WZone = xxx Push
TransmiterButton
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
1234567890123456789012345678901212345
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
123456789012345678901234567890121234
4:KeyfobSelb Prgr
Event Definition
Keyfob Button=1r
1000=Event
Option 05 sets the User ID that will be logged when a keyfob is used to arm or disarm.
Valid range is 001 to 255. If assigned as 001 to 099, the keyfob will mirror the keypad
user codes. If any of those users are programmed for opening/closing reports, they will
be reported regardless of whether a keypad code OR keyfob was used. NOTE: Since
there are no opening/closing report codes beyond user 99, any keyfob ID that is set
higher that 99 will utilize the opening/closing report code for User 99.
Press the RIGHT arrow key to select 3:Learn Wireless Transmitters.
Press the UP or DOWN arrow keys to locate the wireless zone that you wish to enroll.
Then press the RIGHT arrow key to continue.
Go to the transmitter and press the tamper or enroll button. The keypad should emit a
short tone when the transmitter becomes enrolled.
Press the RIGHT arrow key to select 4:Keyfob Event Definition
Press the UP or DOWN arrow keys to locate the keyfob button to program. There are
a total of 8 programmable buttons, however only 6 of the 8 may be used on the keyfob.
The valid activation events programmable for each button ranges from 0000-0030
(utilizing the Zone Definitions table) and 2001-2032 (utilizing Appendix A, Event Codes).
The standard buttons are as follows: Button 1 (Lock), 2 (Unlock), 3 (Light), and 4
(Asterisk). For Button 7 press a combination of buttons 1 & 2 together at the same
time. For Button 8 press a combination of buttons 3 & 4 together at the same time.
Button 3 on a keyfob can be changed to 5 by setting the transmitter Option 1 to Yes.
Button 4 on a keyfob can be changed to 6 by setting the transmitter Option 2 to Yes.
Page 46
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
Section 4 - PC Programming and Automation Capabilities
4.1 ELK-RP Software
ELK-RP (RP) is a Windows based software package that is compatible with Windows 95
and later. It features an extremely intuitive user interface and contains all data in a central
database. RP can be run on a single PC or over a local area network (LAN) with multiple
operators. In addition to the traditional security programming features, RP allows you to
create and manage the automation functionality in the control. The following information is a brief overview including
illustrations of the various screens. Please refer to RP’s on-line help file for specific operation details.
4.1.1
RP Connection Methods
There are 3 methods for the RP software to connect with the control. Regardless of the method, the control’s serial number
and RP access code MUST match in order for the connection to be successful. The connection methods are:
1. Direct using Com_ (PC Com port) - Requires an
M1EZ8MSI Main Serial Port board and a 9 pin serial
cable. Data transfer is 115,200 baud. NOTE: If your
computer only has a USB port, an approved
converter (USB to RS-232) is available from Radio
Shack and from ELK (ELK-USB232).
2. Dial-up using Modem and phone line - RP is
compatible with virtually all computer modems, even
56k modems. This is due to the controls built-in V.22 bis “True” modem, which handles data transfer at 2,400 baud. The 6
dial-up options are:
Fully Automatic - RP dials the control phone number and listens for the control to answer on it’s “rings until answer” setting.
If an answering machine answers, RP will transmit codes to override it automatically.
Prompt when answer - RP dials and listens for the control to answer. It waits for a manual OK before connecting.
Dial, hang up, dial again - This is faster than waiting on the control’s “rings until answer” setting. It is also useful for
reaching premises that have telephone company answer/forward services. The control must be enabled for this option.
After dialing, RP leaves the PC speaker on, and prompts you to click “Hang-up” after you hear two rings. It then forces a
time delay before allowing you to click OK to start the second dial. As long as the control properly detects the first two
rings and subsequent hang-up, it will wait up to 45 seconds for a second call and answer that call on the first ring.
Customer will force answer - Similar to method 1 except the User must enter keypad menu 8, option 5, item 1 to force the
control to answer. This is necessary if the “rings until answer” or “dial/hang-up/dial” options are not programmed.
Telephone connection already established - If a voice connection is already established using the control’s phone line and
the PC’s phone line, this method can be used to take over the connection and initiate an immediate connection.
3. Network - With an optional ELK-M1XEP Ethernet Port module you can connect over a Local or Wide Area Network. (Contact
ELK for details)
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 47
4.1.2
Check for Conflicts
During the connect and disconnect process RP performs an automatic check of the data stored in the control and compares it
the database. If there are any conflicts (differences), a pop-up resolution window display them and allows corrections to be
made. ELK regards “Check for Conflicts” to be an especially important feature. It can point out any changes that have
occurred such as a user having added or changed a code. The resolution window allows you to receive the control’s data into
the database (accept the local version) or send the RP data to the control (accept the database version). NOTE: Checking for
conflicts adds considerable time to the connect/disconnect process, especially on dial-up connections. For this reason,
the automatic check for conflicts may be disabled from the SETUP menu. A manual Check for Conflicts can be selected
from the Send/Rcv icon.
4.1.3
Sending and Receiving Data
RP allows many options and groups of options to be sent or received individually, which greatly reduces the on-line connect
time if there are only a few items to be changed. However, a full send or receive occurs very quickly, thanks to the built-in V.22
bis “True” Modem. RP features easy to use menus & toolbar icons and makes extensive use of the right mouse button to
perform operations. Try right clicking on any item or icon to see the available options.
4.2 Update/Verify Firmware in the Control and Peripherals
The control stores it’s operating firmware in “Flash” memory. This state-of-the-art memory allows electronic field updates to
the control and its peripherals, and eliminates the old fashion method of changing IC chips or shipping boards back to the
factory. As new firmware updates become available, they will be posted on ELK’s Dealer ONLY restricted website found at
www.elkproducts.com. NOTE: Firmware updating can only be done from a Direct to PC Com port connection or an optional
Ethernet Network connection. Due to the amount of data that has to be transferred, Dial-up connections cannot be used
to perform firmware updates.
How to Update Firmware:
1. In order to make a RS232 Serial connection from an EZ8 Control to a PC the EZ8 must be equipped with an ELKEZ8MSI Main Serial Port Interface. This provides a standard RS232 Port with operating speed up to 115,200.
2. Connect a 9 pin serial cable from the Computer’s Serial Port to the 9 Pin RS232 Connector on EZ8MSI.
3. Start RP and open the account belonging to that particular control. Click on the Connection menu icon and establish
a connection using the Direct using Com_ option.
4. Click on Update/Verify Firmware from the Send/Rcv menu icon.
5. On the Update/Verify screen, select the device to be updated (Control, Keypad, etc.) along with the “Update to new
firmware” option. Then click Continue.
6. The Update Firmware screen displays the device name, the current Firmware, Hardware, and Bootware version, and
a pull down window for selecting the firmware version to use on the update. Always select the latest firmware version
(highest number). Be sure to save all update (.bin) files that are downloaded or received via CDROM into the
~Program Files\ElkRP\Updates directory on your computer. This is where RP looks for all update files.
7. Click on the check box for “Update”. If “Reprogram” or “Rollback” is displayed the firmware file is the same as OR
older that what is in the control. Reprogramming with the same firmware is a waste of time but was included for
factory testing purposes. Rollback is not recommended except under the guidance of Elk Technical Support.
NOTE: The option for “Verify existing firmware” on the Update/Verify screen is normally not required except for
factory diagnostics. If the control has multiple keypads, expanders, etc., RP will display the details about each
one onscreen with a check box for selecting units for updating.
Page 48
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
4.3 Automation Rules and Attributes
The Automation Programming software offers powerful, easy to setup and manage, life style enhancement features. The
automation programming allows mixing and matching of lighting components, outputs (relays or voltage), thermostats,
temperature sensors, and all the security inputs and features to integrate functions that add value and appeal to the owner/
user. Lights can be set to turn on and off in response to a time or day, a certain sensor, or according to the arm/disarm status
of the security control. Outputs can be set to control door strikes, irrigation sprinklers, circulating pumps valves, etc.
The power behind the automation features is the unique RULES Engine. Rules are expressions of what you would like to
happen at a given time or in response to a set of circumstances. The following information is intended to provide an overview
of the vast automation features in the control.
