Keyboard Controller

PIH-800II

MERIT LI-LIN ENT. CO., LTD http://www.meritlilin.com

66-800IICSE

INSTRUCTION MANUAL

CAUTION

RISK OF ELECTRIC SHOCK

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

CAUTION

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT OPEN COVER.

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit.

PRECAUTIONS

Do not drop or strike this equipment.

It will cause damage to the equipment.

Do not install the equipment near any naked flames or heat sources.

The presents of flammable gas or object in the operating environment or exposing this unit to direct sunlight may cause fire and severe injury.

Do not expose this unit to rain , moisture , smoke or dust environment.

May cause short circuit, fire and serious damage to this unit.

Unplug this unit and have it checked by qualified service personnel.

Do not cover the opening of the cabinet with cloth and plastic or to install this unit in poor ventilated places. Allow 10cm between this unit and its surroundings.

May cause overheat. The normal operating temperature is 0 C ~ 40 C.

Do not continue to operate the unit under abnormal conditions such as detection of smoke, strange smell or no display on screen while power is turned on.

Contact qualified service personnel for help.

Do not touch the power connection with wet hands.

May cause short circuit or electric shock.

Do not damage the power cord or leave it under pressure.

May cause fire or shock hazard.

Do not operate this unit near magnet, speaker system, etc., to avoid unnecessary magnetic interference.

These interference will cause color confusion and screen fluctuation.

Do not drop metallic parts through slots.

This could permanently damage the appliance.

Connection cables should be grounded properly.

Sudden surge such as lightening will damage the system permanently.

PREFACE

Thank you for choosing PIH-800II keyboard. For trouble free installation and optimum performance please read this manual thoroughly before attempting installation or operation.

CONTENTS

1. Introduction

2. Specifications

3. Keyboard Layout

4. Matrix and Receiver Operation

5. Fast Speed Dome Operation

6. Wiring Diagrams

7. Master & Slave Settings

Page

2

3,4

5,6

2

2

6

7

1

1. INTRODUCTION

The PIH-800II is a control keyboard For a rage of matrix switchers, dome cameras and telemetry receivers. It allows operation of all the functions of that equipment an provides an simple operator interface.

When matrix is present in the system, up to 8 keyboards can be used ,howeve,r one keyboard must always be configured as the Master, having greater access to settings than the slaves.

If when keyboard is controlling Fast Domes directly without matrix, only one keyboard is allowed.

Data is transmitted via screened, twisted pair cables, usually in serial configuration.(RS-485)

2. SPECIFICATIONS

Data Communication

Input Voltage

Power Consumption

Operating Temperature

Weight

Dimensions

RS-485, 9600 Baud

12Vdc

250mA

-5 C ~ +60 C

1.5Kg

370(L)

5

190(W)

5

83(H)mm

3. KEYBOARD LAYOUT

Power Indicator

11 22 23

Auto Pan Indicator

16 13 14 15 12 17 18 20 19 21

Auto Focus Indicator

Auto Iris Indicator

PS. Key Functions

1. Refer to Page 3,4 when connects to Matrix Switcher.

2. Refer to Page 5,6 when connects to Fast Dome Camera directly.

2

4. MATRIX AND RECEIVER OPERATION

Function Keys

F1 Turns on or off the on-screen display.(time,date monitor and camera number)

F2 Displays the log of last 10 camera or video loss alarms.

F3 Adjust the position of the on-screen display.

F4 Sets the P/T/Z preset position groups.

Joystick

*

*

*

Controls the movement of pan and tilt cameras.

Matrix Setup Menu Selection.

Under controlling single fast dome, "9013+CLR" can rectify the joystick.

Numeric Keys

0~9 for entering camera, monitor numbers ets.

ESC Key

This can be used to exit from any function or programming.

ALARM RESET Key

Clears alarms and video loss alarms.

'

CTRL1 / CAM SETUP Key

*

*

A spare control key when keyboard connects to PIH-820 (Receiver).

OSD Setup Menu recall key when keyboard connects to PIH-7625 (Day & Night

Fast Dome)

' CTRL 2 /

*

*

180 REV Key

A spare control key when keyboard connects to PIH-820 (Receiver).

180 Horizoneal Instant Flip key when connects to Fast Dome Camera.

SPRAY Key

This operates the washer system where fitted to a camera housing.

WIPER / LENS SPEED Key

*

*

The housing wiper control key when connects to PIH-820 (Receiver).

Manual speed switch of Zoom, Focus and Iris when connects to PIH-7625 (Day &

Night Fast Dome)

AUX LIGHT / CAM ESC Key

*

*

Auxiliary lighting switch when connects to PIH-820 (Receiver).