TASKS - A Task is similar to a computer macro, in that a single activation can result in multiple actions or events. The
actions and triggering of a Task must be written or developed in a Whenever/And/Then Rule. The purpose of the task
screen is to assign each task its own 16 character description and the ability to “Show” on the keypad or the telephone remote
control menu. Up to 32 Tasks can be programmed. Examples are “Water the Lawn” which could be used to turn on a series
of outputs or relays to control underground water valves for a certain time duration. “Welcome Home” could be task used to
control a series of lights at a given time or day or in response to someone disarming the security system. The following
shows several tasks.
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 49
LIGHTING - The control can handle up to 256 Light (or appliance) devices. Each is assigned to one of 256 addresses. Each
devices is displayed in columnar format with the following options and settings: Name - Each device can be given a 16
character name (description) which is displayed on the keypad when the light is being controlled. Format - This pull down
box selects the protocol of the device. The available Lighting formats are: Standard, Extended, Preset dim, Compose, Serial
Port. The Serial port format is for UPB, ALC, Centralite, others through an ELK-M1XSP Lighting/Thermostat/Serial Expander
Interface. Type - This pull down box selects the whether the device is a: On/Off Switch, Dimmer, or Appliance. Show - If this
box is checked the device will appear “show” on the keypad and telephone remote as you scroll through the automation
control menus. 2-way - This checkbox is used to record whether the device is capable of replying back to commands. NOTE:
Additional lighting formats are in development, including the new Z-Wave wireless devices. Even if a lighting product is
not directly supported, it is always possible to use RS-232 ASCII strings for communicating lighting control.
OUTPUTS - These can be in the form of voltage only, relays, or a combination of the two. Up to 204 outputs may be controlled.
The first 32 outputs have a 16 character description and the “Show” on keypad or telephone remote option. However, any
output may be controlled from the keypad by entering its number. Outputs can be used to actuate door locks, motors, fan,
pumps, etc.
SUNRISE/SUNSET - Sunrise and sunset can be used to control lighting and other entities. This section is the setup for the
built-in Astronomical clock, which is capable of calculating sunrise and sunset times automatically. The inputs necessary to
setup the control for sunrise/sunset are latitude, longitude, and the time zone value where the control is installed. Latitude/
longitude information can often be found printed on city or state highway maps, or it can be researched on the internet. After
entering the required information, click calculate and then send to the control.
NOTE: The Time
Zone automatically
assumes “standard
time”. Therefore, the
calculated times will
reflect standard time.
If the control is set for
“Observe Daylight
Savings Time” the
sunrise/sunset times
will be adjusted by the
control accordingly.
Page 50
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
CUSTOM SETTINGS - These are 20 memory locations which may be assigned a 12 character description, a function type
(one of 3), and a starting value. An authorized user can then access the custom settings from keypad user menu 7Automation Custom Settings, and modify the value whether it be a numeric value, a timer (seconds), or a time-of-day.
Incorporating custom settings in rules provides the user the ability to modify how the rule will operate. For instance, the user
can modify the time or duration for the lawn sprinklers which have been programmed to turn on automatically. The function
types include: A 5 digit raw number with a range of 00000 to 65,535, a 5 digit timer (seconds) with a range of 00000 to 65,535
seconds, or a Time (time of day) which is formatted as 00:00 with a range of 00:00 to 23:59.
COUNTERS - These memory locations (often called flags) can be set, incremented, decremented, or compared by an
automation rule to track an event or keep up with how many times an event has occurred. There are a total of 64 counters.
Each can be programmed with a 12 character description, making it easy to reference in an automation rule.
THERMOSTATS - HVAC Thermostats may be read and/or controlled by the automation rules engine. This menu allows each
thermostat to be assigned a 12 character description for easy reference in an automation rule. The compatible thermostats
are: RCS, Aprilaire, and HAI. Due to the various data protocols, a Lighting/Thermostat/Serial Interface Expander (ELK-M1XSP)
is needed to couple the M1 data bus to HVAC thermostats. Depending on the brand of thermostat, its wiring interface (RS232 or RS-485), and the model of control that you are installing, up to 16 HVAC thermostats can be controlled. Many
communicating thermostats operate stand-alone when they are not being remotely commanded by an automation controller.
TEXTS - This section allows custom text messages to be constructed and formatted. These messages can be transmitted to
an LCD keypad or out one of the RS232 serial ports to a PC or some other type of equipment. I.E. Touchscreen, Lighting
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 51
centers, etc. A message to the keypad could be “Happy Birthday” or “Please Pay Your Bill”, while a message going out a serial
port might be a series of ASCII characters formatted to a certain manufacturers protocol. Special options built into this menu
include: automatic display of temperature readings from Zone Temperature Sensors (ELK-M1ZTS) and from the temperature
sensor built into an LCD Keypad. The sending or receiving of text messages is controlled by the automation rules engine.
NOTE: Text messages share the same memory space as rules. The total number of text messages and rules combined
cannot exceed the total amount of rule space in the control.
Page 52
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
RULES - This section essentially brings all the power of the automation together. Rules consist of three major elements: A
WHENEVER (“triggering”) condition, one or more ANDs (“qualifiers”), and one or more THENs (“activations”). Rules utilize the
various elements of the previously described sections in addition to the many control conditions (arm, disarm, alarms, etc.),
plus many of the event codes listed in Appendix A. For example: A rule might be triggered by a Task to activate a specific light
and output, but only if the control is armed in a specific mode.
WHENEVER - The first element of a rule and the starting point of every rule is a triggering event. Every rule must have a
triggering event in order to be started. A triggering event can be a time of day occurrence, a zone opening or closing, the
security system going from armed to disarmed, a light changing from on to off, or literally hundreds of other events.
Below are some examples of WHENEVER elements:
Example 1 = WHENEVER THE TIME IS 08:00AM
Example 2 = WHENEVER Living Rm Light [6 (A6)] IS TURNED ON
An important point to remember is that a WHENEVER gets triggered by the transition of its event from one state to
another. In example 1, the trigger occurs when the time of day goes from 07:59AM to 08:00AM. In example 2, the trigger
occurs when the living room light goes from off to on. Some WHENEVER elements may even include the word
“BECOMES”, which clearly implies that the event has to change from its current condition and “become” the alternate
condition. Just remember, a rule can only be triggered by the transition of an event from one condition to another.
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 53
AND - The second and optional element of a rule is a qualifier. Rules can have one or more qualifiers OR none at all. Even
though qualifiers are not required, they are ideal for filtering out actions that should not occur under certain
circumstances. A qualifier can be a time, day(s), the state of light or dark, the state of a zone, output, or light, and
hundreds of other variables. The state of light or dark can be determined by the Sunrise/Sunset settings from the
control’s Astronomical Clock. Below are some examples of AND (qualifiers):
Example 3 = AND Front Door (Zn 1) IS NOT SECURE
Example 4 = AND THE DAY(S) OF THE WEEK IS/ARE -M-W-FExample 5 = AND IT IS DARK OUTSIDE
Example 6 = AND John’s House (Area 1) IS ARMED AWAY
THEN - The third and final element of a rule is the action that you wish to occur as a result of the Rule being triggered and
all the qualifiers being true. Below are some examples of THEN actions:
Example 7 = THEN TURN Air Cond (Out 9) OFF
Example 8 = THEN TURN Living Rm Light [6 A6)] OFF
Example 9 = THEN SET Main Floor (Tstat 1) OFF
Example 10 = THEN TURN All Lights On
Here is an example of a rule used to turn off the air condition anytime the front door is left open by the kids. It consists of a 30
second timer for the WHENEVER trigger an AND to test the door’s open/closed state, and a THEN to turn off the output that
controls the air condition.
WHENEVER EVERY 30 SECONDS
AND Front Door (Zn 1) IS NOT SECURE
THEN TURN Air Cond (Out 9) OFF
Page 54
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
Examples of Rules - Shown below are a series of rules that should help illustrate the power and results that rules can
provide. Look closely at the ones that have multiple ANDs and THENs. Rules with Multiple ANDs and THENS work as
follows: When the WHENEVER element is triggered, each one of the AND elements is evaluated to determine if the condition
its testing is true. If any one of the ANDs are not true, the rule engine stops executing the rule immediately. However, if all
ANDs are true then the rule engine moves on to the THEN elements, executing each one of them.
Rule 1 is an energy saving example. It automatically turns off the Porch lights at 8:00AM everyday if it is light outside.
Rule 2 is a courtesy light example. It will turn on the Porch light for 5 minutes when the Front door opens (exiting the building)
provided it is dark outside and the control has been armed to the away mode.
Rule 3 is a comfort example. It periodically (every 20 seconds) checks the temperature reading of the Outdoor Temp sensor
and turns on the Porch Fan if the temperature becomes greater than 90 degrees. NOTE: An additional AND element
could be added to prevent the fan from operating on certain days or at certain times.
Rule 4 is another energy savings example. It adjusts the cooling setpoint of the Main Floor Thermostat to 85 degrees
whenever the control is armed to the away mode.
Rule 5 is especially great for a homeowner arriving home after dark. If they are equipped with an RF (wireless) Keyfob and
they press button #3, the rule will turn on the outside Flood lights and Porch lights for 5 minutes, provided it is dark
outside and the Flood lights are not already on. If the Floodlights were already on the rule would stop. This prevents
the lights from going off after 5 minutes if you intentionally had already turned them on manually.
Rule 6 shows how an ASCII string coming in from the serial port (port 0) could be used to unlock a door strike for 10 seconds
and announce “Access Allowed”. This string could come from Access Control system.
In this last example, three rules are used to chirp the outside
siren based on the input of a RF Keyfob to arm the control.
Rule 8 makes the siren chirp once if the control successfully
arms when the user presses button 1.
Rule 9 makes the siren chirp twice if the control disarms when
the user presses button 2
Rule 10 makes the siren chirp four times (error tone) if the
control fails to arm when the user presses button 1.
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 55
Appendix A - Event Codes
Event Codes are four digit numbers used to represent alarms, troubles, arm/disarms, restores, and various other conditions that occur within the control. For the
most part, they are used only internally by the control’s software. For example: turning on the alarm output. However, there are cases where the installer may need
these codes. Case #1 - Keypad F key programming. Each of the Keypad F keys may be programmed to activate a particular condition such as Emergency Panic
Alarm. See Menu 04 - Keypad Definitions. The activation event code can be any of the zone definition codes. The F1 key may also be programmed to light up or
“illuminate” when a condition is active. The F1 key can illuminate when the Emergency Panic Alarm is active by programming the four digit event code 1011 =
Emergency Alarm. Case #2 - Event History log. Each of the 512 entries in the event history log is represented by one of these 4 digits event codes, along with the
time, date, area, and/or user code. It may be necessary or helpful to have these codes handy to fully interpret the log.
Event Description
Reset
0000 or 1000 =No Event
N
1001 = Fire Alarm
TMC
1002 = Fire Supervisory
TMC
1003 = Burglar Alarm, Any Area TMCB
1004 = Medical Alarm, Any Area TMC
1005 = Police Alarm, Any Area
TMC
1006 = Aux1 24 hr, Any Area
TMC
1007 = Aux2 24 hr, Any Area
TMC
1008 = CO Alarm, Any Area
TMC
1009 = Emergency Alm, Any Area TMC
1010 = Freeze Alarm, Any Area
TMC
1011 = Gas Alarm, Any Area
TMC
1012 = Heat Alarm, Any Area
TMC
1013 = Water Alarm, Any Area
TMC
1014 = Alarm, Any Area
TMC
1015 = Burglar Alarm in Area 1
1016 = Burglar Alarm in Area 2
1017 = Burglar Alarm in Area 3
1018 = Burglar Alarm in Area 4
1019 = Burglar Alarm in Area 5
1020 = Burglar Alarm in Area 6
1021 = Burglar Alarm in Area 7
1022 = Burglar Alarm in Area 8
TMC
TMC
TMC
TMC
TMC
TMC
TMC
TMC
1023 = Medical Alarm in Area 1
1024 = Medical Alarm in Area 2
1025 = Medical Alarm in Area 3
1026 = Medical Alarm in Area 4
1027 = Medical Alarm in Area 5
1028 = Medical Alarm in Area 6
1029 = Medical Alarm in Area 7
1030 = Medical Alarm in Area 8
TMC
TMC
TMC
TMC
TMC
TMC
TMC
TMC
1031 = Police Alarm in Area 1
1032 = Police Alarm in Area 2
1033 = Police Alarm in Area 3
1034 = Police Alarm in Area 4
1035 = Police Alarm in Area 5
1036 = Police Alarm in Area 6
1037 = Police Alarm in Area 7
1038 = Police Alarm in Area 8
TMC
TMC
TMC
TMC
TMC
TMC
TMC
TMC
1039 = Aux1 24 hr in Area 1
1040 = Aux1 24 hr in Area 2
1041 = Aux1 24 hr in Area 3
1042 = Aux1 24 hr in Area 4
1043 = Aux1 24 hr in Area 5
1044 = Aux1 24 hr in Area 6
1045 = Aux1 24 hr in Area 7
1046 = Aux1 24 hr in Area 8
TMC
TMC
TMC
TMC
TMC
TMC
TMC
TMC
1047 = Aux2 24 hr in Area 1
1048 = Aux2 24 hr in Area 2
1049 = Aux2 24 hr in Area 3
1050 = Aux2 24 hr in Area 4
1051 = Aux2 24 hr in Area 5
1052 = Aux2 24 hr in Area 6
1053 = Aux2 24 hr in Area 7
1054 = Aux2 24 hr in Area 8
TMC
TMC
TMC
TMC
TMC
TMC
TMC
TMC
1055 = CO Alarm in Area 1
1056 = CO Alarm in Area 2
1057 = CO Alarm in Area 3
1058 = CO Alarm in Area 4
1059 = CO Alarm in Area 5
1060 = CO Alarm in Area 6
1061 = CO Alarm in Area 7
1062 = CO Alarm in Area 8
TMC
TMC
TMC
TMC
TMC
TMC
TMC
TMC
Page 56
Event Description
Reset
1063 = Emergency Alm in Area 1 TMC
1064 = Emergency Alm in Area 2 TMC
1065 = Emergency Alm in Area 3 TMC
1066 = Emergency Alm in Area 4 TMC
1067 = Emergency Alm in Area 5 TMC
1068 = Emergency Alm in Area 6 TMC
1069 = Emergency Alm in Area 7 TMC
1070 = Emergency Alm in Area 8 TMC
1071 = Freeze Alarm in Area 1
1072 = Freeze Alarm in Area 2
1073 = Freeze Alarm in Area 3
1074 = Freeze Alarm in Area 4
1075 = Freeze Alarm in Area 5
1076 = Freeze Alarm in Area 6
1077 = Freeze Alarm in Area 7
1078 = Freeze Alarm in Area 8
TMC