OSD Setup Menu escape key when connects to PIH-7625 (Day & Night Fast Dome)

3

SETUP Key

Enters Matrix Setup Mode.

11 MON Key

Selects a particular monitor.

12 CAM Key

Selects a particular camera.

13 CLR Key

Selects a particular camera.

14 ENT Key

Used to enter or confirm data and programming.

15 PRESET Key

For recalling and storing preset positions.

16 PRESET 1 / 2 / 3 / 4 Keys

These Keys instantly move the selected camera to relevant preset position 1-4

17 ZOOM IN / ZOOM OUT Keys

Manually adjusted the zoom lens.

18 FOCUS FAR / FOCUS NEAR Keys

Manually adjusted the focus of the lens.

19 AUTO FOCUS Key

Auto Focus control key when connects to Fast Dome Camera.

20 IRIS O / IRIS C Keys

Manually opens or closes the iris of the lens.

21 AUTO IRIS Key

Sets the iris to automatic mode.

22 SEQ Key

Starts an automatic switching sequence on a particular monitor.

23 AUTO PAN Key

Puts a Pan/Tilt head into auto pan mode or a Fast Dome Camera into auto tour mode.

4

5. FAST DOME CAMERA OPERATION

Numeric Keys

0~9 for entering camera, monitor numbers ets.

Function Keys

F1 To set the speed that Fast Dome Camera travels between preset positions.

F2 To set the dwell time of preset position.

F3 To store the preset data

F4 To set the preset groups

Joystick

*

*

Controls the movement and speed of the dome.

Under controlling single fast dome, "9013+CLR" can rectify the joystick.

ALARM RESET Key

Clears alarms and video loss alarms.

'

CTRL1 / CAM SETUP Key

*

*

A spare control key when keyboard connects to PIH-820 (Receiver).

OSD Setup Menu recall key when keyboard connects to PIH-7625 (Day & Night

Fast Dome).

'

CTRL 2 / 180 REV Key

*

*

A spare control key when keyboard connects to PIH-820 (Receiver).

180 Horizontal Instant Flip key when connects to PIH-7625 (Day & Night Fast

Dome).

WIPER / LENS SPEED Key

*

*

The housing wiper control key when connects to PIH-820 (Receiver).

Manual speed switch of Zoom, Focus and Iris when connects to Fast Dome Camera.

AUX LIGHT / CAM ESC Key

*

*

Auxiliary lighting switch when connects to PIH-820 (Receiver).

OSD Setup Menu escape key when connects to PIH-7625 (Day & Night Fast Dome).

CAM Key

Selects a particular camera.

PRESET Key

For recalling preset positions.

5

PRESET 1 / 2 / 3 / 4 Keys

These Keys instantly move the selected camera to the relevant preset position 1-4.

11 ZOOM IN / ZOOM OUT Keys

Manually controls the zoom lens.

12 FOCUS FAR / FOCUS NEAR Keys

Manually adjusts the focus of the lens.

13 AUTO FOCUS Key

Auto Focus control key when connects to Fast Dome Camera.

14 IRIS O / IRIS C Keys

Manually opens or closes the iris of the lens.

15 AUTO IRIS Key

Sets the iris to automatic mode.

16 AUTO PAN Key

Puts a Pan/Tilt head into auto pan mode or a Fast Dome Camera into auto tour mode.

6. WIRING DIAGRAM

To Matrix or Fast Dome Camera

To 2nd Keyboard Input

RS-485 (IN / OUT)

1st Pin connects to positive, 2nd Pin to negative, leave the 3rd Pin.

6

7. MASTER & SLAVE SETTINGS

Fast Dome

ON

1 2 3 4 5 6

Alarm Buzzer

ON

1 2 3 4 5 6

6 Setting OFF 5 Setting OFF - Silent

Setting ON - ON

Matrix

ON

1 2 3 4 5 6

1st Keyboard

ON

1 2 3 4 5 6

5th Keyboard

ON

1 2 3 4 5 6

2nd Keyboard

ON

1 2 3 4 5 6

6th Keyboard

ON

1 2 3 4 5 6

3rd Keyboard

ON

1 2 3 4 5 6

7th Keyboard

ON

1 2 3 4 5 6

4th Keyboard

ON

1 2 3 4 5 6

8th Keyboard

Key Sound

ON

1 2 3 4 5 6

4 Setting OFF - Silent

Setting ON - Beep

7 66-800IICSE-4

Keyboard Controller

PIH-800II

MERIT LI-LIN ENT. CO., LTD http://www.meritlilin.com

66-800IICSE

INSTRUCTION MANUAL