TMC
TMC
TMC
TMC
TMC
TMC
TMC
1079 = Gas Alarm in Area 1
1080 = Gas Alarm in Area 2
1081 = Gas Alarm in Area 3
1082 = Gas Alarm in Area 4
1083 = Gas Alarm in Area 5
1084 = Gas Alarm in Area 6
1085 = Gas Alarm in Area 7
1086 = Gas Alarm in Area 8
TMC
TMC
TMC
TMC
TMC
TMC
TMC
TMC
1087 = Heat Alarm in Area 1
1088 = Heat Alarm in Area 2
1089 = Heat Alarm in Area 3
1090 = Heat Alarm in Area 4
1091 = Heat Alarm in Area 5
1092 = Heat Alarm in Area 6
1093 = Heat Alarm in Area 7
1094 = Heat Alarm in Area 8
TMC
TMC
TMC
TMC
TMC
TMC
TMC
TMC
1095 = Water Alarm in Area 1
1096 = Water Alarm in Area 2
1097 = Water Alarm in Area 3
1098 = Water Alarm in Area 4
1099 = Water Alarm in Area 5
1100 = Water Alarm in Area 6
1101 = Water Alarm in Area 7
1102 = Water Alarm in Area 8
TMC
TMC
TMC
TMC
TMC
TMC
TMC
TMC
1103 = Any Alarm in Area 1
1104 = Any Alarm in Area 2
1105 = Any Alarm in Area 3
1106 = Any Alarm in Area 4
1107 = Any Alarm in Area 5
1108 = Any Alarm in Area 6
1109 = Any Alarm in Area 7
1110 = Any Alarm in Area 8
TMC
TMC
TMC
TMC
TMC
TMC
TMC
TMC
1111 = Any Keypad Code-Lockout
1112 = Keypad 01 Code-Lockout
1113 = Keypad 02 Code-Lockout
1114 = Keypad 03 Code-Lockout
1115 = Keypad 04 Code-Lockout
1116 = Keypad 05 Code-Lockout
1117 = Keypad 06 Code-Lockout
1118 = Keypad 07 Code-Lockout
1119 = Keypad 08 Code-Lockout
1120 = Keypad 09 Code-Lockout
1121 = Keypad 10 Code-Lockout
1122 = Keypad 11 Code-Lockout
1123 = Keypad 12 Code-Lockout
1124 = Keypad 13 Code-Lockout
1125 = Keypad 14 Code-Lockout
1126 = Keypad 15 Code-Lockout
1127 = Keypad 16 Code-Lockout
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Event Description
Reset
1128 = Fire Trouble, Any Zone
TMC
1129 = Burglar Trouble, Any Zone TMC
1130 = Fail to Communicate Tbl
N
1131 = RF Sensor Low Battery Tbl
N
1132 = Lost ANC Module Trouble
N
1133 = Lost Keypad Trouble
N
1134 = Lost Input Expander Tbl
N
1135 = Lost Output Expander Tbl
N
1136 = EEprom Memory Error Tbl
C
1137 = Flash Memory Error Trouble C
1138 = AC Failure Trouble
N
1139 = Control Low Battery Trouble N
1140 = Control Over Current Trouble N
1141 = Expansion Module Trouble
N
1142 = Output 2 Supervisory Tbl
N
1143 = Telephone Line Fault Tbl
1144 = Restore Fire Zone
1145 = Restore Fire Supv Zone
1146 = Restore Burglar Zone
1147 = Restore Medical Zone
1148 = Restore Police Zone
1149 = Restore Aux1 24 hr Zone
1150 = Restore Aux2 24 hr Zone
1151 = Restore CO Zone
1152 = Restore Emergency Zone
1153 = Restore Freezer Zone
1154 = Restore Gas Zone
1155 = Restore Heat Zone
1156 = Restore Water Zone
1157 = Communication Fail Restore
1158 = AC Fail Restore
1159 = Low Battery Restore
1160 = Control Over Current Restore
1161 = Expansion Module Restore
1162 = Output 2 Restore
1163 = Telephone Line Restore
1164 = Alarm Memory
1165 = Alarm Memory in Area 1
1166 = Alarm Memory in Area 2
1167 = Alarm Memory in Area 3
1168 = Alarm Memory in Area 4
1169 = Alarm Memory in Area 5
1170 = Alarm Memory in Area 6
1171 = Alarm Memory in Area 7
1172 = Alarm Memory in Area 8
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
A
TMC
TMC
TMC
TMC
TMC
TMC
TMC
TMC
1173 = Area Armed
1174 = Area Disarmed
1175 = Area 1 Arm State
1176 = Area 2 Arm State
1177 = Area 3 Arm State
1178 = Area 4 Arm State
1179 = Area 5 Arm State
1180 = Area 6 Arm State
1181 = Area 7 Arm State
1182 = Area 8 Arm State
N
N
N
N
N
N
N
N
N
N
1183
1184
1185
1186
1187
1188
1189
1190
N
N
N
N
N
N
N
N
= Area
= Area
= Area
= Area
= Area
= Area
= Area
= Area
1
2
3
4
5
6
7
8
is Armed Away
is Armed Away
is Armed Away
is Armed Away
is Armed Away
is Armed Away
is Armed Away
is Armed Away
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
Event Description
1191 = Area 1 is Armed
1192 = Area 2 is Armed
1193 = Area 3 is Armed
1194 = Area 4 is Armed
1195 = Area 5 is Armed
1196 = Area 6 is Armed
1197 = Area 7 is Armed
1198 = Area 8 is Armed
Reset
N
N
N
N
N
N
N
N
Stay
Stay
Stay
Stay
Stay
Stay
Stay
Stay
1199 = Area 1 is Armed Stay Instant
1200 = Area 2 is Armed Stay Instant
1201 = Area 3 is Armed Stay Instant
1202 = Area 4 is Armed Stay Instant
1203 = Area 5 is Armed Stay Instant
1204 = Area 6 is Armed Stay Instant
1205 = Area 7 is Armed Stay Instant
1206 = Area 8 is Armed Stay Instant
N
N
N
N
N
N
N
N
1207 = Area 1 is Armed Night
1208 = Area 2 is Armed Night
1209 = Area 3 is Armed Night
1210 = Area 4 is Armed Night
1211 = Area 5 is Armed Night
1212 = Area 6 is Armed Night
1213 = Area 7 is Armed Night
1214 = Area 8 is Armed Night
N
N
N
N
N
N
N
N
1215
1216
1217
1218
1219
1220
1221
1222
=
=
=
=
=
=
=
=
Area
Area
Area
Area
Area
Area
Area
Area
1
2
3
4
5
6
7
8
is
is
is
is
is
is
is
is
Armed
Armed
Armed
Armed
Armed
Armed
Armed
Armed
Night
Night
Night
Night
Night
Night
Night
Night
Instant
Instant
Instant
Instant
Instant
Instant
Instant
Instant
N
N
N
N
N
N
N
N
1223 = Area 1 is Armed Vacation
1224 = Area 2 is Armed Vacation
1225 = Area 3 is Armed Vacation
1226 = Area 4 is Armed Vacation
1227 = Area 5 is Armed Vacation
1228 = Area 6 is Armed Vacation
1229 = Area 7 is Armed Vacation
1230 = Area 8 is Armed Vacation
N
N
N
N
N
N
N
N
1231 = Area 1 is Force Armed
1232 = Area 2 is Force Armed
1233 = Area 3 is Force Armed
1234 = Area 4 is Force Armed
1235 = Area 5 is Force Armed
1236 = Area 6 is Force Armed
1237 = Area 7 is Force Armed
1238 = Area 8 is Force Armed
N
N
N
N
N
N
N
N
1239 = Zone Bypassed
1240 = All Zones Unbypassed
1241 = Burglar Zone Fault
N
B
N
1242 = Burglar Status
1243 = Area 1 Burglar Status
1244 = Area 2 Burglar Status
1245 = Area 3 Burglar Status
1246 = Area 4 Burglar Status
1247 = Area 5 Burglar Status
1248 = Area 6 Burglar Status
1249 = Area 7 Burglar Status
1250 = Area 8 Burglar Status
N
N
N
N
N
N
N
N
N
M1EZ8 Installation and Programming
Appendix A - Event Codes (cont.)
Event
Description
Reset
1251 = Area 1 Chime Mode
1252 = Area 2 Chime Mode
1253 = Area 3 Chime Mode
1254 = Area 4 Chime Mode
1255 = Area 5 Chime Mode
1256 = Area 6 Chime Mode
1257 = Area 7 Chime Mode
1258 = Area 8 Chime Mode
N
N
N
N
N
N
N
N
1259 = Area 1 Chime Alert
1260 = Area 2 Chime Alert
1261 = Area 3 Chime Alert
1262 = Area 4 Chime Alert
1263 = Area 5 Chime Alert
1264 = Area 6 Chime Alert
1265 = Area 7 Chime Alert
1266 = Area 8 Chime Alert
B
B
B
B
B
B
B
B
1267
1268
1269
1270
1271
1272
1273
1274
1275
= Entry Delay Active
= Area 1 Entry Delay
= Area 2 Entry Delay
= Area 3 Entry Delay
= Area 4 Entry Delay
= Area 5 Entry Delay
= Area 6 Entry Delay
= Area 7 Entry Delay
= Area 8 Entry Delay
N
N
N
N
N
N
N
N
N
1276
1277
1278
1279
1280
1281
1282
1283
1284
= Exit Delay Active
= Area 1 Exit Delay
= Area 2 Exit Delay
= Area 3 Exit Delay
= Area 4 Exit Delay
= Area 5 Exit Delay
= Area 6 Exit Delay
= Area 7 Exit Delay
= Area 8 Exit Delay
N
N
N
N
N
N
N
N
N
1285
1286
1287
1288
1289
1290
1291
1292
-
Area
Area
Area
Area
Area
Area
Area
Area
1
2
3
4
5
6
7
8
Exit
Exit
Exit
Exit
Exit
Exit
Exit
Exit
Delay
Delay
Delay
Delay
Delay
Delay
Delay
Delay
Expires
Expires
Expires
Expires
Expires
Expires
Expires
Expires
N
N
N
N
N
N
N
N
1293 = Automatic Closing
1294 = Early Closing
1295 = Closing Time Extended
1296 = Fail to Close
1297 = Late to Close
1298 = Keyswitch Closing
1299 = Duress
1300 = Exception Opening
1301 = Early Opening
1302 = Fail to Open
1303 = Late to Open
1304 = Keyswitch Opening
B
B
B
B
B
B
B
B
B
B
B
B
1305 = Area 1 Closing Ring Back
1306 = Area 2 Closing Ring Back
1307 = Area 3 Closing Ring Back
1308 = Area 4 Closing Ring Back
1309 = Area 5 Closing Ring Back
1310 = Area 6 Closing Ring Back
1311 = Area 7 Closing Ring Back
1312 = Area 8 Closing Ring Back
B
B
B
B
B
B
B
B
Event
1313
1314
1315
1316
1317
1318
1319
1320
1321
1322
1323
1324
1325
1326
1327
1328
1329
Description
Reset
= Access Keypad 1
= Access Keypad 2
= Access Keypad 3
= Access Keypad 4
= Access Keypad 5
= Access Keypad 6
= Access Keypad 7
= Access Keypad 8
= Access Keypad 9
= Access Keypad 10
= Access Keypad 11
= Access Keypad 12
= Access Keypad 13
= Access Keypad 14
= Access Keypad 15
= Access Keypad 16
= Access, Any Keypad
TM
TM
TM
TM
TM
TM
TM
TM
TM
TM
TM
TM
TM
TM
TM
TM
TM
1330 = Keypad Beep Area 1
1331 = Keypad Beep Area 2
1332 = Keypad Beep Area 3
1333 = Keypad Beep Area 4
1334 = Keypad Beep Area 5
1335 = Keypad Beep Area 6
1336 = Keypad Beep Area 7
1337 = Keypad Beep Area 8
N
N
N
N
N
N
N
N
1338 = Area 1 Exit Error
1339 = Area 2 Exit Error
1340 = Area 3 Exit Error
1341 = Area 4 Exit Error
1342 = Area 5 Exit Error
1343 = Area 6 Exit Error
1344 = Area 7 Exit Error
1345 = Area 8 Exit Error
N
N
N
N
N
N
N
N
1346 = Audio Amplifier Status
TMC
1347 = Control Power Status
N
1348 = Light
N
1349 = Dark
N
1350 = Security (Day) Alert
TMC
1351 = Dialer Abort
B
1352 = Dialer Cancel
B
1353 = Dialer Auto Test
B
1354 = Local Programming Begin
N
1355 = Local Programming End
B
1356 = Keyswitch Security Alert TMC
1357 = Event Log is 80% Full
N
1358 = Telephone Line Is Ringing
B
1359 = Telephone Line Seized Status T
1360 = Telephone Line Hook Status T
1361 = Telephone Local Access
T
1362 = Telephone Remote Access
T
1363 = Remote Programming Start N
1364 = Remote Programming Stop
B
1365 = AC Fail Tbl - Power Supv Zn N
1366 = Low Batt Tbl - Pwr Supv Zn N
1367 = System Start Up
B
1368 = Control Low Volt Shutdown
N
1369 = RF Keyfob Button 1
B
1370 = RF Keyfob Button 2
B
1371 = RF Keyfob Button 3
B
1372 = RF Keyfob Button 4
B
1373 = RF Keyfob Button 5
B
1374 = RF Keyfob Button 6
B
1375 = RF Keyfob Button 7
B
1376 = RF Keyfob Button 8
B
1377 = Lost Serial Port Exp Tbl
N
1378 = Rule Triggered Voice Dial
B
1379 = Dialer Report Cleared
B
1380 = Central Station Kissoff
B
1381 = Transmitter Supervision Loss N
1382 to 2000 = No Event/Not Used
Event
Description
Reset
2001 = Automation Control 1
~
2032 = Automation Control 32
TF
2033 to 3000 = No Event/Not Used
N
3001 = F1 Key on Keypad 1
3002 = F2 Key on Keypad 1
3003 = F3 Key on Keypad 1
3004 = F4 Key on Keypad 1
3005 = F5 Key on Keypad 1
3006 = F6 Key on Keypad 1
3007 to 3012 = F1 to F6 on KP 2
3013 to 3018 = F1 to F6 on KP 3
3019 to 3024 = F1 to F6 on KP 4
3025 to 3030 = F1 to F6 on KP 5
3031 to 3036 = F1 to F6 on KP 6
3037 to 3042 = F1 to F6 on KP 7
3043 to 3048 = F1 to F6 on KP 8
3049 to 3054 = F1 to F6 on KP 9
3055 to 3060 = F1 to F6 on KP 10
3061 to 3066 = F1 to F6 on KP 11
3067 to 3072 = F1 to F6 on KP 12
3073 to 3078 = F1 to F6 on KP 13
3079 to 3084 = F1 to F6 on KP 14
3085 to 3090 = F1 to F6 on KP 15
3091 to 3096 = F1 to F6 on KP 16
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
3097
3098
3099
3100
3101
3102
3103
3104
= F1 Key, Any KP Is Pressed
= F2 Key, Any KP Is Pressed
= F3 Key, Any KP Is Pressed
= F4 Key, Any KP Is Pressed
= F5 Key, Any KP Is Pressed
= F6 Key, Any KP Is Pressed
= Any KP Key Is Pressed
to 4000 = No Event
B
B
B
B
B
B
F
4001 to 4208 = Zone State 1 to 208
4209 to 5000 = No Event
T
5001 to 5208 = Bypass State 1 to 208 T
5209 to 6000 = No Event
6001 to 6208 = Alm Memory 1 to 208 T
6209 to 7000 = No Event
7001 to 7208 = Output State 1 to 208 N
7209 to 8000 = No Event
8001 thru 9999 = No Event
“Reset” Attribute
The letter(s) displayed in Reset column indicate what condition(s) it takes to
clear an event once it has been activated.
For example: the letters TMC indicate the event will reset when the output
timer ends, or when manually turned off, or when a valid user code is
entered, whichever comes first.
NOTE:
The reset attributes are shown only for informational purposes. They are set
by the factory and cannot be altered.
N
T
M
C
A
D
B
F
(0)
(1)
(2)
(4)
(16)
(32)
(64)
(128)
Event
Event
Event
Event
Event
Event
Event
Event
follows the activation
clears when output timer ends
clears when manually turned off
clears upon User Code entry
clears upon Arming
clears upon Disarming
clears almost immediately “Blip”
toggles with each activation
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
TF
[Effective w/Firmware 4.3.6]
Page 57
Appendix B - Two Way “Listen-in/Talk” Interface (optional)
Using a Two Way Interface board (ELK-EZ8TWI), up to 3 zones of listen-in can be provided. Each zone can have up to 4
microphones for a total of 12 listen-in points. Talk back is delivered through the speakers connected to the EZ8TWI. A
two way session can be triggered by any number of zones when an alarm occurs. Two way can also be triggered during
a Telephone Remote Control session. Instructions for the ELK-EZ8TWI are included with the interface.
OPERATION
1. Two way Listen-in must first be enabled from Menu 07-Global System Options. There are two required options.
Option 31, “2Way Listen-in Enable” (No or Yes) and Option 32, “2Way Callback Time” (000 to 255 seconds). These
options are defaulted to No and 000. In addition, you must also decide which zone(s) need to activate listen-in and set
their “Enable Listen-in” programming option. Whenever a Central Station alarm message is transmitted for one of these
zones, the dialer provides two methods for initiating a listen-in session.
1a. Hold the Line - After alarm kissoff the dialer will hold the phone line open for the amount of time programmed in
Option 32, “2Way Callback Time”. This can be from 001 to 255 seconds. During this time the Operator may pick up the
line and press * 55 * to initiate an immediate two way session. If the control does not receive * 55 * during the time
period it will hang up and release the phone line.
1b. Callback - Upon hangup the control uses the same time value (Option 32, “2Way Callback Time”) to begin a callback time window. During this time window the control will answer any incoming call on the 1st ring, and allow the
Operator to press * 55 * to initiate a two way session.
2. Once a two way session has begun, it will continue for 3 minutes before automatically disconnecting. To extend the
two way session for 3 additional minutes you must press command 7.
* 55 *
1
2
3
4
5
6
7
8-8
9-9
0
*
#
TONE COMMANDS
BEGIN LISTEN-IN Used by Operator to begin a listen-in session.
TALK
Talk through all speakers connected to Output 1.
LISTEN All 3 microphone zones are enabled initially. Use key 4 to change mics.
SENSITIVITY INCREASE Raise the microphone gain.
MICROPHONE SELECT 4+0 Selects ALL microphones, 4+1 Mic1 zone, 4+2 Mic2 zone, 4+3 Mic3 zone
[future use]
SENSITIVITY DECREASE Lowers the microphone gain.
EXTEND TIME for 3 minutes
TERMINATE SESSION and enable 1 ring callback answer for selected time.
TERMINATE SESSION without enabling callback answer mode.
[future use]
CANCEL last key-press (undo )
[future use]
Dialer Activated (Alarm)
Dialer remains off-hook for time set
in Menu-07, Option 32, "2 Way
Callback Time" looking for command
* 55 * to start a two-way session.
Dialer seizes house
phone line, dials
Central Station and
sends report, then
receives Kissoff.
Yes
Command
*55* received?
Two way listen-in starts. It ends after 3
minutes or when command 99 is pressed.
End
No
Dialer hangs up. Phone line is un-seized.
Was
the alarm from
a listen-in
Zone?
Yes
No
Dialer hangs up. Phone
line is un-seized.
Page 58
Phone line is seized again after 5
seconds. "2 Way Callback Time"
restarts, during which time the
dialer will answer any incoming
call on the 1st ring.
Phone rings Yes
Dialer
before timer
Answers
expires?
Command Yes
* 55 *
received?
No
No
"CS Verify Call Time" starts, if set. (Menu-07, Option 33) Dialer will not dial additional alarm
reports during this time, keeping phone line free for Central Station "Voice" Verification.
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
Two way
listen-in
starts.
It ends after
3 minutes or
when
command
99 is
pressed.
End
END
M1EZ8 Installation and Programming
Appendix C - SIA CP-01 Compliance
This Control complies with the SIA CP-01 Control Panel Standard - Features for False Alarm Reduction
PROGRAMMABLE FEATURES, SHIPPING DEFAULTS, AND RECOMMENDED PROGRAMMING
FEATURE
CP-01 Std.
Par. #
REQUIREMENT
ALLOWABLE RANGE / PURPOSE
RECOMMENDED
PROGRAMMING *
SHIPPING
DEFAULT
Exit Delay Time 1 & Exit Delay Time 2
4.2.2.1
Required
(programmable)
45 - 120 sec. (2 minutes) for full or auto
arming Shall not exceed 255 seconds
60 Seconds
60 Seconds
Silent on Exit (Disable Exit Progress
Annunication - ie: Silent Exit)
4.2.2.2
Allowed
Individual keypads may be disabled
All Audible Annunciators
All Audible
Annunciators
Exit Time Restart
4.2.2.3
Required Option
Only one restart during arming.
Enabled
Enabled
Auto Interior Off (Auto "Stay" Arm on
Unvacated Premises)
4.2.2.5
Required Option
(except for remote arm)
Away arm changes to Stay Arm
if there is no exit detected.
Enabled
Enabled
Entry Delay Time 1 & Entry Delay
Time 2
4.2.3.1
Required
(programmable)
30 sec. to at least 240 sec.
(4 minutes) minimum **
At least 30 Seconds **
30 Seconds
Comm Abort Time (Abort Window) for
Non-Fire Zones. 000 time = Disabled
4.2.5.1
Required Option
May be disabled - by zone or zone type
Enabled (all zones)
Enabled
Comm Abort Window Time - for NonFire Zones
4.2.5.1
Required
(programmable)
15 sec. - 45 sec. **
At least 15 seconds
30 Seconds
Abort Annunciation ***
4.2.5.1.2
Required
Annunciate that no alarm was transmitted
Enabled
Enabled - No
disable option
Cancel Annunciation ***
4.2.5.4.1
Required
Annunciate that a Cancel was transmitted
Enabled
Enabled - No
disable option
Duress (Individual User Code Option)
4.2.6.1
& 4.2.6.2
Allowed Option
Cannot be a 1+ or derivative of another
user. No duplicates with other user codes
Disabled
Disabled
Cross Zoned (Zone Option)
4.3.1
Required Option
Violation of a zone defined as Cross zone
requires verification by another zone
Enabled and two (or
more) zones programmed
Disabled
Cross Zone Verify Time
4.3.1
Allowed
Programmable from 1 to 255 seconds.
Time based on walk path
in protected premises
30 Seconds
Single Alarm Lockout (Swinger
Shutdown)
4.3.2
Required
(programmable)
For all non-fire zones,
shut down at 1 trip.
Enabled
Enabled
Fire Verified Zone Definitions (Fire
Alarm Verificatoin)
4.3.3
Required Option
Depends on Panel and Sensors
Enabled unless sensors
can self-verify
Disabled
Required
Call waiting cancel prefix code may be
dialed on initial attempt ONLY.
Depends on User Phone
Line
Blank - Not
Programmed
Call Waiting Cancel ***
4.5
* Programming at installation may be subordinate to other UL requirements for the intended application.
** Combined Entry Delay and Abort Window should not exceed 1 minute.
*** Feature is pre-defined in the panel software and may not be altered.
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 59
Appendix D - Regulatory Agency Statements
FCC Information: This control complies with Part 68 of the FCC rules. On the front nameplate of the main control board is a label that contains, among other
information, the FCC certification number and ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone
company. This equipment uses an RJ31X jack to connect to the telephone network. The REN is used to determine the quantity of devices that may be connected to
the telephone line. Excessive REN’s on the telephone line may result in the devices not ringing in response to an incoming call. Typically, the sum of REN’s should
not exceed five (5.0). To be certain of the number of devices that may be connected to a line (as determined by the total RENs) contact the local telephone
company.
If this equipment should happen to cause harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service
may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to
file a complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations, or procedures that
could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary
modifications in order to maintain uninterrupted service. If trouble is experienced with this equipment, please contact the manufacturer for repair and warranty
information. Elk Products, Inc. 3266 Hwy 70 W. Hildebran, NC 28637 828-397-4200 If the trouble is causing harm to the telephone network, the telephone
company may request you remove the equipment from the network until the problem is resolved.
There are no user serviceable components in this product. All necessary repairs must be made by the manufacturer. Other repair methods may invalidate the FCC
registration on this product. This equipment cannot be used on telephone company-provided coin service. Connection to Party Line Service is subject to state tariffs.
This equipment is hearing-aid compatible.
This control complies with Part 15 of FCC Rules which are designed to provide reasonable protection against such interference in a residential installation. The FCC
requires the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions,
may cause Interference to radio and television reception. It has been type tested. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
* If using an indoor antenna, have a quality outdoor antenna installed.
* Reorient the receiving antenna until interference is induced or eliminated.
* Move the receiver away from the security control.
* Move the antenna leads away from any wire runs to the security control
* Have the security control plugged into a different outlet so that it and the receiver are on different branch circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user or installer may find a booklet titled
“Interference Handbook” prepared by the Federal Communications Commission helpful: This booklet is available from the U.S. Government Printing Office,
Washington, DC 20402. The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or Users Manual.
Unauthorized changes or modifications could void the user’s authority to operate the equipment.
Canada IC: 4353A-M1GCB REN 0.3B
This product meets the applicable Industry Canada technical specifications. The REN “Ringer Equivalence Number” is an indication of the maximum number of
devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the
requirement that the sum of the RENs of all the devices does not exceed five.
UNDERWRITERS LABORATORIES UL INFORMATION
When installing an M1EZ8 in compliance with Underwriters Laboratories, the following instructions must be observed.
*
Total combined continuous current draw from terminals +SMK, +VAUX, +12V KP, and connector J16 is 1 Amp (2.5 Amp in alarm).
*
For 4 hours of standby power, limit auxiliary power load to 1 Amp and use one (1) 8 Ah battery.
*
For 24 hours of standby power, limit auxiliary power load to 500 mA and use two (2) 8 Ah batteries in parallel.
*
Force Arming and Auto Arming shall not be enabled
*
For residential fire applications the indicating devices shall be a Wheelock 34T-12 or equivalent.
*
Initiating and indicating devices must be rated at 11.5 to 12.4 VDC.
*
For residential applications the minimum alarm cutoff time for the audible devices shall be 4 minutes.
*
Zone Swinger Shutdown shall not be enabled.
*
Remote Downloading shall not be used on UL Listed systems.
*
Communicator Dial Delay time shall be set to “0”.
*
For residential burglary applications the maximum entry delay time shall be 45 seconds and the max. exit delay time shall be 60 seconds.
*
24-hour communicator test transmission is required.
*
The silent keypad option shall not be enabled.
MINIMUM SYSTEM CONFIGURATIONS FOR UL INSTALLATIONS
(Residential Burglary, Residential Fire)
*
*
At least one compatible keypad is needed for all applications.
At least one bell fixture is required for all applications.
Page 60
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
[Intentionally left blank]
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 61
[Intentionally left blank]
Page 62
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
[Intentionally left blank]
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 63
Appendix E - Additional Keypad Information
Detail A
Bend (arch) the 5 wires from the M1PR wiring plug as
shown. This provides space between the plug and the
connector (J2) so that they may be attached.
ELK-M1KP LCD Keypad
M1PR Wiring Plug
Back (Circuit) Side of Keypad
J2
J1
ELK-M1PR
Six (6) conductor plug-in data bus cable
(4 wires go to the Control, 1 is a zone input
and 1 is a programmable output).
J2
J2
Connector
J1
ELK-M1PR
Built-in Temperature Sensor If the Keypad local temperature reads
too high after installation of the M1PR Mini Prox Reader, it may be
necessary to adjust the keypad temperature reading to compensate
for the added heat produced by the M1PR. Refer to the M1KP
Instructions or contact ELK Technical Support.
Detail C
An external Prox Reader (26 bit Wiegand compatible) from another
manufacturer may be connected to the ELK-M1KP Keypad in place of an
internal ELK-M1PR Mini Prox Reader. This requires an optional ELK-WO35A
Cable Assembly. Splice wires as indicated, and plug cable into connector J2.
Brown
Detail B
ELK-M1PR
Note: Earlier version
keypads do not have the
newer (white) polarized J2
jack. For these type
keypads; the small
polarizing tabs need to be
cut off so the connector will
fit onto the J2 jack.
Green
Black
White
Red
ELK-WO35A Cable Assembly
External
Prox Reader
(26 bit
Wiegand)
from other
Manufacturer
Red
White
Black
Green
Brown
Installing a ELK-M1PR internal prox reader or an external (26 bit Wiegand) prox reader
1.
2.
3.
4.
5.
Turn Off the Control’s Master Power Switch.
Remove M1KP Keypad from mounting plate, disconnect the 6 pin data bus cable, and place face down on a soft surface.
Locate the 1" mounting hole in the lower left corner and the 5 pin connector marked J2 to the right of the mounting hole.
Position the M1PR in the 1" mounting hole with its 5 wire female cable facing towards connector J2 on the circuit board.
Gently lift up on the 5 wire cable, then bend the white plug down to form a slight arch in the wires.
SEE DETAIL A. This will shorten the cable enough that it can be plugged into connector J2.
6. Reconnect the 6 pin data bus cable to connector J1 and install the keypad onto its mounting plate.
7. Turn On the Control’s Master Power Switch and follow the instructions for enrolling cards or fobs
Enrolling Prox Cards and Fobs
Prox cards/fobs are enrolled into a User Code location using the same procedures used to add/change User Code PINs.
1. Press the ELK key, then press the 6 key (or scroll up) to display 6 - Change User Codes. Press the RIGHT arrow key to
select this menu. A Master user code (PIN) must be entered to gain access to this menu.
2. Enter the three digit number of the desired User Code location (001 to 099) or use the UP or DOWN arrow keys to scroll
through the codes. Then select CHG by pressing the RIGHT arrow key.
3. The keypad will display any existing 4 or 6 digit code that is programmed for this user along with any programmed name.
4. Place a new (not previously enrolled) prox card/fob near the Keypad's right speaker grill below the Stay key. The read range
is approximately 1/8" to 3/8". The Keypad should beep 3 times and display the card/fob 12 digit ID.
5. If the card/fob is rejected, a low error tone and Code Not Authorized, Redo will display. Causes for reject include: A. The
card/fob has already been enrolled (duplicate codes are not allowed) OR B. The facility code in the card/fob does not
match the reader facility code. A prox reader can only read cards/fobs with a matching facility code.
6. Once a prox card/fob is enrolled in a user code location, its capabilities are set by the User Code Options found in Installer
Menu 02. The commonly used options are: Arm the Control, Disarm the Control, or Access event.
A keypad access event occurs when a valid prox card/fob is read at a keypad. Nothing will happen until this event is utilized in
a Whenever/And/Then Rule from the Elk-RP software. An Access event can be used to create virtually any desired reaction.
i.e., turn on an output, a light, close/open a relay, etc. The following rule example turns on Output 003 for 10 seconds when a
valid prox card/fob (with Access Option enabled) is read at Keypad 01. This could be used to break power to a door strike.
WHENEVER Keypad 01 Access is Activated
THEN Turn On Output 003 for 10 seconds.
Page 64
WWW.DIYALARMFORUM.COM
[Effective w/Firmware 4.3.6]
M1EZ8 Installation and Programming
Appendix E - Additional Keypad Information
(cont.)
KEYPAD INTERNAL TEMPERATURE SENSOR
Every standard ELK-M1KP has a built-in temperature sensor, which detects the surrounding ambient temperature. The
sensor temperature may be displayed on the LCD, and read from another keypad or the telephone remote control. It may
also be used with the Elk-RP Whenever/And/Then Rules to automatically cause an action or control something. i.e., a fan,
pump, light, etc.
Viewing a Keypad temperature sensor reading
1. To view a keypad temperature sensor press the ELK key once (enter code if prompted), then press the RIGHT arrow to
select the View/Control Automation menu.
2. Press the 5 key (or scroll up) to display: 4-Keypad Temperature, then press the RIGHT arrow key.
3. The first Keypad (Keypad 01 will be displayed along with its Name, Keypad Number, and Temperature.
4. Additional Keypad Temperature sensors (if any) may be displayed by entering the 2 digit Keypad number OR by scrolling
with the UP or DOWN arrow keys. To exit from this menu press the * key.
Using a Keypad temperature reading in a Rule to create an action or output
The following is an example of an ELK-RP Whenever/And/Then Rule to automatically turn on Output 3 (controlling a Fan, etc.)
for 10 minutes whenever the Keypad temperature reading exceeds 90 degrees.
1. Start RP and open an account. Click the Automation tab and the Rules tab followed by New.
2. Click Trigger, then point to Time Occurrence, then Every X Seconds, and then click to select. **
3. In the block beside the words Fixed Value, type in 30 and click OK.
4. Click And, follwed by Temperature which is located near the bottom of the drop down list.
5. Highlight the Keypad temperature sensor (by name), click the Greater than button, and change the temperature selection
number to 90. Make sure the button beside F is selected, and click OK.
6. Click Then, followed by Turn Output On/Off. Highlight Output 3 (use the scroll down arrow), make sure the button beside
Turn on is selected, then select the box labeled For. Highlight the hrs:mins:secs window and enter 00:10:00 (10 minutes). Click OK. Double check everything and click Done.
7. The completed Rule should resemble the example below.
** Numerous triggers may be used for a temperature type rule, i.e., time occurence, arming of the security system, opening of a zone, etc.
However, the control does not allow a temperature reading to be used as a trigger. This helps prevent a false activation "runaway" that
could occur simple because the temperature has fluctuated by a degree or fraction of a degree. Instead, the AND command is used to
compare or "test" a temperature sensor reading against a target value, each time the trigger occurs. The target value is programmable and
the compare options are "Equal to, Not equal to, Less than, and Greater than". The "Equal to" is not recommended as a compare option
because it may be impossible for a temperature reading to be exactly at the target value when the trigger occurs.
TEMPERATURE READING ADJUSTMENT
If the Keypad internal temperature sensor appears to read higher or lower than other room thermostats/thermometers, it may be
due to the Keypad mounting location, the room conditions, or the installation of a optional Mini Prox Reader (ELK-M1PR). The
Keypad has an adjustment procedure which allows compensation for these conditions.
1. Press and hold the " * " key, followed by the F5 key . HOLD BOTH keys pressed for 5-10 seconds or until the LCD displays
Exit when done. F1 Set Addr. (This is Keypad setup mode)
NOTE: This mode may also be accessed by removing power from the keypad (unplugging the data bus cable) and then
applying power while holding any key pressed.
2. Press the F2 key and the LCD will display: Temperature Degrees F = XX.X (This is the current temperature)
3. Use the UP or DOWN arrow keys to adjust the current temperature display until it approximates the desired setting. Each
press of the arrow keys changes the setting by approximately 3 tenths of a degree (00.3) It may not be possible to end up
exactly on an even temperature setting.
4. Press the Exit key twice do return back to the regular operation mode.
WWW.DIYALARMFORUM.COM
M1EZ8 Installation and Programming
[Effective w/Firmware 4.3.6]
Page 65
EZ8 LIMITED WARRANTY
The ELK-EZ8 and its associated component products are warranted by Elk Products, Inc. (“Manufacturer”) against defects in
material and workmanship for a period of two (2) years from the date of manufacture. If product is found to be defective during
the first 180 days, manufacturer may allow an over the counter exchange, subject to inspection and approval by one of it’s
representatives. Manufacturer’s obligations under this Limited Warranty shall be limited to repairing or replacing, at its option,
free of charge, during this warranty period, any product returned to Manufacturer freight prepaid. After the expiration of the
warranty period, product will be repaired based on a fixed charge per device.
Manufacturer shall have no obligation under this Limited Warranty or otherwise if (1) the Product has been damaged by
negligence, accident, mishandling, lightning or flood, or other Acts of God, (2) the Product has not been operated in
accordance with its operating instructions, (3) the Product has been altered or repaired by anyone outside Manufacturer’s
authorized facilities (4) adaptations or accessories have been made or attached to the Product which, in Manufacturer’s sole
determination, have adversely affected its performance, safety or reliability.
If a Product should malfunction or fail during it’s warranty period, contact ELK or one of its authorized distributors for a Return
Authorization (RMA) number. Returned Products must include a complete description of the problem, along with the RA
number clearly marked on outside of the package. Manufacturer will not be responsible for any unnecessary items included
with any returned Product.
THIS WARRANTY IS THE EXCLUSIVE WARRANTY FOR ANY PRODUCT. MANUFACTURER SPECIFICALLY DISCLAIMS ANY
AND ALL OTHER WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTIES OF FITNESS FOR A
PARTICULAR PURPOSE OR OF MERCHANTABILITY. MANUFACTURER SHALL NOT BE LIABLE IN TORT, INCLUDING
NEGLIGENCE OR STRICT LIABILITY, AND SHALL HAVE NO LIABILITY AT ALL FOR INJURY TO PERSONS OR PROPERTY.
MANUFACTURER’S LIABILITY FOR FAILURE TO FULFILL ITS OBLIGATION UNDER THIS LIMITED WARRANTY OR ANY
OTHER LIABILITY IN CONNECTION WITH A PRODUCT SHALL BE LIMITED TO THE AMOUNT OF THE PURCHASE PRICE
RECEIVED BY MANUFACTURER FOR THE PRODUCT. THE REMEDIES STATED IN THIS LIMITED WARRANTY ARE THE
CUSTOMER’S EXCLUSIVE REMEDIES AGAINST MANUFACTURER REGARDING ANY PRODUCT. UNDER NO
CIRCUMSTANCES SHALL MANUFACTURER BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES, INCLUDING LOST PROFITS AND REVENUES, INCONVENIENCE OR INTERRUPTIONS IN OPERATIONS, OR ANY
OTHER COMMERCIAL OR ECONOMIC LOSSES OF ANY KIND. THESE LIMITATIONS AND DISCLAIMERS ARE NOT MADE BY
MANUFACTURER WHERE PROHIBITED BY LAW. SOME STATES PROHIBIT LIMITATIONS OF WARRANTIES AND THE
CUSTOMER MAY HAVE ADDITIONAL RIGHTS IN THOSE STATES.
WWW.DIYALARMFORUM.COM
Index
A
Alarm Abort 38
Alarm Cutoff Timers 31
Anti-Takeover 19
Area Partitioning 19
Area Reporting Codes 38, 39
Auto Stay Option 25
Automation control function 15
Automation Tasks 49
Auxiliary Power Connections 9
B
Installer Program Code
13, 15, 19, 20, 23
K
Keypad Addresses 22
Keypad Definitions 27
Keypad Menus 15
L
Lighting 50
Listen-In 31
M
Battery Connection 9
Bus Module Enrollment 23
C
Canada IC 60
Central Station alarm verification 34
Communicator Setup Checklist 20
Counters 51
CrossZonePool 31
CrossZoneVerTime 33
D
Data Bus Device Types/Addresses 22
Daylight Savings Time 33
Defaulting the Control 34
Dialer Delay 31
Dialer Delay Time 39
Duress 22
E
Entering Installer Level Programming 20
Entry delay time 24
Event Codes - Appendix A 56
Exit delay time 24
Exit Error 24
Exit TimeRestart 25
Exit1TimeRestart 25
F
Menu 01 - Bus ModuleEnrollment 23
Menu 02 - User Code Authorities 23
Menu 03 - Area Definitions 25
Menu 04 - Keypad Definitions 26
Menu 05 - Zone Definitions 28
Menu 06 - Alarm Cutoff Timers 31
Menu 07 - Global System Definitions 32
Menu 08 - Telephone Account Setup 36
Menu 09 - Area Reporting Codes 38
Menu 10 - Zone Reporting Codes 40
Menu 11 - Sys Report Code Options &
Codes 41, 42
Menu 12 - User Report Codes 45
Multi-area (Partition) Operation 18
S
Serial Port Baud Rate 35
SIA CP-01 Compliance - Appendix E 59
Silent Alarm 29
SingleAlmLockout 35
Specifications, Features, and Benefits 4
Sunrise/Sunset 50
SwingerShutdown 31
Sys Rpt Code Options 42, 43
T
Tasks 49
Telephone Account Setup 36, 37
Telephone Line Connection 10
Temporary Code 22
Texts 51
Thermostats 51
Transformer Power Input (AC) 9
Two Way Listen-in 34
U
Underwriters Laboratories 60
Update/Verify Firmware 48, 49
User Code 13, 15
User Code Options 22
V
O
Verify Call Time 35
Operating The System 13
Output 1 Delay Turn-On 32
Outputs 10, 50
W
P
PeriodicTrip 31
Prox Reader 64
Q
Quick Reference Programming Guide 21
Quickarm 24
Whenever/And/Then 53
WirelessDefinitions 45
Wiring & Hookup Diagram 5
WrongCodeLockout 33
Z
Zone Definitions 29, 30
Zone Reporting Codes 40, 41
Zone Wiring Types 29
R
FCC Information 60
Force Arm 30
Four (4) State Zone 8
G
Global Sys Definitions 32, 33, 34, 35
Regulatory Agency Statements Appendix F 60
Ring/Hang/Answer option 34
Rings Until Auto Answer 35
RP Software 47
Rules 53
I
Input/Output Expander Addresses 22
Installation and Wiring 7
WWW.DIYALARMFORUM.COM
www.elkproducts.com
Printed in USA
WWW.DIYALARMFORUM.COM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising